Item-2 Annual rate contract for repair and maintenance

Amount

P/Laying P.V.C. / XLPE insulated & P.V.C. sheathed cable of 1.1 KV grade with aluminium conductor of IS:1554 P-I / IS :7098 P - I of Group 1 of approved make in ground as per IS:1255 including excavation of 30cmx75cm size trench, 25 cm thick under layer of sand,IInd class bricks covering, refilling earth,compaction of earth, making necessary connection, testing etc. as required of size.

185.0 Sq.mm 4 core

70.0 Sqmm 4 Core

50.0 Sqmm 4 Core

Replacement of following faulty items/ cnsumable items of DG Sets

Oil Filter of 75/80 KVA DG Sets

Diesel filter of 75/80 KVA DG Sets

Lubricant OIL

180 AH Lead acid battery

coolent

Diesel

Hire charges of Main service line for 3 phase connection upto 50 mtr. Length (without any joint) including meter board, panel/distribution Board and supports with skilled operator to operate system as and when etc as required. (If work contineue for more then one week , rates for next subsequent weeks will be 50% of the original rates.)

upto 25.0 sq.mm PVC insulated and Sheathed cable(Armoured or Un-armoured as required.)

Replacement of existing transformer oil confirming to IS: 335 after removing of old oil and remove from site (old oil shall be retained by the contractor)

Charges for testing of transformer oil for its viscosity and dielectric strength including collection of sample from top and bottom of the existing transformer tank and submission of test report complete with all T & P , labour etc as required .

Charges for collection , Filtration and dehydration of existing transformer oil with the help of high vaccum filtration machine and cleaning of core-coil assembly by hot oil for removal of sludge / dust particles etc. as required.

Supply and filling of fresh transformer oil as per IS: 335 in existing transformer along with submission of oil test report for its physical and chemical properties.The oil shall be clear and free from any suspended matter or sediments complete as required complete in all respect. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR

Repairing of LT/HT bushings of Distribution Transformers includingreplacement of brass studs , porcelain insulators , nut bolts , oil seals , gaskets etc.complete as required complete in all respect. All as per pre approved byEngineer in charge. For additional technical parameters of products/ work refer annexure A

LT Bushing Set

HT Bushing Set

63 KVA to 500 KVA Set

630 KVA to 1600 KVA

Replacement of silica gel Breather of Distribution Transformers of following capacities complete in all respect. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR .

Replacement of gasket of Distribution Transformers of following capacitiescomplete in all respect. All as per pre approved by Engineer in charge. ForFor additional technical parameters of products/ work , refer Annexure "A" attached with this BSR .

63 KVA to 500 KVA Set 1513

630 KVA to 1600 KVA Set

Providing experienced and Highly skilled/skilled/ semi- skilled/Un Skilled labour for electric repair/ maintenanceoperation of Air conditioning/Air cooling/Fire fighting/Lift/DG set/CCTV/EPABX or any other electromechanical systems as per requirement (one shift of 8 Hrs per day for 26 Working Days in a month)

Highly skilled Labour

skilled Labour

Semi skilled Labour

Hire charges for 90-150 Watt LED flood light luminairewith skilled operator to operate system as and when etc as required. (If work contineue for more then one day , rates for next subsequent days will be 50% of the original rates.

With suitable pole

With out pole

Detecting of cable fault for 33KV and 11 KV cable with fault locate Machine

Providing & Fixing of IK07 IP-66 protected high power LED flood light system with Pressure diecast aluminium housing LM6/ ADC12 material , toughened glass diffuser with suitable lenses on LED to achieve various beam angles, 240 volt, 50Hz, of high power LED lamps . Integrated driver must be potted & has a unique BIS R number shall be high efficiency having efficiency more than 85 % and in compliance to BIS certified and T.C. certificate. The System level Luminaire efficacy >=120 lm/ wt with High Power LEDs is to be used . LED driver Input Voltage AC 120 to 270 V AC with High voltage Cutoff @>=300 V AC andAuto resetting Safety . Input Frequency 50Hz±3%, Power Factor >0.95,driver Efficiency >85% , THD(I) <10% , driver current <1000mA shown in LM79 report. driver should be Phase to phase protection of 440 V for 4 Hrs. Electrical Connector Must be provided, Surge Protection Min >=4KV internal and 10KV external, System life of 30000 Burning hours with 70% of Initial Lumens maintained, color Rendering Index >70 and CCT 5700K ±355K. Driver current <1000mA shown in LM79 report. Manufactures Word Mark/Name Engraved/Embossing/Screen printing on die cast housing to allow traceability/authenticity. Fixture shall be IS 10322 Complianced. OEM Must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79/LM80) Certificate/ report with liable warranty of product/accessories from OEM shall be submitted. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR

High Power LED Flood Light 150W

High Power LED Flood Light 200W

Providing & Fixing of IK07 IP-66 protected high power LED flood light system with Pressure diecast aluminium housing LM6/ ADC12 material , toughened glass diffuser with suitable lenses on LED to achieve various beam angles, 240 volt, 50Hz, of high power LED lamps . Integrated driver must be potted & has a unique BIS R number shall be high efficiency having efficiency more than 85 % and in compliance to BIS certified and T.C. certificate. The System level Luminaire efficacy >=120 lm/ wt with High Power LEDs is to be used . LED driver Input Voltage AC 120 to 270 V AC with High voltage Cutoff @>=300 V AC and Auto resetting Safety . Input Frequency 50Hz±3%, Power Factor >0.95 ,driver Efficiency >85% , THD(I) <10% , driver current <1000mA shown in LM79 report. driver should be Phase to phase protection of 440 V for 4 Hrs. Electrical Connector Must be provided, Surge Protection Min >=4KV internal and 10KV external, System life of 30000 Burning hours with 70% of Initial Lumens maintained, color Rendering Index >70 and CCT 5700K ±355K. Driver current <1000mA shown in LM79 report. Manufactures Word Mark/Name Engraved/Embossing/Screen printing on die cast housing to allow traceability/authenticity. Fixture shall be IS 10322 Complianced. OEM Must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79/LM80) Certificate/ report with liable warranty of product/accessories from OEM shall be submitted. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR

LED Street Light fixture 30 Watt

LED Street Light fixture 70 Watt

LED Street Light fixture 120 watts

B-check servicing of 75/80/320 KVA DG set at Site i/c supply & replacing of mobile oil (Koel Care Super Genuine ) for B-check servicing as per manufacturer's recommendation (servicing is to be carried out through authorised dealer only).

Dimension : Ø123*128 500mm, Wattage : 6W LED. Supply of 230- 240Vac CRI >80 6W Height 500mm Light Distribution 175° Having 3000K ,Electronic driver ON/OFF CE and BIS LUMINAIRE TYPE Bollard. IP rating IP65 MATERIAL CHARACTERISTICS Extruded aluminium bottom pipe (grade 6063 with test certificate) aluminium top cover. Pre treated silicone gaskets. Die-cast aluminium mounting plate Ø123*128 x 500mm Height pure polyester powder coating. LB074 Bollard This luminaire contains built- in LED modules. LED modules are engineered accordingly to the existing regulations of Lumen Maintenance (LM80) and Technical Memorandum (TM21), Lifespan of the luminaire > 60,000 hours at 40°C. Operating ambient temperature range is from - 15°C to +50°C. Driver efficiency >87%, power factor >0.95, THD<8.2%, Surge protection 3 KV.

Circular Lighting Pole - Ø114 Series, : Ht.5000 : Supply of 5000mm Circular pole made of circular mild steel pipe (grade YST 210) 114.3mm Dia x 3.2mm thick with 4988mm Height. Wind speed considered in design 50 m/sec in compliance with IS 875 Part 3 : 1987. Pole section welded by certified welders using high end MIG welding processes. PDC aluminium service door 348mm height x 106mm width shall be provided with the company logo embossed on the bottom of the door and safety rope with IP protection rating. The control gear tray is prewired with 2.5 Sq.mm cable, 6A MCB and 32A terminal connectors for loop-in / loop-out arrangement. Any other internal cables and connections shall not be covered in the scope of supply. Mild steel mounting plate 250mm Square x 12mm thick Steel of grade E250 to IS 2062 : 2011 with 4 elongated holes 38 x 19 to suit M16 x 500mm bolts of grade 4.6 at CC180. This mounting steel plate along with foundation bolts of suitable size to be used for ensuring firm grouting into the specially designed foundation. All dimension and weight are within +/- 5% tolerance. The pole is coated with pure polyester powder coating or epoxy zinc phosphate primer and finished using environmentally stable polyurethane based paint (coating thickness 60-80 microns). The Pole shall be provided with Graphite grey / Anthracite grey / Black as standard colour options.

Juno, Dimension : Ø600 x 422, Wattage : 60W LED. : Supply of Juno ID : 5040 LED 3000K, 4000K, 5700K 230-240Vac CRI >80 MacAdam step 3 Input power : 60W Dimension : Ø600 x 422 mm Light Distribution 360° Electronic driver ON/OFF CE and BIS LUMINAIRE TYPE Light Column. IP rating IP65 MATERIAL CHARACTERISTICS Spun aluminium top cover Ø600 x 1.6mm thickness & LED fixing bottom cover. Mild steel rectangle hotdip galvanized supporting arm integrated with Mild steel hotdip pipe Ø102 x 240mm height. Diffuser placed into the provision formed on the pheriphery of the bottom cover. Pressure die cast base (grade ADC12 with test certificate) suitable for Ø60mm OD pipe. SS fasteners. Pure polyester powder coated process : Acid treatment & pure polyester powder coating. LIGHTING PERFORMANCE Translucent acrylic diffuser of 1.8mm thickness with controlled downward light emission. Lamp fixed position. JUNO This luminaire contains built-in LED modules. LED modules are engineered accordingly to the existing regulations of Lumen Maintenance (LM80) and Technical Memorandum (TM21), Lifespan of the luminaire > 60,000 hours at 40°C. Operating ambient temperature range is from -15°C to +50°C. Driver efficiency >85%, power factor >0.9, THD <10%, Surge protection 6KV.

Supply, Installation testing and Commmisioning of lighting pole having LED 3000K, 4000K, 5700K as per architectural theme and approval 230-240Vac CRI >80 MacAdam step 3 Input power : 36W Height 2400mm Light Distribution 360° Electronic driver ON/OFF CE and BIS LUMINAIRE TYPE Supply, Installation testing and Commmisioning of lighting pole having LED 3000K, 4000K, 5700K as per architectural theme and approval 230-240Vac CRI >80 MacAdam step 3 Input power : 36W Height 2400mm Light Distribution 360° Electronic driver ON/OFF CE and BIS LUMINAIRE TYPE Light Column. IP rating IP65 MATERIAL CHARACTERISTICS Extruded aluminium bottom pipe (grade 6063 with test certificate) Ø100 x 2.5mm thickness, Mild steel rectangle tube 25 x 12 x 2mm thickness, spun aluminium top cover. Diffuser placed into the provision formed on the pheriphery of the bottom cover. SS fasteners. PDC aluminium service door 348mm height x 81mm width at 244mm height above the base plate shall be provided with the company logo embossed on the bottom of the door and safety rope. The control gear tray to be prewired with 2.5 Sq.mm cable, 6A MCB and 32A terminal connectors for loop-in / loop-out arrangement. MS mounting plate Sq.200 x 12mm thick steel of gradeE250 to IS 2062:2011 with 4 elongated holes 38 x 19 to suit M16 bolts at CC140. This mounting steel plate along with foundation bolts of suitable size to be used for ensuring firm grouting into the specially designed foundation pole. Hot dip galvanised foundation bolt. Mechanical resistance IK08. Pure polyester powder coated process : Mild shot blast & pure polyester powder coating. LIGHTING PERFORMANCE Translucent acrylic diffuser of 1.8mm thickness with controlled downward light emission. Lamp fixed position. This luminaire contains built-in LED modules. LED modules are engineered accordingly to the existing regulations of Lumen Maintenance (LM80) and Technical Memorandum (TM21), Lifespan of the luminaire > 60,000 hours at 40°C. Operating ambient temperature range is from -15°C to +50°C. Driver efficiency >85%, power factor >0.95, THD <10%, Surge protection 4KV. Final Design to be approved by the Architect Make : K-Lite / Ligman / Neri or equivalent

Bidder Name

Amount

ASHISH ELECTRICALS(GSTN-08AHXPC7032J1ZZ)