REPAIRS TO JOINERIES, PLUMBING AND CERTAIN B/R WORKS TO BUILDINGS AT CORPS, DIV INF AREA UNDER AGE B/R-II UNDER GE PANAGARH

Amount

Taking down chowkats or frame n.exc 1.5 Sqm each with shutter (without taking off shutter from the frame) complete all as directed by Engr-in-Charge.

All as per item No 02.00 above but exc 1.5 Sqm and n.exc 4 Sqm each complete all as specified and directed

Taking down shutter of any description n.exc 1.0 Sqm each and easing and refixing in the same opening complete all as specified and directed

All as per item No 03.00 above but exc 1.0 Sqm and n.exc 4.0 Sqm each complete all as specified and directed .

Taking up or down steel tubing 15mm bore and connections, including cleaning for re-fixing or removal to store complete all as specified and directed

Taking up or down steel tubing 20mm bore and connections, including cleaning for re-fixing or removal to store complete all as specified and directed

Demolition of cement concrete (Unreinforced) in ground floors and pavings n.exc 15cm thickness (Below or above Ground level) complete all as specified and directed

Demolition of brickwork or stone boulder masonry built in cement or cement lime mortar including removing rubbish from the premises complete all as specified and directed

Demolition of cement concrete (Reinforced) in any description not other wise specifically provided for including cutting the reinforcement etc including removing rubbish from the premises complete all as specified and directed

Taking down cement plaster any description and the like on brick or stone walls, etc including raking out joints,hacking for key, scrubbing down with water etc including removing rubbish from the premises complete all as specified and directed

Dismantling of Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and directed

M&L for 2nd class Hard Wood plain, solid, straight chowkhats and frames wrought framed rebated on the solid rounded or chamfered put together with glue pinned at joints complete all as directed by Engr-in-Charge.

S&F 35 mm thick factory made plain framed panelled shutters (any number of panels), with panels of timber flat on both side (feather edged) or veneered particle board, medium density, wood particle board with commercial face veneers complete all as directed by Engr-in-Charge.

S&F 2nd class hardwood glazed & skeleton shutters, 30 mm open rebated & prepared to receive glass, gauze etc for windows, ventilators for etc provided with stiles & rails & divided into square with plain chamfered or mitred & rebated sash bars any numbers complete all as specified and directed

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded but wood grain printed PVC sheet used instead of Plain colour PVC sheet & 5mm thick x15mm wide PVC sheet beading used inside stiles and rails and decorative PVC beading of 10mm x 10mm (900 ) used instead of exposed portion of PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing as per specification and drawing

S&F of solid PVC door frame of size 50mmx47mm made out of 5mm single side prelam but wood grain printed PVC sheet used instead of Plain colour PVC sheet & edges will be painted to match with printed sheet as per specification and drawing.

M&L for Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 50mmX100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp?ressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardan and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made

S&F Factory made single extruded WPC (Wood Polymer Composite) solid decorative panelled decorative flush door shutter one side plain on other side of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2 , modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. (Note: stainless steel butt hinges and necessary S S screws shall be paid separately)

S&F heavy duty stain less steel butt hinges 100mm long, medium weight, cooled rolled complete all as specified and directed .

All as per item No19.00 above but 75mm long complete all as specified and directed .

S&F powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gaskey, etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engr-in-Charge.

S&F Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling,locks for sliding windows,rollers,C.P. brass/ stainless steel screws etc requried for functioning of sliding/fixied shutters all complete as per architectural drawings and the directions of Engr-in-charge.

S&F 300 mm long aluminium anodized alloy sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet cast or extruded section and fixing bolts and sliding bolts etc complete all as directed by Engr-in-Charge.

S&F 150mm long extruded Aluminium alloy handles, fabricated type anodised complete all as specified and directed .

S&F 75mm long extruded Aluminium alloy handles, fabricated type, anodised complete all as specified and directed .

S&F 150mm long extruded Aluminium anodized barrel tower bolt of extruded section and fixed complete all as specified and directed .

S&F sheet glass 4.0 mm thick, ordinary quality and glazing with beads fixed with metal panel pin in square n.exc 0.5 Sqm each complete all as specified and directed

S&F 4mm thick Figured glass, pin head type and glazing with oil putty/ beading in square n.exc 0.5 sqm in each pane complete all as specified and directed

S&F Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm fixed with stainless steel wire staples complete all as directed by Engineer-in-Charge.

M&L for PCC type C1 1:3:6, (using 20 mm graded stone aggregate) for fixing of hold fast complete all as specified and directed .

S&F mild steel hold fast made out of 25mmx3mm flat iron dully cutting/barding of required size complete all as specified and directed .

M&L for preparing surfaces of wood and wood based materials of any description and girth, back of chowkhat etc area tarred exc 0.1 Sqm but n.exc 0.5 Sqm each and treated with coal tar black paint complete all as specified and directed .

M&L for two coats of synthetic enamel paint over a coat of pink primer on new wood surfaces width or girth exc 10cm including preperation of surfaces complete all as specified and directed

S&F Floor door stopper of aluminium alloy body and tongue, anodized with hard drawn steel spring, overall length 140 mm of cover plate complete all as specified and directed

S&F in repairs double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass other parts made of mild steel heavy duty complete all as specified and directed

S&F in repair door closer hydraulically regulated, designation No.3 universal type door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all as specified and directed

M&L for brick work with sub class B bricks old size straight or curved on plan exc 6m mean radius in CM (1:6) complete all as specified and directed

M&L for brick work with sub class B bricks old half brick thick size straight or curved on plan exc 6m mean radius in CM (1:4) complete all as specified and directed

M&L for reinforced cement concrete 1:1:5:3 type A1 (using 20mm graded stone aggregate) as in chajja, fin, facia parapet, etc complete all as specified and directed

Form work to soffits of Chajja, facia, parapet etc for rough finished surface of concrete complete all as specified and directed

S&F Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed

S&F Mild steel TMT bars 6 to 8mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed

M&L for hard core with broken stone or boulders of gauge not exc 63 mm deposited spread and levelled in layers not exc 15 cm thick and well rammed to a true surfaces complete all as specified and directed

M&L for Plain cement concrete C-1 type 1:3:6 (using 20mm graded stone aggregate) 75mm thick as in plinth protection/path complete all as specified and directed

M&L for Plain cement concrete C-1 type 1:3:6 (using 20mm graded stone aggregate) as in surface channels and drains complete all as specified and directed

M&L for 50mm thick PCC 1:2:4 type B1 (using 20mm graded stone aggregate) using with nominal reinforcement as in sub base complete all as specified and directed (Note:- Reinforcement shall be measured & paid separetly)

M&L for PCC 1:3:6 type C2 (using 40mm graded stone aggregate) as in toe walls, retaing walls, butters including necessary form work complete all as specified and directed bu Eingineer-in-Charge

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using ex- tra cement, including forms, moulds, mi- tred/stopped end complete all as specified and directed

M&L for 25mm thick plain cement concrete 1:2:4 type B0 (using 12.5mm graded stone aggregate) to receive tiles complete all as specified and directed

M&L for joint free Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match using coloured tiles laid over and including screed bed or bedding layer of 15mm thick in CM 1:6 including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises complete all as specified and directed (Note : Design, shade and pattern of fixing of tiles shall be as directed by Engr-in-charge)

M&L for joint free non skid coloured ceramic tiles 7 to 8mm thick (square or rectangular) area of each tile exceeding 0.18 Sqm but not exc 0.38 sqm in floors set and jointed in neat cement slurry and pointed in coloured cement to match the shade using coloured tiles laid over and including screed bed or bedding layer of 15mm thick in CM 1:6 including Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises complete all as specified and directed (Note : Design, shade and pattern of fixing of tiles shall be as directed by Engr-in-charge)

All as per item No 51.00 above but as in skirtings/ dado over 10mm thick in CM 1:3 complete all as specified and directed (Note : Design, shade and pattern of fixing of tiles shall be as directed by Engr-in-charge)

M&L for joint free Glazed ceramic coloured tiles in vertical surfaces (250X300mm) 7mm/ 450x300x7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement ot match, with backing coat 10mm thick in CM 1:3.including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises complete all as specified and directed (Note : Design, shade and pattern of fixing of tiles shall be as directed by Engr-in-charge)

M&L for Vitrified tiles 10mm thick (Square or rectangular) polished, area of each tile not exc 0.36 Sqm in floors etc jointed in neat slurry and pointed in white or coloured cement to match the shade using coloured tiles laid over and including screed bed or bedding layer of 15mm thick in CM (1:6) including Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises complete all as specified and directed (Note : Design, shade and pattern of fixing of tiles shall be as directed by Engr-in-charge)

All as per item No 54.00 above but as in skirtings/ dado over and including 10mm thick in CM (1:3) complete all as specified and directed (Note : Design, shade and pattern of fixing of tiles shall be as directed by Engr-in-charge)

M&L for 15mm thick in CM (1:4) rendering on brick or concrete surfaces finished even and smooth with integral water proofing compound (WPC Measured and paid seperately) on wall complete all as specified and directed

Supply only integral water proofing compound (liquid admixture) complete all as specified and directed. (Makes : Pidilite Industries/ Impermo/Snowcem India Ltd/Sika)

M&L for 15mm thick in cement plaster CM (1:6) on brick or concrete surfaces finished even and smooth without using extra cement on wall complete all as specified and directed

M&L for 10mm thick in cement plaster 1:3 on concrete surfaces finished even and smooth without using extra cement on ceilings complete all as specified and directed

M&L for three coats of white wash as in ceilings on newly plastered surfaces including preperation complete all as specified and directed

M&L for two coats of oil bound distemper on walls over a coat of alkali resistant primer of newly plastered surfaces including complete all as specified and directed preparation .

M&L for Granite (of any type) tiles 16 to 18mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete over 15mm thick Screed bed or backing coat for laying floor finishes in CM 1:6 complete all as specified and directed

S&F 15mm dia Tubes medium grade galvanised with all fittings and fixed complete to walls, floor etc.complete all as specified and directed

S&F 20mm dia Tubes medium grade galvanised with all fittings and fixed complete to walls, floor etc.complete all as specified and directed

Cutting, chases for concealed water tubing and making good in CM 1:3 cutting not exceeding 10 cm girth in brick wall complete all as specified and directed

Fixing only, ‘Medium grade’ galvanised, with all fittings and fixed complete to walls and ceilings or laid in floors of 15mm bore obtained from item No 05.00 including cleaning threading if required all as specified and directed

Fixing only, ‘Medium grade’ galvanised, with all fittings and fixed complete to walls and ceilings or laid in floors of 20mm bore obtained from item No 06.00 including cleaning threading if required all as specified and directed

S&F in repairs wash down water closet (pedestal pattern) complete white with plastic water closet seat black closed pattern with flat bottom anc cover and mild steel chromium plated or aluminised hinging device and flush pipe of polythelene of low or density or PVC 32mm dia for low level flushing cistern complete all as specified and directed

S&F Vitreous china Squatting pan Orissa pattern of size 580mmx440mm wite with integral foot rests (excluding flushing cistern and flush pipe) complete including concrete bedding in repairs complete all as specified and directed

S&F PVC valveless syphonic action type flushing cistern 10 lit capacity low level white with inlet, ball valve, float and handle including brackets and 32mm PVC flush pipe in repairs complete all as specified and directed .

S&F PVC connection 15mm size with PTMT nuts of length 450mm complete all as specified and directed

S&F vitreous china wash basin, white, flat back size 600mmx480mm, incl cutting for and pinning in ends of brackets or erecting stand but excl taps, pvc conections but incl brackets in repairs complete all as specified and directed

S& in repair Vitreous China urinals,full stall type white (back or corner wall type) complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; grating and Union for discharge pipe and Waste coupling 32mm dia menimum weight 45 gms complete all as specified and directed

S&F in repair pillar taps, cast copper alloy, fancy type, chromium plated, screwed down high presure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly nuts screwed for iron pipe and fixed in repairs complete all as specified and directed

S&F Urinal spreader of CP for fixing with 15mm dia pipe (Minimum weigt 60gm) complete all as specified and directed

S&F Stop valves in repair cast copper alloy fancy chromium plated with long shank and cup( concealed) long shank 15mm bore fixed in repairs complete all as specified and directed

S&F in repairs 15 dia fancy type chromium plated bib taps cast copper alloy with crutch or butterfly handle, screwed down screwed for iron pipe complete all as specified and directed

S&F 110mm dia bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors including dismantling of extg AC pipe complete all as specified and directed

S&F tubular towel rail 20mm dia brass chromium plated D type 60cm long between flanges complete all as specified and directed

S&F PVC (SWR) multy floor trap/nahni trap 75mm dia outlet, plain with grating including jointing with solvent cement in repairs complete all as specified and directed

S&F 110mm PVC (SWR) pipes single sockected in any length with rubber ring joints fixed to walls. (SUPREME/PRINCE/ORIPLAST) including demolition of 150mm AC pipe complete all as specified and directed

S&F PVC (SWR) bends any radius of bore 110mm with access door (SUPREME/PRINCE/ORIPLAST) complete all as specified and directed

S&F PVC(SWR) junction equal or unequal of bore 110mm bore incl provided with access door (SUPREME/PRINCE/ORIPLAST) complete all as specified and directed

S&F 75mm PVC (SWR) pipes single sockected in any length with rubber ring joints fixed to walls. (SUPREME/PRINCE/ORIPLAST) including demolition of 75mm AC pipe complete all as specified and directed

S&F Grating doom 125mm dia with waste hole of PTMT(mInimun weight 40gm) complete all as specified and directed

S&F 40mm bore PVC pipes (LDPE) of pressure rating 6kg/sqcm and fixed complete to walls, ceilings or in floors complete all as specified and directed

S&F sinks with draining board made of stainless steel 1mm thick kitchen with plug washers & wastes incl bedding in cement mortar, fixing cantilever brackets & connecting union to pipe overall size 915x460mm bowl size 410x330x160mm complete all as specified and directed

S&F 250mm aluminium anodised sliding door bolts with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixinf bolt and sliding bolts of extruded section or cast alumnium alloy and fixed complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed

S&F steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I.S.1161- 1979 grade St.-240 complete all as specified and directed

S&F Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed

M&L for Pre-polished chequred cement concrete tiles of size 300mmX300mmX25mm thick, with mixture of grey cement and pigments machine pressed; set jointed and pointed in neat cement slurry in floors, and cut and polished over and including 20mm thick cement screed CM (1:6) complete all as specified and directed

M&L for 75mm thick PCC 1:4:8 type D2 (using 40mm graded stone aggregate) as in sub base complete all as specified and directed

Dismantling of Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof covering complete all as specified and directed

Dismantling of Asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings complete all as specified and directed

S&F Pre-painted fully corrugated/semi corugated galvalume aluminum zinc coating @150 GSM GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof ring/cladding to wall, fixed with self tapping screws complete all as specified and directed

S&F Pre-painted galvalume aluminum zinc coating @150 GSM GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed

M&L for 6mm thick asbestos cement, corrugated or semi-corrugated sheets in roofs, walls etc.complete all as specified and directed

M&L for taking down the existing rolling shutter manual/gear operated, cleaning of all parts with kerosine/ld oil and greasing all parts of rolling including guide rail, removing / straightening dents on lathes for easy closing/opening, and refixing in the same opening and tested easy movement while opening or closing complete all as specified and directed Note : Spare parts shall be paid separetely.

Supply only Safety lever locks mild steel with 4 levers for rolling shutters complete all as specified and directed

Supply only for Ball bearing for rolling shutters complete all as specified and directed

Supply only Helical spring of 450mm long fixed to shaft of rolling shutter complete all as specified and directed

Supply only gear box as per existing size for rolling shutter complete all as specified and directed

M&L for two coats of synthetic enamel paint on new steel surfaces including preparation over a coat of red oxide primer complete all as specified and directed

M&L for two coats of synthetic enamel paint on old steel surfaces including preparation complete all as specified and directed

S&F Hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed

M&L for Taking down the extg toughned glass door shutter 10/12mm thick exc 1.50 Sqm replacing the SS hinges suitable to shutter and tighten alll screws/nut bolts of hinges portion and handle etc including relacing the damaged portion of the rubber gasket etc, complete all as specified and directed

M&L for PCC 25mm thick 1:2:4 type B0 (using 12.5mm graded stone aggregate) as in padding for roof concrete finished even and fair complete all as specified and directed .

M&L for rendering 10mm thick in CM 1:3 finished even and fair using with water proofing compound complete all as specified and directed

M&L for preparation new surface of roof and applying two coat of polyurethene (PU) acrylic based water proofing liquid compound over & including one coat of self priming primer @one litre per ten sqm with reinforcing fabric sheet as per manufactures instruction to stop leakage /seepage from roof/wall complete all as specified and directed by the Engineer-in-Charge (notes- 1.as per description of the items minimum two coats of polyurethene (PU) acrylic based water proofing liquid compound over one coat of primer shall be carried out by the as per manufacture instruction.pl note no price adjustment shall be made,if more coats of (PU)acrlic based water proofing liquid compound & primer are required for roof treatment. 2. quated rate shall be deemed to be included for work in building/structure of any height.

BABY ENGINEERING ELECTRICAL MECHANICAL STORES

MS ROYAL CONSTRUCTION INDEX NO 158 2010 BKP

M/s sadhan kumar mukherjee

M/s BISWAJIT GHOSH