Development of Ribandar Community Market under Smart Cities Mission

Amount

Dismantling the tile work in floors and roofs laid in cement including stacking of materials within 50 meters lead for thickness of tiles 10mm to 25mm.

Demolishing cement concrete 1:3:6 or richer mix including disposal of material with in 50 meter lead as per direction of Engineer.

Dismantling precast concrete or stone slabs etc. including stacking within 50 meters lead. Thickness above 38mm and up to 75mm

Demolishing laterite stone masonry in cement mortar including stacking of serviceable material & disposal of unserviceable material within 50 mts. lead.

Dismantling and removing Mangalore roofing tiles from roofs including ridges, hips, valleys, sheets wind ties etc. but excluding battens, roof timber etc. and stacking materials within a distance of 50 rm.

Dismantling wooden trellis work in position excluding frames but including stacking the serviceable material within 50 meters lead.

Clearing grass and removal of rubbish up to a distance of 50 m outside the periphery of the area

Earthwork in excavation by mechanical means (hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sq.m on plan) including disposal of excavated earth lead up to 50 m and lift up to 1.5m disposed earth to be levelled and neatly dressed including providing barricading, danger lighting guarding as directed in : a: All kinds of soil

Boring holes vertically true to line and form for R.C.C. bored piles of required diameter in all strata except hard rock including removing slush, all kinds of soil and rock, percolating water etc. complete from the above to keep ready for concrete after placing reinforcement but excluding the cost of providing and laying concrete and reinforcement.

600mm dia bore : 1) upto 12m from ground

Above 12m but upto 15m depth add 5%

Above 15m and upto 18 m depth add 5%

Above 18m and upto 21 m depth add 5%

Above 21m and upto 24 m depth add 5%

Providing and laying reinforced cement concrete of grade M 35 ( mix design) with coarse sand and graded granitic or basaltic aggregate 20mm nominal size as per mix design requirements in bored piles of specified diameter at the required workability and compaction as per the direction of the Engineer-in-charge including all operation for placing the concrete, lifting the casing in stages etc. but excluding the cost of reinforcement.

600mm dia bore : 1) upto 12m from ground

Above 12m but upto 15m depth add 10%

Above 15m and upto 18 m depth add 10%

Above 18m and upto 21 m depth add 10%

Above 21m and upto 24 m depth add 10%

Refilling the pipeline/foundation trenches plinth sides, foundation etc. with available excavated earth in layers not exceeding 20 cm depth consolidating each layer ramming and watering lead up to 50 M and all lifts and disposal of surplus earth as directed by Engineer in Charge.

Filling the pipeline/foundation trenches plinth sides, foundation etc. with bought out earth in layers not exceeding 20 cm depth consolidating each layer ramming and watering lead up to 10km and all lifts and disposal of surplus earth as directed by Engineer in Charge.

Rubble packing with hard laterite stone under floors including watering ramming and consolidating etc. in pipeline trenches and other foundations complete.

Supplying and filling in plinth under floors, trenches including watering ramming consolidating, dressing, complete. Sand

Providing & laying cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded granitic or basaltic stone aggrt. 40 mm. nominal size) excluding cost of centering, shuttering and finishing in: a. All works up to plinth level

Providing and laying in position ready mixed concrete (RMC) manufactured in fully automatic batching plant and transported to site of work in transit mixer for a lead up to 10kms having continuous agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work including pumping of R.M.C., from the transit mixer to the site of laying, excluding the cost of centering, shuttering, finishing and reinforcement including the cost of admixtures in recommended proportions as per IS : 9103 to accelerate/retard setting of concrete, improve workability without impairing strength and durability as per the directions of the engineer-in-charge. All works up to floor V level

iii M-20 grade of concrete

vi M-35 grade of concrete

Centering & shuttering including Strutting, Propping & removal of forms for :

Foundations, footings, bases for columns and mass concrete.

Vertical surfaces such as retaining walls, return walls, Partitions, walls (any thickness) including attached Pilasters, Buttresses, Plinth and string courses, Fillets and the like

Columns, Piers, Pillars, Abutments, Posts and struts (square rectangle polygon in plan)

Sides and Soffits of beams, Beam Haunchings, Cantilever, Girders, Bressumers and Lintels plinth beams not exceeding 1m in depth

Staircases (except spiral staircases) excluding landing

Suspended floors, roofs landings, shelves & their supports

Centering & shuttering including Strutting, Propping & removal of forms for sloping or battering surface (slabs, beams, louvers, etc) including folded plates ii. Where inclination to the horizontal exceeds 30° requiring shuttering on the underside & upper side if required (Only area of underside shall be measured for payment)

Providing corrosion resistant steel CRS-50 bars of (Confirming to IS 1786 if 1985) for RCC work including bending, binding & placing in position in all the floors along with factory made precast concrete cover blocks of specified sizes whose compressive strengths not less than that of surrounding concrete in the structural member .

Waterproofing of sunken slabs, toilet blocks, terraces on slabs under brickbats, roofs, water tanks. Cleaning the surface and filling cracks (if any), applying EPCO ACR wherever necessary, Providing and Moistening the surface with water to render it saturated. Mix Cement and Monobond WF in the ratio of 1.25 kg to 1 by weight and stir continuously. Apply minimum 2 coats with an interval of 12 hours minimum between the coats. Fix fibre mesh while the first coat is still tacky. Cure with sprinkling of water 3-4 times a day. incl. cost of scaffolding transport etc. as per direction of Engineer.

Second class dry brick flooring including filling joints with fine sand.

Providing and laying autoclaved aerated cement blocks masonry with 100 mm thick AAC blocks in super structure above plinth level up to floor V level in cement mortar 1:4 (1 cement : 4 coarse sand). The rate includes providing and placing in position 2 Nos 6 mm dia M.S. bars at every third course of masonry work.

Pre-cast cement concrete solid block masonry of compressive strength 70 kg / cm2 in cement mortar 1:4 (1 cement : 4 coarse sand ) in all sizes in superstructure from floor one level up to floor V level

6mm cement plaster to ceiling 1: 3 (1 cement : 3 fine sand) Extra for plaster to ceiling above 5m height from floor level for every additional height of one meter or part there of.

Providing & Fixing of Aluminium Lay in Plain Tile Ceiling on 24 /14 mm 'T' Framework of module 600mm X 600mm. Tiles of size 575mm X 575mm / 584mm x584mm made out of 0.6mm thick Aluminium. The tile shall be manufactured on advanced equipment, which includes several levelling. The tile end shall be raised up ward & bend outward to lay the tile in framework. The tile shall be Polyester based, Powder coated in white colour. Grid system for fixing ceiling tiles shall comprise of Tees. The 24 /14 mm main Tee runners shall be suspended at an interval of 1200mm centre to centre. The 24 /14 mm cross runner shall be suspended at 600 mm centre to centre and further supported with 24 /14 mm cross Tee at 600 mm centre to centre with internal locking arrangements to form grid of 600mm X 600mm. The main Tee shall be supported by means of 4mm GI rod from slab / roof. The suspension shall be provided at 1200mm to 1500 mm centre to centre. Tee framework would be made of GI and Powder coated.

Providing and applying white cement based putty of average thickness 1.00mm of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Providing and laying 1st class Mangalore tile roof covering with 25 x 50mm (1” x 2”) jamba wood or similar batten including nails etc. but excluding rafters.

Providing and laying ridge tiles laid dry & pointed with lime mortar 1: 2 (1 lime: 2 surkhi)

15mm cement plaster 1: 4 (1 cement : 4 fine sand) on the rough side of single or half brick wall.

18mm cement plaster in two coats under layer 12mm thick cement plaster 1:5 ( 1 cement : 5 coarse sand) and top layer 6mm thick with cement plaster 1: 3 (1 cement : 3 coarse sand) finished with sponge.

Ceiling & Wall painting (two or more coats) with plastic emulsion paint of approved brand and manufacture on new work to give an even shade.

Painting three or more coats with acrylic exterior paint of approved brand and manufacture including applying one coat of cement primer and one coat of surface treatment etc. complete.

Painting three or more coats with acrylic exterior texture paint of approved brand and manufacture including applying one coat of cement primer and one coat of surface treatment etc. complete.

Providing and applying white cement based putty of average thickness 1.00mm of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Providing and fixing 1st quality ceramic glazed wall tiles ( approved brand and manufacture )conforming to IS:15622 (thickness to be specified by the manufacture of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-charge in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand ) and jointing with grey cement slurry @3.3kg per sq.m including pointing in white cement mixed with pigment of matching shade complete. (c) Wall Ceramic Glazed Tiles : 300 x 600

Providing and fixing Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps and dados, jointing with grey cement slurry @3.3 kg per sqm, including pointing/grouting in white cement mixed with pigment of matching shade complete. a. 600 x 600 mm - Dark Shades

Providing & fixing bevelled edge mirror of superior glass (5mm thk) of approved Quality, shape & size complete with CP brass screws and washers, Cleats, CP studs etc Complete.

Providing and laying vitrified floor tiles in different sizes of (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622 of approved make in colours and shades as specified laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand) including grouting the joints with white cement and matching pigment etc., complete 600x 600 mm Dark Shades

Kotah stone slab flooring over 30 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid over & jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing & polishing complete 25 mm thick.

Providing and laying antiskid floor tiles 12 x 12 up to 16 x 16 in of (thickness to be specified by the manufacturer) of 1st quality conforming to IS:15622 of approved make in shades as specified laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand) including pointing the joints with white cement and matching pigment etc., complete a. Dark Shades

Providing and laying vitrified unglazed porcelain tactile floor tiles in different sizes (thickness to be specified by the manufacturer) and conforming to IS:15622 of approved make in colours and shades as specified laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand) including grouting the joints with white cement and matching pigment etc., complete 300 x 300 mm Design - Liner Supplying and Providing in position under deck 50mm thk non combustible Glass wool insulation 24 kg/m3 density with white pre laminated polypropylene facing (WMP-50) under the metallic roof complete for sound and heat insulation including cost of GI welded mesh of 75x75x1.60 thk stretched over purlin complete. The GI Welded mesh should be primed and painted with min. 2 coats of superior quality ready mixed paint for steel work

Providing and fixing 18 mm thick gang saw cut, mirror polished, pre moulded and pre polished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite of any colour and shade, area of slab over 0.50 sqm a. Jet Black Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/Granite/Cuddapah stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete.

Providing, fixing and placing in position Seasoned hardwood(1st Class Matti Wood) door frame of size 125mmx 65mm with holdfast, antitermite primer & flush door size 1500x 2400mm of 35mm thk. Shutter to be finished with Laminate of 1.5mm thk on both sides fixed on frame with Hinges & Hardwares of approved make, including providing and applying Enamel Paint of (1 Coat primer & 2 Coat enamel )on frame & wooden surface of shutter bidding etc. complete.

Providing, fixing and placing in position Seasoned hardwood(1st Class Matti Wood) door frame of size 125mmx 65mm with holdfast, antitermite primer & flush door size 1200x 2400mm of 35mm thk. Shutter to be finished with Laminate of 1.5mm thk on both sides fixed on frame with Hinges & Hardwares of approved make, including providing and applying Enamel Paint of (1Coat primer & 2 Coat enamel) on frame & wooden surface of shutter bidding etc. complete.

Providing, fixing and placing in position Seasoned hardwood(1st Class Matti Wood) door frame of size 125mmx 65mm with primer & flush door size 900x 2100mm of 35mm thk. Shutter to be finished with Laminate of 1.5mm thk on both sides fixed on frame with Hinges & Hardwares of approved make, including providing and applying Enamel Paint of (1Coat primer & 2 Coat enamel ) on frame & wooden surface of shutter bidding etc. complete.

Providing, fixing and placing in position Seasoned hardwood(1st Class Matti Wood) door frame of size 150mmx 65mm with primer & flush door size 750 x 2100mm of 35mm thk. Shutter to be finished with Laminate of 1.5mm thk on both sides fixed on frame with Hinges & Hardwares of approved make, including providing and applying Enamel Paint of (1Coat primer & 2 Coat enamel ) on frame & shutter finishes with Plastic coated (Phenol Formaldehyde Resin Coating) on both sides, etc

Window 1- Providing and fixing windows size 1250mm(W) x 2375mm(H) with 1st Class Matti Wood window frame of size 125mm x 50mm thk with horizontal intermediate wood frame 125mm x 50mm including 6mm thk toughened glass panel fixed with horizontal & vertical mullion of season wood finished with white coloured enamel paint finish to wooden surfaces etc. complete as per the detailed drawings.

Window 2- Providing and fixing of window size 600mmX 1350mm with1st Class Matti Wood frame size 100mm x 40mm including provision for Exhaust fan fitting. The units are partly fixed glazed, partly open for exhaust & openable shutter of 4mm thk clear reflective float glass embedded in Salwood shutter frame including hardware, & white coloured enamel paint finish to wooden surfaces etc. complete as per the detailed drawings.

Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes, channels, plates etc. with hairline finish, including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer, ( for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Large Wooden Table (1200x2400mm x 750mm) Supply of wooden table of size 1200Wx2400L of 15mm particle board finish with melamine impregnated paper with season wood legs.

Wooden chairs Supply of Chair of seasoned wood leg with seat size 38.1cm(W) X 39cm(L), including leatherite along with cushion, seat back size 38.1cm(W) X 39.0cm (H) with horizontal season wood backrest.

Book display cabinets Supply of Book display cabinate of Size 590cm(W) X 1744mm(H) X 400mm(D) fabricated with 15mm thk particle board finish with melamine impregnated paper . Tampered glass 6mm thk Shutter to fixed. Hinges & Handles to be chrome plated.

Sitting - Chairs Chair CBA Steel Godrej Interio - CH-7B 580X570X880 Supply of Chair seat size 580mm(W) X 570mm(H)X 880mm(H), including leatherite along with cushion, seat back size 45.7cm(W) X 42.4cm (H) with the Armrest tube of Ø 2.54cm x 0.2cm thk. M.S.E.R.W. tube and welded to the under structure assy. Armrest tube is made of tube of Ø 2.54cm x 0.2cm thk. and powder coated (DFT 40-60 microns), Godrej Interio -CH-7B

Steel Almirah/Cabinet - Large Godrej Interio - storewell 916x486x1980 Supply of steel cabinate of size 916mm X 486mm x 1980mm including Adjustable Shelves 4 levels of A4 size (85W X345H X 285D) file.Doors provided with Mazak handle three way locking mechanism. Cabinate to be finished with Epoxy powder coated paint of 50microns.

News paper stand Wooden newspaper racks 1000x450x1500 Supply of News Paper Stand of size 1000x450x1500mm with 15mm thk particle board panels of CRCA 0.6mm thk, finished with Epoxy powder coated thickness of 50microns.

Earthwork in excavation by mechanical means (hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sq.m on plan) including disposal of excavated earth lead up to 50 m and lift up to 1.5m disposed earth to be levelled and neatly dressed including providing barricading, danger lighting guarding as directed in : a: All kinds of soil

Plant Mix Method (Construction of granular sub-base by providing close graded Material, mixing in a mechanical mix plant at OMC, carriage of mixed Material to work site, spreading in uniform layers with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per clause 401 )

Providing and laying in position cement concrete1: 1.5: 3 (1 cement: 1.5 coarse sand: 3 graded granitic or basaltic stone aggrt. 20 mm. nominal size) excluding cost of centering, shuttering and finishing : All works up to plinth level

Providing and laying in position ready mixed concrete (RMC) manufactured in fully automatic batching plant and transported to site of work in transit mixer for a lead up to 10kms having continuous agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work including pumping of R.M.C., from the transit mixer to the site of laying, excluding the cost of centering, shuttering, finishing and reinforcement including the cost of admixtures in recommended proportions as per IS : 9103 to accelerate/retard setting of concrete, improve workability without impairing strength and durability as per the directions of the engineer-in-charge. All works up to floor V level

iii M-20 grade of concrete

Centering & shuttering including Strutting, Propping & removal of forms for : Foundations, footings, bases for columns and mass concrete.

Providing corrosion resistant steel CRS-50 bars of (Confirming to IS 1786 if 1985) for RCC work including bending, binding & placing in position in all the floors along with factory made precast concrete cover blocks of specified sizes whose compressive strengths not less than that of surrounding concrete in the structural member .

Laterite masonry in neatly dressed stones of size as specified in cement mortar 1: 4 (1 cement : 4 coarse sand) in foundation and basement.

Pointing over the laterite masonry

Providing & Applying 150 GSM GEO Textiles - for planters

15mm cement plaster 1: 4 (1 cement : 4 fine sand) on the rough side of single or half brick wall. Extra for providing and mixing water proofing material proportion recommended by the manufacturers.

Providing and laying flamed finish Steel grey granite stone flooring (size 400(L) x 200(W) x 40(D) mm) in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 40 mm thick stone slab over 35 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer : Flamed finish granite stone slab.

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment)

Providing and fixing stone tread tiles 40mm thick in single piece with rounded of nosing antiskid groove laid on and including 20mm (average ) thk bed of cement slurry including pointing with pigmented cement slurry to match the shade of the slab, cleaning etc. complete. Tread: Sera Grey Granite stone

Providing and fixing Granite stone slabs (flamed finish) 20mm thick in risers of steps, skirting, dado and pillars laid on cement paste and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete Riser: Sera Grey Granite stone

Providing and fixing stone coping of 50mm thick as per sizes shown in the drawing and including 35mm (average ) thk bed of cement slurry including pointing with pigmented cement slurry to match the shade of the slab, cleaning etc. complete.

Supply and installation of Cast Iron Tree grating of over all size 1200mm x 1200mm,with inner diameter of 600mm, the rate shall be including of all materials, labours, transportations, lead and lift and all work to be completed as per the directed by engineer.

Supply and installation of external Duo FRP Litter Bins B1 having size of 31inch x 17 inch x 32 inch, of Capacity 60L.each barel, top open in grade 202 FRP. Cost to include all fixings i.e. screws, bolts, washers etc. to complete. Design to be as approved by Client prior to fabrication or procurement.All works to be to completed to the satisfaction of the Engineer.

Drinking Water Fountain - Stainless steel standalone water stand

Signage - Place marker Supply and installing of Signage's (SG1) The Signages panel shall be with 10 mm thick SS plate (316 Grade) and Cortan steel of 10mm thick the size shall be as per the final drawing , letter will be vinyl sticker (LG Brand) in black.. Fixing with SS studs directly to the RCC wall.

SIgnage - Directional Signage Supply and installing of Signage's (SG2) The Signages panel shall be ,10 mm thick SS plate (316 Grade) and Cortan steel of 10mm thick the size shall be as per the final drawing letter will be vinyl sticker (LG Brand) in black.. Fixing with SS studs directly to the RCC wall.

Supply and installation of Stone bench with back rest as per the drawing and detail provided and as approved by engineer in charge

Supply and planting Trees of approved species of girth more than 300mm including replanting of trees ,necessary excavation in all kinds of soil and rock ,removing the roots carefully etc including all lead and lift etc complete as directed by engineer incharge.

Supply and planting Shrubs of height, spread and growth as per specifications, for understorey planting (low hedge @ 50cm to boundary of planter) in 20cm container size and >30cm height, plants must be healthy showing multiple branches with consistent signs of growth and free from disease. Apply a slow release fertiliser at time of planting.(20 plants per sqm),

Providing and fixing M.S. flat iron tree guard 60cm dia & 2 m high above ground level, formed of 4 nos. 25 x 6mm and 8 nos. 25 x 3mm vertical M.S. flat iron rings in two halves, bolted together with 8mm dia and 30 mm long bolts including painting two coats with paint of approved brand and manufacture over a coat of priming, complete in all respects.

Supply,Installation,Testing and commissioning of IP 20, T8 Batten - 4 feet, 36W-40W natural white Surface Mounted LED Light with all accessories required for installation. (Tubelights)

Supply, installation, testing & commissioning of surface mounted IP20 Circular type 6W-10W LED downlight Ms base white powder coated diffuser frosted glass base diameter 250 mm glass diameter 190 mm glass height 50mm fixture depth 95 mm height of glass 50 mm. (For Staircase)

Supply, installation, testing & commissioning of surface mounted IP20 Circular 12W-14W LED downlight Ms base white powder coated diffuser frosted glass base diameter 250 mm glass diameter 190 mm glass height 50mm fixture depth 95 mm height of glass 50 mm. (For Toilets)

Supply ,Installation ,Testing & commissioning of 10 W-14W –2 feet integrated IP20 LED batten T5 natural white wall mounted Tube Light with required all accessories (for mirror light).

Supply,Installation,Testing and commissioning of 14 W IP20 LED Light Fixture with all accessories required for installation (for common area passage location)

Supply,Installation,Testing and commissioning of IP 65, 1X8 W Bulk Head Light Fixture comprising of pressure die cast housing with acrylic diffuser and all accessories required for installation (for open terrace location)

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor single core cable in the independent recessed PVC conduit(heavy) of appropriate size as required. (b) 2 x 2.5 sq.mm + 1 x 2.5 sq.mm earth wire (20mm Conduit)

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor single core cable in the independent recessed PVC conduit(heavy) of appropriate size as required. c) 2 x 4 sq.mm + 1 x 4 sq.mm earth wire (20mm Conduit)

a. Supply, Installation, Testing & Commissioning of point wiring using 2 x 2.5 Sq.mm and 1x2.5 sq.mm earth wire (for 1st light point) / 2 x 1.5 Sq.mm and 1x1.5 sq.mm earth wire (for looping light points) multistrand copper FRLS wires 660/1100V grade PVC insulated wires in 20mm PVC conduit (heavy) of approved make including all conduit accessories such as bends, junction boxes, etc., complete. The wiring shall be done in complete looping in system. molded high quality type fixed in factory made integral units with clear earthing facility. The piano type/ Modular switches shall be fixed by using finally threaded brass screws. The switches shall be flush mounted as indicated in the drawing. The rate shall be include earthing of each light, fan and GI modular box, 5/6A switches, using PVC insulated. All the switches shall be located at a height of 1200mm from finished floor level. (unless otherwise stated).The wiring shall be complete with lugs ,thimbles, GI metal box, ceiling roses, junction boxes, switches, cover plate and all consumables rate should include (a) lighting circuit from DB to switch Board of light point.(b)Rough plastering packing conduits and removing debris with casing.

One light point / Fan point controlled by one switch.

Two light point controlled by one switch.

Three light point controlled by one switch.

Four light point controlled by one switch.

Five light point controlled by one switch.

Supply, Installation, Testing & Commissioning of point wiring using 2 x 2.5 Sq.mm and 1x2.5 sq.mm earth wire (for 1st light point) / 2 x 1.5 Sq.mm and 1x1.5 sq.mm earth wire (for looping light points) multistrand copper FRLS wires 660/1100V grade PVC insulated wires in 20mm PVC conduit (heavy) of approved make including all conduit accessories such as bends, junction boxes, etc., complete. The wiring shall be done in complete looping in system. molded high quality type fixed in factory made integral units with clear earthing facility. The light point shall be controlled by existing MCB in the existing DBs Not to include the cost of MCB.

Four light points controlled by MCB

Six light/Fan points controlled by MCB

Seven light points controlled by MCB

Eight light points controlled by MCB

Nine light points controlled by MCB

Ten light points controlled by MCB

Eleven light points controlled by MCB

Twelve light points controlled by MCB

Supply and Installation of Ceiling fan with all necessary accessories required for installation. 1200mm sweep

Supplying and fixing following size modular GI box along with modular base and cover plate for modulator switches in recess etc. as required (b) 4 Module ( 125 mm x 7 mm) Cat A ( Toilet Hand drier) Supplying and fixing following modular switch/socket on the existing modular plate and switch box including connections but excludingmodular plate etc. as required (c) 15/16 A switch Cat A (e) 6 pin 15/16 A socket outlet Cat A (Toilet Hand drier)

Supplying and fixing following size modular GI box along with modular base and cover plate for modulator switches in recess etc. as required (b) 4 Module ( 125 mm x 7 mm) Cat A Supplying and fixing following modular switch/socket on the existing modular plate and switch box including connections but excludingmodular plate etc. as required (c) 15/16 A switch Cat A (e) 6 pin 15/16 A socket outlet Cat A

Providing and fixing following capacity TPN disconnector fuse switch unit inside the existing cubicle panel board without HRC fuses including drilling holes in cubicle panel making connections etc as required '(c) 100 A TPN, CAT B ( for street light feeder pillar protection)

Supply of 4 core armoured PVC/XLPE insulated, PVCsheathed copper conductor cable of 1.1 KV grade with ISI mark conforming to IS:1554(Part I) ,IS:7098(Part I) with latest amendments of following size. 4 Core 10 sq.mm (MDB Panel to PDB & LDB - 1)

Supply of 4 core armoured PVC/XLPE insulated, PVC sheathed copper conductor cable of 1.1 KV grade with ISI mark conforming to IS:1554(Part I) ,IS:7098(Part I) with latest amendments of following size.4 Core 10 sq.mm (MDB Panel to PDB & LDB - 2)

Supply of 4 core armoured PVC/XLPE insulated, PVC sheathed copper conductor cable of 1.1 KV grade with ISI mark conforming to IS:1554(Part I) ,IS:7098(Part I) with latest amendments of following size. 4 Core 6 sq.mm (MDB panel to ELDB Panel )

Supply of 3 core armoured PVC/XLPE insulated, PVC sheathed copper conductor cable of 1.1 KV grade with ISI mark conforming to IS:1554(Part I) ,IS:7098(Part I) with latest amendments of following size.. 3 Core 6 sq.mm (Submersible Pump)

Supply of 3 core armoured PVC/XLPE insulated, PVC sheathed copper conductor cable of 1.1 KV grade with ISI mark conforming to IS:1554(Part I) ,IS:7098(Part I) with latest amendments of following size.. 3 Core 4 sq.mm (Domestic Tank - Terrace floor)

Supply of 3 1/2 core armoured PVC/XLPE insulated, PVC sheathed aluminium conductor cable of 1.1 KV grade with ISI mark conforming to IS:1554(Part I) ,IS:7098(Part I) with latest amendments of following size. 3.5 Core 50 sq.mm (GED panel to Proposed MDB panel)

Supply of 3 core armoured PVC/XLPE insulated, PVC sheathed copper conductor cable of 1.1 KV grade with ISI mark conforming to IS:1554(Part I),IS:7098(PartI) with latest amendments of following size. - 3 Core 6 sq.mm (ELBD panel To EDB-01 & EDB-02)

Supply of 3 core armoured PVC/XLPE insulated, PVC sheathed copper conductor cable of 1.1 KV grade with ISI mark conforming to IS:1554(Part I),IS:7098(PartI) with latest amendments of following size. - 3 Core 4 sq.mm (External)

Supply of 3 core armoured PVC/XLPE insulated, PVC sheathed copper conductor cable of 1.1 KV grade with ISI mark conforming to IS:1554(Part I),IS:7098(PartI) with latest amendments of following size. - 3 Core 2.5 sq.mm (External)

Supply of 3 core unarmoured PVC/XLPE insulated, PVC sheathed copper conductor cable of 1.1 KV grade with ISI mark conforming to IS:1554(Part I) ,IS:7098(Part I) with latest amendments of following size. - 3 Core 2.5 sq.mm (External)

Supplying and making cable end terminations with brass compression gland and copper lugs for folowing sizes of 3 Core PVC insulated PVC sheathed/XLPE aluminium conductor cable of 1.1 KV grade, complete as required. '(3) 3 x 6 Sq. mm.

Supplying and making cable end terminations with brass compression gland and copper lugs for following sizes of 4 Core PVC insulated PVC sheathed/XLPE aluminium conductor cable of 1.1 KV grade, complete as required. 4 x 6 Sq. mm.

Supplying and making cable end terminations with brass compression gland and copper lugs for following sizes of 4 Core PVC insulated PVC sheathed/XLPE aluminium conductor cable of 1.1 KV grade, complete as required. 3 x 4 Sq. mm

Supplying and making cable end terminations with brass compression gland and copper lugs for following sizes of 4 Core PVC insulated PVC sheathed/XLPE aluminium conductor cable of 1.1 KV grade, complete as required. 4 x 16 Sq. mm

Supplying and making cable end terminations with brass compression gland and copper lugs for following sizes of 4 Core PVC insulated PVC sheathed/XLPE aluminium conductor cable of 1.1 KV grade, complete as required. 4 x 6 Sq. mm

Supplying and making cable end terminations with brass compression gland and aluminium lugs for following sizes of 3 1/2 Core PVC insulated PVC sheathed/XLPE aluminium conductor cable of 1.1 KV grade, complete as required. 3 1/2 x 50 Sq. mm.

Earthing with GI earth pipe 2 mts long 40 mm dia medium class with ISI mark,of approved brands, including accessories and providing masonry enclosure with CI/RCC cover having locking /lifting arrangement and watering pipeetc. with charcoal or coke and salt) as required as per the Earthing Drawing provided by the Engineer-Incharge.The scope of work includes the following:a) Excavation of pit of size 1.0x1.0x 2.0 mtrs(min) and disposal of excavated soil. b) Class B GI pipe, 40mm diameter as per specifications. c)Charcoal/salt as per specs ( paid separately). d) Refilling the pit of size 1.0x1.0x 2.0 mtrs(min) with soft black soil of minimum resistivity i/c transportation. e)Masonary chamber with proper foundation, cover plate and locking arrangement.f) Testing of earth value with earth megger and certifications of its value. Aluminium tag with embossed earthing value to be attached to the pipe. g)watering arrangement(plumbing will be paid separately). ( 4 Nos Lighting arrester, 2 nos for Panel Body) (a) In soily strata

Supplying and laying 25 mm x 6 mm GI strip at 0.5 m below ground as strip earth electrode including soldering etc. as required

Supplying and fixing following way TPN sheet steel, single door, Verticle type MCB distribution board 415 V on surface/ recess complete with tinned copper busbar neutral busbar earth bar dinnbar detachable gland plate interconnections phosphotized and powder painted including earthing etc. as required ( but without MCB/RCCB/Isolator)interconnection between incomer MCCB and busbars of following ways (but without MCBs as required) '(a) 6 way (8+18), single door, Vertical type, Cat A (Ground floor - LDB-01)

Supplying and fixing B series SP MCB, 240 V, suitable for lighting and other loads of following poles in the existing MCB DB complete with connections testing and commissioning etc as required" (a) 5 A to 32 A, Cat A

Supplying and fixing 40 A, C series MCB suitable for lighting and other loads of following poles in the existing MCB DB complete with connections testing and commissioning etc as required. (e) TPN, Cat A

Supplying and fixing following rating double pole (single pole and neutral) 240 V RCCB having a sensitivity current upto 300mA in the existing MCB DB complete with connections testing and commissioning etc as required (a) 25 A, Cat A

Supplying and fixing following way TPN sheet steel, single door, Horizontal type MCB distribution board 415 V on surface/ recess complete with tinned copper busbar neutral busbar earth bar dinnbar detachable gland plate interconnections phosphotized and powder painted including earthing etc. as required ( but without MCB/RCCB/Isolator) '(a) 4 way ( 4 + 12) single door horizontal type Cat A (Ground floor - PDB-01) (First Floor - PDB-02 & LDB-02)

Supplying and fixing B series SP MCB, 240 V, suitable for lighting and other loads of following poles in the existing MCB DB complete with connections testing and commissioning etc as required" (a) 5 A to 32 A, Cat A

Supplying and fixing 40 A, C series MCB suitable for lighting and other loads of following poles in the existing MCB DB complete with connections testing and commissioning etc as required. (e) TPN, Cat A

Supplying and fixing following rating double pole (single pole and neutral) 240 V RCCB having a sensitivity current upto 300mA in the existing MCB DB complete with connections testing and commissioning etc as required (a) 25 A, Cat A

Supplying and fixing following way SPN sheet steel MCB distribution board 240 V on surface/ recess complete with tinned copper busbar neutral busbar earth bar dinnbar detachable gland plate interconnections phosphotized and powder painted including earthing etc. as required ( but without MCB/RCCB/Isolator) '(c) 12 way single door Cat A (Ground floor - EDB-01) (First Floor - EDB-02)

Supplying and fixing B series SP MCB, 240 V, suitable for lighting and other loads of following poles in the existing MCB DB complete with connections testing and commissioning etc as required" (a) 5 A to 32 A, Cat A

Supplying and fixing 6 A to 32 A, C series MCB suitable for lighting and other loads of following poles in the existing MCB DB complete with connections testing and commissioning etc as required. (c) DP, Cat A

Supplying and fixing following rating double pole (single pole and neutral) 240 V RCCB having a sensitivity current upto 300mA in the existing MCB DB complete with connections testing and commissioning etc as required (a) 25 A, Cat A

Supplying and laying 8 SWG copper wire at 0.5 m below ground level for conductor earth electrode including soldering etc. as required ( Earth connections for pumps, DB and external lighting works)

Supplying and making cable end terminations with brass compression gland and copper lugs for following sizes of 3 Core PVC insulated PVC sheathed/XLPE aluminium conductor cable of 1.1 KV grade, complete as required. 3 x 4 Sq. mm

Supplying and making cable end terminations with brass compression gland and copper lugs for following sizes of 3 Core PVC insulated PVCsheathed/XLPE aluminium conductor cable of 1.1 KV grade, complete as required.3 x 2.5 Sq. mm

Supply, installation, testing and commissioning of the following Panel fabricated out of 1.6 mm thick CRCA sheet steel in cubicle compartmentalized, dust and vermin proof, double door construction, powder coated with approved shade and partitions to segregate phases. Approved lockable covers with padlocking arrangement for each phase, recessed in wall or surface mounted as directed final distribution boards of the following description:

Main MDB Panel Supply, installation, testing and commissioning of the following Panel fabricated out of 1.6 mm thick CRCA sheet steel in cubicle compartmentalized, dust and vermin proof, double door construction, powder coated with approved shade and partitions to segregate phases. Approved lockable covers with padlocking arrangement for each phase, recessed in wall or surface mounted as directed final distribution boards of the following description: Main MDB Panel Incoming – I 100 Amps 4 Pole Isolator (MCCB) with following accessories: 3 nos. 100/5 amps 10 VA, CL 1 CTs with VAF meter) - 1 set & Energy Meter -1no Phase indicating light through shall be protected by 2 amps TP MCB and secondary by 2 amps TP MCB Bus Bars 150 amps TPN aluminium bus bars with coloured heat shrinkable insulated sleeve. 1 Set Outgoing 40 Amps TPN MCCB 5 Nos. 32 amps TPN MCCB 3 No. 20 amps TPN MCCB 2 No. 63 amps TPN MCCB 1No. All MCCB’s shall be of 16 KA breaking capacity. MDB Panel described as above.

Emergency Panel ( Inverter ) Incoming – I 32 Amps 4 Pole Isolator (MCB) with following accessories: 3 nos. 30/5 amps 10 VA, CL 1 CTs with VAF meter) - 1 set Phase indicating light through shall be protected by 2 amps TP MCB and secondary by 2 amps TP MCB Bus Bars 60 amps TPN copper bus bars with coloured heat shrinkable insulated sleeve. 1 Set Outgoing 25 Amps DP MCB ( 10 KA ) 3 Nos. Emergency Panel ( Inverter ) described as above.

Emergency Panel ( Inverter ) Incoming – I 32 Amps 4 Pole Isolator (MCB) with following accessories: 3 nos. 30/5 amps 10 VA, CL 1 CTs with VAF meter) - 1 set Phase indicating light through shall be protected by 2 amps TP MCB and secondary by 2 amps TP MCB Bus Bars 60 amps TPN copper bus bars with coloured heat shrinkable insulated sleeve. 1 Set Outgoing 25 Amps DP MCB ( 10 KA ) 3 Nos.

Supply, Installation, testing & commissioning of 2KVA inverter along with sealed maintenance free batteries to have minimum 90 minutes backup at full load in a powder coated sheet steel cabinet for housing inverter & batteries and complete in all respects as required

Supplying and fixing metal box of 180 mm x 100 mm x 60 mm deep (nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in front including providing and fixing 6 pin 5/6 A and 15/16 A socket outlet and 15/16 A switch connection painting etc. as required.( Weather proof)

Supplying and Installing following size welded ladder type , 50mm depth , M.S.cable tray of GI pregalvanised/hot dip galvanised/ powder coated finish, in convenient sections, joined with connectors, suspended from the ceiling with suitable MS suspenders including bolts and nuts,painting suspenders etc, complete as required. 200 mm width X 50 mm depth with runner size 15x50x15mm, rung size 20x40x20mm with rungs at 250mm c/c.(14SWG)

Laying of one number PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of size not exceeding 25 sq.mm in the existing RCC/HUME/STONEWARE Metal pipe, etc. complete as required

Laying of one number PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of size exceeding 25 sq.mm but not exceeding 400 sq.mm in the existing RCC/HUME/STONEWARE Metal pipe, etc. complete as required

Laying of one number PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of size not exceeding 25 sq.mm on surface, etc. complete as required (Pole junction box to LED fixtures)

Supply, Installation, Testing & commissioning of 25W LED Pole Light-IP65 Type 90mm dia Hot dip galvanized circular G.I. pole 3.5 Mtr. height in single section with base with Suitable Stiffener, reducer at top suitable for mounting with 25W LED light fixture with base plate of 250mm x 250mm x 10mm thick,& pole thickness 3.0 mm ,with stiffener, 4 no’s 25 mm dia hole of foundation nut & bolts (20 mm dia bolt & 300 mm long). The pole shall be Provided with inspection window ,500 mm from bottom above fixed Base plate, cutted with proper CNC machine with Lockable Cover for fixing of inbuilt control gear box. Inbuilt Bakelite sheet with 4way connectors for incoming and outgoing cable i.e. loop in loop out arrangement including provision of fixing double compression gland & 10A MCB for Lighting Fixture etc.

supply and fixing of 6 Watts Outdoor Up Down Wall Mounted LED Light, IP65 protection ,Warm White with dimensions (8cm width x6.5 cm dia x 14.5 cm length) as per direction of the Engineer.

Supply,Installation,Testing and commissioning of IP 67 & Ik 08 ground burial light with die cast aluminium housing with high corrosion resistance. Stainless steel front ring 304 grade . Stainless steel fasteners in 316 grade. Cable entry PG9 cable gland, durable silicon rubber & clear toughened glass . Walk over min 200 kg pressure load. With high corrosion resistance colour with chemical chromicised. Dia 120 mm with HI LUMEN LED 6W , beam15 degree , 3000K, Luminaries shall be complete in all manner to installed at site with all fixing arrangement etc as required & as per site condition. Fitting shall be suitable for loop in loop out arrangement with flexible cable including IP 66 gland and including all accessories

Supplying and fixing of following sizes of rigid PVC conduit along with accessories in surface(medium)/recess(heavy) including cutting the wall and making good the same in case of recessed conduit as required. (b) 25 mm

Supplying and fixing of following sizes of rigid PVC conduit along with accessories in surface(medium)/recess(heavy) including cutting the wall and making good the same in case of recessed conduit as required. (c) 32 mm

Supplying & erecting FRP box of size 150mm x 125mm x 100 mm, 2.7 mm thick complete on pole/wall as per specification No. CB-SB

Supply & fixing of weather proof thermoplastic Junction box (IP65 ) for External Lighting area, complete as required with grommets, & connectors.

Providing and fixing white vitereous china pedestal type (Europen type) water closet with seat as lid, whth C.I. brass hinges and rubber fitings 15 lts white vitreous china low level flushing cistern with fittings as brackets 40 mm white precelain 3enameled flush bad, 25 mm overflow pipe with specials and mosquito proof coupling of approved municipal design complete, including cutting and making good the walls and floors where required. (a) W.C. pan with white plastic seat and lid

Providing and fixing Hand Shower (Health Faucet) with 8mm dia, ABS/brass body with double lock 1.00m long Flexible tube (Brass plated stainles steel flexible hose) and wall hook of approved quality confirming to IS standards.

Providing and fixing C.P. BIB cock with wall flange jaquar orequivalent make continental (CAT.NO. CON­047) including necessary sockets/ union nut etc. complete.

providing and fixing oval type under counter wash hand basin of 16inch x 22 Inches size and of special colour shade having telephonic black / coloured granite of 180 mm thick stone black kadappa framework including chromium plated coupling bottle trap using CERA company or equivalent ovel type wash basin model no 3448 as per detailed drawing or as directedby engg incharge etc to complete

Providing and fixing C.P.pillar cock long neck with aerator jaquar make continental (Cat.No. CON- 021)

Providing and fixing White Glazed Earthenware full stall type Urinal with P.V.C. flushing cistern of 5 liters capacity with fitting, inlet pipes and stop tap, brackets for fixing the cistern, 32 mm dia. P.V.C flush pipe with fittings and flushing arrangement including lead soil pipe, lead trap, soil pipe connectionup to the outside face of the wall

Supply and fixing of Flushing tank automatic Urinal 5ltr. (P.V.C.)

Providing and fixing toilet paper holder : (a) C.P. brass

Providing & fixing liquid soap container with C. P. brass lid and brackets fixed to wooden cleats with C. P. brass screws (a) Glass container

Supply & Fixing of Tissue Paper Dispenser with all required accessories required for installation.

Supply and fixing of C.P.Angular stop cock jaquar make continental (Cat.No. CON-053)

Providing and fixing NICKEL chrome plated copper alloy Fancy BOTTLE TRAP ECONOMY TYPE 32MM Jaquar make or equivalent. Confirming to IS 8931;1993

Providing and fixing on walls/ ceiling/ floor 15 mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete.

Providing and fixing on walls/ceiling/floor 20 mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete.

Providing and fixing on walls/ ceiling/ floor 25 mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete.

Supplying at store or site of work including railway freight, carting, loading, unloading, stacking etc. galvanized mild steel continuous weld tubes conforming to IS:1239 (part-I) 1975, with latest amendments, screwed at both the ends as per IS : 554 - pipe threads, one end fitted with socket, other end with plastic protection ring at random lengths 4-7 meters.

32 mm dia.

40 mm dia.

50 mm dia.

65 mm dia.

Supplying, laying, jointing, testing & commissioning approved make class 'B' G.I. pipesand fittings confirming to IS 1239 PI & II, malleable fittings viz., tees, elbows, flanges, unions etc.,including cutting threading, fixing in/on walls,below ceilings, under floor etc., as per drawings. The quoted rate shall include necessary, chasing in walls, making bores in walls,foundations and slabs and making good the chased surfaces and bores in CM 1:4 MS pipe supports with GI clamps, Anchor fasteners, grip bolts, nuts and bolts etc,painting bitumen paint to cold water supply lines etc.,complete.

G.I. Pipe 20mm dia. Medium type

G.I. Pipe 25mm dia. Medium type

G.I. Pipe 32mm dia. Medium type

G.I. Pipe 50mm dia. Medium type

G.I. Pipe 65mm dia. Medium type

Supply and fixing of Ball cock for 25mm dia with all necessary accessories.

Supply and fixing of Ball cock for 32mm dia with all necessary accessories.

Supply and fixing of Ball cock for 40mm dia with all necessary accessories.

Supply and fixing of Butterfly valve for 65mm dia with all necessary accessories.

Supply and fixing of 32 mm Dia Check Valve with all necessary accessories.

Supply and fixing of 150 mm Dia Check Valve with all necessary accessories.

Supply and fixing of 20 mm Air vent with all necessary accessories.

Supply and Fixing of UPVC Inlet Hooper

Supply and fixing of puddle flanges with required accessories. 65 mm Dia.

Supply and fixing of puddle flanges with required accessories. 50 mm Dia.

Supply and fixing of puddle flanges with required accessories. 40 mm Dia.

Supply and fixing of puddle flanges with required accessories. 25 mm Dia.

Supply and fixing of puddle flanges with required accessories. 15 mm Dia.

Supplying, installing, testing and commissioning level controller with necessary cable and accessories.

Supply of Domestic Water Meter, horizontal inferential, Multi Jet type with magnetic drive and dry dial suitable for ambient 50 degree C temperature duly sealed against tampering complete with couplings at both ends and conforming to Class B as per IS 779/1994,(Reaffirmed:2004)with amendments 1 to 5 with ISI mark along with manufacturer's test certificate and guarantee certificate, including cost of all materials and labours with ISI mark with Plastic Cover & Brass Body- 25 Dia

Supplying and fixing of ASTM UPVC pipe conforming to ASTM 2467 with ISO 14001 etc. complete with all accessories and fittings. SCH-80(Blue)/(white) - 40 mm Dia

Supplying and fixing of ASTM UPVC pipe conforming to ASTM 2467 with ISO 14001 etc. complete with all accessories and fittings. SCH-80(Blue)/(white) - 50 mm Dia

Supplying and fixing of ASTM UPVC pipe conforming to ASTM 2467 with ISO 14001 etc. complete with all accessories and fittings. SCH-80(Blue)/(white) - 75 mm Dia

Supplying and fixing of ASTM UPVC pipe conforming to ASTM 2467 with ISO 14001 etc. complete with all accessories and fittings. SCH-80(Blue)/(white) - 110 mm Dia

Supplying, laying, jointing, testing and commissioning of approved make UPVC pipes class III 6 Kg/cm2with solvent cement joints confirming to IS 4985 for kitchen sink, wash basin outlets Outlets & Antisyphonage Pipes. The quoted rate shall include necessary chasing in walls making good the same in C.M. 1:4, necessary fittings viz.,elbows,tees etc., with G.I clamps. Anchor fasteners, Grip bolts, nuts and bolts, etc,complete. 160 mm UPVC Pipe

Supplying and fixing approved make UPVC floor trap with 75mm dia outlet with extension piece and CP brass cover on top etc., complete.

Supplying and fixing of approved make Floor Drain with CP grating (Medium duty) on top and 50 mm dia PVC bend etc., complete.

Supplying, jointing, testing & Commissioning of approved make terrace rain water Kurra medium duty Type-A 110mm dia Upvc grating on top etc., to complete.

Supplying, laying, jointing, testing and commissioning of approved make UPVC pipes class III 6 Kg/cm2with solvent cement joints confirming to IS 4985 for kitchen sink, wash basin outlets Outlets & Antisyphonage Pipes. The quoted rate shall include necessary chasing in walls making good the same in C.M. 1:4, necessary fittings viz.,elbows,tees etc., with G.I clamps. Anchorfasteners, Grip bolts, nuts and bolts, etc,complete. 160 mm UPVC Pipe

Providing at store or site work non-pressure RCC pipes of with collar joints conforming to IS:458-2003 revised as per amendment No.11 , including freight, carting, loading, unloading, stacking etc. complete. 250 mm

Providing and fixing 15cm x 10cm salt glazed stoneware gully trap in cement concrete 1:4:8 outside the building including cast iron grating in the sink, connecting glazed stoneware pipe, brick masonry chamber with cast iron lid and cast iron grating for the gully trap along with frame and cover.

Supplying, laying, jointing, testing & commissioning approved make class 'B' G.I. pipesand fittings confirming to IS 1239 PI & II, malleable fittings viz., tees, elbows, flanges, unions etc.,including cutting threading, fixing in/on walls,below ceilings, under floor etc., as per drawings. The quoted rate shall include necessary, chasing in walls, making bores in walls,foundations and slabs and making good the chased surfaces and bores in CM 1:4 MS pipe supports with GI clamps, Anchor fasteners, grip bolts, nuts and bolts etc,painting bitumen paint to cold water supply lines etc.,complete.(For Municipal Water Supply) GI 50 mm dia (Medium)

Supplying, of HDPE pipes at store or site of work including loadingunloading, stacking, transit insurance etc. complete bearing ISI mark & conforming to IS: 4984-1995 & made from PE 100 resin .Class IV (6 kg/cm2) J.200 mm dia

Supplying of C. I.. Foot rests for manhole conforming to IS:5455-1969 weighing 5.4 kgs

Construction of manhole rectangular in shape including cement concrete 1:3:6 (1 cement:3 coarse sand:6 graded stone aggregate 20mm nominal size) foundation thickness of concrete 20cms and offset 10cms on both sides and first class brick work with bricks class designation 100kg/sq.cm (wire cut bricks) cement mortar 1:3 (1 cement : 3 coarse sand) 23cms thick including providing & fixing CI footrests confirming to IS 5445/69 or revised and whose weight shall not be less than 5.30kgs including fixing in man-hole at 30cm c / c in 20x 20x10cm cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size) and 12mm thick plaster inside and outside with cement mortar 1:3 (1 cement : 3 coarse sand) including adding waterproofing compound of approved brand in cement mortar with a floating coat of neat cement and making channel in cement concrete 1:2:4 (1 cement :2 coarse sand : 4 graded stone aggregate 20m nominal size) neatly finished complete as per standard design.

Inside size 0.90 x 0.60m and 1.00m deep ( with medium duty DI manhole cover & frame of size 0.90x 0.60m weighing 105 kgs including fixing with cement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size and applying the frame & cover with coal tar.)

Supply, installation, testing and commissioning of Fire booster pump (pressurisation pump) comprising of the following:Pump - KDI-844 / 5.5KW,a. Horizontal/Vertical centrifugal pump, suitable for operation on 415 volts ± 6%, 3 phase, 50 HZ A.C supply. The installation shall be complete with Flexible coupling and coupling guard, complete as required. The pump casing shall be CI, shaft shall be SS & impeller/ shaft sleeve/casing wearing ring shall be bronze. The pump shall be provided with mechanical seal The system shall be complete with necessary pressure gauge with gun metal shut off cock on delivery side. (The pump should meet the condition and shall be gotten approved by the Local fire Authority). b. Squirrel cage induction motor TEFC type for operation on 415 V, 3 phase 50 Hz AC supply for the above pump with a synchronous speed of 2900 RPM with flexible coupling and coupling guard etc. as required . c. Common base plate for (a) and (b) from M.S. channel as required size. . Flow ;- 450LPM, 35mtr head

Supplying, installing and commissioning C.I.flanged "Y" type Strainer with SS mesh,suitable flanges, nuts, bolts, gaskets etc. complete. 150 mm Dia

Supplying, installing, testing and commissioning of G.I. Pipes confirming to IS 1239 Pt - I Heavy grade with painting, suitable type of supports ( Shall be fabricated by M.S. Channel / Angle / Flat for above 50 mm dia), anchor fasteners, bolts nuts, clamps, "U" bolted, malleable specials such as Reducers,Tees, elbows, flanges. Including cutting, Welding, fixing in / on walls, ceiling by using suitable supports etc, as per drawings. The quoted rate shall also include for chasing / chipping walls, making bore holes in walls / floor and making them good with filler material and finished in cement morter etc. complete. 150 mm Dia

Supplying, installing, testing and commissioning of G.I. Pipes confirming to IS 1239 Pt - I Heavy grade with painting, suitable type of supports ( Shall be fabricated by M.S. Channel / Angle / Flat for above 50 mm dia), anchor fasteners, bolts nuts, clamps, "U" bolted, malleable specials such as Reducers,Tees, elbows, flanges. Including cutting, Welding, fixing in / on walls, ceiling by using suitable supports etc, as per drawings. The quoted rate shall also include for chasing / chipping walls, making bore holes in walls / floor and making them good with filler material and finished in cement morter etc. complete. 100 mm Dia

Supplying, Installing, testing and commissioning CI butterfly valves as per BS 5155 (PN 10) slim seal standared lever operated type with required flanges, nuts, bolts etc. complete. 150 mm

Supplying, Installing, testing and commissioning CI butterfly valves as per BS 5155 (PN 10) slim seal standard lever operated type with required flanges, nuts, bolts etc. complete. 100 mm

Supplying, installing, testing and commissioning of C.I. Non-return valves as per IS:5312( PN 10) swing check type with required flanges, nuts, bolts and gaskets etc. complete. 150 mm Dia

Single headed hydrant valve oblique type conforming to IS 5290, made of gunmetal with 63 mm dia instantaneous outlet and 80 mm dia flanged inelt ,Blank caps , chain and CI hand wheels etc complete.

15 M long, 63mm dia RRL hose conforming to IS 636 Type A with instantaneous couplings and Hoses shall be stored inside fire duct on wall with firmly fastened steel rod.

Gun metal short branch pipe with nozzle conforming to IS 903.

Hose Reel, Swinging 360 degrees wall mounting type, complete with 19mm bore, 36mtr long, high pressure braided rubber hose bearing IS:444 type II mark, 6mm bore PVC Shut-off valve nozzle and confirming to IS 884 without considered inlet valve.

Fire duct Shutter fabricated out of M.S. sheet and frame, door shall be 900mm x 1350 mm min. & fixed with 4 mm thick Glass, suitable Rubber beedibg and Locking arrangement. Quoted rate shall be includes all fasteners etc, and complete shutter shall be powder coated of approved colour both inside and out side.

Supply and fixing Co2 type(4.5Kg) fire extinguisher new seamless cylinder with powder coated finish, made out of Manganese steel with initial fills, hose, wall brackets, nuts, bolts etc as complete with ISI mark confirming to IS: 156838 as approved and instructed by the engineer in charge

Supply and fixing of dry chemical powder type (DCP) fire extinguishers (ABC Type) of 6 Kg capacity, Pressurized with nitrogen, mfgd to IS:13849 with ISI mark fitted with pressure gauge, GM cap nozzle complete with initial charges and installation brackets and screws with ISI 15683 marks etc. complete as approved and instructed by the engineer in charge.

Supplying, Installing, testing and commissioning of Lawn Hydrant 25 mm dia lawn hydrants consisting of 25 mm dia Ball valve, GI nipple and quick release coupling / threaded hose receiver complete as required.with accessories

Supply and installation of 2 way SS fire brigade inlet

BANSAL INFRAPROJECTS PRIVATE LIMITED