SPECIAL REPAIRS TO BUILDING NO P-179 COMMAND PRINTING PRESS AND CERTAIN MINOR WORKS AT HQTC BANGALORE

Amount

Demolition of unreinforced concrete as in roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work, complete all as specified and directed

Cement concrete 1:2:4, type B1 (20mm graded stone aggregate) as in padding over roof, roof kerbs or mud stops, rounded or chamfered on edges, complete all as specified and directed

Taking down old damaged existing water proofing membrane of any thickness from roof top, complete all as specified and directed. Note: All debris and rubbish shall be removed from MOD land during or at the end of each working period at his risk and cost in accordance with all applicable federal, state, and local regulations.

20mm rendering in two layers as 15mm thick and 5mm thick of CM 1:3, top 5mm thick layer will be mixed with liquid warer proofing admixture as per manufacturer instructions, complete all as specified and directed Note: Liquid WPC shall be measured and paid separetaly)

Supply only liquid water proofing compound, complete all as specified and directed

Water proofing treatment on horizondal or vertical surfaces by applyong oil bound bitumen primer & 0.20 Kg/Sqm and providing 4 mm thick APP modified water proofing membrane weighing not lesss than 4 Kg/Sqm reinforced with non-woven polyester matt weighing not less than 160 gm/sqm having softening point not less than 150 centigrade, having tensile strength of 650 N/5 cm and 350 N/5 cm in longitudinal and transfers directions respectively of the reinforcement tearing strenght of 180 N by torch on application including minimum 10 cm side lap and 15 cm end lap torch sealed and bonded and finished with solar reflective bituminus aluminium paint/primer @ 0.1 Kg/Sqm over RCC roof slab/ projection/ parapet after cleaning the surfaces by removing dust dirt etc as manufactures instructions, complete all as specified and directed.

PVC (SWR) pipes 150mm bore, single socketed, in any length with rubber ring joints, fixed to wall, fixed as in repais, complete all as specified and directed

Bands, straps, supports or stays for rainwater, ventilating pipes,including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges:large hasps and staples; chains; hand made sliding bolts; clamps;hold fasts; wall ties; hooks forhanging fans; plain angle cleats for securing purlins to woodtrusses or rafters; knee pieceinserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165, complete all as specified and directed

150mm bore PVC (SWR) bends of any radius, fixed as in repairs, complete all as specified and directed

Demolition of cement concrete (unreinforced) in ground floors and pavings n exc 15cm thickness (below or above ground level), complete all as specified and directed Note: All debris and rubbish shall be removed from MOD land during or at the end of each working period at his risk and cost in accordance with all applicable federal, state, and local regulations.

25mm thick Cement concrete type B-0, 1:2:4 (12.5mm graded stone aggregate) as in flooring . padding concrete, complete all as specified and directed

75mm thick Cement concrete type C-2, 1:3:6 (40mm graded stone aggregate) as in flooring, foot path, hard standing, plinth protection, bases of water tanks etc., complete all as specified and directed

Precast cement concrete 1:3:6, type C1(20mm graded stone aggregate) as in Kerb stone/bond stone apex stone bed plate, watertroughs and the like including weathering, slightly rounded or chamfered angles and throating, complete all as specified and directed

Prepolished coloured Machine pressed precast conctete interlocking paver block rubber moulded with gray cement and pigment any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade and including 40mm thick sand cushion including dismantling the existing unserviceable paver block, complete all as specified and directed

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises, complete all as specified and directed Note: All debris and rubbish shall be removed from MOD land during or at the end of each working period at his risk and cost in accordance with all applicable federal, state, and local regulations.

Non - skid ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed of CM 1:6, complete all as specified and directed

Glazed ceramic coloured/ digital wall tiles in vertical surface 350x250x7mm/ 450x300x7mm/ 450x350x7mm thick, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10 mm thick rendering on brick work or concrete surfaced wall as backing coat of cement mortar 1:4, complete all as specified and directed

Joint free non skid Ceramic tiles light shade 7 to 8 mm mm thick (square/ rectangular) polished, area of each tiles exe 0.18 Sqm but not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed of CM 1:6, complete all as specified and directed

All as Srl per item No 18 here in before but as in skirting over and including 10mm thick rendering on brick work or concrete surfaced wall as backing coat of cement mortar 1:4, complete all as specified and directed

Dismantling stone slabs and tiles of any description or thickness laid, bedded and pointed in any mortar in floors, aprons, skirting etc, complete all as specified and directed

Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete over and including 15mm thick screed bed of CM 1:6, complete all as specified and directed

Kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete over and including 10 mm thick rendering on brick work or concrete surfaced wall as backing coat of cement mortar 1:4, complete all as specified and directed

Taking down chowkats or frames with shutters (without taking off shutters from the frames) not exc. 1.5 sq. m each, complete all as specified and directed

Solid PVC frame (Single Rebated) of size 60mm x 30mm made out of solid PVC foam with homogenous fine cellular structure having smooth outer integral skin with suitable metal stiffner and fixed with 100 x 8 sheet metal CSK screws, complete all as specified, as shown on drawing and directed (Note :- Door frame shall be water proof, termite proof, elegant and should have excellent screws holding strength to fix hinges and hold doors properly for a long life)

Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet 12mm thick to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site, complete as all specified, as shown on drawing and directed.

100mm long Butt hinges, medium weight, cold rolled mild steel, complete all as specified and directed.

125mm aluminium anodised barrel tower bolts of extruded section and fixed, complete all as specified and directed

125mm Aluminium handles, cast type anodised, complete all as specified and directed.

Tubes 15mm bore, `medium grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors including taking up or down old unserviceable steel tubing, complete all as specified and directed.

All as per Srl item no 29 here in before but 20mm bore of steel pipe, complete all as specified and directed.

All as per Srl item no 29 here in before but 25mm bore of steel pipe, complete all as specified and directed.

PVC (SWR) pipes 110mm bore, single socketed, in any length with rubber ring joints, laid in trenches or in floors, fixed as in repairs, complete all as specified and directed.

PVC (SWR) pipes 110mm bore, single socketed, in any length with rubber ring joints, fixed to wall, fixed as in repairs, complete all as specified and directed.

PVC (SWR) bends 110mm bore of any radius with access door, fixed as in repairs, complete all as specified and directed.

PVC (SWR) bends 110mm bore vent cowl, fixed as in repairs, complete all as specified and directed.

PVC (SWR) 'S' trap 110mm bore, fixed as in repairs, complete all as specified and directed.

Grating doom 100mm dia of PTMT (Minimum weight 25gms), fixed as in repairs, complete all as specified and directed.

PVC (SWR) 110mm bore floor trap, plain with grating including jointing with solvent cement, fixed as in repairs, complete all as specified and directed.

15mm Bib taps, chromium plated, fancy type, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule, fixed as in repairs, complete all as specified and directed.

Pillar tap,cast copper alloy, with capstan head, chromium plated, fancy type screwed down high pressure,with or without lettered "Hot" or "Cold" with long screwed shank and fly-nuts, screwed for iron pipe, fixed as in repairs, complete all as specified and directed.

Concealed/angle stop valve 15mm bore, fancy type chromium plated with long shank and cup screwed down, high pressure with crutch or butterfly handle, for iron pipe or for unions, fixed as in repairs, complete all as specified and directed.

PVC connections 15mm size with PTMT nuts of length 600mm, fixed as in repairs, complete all as specified and directed.

Low density polyethylene (LDPE) pipes 32mm dia, of pressure rating 6 kgf/sq. cm, fixed as in repairs, complete all as specified and directed.

Brass chromium plated tubular towel rail, 20mm dia, D type, 60cm long between flanges, fixed as in repairs, complete all as specified and directed.

Soap dish, any type of size approximate size 160x 60x90mm, fixed to plugs with chromium plated brass screws, fixed as in repairs, complete all as specified and directed.

5mm thick mirror of size 450mm x 600mm mounted on 6mm thick commercial ply wood backing and screwed with PVC channel alround, fixed as in repairs, complete all as specified and directed.

Vitreous china wash basin, size 550 x 400mm white including brackets, and waste coupling & pipe of 32mm dia, brass, chromium plated for glazed ware sinks, basins white or tinted, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other, fixed as in repairs, complete all as specified and directed.

Vitreous china wash down water closet pan (pedestal pattern), (flushing cistern and flush pipe), including plastic water closet seat, white or tinted, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device, fixed as in repairs, complete all as specified and directed.

15mm two in one Bib taps, chromium plated, fancy type, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule, fixed as in repairs, complete all as specified and directed.

Hand Shower (Health Faucet) with 8mm Dia, 1 Meter Long Flexible Tube & Wall Hook, fixed as in repairs, complete all as specified and directed. Make Cera, Parryware, Somany, Jaguar or equivalent.

Supply only PVC valveless, syphonic action type, flushing cistern of 10 litres capacity, low level, white, with inlet, ball valve, float and handle including brackets and flush pipe of polyethylene of low or high density of PVC, 32 mm dia, for low level cistern ,complete all as specified and directed.

Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe 25mm dia, fixed as in repairs, complete all as specified and directed.

Vitreous china urinals half stall urinal type(back or corner wall type) complete including providing and fixing plugs bedding urinals against wall in cement mortar 1:2 securing urinals to plugs with and including 60 mm long brass screws, pointing around urinal back in cement fixing automatic flushing cistern with brackets flush pipe grating and union for discharge pipe (Exclusive of fixing supply pipe to flushing cistern trap and waste pipe), fixed as in repairs, complete all as specified and directed.

Curved shaped frameless urinal partition with 8 mm thick frosted glass of size 450mm x 900mm with CP brackets 04 Nos, fixed as in repairs, complete all as specified and directed.

Demolition of Brickwork or stone/ boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dresses stonework and precast concrete articles, complete all as specified and directed. Note: All debris and rubbish shall be removed from MOD land during or at the end of each working period at his risk and cost in accordance with all applicable federal, state, and local regulations.

Pre-cast cement concrete block type C1 1:3:6 (20mm graded stone aggregate) masonry with solid blocks, exc. 10cm in width and setting in mortar 1:6, complete all as specified and directed.

Providing precast cement concrete solid building blocks type C1 1:3:6 (20mm graded aggregate) 10cm thick (with plain or interlocking joints as directed) setting in mortar 1:4 in walls, complete all as specified and directed.

Taking down cement or cement lime plaster, any description on brick or stone walls, etc. Including racking out joints, hacking for key, scrubbing down with water, etc., complete all as specified and directed. Note: All debris and rubbish shall be removed from MOD land during or at the end of each working period at his risk and cost in accordance with all applicable federal, state, and local regulations.

Rendering 15mm thick on fair faces of brick works or concrete surfaces in CM 1:6 and finished even and smooth without using extra cement, complete all as specified and directed.

Preparing new plastered on wall and applying three coats of white wash, complete all as specified and directed.

Two coats of Distempering wall with distemper oil emulsion white or tinted over a coat of 2mm thick wall care putty, including preparation of new surface, complete all as specified and directed.

Rendering 5mm thick cement plaster in cement morter 1:3, on concrete sufaces as in ceiling, finished even and smooth without using extra cement, complete all as specified and directed.

Preparing new plastered on ceiling and applying two coats of white wash, complete all as specified and directed.

Preparation of old decorated plastered or unplastered surface of walls including scraping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots etc. and applying two coat of white washing, complete all as specified and directed.

All as per Srl item No 64 here-in -before but two coats of white washing on ceiling, complete all as specified and directed.

Two coats of Distempering wall with distemper oil emulsion white or tinted over a coat of 1mm thick wall care putty, including preparation of old surface after complete removal of existing treatment, complete all as specified and directed.

Complete removal of existing treatment of walls and applying two coats of exterior emulsion paint (weather coat) over a coat of approved primer, complete all as specified and directed.

Preparation of old painted surface of any description not otherwise described wood and wood based surfaces over 10 cm width of girth and applying one coat of synthetic enamel paint, complete all as specified and directed.

Preparation of old painted surface of any description not otherwise described steel and iron surface over 10 cm width or girth and applying one coat of synthetic eanmel paint, complete all as specified and directed.

Removing old dumped junk/ building materials/ debris/ tree roots, trunk, & branches of any size etc. to a distance of 30Km or beyond, out of premises of metropolitan area, including loading, unloading by manually or by mechanical means (JCB) and to be transported through tractor-trolly or tipper and stacking at the destination, complete all as specified and directed.

Dismantling structural steel work including doors, grill and gates but excluding framed truss etc., complete all as specified and directed.

Framed work as in grills ,railing and similar work with ends of bars shouldered and /or riverted or forged into spikes using rolled MS section confirming to Fe 310-0, complete all as specified and directed.

Steel ventilator with top hung shutter including hinges, steel peg stay, complete all as specified and directed.

Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded, complete all as specified and directed.

All as per Srl item No 74 here in before, but without glazing bars, complete all as specified and directed.

Preparing new steel and iron surfaces of any description, over 10cm in width or girth, not otherwise described, and applying two coats of synthetic enamel paint over a coat of red oxide zink primer, complete all as specified and directed.

Sheet glass, of 4mm thick ordinary quality and glazing with oil putty in square n.exc 0.5 Sqm in each pane, complete all as specified and directed.

Sheet glass, of 4mm thick ordinary quality, ground or obscured or frosted, on one side in square n.exc 0.5 Sqm in each pane, complete all as specified and directed.

Resecuring or easing and adjusting without taking down door/window shutter of any description exc 1 sqm but not exc 2 sqm, complete all as specified and directed

Taking down door / window shutter of any description exc 1 sqm and not exc 2 sqm resecurring or easing and adjusting and refixing in same opening, complete all as specified and directed

Taking down existing manually operated steel rolling shuttesr area n.exc 10 Sqm each and erecting in same position, including easening, applying of greasing in rolling shutters channel, complete all as specified and directed.

Steel rolling shutter springs suitable for manually operated steel rolling shutters, fixed as in repairs, complete all as specified and directed.

50mm dia MS pipe shaft for steel rolling shutters suitably drilled and fixed in position for rolling shutters, fixed as in repairs, complete all as specified and directed.

Excavating in trenches, n exc 1.5m wide and n exc 1.5m in depth, for foudation etc, or for shafts, wells cesspits, manholes, pier holes etc n exc 10 sqm on plan and n exc 1.5m in depth and getting out in soft/loose soil, complete all as specified and directed.

Returning filling in including spreading, levelling, watering and well ramming in layers n.exc 25 cm thick in soft / loose soil, complete all as specified and directed.

Removing excavated material exe 250m but n.exe 500m and upto total distance of 1.5 km depositing where directed, complete all as specified and directed.

Cement concrete type D-2, 1:4:8, using 40mm graded aggregate as in foundations, fillings and mass concrete, complete all as specified and directed.

MS TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including MS wire annealed not less than 0.9 mm dia or securing with clips, complete all as specified and directed

All as per Srl item No 88 here in before but 5mm dia over upto incl 10 mm dia as in as in stirups, spacers and binders, complete all as specified and directed.

Form work to sides of concrete foundations footings bases of columns and raft beams, sides and soffits of foundation and plinth beams and similar work vertical or to batter, complete all as specified and directed.

Reinforced cement concrete type B1-1:2:4 (20mm graded aggregate) as in foundation, including rafts, footings, foundation beams, plinth beams, bases for columns etc, complete all as specified and directed.

Formwork to sides of pillars, posts, struts, piers, columns and stanchions rough finished surfaces of concrete, complete all as specified and directed.

Reinforced cement concrete type B1-1:2:4 (20mm graded aggregate) as in columns, pillars, piers, posts and struts, complete all as specified and directed.

20mm thick Granite (of any type) work (table rubbed and polished) for wall lining (veneering to wall) 12mm thick in cement mortar (1:3) and pointing with white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, complete all as specified and directed.

Rendering 10mm thick in CM 1:4 on fair faces of brick work or concrete surfaces as in backing coat to receive wall tiles etc., complete all as specified and directed.

Screed bed or bedding layer of mortar 15mm thick for laying floor tiles (CM 1:4), complete all as specified and as directed.

Glazed coloured ceramic tiles in vertical surface 350x 250x 7 mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match, complete all as specified and directed.

Granite (of any type) tiles 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete over 15mm thick screed bed CM 1:6 including dismentaling of old Granite tile any type, complete as specified and directed

Non skid Ceramic tiles coloured 7 to 8mm thick (square/ rectangular) polished, area of each tiles exceeding 0.18 Sqm but not exceeding 0.38 sqm each, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, complete as specified and directed

Soap dish holder, fixed as in repairs, complete all as specified and directed. Make-Jaguar Code No- ACN-CHR-1131N or equailent.

Brass chromium plated Tubular towel rail, 20mm dia, D type, 60cm long, fixed as in repairs, complete all as specified and directed. between flanges complete all as specified & directed.

Towel ring square with round flange, fixed as in repairs, complete all as specified and directed. Make-Jaguar Code No-ACN-CHR-1121N or equivalent

Glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm with chromium plated bracket guard and railing 60cm longSheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing of 600 mm long with cp bracket, fixed as in repairs, complete all as specified and directed.

Glass corner shelf with CP bracket, fixed as in repairs, complete all as specified and directed. Make-Jaguar ACN-CHR-1173N or equivalent

15mm bore pillar taps, fancy type, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe, fixed as in repairs, complete all as specified and directed.

Brass chromium plated bottle traps for wash basins with inlet and outlet, fixed as in repairs, complete all as specified and directed. screwed for pipe or connections including necessary packing, union and cap and fixed all as specified and directed.

Hyegenic health fauset including 1.0 mtr long CP flexible tube with hook, fixed as in repairs, complete all as specified and directed. Make Jaquar Cat part No-ALD 573 or equailent.

One piece wash down water close with hydraulic sheet cover and connecting to 'P' or 'S' rimless, fixed as in repairs, complete all as specified and directed. Make; Somani Cat part Maxico white with ezee close seat cover or equailent.

Vitreous China squatting pan, ‘Orissa' pattern, size 580 x 440 mm white, with integral foot rest(excluding flushing cistern and flush pipe) including provision of lime concrete bedding, fixed as in repairs, complete all as specified and directed.

10 litres capacity, PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets, fixed as in repairs, complete all as specified and directed.

Clove counter top basin of size515x380x120mm of whitecolour complete, fixed as in repairs, complete all as specified and directed.

Glazed finished urinal with sensor of size 370x390x610mm, fixed as in repairs, complete all as specified and directed. Make-Hindware Cat No-60018,

8 mm th curved shape urinal partition with frosted glass chrome finish of size-900mmx450mm, fixed as in repairs, complete all as specified and directed. Make-Jaguar Code No- JSE-CHR-110UC450X or equailent.

Two way bib tap with wall flange standard of brass any colour screwed for iron pipe 15 mm bore, fixed as in repairs, complete all as specified and directed. Make- Jaguar Cat no-FLR-5041N.

15 mm bore Bib taps, fancy type, chromium plated, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule, fixed as in repairs, complete all as specified and directed.

CP connection, 15 mm size with CP nuts of length 450mm, fixed as in repairs, complete all as specified and directed.

Toilet roll holder with flap, fixed as in repairs, complete all as specified and directed. Make-Jaguar Code No- ACN-CHR-1153S or equailent.

CP Gratings size 125 mm dia, fixed as in repairs, complete all as specified and directed.

Taking up or down 15mm bore water tubing and connection cleaning for refixing or removing to store, complete all as specified and as directed.

Taking up or down 20 mm bore water tubing and connection cleaning for refixing or removing to store, complete all as specified and directed.

Cutting chases in stone masonry walls, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10cm girth etc., complete all as specified and directed

15 mm dia GI pipe medium grade with all fittings and fixed to wall /laid in floor, complete all as specified and directed.

All as per Srl item No 123 here in before but 20 mm dia GI pipe, complete all as specified and directed.

15 mm bore, stop valves, concealed type cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed but fancy type, chromium plated with long shank and cup (concealed type) including flench, complete all as specified & directed.

Stop angal cock 15 mm dia chromium plated, screwed down, high pressure, screwed both ends for 15mm bore iron pipes or for unions, fixed as in repairs, complete all as specified and as directed. Make-Jaguar or equivalent.

110 mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors or fixed with wall including necessary fixing cleats/ clamps, fixed in repairs, complete all as specified and directed.

75 mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors or fixed with wall including necessary fixing cleats/ clamps, fixed as in repairs, complete all as specified and directed.

PVC bends of 110 mm dia, fixed as in repairs, complete all as specified and directed.

PVC bends of 75 mm dia, fixed as in repairs, complete all as specified and directed.

PVC branch piece (Y junction) single socketed of 110 mm dia, fixed as in repairs, complete all as specified and directed.

PVC branch piece (Y junction) single socketed 75 mm dia, fixed as in repair, complete all as specified and directed.

Cutting opening through brick wall/stone wall masonary for door,windowand other opening incl trimming surface to receive rendering etc., complete all as specified and directed.

Taking down chowkhat with shutters (without taking off shutters from the frames )of any description n.exc.1.0 sqm each removing to or from store, complete all as specified and directed.

Designer UPVC door including frame work as colour approved by GE, fixed as in repairs, complete all as specified and directed.

Demolition cement concrete in ground floor and paving not exceeding 15 cm thickness (below or above ground level) un-reinforced, complete all as specified and directed.

Cement concrete type D-2, 1:4:8, using 40mm graded aggregate as in foundations, fillings and mass concrete, complete all as specified and directed.

Pre-cast cement concrete block type C1 1:3:6 (20mm graded stone aggregate) masonry with solid blocks, exc. 10cm in width and setting in mortar 1:6, complete all as specified and directed.

Taking down cement or cement lime plaster, any description on brick or stone walls, etc. Including racking out joints, hacking for key, scrubbing down with water, etc. all as specified. Note: All debris and rubbish shall be removed from MOD land during or at the end of each working period at his risk and cost in accordance with all applicable federal, state, and local regulations.

Rendering 15 mm thick in cm 1:4 of brick work or concrete surfaces finished even and smooth without using extra cement, complete all as specified and directed.

Applying 3mm thick JK/Birla white putty on wall and prepare the surfaces to achieve flawless smoothness, complete all as specified and directed.

Preparation of putty finished new plastered/old surfaces of wall and applying two coats of distempering walls with distemper oil-emulsion white or tinted over a coat of Chalk whiting, on plastered surfaces, preparatory to distempering, complete all as specified and directed.

Washing, rubbing down and stopping of distempered and painted surfaces and applying two coat of Distempering walls with distemper oil-emulsion white or tinted including complete removal of existing treatment , complete all as specified and directed.

Washing, rubbing down and stopping of distempered and painted surfaces and applying two coat of Distempering on ceilling with distemper oil-emulsion white or tinted including complete removal of existing treatment, complete all as specified and directed.

Pre-cast cement concrete solid block masonry, exceeding 10cm in width, blocks cast in PCC 1:3:6, type C1, using 20mm graded stone aggregates, set in cement mortar 1:6, complete all as specified and directed.

Two coats of Distempering wall with distemper oil emulsion white or tinted over a coat of 1mm thick wall care putty, including preparation of new surface, complete all as specified and directed.

Washing, rubbing down and stopping of distempered and painted surfaces and applying two coat of Distempering walls with distemper oil-emulsion white or tinted including complete removal of existing treatment, complete all as specified and directed.

Washing, rubbing down and stopping of distempered and painted surfaces and applying two coat of Distempering on ceilling with distemper oil-emulsion white or tinted including complete removal of existing, complete treatment all as specified and directed.

Dismantling boarding, any description(wall pannelling/ ceilling/ linning/ cladding/ partition etc.) fixed in any position with nails/screw complete all as directed.

Site of the TRAY PANEL SCREW type system with aluminium composite panel of approved plain colour or wood grain printed on interior walls, columns, MS structure, ceiling, coping, slab projectons at all heights and elevation including necessary aluminium framework. The aluminium composite panel should 4 mm thick consist of 3mm thick thermoplastic core of anti toxidant LDPE sandwitched between 2 skins of 0.5mm thick aluminium alloy sheet making a total panel thickness of 4mm. The external surface shall be finshed with PVDF based coating on the top side and service coating on the reverse side shall be with a polymer paint, complete all as specified and directed. NOTE:- The system shall be fitted with necessary Aluminium. sub frames, cleats and shall be fixed to the masonry/ RC walls/ MS structure with necessary clamps, galvanized M.S brackets and anchor fasteners. All clamps and brackets shall be Hot dip galvanized minimum 80 microns thick and shall conform to IS: 4759-1996. Any other acessories such as fastening straps, nuts, bolts, rivets, washers, etc. other than anchor system shall be in Indian standard grade. all joints of ACP must be sealed with approved sealent of approved colour. sealant make DOW CORNING 789 weather sealant. Rate shall include to provide open cell polyethylene backer rods, weather sealant etc, all materials and labour complete.

Providing and fixing in position suspended false ceiling made out of 10mm (apprx.) thick Gypsum Plaster Boards of Indian Gypsum or equivalent made G.I standard section framework in the pattern as per manufacturer's instruction. The G.I. Section frame work shall be tied to the roof and walls with the anchor fastener screws/bolts of appropriate size recommended by the manufacturer. The boards shall be fixed to the frame work with the screws and the joints shall be flushed and finished with requisite jointing compounds paper tapes etc. Rates includes execution of works in different levels/offsets etc. The surface shall be finished evenly by applying putty, sand papering, applying primer and two coats of plastic emulsion paint evenly including necessary additional ceiling sections and intermediate channels and openings for light fixtures, A.C. ducts, vertical drops, offsets etc., complete all as specified and directed.

Vanition blinds antique finish wood blinds coated with PU glass coat matt clear to retain the texure of antique finish for years 50mm wood slates including all necessary fittings complete for the windows at all heights, all materials and labour etc. with complete accessories in all respects as per directions of Engineer-in-Charge, complete all as specified and directed.

Taking down carefully copper/aluminium point wiring (light fan socket or power) complete including fittings such as switches, ceiling rose, pendants, regulators, sockets complete as directed and removing retrieved materials and making good the disturbed surface, complete all as specified and directed

Taking down existing light fittings of any description from wall/ ceiling including keeping in safe custody by making good the disturbed surfaces of walls, complete all as specified and directed.

Taking down ceiling fan/wall mounted fan/Air circulators, sealing cable end, dismantaling blades, and removing fan including painting and refix the same including connecting up and provision of cable from ceiling rose or connector to fan, complete all as specified and directed.

Consealed type Point wiring complete with 1100volts grade, single core, PVC insulated FRLS cable multi-stranded copper conductor of size 1.5 sqmm nominal area, drawn through and including rigid, PVC conduit of suitable size, with all necessary fittings and accessories fixed in the walls/ ceiling with one run neutral and one run of single core cable of same description above but green colour in continous earthing wire connected to common earth dolly including PVC junction / mounting boxes on / in the wall / ceiling for piano switches/ switch socket combination/ fan regulators etc and GI junction box duly covered with 3mm thick hylam sheet for One light/ fan point controlled by one single pole 5 Amps switch, complete all as specified and directed.

All as per Srl item No 158 here in before but for one switch socket out let point 5 Amps on independent board, complete all as specified and directed.

All as per Srl item No 158 here in before but for one switch socket out let point 5 Amps on same board with other switches, complete all as specified and directed.

All as per Srl item No 158 here in before but for PVC insulated FRLS copper conductor of size 2.5 sqmm for switch socket multipurpose 15 Amps including provision of 2.5 Sq mm PVC insulated FRLS copper conductor cable as earth continuity conductor on independent board, complete all as specified and directed.

All as per Srl item No 158 here in before but for PVC insulated FRLS copper conductor of size 4.0 sqmm for switch socket multipurpose 15 Amps including provision of 4.0 Sq mm PVC insulated FRLS copper conductor cable as earth continuity conductor on independent board, complete all as specified and directed.

Modularswitch , 1 Module single pole one way 10 Amps, complete all as specified and directed.

Modularswitch , 1 Module single pole one way 16 Amps, complete all as specified and directed.

Modular socket , 2 Module 6 Amps 240 volts Ac 2/3 pin combined suitable for inserting 2 pin 5 Amps/ 3 pin 5 Amps plug top all as specified and directed at site, complete all as specified and directed.

Modular socket , 2 Module 6/16 Amps 240 volts Ac 6 pin combined suitable for inserting 3 pin 6/16 Amps plug top all as specified and directed at site, complete all as specified and directed.

Switch socket combination outlet 6 pin 5&15 amps multi purpose flush type universal pattern 230 v, complete all as specified and directed.

Stepped type electronic fan regulator flush type, complete all as specified and directed.

PVC ceiling rose 65 x 50 mm surface type with 3 terminals, complete all as specified and directed.

LED batten luminaire surface mounted, 4 feet system wattage of 18 Watts , 2500 Lumens, efficiency > 110, CCT 6500k , CRI > 80 , Wall / surface mounted , IP 20 aluminium etrusion housing complete with including connecting up with PVC sheathed 1.0 sqmm 3 core copper conductor flexible wire from ceiling rose to fitting, complete all as specified and directed. (Make- Bajaj cat no 112867 BCLSB 18WH or equivalent specifications model of make- Philips/OSRAM/Wipro/GE

Batten luminaire surface mounted 2 feet system wattage of 10 Watts with lifetime of 50000 burning hours with 70% of its initial lumen maintained, complete all as specified and directed. (Make- Bajaj cat no 11247 BCLSB 10WH or equivalent specifications model of make- Philips/OSRAM/Wipro/GE

Industrial box type Recessed luminaires (28W range) with efficient optics ensuring perfectly uniform illumination, optimised and unparalleled light distribution.with efficient optics ensuring perfectly uniform illumination, optimised and unparalleled light distribution incl connecting up with PVC sheathed 1.5 sqmm 3 core copper conductor flexible wire from ceiling rose to fitting fixed, complete all as specified and directed. Make-Bajaj Cat :BRTX 2-28W LED 8F WH White or equivalent make in Philips/Wipro

20W High efficient LED Security light fitting with pressure die cast Aluminum housing, IP66, Lumen output 100 lu/w system efficiency 100, colout temp 5700 k ,CRI 70 , including provision of 40MM dia GI light grade pipe1.5 meter length bend to shape and necessary clamps etc for fixing the light fittings on wall fixed, complete as specified and directed. Make-Bajaj Cat :BCLST 20W LED I V2 WH White or equivalent make in Philips/Wipro

15W recess mounted high performance low-height LED downlighter suited for requirements non-integral flexible , die-cast Al. LED fixture with ivory powder coating for updown accent lighting. Range 220 V - 240 V, 50Hz complete with incl connecting up with PVC sheathed 1.5 sqmm 3 core copper conductor flexible wire, complete all as specified and directed. Make Phillips cat part No DN296B LED 15S-6500 PSUWH.

12W LED track light fitting Track mounted accent lighting luminaire with compact housing and slim gear box with Color rendering Index of 90. `Spot light luminiare suitable for 1 phase track with powder coated alluminium body, 240V 50Hz, complete all as specified and directed. Make : Philips Cat No ST391T LED10/930 PSU-E NB 1C WH IN

Post top lanterns (HERITAGE) 45W worm white LED made in cast aluminium spigot housing with decorative opal acrylic diffuser and IP65 protection complete including provn of pipe for fixing of fitting, complete all as specified and directed.

Exhaust fans of size 250mm sweep, AC single phase 230/ 240 V of non- metallic body with louver and other accessories, complete all as specified and directed Make : Havell's,Bajaj Bahar

Sheet metal enclosure MCCB DB VTPN 125Amps 4 way vertical ,double door type ,IP 43 protection, isolated neutral bar, insulated busbar assembly, mechanical impact strength IK 08 i, complete all as specified and directed.

Sheet metal enclosure for DB's double door 8 ways when MCBs to be used Triple pole and neutral,deep drawn with 200 Amps rated copper bus bar 430V, complete all as specified and directed.

Sheet metal enclosure for DB's double door 08 ways when MCBs to be used single pole and neutral,deep drawn with 200 Amps rated copper bus bar 240V, complete all as specified and directed.

Sheet metal enclosure for DB's double door 04 ways when MCBs to be used single pole and neutral,deep drawn with 200 Amps rated copper bus bar 240V, complete all as specified and directed.

MCB TPN, 63 Amps, 415 V, C- series with breaking capacity of 10KA, complete all as specified and directed.

MCB TPN, 32 Amps, 415 V, C- series with breaking capacity of 10KA, complete all as specified and directed.

MCB SPN, 40 Amps, 240/415 V, B- series with breaking capacity of 10KA, complete all as specified and directed.

15 watt recess mounted high performance low-height LED downlighter suited forequirement non-integral flexible, die-cast AI. LED fixture with ivory powder coating for updown accent lighting Range 220 V-240 V, 50 Hz with including connecting up with PVC sheathed 1.5 Sq mm 3 core copper conductor flexible wire, complete all as specified and directed. Make : Philips cat part No DN296B LED 15S-6500 PSUWH

12 watt LED track light fitting Track mounted accent lighting luminaire with compact housing and slim gear box with Color rendering Index of 90 'Spot light' luminiare suitable for 1 phase track with powder coated aluminium body, 240 V 50Hz, complete all as specified and directed.

Exhaust fan of size 250 mm sweep, AC single phase 230/240 V of non metallic body with louver and other accessories, complete all as specified and directed.

Sub main wiring with Two single core PVC insulated cable with copper conductor multistranded 1100 volts grade 04 sqmm in and including non-metallic rigid PVC conduits and accessories and fixing arrangements fixed to surface on wall, floor or ceiling etc including 2.5 sqmm PVC insulated unsheathed copper earth continuity conductor, fixed as in repairs, complete all as specified and directed. Note : One run of earth continuity conductor,one run of PVC conduit and two run of copper conductor together taken as one length for measuring unit length.

MCB SP, 6-40 Amps, 240V, B- series with breaking capacity of 10KA, complete all as specified and directed.

Sub main wiring with Two single core PVC insulated cable with copper conductor multistranded 1100 volts grade 10 sqmm in and including non-metallic rigid PVC conduits and accessories and fixing arrangements fixed to surface on wall, floor or ceiling etc including 10 sqmm PVC insulated unsheathed copper earth continuity conductor. Note : One run of earth continuity conductor,one run of PVC conduit and two run of copper conductor together taken as one length for measuring unit length, fixed as in repairs, complete all as specified and directed.

Sub main wiring with Two single core PVC insulated cable with copper conductor multistranded 1100 volts grade 06sqmm in and including non-metallic rigid PVC conduits and accessories and fixing arrangements fixed to surface on wall, floor or ceiling etc including 6 sqmm PVC insulated unsheathed copper earth continuity conductor, fixed as in repairs, complete all as specified and directed. Note : One run of earth continuity conductor,one run of PVC conduit and two run of copper conductor together taken as one length for measuring unit length.

Sub main wiring with \Four single core PVC insulated cable with copper conductor multistranded 1100 volts grade10 sqmm in and including non-metallic rigid PVC conduits and accessories and fixing arrangements fixed to surface on wall, floor or ceiling etc including Two single core 10 sqmm PVC insulated unsheathed copper earth continuity conductor, fixed as in repairs, complete all as specified and directed. Note : One run of earth continuity conductor,one run of PVC conduit and two run of copper conductor together taken as one length for measuring unit length.

Earthing complete with galvanised steel earth plate electrode 60x60cmx6mm thick, buried directly in ground ( earth pit not less than 2.25mtrs deep below ground level) with top edge of the plate not less than 1.5mtrs below normal ground level, including provision of galvanised iron earth strip 32x6mm as earth lead connected by means of bolts, nuts, check nuts and washers of galvanised iron, provision of 40mm dia GI pipe medium grade for watering arrangement and PCC 1:3:6 type C1 chamber, MS Funnel, wire gauge, 50mm thick RCC 1:2:4 type B1 for earth pit cover with 6Nos x 8mm dia high strength deformed steel TMT bars on both ways, including necessary excavation in any type of soil, returning, filling in, removal of surplus soil to a distance not exceeding 50m, provision of charcoal and salt in alternate complete all as shown in electrical place No 3 of schedule part I 2009 all as specified and as directed and testing on completion, complete all as specified and directed. Note : Cost of GI earth lead and GI protection pipe up to 7.5m length shall be deemed to be included in the rate quoted for this item.

chowdeshwariconstructionco

Moulya Builders

Raashi Constructions

SRI GANESH ENTERPRISES