Construction of Toilet Block for Male and Female Trainees at ITI Kathua (Balance work).

Amount

Earth work excavation in all kinds of soil by manual or mechanical means (Hydraulic excavator) in foundations, trenches, drains, pipes and cables etc. (not exceeding 1.5 m in width or 10 sqm on plan) incl. dressing of sides and ramming of bottoms, lift upto 1.5 mtr incl. disposal or filling of excavated earth as per the directions of Engineer-in-charge.

Providing and laying in position cement concrete 1: 5:10 (1 cement : 5 coarse sand : 10 graded crushed stone aggregate 40 mm nominal size) of specified grade excluding the cost of centring and shuttering including all leads, lifts and carriage of material by M.T / H.L.- All work upto plinth level.

Providing and laying in position cement concrete of specified grade 1 : 3 : 6 (1 cement : 3 coarse sand : 6 graded crushed stone aggregate 20 mm nominal size) . excluding the cost of centring and shuttering including all leads, lifts and carriage of material by MT / H.L.- All work upto plinth level.

Brick work with F.P.S. bricks of class designation 75 in foundation, plinth and superstructure including all levels, shapes, leads, lifts and carriage of material by MT / H.L. in 1:6 ( 1 cement : 6 coarse sand) cement mortar

Half brick masonry with bricks of class designation 75 in foundations and above plinth level upto 5 floor level in cement mortar 1: 4 ( 1 cement :4 coarse sand) including all leads, lifts and carriage of material by MT / H.L.

Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centring, shuttering, finishing and reinforcement-All work upto plinth level. 1:1.5:3 ( 1 cement : 1.5 coarse sand: 3 graded crushed stone aggregate 20 mm nominal size) including all leads, lifts and carriage of material by MT / H.L.

Reinforcement for RCC work incl. straightening, cutting, bending, placing in position & binding all complete Thermo Mechanically Treated bars/Cold twisted bars incl. all leads, lifts & carriage of material by MT/ H.L.

Centring and shuttering including strutting propping etc and removal of form work for

Foundations, footings, bases of columns etc. for mass concrete

Suspended floors, roofs, landings, balconies and access platform.

12 mm cement plaster of mix 1 : 6 ( 1 cement : 6 coarse sand) including drip course/groove, all leads, lifts and carriage of material by M.T / H.L.

15 mm cement plaster on rough side of single or half brick wall of mix 1:6 (1 cement : 6 coarse sand) including all leads, lifts and carriage of material by M.T / H.L.

Providing and laying damp proof course 50 mm thick with cement concrete 1 : 2 : 4 ( 1 cement : 2 coarse sand : 4 graded crushed stone aggregate 20 mm nominal size) including all leads, lifts and carriage of material by M.T / H.L ( for flooring)

Making plinth protection 50 mm thick of cement concrete 1 : 3 : 6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75 mm bed of dry brick ballast 40 mm nominal size well rammed & consolidated & grouted with fine sand including finishing the top smooth. Crushed aggregate including all leads, lifts and carriage of material by M.T/H.L.

Providing and fixing Ist quality ceramic glazed tiles conforming to IS : 13753 of minimum thickness 5 mm of approved make like NITCO, ORIENT, SOMANY KAJARIA, or equivalent make in all colour, shades except begundy, bottle green, black of any size as approved by Engineer-In-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 ( 1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm including pointing in white cement mixed with pigment of matching shade complete. including all leads, lifts and carriage of material by M.T / H.L.

Providing and fixing Ceramic glazed floor tiles 300 x 300 mm (thickness) to be specified by the manufacturers) of 1st quality conforming to IS: 13755 of NITCO,ORIENT,SOMANY,KAJARIA or equivalent make in colour such as White, Ivory, Grey, Fume Red, Brown laid on 20 mm thick bed of Cement Mortar 1:4 (1 cement :4 coarse sand) including ;pointing the joints with white cement and matching pigment etc. complete including all leads, lifts and carriage of material by MT / H.L.

Providing and fixing aluminum work for doors, windows ventilators and partitions with extruded built up standard tubular sections/appropriate Z. sections and other sections of approved make conforming to IS : 733 and IS : 1285, fixed with dash fastener of required dia and size including necessary filling up of gaps at junctions i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket felt etc. Aluminum sections shall be smooth, rust free, straight, milted and jointed mechanically wherever required including cleat angle, Aluminum snap beading for glazing/paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge( glazing, paneling and dash fasteners to be paid for separately.)

For fixed portion anodized aluminum (anodized transparent or dyed to required shade according to IS : 1868 minimum anodic coating of grade AC 15)

For shutters of doors, windows & ventilators including providing and fixings hinges/pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required( Fittings shall be paid foe separately).Anodised aluminum ( anodized transparent or dyed to required shade according to IS : 1868, minimum anodic coating of grade AC 15)

Providing and fixing ACP sheet of 4.0 mm thick in partition/ door/ window including rubber gasket of approved quality as per the direction of Engineer-in-charge.

Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC10 as per IS:1868) transparent or dyed to required colour or shade with necessary screws etc complete

Providing and fixing aluminium handles125 mm ISI marked anodised (anodic coating not less than grade AC10 as per IS:1868) transparent or dyed to required colour or shade with necessary screws etc complete

Providing & fixing aluminum sliding door bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete: 250 x 16 mm.

Providing & Placing on terrace at all floor levels polyethene water storage tank ISI: 12701 marked indicating the BIS No with cover & suitable locking arrangements & making the necessary holes for inlet, outlet & over flow pipes without the fittings & the base support for tank sintex. electroplast, star, lotous or equivalent having ISI make.

Providing and fixing G.I pipes complete with G.I fittings , including trenching and refilling etc.( external work)

15 mm dia nominal bore

20 mm dia nominal bore

Providing and fixing G.I. pipes complete G.I. fittings and clamps, including cutting & making good the walls etc.Internal Work-Exposed on wall.

15 mm dia nominal bore Medium

20 mm dia nominal bore Medium

Providing and Fixing G.I. Union in G.I. pipes including cutting and threading the pipe and making long screws etc. complete (new work).

15 mm dia nominal bore

20 mm dia nominal bore

Providing and fixing water closet squatting pan ( Indian type W.C. pan) with 100 mm sand cast iron P or S trap 10 litre low level P.V.C. flushing cistern including flush pipe pipe (of approved make ) manually controlled device ( handle lever) conforming to IS:7231,with all fittings and fixtures complete, including, cutting and making good the walls and floors wherever required. Long pan pattern white vitreous china W.C. pan of size 580 mm complete job.

Providing & fixing white vitreous china pedestal type Water closet ( European type W.C. pan ) with seat and lid,10 litre low level white P.V.C flushing cistern including flush pipe with manually controlled device( handle lever) conforming to IS : 7231, with all fittings and fixtures, complete including cutting and making good the walls and floors wherever required. W.C pan with ISI marked white solid plastic seat & lid including all leads, lifts and carriage of material by MT / H.L.

Providing and fixing wash basin with C.I / M.S brackets 15mm C.P brass pillar taps, 32mm C.P brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required. White Vitreous China. Flat back Wash basin size 450 x 300 mm with single 15mm C.P brass pillar tap

Providing and fixing white vitreous china pedestal for washbasin completely recessed at the back for the reception of pipes and fittings.

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430 x 260 x 350 mm and 340 x 410 x 265 mm sizes respectively with automatic flushing cistern with C.I./M.S. brackets standard size of G.I. flush pipe and C.P. brass spreaders with brass unions and G.I. clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required. One urinal basin with 5 litre P.V.C. white automatic flushing cistern of approved quality including all leads, lifts and carriage of material by MT / H.L.

Providing and fixing C.P brass bib cock of approved quality conforming to IS: 8931. 15 mm nominal bore complete job

Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms 15 mm dia nominal bore

Providing and fixing C.P brass angle valve for basin mixer and gyser points of approved make conforming to IS : 8931. 15 mm nominal bore complete job

Providing and fixing 80 mm dia PVC waste water/sewerage pipe of 4 kg pressure per sqm of Supreme/ Prince/finolex make.

Providing and fixing 110 mm dia PVC waste water/sewerage pipe of 4 kg pressure per sqm of Supreme/ Prince/finolex make.

Providing and fixing in position complete PVC floor trap of Supreme /Prince make 110 x 75 mm dia.

Providing and fixing on wall face un- plasticized- PVC moulded fittings/accessaries for unplasticised-Rigid PVC rain water pipes conforming to IS : 13592 Type -A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion

87.5* 75 mm bend

87.5* 110 mm bend

Single tee without door 75x75x75mm

Single tee without door 110x110x110 mm

Constructing brick masonry manhole in cement mortar 1:4 (1 cement :4 coarse sand) RCC top slab with1:2:4 mix ( 1 cement :2 coarse sand 4 graded stone aggregate 20mm nominal size) foundation concrete 1:4:8 mix (1 cement 4 coarse sand :8 graded stone aggregate 40mm nominal size) inside plastering 12 mm thick with cement mortar 1:3 ( 1 cement :3 coarse sand ) finished with floating coat of neat cement & making channels in cement concrete 1:2:4 ( 1 cement : 2 coasre sand :4 graded stone aggragate 20mm nominal size ) finished with a floating coat of neat cement complete as per standard design. Inside size 90 x 80 cm & 45cm deep including providing and fixing in position precast RCC manhole cover & frame of required shape and approved quanlity LD-2.5 rectangular shape 600x450 mm internal dimensions . With F.P.S bricks with class designation 75 & with crushed stone aggregate including all leads, lifts & carriage of material by MT / H.L.

Providing & fixing unplasticised PVC connection pipe with brass unions30 cm length 15 mm nominal bore

Providing and Fixing of Jet of good quality

Providing and fixing 600 x450 mm bevelled Edge Mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing ball valve ( brass) of approved quality complete high or low pressure with plastic floats

15 mm nominal bore

20 mm nominal bore

Providing and fixing PVC waste pipe for sink or wash basin including PVC waste fitting complete semi rigid pipe 32 mm dia

Providing and fixing Soap Dish of approved quality.

Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200mm wide with a minimum distance of 37 mm from wall face with concealed fittings arrangements of approved quality and colour, weighing not less than 88 gms.

Providing and fixing PTMP grating of approved quality and colour. Circular Type

100 mm nominal dia

125 mm nominal dia with 25 mm waste hole

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade. New work (two or more coats) over and including priming coat with cement primer.

Finishing wall with water proofing cement paint of required shade -New work (two or More coats) applied @ 3.84 kg/ 10 sqm

Rajesh Kumar

M/S SANTOSH KUMARI

ANWAR CHOUDHARY GOVT CONTRACTOR

TARSEM CHAND

kiran kumar

M/S SUDHANSHU GUPTA GOVT CONTRACTOR