REPAIR REPLACEMENT OF PLUMBING ITEMS, REPAIR TO WINDOW ALUMINIUM DOOR REPAIR TO FLOORING FLOAT VALVE AND TANK CLEANING IN OTM MD ACCN OF AGE BRII UNDER GE NARANGI

Amount

Taking down cement plaster on brick or stone walls etc including racking out joints, hacking for key, scrubbing down with water etc. complete all as specified and as directed.

Material and labour for rendering 15mm thick internal in cement mortar 1:6 on fair faces of brick/concrete surfces finished even and smooth without using extra cement complete all as specified and as directed

Material and labour for 15mm thick rendering in cement mortar 1:4, in two layers, under coat of 10 mm thick and top of 5 mm thick, to fair faces of brick or concrete wall surfaces, top layer 5 mm thick mixed with water proofing compound @ 200ml/50Kg by weight of cement or as per manufacture's instructions, finished even and smooth without using extra cement complete all as specified and as directed. Note : Water proofing compound shall be measured and paid separately as "Supply only.

Supply only liquid integral water proofing compound (IS2645:2003) complete all as specified and directed.

Material and labour for rendering 5 mm thick in cement mortar (1:3) as in ceiling finished even and smooth without using extra cement complete all as specified and directed

Material and labour for preparation of newly plastered surface of ceiling and applying three coats of white wash complete all as specified and as directed.

Material and labour for preparation of newly plastered surface of wall and applying two coats of acrycil distemper over a coat of primer complete all as specified and directed.

Material and labour for preparation of newly plastered surfaces of wall and applying two coats of cement base paint over a coat of primer complete all as specified and directed.

Dismantling floor, hearth and wall tiling including cement mortar bedding (but excluding backing), removing rubbish off the premises complete all as directed.

Material and labour for coloured Non-skid ceramic tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.18 Sqm but not exceeding 0.38 Sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match existing surfaces over and including 15mm thick screed bed in cement mortar (1:4) complete all as specified and as directed.

Material and labour for coloured Non-skid ceramic tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.18 Sqm but not exceeding 0.38 Sqm as in skirting/dado etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match existing surfaces over and including 10mm thick rendering in cement mortar (1:4) complete all as specified and as directed.

Material and labour for colured Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, as in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match existing surfaces over and including 15mm thick screed bed in cement mortar (1:4) complete all as specified and as directed.

Material and labour for glazed ceramic tiles (Coloured) 450x350x7 mm thick on vertical surfaces such as skirting, dados and riser to steps etc. set and jointed in neat cement slurry and pointed in coloured cement to match Including 10 mm thick rendering cement mortar 1:4 complete all as specified and as directed.

Material and labour for glazed vitrified tiles (GVT), light shade, 10mm thick (square/rectangular) area of each tile not exceeding 0.36 sqm, laid in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match colour of tiles, over and including 15mm thick screed bed in cement mortar 1:4 complete all as specified and as directed.

Material and labour for 10mm thick glazed vitrified tiles (GVT) light shade area of each tile n exc 0.36sqm as in vertical surfaces such as skirting/dados etc etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tile over and including 10 mm thick rendering in cement mortar 1:4 complete all as specified and as directed.

Taking down chowkats with shutters including builders hardware(without taking off shutters from the frame) area n.exc. 1.5 Sqm each complete all as specified and as directed.

Taking down chowkats or frames area exceeding 1.5 Sqm but not exceeding 4 Sqm each including shutter with builders hardware (without taking off shutters from the frame) complete all as specified and as directed.

Taking down shutters of any description exc 1 Sqm but not exc. 2 Sqm each including removing from site complete all as specified and directed.

Supply and fix PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube complete all as specified and as directed.

Supply and fixing factory made solid panel PVC door shutter 30mm thick (stile) consisting of frame made out of MS tube for top and bottom rails, MS frames shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stills and plain colour PVC sheet top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail, paneling of plain colour PVC sheet to be fitted in the MS frame welded/ scaled to the stiles and rails with suitable PVC sheet beading and jointed together with solvent cement as per drawings and specifications as catered in SSR Part – II 2004

Supply and fixing 30 mm thick flush shutter, solid core construction with particle board core and plywood face panel, commercial type on both side complete all as specified and as directed

Supply and fixing 35mm thick second class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauge etc (with out sash bar), edges of framing with plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc, sizes of members of shutters all as specified in SSR part-I section 8 clause 8.24 (a) complete all as specified and as directed

Supply and fix aluminium butt hinges meium weight of size 100 mm etc complete all as specified and directed.

Supply and fixing 150mm long aluminium anodised barrel tower bolts of extruded section complete all as specified and as directed

Supply and fixing 150mm in size extruded aluminium handles, fabricated type, anodised complete all as specified and as directed

Supply and fixing aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolt of extruded section or cast aluminium alloy and fixed 300mm long complete all as specified and as directed

Supply and fix in repair aluminium door closer (Diecast) body hydraulically regulated, designation No.3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and complete all as directed.

Supply and fixing strainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or galvanized wire staples complete all as specified and as directed

Supply and fix in repair double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed complete all as specified and as directed

Anodized aluminium sliding glazed window shutter (double leaf glazed shutter and single leaf mosquito proof shutter each in single frame work) without sash bars with anodized aluminium shutter of section 40.00mmx20.00mmx1.10mm thick and window chowkat of section 92.00mmx29.50mmx1.20mm thick including necessary jointing cleats, glazing clips, rubber packing, snap beading, screws, handle, tower bolts and locking arrangement etc. and including 4mm thick sheet glass, tinted quality on panel and stainless steel wirecloth or aluminium anodized wire cloth for mosquito proofing, 0.45mm nominal dia and average width of aperture 1.40mm fixed with aluminium screws and tacks and making good to disturbed surfaces complete all as specified and as directed.

Supply and fix steel windows with side hung shutters glazed shutter incl both side openable (out side glazed window and inside fly proof window) including projecting type hinges with steel handle and steel peg stay complete with glazing bars and 12mm square bar or round bar of approved design welded to steel window frame dovetailed or welded complete all as specified and directed . Note: Guard bar or square bar shall be measure and paid separately.

Anodized aluminium push pull type fully glazed door shutter (single leaf / double leaf) having top rail of section 85.00mmx44.45mmx2.00mm, bottom rail of section 85.00mmx44.45mmx2.00mm thick, door verticals of section 44.45mmx44.45mmx2.00mm thick and lock rail of section 85.00mmx44.45mmx2.00mm thick with aluminium anodized chowkats of section 63.50mmx33.10mmx2.50mm thick including necessary jointing cleats, glazing clips, rubber packing, snap beading, screws, handle and locking arrangement etc. 5.5 mm thick float glass tinted quality on top/bottom panel complete all as specified and as directed. (Note : Door closer shall be measured and paid separately)

Hacking out old broken glass (any thickness, quality or description) from wooden/steel frame or stone concrete or brick surrounds, glazed with putty or fixed with beads complete all as specified and as directed.

Supply and fix 3 mm thick figured glass pin head type and glazing with oil putty in squares not exc 0.5 sqm in each pane complete all as specified and directed

Supply and fix 5.5 mm thick sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane complete all as specified and directed.

Taking down rolling shutter of any type and repairs to defective components/replacement such as rolling system and pulling system, re-assembling the whole rolling shutter including greasing complete, welding, drilling where required and refixing the shutter in the same opening complete area of each shutter n. exc 10 sqm all as directed. All the shutter shall be removed carefully with accessories without damaging the adjacent structures. Contractor shall lay out all the defective parts of removed shutter at site and after verification by Engr-in-charge, defective parts shall be replaced with new fitting/items, these fixtures/items/parts shall be paid extra at supply only rates. All the repairs parts/accessories, along with new parts/accessories shall be reassmebled and fixed to the satisfaction of Engr-in-charge in existing postion. (Note:Contractor shall carry out necessary greasing, easing etc for functioning of the shutter, without any extra cost to the department.)

Taking down rolling shutter of any type and repairs to defective components/replacement such as rolling system and pulling system, re-assembling the whole rolling shutter including greasing complete, welding, drilling where required and refixing the shutter in the same opening complete area of each shutter exc 10 sqm but not exc 20 sqm each all as directed. All the shutter shall be removed carefully with accessories without damaging the adjacent structures. Contractor shall lay out all the defective parts of removed shutter at site and after verification by Engr-in-charge, defective parts shall be replaced with new fitting/items, these fixtures/items/parts shall be paid extra at supply only rates. All the repairs parts/accessories, along with new parts/accessories shall be reassmebled and fixed to the satisfaction of Engr-in-charge in existing postion. (Note:Contractor shall carry out necessary greasing, easing etc for functioning of the shutter, without any extra cost to the department.)

Taking down rolling shutter of any type and repairs to defective components/replacement such as rolling system and pulling system, re-assembling the whole rolling shutter including greasing complete, welding, drilling where required and refixing the shutter in the same opening complete area of each shutter exc 20 sqm but not exc 50 sqm each all as directed. All the shutter shall be removed carefully with accessories without damaging the adjacent structures. Contractor shall lay out all the defective parts of removed shutter at site and after verification by Engr-in-charge, defective parts shall be replaced with new fitting/items, these fixtures/items/parts shall be paid extra at supply only rates. All the repairs parts/accessories, along with new parts/accessories shall be reassmebled and fixed to the satisfaction of Engr-in-charge in existing postion. (Note:Contractor shall carry out necessary greasing, easing etc for functioning of the shutter, without any extra cost to the department.)

Taking down sliding shutter of any type and repairs to defective components/replacement such as sliding system and pulling system, re-assembling the whole sliding shutter including greasing complete, welding, drilling where required and refixing the shutter in the same opening complete area of each shutter exc 10 sqm but not exc 20 sqm each all as directed. All the shutter shall be removed carefully with accessories without damaging the adjacent structures. Contractor shall lay out all the defective parts of removed shutter at site and after verification by Engr-in-charge, defective parts shall be replaced with new fitting/items, these fixtures/items/parts shall be paid extra at supply only rates. All the repairs parts/accessories, along with new parts/accessories shall be reassmebled and fixed to the satisfaction of Engr-in-charge in existing postion. (Note:Contractor shall carry out necessary greasing, easing etc for functioning of the shutter, without any extra cost to the department.)

Supply only 100 mm dia 450 mm long SWG 'O' high tensile spring thickness not less than 6 mm of size conforming to relevent IS all as specified and as directed.

Supply only roller of steel pipe (shaft) confirming to heavy duty of size 50 mm nominal bore all as specified and as directed.

Supply only ball bearing of No 6213/6214 complete all as specified and as directed.

Supply only locking plate made of 3.15 mm thick reinforced with mild steel angle section not less than 35 x 35 x 5 mm size bottom complete all as specified and as directed.

Supply only guide channel made of mild steel deep channel section not less than 3.15 mm thick depth of channel 75 mm complete all as specified and as directed.

Supply only mild steel clip suitable for riveting to lath curtain complete all as specified and as directed.

Supply only lath section 1.20 mm thick for shutter width exc 35 m conforming to IS-6248-1979 (section of lath shall have a distance of 75 mm between rolling center) complete all as specified and as directed.

Supply only MS sheet 1.00 mm thick as in hood cover complete all as specified and as directed.

Supply only bevel gear box and crank handle assembly complete all as specified and as directed.

Supply only MS wheel of size 100x50mm in top rail complete all as specified and as directed.

Supply only MS wheel of size 50 x 25 mm in bottom rail complete all as specified and as directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed

Supply and fix mild steel framed work such as grills, gratings, angle iron, mild steel sheets, mild steel round bar, MS flat iron etc.. for chowkhats or doors shutters or windows etc with ends of bars shouldered and/or riveted, wlded or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165 complete all as specified and as directed.

Material and labour for preparation of new or previously untreated surfaces of steel and steel based surfaces of any description, not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide, zinc chrome primer complete all as specified and directed.

Materials and labour for preparation of new or previously untreated surfaces of wood and wood based surfaces of any description, not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed

Taking up or down existing GI water tubing complete with all fittings of 15 mm bore complete all as specified and directed.

Supply and fix GI tubing medium grade with all fittings like Tee, bend, elbow etc, 15 mm bore fixed to walls or ceilings with saddles/spacers complete all as specified and directed.

Taking up or down existing GI water tubing complete with all fittings of 20 mm bore complete all as specified and directed.

Supply and fix GI tubing medium grade with all fittings like Tee, bend, elbow etc, 20 mm bore fixed to walls or ceilings with saddles/spacers complete all as specified and directed

Supply and fix in repairs bib taps 15mm dia, cast copper alloy, chromium plated, fancy type with crutch or butter-fly handles screwed down for iron pipe or for brass ferrule complete all as specified and directed.

Supply and fix in repairs10 Litres capacity, PVC valveless syphonic action type, flushing cistern, low level, white or coloured, with inlet, ball valve, float and handle including brackets etc complete all as specified and as directed

Supply and fix in repairs vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) complete including provision of lime concrete bedding complete all as specified and as directed

Supply and fix in repair vitreous china wash down water closet (EWC) size 540x365x390mm pan (pedestal pattern) white, including seat cover, closed pattern with flat bottom and cover with chromium plated hinging device complete all as specified and directed.

Supply and fix in repairs vitreous China wash basin, white, flat back , size 550 x400mm excluding taps, waste, chain and plug and porcelain stopper but including brackets complete all as specified and directed.

Supply and fix in repair 15mm bore pillar taps cast copper alloy with capstan heads chromium plated screwed down high pressure with or without lettered 'HOT' or 'COLD' with long screwed shanks and fly nuts screwed for iron pipe and fixed complete all as directed.

Supply and fix in repairs 20 mm dia ball brass valves high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed complete all as specified and directed.

Supply and fix in repairs stop valves 15 mm dia cast copper alloy, fancy type chromium plated, screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or unions complete all as specified and directed.

Supply and fix in repairs 32 dia and 90 cm long PVC solid waste pipe complete all as specified and directed

Supply and fix in repairs 40mm dia and 90 cm long PVC waste pipe complete all as specified and directed

Supply and fix PTMT waste coupling of 32mm dia,(half or full thread) inclduing taking down old coupling of any discription complete all as specified and as directed

Supply and fix PTMT waste coupling of 40mm dia,(half or full thread) inclduing taking down old coupling of any discription complete all as specified and as directed

Supply and fix in repair PVC connections pipe 15mm size with PTMT nuts of length 450mm complete all as specified and as directed

Supply and fix in repair angle valve 15mm bore (dia), cast copper alloy,chromium plated, fancy type including flange, screwed down, high pressure, screwed both ends for Iron pipe complete all as specified and as directed.

Supply and fix in repairs chromium plated soap dish fixed to plugs with chromium plated brass screws complete all as specified and as directed

Supply and fix in repairs chromium plated tubular towel rail 20mm dia, D type, 60 cm long between flanges including necessary aluminium brackets complete all as specified and as directed

Supply and fix in repairs chromium plated tubular towel ring complete all as specified and as directed

Supply and fix in repairs 125mm chromium plated shower roses with or without swivel joints, any size, including fixing to steel pipe or union complete all as specified and as directed

Supply and fix in repair PVC bathroom mirror cabinet with 4 mm thick looking glass mirror of overall size 400x500 mm of approved colour and pattern all as specified and directed

Supply and fix in repair bath wall mixer with 15mm bore (dia) spout, chromium plated with long bend pipe for over head shower including flanges complete all as specified and as directed.

Supply and fix in repair rotational moulded polyethylene water storage tank 500 litre capacity of triple layered layer wall construction (Cylindrical, vertical with closed top) hoisted and fixed in position including 20 mm dia ball brass valves, high pressure with polythene float and fly nut complete screwed for iron pipe or brass ferrule complete all as specified and as directed.

Supply and fix in repair rotational moulded polyethylene water storage tank 1000 litre capacity of triple layered layer wall construction (Cylindrical, vertical with closed top) hoisted and fixed in position including 20 mm dia ball brass valves, high pressure with polythene float and fly nut complete screwed for iron pipe or brass ferrule complete all as specified and as directed.

Supply and fix in repairs Vitreous China urinal, half stall white (excluding flushing cisterrn) including urinal spreader, PVC connection, 40mm PVC waste pipe & 40mm waste coupling providing and fixing plugs, bedding urinal against wall in mortar 1:2, securing urinal to plug, with and including 60mm long screws, pointing around urinal back in cement, fixing flush pipe, grating and union for discharge pipe complete all as specified and as directed.

Cleaning and removing all scale and dirt etc from tanks and from mouths of circulating pipes etc of capacity exc 500 ltrs but not exc 1000 litrs complete all as specified and as directed.

Supply and fix in repair 110mm dia bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls complete all as specified and as directed.

Supply and fix in repair 75mm dia bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls complete all as specified and as directed.

Supply and fix in repair 110mm dia bore PVC (SWR) bends any radius complete all as specified and as directed.

Supply and fix stack clamps out of 50 mm by 5 mm flat iron and 16 mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof for 110mm dia bore of pipe complete all as specified and as directed.

Supply and fix stack clamps out of 50 mm by 5 mm flat iron and 16 mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof for 75mm dia bore of pipe complete all as specified and as directed.

Supply and fix in repairs grating doom 100 mm dia of PTMT ( Min wight 25 gms) complete all as specified and as directed.

Supply and fix in repairs grating doom 125 mm dia of PTMT ( Min wight 40 gms) complete all as specified and as directed.

Supply and fix in repairs glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and as directed.

Supply and fix in repairs corner glass shelf of size 300 mm with chromium plated bracket guard and railing, complete all as specified and as directed.

M/s DAS AND CO (BID ID -3356172)

M/s Talukdar Construction (BID ID -3357335)

M/S Bharat Construction (BID ID -3356111)

KAKWANI BUILDERS (BID ID -3357109)

PK ENGINEERING (BID ID -3356289)

M/S M Ahmed and Co. (BID ID -3356080)

VENUS TRADING CORPORATION (BID ID -3357174)

PARAS ENTERPRISE (BID ID -3355800)