CA NO. GE/CHM-91/2025-2026 PROVN OF TOILET BLOCK AT INFANTRY BN AT CHANDIMANDIR MIL STN

Amount

Surface dressing n.exc 15cm deep in hard dense soil complete all as specified and directed

Excavation in trenches in hard/dense soil not exceeding 1.5 metre wide and not exceeding 1.5 metre in depth for foundation etc. or for shafts, wells cesspits, manholes, pier hole etc. and getting out, complete all as specified.

Excavation in trenches in hard/dense soil exceeding 1.5 metre but n.exc 3.00 metre wide and not exceeding 1.5 metre in depth for foundation etc. or for shafts, wells cesspits, manholes, pier hole etc. and getting out, complete all as specified.

Excavation over areas in hard/dense soil not exceeding 1.50 metre in depth and getting out complete, all as specified.

Excavation over areas in hard/dense soil exceeding 1.5 metre but not exceeding 3.00 metre in depth and getting out complete, all as specified.

providing cement concrete type D2, 1:4:8 using 40 mm graded stone aggregate, as in foundation, mass concrete etc., complete all as specified and as directed

Reinforced cement concrete , 1:1½:3 (nominal mix,type A-1, using 20mm graded crushed stone aggregate) as in Chajja and similar works, all as specified.

Reinforced cement concrete , 1:1½:3 (nominal mix,type A-1, using 20mm graded crushed stone aggregate) as in Beams, cantilevers, bressummers, lintels over 1.5m span , all as specified and directed.

Reinforced cement concrete, type A-1, 1:1½:3 (nominal mix, using 20mm graded crushed stone aggregate) as in foundations including rafts, footings, foundation beams, plinth beams, bases for columns etc., basement slabs, under-reamed piles and mass concrete and the like complete all as specified and directed

Reinforced cement concrete, type A-1, 1:1½:3 (nominal mix, using 20mm graded crushed stone aggregate) as in well steining and well curbs etc and the like complete all as specified and directed

Reinforced cement concrete 1:1½:3 (nominal mix,type A-1, using 20mm graded crushed stone aggregate) as in slabs supported on walls, beams etc, shelves and the like complete all as specified and directed (reinforcement shall be measured and paid for separately). Note for serial item No 7 to 11 : Reinforcement and form work shall be measured and paid separately

Form work to edges of concrete flats, treads, break in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n.exc 20cm wide and side of RCC / PCC bends in walls , horizontal or sloping and similar work.

Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter , all as specified and directed.

Form work to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. for roughly finished flat surfaces of concrete, all as specified.

Mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hoping for columns, hooking ends and binding with mild steel wire (annealed ) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

Mild steel TMT bars 6 to 8mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia. or securing with clips complete all as specified & directed. (Stirrups)

Brick work with sub class ‘B’ bricks, straight or curved on plan exc 6 metre mean radius built in cement mortar 1:6 complete all as specified & directed.

Brick work with sub class ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 complete all as specified & directed.

Brickwork with sub class ‘B’ bricks in one brick thick honey comb walling, built in cement mortar 1:4 complete all as specified & directed.

Returning filling in, including spreading, leveling, watering and well ramming in layers not exceeding 25 cm depth , complete all as specified and directed.

Removal of excavated material to distance not exceeding 50 metre and depositing where directed at a level not exceeding 1.5 metre above the starting point , complete all as specified and directed.

Earth filling under floor including spreading and levelling in in layers n.exc 25cm thick complete all as specified & directed.

40mm thick PCC 1:2:4(using 12.5mm, type B-0 graded stone aggregate) Damp proof course to horizontal or vertical surfaces including necessary formwork complete, all as specified and directed.

Applying evenly a coat of blown type bitumen at the rate of 1.50 kg per square metre and blinding with clean dry sand @ 0.05 cum per sqm complete all as specified and directed.

Rolled mild steel work as in roof trusses (framed) trussed, purlins, crane gantries, rails and fastening and heavy bracket framing (beam, tee, angle, channel or flat sections) including distance pieces, cleats etc , Gde-Fe-410-S, complete all as specified & directed.

Pre-painted galvalume aluminium zinc (AZ-70) coating GI based corrugated steel sheeting 0.50 mm thick any colour having tensile strength 550 Mpa as in roof coverings/cladding to wall, fixed with self tapping screws etc , including dismantling of old sheet of any description complete all as specified & directed by Engineer-in-charge.

Mild steel, plain, black sheet , thickness of sheet 1.6mm plain,in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required complete all as specified and directed.

Rendering 15mm thick in Cement and Sand mortar 1:4 over fair faces of brick / concrete ,finished even and smooth without using extra cement, including using water proofing compound, including necessary scaffolding & safety arrangement for plaster upto & including 4 storey building complete all as specified. Note : WPC shall be measured and paid separately.

Rendering 15mm thick in Cement and Sand mortar 1:6 over fair faces of brick/concrete surfaces ,finished even and smooth without using extra cement, complete all as specified and directed.

Glazed ceramic coloured tiles of size 300mmx450mmx 7mm thick first quality as in dado, set and jointed in neat cement slurry and grouted in white cement complete as on vertical surfaces over and including 10 mm thick bedding layer in CM 1:4 complete all as specified and directed.

Three coats of white wash on wall surfaces including preparation of new plastered surfaces complete all as specified and directed

Preparation of new plastered surfaces of walls and applying two coats of cement base paint, complete all as specified and directed.

Hard core of broken stone or boulders of gauge n.exc. 63mm, deposited, spread and leveled in layers n.exc. 15cm thick, watered and rammed to a true surface complete all as specified & directed.

75mm thick PCC 1:4:8 type D-2 (using 40mm graded crushed stone aggregate) as in sub base etc, finished even and rough complete all as specified and directed.

Non skid ceramic coloured tiles 7 to 8 mm thick square/rectangular) area of each tile exc 0.11 sqm but not exceeding 0.18 sqm, in floors etc., set and jointed in neat cement slurry and pointed in white or Coloured cement to match over and including 15 mm thick bedding layer in CM 1:6, complete all as specified and directed.

75mm thick plain cement concrete type C-1 1:3:6 (Using 20mm graded crushed stone aggregates) as in plinth protection finished fair and even without using extra cement complete all as specified and directed.

25mm thick Plain cement concrete 1:2:4 type B-0 using 12.5mm graded aggregate as in sub base of floor tile, complete all as specified & directed.

Supply only integral water proofing compound complete all as specified & directed.

Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 50 x 100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp ressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge.

Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately).

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2 , modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer?In- Charge

Supply and fixing Factory made steel window box type with side hung shutters including box type hinges, 125mm steel handle-02 Nos mild steel ISI marked tower bolt 125mm size (minimum 2 for each shutter) complete with glazing bars, dovetailed or welded fixed with and including MS flat of suitable size for fixing grills and guards bars etc complete all as specified.

150 mm size stinless steel , barrel tower bolt of extruded section and fixed complete all as specified and directed.

1400 size stainless steel finish zince chrome handle curve design complete all specified and directed

250mm stainless steel sliding door bolt with hasp, staple ( bolt type), fixed as in repair complete all as specified and directed.

Factory made box type steel ventilators including one shop coat of red oxide primer, hinges, tower bolts 100 mm, steel handles and steel peg stay complete with glazing bars devetailed or welded complete all as specified and directed.

Preparation of new or previously untreated steel surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of Synthetic enamel paint over a coat of red oxide, complete all as specified and directed.

Galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18 mm and fixed with stainless steel wire staples, complete all as specified and directed.

4mm thick figured glass pin head type glazing with oil putty in square n.exc 0.5 Sqm in each panes complete all as specified and directed.

4.8mm thick sheet glass pin head type glazing with oil putty in square n.exc 0.5 Sqm in each panes complete all as specified and directed.

PVC (SWR) pipe, 75mm bore, single socketed in any length with rubber ring joints, laid in floors in trenches, complete all as specified and directed.

PVC (SWR) rain water pipe, 110mm bore, single socketed in any length with rubber ring joints, fixed to walls with clamps of size 25mm x 3mm including nuts bolts etc, fixed as in repair complete all as specified and directed.

75mm bore PVC (SWR) bend any radius complete all as specified and directed.

110mm bore PVC (SWR) bend any radius complete all as specified and directed.

PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified and directed.

110mm bore PVC (SWR) vent cowl any radius complete all as specified and directed.

PVC (SWR) junction single, (Single T) equal or unequal 110mm dia complete all as specified and directed.

PVC (SWR) junction single, (Single T) equal or unequal 75mm dia complete all as specified and directed.

Vitreous China Wash down water closet (pedestal pattern) , white (excluding fixing bolts, flushing cistern and flush pipe) with and including PVC seat cover, complete all as specified and directed.

Vitreous china squatting pan "orissa" pattern, size 580 x 440 mm white, with integral foot rest including 'P' or 'S' trap, flush pipe (excluding flushing cistern) including connection to trap and flushing pipe complete all as specified & directed by Engineer-in-charge.

PVC valve less syphonic action type flushing cistern low level white with PVC in let ball valve, float and handle, 10 ltrs capacity and connection to pipes, set with concrete and making good to floor, fixed in repair complete all as specified & directed.

15mm dia PVC connection with PTMT nut, of length 450mm, complete all as specified and directed.

Butt hinges, cold rolled stainless steel medium weight 75mm long complete all as specified & directed.

15 mm bore Galvanized Steel tubes, medium grade including all fittings for flush pipes, water supply pipes etc., fixed to walls and ceilings or laid in floors ,including cutting chases and making good in cement mortar 1:3 complete all as specified and directed.

20 mm bore Galvanized Steel tubes, medium grade including all fittings for flush pipes, water supply pipes etc., fixed to walls and ceilings or laid in floors ,including cutting chases and making good in cement mortar 1:3 complete all as specified and directed.

Wash hand basin, vitreous china, flat back, white of size 550 x 400 mm with CP waste coupling, angle brackets, PVC connection 15mm size, 450mm long, PVC waste pipe, fixed as in repair complete all as specified and directed.

Vitreous china bowl urinal flat back, half stall type, white with grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe), complete all as specified and directed.

Vitreous china urinal partition of size 310mm x 710mm, urinal partitions slabs terminating about 40cm above floor line complete all as specified and directed.

Urinal spreader of PTMT any colour for fixing with 15 mm dia pipe. (Minimum weight 60gms) complte all as as specified and directed

Bib taps brass, fancy type, long body with wall flange, standard chromium plated, cast copper alloy with crutch or butterfly handle, screwed down for iron pipe or for brass ferrule, suitable for 15mm bore pipe, compl complete all as specified and directed.

Angular stop cock, fancy type, cast copper alloy chromium plated, screwed down, screwed both and for iron pipe or for union, suitable for 15mm bore pipe, complete all as specified and directed.

Stop valve, cast copper alloy, screwed down, high pressure with crutch or butterfly handle, screwed both and for iron pipe or for union, suitable for 15mm bore pipe, complete all as specified and directed.

Stainless steel grating 127mm size complete all as specified and directed

PVC connection 15mm size with PTMT nuts of length 450mm long complete all as specified and directed.

32mm dia PVC waste pipe with PTMT nut, complete all as specified and directed.

Towel rail 600mm long of PTMT fixed with and including chromium plated brass screws and wooden / plastic cleats (minimum weight 190gms), complete all as specified and directed.

Towel ring of PTMT fixed with and including chromium plated brass screws and wooden / plastic cleats (minimum weight 90gms), fixed as in repair complete all as specified and directed.

Soap dish of cast copper alloy, chromium plated (CP), complete all as specified and directed.

Chromium plated, fancy type shower rose with swivel joints 125mm dia with arm and fixing to steel pipe 15mm bore, complete all as specified and directed

Supply and fix corner glass shelf 300mm (with CP brass bracket) complete all as specified and directed.

Sheet glass shelf assembly consisting of 5.5mm thick sheet glass 12cm wide with CP bracket guard and railing 60cm long, complete all as specified and directed.

1000 litres capacity rotational moulded polyethylene water storage tanks (Cylindrical vertical with closed top) triple layered, screwable lid, hoisted and fixed in position, including tank nipple, PTMT 20mm bore etc, complete all as specified

Supply and fix 500 litres capacity rotational moulded polyethylene water storage tanks (Cylindrical vertical with closed top) hoisted and fixed in position, including tank nipple, PTMT 20mm bore etc, complete all as specified

Plain cement concrete 1:3:6 type C-2, using 40mm graded crushed stone aggregate as in packing under and haunching against the sides of pipes after the pipe are laid and tested including making good and preparing the existing bedding to receive new pipe complete all as specified and directed.

Precast concrete interlocking paver block, with grey cement and no pigment, design as approved, any shape and size conforming to IS 15658-2006 of 60 mm thickness, M-35 Grade, and including laid over 25mm thick sand cushioning, complete all as specified and directed

Plain cement concrete type B-1 (1:2:4) using 20mm graded crushed stone aggregate as in seismic and other similar bands, shelves, copings, bed plates, hold fast, plinth courses and the like finished fair & even, including necessary formwork complete all as specified.

PCC (1:2:4) type B-1 using 20 mm graded stone aggregate as in surface channels, benching and drains complete all as specified and directed.

Reinforced concrete pipes, 150 mm bore class NP2, laid in trench and jointed complete with collars , jointed with cement mortar inculding fitting of same grade complete all as specified and directed.

Reinforced concrete pipes, 200 mm bore class NP2, laid in trench and jointed complete with collars , jointed with cement mortar inculding fitting of same grade complete all as specified and directed.

Oxygen LDPE underground septic tank of capacity 2000 litre, designed to carry sewage and suldge water, connection etc complete all as specified and directed. MAKE : SINTEX or equivalent as approved by Engineer-in-Charge

Factory made RCC M-35 pre cast man hole covers (Medium duty), of size 600mm x 1200mm x 100mm with plain faces, including MS frame, set in position in cement mortar 1:4 complete all as specified.

Loose filling with broken bricks aggregates of gauge 80 to 150 mm in soakage pits, soakage wellscomplete all as specified and directed.

Cast iron waste and vent pipe, 100mm bore (ISI Marked) in any length with or without ears, with cement joints, fixed in walls, floors etc including necessary cutting in floor, complete all as specified and directed.

Material and labour for point wiring with approved colour code multi stranded copper conductor, PVC insulated and unsheathed FRLSH cable of size 1.5 Sqmm ,1100 volts grade, two run of single core cable for phase & neutral and one run of single core multi stranded copper conductor, PVC insulated and unsheathed FRLSH cable of size 1.5 Sqmm ,1100 volts grade for earth continuity conductor to common earth and connected to earth dolly in and including new concealed PVC conduit terminated on and including new modular sunken box and suitable size of frame, cover for mounting switch, socket and regulator fixed on surface flush with wall , comprising of One light /bell/buzzer point controlled by one switch or one fan point controlled by one switch &fan regulator, complete all as specified and directed. Note : Unit rate is inclusive of making good the disturbed surfaces by provding by wall putty/POP after mason work and finshing to match the original and nothing extra shall be paid on this account.

All as per serial item 95 herein before but for socket outlet 3 pin 5 Amps on same board complete all as specified and directed

All as per serial item 95 herein before but for socket outlet 3 pin 6 Amps on independent board complete all as specified and directed

All as per serial item 95 herein before but One socket outlet three pin ,6/16 Amp, independent board, with 2.5 Sqmm (nominal area ) FRLSH cable & 2.5 Sqmm (nominal area ) cable as earth continuity conductor

Switch modular type (ISI marked), single pole, one way 6 Amps, one module (ISI marked), complete all as specified & directed.

Switch modular type (ISI marked), single pole, one way 16 Amps, one module (ISI marked), complete all as specified & directed.

Socket shutters outlet 2/3 pin 6 Amp modular type multi purpose two module (ISI marked), complete all as specified & directed.

Socket shutters outlet 2 in 1 pin 6/16 Amp modular type multi purpose combined 2 module (ISI marked), complete all as specified & directed.

Ceiling rose, PVC or polycarbonate of size 65mmx50mm three terminals (ISI marked) all as specified and directed by Engineer-in-charge.

MCB DB, IP 43 protection, powder coated double door with locking arrangement suitable for surface and flush mounting, 08 way SPN with 200 Amps busbar 240V completed all as specified and directed.

MCB ,SP, 240 volt, 6 Amps to 32 Amps, 10 KA , 'C' series including connection with suitable size aluminium / copper lugs complete all as specified and directed

MCB, DP, 240 volt, 32 Amps, 10 KA , 'C' series including connection with suitable size aluminium / copper lugs complete all as specified and directed

LED light fitting 1x9W/1X10Wbulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

Slim LED lights fitting, 4 feet, 1x 20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

Slim LED lights fitting, mirror type with high out put diffuser 2 feet, 1x 10W, 220V, AC decorative box type with driver, holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

Sub main wiring with two single core FRLSH PVC insulated and unsheathed cable with copper conductor of size 6 Sqmm (nominal area), 1100 Volt grade(with approved colour coding as per IS) with and including continuous earth wire of size 6 Sqmm PVC insulated and unsheathed FRLSH multi stranded copper conductor 1100 volts grade , and connected to main board drawing through PVC concealed conduit 25mm size(minimum size), cutting chases in walls for PVC concealed conduit and making good the disturbed surfaces by providing by wall putty/POP after mason work and finshing to match the original surfaces and nothing extra shall be paid on this account all as specified and directed. Note : (i) For the purpose of measurement, 2 single core of 6 sqmm and one single core earth cable of 6 sqmm cable shall be considered as 1 running metre. (ii) colour code shall be Red for phase, Black for neutral and green for earth

Earthing complete with galvanized steel earth plate electrode 60cmx60cmx6.00mm thick, burried directly in ground vertically to a depth not less than 2.25m below normal ground level, with top edge of the plate not less than 1.5m below normal ground level, earth plate surrounded by 15cm thick and packed alternate layers of charcoal dust and common salt, connected with and including earth lead of GI wire 4mm dia (8 SWG) by means of bolts, nuts, check nuts and washers of galvanized iron or thimbles and other end of the earth wire connected to main switch board and protected by galvanized iron pipe light grade 15mm dia bore including watering pipe 20mm dia bore GI light grade (ISI marked) with funnel and wire mesh, including all necessary excavation and earth work, PCC chamber in plain cement concrete (1:3:6) type C-1 and pit cover of presast RCC with MS frame etc and all as shown in electrical plate No 3 of MES Sch Part-I (2009), complete including dismantling of old earthing, all as specified and directed. Note(s) :- (i) RCC pit cover shall be pre-cast of RCC (1:2:4) type B-1, 80mm thick reinforced with XPM not less than 4Kg/Sqm. (ii) PCC chamber shall be constructed 500 mm away from the edge of earth pit. (iii) Rate shall include earth lead and protection pipe of length 7.5m (iv) Earth resistance should be less than 3Ohm. In case the test results are not found below 3Ohm, complete earthing will be redone without any extra cost to Govt. (v) unit rate including protection pipe and GI wire 4.00mm dia from top to earth plate upto 7.5 meter

Exhaust fan, steel body AC single Phase. 230V of size 300mm sweep , 1400 rpm, heavy duty with, blades, and frame and louvers including grouting nuts, fastners and provision of flexible coper cable 3 core form ceiling rose to exhaust fan complete all as specified and directed.

Electric water heater(vertical type geyser), capacity 25 litre, 2 KW BEE 5 Star rated AC single phase, including MS glass lined inner tank, glass coated heating element, high density PUF insulation, Anode rod protection, heavy duty fastner not less than 100mm with suitable size of nut & washer grouted in wall with complete mason work for proper mounting of geyser fastner bolts with all accessories such as safety valve, thermostat, NRV, connection piece etc. making necessary inlet / outlet water connection, testing on load complete all as specified and directed.

LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver,including lamp bracket upto 1.5metre length as per suitable for fitting including clamp with impact and corrosion resistant including thermal management in multiple optics complete with IP 66 protection, complete all as specified and directed.

Supply and laying GI tube 40mm bore light grade for cable protection on poles/walls/under road/culvert etc with all fitting and fixture complete all as specified and directed.

40mm outer dia, double walled corrugated (DWC) HDPE duct pipe conforming to IS 14930 Part-II with anti rodent and non flame propogating properties of approved colour with fittings for cable protection from approval make complete , all as specified and directed

XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 16 sqmm,2core, laid in trenches , sleeving through pipes of fixed on poles & wall or laid under floors inlcuding jointing with suitable size of alumunium lugs as specified and directed.

M/s Hari Om Engineer and Contractor (BID ID -3451022)