Special repair to bldg No. ET-207 (or guest room) and special repair/ replacement of old LT pannel at sub station No.10 and provision of water cooler, Deep freezer and refrigerator at CME, Pune

Amount

Dismantling of single layer Mangalore Pattern roof tile laid dry complete all as specified and directed

All as per item No. 1 above, but bedded in lime or cement mortar complete all as specified and directed.

Dismantling battens for tiles, shingles etc, of any size including tilting fillets spacing exc. 15 cm complete all as specified and directed.

Dismantling timber scantlings 40 sq. cm and over in section, in any position complete all as specified and directed.

Dismantling boarding, any description, fixed in any position with nails complete all as specified and directed.

S&F rolled sections as in main and cross beams, hips and jack rafters, purlins where connected to common rafters and running rails and guides for sliding doors, fixed with angle cleats or other connecting plates etc Fe-410-W (Gde E-250) Quality A complete all as specified and directed.

S & F 6 mm thick MS plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment etc. conform to Fe-410-W (Gde-E-250) quality A complete all as specified and directed.

M & L for preparation of new or previously untreated surfaces of iron of any description over 10 cm in width or girth and applying two coats of synthetic enamel paint over and including a coat of red oxide zinc chrome primer complete all as specified and directed

S & F pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws etc. complete all as specified and directed.

S & F pre-painted galvalume aluminium zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as in ridges, hips, valley, gutters etc. complete all as specified and directed.

S&F steel work in tubular trusses including special shaped washer etc., purlins, rafters, complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St.-240 complete all as specified and directed.

S & F Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing confirming to Fe 410-W Gde-E-250 quality A etc. complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for etc. complete all as specified and directed.

S & F for 1 mm thick mild steel, plain, black sheet in wall cladding, steel gates and similar work, cut to size, holes punched including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. complete all as specified and directed.

Taking down chowkats or frames with shutter (without taking off shutters from the frames) exc. 1.5 but not exc. 4.00 sqm each and removing from site complete all as specified and directed.

Taking down chowkats or frames with shutter(without taking off shutters from the frames) not exc. 1.50 sqm each and removing from site complete all as sepcified and directed.

S & F anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing including powder Coating (minimum thickness of powder coating 50 micron) etc. complete all as specified and directed.

S & F anodised aluminium window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws including powder coating ( minimum thickness of coating 50 micron ) etc. complete all as specified and directed.

S & F 5.5 mm thick sheet glass, ordinary quality and glazing with oil putty in square exc 0.5 sq. m in each pane etc. complete all as specified and directed.

S & F 5 mm thick figured glass, pin head type and glazing with oil putty in squares n exc 0.5 sq. m in each pane etc. complete all as specified and directed.

S & F galvanised mild steel wire cloth, 0.63mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks, or galvanised wire staples etc. complete all as specified and directed.

M&L framed work such as grills or grating etc with ends of bars shouldered as framed guard bars conforming to Fe-290 Gde E-165 all as specified and directed.

S & F solid PVC door frame of size 50mm x 47mm made out of 5 mm plain colour PVC sheet reinforced with M.S. square tube etc all as specified and as directed.

S & F factory made solid PVC moulded door shutter, 30 mm thick 2mm thick 3D wood grain Moulded PVC sheet polyurethane painted on the front face & 2mm plain colour PVC sheet on back face complete all as specified and as directed.

S& fixed factory made plain framed panelled shutters 35mm thick of 2nd class hard wood (any number of panels) with panels of timber flat on both sides feather edges or panel of 9mm BWP commercial ply or 12mm thick veneered particle board with commercial face veneers fixed to chowkhat . The size of rail and stile as per IS : 1003 (Part-1), kiln seasoned and chemically pressure treated complete all as specified and as directed.

S& fixed 2nd class hard wood 35 mm thick glazed and skeleton shutters open rebated and prepared to receive glass, gauze,etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass,etc, size of members of shutters as spfd in SSR Part-1, Section 8, clause 8.24 (a) complete all as specified and directed.

S&F 2nd class hard wood plain, solid, straight chowkhats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints etc. complete all as specified and directed.

S & F Mild Steel works as in bands straps, hold fasts etc, conforming to Fe-290 Gde E-165, embedded portion duly painted with bituminous paint and sanded, complete all as specified and directed.

M & L Cement concrete type B1 (1:2:4) using 20mm graded stone aggregate as in copings, bed plates, fixing of hold fasts and other similar works and the like incl weathering, slightly rounded or chamfered angles and throating as directed incl use and waste of necessary form work complete all as specified and directed.

S&F 150mm hasp and staple, mild steel, wire type stove enamelled black, including bolt to hinge plate and fixed with screw complete all as specified and directed.

S & F Mild steel butt hinges medium weight , cold rolled, 100mm, ISI marked, complete all as specified and directed.

M&L 200 mm aluminium anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed.

M&L 150 mm aluminium anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed.

S&F 125mm long aluminium anodised handles or extruded section complete all as specified and directed.

S&F 150 mm long aluminium anodised handles or extruded section complete all as specified and directed.

S&F 300mm long aluminium alloy, anodised, sliding door bolt with hasp, staple, (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts of extruded sections or cast-aluminium alloy complete all as specified and directed.

S&F Mild steel 300mm ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed.

S&F galvanised mild steel wire cloth 0.56mm nominal dia of wire and width of aperture 1.18mm & fixed with tinned tacks or galvanised wire staples complete all as specified and directed.

S & F in repair galvanised mild steel wire cloth, 0.63mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks, or galvanised wire staples etc. complete all as specified and directed.

S&F 100 mm butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21 complete all as specified and directed.

Taking up or down 15mm bore steel water tubing & connections, including cleaning for refixing or offering credit as per schedule of credit all as directed.

All as per item No. 41 above, herein before but 20mm bore

S&F 15mm bore medium grade galvanised steel water tubing with all fitting & fixed complete to walls or ceiling or laid in floors complete all as specified and directed.

Refixing 15mm bore old steel water tubing & connection in new or old position of wall, ceiling, floor etc all as specified and directed. Note :- The serviceable tubing obtained from sl item No.41 shall be re-used in this item.

S&F 20mm bore medium grade galvanised steel water tubing with all fitting & fixed complete to walls or ceiling or laid in floors all as specified and directed.

Refixing 20 mm bore old steel water tubing & connection in new or old position of wall, ceiling, floor etc all as specified and directed. Note :- The serviceable tubing obtained from sl item No.42 shall be re-used in this item.

M& L For Cutting chases, pinning in stone concrete black or slab , making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc; and cutting chases for concealed water tubing or concealed conduit wiring, etc. and making good, cutting exceeding 20cm girth etc. complete all as specified and directed.

S&F in repair vitreous china wash basin, white, flat back, size 630x450mm excluding taps, waste chain and plug and porcelain stopper but including brackets, waste coupling complete all as specified and directed.

S&FVitreous China wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) including seat cover complete all as specified and directed

S&F in repair 10 litre capacity PVC valveless, syphonic action type flushing cistern, low level, white, with inlet ball valve, float and handle including bracket and 32mm dia flush pipe of polyethylene of low or high density for low level cistern complete all as specified and directed.

S&F in repair brass chromimum plated two way bib cock fancy type, 15mm bore ( min Wt. 550 grams) of approved make by EIC/ GE etc.complete all as specified and directed.

S & F brass chromium plated, 15 mm bore health faucet, ( flexy type) 1.00 mtr. long of approved make by EIC/GE etc. complete all as specified and directed.

S&F in repair 15 mm dia pillar taps, cast copper alloy, with capstan heads, chromium plated fancy type , screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long shanks and flynuts, screwed for iron pipe complete all as specified and directed.

S&F in repair PVC connection 15mm size with PTMT nuts of length 450mm complete all as specified and directed.

S&F in repair 15mm fancy type bib tap, chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed

S&F in repair 15mm dia stop valve chromium plated fancy type screwed down high pressure with crutch or butterfly handle screwed both end for iron pipe or for union complete all as specified and directed.

S & F in repair overhead shower 100 mm dia round shape single flow (ABS Body Chrome plated with grey face plate ) with Rubit cleaning system complete fixed to ceiling all as specified and directed by Engineer-in Charge. Make: - Jaquar Cat No. OHS-1989 or equivalent approved make indicated in list of makes in tender as approved by GE.

S&F in repair 75mm PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed.

S&F in repair 75 mm PVC (SWR) bend any radius complete all as specified and directed

S&F in repair 75mm PVC (SWR) junction single (single T) equal or unequal complete all as specified and directed.

M&L in repair 75mm PVC (SWR) floor trap with grating including jointing with solvent cement complete all as specified and directed.

S&F in repair 75mm PVC (SWR) vent cowl complete all as specified and directed.

S&F in repair 110 mm PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed.

S&F in repair 110 mm PVC (SWR) bend any radius complete all as specified and directed

S&F in repair 110 mm PVC (SWR) junction single (single T) equal or unequal complete all as specified and directed.

M&L in repair 110 mm PVC (SWR) floor trap with grating including jointing with solvent cement complete all as specified and directed.

S&F in repair 110mm PVC (SWR) vent cowl complete all as specified and directed.

S&F in repair stainless steel sink, made out of 1.00 mm thick sheet for kitchen with plug, washer pipe cast iron cantilever brackets, connecting union overall size 495x420mm bowl size 410mm x 330mm x160mm all as specified and directed.

S&F in repair Brass chromium plated tubular towel rail, 20mm dia, D type 60cm long between flanges complete all as specified and directed.

S&F in repair sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with stainless steel bracket guard and railing 60 cm long etc. complete all as specified and directed.

S& F in repair stainless steel Soap dish holder complete fixed to wall as specified and directed by Engr-in-Charge. Make :- Cera code No. 50061606 or equivalent of Jaquar/ Seico Industries/ Zoloto

S&F in repair stainless steel toilet paper roll holder with flap complete all as specified and directed. Make :- Cera code No. 5006110 or equivalent of Jaquar/ Seico Industries/ Zoloto.

S& F in repair Brass CP mixer for mixing hot & cold water screwed down for15 mm size iron pipe and fixed complete all as specified and directed.

S&F in repairs 19/20mm dia MS pipe powder coated of approved colour as in decorative type curtain rods all as specified and directed.

S&F in repairs brackets powder coated of approved decorative type suitable for fixing curtain rods of 19/20mm dia pipe incl fixing screws, drilling etc as per sample approved complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles and rubbish off the premises complete all as specified and directed.

Demolition of cement concrete (unreinforced ) in ground floors and pavings not exceedidng 15cm thickness (below or above ground level) all as specified and directed.

M&L for 75mm thick PCC type D-2 (1:4:8) using 40mm graded stone aggregate as in sub base etc complete all as specified and directed

M&L for screed bed or bedding layer of mortar 15 mm thick for laying floor finishes in CM 1:6. all as specified and directed.

M & L Non-skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, over screed bed or bedding layer etc. complete all as specified and directed.

M & L Non-skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match etc. complete all as specified and directed.

All as per item No. 81 above, but as in skirting

M& L rendering 10mm thick cement mortar in 1:4 as in backing coat for fixing wall tiles complete all as specified and directed

M&L for glazed ceramic coloured tiles in vertical surface 350mmx250mmx7mm /450mmx350mmx7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick, in cm 1:3 backing coat etc. complete all as specified and directed by Engr-in-charge

Dismantling stone slab and tiles of any description and thickness as in floor including cement mortar bedding and removing complete all as specified and directed.

M&L machine cut cuddappah stone slab 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing over and including 15mm thick screed bed in CM 1:6 complete all as specified and directed.

M& L 20 mm thick, Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite etc complete all as specified and directed.

Rounding to edges of stone slabs, such as in steps, cooking platform and other similar situation complete all as specified and directed.

Taking down cement plaster on brick or stone walls or concrete surface etc including raking out joints, hacking for key scrubbing down with water all as specified and directed.

M&L rendering 15mm thick on stone masonry surfaces in CM 1:6 finished even and smooth with sagol over and including dubbing out average 10mm thick on irregular face of walls in CM 1:6 complete all as specified and directed.

M&L rendering 15mm thick on stone masonry surfaces in CM 1:4 finished even andfair and including dubbing out average 10mm thick on irregular face of walls in CM 1:6 complete all as specified and directed.

M&L preparing newly plastered surfaces of wall and applying two coats of oil bound distemper over one coat of primer on walls complete all as specified and directed.

M&L Preparation of newly plastered or unplastered surfaces wall and applying two coats of cement base paint complete all as specified and directed.

Demolition of brick or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars etc but excluding ashlar facings, dressed stone work and precast concrete articles complete all as specified and directed.

M&L precast solid block masonry of block in precast cement concrete 1:3:6 type C-1 using 20mm graded stone aggregate as in wall exceeding 10 cm in width and built in cement mortar 1:6 complete all as specified and directed.

M&L complete removal of existing treatment and applying 3mm thick wall care putty and applying two coats of Oil bound distermper white or tinned over one coat of primer on walls, all as specified and directed.

All as per item No.97 above, but two coat of cement base paint without wall care putty complete all as specified and directed.

M & L for false ceiling with 4mm thick designer 'E' board fixed on GI grid work with powder coated finish on exposed surface of size 0.6 x 0.6m consisting of GI angle supported on wall of size 24mm x 28 x 0.7mm, main tee of size 24mm x38mm x 0.7mm, cross tee of size 24mm x 28mm x 0.7 mm using purpose made members interlocking to each other and 40mm x 3mm flat GI mild steel strip suspender made to shape at 1200mm c/c fixed with 3mm dia GI wire and making holes etc all as directed including two coats of white wash on ceiling after preparation of surfaces and as per manufacture instruction including taking down old ceiling Make of GI Grid work : Armstrong/Swastik/Techno Grid Make of 'E' board : Everest/Indian Gypsum/Armstrong or equivalent approved .

M & L for 75mm thick cement concrete 1:3:6, type C2 using 40mm graded stone aggregate as in floors, plinth protection, path etc. and finished the surface even and smooth without using extra cement all as specified and directed.

Taking down carefully aluminium point wiring (light, fan,bell, socket or power) complete (fitting such as switches, ceiling rose, pendent, regulators etc.) removing material to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately and making good disturbed surfaces of walls, floors to match with existing surface etc.

M&L for point wiring for with FRLSH cable 1.5 sqmm PVC insulated (red for phase and black for neutral) unsheathed, multi stranded copper conductor 1100 volt grade in and incl not less than 2mm thick PVC casing/caping with all accessories and 1.5 sqmm green in colour PVC copper conductor cable for earth continuity connected to common earth dolly incl PVC box surface/flush type with PVC sheet for mounting fittings such as switches, sockets, fan regulators etc complete all as specified and directed and making good to disturbed surface of wall etc. for the following:-

One light point controlled by one switch

One fan/exhaust fan point controlled by one switch and regulator

Socket outlet, three pin 5 Amps on the same board

Socket outlet, three pin, 5 Amp, independent

All as per item No.102 above, but with stranded copper conductor 2.5 sq.mm (nominal area), including PVC insulated stranded copper conductor 2.5 sqmm (nominal area) single core as earth continuity conductor to common earth and connecting to earth dolly complete all as specified and directed.

S & F Ceiling rose, surface Bakelite suitable for 3 pin, 230 Volt, 50 Hz AC supply complete all as specified and directed.

S & F Switch piano, flush type, single pole, one way and 6 Amp, 230 Volt complete all as specified and directed.

S & F Switch piano, flush type, single pole, one way and 15 Amp, 230 Volt complete all as specified and directed.

S & F Socket outlet multipurpose having provision for 3 pin, 6 Amps and 2 pin, 6 Amp, piano flush type complete all as specified and directed.

S & F Socket outlet multipurpose having provision for 3 pin, 15 Amps and 3 pin, 5 Amp, piano flush type complete all as specified and directed.

Supply and fixing bell push flush type, 5 Amps, 240 Volts

Supply and fixing bell AC, 230 Volts single pole

S & F decorative ultra slim with polycarbonate housing with high lumen output environment friendly, energy efficient ready to use pack surface and wall mounted LED batten (LED tube light fitting complete 22W) with integrated electronic driver and 02 Nos PVC square blocks incl taking down old unsv fitting.

S&F building security LED light fitting 25 Watt , energy saving and environmental friendly long life LED fitting made up of pressure die cast aluminium housing with acrylic cover as diffuser with IP 66 protection including suitable size bracket incl taking down old UNSV one.

Supply and fix exhaust fan AC single phase 230/240 Volts of size 250mm sweep, 1400 rpm with louvers and all fixing arrangements such as plywood 18mm thick of suitable size all as specified and directed.

Taking down ceiling fan of any size after disconnecting the wire from existing ceiling rose and deposited to MES store (AGE E/M sub division) and supply and fixing ceiling fans complete with blades, down rods, regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and directed.

S&F enclosure, single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20 Amps, 240 Volt incl taking down old unserviceable one.

Supply and fix sheet metal enclosures TPN DB 4 way, 415 Volts double door complete all as specified and directed.

Supply & fix MCB 4 pole 'B' series 100 Amps capacity AC, 415 Volts, 10 kA complete all as specified and directed.

M&L for sub main wiring with approved colour coding as per IS with two single core PVC insulated cable with stranded copper conductor of size 04 sq. mm nominal area and drawing into PVC conduit including PVC insulated 04 Sqmm (nominal area) stranded copper condutor earth wire complete. Note : Two runs of 04 sqmm cable, one run of 04 sqmm earth cable and one run of PVC conduit will be measured as one unit.

Supply & fix DB 6 way SPN with 200 Amps rated bus bar, double door including wooden box suitable size.

Supply and fixing of MCB single pole rated capacity 5 to 32 Amps, 240 Volts breaking capacity 10 KA C series.

Supply and fixing of MCB single pole and neutral rating capacity 40 to 63 Amps, 240 Volts breaking capacity 9 KA C series.

M & L for Earthing complete with galvanized steel plate electrode 60 cm x 60 cm x 6mm surrounded by charcoal and salt, buried directly in ground vertically in a pit of depth not less than 2.25 metre below ground level with top edge of the earth plate at a depth of not less tahn 1.50 metre below ground level connected to galvanized iron or steel earth wire, 4 mm dia (No.8 SWG) by means of bolts, nuts and washers of galvanized iron, earth wire protected by galvanized steel pipe 15mm dia (Light grade) & connected to main switch or main control board all as shown in electrical plate No.3 of SSR-2009 Part-I & including necessary excavation and earth work. The rate also include charcoal and salt in alternate layers 20mm dia pipe (Light grade) for watering, protection pipe, funnel, wire mesh, PCC chamber in cement concrete (1:3:6) type C-1, 40mm thick RCC 1:2:4) type B-1 cover and CI frame etc. all as specified and directed.

Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5m in depth for taking out cable etc. for repairs/laying cables etc. and getting out in soft/ loose soil all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25cm thick complete all as specified and directed.

Removal of excavated material [soil] to a distance not exceeding 50m and deposting where directed at a level not exceeding 1.5m above the starting point complete all as specified and directed.

M & L for bituminous road cutting to a width of 45 cm and depth 50cm for laying LT UG cables and making good with cement concrete 1:3:6 type C-1 (using 20mm graded stone aggregate) complete all as specified and directed.

Supply, laying, jointing and testing cable XLPE insulated screened PVC bedded galvanised steel strip or wire armoured, electric power cables (heavy duty) with stranded aluminium condutor 1100 Volts grade in trenches/ passing through pipe/fixing on walls, floors etc. incl using suitable clamp of cross sectional area 3.5 core 25 Sqmm all as specified and directed.

Supply & laying of Telerex DWC (Double wall corrugated) HDPE pipe ISI marked of outer dia of 50mm and inner dia 38mm polythylene with smooth internal and profiled external surface for non pressure under ground cable incl couplers & bends all as specified and directed.

Supplying and laying GI tubing light grade of size 40mm dia bore for encasing cable for mechanical protection, laid under Plinth/ Floors/ Paths Culverts or fixed on wall or concealed in wall/floor or along poles or as street light poles or as street light mounting bracket with complete accessories sucha as bends/ sockets/ reducers/ saddles incl necessary threading/ drilling works all as specified and directed.

Supplying, installation, testing & commissioning of following IP 54 Indoor modular type, compartmentalized and sectionalized cubicle panel of suitable size, fabricated from CRCA sheet steel of 2 mm thick while gland plate shall be 3mm CRCA Sheet. LV Switchboard which had been type-tested by an acceptable, multi fold design with impact test IK07-IK10. Chemically treated surface with Multi tank process before painting, epoxy powder coated after two coats of anti-rust primer, making earth connections by providing suitable size of aluminium earth strip. Suitable for operation on 3 phase 415 V 50 HZ AC supply i/c providing and fixing the following switchgear to be mounted there on complete with gaskets, interconnections and earthing. The board shall be dust free, vermin proof and totally enclosed with Degree of protection of IP 54 as per IS 2147, with suitable cable/busbar alleys and shall be mounted on Hot Dip Galvanised MS channels/angle iron frame on floor.

Standard and codes updated and current Indian standard specification and code of practice shall apply to the equipment and the work covered by the scope of this contract, the switchboard shall be form 3b. Busbars shall be of rectangular section hard drawn high conductivity aluminium busbar connections shall be constructed in accordance with the requirements of latest code of IS/IEC standards, All Panels will be type tested assembly and shall be manufactured at OEM factory only and tested as per IEC 61439 -1&2, All indicator lamps shall be protected by 6 Amp MCB, all wiring for relays and meters shall be with FRLS copper conductor wires, The wiring shall be coded and labelled with approved ferrules for identification. The minimum size of copper conductor control wires shall be 1.5 sq. mm. Runs of wires shall be neatly bunched and suitably supported and clamped. Current circuit shall be 2.5 Sq.mm. All ACBs Shall be EDO/MDO (As per BOQ) and MP Based O/C, S/C & E/F Release type only, All T/M MCCBs are Thermal Magnetic O/C & S/C release (As per mentioned in BOQ), Panels to be ordered only after formal approval of general arrangement drawings from Department including dismantling of old unsversible panel with all accessories :- Bus bar - 800 Amps TPN aluminium bus bar

Incomer-1: 500 kVA Transformer : (i). 800Amp 4P 50kA EDO ACB-1 No with set of R-Y-B / ON/ OFF/ TRIP Indicating lamp. (ii). Digital type multifunction meter with R4 485 -1 No with set of cast resin CT's 800/5A

Outgoing : (i). 400Amp 4p 36KA T/M MCCB - 1 No with set of R-Y-B Indicating lamp (ii). 250Amp 4p 25KA T/M MCCB - 5 Nos with set of R-Y-B Indicating lamp. (iii). 200Amp 4p 25KA T/M MCCB 2 Nos with set of R-Y-B Indicating lamp. (iv). 100Amp 4p 16KA T/M MCCB 2 Nos with set of R-Y-B Indicating lamp

Bus coupler : 800Amp 4P 50kA EDO ACB w/o Release - 1 no with set of indicating lamp

Incomer-2: 500 kVA Transformer : (i). 800 Amp 4P 50kA EDO ACB-1 No with set of R-Y-B / ON / OFF/ TRIP Indicating lamp (ii). Digital type multifunction meter with R4 485 -1 No with set of cast resin CT's 800/5A

Note :- Panel should be approved from reputed OEM only and no channel partner shall be entertained. Make : Legrand/ ABB/ Schneider/ GE/ L & T.

Supply, laying and testing cable XLPE insulated, screened, PVC bedded, galvanised steel strip or sire armoured, electric power cables (heavy duty) 1100 volt grade with straded aluminium conductor of size 3.5 core 400 Sqmm all as specified and directed.

M&L for earthing complete with GI earth plate electrode 60x60cmx6mm thick burried directly in ground in earth pit not less than 2.25 mtr depth below normal ground level with top edge of the plate vertically to depth of not less than 1.5 mtr below ground level connected to & including GI strip 32x6mm as earthing lead connecting to equipment by means of GI bolts & nuts etc with provision of charcoal and salt etc all as per electrical plate No-3 of SSR part-I 2009 including RCC cover and MS angle iron frame, watering with GI pipe 20 mm dia (medium grade) & MS funnel, concrete pit including excavation and earthwork in any strata and testing on completion etc. complete all as specified and directed by Engineer-in-charge

Supply & Laying of Telerex DWC (Double Wall corrugated) HDPE pipe ISI marked of outer dia of 200 mm and inner dia 174 mm polythylene with smooth internal and profiled external surface for non pressure under ground cable incl couplers & bends complete all as specified. Make : REX POLYEXTRUSION LTD or its equivalent as approved.

Supply, installation, commissioning of water cooler fully stainless steel, electric driven single phase having approx storage and nominal cooling capacity of 150 Litres per hour all as specified and directed. Make: Bluestar/ Voltas

Supply and fix refrigerator, electric driven (single phase) capacity 310 Litres BEE 5 star rated double door, frost free including all connecting lead and suitable 3 pin plug top complete all as specified and directed. Make : Whirlpool/ LG/ Samsung.

Supply, installation, commissioning of Glass Top Deep freezer single phase 240 Volt, 50 Hz of capacity 320 litres and double door all as specified and directed. Make Bluestar/ Voltas

Supply & fix GI tubing medium grade 15mm dia complete with accessories including cutting and screwing the existing pipe line for connection purposes including cutting, chasing and cementing and POP all as specified and directed.

Supply & fix Gun metal gate valve with iron wheel head, ISI marked, screwed both ends for iron pipe and fixed for pipe 15mm. Make : Leader/ Zoloto/ Seiko.

S & F PVC connection 15 mm size with PTMT nuts of length 600 mm long complete all as specified by EIC.

Aishwarya Constructions

SHINDE DHEERAJKUMAR SIDRAM

Vastushilpa Contrustion