RENOVATION OF SDDPC AT VIRUDHUNAGAR,DEVAKOTTAI,GDPC AT KARAIKUDI

Amount

Clearing Light Jungle

Removal of Doors and windows inclding remval of frames, hinges and fastenings

Dismantling clearing away and carefully stacking materials useful for Clean removal of Cement plaster and stacking carefully away from the site for reuse etc, complete

Dismantling, clearing away and carefully stacking materials useful for re-use for any thickness of wall in Brick Masonry in cement mortar under 3m height.

Earth work excavation for foundation in all soils and sub soils except rock requiring blasting to full depth as may be directed inclusive of shoring, strutting and baling water wherever necessary including refilling the sides of foundation with excavated earth in layers of not more than 20cm thick well rammed, watered and consolidated and depositing the surplus earth within the compound in places shown by the Departmental Officers with an initial lead of 10 metres and lift of 2 metres and clearing and levelling the site etc. complete complying with standard specification.

Supplying and filling the foundation and basement with filling M Sand in layers of not more than 15cm thick well rammed, watered and consolidated as directed by the Departmental Officers complete complying with standard specification.

Providing and placing in Position of Plain cement concrete 1:4:8 (one part cement, four part fine aggregate & eight part coarse aggregate) using hard broken stone aggregate of maximum nominal size of 40mm by mixer machine including dewatering the placement site,laying the concrete in layers and in bays ,compacting and finishing the surface with all leads and lifts watering curing to attain the profile and strength as specified for various depth and height and above ground level etc complete as directed by the Engineer in charge of work complying with the standard specification

Brick work in Cement Mortar 1:5 using best quality II class table moulded chamber burnt bricks of size 9"x4⅜"x2¾" for foundation and basement including curing etc complete complying with standard specification

a) For foundation and Basement

b) For Ground Floor

Brick Masonry in cement mortar 1:6 using Second Class Ground Moulded Chamber Burnt Bricks 9" x 4 3/8" x 2 3/4" including finishing and curing as directed by the Departmental Officers complete complying with standard specification.

For foundation & basement

In Ground floor

Plastering in Cement Mortar 1:3, 12 mm thick including finishing,curing using mixer machine for mixing mortar etc,complete as directed by the engineer incharge of works and as per technical specfication.

Plastering with cement mortar 1:5 (One cement and five M sand) 12mm thick in all floors including finishing and curing as directed by the Departmental Officers complete complying with standard specification.

Paving the floor with best quality stain free nano polished vetrified Tiles of size 600 x 600 x 8mm of approved colour, shade and quality laid in cement mortar 1:3 (one cement and three sand) 20mm thick in all floors and the top pointed with the white cement mixed same colour pigments etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Paving the floor with cement based Hydraulically Pressed anti skid tiles (like Eurocon Tiles) in all floors 20mm thick

Dadooing the walls with Colour Glazed Tiles of size 300x200x6mm of approved quality laid in cement mortar 1:2 (One cement and two sand) 10mm thick and pointing with white cement using 0.40Kg.of white cement per square metre including cost of tiles, all materials, incidental charges, transportation charges and labour charges for fixing tiles neat finishing the joint flush curing as directed by the Departmental Officers complete complying with standard specification. The tiles should be got appproved by the Departmental Officers before use on work.

FRP door shutter with FRP door Frames made out of FRP Sheets of 3 mm thick of over all size 65 mm x 50 mm with rebate suitably reinforced using MS Angles / Flats, cost of hold fasts and solid core FRP shutter panel of 5mm thick and hollow core frames of 3 m wall thickness for styles and rails etc. of sizes specified by Engineers.

Supplying and fixing in position glazed steel louvered ventilator with side central hung shutter (two Leaves) frame and made shutter frame made out of steel section

Fabricating Supplying and fixing in position of Aluminium anodised natural colour matt finish of single leaf door with half panelled with 12mm thick both side laminated particle board at bottom and half glazed using 5.50mm thick Plain glass at top.B3538and Shutter frame made of section Vertical & Top rail: 50x44.45x2.50mm @ 1.292 kg/m ,Bottom rail: 100 x44.45 x 2.50mm@ 1.974 kg/m, Lock rail : 50x44.45x2.5mm @ 1.292 kg/m, Alu Clips: 17.15x17.27x1.50mm @ 0.176 kg/m,Alu. Handle: 100x30mm @ 0.988 Kg/m and necessary accessories such as aluminium clips, rubber beading, PVC felt, handle for a length of shutter (both sides), locking arrangements, furniture fittings such as aluminium tower bolts-250x12mm - 1 No., aluminium tower bolt 200x12mm - 1No., aluminium Hydraulic door closer - 1No ., lock-1No., Door stopper with rubber bush including cost of materials labour charges and power consumption charges required for fabrication including chipping, dismantling and making hole to the required extent in RCC column, beams, masonry with power drill wherever necessary and redoing the damaged portion to the original condition after fixing etc., complete. All the Alu. Section are to be anodised with matt finish under electricaly controlled conditions in accordance with IS 1868/1962 for an average anatic film thickness of 15 microns etc., complete.Aluminium sections,and furniture fittings shall be got approved by the Executive Engineer incharge.

Supplying , fabricating and fixing in position Aluminium Anodised natural colour mat finish Two track sliding window in all floors with Aluminium sections of outer Frame bottom 62x37mmx1.50mm at 1.218 kg/m,the Side & Top 62x31.50x1.50mm at 0.778 kg/m,Shutter Top 40x18x1.5 at 0.38 kg/m,Bottom 40x18x1.5 at 0.38kg/m, Side Vertical 40x18x1.50mm at 0.493 kg/m, Vertical locking section 40x29x1.5mm at 0.632 kg/m, with necessary accessories such as rubber beadings, special hinges, lock, handle including supplying and fixing 4mm thick plain glass including cost of all materials , labours, power consumption required for fabrication , drilling holes in RCC colunm, slab, masonry walls wherever necessary with power drills to the required extent and make good to the original condition after fixing and also as directed.The aluminium sections are to be anodised with matt finish under electrically controlled in accordance with IS 1868 / 1962.

Supplying laying and jointingUPVC pipe of approved quality and best variety confirming to ISS mark of the following sizes including cutting, threading and fixing GI specials including cost of GI specials and fixing to the wall with the necessary TW plugs, PVC clamps, Screws etc., making good the dismantled portion to original condition with necessary brick work and plastering wherever necessary with necessary scaffolding charges.(AGL)

20mm dia UPVC Pipe

Supplying and fixing in positionUPVC.specials of heavy type of approved quality and good variety of various sizes including necessary cutting and threading of G.I.Pipes for jointing the specials and providing two coats of painting with good variety and approved quality of synthetic enamel paint over a coat of priming coat in case of pipe line above ground level and one coat of tar in case of pipe line below ground level for both internal and external water supply arrangements.

20mm dia Elbow

20mm dia Tee

Supplying, laying and jointing PVC soil pipes of approved and best varietyconforming to IS.Specification with ISI.mark of the following sizes including, cutting and threading of PVC.Pipes, fixing specials but excluding cost of such specials but including fixing to wall with necessary teak wood plugs, PVC.clamps and screws making holes on the wall (or) drilling holes in roof and making good the dismantled portion to original condition with necessary brick work and plastering wherever necessary with necessary scaffolding charges.The PVC.Pipes should be got approved by the Departmental Officers before use on work.

160mm dia pvc pipe

110mm dia PVC pipe

Supplying and fixing in position PVC specials such as plain bend and shoe of various sizes of best approved quality conforming to ISS.and providing leak proof joints including fixing to wall and giving connection to the PVC. Pipes including,dismantling the brick masonry/RCC.floor or roof slab and redoing the disturbed portion to original condition etc.complete as directed by the Deptl.Officers complete complying with standard specification.

110mm dia PVC Bend

110mm dia PVC Door Tee

110mm dia PVC "Y"

75mm dia PVC door Elbow

75mm dia PVC Door Tee

Supplying and fixing in position 15mm dia Chromium Plated brass screw down tap

Supplying and fixing in position best quality approved make white glazed earthenware hand Wash basin

Supplying and fixing in position Indian water closet Oriya type of size 580x440mm white glazed earthen ware of approved quality size 580x440mm white glazed with ‘P’ trap or ‘S’ trap conforming to IS: 2556-part XII with sand cushion and forming flooring

Supplying and painting the walls with two coats of cement paint over one coat of cement primer as instructed by the departmental officers including preparation of surface curing, and including cost of primer etc. complete in all floors complying with standard specifications (The colour and shade of the cement paint shall be got approved by the Executive Engineer before use of work).

Supplying and painting the walls with two coats of oil bound distemper over one coat of water based cement primer including cost for distemper, primer, cleaning and scrapping the walls, rendering the walls smooth with necessary putty, brushes, scaffolding arrangements, labour charges, etc., as per standard specification. (The colour and shade of the distemper shall be got approved by the Executive Engineer before use of work).

Painting two coats with ready mixed Exterior emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification.

Painting wood work with two finishing coats of synthetic enamel ready mixed paint of approved quality and colour over one coat priming coat in all floors including the cost of primer etc., complete complying with standard specification. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)

Painting iron works two coats with synthetic enamel paint of approved quality and colour etc., complete complying with standard specification. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)

Manufacturing supplying and fixing of steel door with the following specification MS angels of size 40x40x6mm are used for the outer frames and M.S. angles of size 35x35x6mm for the shutter frames stiffeners with 32 x 6mm M.S flat is provided at required intervals in the shutter frame. 18-gauge C.R. sheet laid as panel in the shutter and welded intact. M.S. flat 18x5mm is welded over the 32 x 6mm M.S. flat sandwitching the C.R. sheet in between additional stiffeners with 18x5mm M.S. flat is provided diagonally at the rear side of the shutter, 3nos. of hinges in case of single leaf and 6nos. of hinges in double leaves shutter to be provided 6nos. of holdfasts 120 mm in length made of angle section spliced at the ends are welded to the outer frames of the door. Tower bolts 2nos. one at the top and the other at the bottom are provided 1no.

Aldrop is provided incase of double leaf door at lock rail section in the door in single leaf door, one more aldrop is provided in the inner lock rail section of the door One rotaing locking arrangements for the inner side of the door and additional provision for locking arrangements for lock is provided on the rear side of the door at an appropriate place. Incase of double leaf door M.S.Flat 32 x 3mm at 1.1Kg/m is provided on the one shutter t conceal the gap between the two shutters.at an appropriate place in the door. A tie bar is provided at the bottom of the frame to prevent twisting of frame during transportation and fixing. All members are given a coat of red oxide primer as directed by the departmental officers. The rate includes cost of all materials, labour charges, transportation to site of work, loading, un loading and all other incidental charges etc., complete.

Painting new iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with two coats of best approved first quality and colour of synthetic enamel paint over the existing red oxide priming coat in all floors excluding cost of priming coat etc., complete complying with standard specification. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)

Labour charges for fixing aluminium doors, windows and ventilators

Supplying and fixing in postion of Aluminium anodised natural colour matt finish Openable Cupboard of size 1.20x2.10 m in all floors fixed with 12 mm thick Prelaminated particle board (Exterior grade ). the outer frame of section 38x33x2.12 mm @ 0.706 kg/m, shutter frame of 38.5x33x3 mm @ 0.706 kg/m, Interlocking mullion vertical section of 59x33x2.5 mm @ 1.135 kg/m. The shutter is fixed with 6 nos. Aluminium hinges, 100x30 mmof 2 nos. D Type handle 100 mm long and 2 nos. of Cupboard lock etc. with necessary furniture fittings including cost of, labours, power consumption charges required for fabrication including necessary chipping, dismatling and making necessary holes in the RCC columns beams, masonry etc., with power drill to the required depth and redoing the same to the original condition after fixing etc., complete. complying with standard specification.

Supplying and fixing colour galvanum sheet roof of 0.47mm thickand steel tubular box section of 100x50x3mm of 1meter interval including priming coat fixing in position with all necessary accessories complete complying with standard specification

Supply and run of 2 of 4sq.mm. (56/0.3) PVC insulated SC unsheathed copper conductor of1100V on 7/20 GI bearer wire for service connection mains mains

Supply and run of 2 of 4sq.mm. (56/0.3) PVC insulated SC unsheathed copper conductor of 1100V grade in 25mm dia GI pipe (Class'B') suitably bent at both ends with necessary angle iron upright and end supports for mains

Supply and fixing of TNEB meter board suitable for 32A single phase service connection with 32A fuse unit (500V) 32A neutral link and earthlink (1"x1/8"copperflat) on TW plank of size 375mmx300mmx19mm with supporting TW reepers of 1" thick an either side with painting with suitable bolt and nuts for fixing the TW plank on wall with earth connection and inter connection with 7/20PVC insulated copper wire from EB meter to fuse unit

Supply and fixing of 32ADP switch of 500V with metal clad with fuse and neutral(sidehandle) on suitableTWboard with earth connection only

Supply and fixing of 15A aerial fuse unit (500A) on suitable100x100mm TW concealed box with hylem sheeton on the tapping pole with necessary clamps

Earthing as per PWD standard with an earth electrode of 2 metre Class'B' GI pipe of dia not less than 32mm complete with necessary masonry work

Supplying and fixing fine polished cuddapah slab of following thickness for cup-board arrangements including laying to correct alignment with necessary cement mortar and black powder etc, complete complying with standard specification and as direct by the departmental officers

Supplying and fixing 1200mm AC celling fan with regulator (crompton creaves )

Supplying and fixing Tube light (As Per Electrical Data SD 87)

Supplying and fixing approved best quality brass CP towel rail 600mm long and 20mm dia with brackets of same materials including cost of teak wood plugs and CP screws, etc., complete complying with standard specifications. (The tower rail should be got approved by Executive Engineer before use on works).

Supplying and fixing best approved best quality brass CP soap tray of size 150 x 150mm including cost of teak wood plugs, brass screws, etc., complete complying with standard specifications. (The soap tray should be got approved by Executive Engineer before use on works).

Supply and installation of Air Conditioner with copper coil - 1.5 tons with 3 star rating DDPC

Supply and installation of 4 KVA capacity Automatic Voltage Stabilizer with time delay relay (V-Guard /Equivalent)

Supply and fixing of MS stand for fixing outdoor unit

20A DP Plug and socket in sheet steel enclosure [Legrand / (MDS) / Hager (L&T)]

Supply and run of 2 of 4sq.mm .(56/0.3) PVC insulated SC unsheathed copper conductor of 1100V grade insuitable PVC rigid pipe on wall and ceiling with continuous earth wire connection of 14SWGTC wire with painting of suitable colour

KAMESWARAN