REPAIR TO LEAKAGE SEEPAGE, SUNKEN FLOOR TREATMENT ,ROOF TRATMENT,ROOF COVERING WK AND REPAIRS TO JOINERY, FLOORING,PLASTERING, PLUMBING, SANITARY WORKS AND CERTAIN B/R WORKS OF MD ACCN OTHER THAN OFFRS AT CHAFB

Amount

Demolition of plain cement concrete of any description and in any position complete all as specified and directed. Note: All debris and rubbish shall be removed from MOD land during or at the end of each working period at his risk and cost in accordance with all applicable federal, state, and local regulations.

Dismantling floor, hearth or wall tiling incl cement mortar bedding ( but not backing) and rubbish off the premisies complete all as specified and directed. Note: All debris and rubbish shall be removed from MOD land during or at the end of each working period at his risk and cost in accordance with all applicable federal, state, and local regulations.

Providing water proofing treatment with best quality acrylic polymer modified cementitious composite slurry coating approved brand over sunken floors & terraces.The surface to be treated shall be clean from all debris and loose particles. All debonded particles shall be removed with wire brush and the surface should be clean and in SSD (Saturated surface dry) condition prior to the application. Providing water proofing treatment with , acrylic polymer modified cementitious composite slurry coating of approved brand at recommended rate as per manufacturer @ 2mm in 2 coats over the sunken slab as per technical specifications complete all as specified and directed. Make:sika/dr fixit/asian smartcare/fosroc

M&L Rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:3 mixed with waterproofing treatment chemical using integral waterproofing Fosroc Conplast X421IC or techno commercially equivalent from SIKA / Dr fixit / asian smart care conforming to IS:2645 as per manufacturers instruction complete all as specified and as directed. Note : WPC shall be measured and paid seperately.

Supply only integral WPC complete all as specified and directed.

M&L Plain cement concrete type F2 1:7:12 using 40mm graded aggregate as in foundations, filling and mass concrete in sunken floor complete all as specified and as directed.

M&L Non-skid coloured ceramic tiles 7 to 8mm thick (square /rectagular) area of each tile exc 0.06 sqm but n exc 0.11 sqm in floors set jointed in neat cement slurry and pointed in white or coloured cement to match incl screed bed 15 mm thick of CM 1:6 complete all as specified and directed.

M&L 25mm th cement concrete 1:2:4 type B0 using 12.5 mm graded stone aggregate as in sub base for flooring finished even and fair complete all as specified and directed.

M&L Non-skid ceramic tiles 7 to 8mm thick (square /rectagular) area of each tile exc 0.11 sqm but n exc 0.18sqm in floors set jointed in neat cement slurry and pointed in white or coloured cement to match incl screed bed15 mm thick of CM 1:6 complete all as specified and directed.

M&L Glazed ceramic coloured tiles in vertical surfaces 350 x250x7/450x350x7 mm thick , set and jointed in neat cement slurry and pointed in white or colour cement to match laid over 10mm thick cement mortar in CM 1:4 complete all as specified and directed.

M&L Cementous Grouting where heavy leakage (5 Nozzles per SQ.MTS) as specified hereafter :- Thoroughly clean the surface of slab with wire brush and fill the slab area to check the water tightness of the RCC slab / sunken slab prior to waterproofing treatment. Mark the leaking points and treat them to make the leaking spots watertight using injection cement grout mixed with MasterFlow 150 or low viscous epoxy grout using Master Inject 1315 by drilling the hole and fixing the nozzles using Master Emaco S 348 or equivalent (BASF/Fosrock/ Sunanda/ kerakoll/ Mapei) Note: Rate shall be inclusive of cement.

M&L Cleaning the joints of tiles in bathroom/Toilet/Kitchen flooring by removing with wire brush or any other means/material and make suitable for applying chemicals for joints.The joints to be filled with Nitotile EP gront of FOSROC or with approved techno commercially equivalent chemical and top coat to be filled with white or colour cement match to tile surface complete as directed by the Engineer-in-Charge. Note:Quoted Rate shall be inclusive of cement.

Demolition of brick work/stone boulder masonry , built in cement mortar incl all quoins, arches pillars etc but excluding ashlar facings complete all as specified and directed. Note: All debris and rubbish shall be removed from MOD land during or at the end of each working period at his risk and cost in accordance with all applicable federal, state, and local regulations.Demolition item considered under

Taking down cement plaster on brick or stone wall , concrete surface etc. including racking out joints, hacking for key ,scrubbing down with water etc. (Note: All debris and rubbish shall be removed from MOD land during or at the end of each working period at his risk and cost in accordance with all applicable federal, state, and local regulations).

M&L Rendering 15mm thick in cement mortar 1:4, on fair faces of brick work/concrete surfaces finished even and smooth without using extra cement complete all as specified and as directed.

M&L Rendering 10mm thick on fair faces of brick work or concrete surfaces in cement morter 1:6 finished even and smooth without using extra cement complete all as specified and as directed.

M&L Rendering 5mm thick on concrete surfaces of ceiling in cement morter 1:3 finished even and smooth without using extra cement complete all as specified and as directed.

M&L Preparing old plastered or unplastered surface of walls and applying two coats of cement base paint on walls complete all as specified and directed.

M&L Preparation of new plastered surfaces of ceiling and applying two coat of white wash complete all as specified and directed.

M&L Preparation of new plastered surface of wall and applying two coats of oil bound distemper over a coat of chalk primer whitening complete all as specified and directed.

M&L Preparing plastered or unplastered new surface of walls and applying three coats of white wash on walls complete all as specified and directed.

M&L Precast cement concrete block masonry with solid blocks,in PCC 1:3:6 Type C1 (20mm graded aggregate) exc. 10 cm in width and setting in mortar1:6 complete all as specified and as directed

S&F 110mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to wall including dismantling of old pipe (sewage/rain water/any type) complete all as specified and as directed. General Notes for SL Item No 23.00 to 48.00 :- Quoted rate shall deemed to include cost of scaffolding or ladders etc required for approaching for repair work ( Ground floor to Seventh Floor).

S&F 75mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to wall including dismantling old pipe (sewage/rain water/any type) complete all as specified and as directed.

S&F 75mm dia PVC (SWR) bend with access door of any radius complete all as specified and as directed.

S&F 110mm bore PVC (SWR) bends of any radius complete all as specified and as directed.

S&F 75mm bore PVC (SWR) bends of any radius complete all as specified and as directed.

S&F 110mm bore PVC (SWR) bends with access door of any radius complete all as specified and as directed.

S&F PVC (SWR) double branch piece (double Y), with access door 110 mm bore complete all as specified and as directed.

S&F PVC (SWR) Branch piece single equal or unequal with access door 110mm bore all as specified and as directed.

S&F PVC (SWR) junction single (Single T) equal or unequal with access door 110mm bore complete all as specified and as directed.

S&F PVC (SWR) junction single (Single T) equal or unequal with access door 75mm bore complete all as specified and as directed.

S&F PVC (SWR) Branch piece single equal or unequal with access door 75mm bore all as specified and as directed.

S&F in repairs 75 mm bore PVC(SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and as directed.

M&L for 75mm dia PVC (SWR) multi floor trap with grating including jointing with solvent cement complete all as specified and as directed.

S&F PVC (SWR) gully trap 125/110mm, setting and jointing with solvent cement complete all as specified and as directed

Taking up or down steel tubing and connections, fittings etc including cleaning for refixing or removal to store for 15mm bore complete all as specified and as directed.

Taking up or down steel tubing and connections, fittings etc including cleaning for refixing or removal to store for 20mm bore complete all as specified and as directed.

Taking up or down steel tubing and connections, fittings etc including cleaning for refixing or removal to store for 25mm bore complete all as specified and as directed.

S&F GI tube medium grade galvanized (surface/conclead) with all fittings 15mm bore and connections, complete all as specified and as directed.

S&F GI tube medium grade galvanized (surface/conclead) with all fittings 20mm bore and connections, complete all as specified and as directed.

S&F GI tube medium grade galvanized (surface/conclead) with all fittings 25mm bore and connections, complete all as specified and as directed.

Supplying and laying of 16 mm outer dia CPVC pipes SDR 11 & plain CPVC SDR 11 fittings on walls/ceiling (surface/conclead) or laying in floors complete all as specified and as directed.

Supplying and laying of 20 mm outer dia CPVC pipes SDR 11 & plain CPVC SDR 11 fittings on walls/ceiling (surface/conclead) or laying in floors all as specified and as directed.

S&F in repairs 25mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed all as specified and as directed.

S&F in repairs 20mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed all as specified and as directed.

M&L Cutting holes for pipes for a superficial area exceeding 150 Sqcm and not exceeding 400sqcm into or through brick walls built in CM and making good in cement mortar 1:3 or 1:2:4, type B1 all as specified and as directed.

M&L Cutting holes for pipes for a superficial area exceeding 150 Sqcm and not exceeding 400sqcm into or through stone wall built in CM and making good in cement mortar 1:3 or 1:2:4, type B1 all as specified and as directed.

S&F Plastic water closet seat, white, closed pattern with flat bottom and cover and mild steel chromium plated or aluminised hinging device complete all as specified and directed.

S&F in repairs plastic water closet seat, white, closed pattern with flat bottom and cover and mild steel chromium plated or aluminised hinging device suitable as well as for anglo indian WC complete all as specified and directed.

S&F in repairs Vitreous China wash down water closet pan (Pedestal Pattern), EWC White with 'P' or 'S' trap, including provision of fixing bolts and connecting upto drain and flushing pipe etc complete all as specified and as directed.

S&F in repairs vitreous china squatt pattern, Orissa Pattern size 580x440mm White,with integral Foot rests and 'P' or 'S' trap, white, including provision of fixing bolts and connecting upto drain and flushing pipe etc including bedding concrete complete all as specified and as directed.

S&F in repairs PVC Flushing Cistern 10 Ltrs Capacity Syphonic action type with Flush pipe low level, with inlet ball valve,Float chain& pull & brackets, including making necessary connections to water supply pipe line and jointing to WC etc complete all as specified and directed.

S&F in repairs chromium plated brass 15 mm dia health faucet with 8 mm dia. 1.2 m long flexible tube with wall hook, necessary fixing arrangements etc, complete as directed by Engg-in-Carge. Make Jaquar/Cera/Ess Ess or techno commercially equivalent as approved by Engg-in-Charge.

S&F in repairs vitreous China wash basin, white flat back, size 550x400mm including cutting for and pinning in ends of brackets or ereesing stand complete all as specified and directed.

S&F in repairs Brass chromium plated shower rose 125 mm size complete all as specified and directed.

S&F in repairs Brass chromium plated tubular towel rail, 20 mm dia, D type, 60 cm between flanges complete all as specified and directed.

S&F in repairs Stainless steel grating 125mm dia complete all as specified and directed.

S&F PVC waste pipe 32mm size for WHB in repairs complete all as specified and directed.

S&F in repairs PVC waste pipe 40mm size for sink complete all as specified and directed.

S&F in repairs PVC connections 15 mm size with PTMT nuts of length 450mm complete all as specified and directed.

S&F in repairs PVC connections 15 mm size with PTMT nuts of length 600mm complete all as specified and directed.

S&F in repairs 15 mm spindle change in stop cock ( open or concealed) of long and short type without damage to stop cock complete all as specified and directed.

S&F in repairs bib taps cast copper alloy CP fancy type with crutch or butterfly handle screwed down for iron pipe or brass ferrule of 15 mm bore complete all as specified and directed.

S&F in repairs 15mm bore stop valves brass chromium plated, screwed down, high pressure with crutch or butterfly handles screwed both ends for iron pipes complete all as specified and directed.

S&F in repairs 15mm bore stop valves brass (Concealed type) chromium plated with long shank and cup , screwed down, high pressure with crutch or butterfly handles screwed both ends for iron pipes complete all as specified and directed.

S&F in repairs 15 mm bore fancy type chromium plated angle valve cast copper alloy screwed down high pressure screwed both ends for iron pipe or for unions complete all as specified and directed..

S&F in repairs 15 mm bore pillar taps, cast copper alloy, with capstan head, chromium plated, screwed down high pressure with long screwed shanks and flynuts screwed for iron pipes and fixed complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise speciall as specified and directed.

Dismantling cast iron work of any description incl purlins , post rafters etc complete all as specified and directed.

Dismantling plain or corrugated steel sheeting any guage, thickness including roof covering etc complete all as specified and directed.

S&F Mild steel Roof trusses (framed), trussed, purlins,crane gantries, rails and fastnings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. fe-410 (gde E-250) complete all as specified and directed.

S&F Mild steel plates (plain or chequered) channels,distance pieces, cleats etc.square cut or notched including riveted, bolted or welded attachment complete all as specified and directed.

M&L Mild steel Framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and framed and hung as gates, including pintle hinges, stops, hand-made sliding bolts, etc.similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed.

S&F Pre-painted galvalume aluminium zinc coating GI based carrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mps as in roof covering /cladding to wall, fixed with self tapping screws as complete all as specified and directed.

S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick as in ridge of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

Demolition of cement concrete of any description and in any position not otherwise specifically provided all as specified and as directed.

M&L Providing Plain cement concrete type B-0 (1:2:4) using 12.5mm graded stone aggregate as in roof kerbs, padding or mud stops, rounded or chamfered on edges complete all as specified and directed.

M&L for cutting out cracks to V-section in existing roofs or terracing, cleaning out, wetting, grouting with cement and sand slurry (1:3) complete all as specified and directed.

M&L Rendering 10mm thick in cement mortar 1:3 on roof padding finished even and fair with approved water proofing compound @ 200ml per 50kg of cement or as per manufacturer's instruction all as specified and as directed. (Note : WPC shall be measured and paid separately as supply only under relevent item)

Supply only liquid water proofing compound complete all as specified and directed.

M&L Water proofing treatment on horizontal and vertical surfaces with Providing and laying / fixing TPO (Thermoplastic Polyolefin) membraneincl Cleaning the surface and laying of 200GSM Geo textile and cover up with TPO RF 1.2 mm thermoplastic membrane on roof & up to 300 mm of parapets and crumple joint including junction of roof and parapet, welding the seam joints with hot air gun/machine and terminate the corners with extra protection to bear the high wind pressure. The TPO should be thoughroly tightened with the lower structure using mechanical fastening properly to avoid the corners and seam joint failure complete all as specified and directed. Make :Asian paints TPO or equivalent product of M/s Bauchemic/CIPY/SIKA/Pidilite/Dr fixit TO membrane/Berger.

Taking down chowkhats or frames not exc 1.5 sqm with shutter (without taking of shutter from the frames) including taking out hold fasts and PCC bed block complete all as specified and directed.

Supply and fix solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with 19mm x 19mm MS square tube EPDM rubber gasket weather seal to be provided through out the frame, the profile shall be mitre cut at two corners and jointed by inserted 2mm of 150mm long bracket of 15mm x 15mm MS square tube inside the 19mm x 19mm MS square tube and suitable screwed the door frame shall be fixed to the wall using PVC fasteners. A minimum of 6Nos screws to be provided for each frame all as specified and as directed. Note: The quoted rates are deemed to be included for cutting holes, providing concrete for hold fast and making good to the disturbed surfaces.

S&F factory made solid PVC moulded door shutter, with particle board core 28 to 30 mm thick(stiles ) with 2,4 or 6 raised panel design with 2 mm thick moulded PVC sheet on the front face & 2 mm plain colour PVC sheet on back face, fixed in frame at site as per specifications & drawing complete all as specified and directed.

S&F 100mm butt hinges , extruded aluminium alloy with galvanised mild steel hinge pin anodised and fixed, type C-21 complete all as specified and directed.

S&F 150 mm long Aluminium handles, cast type, anodised, complete all as specified and directed.

S&F 150 mm long Aluminium, anodised, barrel tower bolts of extruded section, complete all as specified and directed.

Taking down chowkhats or frames exc. 1.5 sqm and not exc 4 sqm with shutter (without taking of shutter from the frames) including taking out hold fasts and PCC bed block complete all as specified and directed.

S&F Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings complete all as specified and directed. Note : All the aluminium sections provided under this item shall be measured and converted into weight for payment with the designated unit weight mentioned in the manufactures catalouge for the corresponding aluminum sections/fittings.

M&L Granite (of any type) stone slab 16 to 20 mm thick (table rubbed and polished), in skirting, Kitchen platform /dado etc laid over 20mm thick cement screed bed of CM 1:6 jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding the edges half round and polishing including demoltion of old .etc complete including making hole for gas pipe complete all as specified and directed.

M&L Rendering 15mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6 and finished smooth and even without using extra cement complete all as specified and directed.

M&L Rendering 10 mm thick on fair faces of concrete surfaces in ceilings in cement mortar 1:3 and finished fair and even without using extra cement complete all as specified and directed.

M&L Preparing newly plastered surfaces of walls and applying two coats of oil bound distemper using mechanical means over a coat of chalk whitening complete all as specified and directed.

M&L Preparing newly plastered surfaces of ceiling and applying three coats of white wash complete all as specified and directed.

Preparing newly plastered surfaces of walls and applying two coats of cement base paint using mechanical means complete all as specified and directed.

Taking down shutters of any description not exceeding 1 Sq. M each and stacking at site where complete all as specified and directed.

Taking down shutters of any description exceeding 1 Sq. M but not exceeding 2 Sq. M each and stacking at site where directed.

S&F Second class hard wood plain, solid, straight chowkats and frames, wrought, framed, rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed.

S&F Factory made single extruded WPC (wood polymer composite) solid door/window/ceosetory windows and other frame/ chowkhats of size 65x100 mm comprising of virgin PVC polymer of K value 58-60 ( suspension grade) calcium carbonateand natural fibres ( wood powder/rice husk/wheat husk) and non toxic additives ( maximum toxicity index 12 for 100 grms) fabricated with mitred joints after applying PVC solvent cement and screwed with full body thread star headed SS screws having minimum frame density of 750 kg/ cum screw withdrawal strength of 2200 N ( Face)& 1100N (edge) minimum compressive strength of 50 N/mm"2 modulus of elasticity 850 N/mm"2 and resistance spread of flame of class A category with properity of being termite/borer proof,water/moisture proof and fireretardant.WPC to be laminated with foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutters and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk SS screws, complete all as specified and directed. Note:- Stainless steel butt hinges and necessary SS screws shall be paid seperately

S&F Factory made single extruded WPC (wood polymer composite) solid door/window/ceosetory windows and other frame/ chowkhats of size 65x125 mm comprising ofvirgin PVC polymer of K value 58-60 ( suspension grade) calcium carbonateand natural fibres ( wood powder/rice husk/wheat husk) and non toxic additives ( maximum toxicity index 12 for 100 grms) fabricated with mitred joints after applying PVC solvent cement and screwed withfull body thread star headed SS screws having minimum frame density of 750 kg/ cum screw withdrawal strength of 2200 N (Face)& 1100N (edge) minimum compressive strength of 50 N/mm"2 modulus of elasticity 850 N/mm"2 and resistance spread of flame of class A category with properity of being termite/borer proof,water/moisture proof and fireretardant.WPC to be laminated with foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutters and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk SS screws, complete all as specified and directed. Note:- Stainless steel butt hinges and necessary SS screws shall be paid seperately

S&F steel windows with hung shutter including box type hinges with steel hande steel peg stays, and with glazing bars complete all as specified and directed.

S&F steel windows with hung shutter including box type hinges with steel hande steel peg stays, and without glazing bars complete all as specified and directed.

S&F Galvanised mild steel wire cloth, 0.58mm nominal dia of wire and average width of aperture 1.18mm and fixed with aluminium wire staples Ceosetory complete all as specified and directed.

S&F 30 mm thick Second class hard wood Gauzed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc., divided in to squares with plain, chamfered or rounded mitred and rebated sash bars any numbers, edges of framing plain, chamfered or rounded fitted with cut and mitred beads for securing glass, etc, size of members of shutters as specified in SSR Part I, section 8, clause 8.24 (a) supplied and fitted to chowkats

S&F 35 mm thick Second class hard wood Gauzed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc, divided in to squares with plain, chamfered or rounded mitred and rebated sash bars any numbers, edges of framing plain, chamfered or rounded fitted with cut and mitred beads for securing glass, etc, size of members of shutters as specified in SSR Part I, section 8, clause 8.24 (a) supplied and fitted to chowkats complete all as specified and directed.

S&F 35 mm thick factory made flush shutter, solid core construction with block board core and plywood face panels, commercial type on both sides kiln seasoned and chemically pressure treated complete all as specified and as directed.

S&F 35 mm thick Second class hard wood plain framed panelled shutters, (any number of panels) with panels of timber flat on both sides ( feathered edged ) ,or of veneered particle board medium density, wood particle board with commercial face veeners open rebated supplied and fitted to chowkats complete all as specified and directed

M&L Preparation of New or previously untreated wood and wood based surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of Synthetic enamel paint (Ordinary tint) over a coat of Pink primer complete all as specified and directed

M&L Preparing surfaces of wood and wood based materials, steel and iron work new or old, of any description and girth not otherwise described, and treating ends of posts, backs of chowkats, etc area tarred exceeding 0.1 Sq. M and not exceeding 0.5 Sq. M each complete all as specified and directed

S&F 4 mm thick Sheet glass, ordinary quality and glazing with oil putty in squares not exceeding 0.50 Sq. M in each pane complete all as specified and directed.

S&F in repairs 4 mm thick Figured glass, pin headed glass, ordinary quality and glazing with oil putty in squares not exceeding 0.50 Sq. M in each pane including Hacking out old broken glass (any thickness, size, quality or description) from metal frames including punching or drilling out old glazing pins/ spring clips and providing and fixing new ones complete all as specified and directed

S&F in repairs 4 mm thick Sheet glass, ordinary quality and glazing with oil putty in squares not exceeding 0.50 Sq. M in each pane including Hacking out old broken glass (any thickness, size, quality or description) from metal frames including punching or drilling out old glazing pins/ spring clips and providing and fixing new ones complete all as specified and directed.

S&F in repairs Galvanised mild steel wire cloth, 0.58mm nominal dia of wire and average width of aperture 1.18mm and fixed with aluminium wire staples complete all as specified and directed.

S&F 100mm cold rolled mild steel medium weight l butt hinges complete all as specified and directed.

S&F 75 mm medium weight mild steel butt hinges , with galvanised mild steel hinge pin anodised and fixed complete all as specified and directed.

S&F 150 mm long Extruded Aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

S&F 100 mm long Extruded Aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

S&F 100 mm long Aluminium, anodised, barrel tower bolts of extruded section complete all as specified and directed.

S&F 300 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast Aluminium alloy complete all as specified and directed.

M&L Plain Cement Concrete Type B1 1:2:4 (using 20 mm graded granite stone aggregate) in hold fasts and similar works complete all as specified and directed.

S&F Mild steel Angles, bars, flats etc., as in supports for stiffening of fencing, wall ties, hold fasts, clamps and similar small articles confirming to Fe 410 -or Fe 310 complete all as specified and directed.

S&F Fixed in Repairs Vitreous Ware wash down water closet (Pedestal), white (EWC) with seat cover complete all as specified and directed.

Supply and Fix in repairs 10 Litres capacity dual type PVC low level SLIMLINE Flushing Cistern with brackets complete all as specified and directed.

S&F double legged floor door stopper aluminium alloy with rubber etc complete all as specified and as directed

S&F in repairs stainless steel sink,1.0 mm thick for kitchen or laboratorty,with plug,waste pipe,washers including cantilever cast iron brackets,connecting union etc overall size 495 mmx420 mm with bowl size 410 mmx330 mmx160 mm complete all as specified and directed.

S&F in repairs sink with drain board made of stainless steel 1.0 mm thick for kitchen or laboratorty,with plug,waste pipe,washers including bedding in cement mortar to dwarf wall or including fixing cantilever cast iron brackets, and connecting union to pipe etc overall size915x460mmh bowl size 410 mmx330 mmx160 mm complete all as specified and directed.

S&F Ball valves high pressure of PTMT with epoxy coated Aluminium rod and high density plastic ball screwed for iron pipe and fixed for 15 mm complete all as specified and directed.( minimum weight (15 mm-142 gms/20 mm-210 gms/25 mm-455 gms/40 mm-690 gms)

S&F Ball valves high pressure of PTMT with epoxy coated Aluminium rod and high density plastic ball screwed for iron pipe and fixed for 20 mm complete all as specified and directed.( minimum weight (15 mm-142 gms/20 mm-210 gms/25 mm-455 gms/40 mm-690 gms)

S&F Ball valves high pressure of PTMT with epoxy coated Aluminium rod and high density plastic ball screwed for iron pipe and fixed for 25 mm complete all as specified and directed.( minimum weight (15 mm-142 gms/20 mm-210 gms/25 mm-455 gms/40 mm-690 gms)

Removing plants/herbs grown on walls/junctions with roots using herbicide chemical,rendering and making good of existing brick/ concrete surfaces complete all as specified and directed.

S&F in repairs 600mm x 450 mm PVC moulded frame mirror glass, fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified and directed.

S&F in repairs Syphons set for PVC flush cistern complete all as specified and directed.

S&F in repairs waste fittings brass chromium plated with PVC outer cover, 40 mm dia for stainless steel sink complete all as specified and directed.

S&F in repairs waste fittings brass chromium plated with PVC outer cover, 32 mm dia for Wash bashin complete all as specified and directed.

S&F in repairs 20 mm curtain rods of aluminium annodised powder coated fixed in existing brackets complete all as specified and directed.

S&F in repairs curtain rods brackets aluminium annodised powder coated fixed complete all as specified and directed.

S&F in repairs 4 levers Brass Mortice lock, vertical type,of Size 100mm all as specificed in SSR Part-I complete all as specified and directed.

Easing of door / window shutters of any size/ any number of panels for easy closing/ opening / tightening of hinges or changing the position of hinges, adjustment of tower bolts, sliding door bolts etc complete all as specified and directed.

S&F in repairs aluminium handles cast type anodized 125mm complete all as specified and directed.

S&F in repairs aluminium handles cast type anodized 100mm size complete all as specified and directed.

M&L for welding in repairs not exceeding 6 mm thick metal complete all as specified and directed.

S&F in two way bib cock brass chromium plated 15 mm bore complete all as specified and directed.

S&F in repairs 15mm dia Bib tap standard of PTMT any colour high pressure screwed down for iron pipe(Min weight 15mm-90gms) ISI marked all as specified and fixed complete all as specified and directed.

S&F in repairs 15 mm dia. Pillar tap standard of PTMT any colour high pressure screwed down for iron pipe(Min weight 15mm-120 gms) ISI marked all as specified and fixed ccomplete all as specified and directed.

S&F stainless steel plate rack of size 990.60mm x 914.40mm including fixing to wall as directed etc complete all as specified and as directed

S&F 7 feet 4 pipes pulley operated cloths drying system consisting of aluminium pipe of outer dia 22 mm,inner dia 19.80 mm, made up of detrin with rope guide mounted on channel pair of length 24 feet( distance between two pipe is adjustable) locking system to hide rope knot,channel to be mounted or fixed with self taping screws provided in kit.Rope will be HDPE double core of 4 mm dia fixing to ceiling all as specified and as directed

Taking down existing steel window/ventilator shutters area exc 1 sqm and not exc 2 sqm each and carrying out necessary servicing incl welding/greasing/oiling etc for smooth functioning and taking down unserviceable hardwares and refixing with new hardwares and re fixing the window shutters in position all as specified and directed. Note : (i) Windows are to be fixed upto 5 storeys of buildings (ii) Hardwares wherever required to be replaced shall be measured and paid seperately at supply only rates under respective items of this schedule.

Taking down existing steel window/ventilator shutters area n exc 1 sqm each and carrying out necessary servicing incl welding/greasing/oiling etc for smooth functioning and taking down unserviceable hardwares and replacing with new hardwares and re fixing the window shutters in position all as specified and directed. Note : (i) Note : Windows are to be fixed above 4 storey and upto 6 stories of buildings (ii) Hardwares wherever required to be replaced shall be measured and paid seperately at supply only rates under respective items of this schedule.

Supply only mild steel box type hinges, suitable for steel windows complete all as specified and directed.

Supply only mild steel handles , suitable for steel windows fixed with necessary nut, bolt and washers, complete all as specified and directed.

S&F in repairs mild steel peg stays, 300mm long , suitable for steel windows fixed with necessary nut, bolt and washers, fixed in repairs complete all as specified and directed.

Supply only 300mm, ordinary rat rail rod pattern springs including roller and roller plate complete all as specified and directed.

M&L 19mm thick Prelaminated particle board, exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work complete all as specified and directed.

S&F 125mm aluminium anodised Hasp and staple, safety type fixed with screws complete all as specified and as directed complete all as specified and directed.

S&F in repairs Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part IPVC tank 500 lit complete all as specified and directed.

S&F in repairs Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part IPVC tank 1000 lit complete all as specified and directed.

S&F in repairs waste coupling for 75mm/100 mm dia for stainless steel sink complete all as specified and directed.

S&F in repairs PVC/Plastic handle for flushing cistern complete all as specified and directed.

Repairs to tap/pillar tap stop cock any type including changing of of spindle/rubber washer etc if required complete all as specified and directed for the following. Note:( Spindle will be measured separately and paid at supply only rates)

Bib tap

Pillar tap

Stop cock

Concealed stop cock

Supply only brass spindle suitable complete all as specified and directed for the following.

Bib tap

Pillar tap

Stop cock

Concealed stop cock

Removing demolished materials i.e building materials,concrete,stone masonry,debris,tree roots,trunks branches of any size etc to a distance of 30 KM or beyound, out of premises of metropolitan area including loading,unloading by manually or by mechanical means( JCB) and to be transported through tractor-trolly or tipper and stacking at destination as and when complete all as specified and directed.

K V RAJANNA

Kavitha Constructions