PROVN OF TOILET BLOCKS AND ALLIED WORKS INCLUDING SEPTIC TANK NEAR BLDG P-19, P-112, T-182 AND T-169 IN CERTAIN AREA AT MIL STN POKARAN UNDER AGE (I) POKARAN

Amount

Excavation in trenches n.exc 1.5m deep and n.exc 1.5m wide ,etc. n getting out avg Soil

Surface excavation n exc 30 Cm and average 15 Cm deep and getting out in soft soil.

Returning filling in soil including spreading, levelling and well ramming in layers n.exc 25cm thick in layer etc all complete.

Removing excavated material n exc. 50 m and depositing where directed at a level n exc. 1.5 m above the starting point

Removing excavated material to a distance exc 100 mtrs but not exc 250 Mtrs and depositing where directed.

M&L for PCC ( 1:4:8) Type D-2 using 40 mm graded aggregate as in fdn

M&L For Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick spread, levelled and rammed including watering

M&L for Hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and as directed.

M&L for 75mm thick PCC 1:4:8 Type D-2 using 40mm graded stone aggregate as in sub bases all as specified.

M&L for squared rubble walling, Jodhpur type, brought upto courses, well bonded, bedded and solidly hearted, built in cement mortar (1:6) all as specified & directed by Engineer-in-charge.

Extra over stone walling for hammer dressing to face stones with maximum depression on face from a straight edge not exceeding 20mm & dressing face beds and joints as specified to squared rubble walling Jodhpur type brought up to courses all as specified & directed by Engineer-in-Charge.

M&L rendering 15mm thick in 1:6 cement plaster on stone masonary surface is to be finished even and smooth (without using extra cement) complete all as specified and directed.

M&L rendering 15mm thick in two layers 10 mm & 5 mm respectively in CM (1:4) cement plaster on of stone masonary surface is to be finished even and smooth (without using extra cement) complete all as specified and directed.

M&L for 5 mm thick , plaster in cement mortar (1:3) on surfaces of ceiling and finishing the surface even and smooth without using extra cement all as specified & directed by Engineer-in-charge.

M&L preparation of new wall surface and applying three coats of white wash on wall complete all as specified and directeded.

M&L for preparation of new plastered surfaces as in ceilings, applying 3 coats of white wash complete.

M & L for preparing new surfaces (plastered/ unplasred) of walls and applying two coats of cement base paint.

M&L for jodhpur stone roof slabs, self faced 7.5cm to 10cm thick, 25cm to 35cm wide, hoisted, set, jointed and grouted in lime mortar 1:3 or cement mortar 1:6 complete complete all as specified and as directed by the Engineer-in-Charge

M&L for PCC 1:2:4 type BO using 12.5 mm graded stone aggregate for levelling course for consolidated thickness shall be varied from 50 mm as per the requirements all as directed by Engr-in-Charge.

M&L rendering 15mm thick in 1:4 cement plaster on roof surface by using WPC Compund and surface finished even and smooth complete all as specified and directed.

Supply only integral water proofing compound.(ISI Marked)

M&L for painting with hot blown type bitumen conforming to IS 702 grade 85/25 @ 1.20 Kg/Sqm over & including a coat of bituminous primer conforming to IS-3384 applied @ 0.40 Lit/Sqm including cleaning of plastered surface and applying APP modified polymeric membrane with centre core of 20 micron HMHDPE & outer film 20 micron each, thickness 1.5mm having weight of 2.25 kg/Sqm and last coat of bonding material using semi hot blown type bitumen 85/25 grade confirming to IS-702 applied @ 1.20 kg/sqm and dusted with fine sand and including PCC 1:2:4 type B1 using 20 mm graded stone aggregate over roof and finished the surface even & fair with using extra cement. PCC shall be laid in slope of consolidated average thickness of 50 mm and V shaped groove of 6mm wide & 10mm deep & laid @ 0.60mtr interval in both ways or part thereof on top of PCC padding & groove to be filled with mastic bitumen. all as specified & directed by Engineer-in-charge.

S&F for Non- skid ceramic coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with screed bed 15 mm thick CM 1:6 complete all as specified & directed

M&L Glazed ceramic coloured tiles in vertical surface 600mm x300mm , 7-8mm mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match including 10mm thick rendering CM1:4 complete all as specified and directed.

S&F PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, supplying and fixing in opening as per Engr - in - charge.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail and bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in MS frame welded/ sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement, suplying & fixing in the frame at site as per directed by Engr - in- charge.

S&F SS hinges, 100mm size and fixed.

S&F Aluminium anodised, barrel tower bolt of extruded section and fix of length 125mm

S&F Aluminium handles, cast type, anodised of size 150mm long.

S&F 250mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and directed.

S&F Factory made Box Type steel ventilators fixed type, incl with one shop coat of primer,complete as shown in Drawing No. CEJZ/TD/24 sh 1/1 to 1/3, and all as specified & directed.

S&F figured glass, pin head type & glazing with oil putty in square n exc 0.5 sqm in each pane 3 mm thick

M&L for roughly squared stone 5cm thick as in lintels n exc 3m in length, hammer dressed on face and soffits, hoisted, set and pointed in lime mortar 1:3 or cement mortar 1:6 complete all as specified and as directed by the Engineer-in-Charge

M&L for 5cm sand stone slabs in sunshades, chajjas, shelves, cills, landings, cover stones, templates etc, n exc. 2m in length, punched dressed on face and along exposed edges, self faced on other side and set and pointed in lime mortar 1:2 or cement mortar 1:4, complete complete all as specified and as directed by the Engineer-in-Charge

M&L for 50 mm thick PCC (1:3:6) type C-1 using 20 mm graded stone aggregate laid in alternative bays as in plinth protection including finishing the surface even & fair & filling the joints with mastic filling i.e one part of bitumen 85/25&3 parts of sand by weight all as specified and directed by Engr-in-charge

Supply and fix rotational moulded polyethylene water storage tanks ( cylindrical vertical with closed top ) hoisted and fixed in position all as specified in SSR part-I ,1000 ltr capacity

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth

S&F Medium grade GI tubing 15 mm bore with all fittings , to walls, ceiling or laid in floors etc.

S&F Medium grade GI tubing 20 mm bore with all fittings , to walls, ceiling or laid in floors etc.

S&F gun metal globe or gate valves with iron wheel head screwed both end for iron pipe and fixed to 15 mm bore pipe.

S&F gun metal globe or gate valves with iron wheel head screwed both end for iron pipe and fixed to 20 mm bore pipe.

S&F stop cock copper alloy but fancy type and chrominum plated screwed down high pressure with crutch or butterfly handle screwed both ends for iron/pipe or for union and fixed 15 mm bore in repairs

S&F bib taps cast cipper alloy chromoum plated fancy type with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed in repairs

S&F Viterious china White Wash Hand Basin fixed includign 15 mm pillar cock cast copper alloy CP, 15mm cast copper stop valve, 32 mm brase CP waste fitting, PVC waste pipe 32 mm dia & 15 mm PTMT connection pipe 450 mm long

S& F Soap dish, any type, fixed to plugs with chromium plated brass screws

S&F towel rail 600 mm long of Brass C.P 'D' type fixed with and including chromium plated brass screws and wooden /plastic cheats in repairs

S&F Brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixed to 15mm dia bore.

S&F CP Shower rose 125mm size with swivel joint including fixing sted pipe for union.

S&F for European type water closet,including plastic seat cover white, closed pattern with flat bottom and mild steel chromium plated or aluminium hinging device complete.

S&F CP Health faucet spray with 1.5m long pipe with wall hook & fixed in repair complete

Supply and fix Bib taps two way type , cast copper alloy with crutch or butterfly handle, sc-rewed down, screwed for iron pipe or for brass ferrule 15 mm bore and fixed

S&F PVC connections 15 mm size with PTMT nuts to length 450 mm

S&F PVC flushing cistarn 10 ltrs capacity ISI marked incl PVC damtake pipe PVC 450mm inlet etc all complete .

Cutting holes in to or through in brick or stone walls built in cement mortar and making good in CM 1:3 or cement concrete 1:2:4 type B1 as required, exc 150sqcm & n exc 400 sqcm complete all as specified and directed,

PVC (SWR) floor trap, plain with grating including jointing with solvent cement 75 mm dia out let

PVC (SWR) multi floor trap with grating including jointing with solvent cement 100 mm dia out let.

S&F PVC (SWR) pipes of 110 mm dia, single socketed fixed to walls

S&F PVC (SWR) pipes of 75 mm dia, single socket fixed to walls

S&F 100 bore of pipe stack clamps out of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof.

S&F PVC (SWR) bends with access door of 110 mm dia, any radius

S&F PVC(SWR) bends with access door of 75 mm dia, any radius

S&F PVC (SWR) bends of 110 mm dia, any radius

S&F PVC (SWR) bends of 75mm dia, any radius

S&F PVC (SWR) vent cowl, 100 mm dia

Framed work such as grills, gratings, etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe Fe 290 Gde E-165

M&L for Granite(of any type) 18 to 20 mm thick work (table rubbed and polished) in steps, jambs, pillars, window- cills,cooking platfoRms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade

PCC 1:3:6 type C-1 using 20mm graded stone aggregate as in coping etc and like, including weathering, slightly rounded or chamfered angles and throating as directed with and includings necessary fro work complete.

M&L for PCC ( 1:2:4) type B-1 using 20mm graded stone aggregate as in surface channels & drains etc.

Extra over for forming fair finished drain or channel 30cm inner girth in cement concrete using extra cement, including form, moulds, mitered/stopped ends etc.

M&L for reinforced concrete NP2 drain pipes 150 mm dia confirming to IS laid in trenches and jointed in CM 1:2 all as specified & directed by EIC

M&L for PCC bed to drain pipes including packing under und haunching against the sides of pipes after they are laid and tested in PCC 1:4:8 type D-2 for 150mm bore pipe.

M&L for point wiring with PVC unsheathed cable single core stranded copper conductor 1.5 sq mm size, 1100 V grade, drawn into concealed conduit medium grade (ISI marked) not less than 20mm dia on surface with and including PVC unsheathed cable single core copper conductor 1.5 Sq mm as continuous earth wire and including pressed MS sheet sunk in box 1.12 mm thick with 2.8 mm thick laminated bakelite sheet all as specified & directed by Engr-in-charge for the following :-

(a) One light/Exhaust point controlled by one switch 5 Amp one way

(b) -Ditto- all as per item no 5.but socket outlet 3pin 5 amps same board

Supply and Fix switch piano type single pole one way 5 Amp

Supply and Fix sockets outlet 2 in 1, 3 Pin, 5 Amp

S&F MCB DBs sheet metal enclosures single phase and neutral 240 Volt with 200 Amps rated bus bar Double Door Type, 6 ways complete all as specified & directed

M&L MCB SP 240 volts, 5 to 40 Amps, 10 KA

M&L MCB SPN 240 volts, 40 Amps, 10 KA

M&L Lamp holder PVC polycarbonate type with back plate and LED lamp 09 watt suitable for batten fittings complete all as specified and as directed

S&F LED light 1X22 watt, including connecting up with twin core twisted flexible copper conductor cable with suitable size complete all as specified and directed by Engineer Incharge

M & L for earthing complete with galvanized steel earth plate electrode 600x600x6.3 mm thick, burried directly in ground (earth pit not less than 2.25 mtr deep below ground level) with top edge of the plate not less 1.5 mtr deep below normal ground level connected to GI earth wire 4 mm dia connected to earth plate by means of nut, bolts, check nut & washer of galvanized iron or of steel, GI earth wire will be protected by 15 mm dia GI pipe 'light grade', watering pipe 20 mm dia GI 'light grade', GI wire meshed funnel, alternate layer of char coal and salt on all side to earth plate upto thickness of 150 mm, filling of black cotton soil in earth pit upto ground level, PCC chamber recessed for and including RCC cover including all necessary excavation & earth work, earth wire connected to O/H continious earth wire on pole, testing the earthing after completion all as specified and shown in electric plate No 5 of MES SSR Part-I 1991 print and as directed .

Supply and laying in trenches/ throught pipes/ ducts or on poles/ wall jointing to O/H conductor, LT panels main switch with cable size aluminium conductor, 1100 volts grade all as specified

S & F LED building Security light fitting 1x20 watt with polycarbonate housing ,Aluminum gear tray duly prewired inbuilt LED module IP 65 Protection complete with all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable of size 1.5 sq mm including GI tubing 40mm dia light grade 1.5m long band to shape for mounting of security light with 2 nos MS,FI clamp including plinth with nut bolts etc complete all as specified and directed

M/s Shri Inder Construction Company