PAINTING, MARKING, PERIODICAL SERVICES, REPAIR TO HANGERS OF 665 AND 201 ARMY AVN SQN AND STONE PITCHING NEAR ATC/ TECH AREA UNDER GE NASIK ROAD.

Amount

M&L for Painting lines, dashes, arrows, letters, and painting dispersal area etc. on roads, concrete pavements and the like exc 10cm wide with road marking paint, white or golden yellow including preparation of new or previously treated surfaces to receive the painting. (Painting shall stand out boldly and solidly without showing signs of brush marks or surface underneath. If necessary, the surface shall be repainted by one or more coats until the desired result is obtained.)

M & L for painting lines, dashes, letters, arrows etc. on road pavement, parade ground and aplying 2mm thick road marking strips (reflective) of specified shade/colour using hot thermoplastic material by fully/semi automatic application mechine fitted with profile shoe heater; driven by experienced operator including preperation and cleaning of surfaces complete all as specified and as directed.

Demolition of cement concrete (unreinforced) in ground floors and pavings n exc 15cm thickness (below or above ground level).

M&L for Providing cement concrete 1:4:8 type D2 (40 mm graded aggregate) in foundations, filling, sub bases etc.

M&L for Machine pressed precast conctete interlocking paver block with grey cement and pigment with rubber moulded glossy finished surface, any shape and size confirming to IS 15658-2006 of 60 mm thickness M-25 grade laid over and including 30 mm thick stone dust cushion.

M&L for Chequered cement concrete tiles with grey cement and pigment 30cm x 30cm x 25mm thick, with rubber moulded glossy finished surface, laid in floors over and including 15mm thick cement mortar screed bed in cement mortar 1:6, set jointed and pointed in neat cement slurry in floors.

M&L for Providing precast cement concrete type B-1 1:2:4 (20 mm graded aggregate) in kerb stones with plain fair faces, including chamfers, weatherings, etc. and setting in mortar 1:4 complete with joints to match including necessary earthwork.

M&L for Preparing new or untreated brick, stone, concrete, asbestos cement or plaster surfaces of any description over 10cm girth or width, not otherwise described and two coats of synthetic enamel paint over and including priming coat.

Dismantling wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets, GI/aluminium grid etc.

M&L for Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre.

M&L for 12mm thick seamless calcium silicate ceiling made out of 1800 x 1200 mm size board of siliceous and calcareous material reinforced with cellulose fibre fixed to the ceiling section with 25 mm long self drilling and tapping screws having phillips head with under head cutter at 200 mm centre to centre, including finshing the joint of face board with specially formulated jointing compound and 48 mm wide fibre tape to provide seam less finish and two coats of distemper oil emulsion including preperation of surfaces. (Frame work for ceiling shall be measured and paid separately)

M&L for 6mm and thick PVC multiwall 250mm wide (tongue and groove interlocking type) panels, textured on one side (as approved); fixed to GI framework in ceiling with countersunk screws and inerlocked, including all necessary special fitting accessories such as junction, corner and turning matching to board. (GI framework to be measured and paid separately)

M&L for 8mm and thick PVC multiwall 250mm wide (tongue and groove interlocking type) panels wall lining including necessary framework and fixing at site on PVC frame as per specifications.

Demolition of Brickwork or stone/boulder masonry, built in cement mortar.

M&L for Brickwork with flyash bricks, straight or curved on plan exc 6m mean radius built in cement mortar 1:6 complete.

M&L for Rendering 15mm thick in cement mortar 1:4 on faces of brick work finished fair and even.

Dismantling of precast reinforced concrete cover slabs any description and in any position.

M&L for Providing precast cement concrete type B-1, 1:2:4 (using 20 mm graded aggregate) in landings, cover slabs (for drains and manholes etc.) set in cement mortar 1:6.

M&L for Mild TMT steel bars 6 to 8mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips.

M&L for One coat of oil bound distemper white or tinted on walls, including preperation of surfaces by washing, rubbing down and stopping of old distempered and painted surfaces.

M&L for One coat of oil bound distemper white or tinted on ceilings, including preperation of surfaces by washing, rubbing down and stopping of old distempered and painted surfaces.

M&L for One coat of synthetic enamel paint on old painted steel or iron surfaces of any description over 10cm width or girth including preparation of surface.

M&L for One coat of synthetic enamel paint on old painted wood or wood based surfaces of any description over 10cm width or girth including preparation of surface.

M&L for Two coat of exetior emulsion paint (apex/weathercoat) on walls and ceiling plastered or unplastered surfaces including preparing by brooming down or steel wire brushing; scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots; removing nails, making good holes, cracks etc. by filling with putty.

M&L for prepration of surface by cleaning to remove loose particles, dust, latance etc, cutting grooves properly and again remove loose particles, dust latance etc, filling cracks/gaps of RCC and masonary upto 15 mm by using Asain Paint Crack Seal or equivalent bigger cracks/damaged portions/hollow areas/gaps of RCC and masonary must be repaired with polymer modified cement motars. Applying one priming coat of SMART CARE DAMP PROOF with thinner at the rate of 0.28 Sqm/Ltr (0.20 Ltr Smart Damp Proof : 0.08 Ltr water). Applying second coat of SMART CARE DAMP PROOF after 05 to 06 Hrs at the rate of 0.2 Ltr/Sqm, all as directed and as per manufaturers instructions. Note : Cracks filler, Priming Coat and Damp Proofing coat used shall be of same Make/Manufaturer.

M&L for prepration of surface by cleaning to remove loose particles, dust, latance etc, cutting grooves properly and again remove loose particles, dust latance etc properly, filling cracks/gaps of RCC and masonary upto 15 mm to 20 mm width and 10 mm to 15 mm deep by using polymer modified cement mortars and making good, all as directed and as per manufaturers instructions.

M&L for One coat of exetior emulsion paint (apex/weathercoat) on walls and ceiling plastered or unplastered surfaces including preparing by brooming down or steel wire brushing; scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots; removing nails, making good holes, cracks etc. by filling with putty.

M&L for One coat of cement based paint on walls including preperation of old treated plastered or unplastered surfaces by brooming down or steel wire brushing; scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots; removing nails, making good holes, cracks etc. by filling with putty.

Taking down carefully existing bitumenous membrane/tarfelt treatment any description and cleaning surface to make surface ready to receive fresh water proofing treatment on roof and flashing and junctions of parapet, kerb, wall etc. and removing rubbish out of defence land.

Taking down cement or cement lime plaster, any description on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc.

M&L for Rendering 15mm thick in cement mortar 1:4 on faces of brick work or concrete surfaces finished even and smooth without using extra cement.

Demolition of concrete (unreinforced) of any description and in any position not otherwise specifically provided for.

M&L for Providing, cement concrete type B0 1:2:4 (12.5mm graded aggregate) in roof kerbs or mud stops, rounded or chamfered on edges.

M&L for Waterproofing on roof including flashing and junctions of parapet, kerb, wall etc. as under:- (a) Applying bituminous primer on cleaned and dried surface @ 0.20 Kg/Sqm. (b) A coat of hot blown type bitumen of grade 85/25, applied hot at the rate of 1.20 kg/sqm. (c) Laying on primed surface by thermo fusion (torch application) 3mm thick APP based polymeric water proofing membrane weighing not less than 3.50kg/sqm and reinforced with polyester non woven fabric (not less than 150 gms/sqm). (d) Painting the exposed APP membrane surface with bituminous aluminium paint @ 0.15 Kg/Sqm.

Dismantling water tanks exc 250 & n exc 500 ltr capacity.

Disconnecting existing tanks, exc 250 & n exc 500 setting aside (or lowering if required), cleaning and removing all scale and dirt, etc. from tanks and from mouths of circulating pipes, etc. and hoisting if required reconnecting and re-fixing in position.

S&F Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) 500 litre capacity, hoisted and fixed in position all as specified.

S & F ball valves, 20mm bore high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (Minimum weight 210gms) fixed in repairs.

Fixing only in repair ball valves any bore or size.

Dismantling asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings.

Dismantling wrought iron or mild steel work of any description such as purlins ofor roof and window guard bars.

Supply and fixing steel work in tubular or rectangular hollow section in rafters, purlins etc. and connected works complete using ERW or induction butt welded tubes conforming to I. S.1161-1979 grade St.-240

M&L for Prepainted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified.

M&L for Prepainted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified.

M&L for Preperation of new untreated steel or iron surfaces of any description over 10cm girth or width, not otherwise described and two coats of synthetic enemel paint over a coat of red oxide, zinc chrome primer.

Demolition of stone/boulder masonry, laid dry in pitching.

M&L for stone/ boulder pitching, hand packed tightly and grouted with cement and sand mortar 1:6 including raised pointed in cement mortar 1:4 (including dressing and levelling the surface).

- Ditto - but except stone/ boulders.

NOTE : - AMOUNT OF SCHEDULE OF CREDIT RS 30,862.00 WILL BE DEDUCTED FROM TOTAL AMOUNT OF BOQ.

Vinod Enterprises

Alpha Construction

RELIANCE ELECTRONICS

Bidder Name

RELIANCE ELECTRONICS

M/S SAMEER SUBHASH PATANI

Alpha Construction

Vinod Enterprises