SPECIAL REPAIRS TO BUILDING NO P-19 AND P-22 AT CQAE (WE) BANGALORE

Amount

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles and rubbish off the premises complete all as specified and directed.

Roughening surfaces of old concrete floors by picking, sweeping clean and washing down with water to remove dust, etc complete all as specified and as directed.

Demolition of cement concrete (un reinforced) in ground floor and paving n.exc 15cm thickness below or above ground level, complete all as specified and directed.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed.

M & L for Removing building materials etc to a distance of exc 1km but n exc 5 km or under, beyond the lead included in the rates, including loading, unloading and stacking at the destination

M&L Vitrified ceramic light shade tiles of 10mm thick and area of each tiles not exceeding 0.36 Sqm in floors set and jointed neat cemet slurry and pointed in white or coloured cement to match for flooring flooring over and including 15 mm thick screed bed in CM 1:6 all as specified and directed.

M&L Vitrified ceramic light shade tiles of 10mm thick and area of each tiles not exceeding 0.36 Sqm in skirtings and jointed neat cemet slurry and pointed in white or coloured cement to match for skirtings over and including 10 mm thick rendering in CM 1:4 in dado/skirting all as specified and directed.

M&L Non skid coloured Ceramic tiles 7 to 8 mm thick and area of each tiles exc 0.11 sqm but not exceeding 0.18 Sqm as in flooring set and jointed neat cemet slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:6 all as specified and directed.

M&L Glazed coloued Ceramic tiles of size 350X250X7mm/450X350X7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match as in skirting/dado over and including 10 mm thick rendering in CM 1:4 finished all as specified and directed in toilets ang kitchen all as specified and directed.

M & L for Polished Sadarhalli stone work with18-20mm thick slab, table rubbed and polished, in steps (Riser/tread/landing) and like in single piece set in neat cement slurry and pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite laid over and including 15mm thick screed bed or bedding layer in cement mortor (1:4) complete all as specified and directed.

M & L for 25mm thick Cement concrete type B-1, 1:2:4 (20mm graded aggregate) as in floor fininsh all as specified and directed.

S&F in repair Kitchen sinks with drainage board made of stainless steel 1 mm thick with plugs, washers and wastes, including bedding in cement mortar to wall with all fixing arrangements of overall size 915x460mm and bowl size 410x330x160mm all as specified and directed. Make : Nirali/ diamond/Blue star

M & L for Granite work with 20mm thick slab, table rubbed and polished, in steps, window cills, cooking platforms and like in single piece set in neat cement slurry and pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite laid over and including 15mm thick screed bed or bedding layer in cement mortor (1:4) complete all as specified and directed.

S & F Waste fittings, 32mm brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed

Taking down cement plaster of any description on brick or stone walls etc including racking out joints hacking for key scrubbing down with water etc complete all as specified and directed.

M & L for Hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface in brocken stone or boulders all as specified and directed.

M & L for 75mm thick PCC 1:3:6 type C2 (using 40mm graded stone aggregate) as in plinth protection finished even & smooth without using extra cement complete all as specified and directed.

M & L for Flush pointing to squared rubble masonry, coursed or uncoursed in cement mortar 1:4 complete all as specified and directed.

M & L for plaster to top of chajja with cement mortar 1:4, 10mm thick complete all as specified and as directed up to a height of 10 Mtrs including all formwork all as per directions of Engr-in-charge

Supply only liquid water proofing compound

M & L for Reinforced cement concrete, 1:2:4 type B-0 (using 12.5mm graded stone aggregate) as in slab supported on walls, beams and columns in floor, roofs, landings, balconies, canopies, shelves ,chajja and like complete all as specified and directed for concreting up to a height of 10 Mtrs all as per directions of Engr-in-charge

S&F Mild steel TMT bars 10mm dia and over, cut to length bent to shape required including cranking bending spirally for hooping for columns hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed. for placing of reinforcement up to a height of 10 Mtrs all as specified and directed.

S&F Mild steel TMT bars 6 to 8mm dia and over, cut to length bent to shape required for stirrups,spacers and binders all as specified and directed.

M & L for Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) for rough finished flat surface complete all as specified and directed.

M & L for Formwork to chullah hoods, chajjas, troughs and similar items in rough finished in flat surface including edges all as specified and directed.

M & L for Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roof slabs and shelves, sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 5cm but not exc. 10cm wide in rough finished flat surfaces of concrete all as specified and directed.

M & L for Rendering 10mm thick plaster in cement mortar 1:6 on stone masonary or surface other than fair faces of brick work finished even and smooth without using extra cement complete all as specified and directed

M & L 15mm thick rendering in cement mortar 1:4 mixed with water proofing compound on fair faces of stone masonry surfaces finished fair and even without using extra cement complete all as specified and directed

M & L for Rendering 5mm thick plaster in cement mortar 1:3 on brick or concrete surfaces as in ceiling, finished even and smooth without using extra cement complete all as specified and directed

Removing existing unservicable tar felt on any type of any description from roof slab along with sceed bed , cleaning the surface and removing the debris to a distance exc 1km to 5km from starting point and directed

Dismantling & removing existing sunken floor filling from sunken slab concrete complete all as directed and specified

Taking down old damaged CI/PVC waste pipes of any dia in sunken floors complete all as specified and directed

Supply only acrylic based polymer water proofing compound ISI marked (Make: conplastx 421 IC of M/s Fosroc chemical Ltd or equivalent)

M & L for APP based polymeric bitumen primer @ 0.20 Kg/sqm and providing 4mm thick APP Modified water proofing membrane weighing not less than 4.0 Kg/Sqm reinforced with non woven polyster matt weighing not less than 160 gm/sqm having softening point not less than 150 degress centigrade having tensile strength of 650N/5cm and 350N/5cm in longitidunal and traverse directions respectively of the reinforcement , tearing strength of 180 N by torch application including min10cm side over lap & 15cm end lapsand applying a coat of blown bitumen @ 1.20 kg/sqm hot bitumen 90/15 over and below them membrane finished all as specified and directed by Engr-in-charge

M & L for 40mm thick Cement concrete type B-0, 1:2:4 (12.50 mm graded aggregate) as in sub base of fooring .

M & L for 15mm thick rendering in cement mortar 1:4 on fair faces of brick work or concrete surface is to be finished even and smooth without using extra cement

M & L cement concrete type E2 1:5:10 (40mm graded aggregate) in foundations, filling and mass concrete

Applying three coats of brush bond acrylic based cementitious material of approved quality (Dr. Fixit- Pidifin 2K or Brushbond RFX of Fosroc India (P) Ltd. or equivalent) for sunken portion treatment all as per manufacturer instruction and providing 150micron thick polythene film over bitumen primer @ 0.5 kg /Sqm all as specified

Demolition of brick or stone boulder masonary built in cement mortar including all quoins, arches, pillar etc complete all as specified and directed.

M & L brick work with sub class B bricks in CM 1:4 staright or curved on plan exc 6m mean radius .

Demolition and breaking up Salt glazed stone ware/ AC Reinforced concrete pipes 150mm dia,laid in trenches set in cement mortar incl PCC bed all as directed .

Dismantling of cast iron/RCC/PVC drain pipes jointed in cement mortar and taking out of trenches or walls of 150mm bore including fittings.

Taking up or down 25mm steel tubing and connections.

Taking up or down 20mm steel tubing and connections.

Taking up or down 15mm steel tubing and connections.

S&F CPVC pipes 25 mm SDR 11 & Plain VPVC SDR 11 on walls, ceiling orf laying including fitting in floors all as specified and as directed .

S&F 20 mm dia of CPVC pipes SDR 11 and plain CPVC SDR 11 fittings on walls / ceiling or laying in floors complete all as specified.

S & F in repairs Stop valves, brass, fancy type, chromium plated 15mm bore with long shank and cup (concealed type), screwed down high pressure, with capstan head handle, screwed both ends for iron pipe or for unions and fixed . Make : Jaquar, Cera or equivalent as approved by GE

S & F in repairs 25mm dia gun metal glove or Gate valve with iron wheel head screwed both ends for iron pipe or for unions and fixed .

S & F Angle valve two way, brass, chromium plated, fancy type, with capstan head handle screwed down high pressure, including CP brass wall flanges; screwed for 15mm bore pipe connection fixed in repairs complete all as specified and directed. Make : Jaquar, Cera or equivalent as approved by GE

S & F in repairs Shower rose, brass, chromium plated, 125mm dia with or without swivel joint, with & including CP brass arm and wall flange, fixing to steel pipe or union as in repair complete all as specified and directed. Make : Jaquar, Cera or equivalent as approved by GE

S & F in repairs Pillar tap, cast copper alloy, chromium plated, fancy type, with capstan head handles with lettered 'hot' and 'cold', screwed down high pressure, with long screwed shank and fly nuts suitable for 15mm bore pipe connection complete all as specified aqnd directed . Make : Jaquar, Cera or equivalent as approved by GE

S & F in repairs Bib taps, brass, chromium plated, fancy type, long nose, with capstan head handle screwed down high pressure, including CP brass wall flanges; screwed for 15mm bore pipe connection complete all as specified and directed. Make : Jaquar, Cera or equivalent as approved by GE (Kitchen)

S& Fin repair Two way taps cast chromium plated with crutch or butterfly handle, screwed down, screwed and fixed including all as specified and as directed (EWC) (Make: Cera or equivalent as approved by GE)

S&F Brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixed for 15mm bore pipe.

S&F in repairs 10 litre capacity PVC syphonic action type for low level flushing cistern including all fittings and including flushing pipe fixed in repair all as specified and as directed. Make : Cera/Parryware/Neycer

S & F PVC connection heavy duty with PTMT nut & washers for both ends of size 15mm dia and 600mm long complete all as specified.

S & F in repair Health faucet, brass, chromium plated, with 900mm long 15mm bore chrome finish flexible pipe, complete all as specified and directed. Make - Jaquar, Cera or equivalent as approved by GE

S&F in repairs vitreous china wash basin, white or coloured of size 550 x 400 mm with padestal including brackets all as specified and as directed . Make : Cera/Parryware/Neycer

S & F in repairs Vitreous China wash down water closet pan (Pedestal Pattern) white including fixing bolts connecting to flushing cistern complete all as specified including plastic water closet seat white, closed pattern with flat bottom and cover and chromium plated hinging device all as directed.

S & F Ball valve high pressure of PTMT with epoxy coated aluminium rod & high-density plastic ball screwed for iron pipe of size 20 mm dia fixed in repair complete all as specified and directed.

S&F in repair brass Chromium plated Tubular towel rail, 20mm dia, D type, 60cm long between flanges

S&F 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or in floors .

S&F 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls and connection pipe for water outlet from vernadah's

S & F S Trap for 110/110mm bore

S & F P Trap for 110/110mm bore

S & F 110mm PVC (SWR) WC connector bent type

S&F PVC (SWR) bends of any radius, 110 mm bore

S&F PVC (SWR) branch piece single Y equal or unequal 110 mm bore

M&L for PVC (SWR) floor trap plain, diameter of out let 75mm with grating including jointing with solvent cement.

M & L for 100mm dia CI nahani trap with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed.

M L for Low density polytheyene pipes (LDPE) 50mm bore pipe of rating 6 kg / sqcm as in spout complete all as specified and as directed.

Taking down door chowkats or frames exceeding 1.5 sqm but n exc 4 sqm with shutters (without taking off shutters from the frame) of any description

Taking down door chowkats or frames not exceeding 1.5 sqm with shutters (without taking off shutters from the frame) of any description

Taking down shutter of any description exc 1 Sqm and n. exc 2 Sqm each complete complete all as specified and as directed.

Refixing door wooden of any description exc 1sqm and not exc 2sqm each in same opening after taking down, easing and adjusting and also refixing builders hardware as required; complete all as specified and directed.

Taking down steel window/ventilators shutter exc 1sqm but n exc 2 sqm (Without taking off shutters from the frame) including making good of demolished wall portion complete all as specified and directed by Engr-in-charge

M & L for Framed work such as grills framed guard bars and similar work confirming to Fe 290, grade E-165.

S & F aluminium strips for doors including all fittings all as per direction of Engr-Inc-Charge

Cutting holes in stone walls built in cement mortor for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as required exc one brick but n exc two brick thick.

S & F 25mm dia decorative powder coated drapery curtain rods of with bright finish, including decorative side domes, and a minimum complete all as directed by Engineer In Charge.

S & F brackets for curtain rods design type all as specifed and as directed by Engr-in-charge

S & F 2nd class Hard wood plain solid straight chowkhats and frames wrought, framed rebated on the solid rounded or chamfered put together with glue pinned at joints all as specified and directed.

M & L for 35mm thick, factory made, plain,framed, panelled shutter (two panel) of second class hardwood with lock rail and panel of 9mm B.W.P. commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed.

M & L for 30mm thick, factory made 2nd class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a);complete all as specified and as directed.

M & L for Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples and fixed with tinned tacks or galvanised wire stapels complete all as specifed and directed.

S&F Factory Made Solid PVC frame (Single Rebated) of size 60mm x 30mm made out of solid PVC foam with homogenous fine cellular structure having smooth outer integral skin with suitable metal stiffner and fixed with 100 x 8 sheet metal CSK screws complete all as specified and as shown on drawing (Note :- Door frame shall be water proof, termite proof, elegant and should have excellent screws holding strength to fix hinges and hold doors properly for a long life)

S&F Factory Made Solid PVC Moulded Door Shutter With Particle Board Core, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing

Dismantling boarding any description, fixed in any position with nails complete all as specified and as directed.

M & L for 18/19mm thick Prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work complete all as specified and directed.

M & L for 12mm thick block board grade 2 quality interior grade, commercial type

S & F Hasp and staple, 100 mm size safety type, aluminium anodised, including bolt to hinge plate and fixed with screws complete all as directed.

S & F Ball catches with 8mm dia steel ball and brass body and striking plate including letting in and fixed complete all as per specified and directed.

M & L for brass Drawer handles, projection drop (50mm to 65mm) on screwed plate complete all as per specified and directed.

S& F Brass Mortice lock with two levers (vertical type) on panelled door, mild steel body complete all as specified and as directed.

S&F 150mm Aluminium alloy, anodised, sliding door bolt with hasp & staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy complete all as specified and directed.

S&F Butt hinges medium weight cold rolled,mild steel100 mm size

S&F Alumunium anodised barrel tower bolt of exturded section of size 150 mm long

S&F Extruded aluminium alloy handles, fabricated type,anodised of size 150 mm.

S & F 150mm Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and directed.

S&F 600mm long Mild steel Peg stay for hanging cloth etc complete all as specified and as directed

S & F in repairs Brass knobs 35 to 40mm dia of size suitable for cupboard and as approved by GE, complete all as specified and as directed.

S & F 3 mm thick Sheet glass, ordinary quality and fixing with aluminium frame work in squares not exceeding 0.5 Sq. M in each pane

S & F MS continuous (Piano) hinge bright finish or electro galvanised with width of flap 30mm (when open) complete all as specified and directed.

M & L for Providing and injecting chemical emulsion for Post Constructional Antitermite Treatment of soil under existing floors using chemical emulsion at the rate one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 to match the existing floors. complete all as specified and as directed.

M & L for Providing and injecting chemical emulsion for Post Constructional Antitermite Treatment along the external wall below concrete or masonry apron using chemical emulsion at the rate of 2.25 litre per linear metre including drilling and plugging holes tec in apron complete all as specified and as directed.

M & L for Providing and injecting chemical emulsion for Post Constructional Antitermite Treatment at points of contact of wood work by chemical emulsion (in oil/or kerosene based solution) at the rate 0.50 litres per hole by drilling 6mm dia holes at a down ward at angle 45 degree at 150mm centre to centre and sealing the same complete all as specified and as directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for

M & L for 40mm thick floor finish concrete type B-1,1:2:4 (20mm graded aggregate) including finishing even and smooth

S&F 1mm thick Mild steel, plain, black sheet in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required etc. complete

S&F Fe 410 - W (Gde-E- 250) quality-A Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete

M&L for Preparing the new surfaces of wall and applying two coat of oil bond distemper over a coat of interior wall care putty 3mm thick all as specified and as directed

M&L for Complete removal of existing surface finish and applying two coat of OBD over a coat of 3mm thick wall care putty all as specified and directed

M & L for three coats of white wash on new plastered ceiling surfaces including preparation of new surfaces

M & L for complete removal of existing treatment preparation of old surface of ceilings and applying two coat of white wash on old ceiling surfaces including preparation of old surfaces

M & L for three coats of white wash on new plastered wall surfaces including preparation of new surfaces

M & L for complete removal of existing treatment preparation of old surface of walls and applying two coats of white wash on old wall surfaces including preparation of old surfaces

M & L for Preparation of old wooden painted surface not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

M & L for Preparation of new wooden surfaces exc 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M & L for Preparation of old painted steel surfaces exc 10 cm width or girth and applying one coat of synthetic enamel paint , complete all as specified and directed.

M & L for Preparation of new or previously untreated steel surface of any description exc 10cm with or girth an applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M & L synthetic enamel paint on old wall surface for writing letter or figures (Block, Roman, Italic or indian ) n exc 30cm in high on wall surface

Dismantling of water storage tank of capacity exc 500ltrs & not exc 1000ltrs and removing to store yard.

S & F Rotational moulded polyethylene water storage tank of 1000Ltr capacity (cylindrical vertical with closed top), triple layered, white in colour hoisted and fixed in position incl all accessories complet all as specified and directed. Make : Sintex, Star, Poly con, Fusion.

S & F powder coated aluminium three sliding window, ventilator , louvers with frame comprising of aluminium frame (track) with gradetrack of size 92.5x31x1.50mm fixed to walls and two Nos of sliding shutters 5mm thick tinted glass and one Nos sliding shutter with stainless steel wire cloth0.36mm nominal dia of wire and average width of apearature 1.40mm including necessary rubber gaskets and aluminium beadings & clips if 0.90mm thick etc and finished with metal plate on gaps of the surface in contact with masonary walls and necessary handles and locking arrangements all as specified and as directed.

M&L washing rubbing down and stoping of new painted wall surfaces and applying two coat of weather proof paint all as specified and directed.

M&L for complete removal of existing treatment preparation of old surface of walls such as washing rubbing down and stoping of old painted wall surfaces over a coat of primer over a coat of 1 to 3mm thick wall care outty and applying two coats of weather proof paint all as specefied and directed.

Excavation in trenches not exceeding 1.50m wide and not exceeding 1.50m in depth for fdn for shafts, wells, cesspits, manholes pier holes n.exc 10Sqm on plan and getting out soft/loose soil complete in any type of soil complete all as specified and directed.

Returning filling in including spreading leveling, watering and well ramming in layers n.exc 25cm thick in soft/loose soil complete all as specified and directed.

Removing of excavated soils to a distance n.exc 50m and depositing where directed by the Engr-in-Charge at a level n.exc 1.50m above the starting point complete all as directed

Demolition and breaking up Salt glazed stone ware/ AC Reinforced concrete pipes 150mm dia,laid in trenches set in cement mortar incl PCC bed all as directed.

M & L cement concrete type D2 1:4:8 using 40mm graded stone aggreagate as in foundation, filling and mass concrete

M/L for concrete bed to drain pipes in PCC 1:3:6 type C2 using 40mm graded stone aggregate including packing under and haunching against sides of pipes after they are laid and tested for 110mm dia pipe

S&F PVC(SWR) Pipes 110mm dia single soketed, in any length with rubber ring joints, laid in trenches or in floors

M&L PCC 1:2:4 type B1 using 20mm traded stone aggregate as in Coping /benching of manholes including eatherlng,rounded /chemfered angles and throating as directed including necessary form work and finishing all exposed surfaces of concrete even and without using extra cement complete all as specified and as directed.

Demolition of cement concrete (reinforced) of any description and in any position not otherwise specifically provided for complete all as specified and directed.

M&L for Precast RCC cover slabs for manholes 1:2:4,type B1,using 20mm graded stone aggregates,set in CM 1:4 including necessary form work and finishing the exposed surfaces of concrete even and without using extra cement complete all as specified.

S&F Mild Steel TMT bars 10 mm dia and over , cut to length bent to shape requried including cracking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips all as specified and as directed.

Demolition of brick or stone work built in cement mortar including all quoins, arches, pillar etc complete all as specified and directed.

M&L for brick with subclass 'B' bricks straight or curved on plan exc 6 m mean radius built in CM 1:6 complete all as specified and directed.

M&L for rendering 15 mm thick in CM 1:6 on fair faces of brick work finished even and smooth without using extra cement complete all as specified and directed.

M & L for Cutting into existing manholes 100mm dia for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-l smooth finished, and reforming benching as required

Taking down copper/aluminium point wiring(light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc.removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc.

Taking down DBs including MCCB`s/MC B`s 415 Volt/230 Volt all as specified and directed.

Taking down old aluminium sub main wiring of any size all as specifiede and directed.

Taking down sheet metal enclosures of any type any capacity all as specified and directed.

Taking down earth plate including accessories all as specified and directed.

M&L for Point wiring complete as specified with 1100 volt grade 1.5sq.mm. (nominal area) single core PVC insulated unsheathed cable multi-stranded copper conductor drawn through and including rigid non-metallic PVC conduit of suitable size but not less than 20mm dia , with all fittings, fixed on wall surface including decorative modular cover plates (inner and outer) suitable for housing modular pattern switches/ sockets/ regulators etc. along with necessary metal sunk boxes flush mounting in the wall duly earthed with 1.5sqmm cable as for wiring above but green in colour as continuous earthing wire complete all as specified and directed.

One light point controlled by one 5 amp switch one way

One Ceiling/Exhaust fan point controlled by one switch 5 Amps one way.

One light point controlled by two 2-way switches.

One 3 pin 5 Amp socket out let on independent board.

One 3 pin 5 Amps switch socket combination on same Board

One bell point controlled by one bell push switch 5 Amps one way.

All as per item No.150 above but point wiring with 2 runs of 2.5 sqmm PVC insulated multistranded copper conductor and single run of 2.5 sqmm copper conductor as earth continuity conductor suitable for one 3 pin 15 Amps socket out let on independent board.(For power point).Note: Power point should be connected from DB with MCB control.

S & F Modular switch 6 Amp one way 1 module 230 V AC

S & F Modular switch 6Amp two way 1 module 230 V AC

S & F Modular switch 16 Amp one way 1 module 230 V AC

S & F Modular socket 6 Amp 2/3 pin combined 2 module with pilot lamp working on 230 V AC

S & F Modular socket 6Amp/16Amp 5/3 pin multiple combined 2 module working 230 V AC

S & F Modular fan regulator step type 120W 2 module complete all as specified.

S & F Modular bell push 6 Amp one way 230 V AC

S/F Ceiling rose PVC polycarbonate , isolated body 3 terminals 230 V complete.

S & F , Electric Bell, working on 230 volts AC supply complete all as directed.

Taking down exisitng ceiling fan of any size and any capacity and M&L for painting and writing MES No. of ceiling fan complete in suitable with synthetic enamel paint by spraying including filling cavities with filler, one coat after cleaning all dust etc and refixing the same location complete all as specifed and directed.

Taking down exisitng Exhaust fan of any size and any capacity M&L for painting and writing MES No. of exhaust fan complete in suitable with synthetic enamel paint by spraying including filling cavities with filler, one coat after cleaning all dust etc and refixing the same location complete all as specifed and directed.

S & F Exhaust fan 300mm sweep,working on single phase 230 volts, 50Hz AC supply metal body complete with louvres electric connection from ceiling rose to fan connector with PVC insulated 3 core copper cable of suitable size of 0.75 sq mm complete all as specified and directed.Make: Havells/Bajaj/CG.

M & L for core cutting of brick wall in round shape for fixing of exhaust fan of capacity 300mm sweep as per site requirement all as speicified and directed.

S & F Energy Efficient BEE 5 star rated water heater storage type of 25 liters capacity, vertical electric supplied and installed complete including flexible pipe for hot and cold water, dead weight pressure relese valve, Anchor fastner - 4Nos of suitable size all as specified and directerd. Make: Havells(Model: Puro/Bajaj/Racold.

S & F Sub main wiring with PVC insulated FRLS multistranded copper cable 2 runs of 6 sq mm 1100 V grade with stranded copper conductor in and incl rigid PVC conduit surface on wall (ISI marked) incl all specials like joint elbow, Tee, junction, etc and provision of PVC insulated FRLS copper conductor single run of multistranded copper cable green colour 6.0 sq mm for earth continuity all as specified and directed.

S & F Sub main wiring with PVC insulated FRLS multistranded copper cable 2 runs of 4 sq mm 1100 V grade with stranded copper conductor in and incl rigid PVC conduit surface on wall (ISI marked) incl all specials like joint, elbow,Tee,junction, etc and provision of PVC insulated FRLS copper conductor single run of multistranded copper conductor green in colour 4.0 sq mm for earth continuity all as specified and directed.

S & F TP&N 04way vertical type sheet steel powder coated distribution board double door with 200amps rated bus bar suitable for MCCB fixing as incommer and MCB`s fixing as outgoing Neutral link, Earth Bar and Din rail IP-43 protection, door earthing, mechanical, impact strength IK 08, insulated bus bar assembly working on 415 V, 50 Hz AC supply all as specified and directed.

S & F SP&N 12way horizontal type sheet steel powder coated distribution board double door with 200amps rated bus bar suitable for MCB fixing as incommer/out going Neutral link ,Earth Bar and Din rail working on 240 V, 50 Hz, AC supply all as specified and directed.

S & F MCCB FP 125 Amps, 16 KA ,working on 415 volts, 50Hz AC supply all as specified and directed.

S & F for Earth leakage protection RCCB FP,63 Amps, 300mA,working on 415 volts, 50Hz, AC supply all as specified and directed.

S & F RCCB DP 40 amps, 300mA, 240 volts, 50Hz AC.

S& F MCB SP, 6-32 amps,10 KA, 240 volts, 50Hz, AC.

S & F surface mounted 20watts 4 feet LED tube light fitting with smart bright is a reliable and affordble system that delivers to with very high efficiency and connection by flexible PVC cable with stranded copper conductor from ceiling rose to connector of the fitting including complete all as specified and directed.

S & F surface mounted 10watts 2 feet LED tube light fitting with smart bright is a reliable and affordble system that delivers to with very high efficiency and connection by flexible PVC cable with stranded copper conductor from ceiling rose to connector of the fitting including complete all as specified and directed.

Supply and fixing lamp holder pvc/polycarbonate type with back plate sutable for batten fitting all as specifed and directed.

Supply and fixing of 10 watts LED lamp type B22 all as specifed and directed.

S & F single pole and neutral enclosure with two pin and earth plug and soket with one sinle pole MCB 20Amps 240volts all as specified and directed. (For Geyser).

S & F building security luminaire with high power skyline LED and ensure uniform distribution, maintanance free system, 45watts LED light fittings IP-66 protection including suitahle down rod, clamps, nut, bolts and other related items for fixing on the wall/surface suitable for 230volts, 50Hz AC supply all as specified and directed. Make: Wipro/Phillips/CG/Havells

S & F communication modules for TV socket sap code no.ACAKTOW000. Make: Havells(crabtree)Roma(Anchor)/Legrand.

Taking down existing Enery meters carefully disconnecting the incoming and out going electric wire connection and keeping in safe custody including recorded the SI No. meter reading and Qtr No/Circuit No. to the meter complete all as specifed and directed.

Supply, installation,testing and commissioning of factory made meter panel board of size length 1.5mtr,height 1.04mtrs and depth 0.35mtr suitable for wall mounted/floor mounted made out of CRCA sheet of 2mm thick indoor type totally enclosed weather proof, dust vermin proof with front openable, hinged door locking arrangement mounted on MS clamp welded to panel body grouted in wall including provision of Acriylic sheet for meter reading, space for refixing of single phase KWH meters-07Nos, and VTPN DD DB-01Nos. AC 230volts including lugs, spacer mounting channels, rubber gasket, locking knobs, PVC shrinkable sleeves, nut bolts, washers etc. epoxy poweder coated spray paint with primer complete all as speicifed and directed.

Earthing complete with galvanised earth plate electrode 60 cm x 60cmx 6.15 mm thick, buried directly in ground vertically (earth pit not less than 2.25 m deep below ground level) with top edge of the earth plate not less than 1.5m below ground level , connected to GI earth wire 4 MM Dia as earthling lead by means bolts and nuts check nuts and washers of galvanized iron and connected to main switch board including watering arrangement with PCC chamber , MS funnel with wire mesh,. CI cover with frame etc including necessary excavation in any type of strata , returning, filling removal of soil outside MD land ,filling of charcoal and salt complete all as shown in electrical plate No. 3 of MES Sch Part I , connected to Earthing test point all as specified and directed on testing on completion. Note: The contractor should note down the ER values and obtain signature from user and submitted to the department.

Excavating in trenches not exceeding 1.5m wide and not exceeding 1.5m in depth for laying of cable, foundation etc, and getting out in hard /dense soil all as directed.

Returning filling in including spreading, leveling Watering and well ramming in layers not exceeding 25cm all as directed.

Removing excavated surplus soil to a distance not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point all as directed.

Supply and spread river sand in trenches, as in cable cushioning all as directed. Note :- Punned thickness will be considered for payment.

Brick protection cover on cable with sub class 'B' brick, laid dry and flat adjacent to each other complete all as specified.

Taking down LT UG cable of any type any any capacity all as specified and directed.

Taking down GI tubing of any type any capacity all as specified and directed.

Supply, laying and testing Insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 3.5corex50sqmm cable all as specifed and directed.

Boring of holes under road, pavement and hard standing by trenchless method by adopting horizontal boring using ultra sound technique and necessary machine specified and as directed.

Taking down gate valve of any type any capacity all as specified and directed.

Supply and lay in repair of GI tubing medium grade (ISI marked) laid in trenches including all fittings such as bend, tea, union, elbow etc complete including testing for 50mm bore sizes all as specified and directed.

Supply and lay in repairs of GI tubing medium grade (ISI marked) laid on wall including all fittings such as bend, tea, union, elbow etc complete including testing for 25mm bore sizes all as specified and directed. Note: Rate including cutting of wall where as required and as per site requirement.

Supply and lay in repairs of GI tubing medium grade (ISI marked) laid on wall including all fittings such as bend, tea, union, elbow etc complete including testing for 15mm bore sizes all as specified and directed. Note: Rate including cutting of wall where as required and as per site requirement.

S & F gate valve cast copper alloy, screw down alloy, screw down high pressure with crutch or butterfly handle screwed both ends for iron pipe or union fixed all as specified and directed.

Excavation in trenches not exceeding 50m wide and depositing where directed at level not exceeding 1.5m above the starting level all as directed at site.

G K CONSTRUCTIONS

ROHAN BUILDERS

Vinayaka Enterprises

chowdeshwariconstructionco

OM INFRA

SHANKAR