StartupTN Guindy ECB Interiors

Amount

Dismantling Brick / Stone Masonry in cement mortar walls under 3m high etc., complete.

Dismantling Doors and Windows including removal of frames, hinges and fastenings etc., complete.

Dismantling Floor finish & dadooing walls in cement mortar with Mosaic Tiles / Glazed Tiles / Clay Tiles / Cuddapah Slabs etc., complete.

Labour charges for removing existing closet, washbasin and urinals etc., complete.

Precast Concrete Block Masonry using Autoclaved Cellular Aerated Concrete Block of size 600 x 200 x 200mm conforming to IS 2185 (Part 3) : 1984 with Self Curing AAC Joint Mortar for Partition Wall of non load bearing type in accordance with IS 6041:1985 including neat finishing etc., complete complying with standard specification and as directed by the TANSIDCO Engineers.

Plain Cement Concrete 1:5:10 (One cement, five crushed stone sand and ten hard broken stone jelly) using 40 mm gauge hard broken granite stone jelly for foundation including dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and including curing etc., complete complying with standard specification and as directed by the TANSIDCO Engineers. (As per TNBP No. 28)

Brick work in Cement Mortar 1:6 (One cement and six crushed stone sand) using best quality Fly Ash Brick of size 230x110x75mm with class designation of 7.5 conforming to IS 13757-1993 or IS 12894-2002 including cost of mortar plasticizer, curing etc., complete complying with standard specifications and as directed by the TANSIDCO Engineers. Brickwork shall be done as per IS 2212-1991 adopting English Bond generally, other type of bond shall be done as directed by the Executive Engineer in charge. (As per TNBP No. 31)

Brick Partition Walls of 11.50cm thickness using best quality Fly Ash Brick of size 230x110x75mm with class designation of 7.5 conforming to IS 13757-1993 or IS 12894-2002 in Cement Mortar 1:3 (One cement and three crushed stone sand) using hoop iron reinforcement if found necessary including cost of mortar plasticizer, curing etc., complete complying with standard specification and as directed by the TANSIDCO Engineers. (Hoop iron reinforcement will be measured and paid for separately). (As per TNBP No. 31C)

Reinforced Cement Concrete 1:1.5:3 (One cement, one and a half crushed stone sand and three hard broken stone jelly) using 20 mm gauge hard broken granite stone jelly for all RCC items of works excluding cost of reinforcement grill, fabricating charges centering and shuttering but including super plasticiser, laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor / roof slabs wherever necessary and bearing surfaces of walls, beams etc. shall be finished smooth with Cement Mortar 1:3 (One cement and three M Sand) and kraft paper laid over it without claiming extra etc., complete complying with standard specification and as directed by the TANSIDCO Engineers. (As per TNBP No. 30)

Supplying and erecting Centering for plane surfaces such as RCC Floor / Roof Beam, Lintels, Cantilever Beams, Bed Blocks etc. with necessary supports and strutting upto 3.60m height in all floors with all cross bracings using MS Sheets made of 10 gauge thick welded with MS angle of Size 25mm x 25mm x 3mm for boarding laid over Steel Adjustable Span of size 2m x 2m (expandable upto 3.60m) and Silver Oak Joists of size 10 x 5 cm spaced at 50cm to 60cm c/c and supported by Steel Adjustable Telescopic Props of size 2m x 2m (expandable upto 3.60m) made with outer steel pipe with dia 50mm (3.60mm thick) and inner steel pipe with dia 40mm (2.90mm thick) spaced at not more than 50 to 60cm c/c etc., complete complying with standard specifications. Steel Adjustable Span and Steel Adjustable Telescopic Props shall be provided as directed by the TANSIDCO Engineers. (Payment for centering shall be given after the concrete is laid). (As per TNBP No. 86 & 86A)

Plastering the surface of walls with Cement Mortar 1:5 (One cement and five crushed stone sand), 12mm thick including mortar plasticizer at 200ml per 50Kg of cement used, curing etc., complete complying with standard specification and as directed by the TANSIDCO Engineers. (As per TNBP No. 56 & 57)

Flooring with Brick Jelly Concrete 1:2:5 (One of cement, two of crushed stone sand and five of aggregate) using brick jelly of size 20mm including labour charges etc., complete complying with standard specification.

Paving the floor with best quality Double Charged Vitrified Tiles of size 800 x 800 x 10mm and variety conforming IS 15622 with water absorbtion less than 0.08% of approved colour and shade laid over cement mortar bed of 20mm thick in Cement Mortar 1:3 (One cement and three crushed stone sand) with required Cement Slurry and Mortar Plasticizer in all floors and the top pointed with Water Resistant Tile Epoxy Grout etc., complete complying with standard specification and as directed by the TANSIDCO Engineers. (The make and brand of the tiles should be got approved by the Executive Engineer before use on works). (As per TNBP No. 39A)

Flooring with Designed Colour Ceramic Tiles of size 305 x 305 x 6mm and variety conforming to IS 15622 laid over cement mortar bed of 20mm thick in Cement Mortar 1:3 (One cement and three crushed stone sand) with required Cement Slurry and Mortar Plasticizer including cutting the tiles to the required size with special cutter wherever necessary, laying in position and pointing with Water Resistant Tile Epoxy Grout at the rate of 0.27 Kg / sq.m etc., complete complying with standard specification and as directed by the TANSIDCO Engineers. (The make and brand of the tiles should be got approved by the Executive Engineer before use on works). (As per TNBP No. 39A)

Dadooing walls with best quality Double Charged Vitrified Tiles of size 600 x 600 x 8mm conforming to IS 15622 in Cement Mortar 1:2 (One cement and two crushed stone sand), 10 thick with mortar plasticizer and pointing the joints with Water Resistant Tile Epoxy Grout at the rate of 0.27 Kg / sq.m neatly in all floors, curing etc., complete complying with standard specification and as directed by the TANSIDCO Engineers. (The make and brand of the tiles should be got approved by the Executive Engineer before use on works). (As per TNBP No. 39A)

Painting two coats of newly plastered wall surface with ready mixed Plastic Emulsion Paint of first class quality and approved colour over a priming coat including thorough scrapping, clean removal of dirt wherever required and two coats of wall putty etc., complete complying with standard specification and as directed by the TANSIDCO Engineers. (As per TNBP No. 66A)

Fabricating Supplying and fixing in position of Aluminium anodised Powder Coated (any colours) of single leaf fully glazed Door shutters with 5.50 mm thick glass. The outer frame shall be with aluminium box section 101.60x44.45x3.18m at 2.319kg/m and Shutter frame made of section with Vertical & Top rail: [email protected] kg/m, Bottom rail: 100x44.45x2.50mm@ 1.974 kg/m, Lock rail : 50x44.45x2.5mm @ 1.292 kg/mAlu. Clips: 17.15x17.27x1.50mm @ 0.176 kg/mAlu. Handle: 100x30mm @ 0.988 kg/m and necessary accessories such as Alu. clips rubber beading, full length of handles on one side, lock, furniture fittings such as, Hinges, rubber bush, including cost of materials, labour charges and power consumption charges required for fabrication including chipping, dismantling and making hole to the required extent in RCC column, beam masonry with power drill wherever necessary and redoing the damaged portion to the original condition after fixing etc. complete. All the Alu. Section are to be anodised with matt finish under electrically controlled condition in accordance with IS 1868/1962 for an average anodic film thickness of 15 microns etc., complete.

Supply & fixing of WPC door shutter, extruded as a single core board with rigid WPC compound with the thickness of 25mm (+/- 1mm) & minimum Bulk Density of 550 KG/Cub.Mt. & shore hardness of 55. The door shall be a plain matt board as decided by the Engineer in-Charge of the department. The WPC door shall be fixed onto the Aluminium “G” type channel with Wheel and the door shall have 2 Hooks in SS, 2 Handles 4” in SS (Sliding door) etc., complete and and as directed by the TANSIDCO Engineers.

Gypsum Board Partition : Supplying and fixing of 10 mm thick Gypsum Board Partition to a thickness of 50 mm which includes double side parition and providing 25 x 25 mm steel tube. The rate shall include the cost of gypsum board including making holes,cutouts, patch fittings, necessary hardwares, applying sealants, wastage etc, as required for completion the works and as directed by Engineer-in-charge.

Supplying and fixing Gypsum Board false ceiling including cost of all GI metal frame suspensions, Gypsum board and labour charges etc complete as directed by the Engineer- in - Charge.

Supply, Installing, testing and commissioning of Wash Hand Basin with all accessories such as Cast Iron Brackets, 32mm dia CP Waste Coupling, Rubber Plug and Chain, 32mm dia pvc Waste Pipe, 15mm dia brass ball Valve,15mm dia Nylon Connection, 15mm dia Brass Nipples,15mm CP sensor Pillar Tap etc White without Pedastal a) Under Counter Basin size: Parryware - Model : Wash Basin - C04711C - INDUS 500 X 400 - CTH ULTRAWHITE b) Supply ,Installing, testing and commissioning of Bottle Trap Bottle trap - T3201A1 - BOTTLE TRAP LIGHT c) Supply ,Installing, testing and commissioning of SS Waste Coupling Waste coupling - T9899A1 - Full Thread Waste Coupling- 80mm d) Supply ,Installing, testing and commissioning of Angle Valve - Angle cock - T9880A1 - Cute Angle Valve

Supply, installation and fixing of stainless steel body liquid soap dispenser with PVC rawl plug & C.P. brass screw complete as required. (Material : SS 304, Dispense : Foam soap, Battery : 4 x AA alkaline duracell, sensing distance : 5-9cm, Dispense volume : 1-2ml) Make : Make : Euronics -ES802F

Supply, Installing, testing and commissioning of stainless steel sink without drain board , with 15m dia CP sink Cock , CP waste coupling, 32mm dia CP bottle trap with extension pipe, supporting CI bracket to support sink, and CP wall flanges, all complete set of approved make. . (Pantry) Make :Hafelei Stainless Steel splash Sink a) Supply ,Installing, testing and commissioning of Angle Valve - Angle cock - T9880A1 - Cute Angle Valve b) Supply ,Installing, testing and commissioning of Bottle Trap Bottle trap - T3201A1 - BOTTLE TRAP LIGHT c) Supply ,Installing, testing and commissioning of SS Waste Coupling Waste coupling - T9899A1 - Full Thread Waste Coupling- 80mm Make / Model : Parryware T4621A1 - Claret Wall Mounted Sink Cock

Supply and fixing in position of best Indian make White Glazed earthernware lipped mouth flat back Urinal of best quality and approved make of size 430mm x 260mm x 350mm with GI pipe, 32mm dia bell mouth PVC connection and waste pipe, 15mm dia GI pipe of required length, 15mm dia GM wheel valve, 15mm dia brass nipple 2 Nos. and fixing the urinals in position with necessary TW plugs, clamps, screws etc., including dismantling masnory and re-doing the same to the original condition etc., including painting the pipe with two coats of best quality approved synthetic enamel paint over one coat of red oxide primer and checked without any leakage etc., complete complying with standard specifications and as directed by the TANSIDCO Engineers. (The urinal should be got approved by the Executive Engineer before use on works). (As per TNBP No. 102 & 103)

Supplying and fixing in position White Glazed European Water Closet of best quality and approved make with 100 mm “P” or “S” trap connecting with CI pipe of 100mm dia / PVC pipe of 110mm dia, double flapped rigid PVC black seat and seat cover with CP brass hinges including cost of white cement, cement for packing, spun yarn, teak wood plugs, brass screws etc., including supplying and fixing 10 litres capacity PVC flushing tank fixed onto wall etc., complete with all fittings such as 15mm brass ball valve with polythene float with brass handle, union, coupling connected by means of 40mm white PVC flush hand using Indian adopter joint including all internal fittings such as 15mm brass connections, 15mm GM wheel valve, 15mm brass nipple (2 Nos.), 15mm nylon connection, TW plugs, screws and also giving necessary connection to the PVC pipe including cost of 600mm length of 110mm dia PVC pipe, dismantling the masonry and re-doing the dismantled masonry to original condition etc., complete complying with standard specifications. (The EWC and flushing tank with all accessories should be got approved by the Executive Enginer before use on works). (As per TNBP No. 102 & 103)

Supplying and fixing in position of Chromium Plated Two Way Bib Cock with Health Faucet of approved make conforming to BIS specifications and quality including cost of shellac, thread, cutting and threading wherever necessary etc., complete complying with standard specification. (Cocks should be got approved by the Executive Engineer before use on the works).

Supplying and fixing in position of Special Type Mirror of size 1000 x 780mm of approved quality, brand and colour fixed with brass screws, teakwood plugs including labour charges etc., complete complying with standard specification.

Supplying, fixing and testing of approved make of 6kg / cm2 PVC pipes confirming to IS 4985-2000. and fittings (moulded and fabriacted fittings ) such as tee, elbow, 'y' , coupler, etc confirming to IS 7834 with latest amendment for soil and waste pipe works in toilets etc. Pipes shall be laid in under floors/ under ceiling / sunken floor as per approved drawings. For laying the pipes in walls, before chasing, the pipe line routing shall be marked using chalk line with help of tube level,Pipes and fittings shall be cleaned with pipe cleaners and joined by approved approved make solvent cement. After laying the pipes, before closing the pipes, gravity test to be conducted and got the approval from the engineers in charge.

75mm dia

110mm dia

Providing & fixing in position deep seal multiway PVC floor Trap of size 100 x 75mm with cockroach trap and PVC extension piece of required length depth to suit site conditions and multiple inlets, to suit site conditions with inlet sizes ranging from 40 mm to 75 mm. The bottom of the sump shall be dummied water tight. Wherever, sumps are shown to have water seal, the seal depth shall be minimum 40 mm. The sump shall be laid in cement concrete bed with 1:2:5 mix with 40 mm brick jelly bed all around and finished with cement mortar 1:3. Providing and fixing heavy class C.P. brass mosquito proof grating with frame of approved design including setting in floor with cement mortar to match with floor finish. (Sample should be got approved ) include urinal trap

Supplying and fixing in position first quality and approved variety of 25mm Dia Gun metal gate valve / wheel valve with BIS make including cost of shellac, thread balls, etc., complete complying with standard specifications ( for both internal and external water supply arrangements). the valves to be used on work shall be got approved by the executive engineer before use on work.

Linear Workstation - Workstation Area - Sharing Size : 1200x 600 x750mm Table Top is made up of 25mm thick PLPB Table Top with 2mm PVC Edge Banding . Understructure : MS Powdercoated Legs 40 x 40 Slant legs. Wire Management : Grommet Hole -65mmDia 250mm ( Ht ) Raceway below the table top Main Screen : 18mm Thick & 300mm(ht) fabric magnetic privacy with rubber beading. CENTER T LEG : MS 40X40 MS 40X40 Square leg with CRCA Pipe of 1.6mm thickness of 60 microns Powder coated leg for Table top Stability. Passage side modesty : MS powder coated 450mm(ht)

3 DRAWER PEDESTAL UNIT Size : 450x 450 x650mm Top & Sides: 18mm Thk pre laminated particle board Back: 6mm Thk pre laminated particle board Edge: All exposed area with 2mm thick PVC edge lipping FASCIA: 18mm Thk pre laminated particle board - 2 equal drawers, 1 file drawer. Boxing sliding : Telescopic channels Handle: I type handle Lock: Key lock

WORKSTATION CHAIRS. AURA - Medium Back •Sturdy 50mm G.F Nylon dual- wheel Castors , •Glass Filled Nylon Base , •Class 4 Gas lift as per DIN Standards 4550: 2004-12 , •Single Position Locking Synchro Mechanism , •Height Adjustable 2D PU Armrest, •Glass Filled Nylon Backrest with Mesh , •Seat Upholstered with PU Foam & Fabric , • Height Adjustable Lumbar Support.

Visitor Model Meshback Chair S type Fixed Handle

Cabin Table: Main Table Size - 2100 x 100 x 750mm Side Storage Size - 2000 x 500 x 750mm Back Storage Size - 2700 x 450 x 750mm Main & Side table Specifications: Top panel: 25mm Thk pre laminated particle board Edge: All exposed area with 2mm thick PVC edge lipping LEG : Slant or Straight leg 40*40mm size tube, tube thickness 1.6mm with powder coating finished. SUPPORT BEAMS : 40*40mm ms tube with 1.6mm thickness and with ms powder cioating finished. MODESTY : 1.2mm Thk ms modesty panel with powder coating finished in 400mm height. Flip cover 400mm PLB SIDE & BACK STORAGE UNIT: Top & Sides: 18mm Thk pre laminated particle board Back: 6mm Thk pre laminated particle board Edge: All exposed area with 2mm thick PVC edge lipping FASCIA: 18mm Thk pre laminated particle board. Handle: I shape handle Lock: Key lock

Main Chairs: Imported Half Leather Chair Fixed handle,Synchro Tilting Mechanism,Imported Gaslift,Chrome base,Heavy

BOARD ROOM CHAIRSWEBSTAR: Medium Back with Adjustable Handle & softpad with Chrome Base,Heavy Wheel, Synchro Tilting Mechanism,Molded Foam & Fabric

Conference Table: Size - 3150 x 1200 x 750mm TABLE TOP :25mm Thick Pre Laminated particle Board with 2mm PVC edge banding on all side with Flip Cover Hole Provision. (400mm Flip Cover). LEG : Slant type Legs, Tube thickness 1.6mm with ms powder coating finish. Cable entry Box Provided. Supported Cross Bar 40*30mm Size tube with 1.5mm thick sheet and powder coating finish. Below Table top Box Type Raceway.

Training chars with writing pad

Low Height Storage: Size - 5750 x 600 x 750mm PLB STORAGE UNIT Specifications: Top & Sides: 18mm Thk pre laminated particle board Back: 6mm Thk pre laminated particle board Edge: All exposed area with 2mm thick PVC edge lipping FASCIA: 18mm Thk pre laminated particle board Handle: I shape handle Lock: Key lock

Full Height Storage: Size - 1650 x 450 x 2100mm PLB STORAGE UNIT Specifications: Top & Sides: 18mm Thk pre laminated particle board Back: 6mm Thk pre laminated particle board Edge: All exposed area with 2mm thick PVC edge lipping FASCIA: 18mm Thk pre laminated particle board Handle: I shape handle Lock: Key lock

Pantry Unit: Size - 6000 x 600 x 800mm Supply and installation of Counter for Pantry and Cafeteria, The storage of countertop to be made of 19mm BWR ply with necessary. The storages to be with shelves, made of 19mm thick BWR ply with swing shutters with all necessary accessories like concealed auto closing SS hinges,

3 Seater sofa for reception

Fabric seater with cushion and with wooden legs for CEO room

Center Table: Size - 450mm dia, 400mm height Table top 18mm thick prelam particle board with edge banding finish. Leg 20mm square ms leg with powder coating finish.

Center Table: Size - 600mm dia, 400mm height Table top 18mm thick prelam particle board with edge banding finish. Leg 20mm square ms leg with powder coating finish.

18mm thick writing board of size 1200 x 1500mm with ms movable stand.

Transportation, loading and unloading charges

Boson Infra India Private Limited (BID ID -1549923)

MRP Constractors (BID ID -1550189)