SPECIAL REPAIR TO BLDG NO. T-151, T-152, T-153 AND P-54 AND BLDG NO. P-117 AT KARU AREA UNDER GE 860 EWS

Amount

Roughening surfaces of old concrete floor by picking sweeping cleaning & washing down with water to remove dust etc incl removal of old treatment of any description and applying one coat of neat cement slurry @ 3.00 Kg/Sqm complete all as specified and directed by Engr-in-Charge.

M&L for rendering 15mm thick, cement plaster, in cement mortar (1:4) mixed with integral water proofing compound as per manufactures instruction, on roof slab surfaces finished even and smooth without using extra cement,complete all as specified and directed. Note:- Water proofing compound shall be measured and paid separately)

M&L for providing APP based polymeric membrane course roof treatment in layers with following provisions:- (i) Applying one coat of bitumen's primer polymerized primer oil based coat, evenly @ 0.3KG/Sqm as priming coat to the prepared surfaces, till the surfaces is properly impregnated and the solvent oil in the base primer shall be allowed to evaporated completely. (ii) Applying APP based polymeric membrane( weight not less than 3.00 Kg/Sqm) and minimum 3.00 mm thick reinforced with polyster by torch application method.

Supply only water proofing compound (integral) all as specified & directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding ( but not backing) removing dismantled tile and rubbish off the premises complete all as specified and directed by Engr-in-Charge.

M&L Non - skid coloured Ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match and joint free including 15 mm thick screed bedding in CM 1:4. for laying floor finishes receiving floor tiles complete all as specified and directed by Engr-in-Charge.

M&L Non - skid coloured Ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match and joint free including 15 mm thick screed bedding in CM 1:4 for laying floor finishes receiving floor tiles complete all as specified and directed by Engr-in-Charge.

M&L Glazed ceramic coloured tiles in vertical surface 450X 300X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match and joint free including 10 mm thick baking coat in CM 1:3 for laying floor finishes receiving floor tiles complete all as specified and directed by Engr-in-Charge.

S&F in repair SDC Laminated flooring 8mm thick of any coloured, manufactured by Direct Pressure Laminated (DPL) wherein the empty Abrasive aluminium oxide overlay alongwith metamine impregnated decorated film is directly fused with the back with flooring locking profile in designed with double click locking system on the length and single locking width alongwith desire locking strength laid over 1mm thick foam base, complete including removal of existing flooring, all as directed by the Engr-in-Charge.

Dismantling of boarding in wall/ceiling, any description, fixed in any position with nails or screws complete all as specified and directed by Engr-in Charge

M&L for readymade soft wood wall / ceiling panelling in strips of 100 mm width 10mm thickness having lounge and groove fixing arrangements fixed to wooden frame work(Size of frame work 1.2X1.2 C/C included ) as per manufacturers instruction including polishing complete all as specified and as directed by Engr-in- Charge. Note : If necessary size of the frame work/ wall paneling will be changed as per site requirement.

M&L for 2nd class soft wood fillets sectional area exc 3 and n exc 6 sqcm rectangular or triangular in section but bullnosed, splayed, chamfered or rounded on one edge of face, secured with nails or brads, complete all as specified and as directed by Engr-in-Charge.

Demolition of PCC block/ stone masonry built in cement mortar including all quoins, arches, pillars, etc, but including ashlar facings, dressed stonework and precast concrete articles in any position complete all as specified and directed by Engr-in-Charge.

M&L Precast cement concrete block masonry type C1 1:3:6 (using 20mm graded aggregate) with solid blocks, exc. 10cm in width and, setting in cement mortar 1:6 complete all as specified and directed by Engr-in-Charge.

Taking down Chowkhats or frames not exc. 1.5 sq. m each with shutters without taking of shutter from the framecomplete all as specified and directed by Engr-in-Charge.

Taking down Chowkhats or frames exc. 1.5 sq. m but n.exc 4 sqm each with shutters without taking of shutter from the framecomplete all as specified and directed by Engr-in-Charge.

S&F Plain solid straight chowkats or frame rounded or chamfered put together with glue pined at joints with 2nd class hard wood complete all as specified and directed by Engr-in-Charge.

S&F 30mm thick 2nd class hardwood Plain, framed, panelled door shutters(any number of panels), with panels of timber flat on both sides(feather edged), veneered particle board medium density, wood particle board with commercial face veneers, supplied and fitted to chowkats complete all as specified and directed by Engr-in-Charge.

S&F solid PVC door frame of size 50mm X 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tubes, as per specifications and drawing complete or as directed by Engineer-In-Charge.

S&F factory made solid PVC door shutter 30mm thick (stiles), consisting of frame made out of MS tubes for top and bottom rails MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC strip of 20mm width stuck in insde with solvent cement for stiles and plain colour PVC sheets for top rail; lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement complete all as specified and directed.

S&F MS butt hinges medium weight cold rolled mild steel size of hinges 100 mm complete all as specified and directed by Engr-in-Charge.

S&F 200 mm long Aluminium, anodised, barrel tower bolt, fixed with screws complete all as specified and directed by Engr-in-Charge.

S&F 150 mm size, Aluminium anodised handles fabricated type polished complete all as specified and directed by Engr-in-Charge.

S&F 250 mm long, aluminium alloy,anodised,sliding door bolts, with hasp, staple ( bolt type) and fixing clip of sheet, cast or extruded section and fixing bolt and sliding bolts of extruded section section or cast aluminium alloy complete all as specified and directed by Engr-in-Charge.

M&L preparation of untreated new wooden surfaces over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed by Engr-in-Charge.

Hacking out old broken glass (any thickness, size, quality or description) from from metal frame including punching or drilling out old glazing pins/spring clips and providing, complete all as specified and directed by Engr-in-Charge.

S&F 4mm thick sheet glass, ordinary quality and glazing with oil putty and glazing pins in square n exc 0.5 sq. m in each pane complete all as specified and directed by Engr-in-Charge.

S&F in repairs vitreous china water closet (Squatt Pan) Orrisa pattern 580x440 mm size pan white with front or back inlet with integral 'foot rests including provn of lime concrete bedding including connections to 'flushing cistern/pipe' including 100mm CI/PVC 'P' trap complete all as specified and directed by Engr-in-Charge.

S&F 10 Litre capacity PVC low level flushing cistern with ball valve and handle/push button 32mm dia PVC flush pipe including taking down unserviceable cistern complete all as specified and directed.

S&F in repair vitreous china wash hand basin including brackets, white size 550 x 400 mm incl cutting cutting for and pinning in ends of brackets. Including Waste fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other and fixed complete all as specified and directed.

S&F in repairs viterous china urinal, full stall type, white( excluding flushing cistern, flush pipe and waste pipe)including waste fittings etc complete all as specified and directed by Engr-in-Charge.

S&F 15mm bore Bib tap brass chromium plated fancy type with capstan head handle screwed down, screwed for iron pipe fixed in repairs all as specified and directed.

S&F in repair 15mm bore Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, fancy type with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed all as specified and directed.

S&F in repairs PVC connection 15 mm bore 450mm long with screwed socket of brass on both ends and rubber washer. Complete all as specified and directed.

S&F in repair soap dish, any type, fixed to plugs with chromium plated brass screws complete all as specified and directed by Engr-in-Charge.

S&F in repair brass chromium plated Tubular Towel rail 20 mm dia D type 60 cm long . complete all as specified and directed by Engr-in-Charge.

Taking up and down GI tubing and connection including cleaning for re-fixing or removing to store 20mm bore of pipe complete all as specified and directed by Engr-in-Charge.

Taking up and down GI tubing and connection including cleaning for re-fixing or removing to store 25mm bore of pipe complete all as specified and directed by Engr-in-Charge.

S&F 20 mm 3-layer PP-R Polypropylene random copolymer) concealed pipes SDR 7.4 (PN16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc complete all as specified and directed by Engr-in-Charge.

S&F 25 mm 3-layer PP-R Polypropylene random copolymer) concealed pipes SDR 7.4 (PN16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc complete all as specified and directed by Engr-in-Charge.

S&F rotational moulded polythylene water storage tanks 500 ltrs ( cylindrical vertical with closed top) hoisted and fixed in position all specified in SSR Part-I, including dismantling water tanks and removing to store complete all as specified and directed by Engr-in-Charge.

S&F 25mm PP-R Gate valves (brass insert) as per requirement of the site complete all as specified and directed by Engr-in-Charge.

S&F in repairs corrugated flexible PVC waste pipe 32mm dia, 800mm long complete all as specified and directed by Engr-in-Charge.

S&F 75mm dia PVC (SWR) floor trap plain with grating including jointing to waste pipe fixed in solvent cement or cement concrete 1:2:4 type B1 all as in repairs specified and directed complete all as specified and directed by Engr-in-Charge.

S&F in repair stop valves 15mm bore chromium plated, cast copper alloy screwed down high pressure fancy type with capstan head handle screwed both ends for iron pipe or for union.

Demolition of old unserviceable soakage well of any size and make good the surface by filling or removing debris/ Earth, complete all as specified and directed by Engr-in-Charge.

Excavating over areas, n exc 1.5 m deep and getting out in hard/dense soil complete all as specified and directed by Engr-in-Charge.

Excavating over areas, exc 1.5 m and n.exc. 3.00m deep and getting out in hard/dense soil complete all as specified and directed by Engr-in-Charge.

Excavating over areas, exc 3 m and n.exc. 4.50 m deep and getting out in hard/dense soil complete all as specified and directed by Engr-in-Charge.

M&L for cement concrete type D2 1:4:8 (using 40mm graded aggregate) as in foundation, filling and mass concrete complete all as specified and directed by Engr-in-Charge.

M&L for Walling of random rubble stone masonry, uncoursed, well bonded, bedded and solidly hearted, build in cement mortar 1:4 complete all as specified and directed by Engr-in-Charge.

M&L for Walling of random rubble, uncoursed, well bonded, laid dry in retaining walls, abutments and similar work complete all as specified and directed by Engr-in-Charge.

M&L for providing RCC type B-1 1:2:4 using 20 mm graded crushed stone aggregate in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like all as specified and directed.

M&L for precast reinforced cement concrete 1:2:4 type B1 (using 20 mm graded crushed stone aggregate) as in cover slab for manholes set in CM 1:4 including necessary form work complete all as specified and directed by Engineer in Charge.

M&L for formwork to soffits of suspended slabs, flat, such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) etc rough finished surfaces of concrete complete all as specified and as directed.

M&L for formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide rough finished surfaces of concrete complete all as specified and as directed.

M &L mild steel TMT bars 10mm dia and over cut to length, bent to shape required, including cranking bending spirally for hooping for columns hooking ends and binding with and including mild steel wire(annealed ) not less than 0.9mm dia or securing with clip complete all as specified and as directed.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in hard/dense soil complete all as specified and directed by Engr-in-Charge.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm. complete all as specified and directed by Engr-in-Charge.

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and directed by Engr-in-Charge.

Demolition and breaking up drain pipes (salt glazed ware, PVC or re-inforced concrete) set in cement mortar internal dia of pipe 100mm complete all as specified and directed by Engr-in-Charge.

S&F 110mm dia bore PVC (SWR) pipes single socketed in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed by Engr-in-Charge.

M&L PCC 1:3:6 type C-2 as in 110mm bore of pipe in concrete bed to drain pipes including packing under and haunching against the sides of pips after they are laid and tested complete all as specified and directed by Engr-in-Charge.

S&F 75mm dia bore PVC (SWR) pipes single socketed in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed by Engr-in-Charge.

S&F 110mm dia bore PVC (SWR) bends complete all as specified and directed by Engr-in-Charge.

S&F 75mm dia bore PVC (SWR) bends complete all as specified and directed by Engr-in-Charge.

S&F PVC(SWR) vent cowl of dia 75 mm complete all as specified and directed by Engineer in Charge.

Taking down cement plaster includiing raking out joints hacking for key and scrubbing down with water complete all as specified and directed by Engiiner-in-Charge.

M&L for rendering 10 mm thick on fair face of brick work or concrete surfaces in CM 1:6 finished even and smooth wiithout using extra cement complete all as specified and directed by Engr-in-Charge.

M&L for rendering 15mm thick, cement plaster, in cement mortar (1:4) on fair faces of brick walls or concrete surfaces finished even and smooth without using extra cement in any height, complete all as specified and directed.

M&L for rendering 5mm thick cement plaster in cement mortar 1:3 on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement on ceiling in any height complete all as specified and directed.

M&L preparation of new plastered or unplastered surfaces and applying two coats of oil bound distemper on wall over a coat of alkali resistant primer complete all as specified and darected.

M&L for preparation of new plastered surfaces of wall and applying two coats of 100 % Premium acrylic emulsion paint having VOC less than 50 gm/ltrs and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm all as per the manufacturers instructions, complete all as specified and directed by Engr-in-charge.

M&L Preparation of new plastered surfaces of ceiling and applying two coats of oil bound distemper over a coat of alkali resistant primer all as specified and directed.

M&L for preparation old surfaces of plastered or unplastered old decorated surfaces of walls by brooming down or steel wire brushing; scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying two coats of oil bound distemper on walls including cornices, pilasters etc ccomplete all as specified and directed by Engr-in-Charge.

Description all as per item Srl No. 76.00 here in before but on ceiling surfaces.

Complete removal of existing surfaces including washing rubbing down and scrapping for applying Two or more coats of 100% Premium acrylic emulsion paint on wall having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces. including Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete all as specified and directed by Engr-in -Charge.

M&L for preparation/removal of old painted steel surfaces and applying two coats of synthetic enamel paint on surface of any description over 10cm width or girth complete all as specified and directed by Engr-in-Charge.

Dismantling of wall and ceiling boards (fibre, pulp, insulation etc) or insulation boards/slabs blankets any thickness, including cover fillets complete all as specified and directed by Engr-in Charge

M&L 9 mm thick Prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with nails to timber frame work in walls complete all as specified and as directed by E-in charge .

Dismantling of timber fillets, rails, posts, rafters, purlins, etc. under 40 sq. cm in section frame work complete all as specified and directed by Engr-in-Charge.

M&L second class hard wood timber scantling plain fillets square, rectangular or triangular in section, clean sawn, secured with nails or brads, sectional area exc. 13 Sq cm n.exc 25 Sq cm secured with nails or brads complete all as specified and directed by Engr-in-Charge.

S&F 35 mm thick Plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed by Engr in Charge.

Taking down shutter of any description not exc 1 sqm each complete all as specified and as directed by Engr-in-Charge.

M&L for Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified and directed by Engr-in-Charge.

S&F 75 mm Butt hinges, medium weight, cold rolled mild steel, and fixed complete all as specified and directed by Engr-in-Charge.

S&F 150mm Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and directed by Engr-in-Charge.

Supply and fixing 3 mm sheet glass thick ordinary quality and glazing with oil putty in squares n. exc 0.5 Sqm in each pane complete all as specified and directed by Engr-in-charge.

Demolition of Cement Concrete (Unreinforced) in ground floors and pavings n exc. 15cm thickness (below or above ground level), complete all as specified and directed by Engr-in-Charge.

M&L for 75 mm thick Cement concrete type C-2, 1:3:6 (using 20mm graded crushed stone aggregate) as in floor plinth protection, finishing cement concrete surface even and smooth without using extra cement complete all as specified and directed by Engr-in-Charge.

M&L for 75mm thick PCC (1:3:6) type C2 (Using 20mm graded aggregatre) as in floor levelling without using extra cement complete all as specified and as directed.

Dismantling plain or corrugated steel sheeting any guage, thickness including nainital or similar pattern roof covering and wall cladding complete all as specified and directed by Engr-in-Charge.

S&F 0.50 mm thick Galvanised, corrugated mild steel sheeting with two corrugations side lap, fixed with coach screws and washers, in roofs, walls etc. with grade of zinc coating 275.complete all as specified and directed by Engr-in-Charge.

S&F 0.50 mm thick Plain, galvanised, mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 275 complete all as specified and directed by Engr-in-Charge.

M&L preparation of steel Surfaces new untreated surface apply one coat of red oxide,zink chrome and two coat of synthetic enamel (ordinary tint) paint any description, over 10cm in width or girth,not otherwise described complete all as specified and directed by Engr-in-Charge.

Dismantling wrougth iron or mild steel work of any description not otherwise provided complete all as specified and directed by Engr-in-Charge.

S&F Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc.complete all as specified and directed by Engr-in-Charge.

S&F in repair Door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all as specified and directed by Engr-in-Charge.

M&L for 50 mm thick PCC (1:3:6) type C2 (Using 20mm graded aggregate) as in floor levelling and finished even and fair without using extra cement complete all as specified and directed by Engr-in-Charge.

S&F in repair bib taps,15mm bore cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed by Engr-in-Charge.

M&L for preparing new surfaces of plastered or unplastered and applying three coat of white wash complete all as specified and directed by Engr-in-Charge. (Note : Ladders, scaffolding will be provided by Contractor where required)

Taking down carefully alluminium / copper point wiring complete for light, fan, socket or power point etc with fittings fixtures such as ceiling rose, holders, electric fittings, switchs, sockets, aluminium conductor cable with and incl wooden batten or FR PVC conduit and its accessories such as wooden gutties, rawl plugs, GI screws, aluminium clips, nails etc complete and removing the material from site and making good the disturbed surface of wall / floor/ ceiling etc as original i.e. brick work, plastering, white washing, OBD etc as required, complete all as specified and directed.

M&L for point wiring complete for one light point / exhaust fan point / bell point controlled by one 1-way switch/ bell push, with 1.5 Sq mm (nominal area) FRLS PVC insulated un-sheathed and stranded copper conductor cable ISI marked and PVC concealed conduit ISI marked of size 20 mm dia medium grade and PVC conduit fittings such as tees, bends, elbow, reducers with and including FRLS PVC insulated unsheathed 1.5 Sqmm copper earth wire, connecting to common earth dolly with and incl Metal flush box of suitable size for fixing modular switches / sockets etc and making good surface by wall panelling etc, complete all as directed. Note : 1. The cost of Metal flush boxes and accessories etc is deemed to be included in quoted rate. 2. In case cutting & chasing of conduit is encountered with any beam / column, the PVC casing & capping or surface conduit will be used to avoid any damage to the RCC portion. 3. No cutting & chasing shall be done on ceiling surface for laying PVC conduit for ceiling fan point wiring etc, hence the PVC casing & capping or surface conduit will be used for the same.

One light / bell / buzzer / exhaust fan point controlled by one no, 1-way, 5 Amps switch.

One socket outlet 3 pin, 5 Amps on independent board, controlled by one no 5 Amp switch.

One socket outlet 3 pin 5 amps on the same board controlled by one no 5 Amp switch.

Description all as per srl item No. 104.00 here-in-before but with 2.5 sq mm FRLS copper wire with 1.5 Sqmm FRLS copper earth wire for indpendent 15 Amp point.

S&F, in repalcement, of Switch piano type, single pole, one way, 5 amps, 230 volts, complete all as specified and directed.

S&F, in repalcement, of Socket, two-in-one, 5 pin, 5 Amp, universal type, 230 volts, complete all as specified and directed.

S&F, in repalcement, of Switch piano type, single pole, one way, 15 amps, 230 volts, complete all as specified and directed.

S&F, in repalcement, of Socket, 6 pin, 5/15 Amp, multipurpose shutter type, 230 volts, complete all as specified and directed.

S&F, in repalcement, of Ceiling rose, two to three terminals, bakelite body, 230 volts, complete all as specified and directed.

S&F, in repalcement, of LED lights fitting 1x 20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

S&F, in repalcement, of angular lamp holder, PVC/Polycaronate type with back plate suitable for 9 watt LED bulb for batten fittings complete all as specified and directed by the Engineer-in-Charge.

S&F, in repalcement, of LED bulb 9Watt complete all as specified and directed by the Engineer-in-Charge.

S&F, in repalcement, of LED lights fitting 1x 10W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed at site.

S&F, in repalcement, of LED light fitting 1x9W/1X10Wbulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable sizecomplete all as specified and directed by Engr-in-Charge.

S&F, in repalcement, of exhaust fan, steel body AC single Phase. 230V of size 300mm sweep with blades, and frame and louvers complete all as specified and directed by Engr-in-Charge. Note: Old Exhaust fan shall be deposited at MES Store.

S&F in replacement of DB, double Door, made out of CRCA mild steel sheet surface with insulated material like polyester or with epoxy powder coating and IP 43 & IK 09 protection, SPN 12 way, 240 volts with bus bar rating 200 Amps, dust and vermin proof, suitable for incorporation of MCB’s and isolators etc and making all necessary connections, duly flush of wall surface, complete all as specified and directed.

S&F in replacement of MCB, C Curve type, 10 kA, 40 to 63 Amp, SPN with over load and short circuit protection, complete all as directed.

S&F in replacement of MCB, C Curve type, 10 kA, 6 to 32 Amp, Single Pole with over load and short circuit protection, complete all as directed.

M&L for sub main wiring with 2 run of 6 Sqmm FR, PVC insulated, unsheathed and stranded copper conductor cable with and incl 6 Sqmm (nominal area) FRLS, PVC insulated, unsheathed and stranded copper conductor cable as earth wire connected with thimble from main DB to sub main DB, drawn in to separate concealed medium grade, ISI marked, non metallic PVC conduit 15 mm dia size incl all conduit accessories & fittings / junction boxes / inspection covers etc, with and incl cutting chasing and making good of disturbed surface of wall / floor/ ceiling etc as original by brick work, plastering, white washing, OBD etc as required, complete all as specified and directed by Engr-in Charge. Note : 1. The cost of concealed conduit & accessories is deemed to be included in quoted rates. 2. The two run of 4 Sqmm wire and one run of 6 Sqmm wire will be measured as one unit.

M&L for earthing with galvanized steel earth plate electrode of size 600 x 600 x 6 mm buried directly in ground earth pit not less than 2.25 mtr below of normal ground level with top edge of earth plate should not less than 1.5 mtr below normal ground level and connected to galvanized iron earth lead wire of size 4 mm dia by means of bolts, nuts, washers of galvanized iron or steel all as shown in electrical plate No.3 of MES SSR Part I connecting to earthing test point on completion with and including 15 mm bore GI light grade protection pipe (7.5 mtr long) for earth lead GI lead wire 4mm dia (7.5 mtr long), PCC pit with cover in PCC 1:2:4 type B-1 reinforced with 8 mm dia tor bars @ 80mm C/C, 20mm dia medium grade watering pipe with funnel, wire mesh, common salt, charcoal, necessary excavation and earth work, complete all as specified and directed.

S&F, in repalcement, of exhaust fan, steel body AC single Phase. 230V of size 450mm sweep with, blades, and frame and louvers complete all as specified and directed.

S&F in replacement of DB, double Door, made out of CRCA mild steel sheet surface with insulated material like polyester or with epoxy powder coating and IP 43 & IK 09 protection, SPN 8 way, 240 volts with bus bar rating 200 Amps, dust and vermin proof, suitable for incorporation of MCB’s and isolators etc and making all necessary connections, duly flush of wall surface, complete all as specified and directed.

M&L for sub main wiring with 2 run of 4 Sqmm FR, PVC insulated, unsheathed and stranded copper conductor cable with and incl 4 Sqmm (nominal area) FRLS, PVC insulated, unsheathed and stranded copper conductor cable as earth wire connected with thimble from main DB to sub main DB, drawn in to separate concealed medium grade, ISI marked, non metallic PVC conduit 15 mm dia size incl all conduit accessories & fittings / junction boxes / inspection covers etc, with and incl cutting chasing and making good of disturbed surface of wall / floor/ ceiling etc as original by brick work, plastering, white washing, OBD etc as required, complete all as directed. Note : 1. The cost of concealed conduit & accessories is deemed to be included in quoted rates. 2. The two run of 4 Sqmm wire and one run of 4 Sqmm wire will be measured as one unit.

M/s Siachen Construction Co. (BID ID -3413499)

M/S Behl Sons (BID ID -3414541)

M/S MA CONSTRUCTION Co (BID ID -3414305)

osho traders (BID ID -3414345)

M/S GEE AAR and SONS ENTERPRISES (BID ID -3413809)

Rampal Singh Contractor (BID ID -3414463)

M/S HONY CAPT RIGZIN SAMPHEL (BID ID -3414240)

M/S MOHD KARIM (BID ID -3413647)

M/S ASGAR ALI TIMBER SHOP (BID ID -3413634)