SPECIAL REPAIRS TO CERTAIN BUILDINGS AND PROVN OF TWO STORE ROOMS AT SUKNA MIL STN UNDER GE SUKNA

Amount

Taking down chowkats or frames with Wooden/PVC/Flush shutters (without taking off shutter from frames) not exc. 1.5 sqm each, including cutting holes for removing the hold fast etc, also including taking down of grills/ guard bars (where exists) and disposing off the retrieved debris outsite the premises, complete all as specified and as directed.

Taking down chowkats or frames with Wooden/PVC/Flush shutters (without taking off shutter from frames) exc. 1.5 Sqm but n exc 4 Sqm each, including cutting holes for removing the hold fast etc, also including taking down of grills/ guard bars (where exists) and disposing off the debris outsite the premises, complete all as specified and as directed.

Taking down wooden/PVC/Flush shutters of any description n exc 1.00 Sqm each, complete all as specified and directed.

Taking down wooden/PVC/Flush shutters of any description exc 1.00 Sqm & n exc 2.00 Sqm each, complete all as specified and directed.

S&F factory made 1.25 mm thick pressed steel frame of size 105 X 60 mm for doors with one or more rebates includings necessary provision of lugs, locks strike plate etc, also including application of one shop coat of Zinc Chromate primer, complete all as specified and as directed. Note :- Hinges shall be paid for separately.

S&F factory made 1.25 mm thick pressed steel frame of size 125 X 60 mm for doors with one or more rebates includings necessary provision of lugs, locks strike plate etc, also including application of one shop coat of Zinc Chromate primer, complete all as specified and as directed. Note :- Hinges shall be paid for separately.

M&L for cement concrete 1:3:6 type C-1 (using 20mm graded stone aggregates) as in hold-fast blocks, blocks for fixing lugs, filling of pressed steel chowkhat and the like including necessary form work, complete all as specified and as directed.

Demolition of cement concrete (unreinforced) in ground floors and pavings n.exc 15cm thickness (below or above ground level), Complete all as specified and directed.

Demolition of reinforced cement concrete (reinforcement cut as required to facilitate demolition) of any description & in any position not otherwise specifically provided for including disposing off the retrieved debris outside the premises, complete all as specified and as directed.

Dismantling wrought iron as in rafters, purlins, truss etc and/or mild steel work of any description not otherwise provided for, complete all as specified and as directed

Dismantling timber scantlings under 40 sq. cm and over in section, in any position like trusses, rafters, purlins etc, complete all as specified and as directed.

Dismantling timber scantlings 40 sq. cm and over in section, in any position like trusses, rafters, purlins etc, complete all as specified and as directed.

S&F roof trusses (framed), trussed, purlins, crane gantry, rails and fastenings and heavy brackets framing (Beam, Tee, Angle,, Channel or Flat Sections) including distance pieces, cleats, etc of Grade Fe 410-W (Gde-E-250) Quality - B, includng welding or riveting etc, complete all as specified and as directed.

S&F steel work in tubular trusses, purlins, rafters, Fan Hook & similar work including special shaped washers etc complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St.-240, also including necessary welding etc complete all as specified and as directed.

S&F plates of Grade Fe 410-W (Gde E-250) quality - B (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attacment including welding or riveting etc, complete all as specified and directed.

S&F Mild steel screw bolts (machine made) (diameter of neck 16 to 20 mm) with hexagonal or square heads at one end or screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, length of bolt exc 22.50 cm but n. exc 30 cm long, complete all as specified and as directed.

Taking down 15mm bore steel tubing & connections, complete all as specified and as directed.

All as per item No 17 above but 20 mm bore.

All as per item No 17 above but 25 mm bore.

S&F 15mm bore medium grade, galvanised steel tubing (including in short lengths) with and including all fittings, fixed partly on the surfaces and partly concealed in the walls & ceiling or laid in floors, also including cutting chases of the required size and making good the same after fixing of the pipes in CM 1:3 to match with the adjoining surfaces, complete all as specified and as directed.

All as per item No 20 above, but 20 mm bore, complete all as specified and as directed.

All as per item No20 above, but 25 mm bore, complete all as specified and as directed.

S&F Factory made Solid PVC Door Frame of size 50mm x47mm made out of 5mm plain colour PVC sheet, reinforced with M.S. Square tube, complete all as specified and shown on drawing for SI No. 08095 on Srl Page No. 180 of SSR (Part-II) and as directed.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tube for top and bottom rails.MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width struck inside with solvent cement for stiles and plain colour PVC sheets for top rail,lock rail and bottom rail, on either side & as gap insert for top rail & bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles and rails with suitable PVC sheet beading and jointed together with solvent cement, complete all as shown on drawing for SI No 8080 on Srl Page No 176 of SSR Part-II, complete all as specified and as directed.

All as per item No 24 above but wire gauzed i.e. panel will be of wire gauze in lieu of PVC sheet panel. The wire gauze shall be wrapped on an additional square 8mm M.S. Solid tube and this tube shall be welded to M.S. tubes. The wire gauge shall be stretched to tighten firmly, complete all as specified and as directed.

S&F framed work as in doors or gates of angle or other section with gusset plates, ails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and uides) and hanging; also fastening and fixing complete including dismantling of old one, complete all as specified and as directed.

S&F 2nd class hardwood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, complete all as specified and directed.

S&F Factory made 30mm thick, flush shutter, solid core construction, with particle board core and ply wood face panels, commercial type on both sides including provision of 6mm thick 2nd class hard wood edging to the exposed edges of the shutter, complete all as specified and as directed.

S&F Factory made 40mm thick, flush shutter, solid core construction, with particle board core and ply wood face panels, commercial type on both sides including provision of 6mm thick 2nd class hard wood edging to the exposed edges of the shutter, complete all as specified and as directed.

M&L for 2nd class hard wood (Hollock/Kalasiris/Brjsal/Gamari) (kiln seasoned and chemically pressure treated) 30 mm thick glazed and skeleton shutters, open rebated and prepared to rceieve glass, gauze, etc, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass,etc, sizes of members of shutters as specified in SSR Part-1, Section 8, clause 8.24 (a), complete all as specified and as directed.

M&L for 2nd class hard wood (Hollock/Kalasiris/Brjsal/Gamari) (kiln seasoned and chemically pressure treated) 35 mm thick glazed and skeleton shutters, open rebated and prepared to rceieve glass, gauze, etc, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass,etc, sizes of members of shutters as specified in SSR Part-1, Section 8, clause 8.24 (a), complete all as specified and as directed.

M&L for the Framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forget into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 290 Gde E-165, complete all as specified and as directed.

S&F stainless steel wire cloth 0.63 mm nominal dia of wire and average width of aperature 1.40 mm and fixed with and including stainless steel wire staples etc, complete all as specified and as directed.

Hacking out old broken glass any thickness, size, quality and description from metal frames including punching or drilling out old glazing pins /springs clips, complete all as specified and directed.

S&F 3mm thick sheet glass of ordinary quality and glazing for steel surrounds with & including oil putty, in squares n exc 0.50 sqm in each pane, complete all as specified and as directed.

All as per item No 35 above but sheet glass frosted on one side.

S&F mild steel flat iron etc as in hold fast and similar articles conforming to Fe-290 Gde -E-165, complete all as specified and directed.

S & F factory made steel windows with side hung shutters including box type hinges with steel handle, and peg stay, complete with glazing bars, dovetaild or welded, also including application of one shop coat of Zinc Chromate primer, complete all as specified and directed.

All as per Item No 38 above, above but steel windows without glazing bars.

S&F Factory made, steel ventilator with top hung shutter including hinges, steel peg stay, including application of one shop coat of Zinc Chromate primer, complete all as specified and directed.

M&L for green colour badminton court synthetic flooring of thickness 8mm complete fixing by using adhesive component and dimentional marking with paint/highlighter paint as per given dimension, complete all as specified and directed.

M&L for preparing of new steel & iron surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer, complete all as specified and directed.

M&L for preparing of new steel & iron surfaces of any description, not otherwise described, n.exc 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer, complete all as specified and directed.

M&L for Preparation of steel and iron surfaces of any description duly applied with shop coat of primer, over 10 cm in width or girth , not otherwise described and painting with two coats of synthetic enamel paint, complete all as specified and as directed. Note : Cost of application of shop coat of primer not included in this item.

M&L for preparing new wooden surfaces of any description not otherwise described, over 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified and directed .

S&F mild steel 300mm, ordinary rat tail rod pattern springs including roller and roller plate, complete all as specified and as directed.

S&F 300mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy, complete all as specified and as directed.

S&F 250mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy, complete all as specified and as directed.

S&F 250mm long, mild steel, sliding door bolt, stove enamelled black, bolt type, with bright bolt not less than 12mm dia, with & including a minimum of 6 bolts & nuts, complete all as specified and as directed.

S&F 100mm size butt hinges, medium weight, cold rolled, mild steel, complete all as specified and as directed

S&F 75mm size butt hinges, medium weight, cold rolled, mild steel, complete all as specified and as directed

S&F 150 mm size aluminium handle, cast type, anodised, complete all as specified and as directed.

S&F 100 mm size aluminium handle, cast type, anodised, complete all as specified and as directed.

S&F 125 mm size aluminium handle, cast type, anodised, complete all as specified and as directed.

S&F Aluminium anodised barrel tower bolt, 200 mm long of extruded section, complete all as specified and as directed.

S&F Aluminium anodised barrel tower bolt, 150 mm long of extruded section, complete all as specified and as directed.

S&F Aluminium anodised barrel tower bolt, 125 mm long of extruded section, complete all as specified and as directed.

S&F floor door stopper holder 140mm long of Aluminium alloy body and tongue, anodised, with hard drawn steel spring,fixed in floor, complete all as specified and directed.

S&F Door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed, complete all as specified and directed.

S&F Mortice lock, four lever vertical type, size100 mm, complete all as specified and directed.

M&L 18/19 mm thick particle board, medium density, flat pressed, single layer type with BWR type adhesive, fixed with screws to timber frame work as in cupboard shelves, partition, etc, including provision of 2nd Class Hardwood, 4 mm thick beading on the edges of the particle board, complete all as specified and directed.

M&L in repair plywood, grade BWR, type BB, fixed with screws to timber frame work as in shelves, complete all as specified and directed.

S&F 100 mm size, hasp and staple , safety type, aluminium anodised with mild steel hinge pin including bolt to hinge plate and fixed with screws, complete all as specified and directed.

S&F Continuous (piano) hinges [40mm width of flaps(when open)], mild steel, bright finish or electrogalvanised, complete all as specified and directed.

S&F 40 mm dia mild steel bright finish cup board knobs with and including nuts, screws and washers, complete all as specified and directed.

S&F stainless steel decorative curtain rod of 25 mm bore with wood finishes, complete all as specified and as directed.

S&F brackets and funnel caps suitable for the curtain rod to be provided under item No 45 above, complete all as specified and as directed.

M&L for brushing neat cement slurry with 1.00 kilogram of cement per square metre over sunken floor surfaces etc, providing 10 mm thick plastering in cement mortar 1:3 mixed with liquid water proofing compound, finished even and smooth, complete all as specified and as directed. Note :- Supply only water proofing compound shall be measured and paid separately under the respective Item.

M&L for applying evenly bituminous tack coat @ 1.20Kg/Sqm of industrial bitumen blinded with 0.006 cum of coarse sand per Sqm on the surfaces of the sunken floor , complete all as specified and as directed.

M & L for plain cement concrete type E-2 (1:5:10) (using 40 mm graded crushed stone aggregates) as in sunken floor etc, complete all as specified and directed.

M&L for plain cement concrete (1:2:4) type B-0 (using 12.50 mm graded stone aggregate), 25 mm thick as in sunken portion, complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), including disposing off the retrieved debris outside the premises, complete all as specified and as directed.

M & L for coloured Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) of approved size, area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white cement mixed with pigments to match with the shade of tiles, over and including 15mm thick screed bed in CM 1:6, complete all as specified and as directed.

M & L for coloured Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) of approved size, area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white cement mixed with pigments to match with the shade of tiles, over and including 15mm thick screed bed in CM 1:6, complete all as specified and as directed.

All as per item No 74 above but in skirting/dado on vertical surface and including 10mm thick screed bed in CM 1:3, complete all as specified and as directed.

M & L for coloured Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) of approved size, area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white cement mixed with pigments to match with the shade of tiles, over and including 15mm thick screed bed in CM 1:6 and roughening of old concrete floor by picking,sweeping clean and washing down with water, complete all as specified and as directed.

M & L for coloured Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) of approved size, area of each tile exceeding 0.18 sqm but not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white cement mixed with pigments to match with the shade of tiles, over and including 15mm thick screed bed in CM 1:6, complete all as specified and as directed.

All as per item No 77 above but in skirting/dado on vertical surface and including 10mm thick screed bed in CM 1:3, complete all as specified and as directed.

M & L for coloured vitrified Ceramic tiles (Dark shade) 10 mm thick (square/ rectangular) of approved size, area of each not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white cement mixed with pigments to match with the shade of tiles, over and including 20mm thick screed bed in CM 1:6, complete all as specified and as directed.

All as per item No 79 above but in skirting/dado on vertical surface and including 10mm thick screed bed in CM 1:3, complete all as specified and as directed.

M&L for coloured Glazed ceramic tiles of size 300mmx 450mm , 6 to 7 mm thick on the vertical surfaces such as in skirting / dado etc, set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match with the shade of the tiles, over and including 10mm thick cement mortal backing coat in CM 1:4, complete all as specified and and as directed.

M&L for 75mm thick cement concrete (1:3:6) type C-2 (using 40mm graded stone aggregates) as in sub base of flooring, complete all as specified and as directed.

M&L for 75mm thick cement concrete (1:4:8) type D-2 (using 40mm graded stone aggregates) as in sub base of flooring even and rough, complete all as specified and as directed.

M&L for factory fabricated Hydraulically machine pressed cement concrete chequered tiles of size 300x300X25mm thick (with grey cement and pigment), set in neat cement slurry including provision of 15mm thick cement screed bedding layer in CM 1:4, tiles joints shall be grouted and immediately after grouting, the joints shall be pointed flush in separate process in CM 1:3 mixed with pigments to match the colour of the Tiles, complete all as specified and directed.

Demolition of brick work or rubbled stone masonry including all quoins, arches , pillars etc built in cement mortar including disposing off the retrieved debris outside the premises, complete all as specified and as directed.

M&L for Brickwork with fly ash Bricks, old size of class designation 75 (i.e of average compressive strength 75 Kgf/Cm2) straight or curved on plan exc 6m mean radius, built in Cement morter 1:6, complete all as specified and directed

M&L for Brickwork with sub class 'B', old size bricks of designation 75 (i.e of average compressive strength 75 Kgf/Cm2), straight or curved on plan exc 6m mean radius, built in Cement Morter 1:4, complete all as specified and directed.

All as per item No 87 above but except brick.

M&L for Brickwork with sub class 'B', old size bricks of designation 75 (i.e of average compressive strength 75 Kgf/Cm2), straight or curved on plan to any radius in half brick thick wall, built in Cement Morter 1:4, complete all as specified and directed.

All as per item No 89 above but except brick.

Taking down cement plaster on brick or concrete surfaces etc, including raking out joints, hacking for key, scrubbing down with water etc, and also including removal of rubbish off the premises, complete all as specified and directed.

M&L for rendering 15 mm thick in cement mortar (1:6), on brick work or concrete surfaces, finished even and smooth without using extra cement, complete all as specified and directed.

M&L for rendering 5mm thick in CM 1:3 on concrete surfaces of ceiling/Chajja/Facia of chajja etc, finished even and smooth without using extra cement, complete all as specified and as directed.

M&L for rendering 15 mm thick in CM (1:4) on brick work or concrete surfaces finsihed even and smooth (without using extra cement) mixed with water proofing compound as per manufacturer instructions, complete all as specified and as directed. Note:- WPC shall be measured and paid seperately.

Supply only liquid water proofing compound, complete all as specified and directed.

M&L for applying two coat of Birla/Asian wall care Putty after preparation of old/new wall/ ceiling surfaces, complete all as specified and directed.

M&L for preparing new surfaces of walls duly applied with wall care putty, applying two coats of oil bound distemper, white or any tint as approved, over and including a coat of primer, complete all as specified and directed. Note :- Provision of wall care putty not included in this item.

M&L for preparation of new or previously untreated surfaces of ceiling and applying three coats of white washing, complete all as specified and directed.

M&L for complete removal of existing treatment of walls, preparing the surfaces of walls duly applied with wall care putty and thereafter applying two coats of oil bound distemper, white or any tint as approved, over and including a coat of primer, complete all as specified and directed. Note :- Provision of wall care putty not included in this item.

M&L forcomplete removal of existing treatment of walls, preparing the surfaces of walls duly applied with wall care putty and thereafter applying two or more coats of 100% Premium acrylic emulsion weather coat paint @ 1.43 ltr/10 sqm (for two coats) paint having VOC less than 50 gm/ litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives over and including priming coat of exterior primer applied @ 0.90 litre/ 10 Sqm, complete all as specified and directed. Notes :- (i) Provision of wall care putty not included in this item.

M&L for preparation of newly surfaces duly applied with wall care putty and applying two or more coats of 100% Premium acrylic emulsion weather coat paint @ 1.43 ltr/10 sqm (for two coats) paint having VOC less than 50 gm/ litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives over and including priming coat of exterior primer applied @ 0.90 litre/ 10 Sqm, complete all as specified and directed. Notes :- (i) Provision of wall care putty not included in this item.

M&L for preparation of old treated surfaces of ceiling and applying one coat of white washing, complete all as specified and directed .

M&L for preparation of newly plastered wall surfaces and applying two coats of cement based paint, complete all as specified and directed.

M&Lcomplete removal of existing treatment of walls surfaces, preparing the surfaces of walls and applying two coats of cement based paint, complete all as specified and directed.

M&L for preparing of old steel & iron surfaces of any description, not otherwise described, over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L for preparing of old steel & iron surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coat of synthetic enamel paint complete all as specified and directed.

M&L for preparation of old treated surfaces of wall and applying one coat of white washing, complete all as specified and directed .

Dismantlingof RCC tank of any description and in any position not otherwise specically provided for and including disposing off the retrieved debris outside the premises, complete all as specified and as directed.

S&F rotational moulded polyethylene water storage tank 1000ltrs capacity, ISI marked, (cylindrical vertical type double-layered) with closed top including inlet,outlet and wash out holes, provision of G.I Fittings for fixing of the inlet, outlet and washout pipes, hoisted in position, complete all as specified and as directed.

S&F rotational moulded polyethylene water storage tank 1000ltrs capacity, ISI marked, (cylindrical vertical type double-layered) with closed top including inlet,outlet and wash out holes, provision of G.I Fittings for fixing of the inlet, outlet and washout pipes, hoisted in position and including dismantling of old one, complete all as specified and as directed.

S&F Ball valves, high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic ball, screwed for iron pipe of 20mm bore (Minimum weight 455 grms), complete all as specified and as directed.

S&F in repair Ball valves, high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic ball, screwed for iron pipe of 20mm bore (Minimum weight 455 grms), complete all as specified and as directed.

S&F in repairs stop valves, fancy type, cast copper alloy, chromium plated, screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions of 15 mm bore, complete all as specified and as directed.

S&F in repairs two bib tap, fancy type, cast copper alloy, chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or brass ferrule of 15 mm bore, complete all as specified and as directed.

S&F in repairs bib tap, fancy type, cast copper alloy, chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or brass ferrule of 15 mm bore, complete all as specified and as directed.

S&F in repairs bib tap, long Body with Wall Flange, fancy type, cast copper alloy, chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or brass ferrule of 15 mm bore, complete all as specified and as directed.

S&F in repair angle valves, fancy type, cast copper alloy, chromium plated, screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions of 15 mm bore, complete all as specified and as directed.

S&F in repairs Pillar taps with Arrestor , fancy type, cast copper alloy, with long swan neck , chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe of 15mm bore, complete all as specified and as directed.

S&F Toilet Paper holder, brass chromium plated with and including chromium plated brass screws with wooden plugs, complete all as specified and directed.

S & F in repair cast copper alloy, chromium plated, wall mixer, Non-telephonic shower system with Aerator for mixing hot & cold water, screwed down for 15mm bore iron pipe, complete all as specified and as directed.

S & F in repair cast copper alloy, chromium plated, central hole mixer, without pop up waste system with 450mm long braided hoses, screwed down for 15mm bore iron pipe, complete all as specified and as directed.

S&Fin repair brass chrome finish health faucet with 12mm dia, 1.2 m long flexible tube and wall hook, complete all as specified and as directed. complete all as specified and directed.

S&F in repair gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe of 20 mm bore, complete all as specified and directed.

S&F in repairs, vitreous china, 1st quality, squatting pan, Orrisa pattern of approx size 260 x 580 x 440mm, white with integral foot rests, 'P' trap including making connection to trap, flush pipe, anti-syphonage pipe etc, complete all as specified and directed.

S&F in repairs PVC valveless, double syphonic action type, flushing cistern, low level of 10 Litres capacity, white, with and including inlet, ball valve, float, 32mm dia flush pipe of polyethylane of low or high density or PVC, flushing bend & handles, also including brackets, suitable for both Indian Type Water Closet & Europeon Type Water Closet & making connections, complete all as specified and as directed.

S&F in repairs Vitreous China Wash Down Water closet (Pedestal Pattern) 1st quality, approx size 350x475x390mm, white (excluding flushing cistern & flush pipe) including plastic water closet seat white, closed pattern with flat bottom and cover and mild steel CP or aluminised huiging device, making connections, complete all as specified and as directed.

M&L32 mm bore Waste fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed, complete all as specified and directed.

S&F in repair vitreous china wash basin, 1st quality, white, flat back, approx size 610x480x195 mm excluding taps but including 32 mm bore brass chromium plated waste fittings, 32mm bore PVC waste pipe, MS brackets, complete all as specified and as directed.

S&F in repairs sink with drainage board made of 1.00 mm thick sheet of stainless steel (Bronze range 204 super steel : Matt) for kitchen or laboratory with and including plugs, washers, wastes; 40mm bore PVC waste pipe, also including bedding in cement mortar 1:3 on dwarf wall or including providing mild steel cantilever brackets and connecting union to pipe, overall approx size 914mm x 460mmx203mm with bowl size 405mm x 354mm x 203mm, complete all as specified and as directed.

S&F in repairs brass chromium plated shower roses, 125 mm size with or without swivel joints (including Shower Arms) to 15mm bore steel pipe or union, complete all as specified and as directed.

S&F in repair PVC connection 15 mm size with PTMT nuts of length 600 mm, complete all as specified and directed.

S&F in repair PVC connection 15 mm size with PTMT nuts of length 450 mm, complete all as specified and directed.

S&F in repairs tubular towel rail, 20mm dia, D type, stainless steel, 600mm long between flanges, complete all as specified and as directed.

S&F in repairs grating 75mm dia of SS , complete all as specified and directed.

S&F in repair 40mm bore high density polyethylene pipes (HDPE) of pressure rating 6 kgf/cm2 fixed complete to walls, ceilings or in floors etc. complete all as specified and as directed.

S&F in repairs for 75 mm bore outlet uPVC (SWR) floor trap with and including grating, also including jointing with solvent cement and provision of PCC 1:2:4 (type B-1 : using 20mm graded stone aggregates) block of required size for fixing of floor trap, complete all as specified and as directed.

S&F in repairs PVC (SWR) gully trap 125/110 mm, setting and jointing with and including solvent cement, also including provision of cement conconrete type B-1 (1:2:4) block of required size for fixing, complete all as specified and as directed.

S & F in repairs 110 mm bore uPVC (SWR) soil, waste, ventilating, rain water pipe type 'A', single socketed, (ISI Marked) in any length with and including ruber ring joints, complete fixed to wall with necessary PVC standard stay clamps etc, laid in floors/ trenches etc, complete all as specified and directed. Note :- (i) Quoted rates shall also be deemed to include for cutting of the holes (in the wall etc) where required/ directed and making good the same in CM 1:3 to match with the existing surfaces. (ii) Excavation & Earth work shall be measured & paid for separately.

S & F in repairs 75 mm bore uPVC (SWR) soil, waste, ventilating, rain water pipe type 'A', single socketed, (ISI Marked) in any length with and including ruber ring joints, complete fixed to wall with necessary PVC standard stay clamps etc, laid in floors/ trenches etc, complete all as specified and directed. Note :- (i) Quoted rates shall also be deemed to include for cutting of the holes (in the wall etc) where required/ directed and making good the same in CM 1:3 to match with the existing surfaces. (ii) Excavation & Earth work shall be measured & paid for separately.

S&F 110mm bore uPVC (SWR) bends (any radius) access door, with and including rubber ring joints, complete all as specified and directed.

S&F 75mm bore uPVC (SWR) bends (any radius) access door, with and including rubber ring joints, complete all as specified and directed.

S&F in repairs 110mm bore uPVC (SWR), junction single (single T), equal or unequal with and including rubber ring joints, complete all as specified and directed

S&F in repairs 75mm bore uPVC (SWR), junction single (Single T), equal or unequal with and including rubber ring joints, complete all as specified and directed

S&F in repairs 110mm bore uPVC (SWR), junction double (double T), equal or unequal with and including rubber ring joints, complete all as specified and directed

S&F in repairs 75mm bore uPVC (SWR), junction double (double T), equal or unequal with and including rubber ring joints, complete all as specified and directed

S&F in repair uPVC (SWR) vent cowl, 110 mm bore, complete all as specified and directed.

S & F in repairs soap dish PTMT, fixed to wall with and including plugs & chromium plated screws, complete all as specified and as directed.

S & F in repairs soap dish CP, fixed to wall with and including plugs & chromium plated screws, complete all as specified and as directed.

S&F in repair corner shelf glass with chromium plated bracket guard and railing 60cm long, complete all as specified and as directed.

S & F in repairs towel ring CP, fixed to wall with and including plugs & chromium plated screws, complete all as specified and as directed.

S&F in repair sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long, complete all as specified and as directed.

S&F in repair 40mm PCC Jafri wall fixed with 1:3 cement mortar, complete all as specified and directed.

M&L for 20 mm thick machine cut, pre-polished, black jet, premium quality, granite stone slab as in kitchen platform, cills, jambs etc, laid over and including 20mm thick Cement mortar 1:6 screed bed, jointed with grey cement slurry and pointed with white cement mixed with admixture of pigments to match with the shade of granite stone including rounding / moulding the edges half round, and including dismantling of old one, complete all as specified and directed.

M&L for plain cement concrete (1:3:6) type-C-2 (using 40 mm graded crushed stone aggregate) as in surface channel and drains including necessary form work, complete all as specified and directed.

M&L for providing 75mm thick PCC (1:3:6) type C1 (using 20mm graded stone aggregate) as in plinth protection, surface finished even & smooth without using extra cement including provision of 10 mm joints (at an interval of 3 metre and turnings) duly filled with fine sand and bitumen in the ratio of 3:1, complete all as specified and directed.

M&L for cement concrete 1:2:4 type, B1 (using 20 mm graded stone aggregates) as in copings, Chajja kerbs, benching at the junction of roof & parapet, roof kerbs, staging of water tank etc including necessary fromwork, weathering, slightly rounded or chamfered angles and throating, complete all as specified and as directed.

M&L for precast Reinforced cement concrete 1:2:4 type B-1 (using 20 mm graded stone aggrgates ) set in CM 1:4 as in landing, cover slab (for manholes, chulla hoods, chajjas, water trough, mangers, shelves and similar article with plain faces including form work complete all as specified and as directed

M&L Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-l smooth finished, and reforming benching as requiredcomplete all as specified and as directed

Demolition and breaking up drain pipes 150mm bore (Salt glazed ware, AC or Reinforced concrete) set in cement mortar including removing debries out side the MoD land complete all as specified and as directed.

M&L for 150 mm dia salt galzed stone ware (SGSW) drain pipe, grade 'A' laid in trenches and jointed complete all as specified and as directed.

M&L cement concrete 1:3:6 type C-2 for 150 mm dia in bed to drain pipes including packing under, and haunching against the sides of pipes etc complete all as specified and as directed.

Taking down existing un-servicable waterproofing treatment from roof slab surfaces (including roughening of old concrete surfaces by picking), cleaning the surfaces by wire brush and also including disposing off the retrieved debris outside the premises / site, complete all as specified and as directed.

M&L for brushing neat cement slurry with 3.00 kilogram of cement per square metre over roof surfaces etc, providing 15 mm thick plastering in cement mortar 1:4 mixed with liquid water proofing compound, finished even and smooth, complete all as specified and as directed. Note :- Supply only water proofing compound shall be measured and paid separately under the respective Item.

M & L for APP modified roof treatment over existing roof slab etc to be executed through approved authorised applicator of the membrane manufacturer with the following specifications, complete all as specified and directed:- (a) Applying oil bound bitumen primer @ 0.40 litre/ Sqm manufactured by the same manufacturer as that of APP with a density 0.87-0.89 Kg per litre at 25 degree centigrade on the prepared dry surface. (b) Laying 3mm thick APP modified water proofing polymeric membrane reinforced with non woven polyester fibre using butane torch by torch application with 10cm side lap and 15cm end lap. (c) Physical properties of membrane shall be as under:- (i) Membrane weight not less than 3.00 Kg/Sqm. (ii) Non woven polyester weight not less than 160gm /sqm. (iii) Softening point of membrane not less than 150 degree Celsius. (iv) Joint tensile strength-longitudinal not less than 650N/Sqcm and transverse not less than 450 N/Sqcm. (v) Tear strength-longitudinal not less than 300 N & transverse not less than 250 N. (vi) Elongation : > 20% in both directions. (vii) Impermeability/water tightness at 2 Kgf/cm2. (viii) Water absorption,% - Not more than 0.15. (ix) Cold flexibility - (-) 50C. (x) Dimentional stability % change = Maximum 1%. (xi) Heat Resistance - Does not dirp at 1200 C Note : The quoted rate shall also be deemed to include for cutting grooves of size and shape as required in the parapet wall for tackling the APP membrane in the wall including making good the surfaces of groove as well as damaged surfaces of the wall after tackling of membrane in CM 1:3 to match with the adjoining surfaces.

M&L for applying one coat of solar reflective bituminous aluminium paint @ 0.10 Kg/Sqm over APP membrane, complete all as specified and directed.

Dimantling of Asbestos cement (corrugated, semi corrugated, etc.) sheets in roof coverings including ridges etc, complete all as specified and as directed.

Dimantling of steel sheet (corrugated, semi corrugated, etc.) sheets in roof coverings including ridges etc, complete all as specified and as directed.

S&F pre-painted colored trapezoidal profiled Galvalume/Zincalume sheet with min 0.50mm TCT confirming to IS-513 (AZ-150 GSM, AL Zn alloy metalic coating, 550 MPA yield stress as per AS-1397), colour /exterior coat of silicon modified polyster/ BHP X RW paint system 20 micron top coat applied over 5 micron primer and a 5 micron polyster back coat applied over 5 micron primer, as in roof covering/ cladding to wall, fixed with and including Galvanised self drilling self-tapping fastener (12-14 x 55 with EPDM seals), complete all as specified and directed.

S&F pre-painted colored plain sheet profiled Galvalume/Zincalume sheet with min 0.50mm TCT confirming to IS-513 (AZ-150 GSM, AL Zn alloy metalic coating, 550 MPA yield stress as per AS-1397), colour /exterior coat of silicon modified polyster/ BHP X RW paint system 20 micron top coat applied over 5 micron primer and a 5 micron polyster back coat applied over 5 micron primer,as in roof covering/ cladding to wall fixed with and including Galvanised self drilling self-tapping fastener (12-14 x 55 with EPDM seals), complete all as specified and directed.

M&L for plain cement concrete (edges of concrete surfaces exc. 5cm and not exc 10cm thick and width of wall not exc one brick thick wall) in 1:2:4 (using 20mm graded crushed stone aggergate) as in gap between roof sheet and brick wall and finish both side of wall with 15mm rendering in cement martar 1:6 and finishes with match to existing surfaces including necessary scaffolding and formwork complete all as specified and as directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation, etc) or insulation boards/slabs/ blankets, any thickness, including cover fillets, and existing frame work also, complete all as specified and as directed.

S & F 4mm thick Non-asbestos fibre cement decorative/designer building boards (4mm thick pre-painted designed decorative type E-Board) to steel frame work with screws in ceiling (flat and/or slopping) and including jointless finish with & also including joining compound and tape as per manufacturer instructions, complete all as specified and as directed. Notes :- (i) The board shall be confirming to IS-14862 and shall be manufactured from the homogeneious mixture of cement, quartz and cellulose and shall be curred with high pressure steam using auto claving process. (ii) Steel frame work shall be measured and paid for separately.

S&F Decorated PVC False ceiling consisting of 600mmX600mmX5mm (± 0.25mm) thick plain PVC sheet of density 600 Kg/Cbm of the specified make, used as a panel insert in a frame work made using powder coated aluminum T-section of size 25mm x 25mm of 19 guage or 1mm thick in square pattern of grid size 600mm x 600mm. The aluminum frame work shall be supported from the ceiling by providing J Hook or 4 mm dia GI wire of required size to maintain the proper levels etc as directed. The aluminum frame work shall be supported on side wall with the use of powder coated aluminum Angle section of size 25mm x 25mm of 19 gauge or 1mm thick angles etc. complete all as specified and directed.

M&L decorative type plaster of paris work of size not less than 50x50mm, as in cornice or junction of wall and ceiling, complete all as specified and directed.

S&F of GI frame work (size of grid 600mm x 600mm) for seamless ceiling comprising GI perimeter channel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre, including provision of Hangers of 4mm dia G.I wire (length as required at site), complete all as specified and as directed.

S&F anodised aluminium snap grid frame work for false ceiling hangers 6mm dia GI (upto 1200mm length) adusting level fixed to roof slabs by means of ceiling cleats made out GI flat iron 40x3mm size 60mm long and fixed expansion hold fsteneners 12.5mm dia and 40mm long, complete all as specified and as directed.

M&L for preparation of new surfaces of Non-asbestos fibre cement boards as in ceiling and applying two coat of oil bound distemper over a coat of primer , complete all as specified and as directed.

M&L for RCC 1:2:4 type B1 (using 20 mm graded stone aggregates) as in landings, cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs,mangers, helves and similar articles with plain face, complete all as specified and as directed. Note: Reinforcement and Formwork shall be measured and paid for separately.

M&L RCC (1:1 1/2:3) type A-1 (using 20 mm graded stone aggregates) as in beams, cantilevers, bressummers, lintels over 1.5 m span, etc, complete all as specified and directed. Note: Reinforcement and Formwork shall be measured and paid for separately.

M&L RCC (1:1 1/2:3) type A-1 (using 20 mm graded stone aggregates) as in slabs supported on walls, beams and columns in floor, roofs, landings, balconies, canopies, deck slabs and in shelves, etc, complete all as specified and directed. Note: Reinforcement and Formwork shall be measured and paid for separately.

S&F in repair Continuous (piano) hinges [40mm width of flaps(when open)], mild steel, bright finish or electrogalvanised, complete all as specified and directed.

M&L for cement concrete 1:2:4 type B-0 (using 12.50mm graded stone aggregates) as in roof kerb,top of chajja,roof kerbs, and the like including necessary form work, complete all as specified and as directed.

Surface excavation n.exc30 cm in deep and averaging 15 cm deep in soft/ loose soil and getting out, complete all as specified and directed.

Excavation in trenches in soft/loose soil not exceeding 1.5 metre wide & not exceeding 1.5 metre in depth and not exceeding 10 Sqm on plan & not excluding 1.5 metre in depth and getting out, complete all as specified and directed.

All as per item No 185 here-in-before but exceeding 1.5 metre & not exceeding 3 metre in depth, complete all as specified and as directed

Excavation over area not exceeding 1.5 metre in depth and getting out, complete all as specified and directed.

All as per item No 187 here-in-before but exceeding 1.5 metre & not exceeding 3 metre in depth, complete all as specified and as directed

Removal of excavated material to a distance not exceeding 50 metre and depositing where directed at a level not exceeding 1.5 metre above the starting point, complete all as specified and directed.

Returning, filling in with approved earth obtained from excavation including spreading, watering and well ramming in layers not exc 25cm thick in layers, complete all as specified and directed.

M&L for plain cement concrete 1:4:8 type D-2 (using 40mm graded stone aggregates) as in foundation & mass concrete, complete all as specified and directed.

Use and waste for formwork to sides of foundation footing, plinth beam and similar work, vertical or to better in rough finished flat concrete surfaces, complete all as specified and directed.

Use and waste for formwork to sides of pllars, posts, struts, piers, columns and stanchions in rough finished flat concrete surfaces, complete all as specified and directed.

Use and waste for formwork to roof beams, lintels, cantilever, shelves including supports, overhangs etc, in rough finished flat concrete surfaces, complete all as specified and directed.

Use and waste for formwork to chullah hoods, chajjas, troughs and similar items including edges in rough finished flat concrete surfaces, complete all as specified and directed.

Use and waste for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landing and similar works, not exc. 200 mm thick in rough finished flat concrete surfaces complete all as specified and directed.

M&L RCC, M-25 (using 20 mm graded stone aggregates) as in foundation, footing foundation beams etc, complete all as specified and directed. Note: Reinforcement and Formwork shall be measured and paid for separately.

M&L RCC, M-25 (using 20 mm graded stone aggregates) as in columns, pillars, piers, posts, etc, complete all as specified and directed. Note: Reinforcement and Formwork shall be measured and paid for separately.

M&L RCC , M-25 (using 20 mm graded stone aggregates) as in beams, cantilevers, bressummers, lintels over 1.5 m span, etc, complete all as specified and directed. Note: Reinforcement and Formwork shall be measured and paid for separately.

M&L RCC M-25 (using 20 mm graded stone aggregates) as in chajja, etc, complete all as specified and directed. Note: Reinforcement and Formwork shall be measured and paid for separately.

M&L RCC M-25 (using 20 mm graded stone aggregates) as in slabs supported on walls, beams and columns in floor, roofs, landings, balconies, canopies, deck slabs and in shelves, etc, complete all as specified and directed. Note: Reinforcement and Formwork shall be measured and paid for separately.

M&L for TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia, or securing with clips etc, complete all as specified and as directed.

M&L TMT bars 8mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips etc. complete all as specified and as directed.

M&L TMT bars 8mm dia and over upto and including 10mm dia as in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips etc, complete all as specified and as directed.

M&L 40mm thick damp proof course to horizontal surfaces in cement concrete 1:2:4 type-B0 (using 12.50 mm graded stone aggregates) including necessary formwork, complete all as specified and as directed. Note:- WPC shall be measured and paid seperately.

M&L for sand filling under floors or in foundations including watering and consolidating, complete all as specified and directed.

M&L for hardcore of broken stones or boulders of gauge not exc 63 mm, deposited, spread and levelled in layers not exc 15 cm thick, watered & rammed to a true surface, complete all as specified and directed.

M&L for 100mm thick cement concrete (1:4:8) type D-2 (using 40mm graded stone aggregates) as in sub base of flooring, complete all as specified and as directed.

M&L for 25 mm thick PCC 1:2:4 type B-0 (using 12.5mm graded stone aggregates) as in sub-base of floors etc, finished even & rough, complete all as specified and directed.

M&L for 20 mm thick machine cut, pre-polished, black jet, premium quality, granite stone slab as in kitchen platform, cills, jambs etc, laid over and including 20mm thick Cement mortar 1:6 screed bed, jointed with grey cement slurry and pointed with white cement mixed with admixture of pigments to match with the shade of granite stone including rounding / moulding the edges half round complete all as specified and directed.

S&F standard aluminium powder coated section(minimum thickness of powder coating shall be 50micron and colour shall be as approved by the GE) as in frame, shutters for doors, windows / ventilators, Fixed/ Openable / side hung/ sliding two or three track or in any pattern, partitions etc, cut to size, jointed with cadmium plated steel screws, including Aluminium beading & rubber beading or gaskets for fixing glass, provision of hinges, screws, plugs, handle, lock, roller, Nylon ball bearing etc, complete all as specified and directed. Notes:- (i) Weight of Aluminium sections as per actual or as per IS or as per manufacturer, whichever is less, shall only be considered for payment. (ii) The accessories (including Aluminium mongries etc) required to be provided for windows, vents and doors as per directions of Engineer-in-charge shall be provided but weight for the same shall not be considered. (iii) Cost of all the items, accessories & Aluminium mongries required for the entire completion of the work shall be deemed to be included in the quoted rate. However glass panes, wire cloth shall be measured and paid separately under respective items.

S&F 4mm thick sheet glass of ordinary quality and glazing for steel surrounds with & including oil putty, in squares n exc 0.50 sqm in each pane, complete all as specified and as directed.

S&F 4mm thick sheet glass of ordinary quality and glazing for steel surrounds with & including oil putty, in squares exc 0.50 sqm in each pane, complete all as specified and as directed.

S&F 4.8mm thick sheet glass of ordinary quality and glazing for steel surrounds with & including oil putty, in squares n exc 0.50 sqm in each pane, complete all as specified and as directed.

S&F 4.8mm thick sheet glass of ordinary quality and glazing for steel surrounds with & including oil putty, in squares exc 0.50 sqm in each pane, complete all as specified and as directed.

Material and labour for point wiring for one light point/one fan point/one exhaust fan point /one call bell point controlled by 1 one way switch with 1.5 Sqmm PVC insulated unsheathed single core multi-stranded copper conductor (FRLS) cable 1100 Volts grade drawn through and including rigid non metallic PVC concealed conduit (medium grade) of suitable dia, (also including conduit fittings & PVC Junction boxes etc, along with 1.5 sqmm continuous PVC insulated unsheathed single core multi-stranded copper conductor (FRLS) cable for earth continuity wire, connected to earth dolly and to be terminated in and including factory made pressed steel sunken boxes (Having wall thickness not less than 1.22 mm for boxes upto a size of 200 mmX300 mm and beyond that the wall thickness shall be not less than 1.63 mm), concealed type with and including 3mm thick bakelite sheet cover for mounting switches, sockets, fan regulators etc, testing on completion also including cutting chases for concealed conduit, steel boxes etc, pinning in, making good the surfaces in CM 1:3 to match with the adjoining surfaces and including taking down old ones complete all as specified and as directed.

All as per item No 216 here-in-before but for one socket with other switch/switch socket outlet 5 amps on the same board, complete all as specified and as directed

All as per Item No 216 above but for one switch socket outlet, 5 Amp on independent board all as specified and as directed.

All as per item No. 216 here-in-before but for one light point controlled by two, 2-way switch.

All as per item No 216 here-in-before but for one 15 Amp switch socket outlet, independent with 2.5 Sqmm single core multi-stranded copper conductor cable (FRLS) along with 2.5 sqmm continuous PVC insulated unsheathed single core multi-stranded copper conductor (FRLS) cable for earth continuity wire, complete all as specified and as directed.

Material and labour for point wiring for one light point/one fan point/one exhaust fan point /one call bell point controlled by 1 one way switch with 1.5 Sqmm PVC insulated unsheathed single core multi-stranded copper conductor (FRLS) cable 1100 Volts grade drawn through and including rigid non metallic PVC concealed conduit (medium grade) of suitable dia, (also including conduit fittings & PVC Junction boxes etc, along with 1.5 sqmm continuous PVC insulated unsheathed single core multi-stranded copper conductor (FRLS) cable for earth continuity wire, connected to earth dolly and to be terminated in and including factory made pressed steel sunken boxes (Having wall thickness not less than 1.22 mm for boxes upto a size of 200 mmX300 mm and beyond that the wall thickness shall be not less than 1.63 mm), concealed type with and including 3mm thick bakelite sheet cover for mounting switches, sockets, fan regulators etc, testing on completion also including cutting chases for concealed conduit, steel boxes etc, pinning in, making good the surfaces in CM 1:3 to match with the adjoining surfaces complete all as specified and as directed.

All as per Item No 221 above but for one switch socket outlet, 5 Amp on independent board all as specified and as directed.

All as per item No 221 here-in-before but for one 15 Amp switch socket outlet, independent with 2.5 Sqmm single core multi-stranded copper conductor cable (FRLS) along with 2.5 sqmm continuous PVC insulated unsheathed single core multi-stranded copper conductor (FRLS) cable for earth continuity wire, complete all as specified and as directed.

Material and labour for sub main wiring with 2 run of single core PVC insulated (unsheathed) multi stranded copper conductor FRLS cable of size 2.50 sqmm and one single core PVC insulated (unsheathed) multi stranded copper conductor FRLS cable of size 2.50sqmm as in continuous earth wire drawn into and including concealed PVC conduit, medium grade of 20 mm bore complete with fittings, PVC Junction Boxes, fixings accessories, also including cutting chases, pinning in, making good to facing and pointing in using cement mortar 1:3 and making good disturbed surfaces to match with the adjoining surfaces and including taking down old ones, complete all as specified and as directed. Note for Item No 214 to 217:- For payment purposes, 2 runs of main cable (each of 1RM), 1 run of earth continuity cable (1RM) and one run of conduit (1RM), all together shall be considered as "1RM".

M & L for sub main wiring with 2 run of single core FRLS PVC insulated & unsheathed multistranded copper conductor of nominal cross sectional area 4.00 sqmm alongwith one run of FRLS PVC insulated & unsheathed multistranded copper conductor of nominal cross sectional area 4.00 sqmm as earth continuity conductor drawn through and including PVC concealed conduit, medium grade, 25mm bore complete with fittings, PVC Junction Boxes, fixing accessories, also including cutting chases, pinning in, making good to facing and pointing in using cement mortar 1:3 and making good disturbed surfaces to match with the adjoining surfaces and including taking down old ones, complete all as specified and directed.

M & L for sub main wiring with 2 run of single core FRLS PVC insulated & unsheathed multistranded copper conductor of nominal cross sectional area 6.00 sqmm alongwith one run of FRLS PVC insulated & unsheathed multistranded copper conductor of nominal cross sectional area 6.00 sqmm as earth continuity conductor drawn through and including PVC concealed conduit, medium grade, 25mm bore complete with fittings, PVC Junction Boxes, fixing accessories, also including cutting chases, pinning in, making good to facing and pointing in using cement mortar 1:3 and making good disturbed surfaces to match with the adjoining surfaces and including taking down old ones, complete all as specified and directed.

M & L for sub main wiring with 2 run of single core FRLS PVC insulated & unsheathed multistranded copper conductor of nominal cross sectional area 6.00 sqmm alongwith one run of FRLS PVC insulated & unsheathed multistranded copper conductor of nominal cross sectional area 6.00 sqmm as earth continuity conductor drawn through and including PVC concealed conduit, medium grade, 25mm bore complete with fittings, PVC Junction Boxes, fixing accessories, also including cutting chases, pinning in, making good to facing and pointing in using cement mortar 1:3 and making good disturbed surfaces to match with the adjoining surfaces , complete all as specified and directed.

Supply and fixing switch piano flush type, single pole, one way, 5 amps, complete all as specified and as directed.

Supply and fixing switch piano flush type, single pole, one way, 15/16amps, complete all as specified and as directed.

S&F switch, flush type, 5 Amps, SP, two way, complete all as specified and as directed.

S&F bell push, flush type, 5 Amps, complete all as specified and directed.

S&F socket outlet, 5 pin, 5 Amps, flush type, complete all as specified and as directed.

S&F socket outlet, 3 pin, 5 Amps, flush type, complete all as specified and as directed.

Supply and fixing switch socket out let multipurpose, 3 pin, 15 amp and one 3 pin, 5 amp, controlled by one switch, complete all as specified and as directed.

Supply and fix electronic fan regulator, flush type, 5 step not less than 100 watt, complete all as specified and directed.

Supply and fixing modular type switch piano single pole, one way, one module, 5 amps, complete all as specified and as directed.

Supply and fixing modular type switch piano, single pole, one way, one module, 16 amps, complete all as specified and as directed.

S&F modular type socket outlet, 2/3 pin, 5 Amps, combined 2 modules complete all as specified and as directed.

S&F modular type socket outlet, 2/3 pin, 16 Amps, combined 2 modules complete all as specified and as directed.

Supply and fix modular type electronic fan regulator, 230V,AC,50Hz not less than 100 watt, complete all as specified and directed.

S&F ceiling rose, 3 phase, PVC/ polycarbonate, isolated body, complete all as specified and directed.

S&F Buzzer Ding Dong, AC, 230 Volts, single pole, complete all as specified and directed.

Supply and Fix Lamp holder, PVC/Polycarbonate type with back plate, complete all as specified and directed.

S&F in repair LED battery backup invertor bulb of Lamp wattage 12 Watts, Battery - Not less than 2200 mAh or not less than 4 hrs backup, Efficacy - Not less than 80 Lm/Watt, complete all as specified and directed.

S&F in repair surface and wall mounted LED batten, 20 Watt, 4 ft long with aluminum housing & integrated Electronic Driver with IP20, PF 0.90, total system lumens 2200 Lumens, 6500k CRI ≥ 80, Operating Voltage range 140 V - 270 V, including provision of twisted copper conductor flexible wire from ceiling rose to connector, complete all as specified and as directed.

S&F in repair recess mounted LED down light fittiings round /square type, 15/16 Watt, indoor luminaries with including electronic driver and LED lamp, including provision of twisted copper conductor flexible wire from ceiling rose to connector, complete all as specified and as directed.

S&F LED lights fittings, 1X20 Watt, 220V, AC, decorative box type with driver, holder including LED tube light and provision of twisted copper conductor flexible wire from ceiling rose to connector, complete all as specified and as directed.

S&F LED bulb 20 Watt,, complete all as specified and as directed.

S&F LED bulb 9 Watt,, complete all as specified and as directed.

S&F in repair surface and wall mounted LED batten 10 Watt, 2 ft long with aluminum housing & integrated Electronic Driver with IP20, PF 0.90, total system lumens 1050 Lumens, 6500k CRI ≥ 80, Operating Voltage range 140 V - 270 V including provision of twisted copper conductor flexible wire from ceiling rose to connector, complete all as specified and as directed.

S&F surface and wall mounted LED batten 10 Watt, 2 ft long with aluminum housing & integrated Electronic Driver with IP20, PF 0.90, total system lumens 1050 Lumens, 6500k CRI ≥ 80, Operating Voltage range 140 V - 270 V including provision of twisted copper conductor flexible wire from ceiling rose to connector, complete all as specified and as directed.

S&F in repair LED Bulk Head fitting 10 Watt with Injection molded polycarbonate housing IP66, IK10, 3.5kV inbuilt surge protection, PF ≥0.95, total system lumens 1000 lm, 6500k CRI ≥ 80, Operating Voltage range 140 V - 270 V including provision of twisted copper conductor flexible wire from ceiling rose to connector, complete all as specified and as directed.

S&F in repair LED Street Light 20 Watt made up of pressure die cast aluminiun housing with highly efficient LEDs and PC cover with integrated lens with IP66, IK07, System Lumen Efficasy ≥100 Lm/W, 5 kV Surge Voltage Protection, Operating Voltage range 140 V - 270 V including provision of twisted copper conductor flexible wire from ceiling rose to connector, complete all as specified and as directed.

S&F LED Flood Light 100 Watt with IP66, fixed on roof truss with necessary arrangement, complete all as specified and as directed.

S&F Building Security light 1x20 watt, presure die-cast housing with individual LEDs as light source and Lens embedded PC cover having TOP opening, separate driver compartment with IP 66 protection and impact resistance of IK-07, and provision of copper conducor cable for connection, complete all as specified and directed.

S&F in repair MCB, SPN, DB, 8 ways, double door, Metal door, IP-43 IK 09 in 100A rated copper bus bars, earth bar, neutral links complete including provision of blanking plates as required & fixed flush to wall and making good the disturbed surfaces in CM 1:3, complete all as specified and directed.

S&F in repair MCB, SPN, DB,12 ways, double door, Metal door, IP-43 IK 09 in 200A rated copper bus bars, earth bar, neutral links complete including provision of blanking plates as required & fixed flush to wall and making good the disturbed surfaces in CM 1:3, complete all as specified and directed.

S&F in repair MCCB, TPN, DB,4 ways, double door, Metal door, IP-43 IK 09 in 250A rated copper bus bars, earth bar, neutral links complete including provision of blanking plates as required & fixed flush to wall and making good the disturbed surfaces in CM 1:3, complete all as specified and directed.

S&F in reapir MCCB, FP, 160 Amps, 415V, 50 Hz, 'C ' series complete all as specified and directed.

S&F in repair MCB, SPN, 40 Amps, 240V, 50 Hz, breaking capacity 10 KA, 'C ' series complete all as specified and directed.

S&F in repair MCB, SPN, 32 Amps, 240V, 50 Hz, breaking capacity 10 KA, 'C ' series complete all as specified and directed.

S&F in repair MCB SP, 10KA, 230V, C-curve, 6-32 Amps, complete all as specified and directed.

S&F MCB, SPN, DB, 8 ways, double door, Metal door, IP-43 IK 09 in 100A rated copper bus bars, earth bar, neutral links complete including provision of blanking plates as required & fixed flush to wall and making good the disturbed surfaces in CM 1:3, complete all as specified and directed.

S&F MCB, TPN, DB, 4 ways, double door, complete including provision of blanking plates as required & fixed flush to wall and making good the disturbed surfaces in CM 1:3, complete all as specified and directed.

S&F MCB, SPN, 40 Amps, 240V, 50 Hz, breaking capacity 10 KA, 'C ' series complete all as specified and directed.

S&F MCB SP, 10KA, 230V, C-curve, 6-32 Amps, complete all as specified and directed.

S&F Isolator SP, 240V, 40 Amps, complete all as specified and directed.

S&F Isolator SPN, 240V, 40 Amps, complete all as specified and directed.

S&F Isolator TPN, 415V, 63 Amps, complete all as specified and directed.

S&F in repair Isolator SP, 240V, 40 Amps, complete all as specified and directed.

S&F metal clad socket outlet with MCB single pole and neutral 20-32 Amp, 240 V including sheet metal enclosure complete fixed on flat iron 32x6 mm or 2nd class hardwood wooden board including complete electrical connection by proper size of copper lugs complete all as specified.

M&L for Earthing complete with galvanized steel earth plate electrode 600 mm X 600 mm X 6 mm thick buried directly in ground (earth pit not less than 2.25 m deep below ground level) with top edge of plate not less than 1.5 m below normal ground level, connected to galvanized iron earth lead wire of 4 Sqmm by means of bolts, nuts, check nuts and washers of galvanized iron or steel, all as shown in Electrical Plate No 3 of SSR Part - I, including necessary excavation and earth work, PCC (1:3:6) type C-1 with 50 mm thick Pre-cast RCC (1:2:4) type B-1 cover slab (reinforced with 8 mm dia deformed bar @ 15 cm C/C both ways and suitable handle of 10 mm dia round bar), including providing charcoal or coke and common salt in alternate layers of 15 cm compacted thickness all around the earth electrode, with funnel and 20 mm bore galvanized iron watering pipe (light grade), wire mesh, aluminium lugs, complete in all respect, GI earth wire protected by 15 mm bore (medium grade) galvanized iron pipe and other end connected with main switch board or Earthing test point as directed, including necessary earth work and disposal of spoil to a distance not exceeding 50 m and necessary testing on completion, including dismantling old unsv ones complete all as specified and as directed.

S&F GI tubing, light grade, 40 mm bore for protection of cable along the wall to TPN DB incliding taking out unsv one, complete all as specified and directed .

S&F in repairs, single pole and neutral enclosure, with & including a two pin and earth plug and socket, also with and including one number double pole, MCB, 20 Amps, 240 volts, 10 KA ruputring capacity, complete all as directed and specified.

S&F in repairs Exhaust fan, 300mm sweep, 230 V, Single Phase, metal body complete with and including accessories, luovers, anchoring bolts, nuts, washers, making opening for fixing of the Exhaust Fan and including cutting , making enlarging of exiting hole for fixing of exhaust fan and making good the surfaces of the opening with CM 1:3 to match with the existing surfaces and provision of PVC copper conductor cable for making connection with ceiling rose, complete all as specified and as directed. Note : The existing E.F. shall be the property of the Govt. & the same shall be deposited by the contractor in MES store yard.

S&F in repair of energy saving BLDC ceiling fan; Type of motor - Brush Less DC Motor (BLDC) and Input Power - 32 to 35 Watts with full speed and reduced power consumption with reduced speed technology, RPM - 340 to 375 rpm, Sweep - 1200 mm, Air delivery - Not less than 210 CMM and Colour - Glow white/ Toast Brown/ Gloss Black or others as approved by GE, and speed/ power control - Smart Remote control with RF/ IR/ WIFI, point anywhere technology, with multi pairing, timer and intelligent memory functions. (Remote control shall consist of heavy duty long lasting battery as per specified size) complete all as specified and as directed. Note: Old unserviceable fan shall be deposited to MES store. Quoted rate shall also be deemed to be included for the same.

S&Fceiling fan, white in colour,1200 mm sweep, 230V, SP, complete with accessories, MS hook made out of mild steel flat iron of size 25 x 5mm of the rquired length for hanging of ceiling Fan, also making connection with and including copper conductor cable from ceiling rose to fan, also including taking down of existing Fan and depositing the same in MES store yard of GE, complete all as specified and as directed, Note: Old unserviceable fan shall be deposited to MES store. Quoted rate shall also be deemed to be included for the same.

S&Fceiling fan, white in colour,1200 mm sweep, 230V, SP, complete with accessories, MS hook made out of mild steel flat iron of size 25 x 5mm of the rquired length for hanging of ceiling Fan, also making connection with and including copper conductor cable from ceiling rose to fan, , complete all as specified and as directed,

S&F Exhaust fan, 300mm sweep, 230 V, Single Phase, metal body complete with and including accessories, luovers, anchoring bolts, nuts, washers, making opening for fixing of the Exhaust Fan and including cutting , making enlarging of exiting hole for fixing of exhaust fan and making good the surfaces of the opening with CM 1:3 to match with the existing surfaces and provision of PVC copper conductor cable for making connection with ceiling rose, complete all as specified and as directed.

S&F sturdy Engineering plastic body exhaust fan, copper winding of 450mm sweep, 230 volts, AC, single phase, complete with & including accessories, louver shutters, provision of PVC copper conductor cable for making connection from existing ceiling rose, making opening for fixing of the exhaust fan & making good the surfaces of the opening with CM 1:3 to match with the existing surfaces, complete all as specified and directed.

S&F single phase KWH meter with LCD display of rating 5-30A with optical port and box including taking down old unsv ones, complete all as specified and as directed, . Note: Old KWH meter shall be deposited in MES store & quoted rate shall also be deemed to include for the above.

M&L for Earthing complete with galvanized steel earth plate electrode 600 mm X 600 mm X 6 mm thick buried directly in ground (earth pit not less than 2.25 m deep below ground level) with top edge of plate not less than 1.5 m below normal ground level, connected to galvanized iron earth lead wire of 4 Sqmm by means of bolts, nuts, check nuts and washers of galvanized iron or steel, all as shown in Electrical Plate No 3 of SSR Part - I, including necessary excavation and earth work, PCC (1:3:6) type C-1 with 50 mm thick Pre-cast RCC (1:2:4) type B-1 cover slab (reinforced with 8 mm dia deformed bar @ 15 cm C/C both ways and suitable handle of 10 mm dia round bar), including providing charcoal or coke and common salt in alternate layers of 15 cm compacted thickness all around the earth electrode, with funnel and 20 mm bore galvanized iron watering pipe (light grade), wire mesh, aluminium lugs, complete in all respect, GI earth wire protected by 15 mm bore (medium grade) galvanized iron pipe and other end connected with main switch board or Earthing test point as directed, including necessary earth work and disposal of spoil to a distance not exceeding 50 m and necessary testing on completion, complete all as specified and as directed.

S&F 4mm dia GI wire for earth continuity conductor for making connection from earth test point to main DB , complete all as specified and as directed

S&F test point terminal block made of gun metal or phosphorous bronze size 75x75x25mm, drilled and screwed 3 Nos, 8mm dia, 25mm long, hex head screw, complete all as specified and as directed

S&F porcelain vitreous white insulator, fixed on wall/roof/block with galvanised iron nuts, bolts and washers for separating the aluminium or GI strip/roof/block complete all as specified and as directed

S&F LED Street Light 35 Watt made up of pressure die cast aluminiun housing with highly efficient LEDs and PC cover with integrated lens with IP66, IK07, System Lumen Efficasy ≥100 Lm/W, 5 kV Surge Voltage Protection, Operating Voltage range 140 V - 270 V including provision of twisted copper conductor flexible wire from ceiling rose to connector, complete all as specified and as directed.

S&F street light bracket made out of 25 mm bore GI Light grade pipe 1.00 M long bent to the shape as required for steet light fittings pronded with two pairs of MS Flat Iron 50mm x 6mm clamps of required shape with nuts, bolts and washers suitable for steel tubular pole including painting of mild steel flat iron surfaces with two coats of synthetic enamel paint over a coat of red oxide primer complete, complete all as specified and directed.

Supplying, laying, jointing and testing XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cable (Heavy duty) with stranded aluminium conductor 1100 volts grade, cross sectional area 10 Sqmm 2core laid in trenches /along poles/on wall etc, complete all as specified and as directed Note For item No 278 : Excavation and earth work, sand cushioning, protection covers shall be measured and paid for separately.

Material and labour for sand cushioning for protection of underground cable consolidated and compacted with clean dry sand all as specified and as directed (Compacted thickness shall only be measured and paid)

Material and labour for well burnt Sub class 'B' old size bricks, best quality locally available laid flat, dry in trenches for cable protection, complete all as specified and as directed.

B.B.Enterprise

M/S B D ENTERPRISE

M/S R. K. INDUSTRIES

M/S TARAN INFRACON

STAR CONSTRUCTION