Construction of Commercial Building in Parshuram Asthan Campus under Nagar Parishad Mokama

Clearing jungle including uprooting or rank vegetation, grass, brush wood, trees and scaplings of girth upto 30 cm measured at a height of 1 m above ground level and removal of rubbish upto a distance of 50 m outside the periphery of the area cleared.

Earth work in excavation in foundation trenches or drains(not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m . including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m

All kinds of soil

Filling available excavated earth (exclude rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth consolidating each oeposited layer by ramming and watering lead.Ali kinds of soil

Brick work with bricks of class designation 100A in foundation and plinth in:

cement mortar 1:6 (1 cement : 6 coarse sand)

Brick work in superstructure above plinth level upto floor V

Half brick masonry with brick of class designation 100A in foundation and plinth.

Brick work with fly ash bricks as per IS 12894(2002) & IS 3495 in foundations and plinth in :

Cement mortar 1:6 (1 cement: 6 coarse sand ) - 250 mm th Brick work

Providing designation 100 A one brick flat soling joints filled with local sand including cost of watering, taxes, royalty all complete as per building specification and direction of E/l,

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shutering-all work upto plinth level.

1:3:6 (1 Cement; 3 coarse sand :6 graded stone aggregate 20 mm nominal size)

Providing and laying damp-proof Course 50 mm thick with cement concrete 1:2:4(1cement:2:2 coarse sand :4 graded stone aggregate 20mm nominal size)

Extra for providing and mixing water prooding material in cement concrete work in the proportion recommended by the manufacturers.

Providing and laying in position ready mixed concrete manufactured in fully automatic batching plant and transported to site of work in transit mixer for a lead up to 10kms having continuous agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work including pumping of R.M.C. from transit mixer to site of laying , excluding the cost of centering, shuttering finishing and reinforcement including cost of admixtures in recommended proportions as per IS : 9103 to accelerate/ retard setting of concrete, improve workability without impairing strength and durability as per direction of the Engineer - in - charge. M-25 grade Reinforced cement concrete by using 330 kg of cement per cum of concrete.

All work from plinth level upto floor V level

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work upto plinth level.

Reinforced cement conrete work in beams,suspended floors, roofs having slope upto 15, landings,balconiec, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto floor five level excludingthe cost of centring, shuttering, finishing and reinforement with 1:2:4(1 cement:2 coarse sand:4 graded stone aggregate 20 mm nominalsize). Providing M-15grade R.C.C instead of M-20 grade R.C.C.

Centring and shuttering including strutting, propping etc. and removal of form for:

Columns, piers.abutments, pillars,posts and struts

Thermo-Mechanically Treated bars TMTC-500-8mm dia

Thermo-Mechanically Treated bars TMTC-500-10mm dia

Thermo-Mechanically Treated bars TMTC-500-12mm dia

Thermo-Mechanically Treated bars TMT Fe-500- 16mm dia

12 mm cement plaster 1:3( 1 cement: 3 coarse sand) finished with a floating coat of near cement

12mm cement plaster of mix:

15mm cement plaster of mix :

Providing 12 mm cement plaster of mix of CM 1:3 (1 cement:3 coarse sand) With Neat cement punning etc.

Providing 12 mm cement plaster of mix of CM 1:3 (1 cement:3 coarse sand)

Providing and fixing factory made single extruded WPC {Wood Polymer Composite} solid plain flush door shutter of required size comprising of virgin polymer of K value 58-60 Suspension Grade), calcium carbonate and natural fibers {wood powder/ rice husk/wheat husk) and non toxic additives {maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800N {Face) & 900N (Edge), minimum compressive strength 50 N/mm, modulus of elasticity 850 N/mm and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In• Charge. {Note: stainless steel butt hinges and necessary S.S screws shall be paid separately)

Providing and fixing alluminium handles anodised(anodic coating not less than grade AC 10 as per IS :1868) transparent or dyed to required colour and shade with necessary screws etc. complete:

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size,approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups,including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.

Extra for providing opening of required size & shape for wash basins / kitchen sink in kitchen platform, vanity counters and similar location in marble/stone work including necessary holes for pillar taps etc. including rubbing and polishing of cut edges etc. complete.

Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS:15622 (thickness to be specified by the manufacture) of approved make in all colours, shades except begundy, bottle green,black of any size as approved by Engineer-in-chage in skirting, risers of steps and dados over 12mm thick bed of Cement Mortar 1:3 (1 Cement:3 Coarse sand ) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete.

Kota stone slab flooring over 20mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete.

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade.

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.

New work (Two or more coats applied @ 3.28 ltr/ 10 sqm) over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm

Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications.

Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of special primer applied @ 0.75 ltr /10 sqm.

Steel work welded in built up sections/framed worK including cutting hoisting, rixing in position and applying a priming coat of approved steel primer using structural steel, etc. as required.

Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade

New work (Two or more coats applied @ 1.43 ltr/ 10 sqm.over and including base coat of water proofing cement paint applied @ 2.20 kg/ 10 sqm).

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement:2 coarse sand:4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 mx1 mx400 micron, finished 12 mm cement plaster 1:3 (1 cement:3 coarse sand) and a coat of neat cement rounding the edges and making and finishing the outlet complete

Providing and laying APP (Atactic Polypropylene Polymer) modified prefabricated five layer 3mm thick water proofing membrane, black finished reinforced with non-woven polyester matt consisting of a coat of bitumen primer for bitumen membrane @ 0.40 ltr/sqm. by the same membrane manufacture of density at 25°C, 0.87-0.89 kg/ltr and viscocity 70-160 cps. Over the primer coat the layer of membrane shall be laid using Butane Torch and sealing all joints etc., and preparing the surface complete. The vital physical and chemical parameters of the membrane shall be as under : Joint strength in longitudinal and transverse direction at 23°C as 650/450N/5cm. Tear strength in longitudinal and transverse direction as 300/250N. Softening point of membrane not less than 150°C. Cold flexibility shall be upto -2°C when tested in accordance with ASTM, D - 5147. The laying of membrane shall be got done through the authorised applicator of the manufacturer of membrane :

Extra for covering top of membrane with Geotextile, 120 gsm non woven, 100%polyester of thickness 1 to 1.25 mm bonded to the membrane with intermittent touch by heating the membrane by Butane Torch as per manufactures recommendation.

Along external wall where the apron is not provided using chemical imulsion @ 7.5 liters / sqm of the vertical surface of the substructure to a depth of 300 mm including excavation channel along the wall & rodding etc. complete:

Boring, providing and installing bored cast-in-situ reinforced cement concrete piles of grade M-25 of specified diameter and length below the pile cap, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring, with bentonite solution and temporary casing of appropriate length for setting out and removal of same and the length of the pile to be embedded in the pile cap etc. all complete, including removal of excavated earth with all lifts and leads (Length of pile for payment shall be measured upto bottom of pile cap). 300 mm dia piles

Constructing brick masonry chamber for underground C.I. inspection chamber and bends with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions

Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design.

Boring/drilling bore well of required dia for casing/ strainer pipe by suitable method 300mm dia etc all complete job as per building specification & direction of E/I.

Supplying assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well casing (CM) pipe of required 150mm dia etc all complete job as per building specification & direction of E/I.

Supplying assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipe of required 150mm dia etc all complete job as per building specification & direction of E/I.

Gravel packing in tubewell construction in accordance with IS:4097 including providing gravel line/medium /coarse in required grading and sizes etc all complete job as per building specification & direction of E/I.

Development of tube well in accordance with IS : 2800 (part I) and IS: 11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully develo ped, measuring yield of well by "V" notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, i/c disinfection of tubewell, all complete,including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge.

Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/casing pipe 150mm dia etc all complete job as per building specification & direction of E/I.

Providing and fixing M.S. clamp of required dia to the top of casing/housing pipe of tubewell 150mm dia etc all complete job as per building specification & direction of E/I.

Providing and fixing bail plug/bottom plug of required dia to the bottom of pipe assembly of tubewell as per IS:2800 (Part_1) 150mm dia etc all complete job as per building specification & direction of E/I.

Supplying, assembling, lowering and fixing in vertical position in bore well, ERW (Electric Resistance Welded) FE 410 plain slotted (having slot of size 1.6/3.2 mm) mild steel threaded and socketed / plain bevel ended pipe (type A) of required dia, conforming to IS: 8110, of reputed and approved make, having wall thickness not less than 5.40 mm, including painted with outside surface with two coats of anticorrosive bitumestic paint of approved brand and manufacture,including hire & labour charges, fittings & accessories, all complete,for all depths, as per direction ofEngineer -in-charge.

Supplying one H.P. Cromoton gravel submersible pump strainer with all accossories for running condition etc all complete job as per building specification & direction of E/I.

Brick work with bricks of class designation 100A in foundations and plinth in :Cement mortar 1 : 4 (1 cement: 4 coarse sand )

Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centring,shuttering,finishing and reinforcement-All work puto plinth level 1:1:5:3(1 cement: 1.5 coarse sand:3 graded stone aggregate 20 mm nominal size)

Supplying brick bat for filling in recharge pit etc all complete job.

12 mm cement plaster 1:3( 1 cement: 3 coarse sand) finished with a floating coat of near cement

(iii) Rate per cum for grading-III Material

Plain/Reinfoced Cement concrete in open foundation complete as per drawing and technical specifications of grade M25 by manual placing

Supplying, Fitting and Placing un-coated HYSD bar Reinforcement in Foundation complete as per Drawing and Technical Specifications.

Providing and laying in position cement concrete of specified grade exluding the cost of centring and shuttering-all work upto plinth level.1:1.5:3(1 Cement :1.5 coarse sand:3 graded stone aggregate 20 mm nominal size)

Providing and laying factory made chamfered edge Cement Concrete paver blocks In foot path, park & lawns driveway or light & traffic parking etc. of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of course sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand, all complete as per manufacturer's specifications & direction of Engineer- in-Charge.

Flexible Median Marker (FMM) as per IRC 79:2019 Supplying and Installation of Flexible Median Marker made up of plastic body moulded from flexible thermoplastic.Flexible Median Marker (FMM) should be used for improving median visibility during dark hours, Use of Median Marker provides safety against collision happening wih median during night time, or severe weather. Flexible Median Markers shall be provided with fluorescent yellow colour retro-reflective sheeting Type XI as per IRC 67, Flexible Median Marker shall be of tough, high impact resistant, injection-molded, thermoplastic body with property of flexibility to provide high durability and U shape structure having rebound/ bounce back property. The sheeting shall be of Type XI conforming to IRC:67 and it should be on both the faces whereby providing minimum reflectivity at longer distances with adequate durability. The logo of the manufacturer shall be embossed on either side of the body during the injection moulding process. FMM shall be fixed by a combination of epoxy adhesive and grouting/drilling on concrete medians or properly constructed solid medians. Height :The marker height shall be a minimum of 180 mm, width 120 mm & Body thickness 6.5 mm. The shank shall not be less than 20 mm and depth shall not be less than 30 mm, Reflective Area: Shall not be less than 90 cm square. Proof of the same report shall be uploaded while quoting tender. The body of FMM shall bounce back to its original position of after 750 number of hits using pendulum of 1.8 kg conforming 40 ASTM D256 adhesion between the body and outer casting body of FMM shall withstand 50 kgf tensile loads conforming to ASTM D638 method.

Design engineering manufacturing transport supply errection commissioning ant testing of complete high mast lighting system with rising and lowering mechanism,power tolls motor,feeder pillar,push button station with all accessories to maintain a required lux level including 25 meter height

Supply and erection of 6 metre height Hot-dip galvanized octagonal street light pole with following arm with top dia 70 mm and bottom dia A/F 130 mm, made of 3 mm thick sheet along with base plate of size 220 x 220 x 12 mm, small door opening for junction box mounting with MCB & connector, cement concrete of 1:3:6 including excavation, fefilling and suitable size foundation bolts with template and all complete job as required. (but without pole collar)

Single arm, 1500 mm

Supplying and fixing following LED street/Flood light with die cast aluminium housing for ingress protection of IP65 and complete with all accessories etc on pole/building including connection and earthing the body etc. as required.

65/70 watt Street light

Supplying and drawing following sizes of FR PVC insulated copper conductor, single core cable in the existing surface/recessed PVC conduit as reqd.

3 x 4 sq. mm

Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc conforming to IS 14930 part II complete with fitting and cutting jointing etc in the existing trench, complete as req

63mm dia (OD-63mm & ID-51 mm nominal)

Supplying and drawing following sizes of FR PVC insulated copper conductor, single core cable in the existing surface/recessed PVC conduit as reqd.

2 x 1.5 sq. mm

Providing and fixing lightning conductor finial, made of 25 mm dia 300 mm long, G.I. tube, having single prong on top, with 85 mm dia 6 mm thick G.I. base plate including holes etc. complete as reqd.

Jointing copper/G.I. tape (with another copper/GI tape, base of the finial or any other metallic object) by riverting/nut bolting sweating and soldering etc. as reqd.

Providing and fixing G.I. tape 20 mm x 3 mm thick on parapet or surface of wall for lightning conductor complete as required. (for horizontal run)

Providing and fixing G.I. tape 20 mm x 3 mm thick on parapet or surface of wall for lightning conductor complete as required. (for vertical run)

Providing and fixing testing joint, made of 20 mm x 3 mm thick copper strip, 125 mm long, with 4 nos. of tinned brass bolts, nuts, chuk nuts and spring washers etc. complete as reqd.

Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/coke and salt as required.

Supplying and laying 25mm x 5mm G.I. strip in 40 mm dia G.I. pipe from earth electrode, including connection with G.I. nut, bolt, spring, washer excavation and refilling etc. as reqd.

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.

Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point (without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required.

Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface /recessed medium class PVC conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providng and fixing 2 Nos. 3 pin 5/6 A modular socket outlet and 2 Nos. 5/6 A modular switch, connections etc. as required. (For light plugs to be used in non residential buildings).

Supplying and fixing Stepped type modular Fan regulator, (2 module)

Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

5 pin 5/6 amps, modular socket outlet, ISI marked

S.P. 5/6 amps, one way modular switch, ISI marked

Supplying and fixing 6 pin 15/16 amps, modular socket outlet, ISI marked

S.P. 15/16 amps, one way modular switch, ISI marked

Supplying & fixing suitable size GI box wih modular plate and cover in front on surface or in recess including providing and fixing 25 A modular socket outlet and 25 A modular SP MCB, “C” curve including connections, painting etc. as required.

Modular GI box for 2 module

Modular GI box for 4 module

Modular base & cover plate for 2 module

Modular base & cover plate for 4 module

Supplying and fixing following 4 way (4+12) TPN MCB DB, double door, horizontal testing and commissioning etc. as required.

Supplying and fixing following 8 way (4+24) TPN MCB DB, double door, horizontal type testing and commissioning etc. as required.

Supplying and fixing Blanking plate, single pole etc. as required.

Providing and fixing M.V. danger notice plate of 200 mm X 150 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required.

Supplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc. as required.

Supplying and installing following size of perforated painted with powder coating M.S. cable trays bends with perforation not more than 17.5%,, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc. as required.

Supplying and installing following size of perforated painted with powder coating M.S. cable trays Tee with perforation not more than 17.5%, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc. as required.

Supplying and installing following size of perforated painted with powder coating M.S. cable trays Reducer with perforation not more than 17.5%, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc. as required.

Supplying and drawing co-axial TV cable RG-6 grade

Recess mounted 12 watt LED downlighter complete with all accessories and replaceable electronic driver

Recess mounted 18 watt LED downlighter complete with all accessories and replaceable electronic driver

Single powder coated batten suitable for 1X28 watt T5 lamp complete with electronic ballast etc. MIRROR LIGHT

450 mm, 230V, A.C. exhaust fan

Regular/standard make 1200 mm sweep ceiling fan.

Surface mounted 15/18 watt LED downlighter complete with all accessories and replaceable electronic driver

wall bracket fixture in chrome finish with glass diffuser suitable for single 15 watt CFL/LED lamp

Bulk Head fitting with aluminium alloy body and prismatic glass cover suitable for CFL/ GLS lamp

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. as required.

Providing and fixing earth bus of 50 mm X 5 mm copper strip on surface for connections etc. as required.

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/submain wiring/ cable as required.

S I T C of star rated Aluminium wound distribution Transformer of following rating 11/0.433KV Delta-Star Connected, Vector Group Dyn 11,ONAN Cooled & as per BEE star - 1 & BIS approved as per IS 2026- 1977 & losses as defined as per 2014 (Fourth Revision) Level-1 . including standard accessories like conservator, silica gel breather, radiator, fins, HT cable box & LT cable boxes, temperature rise in winding/oil 35-40 degree C first filling of transformer oil as per IS :335-1953, Epoxy based paint, including carrying of pre-commission Testing & Charging of Transformer complete in all respect .

3.5 core, 240 sq. mm XLPE/PVC insulated sheathed (Heavy duty) armoured electric cable with aluminium conductor

Providing & fixing of Vitreous china pedestal type water closet testing and commissioning etc. as required.

Providing & fixing of Cistern with fittings for Waterless Urinal testing and commissioning etc. as required.

Providing & fixing of Vitreous china Surgeon type wash basin of size 660x460 mm testing and commissioning etc. as required.

Providing & fixing of PTMT - Liquid Soap Container of 400 ml capacity

Providing and fixing of PTMT - Towel Ring 215x200x37 mm

Providing & fixing of PTMT - Soap Dish/Holder 138x102x75 mm

Rectangular shape 453x357 mm Mirror with Plastic moulded frame

Providing & fixing of C.P. Brass long body bibcock 15 mm testing and commissioning etc. as required.

C.P.brass toilet paper holder of standard size

PTMT - Bottle Trap 31/32 mm

PTMT - Bottle Trap 38/40 mm

Providing and fixing of C.P. Brass angle valve 15 mm testing and commissioning etc. as required.

Providing and fixing of C.P. Brass Extension Nipple (1/2"x2" size) testing and commissioning etc. as required.

Providing and fixing of 15 mm nominal bore and 45 cm length PVC connection pipe with P.T.M.T. Nuts testing and commissioning etc. as required.

PTMT grating 100 mm dia

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete.

Cutting holes up to 15x15 cm in R.C.C. floors and roofs for passing drain pipe etc. and repairing the hole after insertion of drain pipe etc. with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including finishing complete so as to make it leak proof.

15 mm nominal outer dia Pipes

20 mm nominal outer dia Pipes

25 mm nominal outer dia Pipes

32 mm nominal outer dia Pipes

40 mm nominal outer dia Pipes

H.P. or L.P. ball valve with polythene floats: 25 mm dia

Painting G.I. pipes and fittings with two coats of anti-corrosive bitumastic paint of approved quality.

Providing and placing on terrace Polyethylene water storage tank with cover and suitable locking arrangement

i) Local Sand

(ii) Coarse Sand

(iii)Stone Chips

iv) Bricks

v) Cement

vi) Paver Block

vii) GSB

a) Bricks

b)Cement

BCD/SOR- 2022

Clearing jungle including uprooting or rank vegetation, grass, brush wood, trees and scaplings of girth upto 30 cm measured at a height of 1 m above ground level and removal of rubbish upto a distance of 50 m outside the periphery of the area cleared.

Earth work in excavation in foundation trenches or drains (not exceeding 1.5m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.

All kinds of soil

MASONRY WORK

Brick work in superstructure above plinth level upto floor V

Half brick masonry with brick of class designation 100A in foundation and plinth.

Brick work with fly ash bricks as per IS 12894(2002) & IS 3495 in foundations and plinth in :

Cement mortar 1:6 (1 cement: 6 coarse sand ) - 250 mm th Brick work

Providing designation 100 A one brick flat soling joints filled with local sand including cost of watering, taxes, royalty all complete as per building specification and direction of E/l,

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shutering-all work upto plinth level.

1:3:6 (1 Cement; 3 coarse sand :6 graded stone aggregate 20 mm nominal size)

Providing and laying damp-proof Course 50 mm thick with cement concrete 1:2:4(1cement:2:2 coarse sand :4 graded stone aggregate 20mm nominal size)

Extra for providing and mixing water prooding material in cement concrete work in the proportion recommended by the manufacturers.

Providing and laying in position ready mixed concrete manufactured in fully automatic batching plant and transported to site of work in transit mixer for a lead up to 10kms having continuous agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work including pumping of R.M.C. from transit mixer to site of laying , excluding the cost of centering, shuttering finishing and reinforcement including cost of admixtures in recommended proportions as per IS : 9103 to accelerate/ retard setting of concrete, improve workability without impairing strength and durability as per direction of the Engineer - in - charge. M-25 grade Reinforced cement concrete by using 330 kg of cement per cum of concrete.

All work upto plinth level

All work from plinth level upto floor V level

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work upto plinth level.

1:1.5:3(1 Cement :1.5 coarse sand:3 graded stone aggregate 20 mm nominal size)

Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centering,shuttering,finishing and reinforcement-All work puto plinth leve

Reinforced cement conrete work in beams,suspended floors, roofs having slope upto 15, landings,balconiec, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto floor five level excludingthe cost of centring, shuttering, finishing and reinforement with 1:2:4(1 cement:2 coarse sand:4 graded stone aggregate 20 mm nominalsize). Providing M-15grade R.C.C instead of M-20 grade R.C.C.

Centring and shuttering including strutting, propping etc. and removal of form for:

Foundations,footings, bases Columns

Columns, piers.abutments, pillars,posts and struts

Thermo-Mechanically Treated bars TMTC-500-8mm dia

Thermo-Mechanically Treated bars TMT Fe-500- 16mm dia

FINISHING WORK

Providing 12 mm cement plaster of mix of CM 1:3 (1 cement:3 coarse sand)

Providing and fixing factory made single extruded WPC {Wood Polymer Composite} solid plain flush door shutter of required size comprising of virgin polymer of K value 58-60 Suspension Grade), calcium carbonate and natural fibers {wood powder/ rice husk/wheat husk) and non toxic additives {maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800N {Face) & 900N (Edge), minimum compressive strength 50 N/mm, modulus of elasticity 850 N/mm and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In• Charge. {Note: stainless steel butt hinges and necessary S.S screws shall be paid separately)

35 mm thick

Providing and fixing alluminium handles anodised(anodic coating not less than grade AC 10 as per IS :1868) transparent or dyed to required colour and shade with necessary screws etc. complete:

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size,approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups,including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.

Extra for providing opening of required size & shape for wash basins / kitchen sink in kitchen platform, vanity counters and similar location in marble/stone work including necessary holes for pillar taps etc. including rubbing and polishing of cut edges etc. complete.

Kota stone slab flooring over 20mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete.

20 to 25mm thick

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade.

Two or more coat on new surface.

Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade

New work (Two or more coats applied @ 1.43 ltr/ 10 sqm.over and including base coat of water proofing cement paint applied @ 2.20 kg/ 10 sqm).

Providing and laying APP (Atactic Polypropylene Polymer) modified prefabricated five layer 3mm thick water proofing membrane, black finished reinforced with non-woven polyester matt consisting of a coat of bitumen primer for bitumen membrane @ 0.40 ltr/sqm. by the same membrane manufacture of density at 25°C, 0.87-0.89 kg/ltr and viscocity 70-160 cps. Over the primer coat the layer of membrane shall be laid using Butane Torch and sealing all joints etc., and preparing the surface complete. The vital physical and chemical parameters of the membrane shall be as under : Joint strength in longitudinal and transverse direction at 23°C as 650/450N/5cm. Tear strength in longitudinal and transverse direction as 300/250N. Softening point of membrane not less than 150°C. Cold flexibility shall be upto -2°C when tested in accordance with ASTM, D - 5147. The laying of membrane shall be got done through the authorised applicator of the manufacturer of membrane :

Extra for covering top of membrane with Geotextile, 120 gsm non woven, 100%polyester of thickness 1 to 1.25 mm bonded to the membrane with intermittent touch by heating the membrane by Butane Torch as per manufactures recommendation.

Extra for covering top of membrane with Geotextile, 120 gsm non woven, 100%polyester of thickness 1 to 1.25 mm bonded to the membrane with intermittent touch by heating the membrane by Butane Torch as per manufactures recommendation.

BCD/SOR- 2022

Clearing jungle including uprooting or rank vegetation, grass, brush wood, trees and scaplings of girth upto 30 cm measured at a height of 1 m above ground level and removal of rubbish upto a distance of 50 m outside the periphery of the area cleared.

Earth work in excavation in foundation trenches or drains (not exceeding 1.5m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.

All kinds of soil

Earth work in excavation in foundation trenches or drains (not exceeding 1.5m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.

All kinds of soil

Earth work in excavation in foundation trenches or drains(not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m . including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m

All kinds of soil

Filling available excavated earth (exclude rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth consolidating each oeposited layer by ramming and watering lead.Ali kinds of soil

Filling available excavated earth (exclude rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth consolidating each oeposited layer by ramming and watering lead.Ali kinds of soil

Supplying and filling in plinth with local sand under floors including, watering, ramming consolidating and dressing complete.

Supplying and filling in plinth with local sand and under floors including, watering, ramming consolidating and dressing complete.

Supplying and filling in plinth with local sand under floors including, watering, ramming consolidating and dressing complete.

Brick work with bricks of class designation 100A in foundation and plinth in:

cement mortar 1:6 (1 cement : 6 coarse sand)

Brick work in superstructure above plinth level upto floor V

Half brick masonry with brick of class designation 100A in foundation and plinth.

Cement mortar 1:6 (1 cement: 6 coarse sand ) - 250 mm th Brick work

Providing designation 100 A one brick flat soling joints filled with local sand including cost of watering, taxes, royalty all complete as per building specification and direction of E/l,

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shutering-all work upto plinth level.

1:3:6 (1 Cement; 3 coarse sand :6 graded stone aggregate 20 mm nominal size)

1:3:6 (1 Cement; 3 coarse sand :6 graded stone aggregate 20 mm nominal size)

Providing and laying damp-proof Course 50 mm thick with cement concrete 1:2:4(1cement:2:2 coarse sand :4 graded stone aggregate 20mm nominal size)

Extra for providing and mixing water prooding material in cement concrete work in the proportion recommended by the manufacturers.

Providing and laying in position ready mixed concrete manufactured in fully automatic batching plant and transported to site of work in transit mixer for a lead up to 10kms having continuous agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work including pumping of R.M.C. from transit mixer to site of laying , excluding the cost of centering, shuttering finishing and reinforcement including cost of admixtures in recommended proportions as per IS : 9103 to accelerate/ retard setting of concrete, improve workability without impairing strength and durability as per direction of the Engineer - in - charge. M-25 grade Reinforced cement concrete by using 330 kg of cement per cum of concrete.

All work upto plinth level

All work from plinth level upto floor V level

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work upto plinth level.

1:1.5:3(1 Cement :1.5 coarse sand:3 graded stone aggregate 20 mm nominal size)

Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centering,shuttering,finishing and reinforcement-All work puto plinth leve

Reinforced cement conrete work in beams,suspended floors, roofs having slope upto 15, landings,balconiec, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto floor five level excludingthe cost of centring, shuttering, finishing and reinforement with 1:2:4(1 cement:2 coarse sand:4 graded stone aggregate 20 mm nominalsize). Providing M-15grade R.C.C instead of M-20 grade R.C.C.

Centring and shuttering including strutting, propping etc. and removal of form for:

Foundations,footings, bases Columns

Columns, piers.abutments, pillars,posts and struts

Reinforcement for R.C.C work including straighting,cutting bending,Placing in position and binding all complets.

FINISHING WORK

Providing 12 mm cement plaster of mix of CM 1:3 (1 cement:3 coarse sand) With Neat cement punning etc.

Providing 12 mm cement plaster of mix of CM 1:3 (1 cement:3 coarse sand)

WOOD & ALUMINIUM WORK

STONE WORK

Granite black

FLOORING WORK

WATER PROOFING WORK

Along external wall where the apron is not provided using chemical imulsion @ 7.5 liters / sqm of the vertical surface of the substructure to a depth of 300 mm including excavation channel along the wall & rodding etc. complete:

Constructing brick masonry chamber for underground C.I. inspection chamber and bends with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions

Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design.

Boring/drilling bore well of required dia for casing/ strainer pipe by suitable method 300mm dia etc all complete job as per building specification & direction of E/I.

Supplying assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well casing (CM) pipe of required 150mm dia etc all complete job as per building specification & direction of E/I.

Supplying assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipe of required 150mm dia etc all complete job as per building specification & direction of E/I.

Gravel packing in tubewell construction in accordance with IS:4097 including providing gravel line/medium /coarse in required grading and sizes etc all complete job as per building specification & direction of E/I.

Development of tube well in accordance with IS : 2800 (part I) and IS: 11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully develo ped, measuring yield of well by "V" notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, i/c disinfection of tubewell, all complete,including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge.

Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/casing pipe 150mm dia etc all complete job as per building specification & direction of E/I.

Providing and fixing M.S. clamp of required dia to the top of casing/housing pipe of tubewell 150mm dia etc all complete job as per building specification & direction of E/I.

Providing and fixing bail plug/bottom plug of required dia to the bottom of pipe assembly of tubewell as per IS:2800 (Part_1) 150mm dia etc all complete job as per building specification & direction of E/I.

Supplying, assembling, lowering and fixing in vertical position in bore well, ERW (Electric Resistance Welded) FE 410 plain slotted (having slot of size 1.6/3.2 mm) mild steel threaded and socketed / plain bevel ended pipe (type A) of required dia, conforming to IS: 8110, of reputed and approved make, having wall thickness not less than 5.40 mm, including painted with outside surface with two coats of anticorrosive bitumestic paint of approved brand and manufacture,including hire & labour charges, fittings & accessories, all complete,for all depths, as per direction ofEngineer -in-charge.

Supplying one H.P. Cromoton gravel submersible pump strainer with all accossories for running condition etc all complete job as per building specification & direction of E/I.

Brick work with bricks of class designation 100A in foundations and plinth in :Cement mortar 1 : 4 (1 cement: 4 coarse sand )

Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centring,shuttering,finishing and reinforcement-All work puto plinth level 1:1:5:3(1 cement: 1.5 coarse sand:3 graded stone aggregate 20 mm nominal size)

Supplying brick bat for filling in recharge pit etc all complete job.

12 mm cement plaster 1:3( 1 cement: 3 coarse sand) finished with a floating coat of near cement

(iii) Rate per cum for grading-III Material

Plain/Reinfoced Cement concrete in open foundation complete as per drawing and technical specifications of grade M25 by manual placing

Supplying, Fitting and Placing un-coated HYSD bar Reinforcement in Foundation complete as per Drawing and Technical Specifications.

Providing and laying in position cement concrete of specified grade exluding the cost of centring and shuttering-all work upto plinth level.1:1.5:3(1 Cement :1.5 coarse sand:3 graded stone aggregate 20 mm nominal size)

Providing and laying factory made chamfered edge Cement Concrete paver blocks In foot path, park & lawns driveway or light & traffic parking etc. of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of course sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand, all complete as per manufacturer's specifications & direction of Engineer- in-Charge.

Flexible Median Marker (FMM) as per IRC 79:2019 Supplying and Installation of Flexible Median Marker made up of plastic body moulded from flexible thermoplastic.Flexible Median Marker (FMM) should be used for improving median visibility during dark hours, Use of Median Marker provides safety against collision happening wih median during night time, or severe weather. Flexible Median Markers shall be provided with fluorescent yellow colour retro-reflective sheeting Type XI as per IRC 67, Flexible Median Marker shall be of tough, high impact resistant, injection-molded, thermoplastic body with property of flexibility to provide high durability and U shape structure having rebound/ bounce back property. The sheeting shall be of Type XI conforming to IRC:67 and it should be on both the faces whereby providing minimum reflectivity at longer distances with adequate durability. The logo of the manufacturer shall be embossed on either side of the body during the injection moulding process. FMM shall be fixed by a combination of epoxy adhesive and grouting/drilling on concrete medians or properly constructed solid medians. Height :The marker height shall be a minimum of 180 mm, width 120 mm & Body thickness 6.5 mm. The shank shall not be less than 20 mm and depth shall not be less than 30 mm, Reflective Area: Shall not be less than 90 cm square. Proof of the same report shall be uploaded while quoting tender. The body of FMM shall bounce back to its original position of after 750 number of hits using pendulum of 1.8 kg conforming 40 ASTM D256 adhesion between the body and outer casting body of FMM shall withstand 50 kgf tensile loads conforming to ASTM D638 method.

Design engineering manufacturing transport supply errection commissioning ant testing of complete high mast lighting system with rising and lowering mechanism,power tolls motor,feeder pillar,push button station with all accessories to maintain a required lux level including 25 meter height

Supply and erection of 6 metre height Hot-dip galvanized octagonal street light pole with following arm with top dia 70 mm and bottom dia A/F 130 mm, made of 3 mm thick sheet along with base plate of size 220 x 220 x 12 mm, small door opening for junction box mounting with MCB & connector, cement concrete of 1:3:6 including excavation, fefilling and suitable size foundation bolts with template and all complete job as required. (but without pole collar)

Single arm, 1500 mm

Supplying and fixing following LED street/Flood light with die cast aluminium housing for ingress protection of IP65 and complete with all accessories etc on pole/building including connection and earthing the body etc. as required.

65/70 watt Street light

Supplying and drawing following sizes of FR PVC insulated copper conductor, single core cable in the existing surface/recessed PVC conduit as reqd.

3 x 4 sq. mm

Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc conforming to IS 14930 part II complete with fitting and cutting jointing etc in the existing trench, complete as req

63mm dia (OD-63mm & ID-51 mm nominal)

Supplying and drawing following sizes of FR PVC insulated copper conductor, single core cable in the existing surface/recessed PVC conduit as reqd.

2 x 1.5 sq. mm

Providing and fixing lightning conductor finial, made of 25 mm dia 300 mm long, G.I. tube, having single prong on top, with 85 mm dia 6 mm thick G.I. base plate including holes etc. complete as reqd.

Jointing copper/G.I. tape (with another copper/GI tape, base of the finial or any other metallic object) by riverting/nut bolting sweating and soldering etc. as reqd.

Providing and fixing G.I. tape 20 mm x 3 mm thick on parapet or surface of wall for lightning conductor complete as required. (for horizontal run)

Providing and fixing G.I. tape 20 mm x 3 mm thick on parapet or surface of wall for lightning conductor complete as required. (for vertical run)

Providing and fixing testing joint, made of 20 mm x 3 mm thick copper strip, 125 mm long, with 4 nos. of tinned brass bolts, nuts, chuk nuts and spring washers etc. complete as reqd.

Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/coke and salt as required.

Supplying and laying 25mm x 5mm G.I. strip in 40 mm dia G.I. pipe from earth electrode, including connection with G.I. nut, bolt, spring, washer excavation and refilling etc. as reqd.

PVC INSULATED COPPER CONDUCTOR WIRES

Supplying and fixing following 4 way (4+12) TPN MCB DB, double door, horizontal testing and commissioning etc. as required.

Supplying and fixing 6 amps. To 32 amps ratings, SP MCB, "C" curve testing and commissioning etc. as required.

Supplying and fixing following rating, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing following rating, double pole, (single phase and neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing of following sizes of medium class PVC conduit

Supply, fixing, connecting and testing of telephone/computer/TV modular sockets connectionetc as required.

Providing, fixing connecting and testing of solder less Television Junction Box of following capacity ties as required in suitable size of m.s. hinged lockable cover box duly painted etc. as required of Krone type.

Supplying and fixing metal box for tele tag box

Providing and fixing PTMT Bottle Trap for Wash basin and sink.testing and commissioning etc. as required.

Subhead:- II - Internal Drainage (Rainwater, Soil, Waste & Fittings)

Providing & fixing PTMT grating of approved quality and colour

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,

Providing and fixing G.I. Pipes complete with G.I. fittings and clamps,including cutting and making good the walls etc.(in Terrace)

Providing & fixing ball valve ( brass) of approved quality,High or low pressure, with plastic floats complete:-

Providing and fixing G.I. Union in existing G.I. pipe line, cutting and threading the pipe and making long screws, including excavation, refilling the earth or cutting of wall and making good the same complete wherever required :

Providing and fixing enclosed type water meter

Typical Specification Basis

1. King Size Bed with 2. side tables

Mattress with protectors and bed sheet set

2 seater sofaw/coffee table

Lounge chair

TV unit

Upholstered Wall Pan

42'' Led Tv

Intercom

False Ceiling

Wardrobe

curtains

1 single bed

Mattress with protectors and bed sheet set

Coffee Table with Chair

TV unit

Upholstered Wall Pan

42'' Led Tv

Intercom

False Ceiling

Wardrobe

curtains

Acousticsal Wall cladding

False Ceiling

Conference Table

Round tables

chairs

Storage Cabinets (1.52m x 0.91 m)

wall cladding

False Ceiling

Reception Desk

chairs

Storage Cabinets (1.52m x 0.91 m)

wall cladding

False Ceiling

Single Sofa

Chairs

Centre table