SPECIAL REPAIRS TO BLDG NO MSQ 42, SPECIAL REPAIRS TO MANHOLE AND SEWAGE LINES AT CASTLE, OLD NEW NEELAMBER, SPECIAL REPAIRS TO APPROACHES NEAR CASTLE 13 TO 18, WH 15 TO 17, WH 21 TO 24, WH 67 TO 70, WH 73 TO 74 AND CERTAIN MINOR / REVENUE WORKS AT

Amount

B/R PORTION Demolition of brick work or stone / boulder masonry, built in cement mortar, including all quoins, arches, pillars etc but excluding ashlar facing, dressed stone work and precast concrete articles etc., and removing unserviceable debris off the premises complete all as specified and directed by Engr-in-Charge.

Demolition of cement concrete (unreinforced) in ground floor and in pavings n.exc 15 cm thickness (below or above ground level) and removing debris off the premises complete all as specified and as directed.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for, and removing debris off the premises all as specified and as directed.

Dismantling timber scantlings 40 Sqcm and over in section in any position framed or unframed work etc, complete all as specified and as directed.

Dismantling timber as in fillets, rails, posts, rafters, purlins etc in framed /unframed work, n.exc 40 Sqcm in section in any position, complete all as specified and as directed.

Dismantling Asbestos cement (corrugated, semicorrugated etc.,) sheets in roof, complete all as specified and as directed.

Taking down chowkats or frames including shutters (without taking off shutters from the frames) n.exc 1.50 Sqm each, and removing from site, complete all as specified and as directed.

Taking down chowkats or frames including shutters (without taking off shutters from the frames) exc 1.50 Sqm and n.exc 4 Sqm each, and removing from site, complete all as specified and as directed.

Excavation in trenches n.exc 1.50 m wide and n.exc 1.50m in depth in foundation and getting out in hard/dense soil all as specified and as directed.

M & L for providing plain cement concrete (1:4:8) type D-2, (using 40mm graded stone aggregate) as in foundations, filling, mass concrete all as specified and as directed.

Returning filling in including spreading leveling watering and well ramming in layers not exc 25 cm with excavated soil all as specified and as directed.

Removing excavated material (soil) to a distance n.exc 50m and depositing where directed at a level n.exc 1.50m above the starting point complete all as specified and as directed.

M & L for reinforced cement concrete (1:2:4) (Nominal mix), type B-1 (using 20mm graded crushed stone aggregate) as in slab supported on walls, beams and columns in floors, roofs, landings, shelves etc complete all as specified and directed by Engr-in-Charge.

M & L for Plain cement concrete (1:3:6) (Nominal Mix) type C-1 (using 20 mm graded crushed stone aggregate) as in surface channels or drains etc, complete all as specified and as directed.

Extra labour for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred / stopped ends etc, complete, all as specified and as directed.

M & L for walling of random rubble, uncoursed, well bonded, bedded and solidly hearted built in CM (1:4) including necessary bond stones and pointing the unaccessible dressed surface with same mortar as the work proceeds all as specified and as directed.

M & L for half brick thick brick wall with subclass 'B' bricks straight or curved on plan to any radius built in CM (1:4) all as specified and as directed.

Dismantling of floor hearth or wall tiling including cement mortar bedding (but not backing) removing serviciable tiles to store and rubbish off the premises all as specified and as directed.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust etc., complete all as specified and as directed.

M & L for 40mm thick PCC (1:2:4) type B-1, (using 20mm graded crushed stone aggregate) as in flooring, finished even and smooth without using extra cement all as specified and as directed.

M & L for glazed ceramic coloured tiles 300 mm x 200 mm x 7 mm thick as in vertical surfaces such as skirting, dado etc., set and jointed in neat cement slurry, pointed in white or coloured cement to match, laid over and including 10 mm thick screed bed in CM (1:4) to receive tiles, complete all as specified and as directed.

M & L for Non skid ceramic coloured tiles 7 to 8 mm thick (square / rectangular) area of each tile exc 0.06 Sqm but n exc 0.12 Sqm, in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and including 15 mm thick screed bed or bedding layer in CM (1:4) all as specified and directed.

M & L for use and waste of timber as in form work to sides and soffits of suspended slab such as roof slab, floor slab, shelves and similar works, finishing rought the concrete surfaces flat complete all as specified and as directed.

M & L for mild steel TMT bars 6mm to 8mm dia in reinforcement, cut to length, bent to shape required including cranking, bending spirally or hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia complete all as specified and as directed.

S & F for mild steel roof trusses(framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (beam, tee, angle, channel or flat section) including distance pieces, cleats etc., conforming to Fe 290 (Gde E-165) complete all as specified and directed by Engr-in-Charge.

S & F second class hard wood (Sal / Hollock) glazed and skeleton shutters 35 mm thick, open rebated and prepared to receive glass or gauge,etc., (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut & mitred beads for securing gauge, sizes of members of shutters as specified in SSR Part-I Section-8, clause 8.24 (a) for door shutter, supplying and fitted to chowkats, complete all as specified and as directed.

S & F second class hard wood plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face venneers: supplied, 35 mm thick, sizes of members of shutters as specified in SSR Part I, Section-8, clause 8.24 (a) for door shutters, fitted to chowkats, complete all as specified and as directed.

S & F Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC ' C' channel having a PVC sheet strip of 20 mm width struck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rails and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to in stiles & rails with suitable PVC sheet beading and jointed together with solvent cement supplying & fixing in frames at site as per specification and drawing shown in SSR Part -II, complete all as specified and as directed.

S & F Solid PVC door frame of size 50 mm x 47 mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, supply & fixing in opening as per specification & drawing shown in SSR Part-II, complete all as specified and as directed.

S & F Aluminium, anodised, barrel tower bolts of extruded section, 200mm long, complete all as specified and as directed.

S & F 300 mm size aluminium alloy anodised sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy, complete all as specified and as directed.

S & F mild steel cold rolled Butt hinges, medium weight, 100 mm long, complete all as specfied and as directed.

S & F aluminium handles, cast type, anodised of size 150 mm long, complete all as specified and as directed.

S & F Tubular towel rail, 20 mm dia, 60 cm long, chromium plated with a pair of brackets, fixed to wall with CP brass screw and PVC rawl plugs complete all as specified and as directed.

S & F galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks or galvanised wire staples, complete all as specified and as directed.

S & F steel windows hollow section (double leaf, gauge and glazed) with side hung shutters including projecting type hinges with steel handle and steel peg stay, complete with glazing bars dove tailed or welded, complete all as specified and as directed.

S & F pressed steel frames of size 125 x 60 mm using 1.25mm thick sheets for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc and providing one shop coat of primer and taring back side of frame, complete all as specified and as directed.

M & L for PCC (1:2:4), type B-0 (using 12.5mm graded stone aggregate) as in filling of steel chowkats or frames complete all as specified and as directed.

S & F mild steel framed work such as grills, gratings, guard bars etc., and similar works conforming to Fe-290 Gde-E 165 complete all as specified and directed.

S & F galvanised, corrugated mild steel sheeting 0.60mm thick with two corrugations side lap, in roof, walls etc with grade of zinc coating 275 and fixed with L type or J type or cranked hook bolts in lieu of screws all as specified and as directed.

S & F plain , galvanished, mild steel sheeting 0.60mm thick, in ridges, hip, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 275 all as specified and as directed.

M & L for second class hardwood clean sawn battens at 25 cm centres exc 5 Sqcm & n exc 15 Sqcm all as specified and as directed.

M & L for second class hardwood plain fillets square, rectangular or traingular in section, clean sawn, secured with nails or brads exc 13 Sqcm and n.exc 25 Sqcm all as specified and as directed.

M & L for roof tiles, Mangalore pattern, interlocking at side joints, laid dry all as specified and as directed.

M & L for ridge or hip tiles to suit mangalore pattern of roofing tiles, bedded and jointed in lime mortar (1 :3) or cement mortar (1:6) all as speciifed and as directed.

M & L for 75 mm thick cement concrete (1:3:6) type C-2 (using 40mm graded stone aggregate) as in plinth protection, sub floors, sub base, pavings, floors etc., finished fair & even or finished even and smooth without using extra cement, complete all as specified and as directed.

Taking down cement plaster, any description, on brick or stone walls, etc. including raking out joints hacking for key, scrubbing down with water etc., and removing debris off the premises all as specified and directed.

M & L for rendering 15 mm thick in CM (1:6), on stone masonry surfaces or other than fair face of brick work or on one side lathing and finishing the surface even and smooth without using extra cement all as specified and as directed.

M & L for raised pointing in cement mortar (1:4) to random or polygonal rubble, uncoursed or brought upto courses including raking out joints to existing or new surfaces complete all as specified and as directed by Engr-in-Charge.

M & L for preparation of newly plastered or unplastered surfaces of walls and applying three coats of white wash, complete all as specified and as directed.

M & L for preparation of newly plastered or unplastered surfaces of walls and applying two coats of oil bond distemper, white or tinted over a coat of primer, complete all as specified and as directed.

M & L for preparation of old treated surfaces of walls and applying one coat of oil bond distemper, white or tinted, complete all as specified and as directed.

M & L for preparation of new plastered or unplastered surfaces of walls and applying two coats of cement base paint of any shade complete all as specified and directed.

S & F 3 mm thick plain sheet glass ordinary quality, and glazing with oil putty or wooden beads in squares n.exc 0.50 Sqm in each pane, complete all as specified and as directed.

S & F 3 mm thick figured glass, pin head type and glazing with oil putty in squares n.exc 0.50 Sqm in each pane, complete all as specified and as directed.

M & L for prepartion of new wooden surfaces of any description not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer, complete all as specified and as directed.

M & L for prepartion of old wooden surfaces of any description not otherwise described, over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed.

M & L for preparation of new steel surfaces of any description not otherwise described, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer, complete all as specified and directed.

Taking up/down steel tubing and connections including cleaning for refixing or removal to store 15mm/ 20mm bore pipes all as specified and as directed.

S & F Steel tubes, 15 mm bore, galvanised, "medium grade" with all fittings and fixtures and short lengths, fixed to wall and ceiling or laid in floor including cutting chases for concealed work etc, complete all as specifed and as directed.

S & F Steel tubes, 20 mm bore, galvanised, 'medium grade' with all fittings and fixtures and short lengths, fixed to wall and ceiling or laid in floor incl cutting chases for concealed work etc, complete all as specified and directed.

S & F rotational moulded polyethylene water storage tank 500 Ltrs capacity, ISI marked (cylindrical vertical with closed top), double wall layer construction, hoisted and fixed in position complete all as specified in SSR Part-I, complete all as specified and directed.

S & F Bib tap, cast copper alloy, fancy type, screwed down, screwed for iron pipe, 15 mm bore, complete all as specified and as directed.

S & F Pillar tap, cast copper alloy, with capstan head, chromium plated, screwed down high pressure, with or without lettered hot/cold with long screwed shanks and fly nuts screwed for iron pipe 15 mm bore, complete all as specified and as directed.

S & F 15 mm bore stop/angle valves cast copper alloy, screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or union, complete all as specified and as directed.

S & F 20 mm bore stop valves, cast copper alloy, screwed down, high pressure with crutch or butter fly handle, screwed both ends for iron pipe or union, complete all as specified and as directed.

S & F Ball valves high pressure of PTMT for 20mm bore pipe with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed. (Minimum weight 20mm-210gms), complete all as specified and as directed.

S & F PVC connection suitable for 15 mm pipe with PTMT nuts and washers for both ends of length 450 mm long, complete all as specified and as directed.

S & F Sink with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes coupling , inlcuding bedding in cement mortar to dwarf wall or providing cantilever brackets, PVC waste pipe and connecting union to pipe overall size 915 mm x 460 mm and bowl size 410 mm x 330 mm x 160 mm (fixed in repair), complete all as specified and as directed.

S & F Vitreous china squatting pan water closet, orissa pattern, size 580 x 440 mm white with integral foot rests (excluding flushing cistern and flush pipe) including PVC (SWR) 'S' trap and provision of lime concrete bediing and jointing to flush pipe, complete all as specified and as directed.

S & F 10 litres capacity PVC, low level, valveless, syphonic action type flushing cistern, inlet ball valve, float valve, handle and fixing arrangement, 32 mm dia PVC flushing pipe and 15 mm dia 450 mm long PVC connection with PTMT waste coupling (fixed in repair), complete all as specified and as directed.

S & F Vitreous china, wash hand basin, (white) of size 550 mm x 400 mm including PTMT waste coupling 32 mm dia with long screwed shank and fly nuts, PVC, medium grade 32 mm dia waste pipe, chain and plug, porcelain stopper , PVC connection 15 mm dia, 450 mm long with brass CP nuts and washers at both ends (fixed in repair), complete all as specified and as directed.

S & F 110mm bore UPVC (SWR) pipes, type 'B', single socketed, in any length, fixed to walls complete all as specified and as directed.

M & L for hand packing with broken stone or boulders or loose filling with aggregate of gauge 40 to 80 mm in back of walls /Back side abutment at weep holes areas etc all as specified and directed.

Extra labour over stone walling for hammer dressing to face stones and dressing of face beds and joints as specified of random rubble walling, uncoursed or brought upto courses, hammer dressing with maximum depression on face from straight edge held against the dressed surface n.exc 40mm granite or trap stone all as specified and as directed.

M & L for 100 mm thick, PCC (1:2:4), type B-1 (using 20 mm graded stone aggregate) as in pavings/ floor etc., finished fair and even without using extra cement all as specified and as directed.

Removing excavated material (soil) to a distance exc.1.5 Km but n.exc 5 Km and depositing where directed at a level n.exc 1.50 m above the starting point all as specified and as directed.

Removing excavated material (soil) to a distance exc. 250m and n.exc 500m and depositing where directed at a level n.exc 1.50 m above the starting point all as specified and as directed.

Surface excavation n.exc 30 cm deep and averaging 15 cm deep and getting out in hard / dense soil all as specified and as directed.

M & L for providing plain cement concrete (1:2:4) type B-1 (using 20mm graded stone aggregate) as in sub floors ,sub base, floors and pavings etc., 50mm thick, finished fair and even all as specified and as directed.

M & L for pre-polished coloured machine pressed precast concrete interlocking paver block rubber moulded type, any shape and size confirming to IS 15658-2006 of 60 mm thickness M-35 grade including jointed and pointed in neat cement slurry with pigments laid over and including sand filling to an average thickness of 40mm with 'M' Sand all as specified and as directed.

M & L for pre-polished coloured chequered cement concrete tiles in floors, machine pressed, factory made of size 300 x 300 x 25mm thick, with grey cement and pigment, set, jointed and pointed in neat cement slurry, laid over and including15mm thick screed bed in CM (1:6), complete all as specified and directed by Engr-in-Charge.

M & L for Precast renforced cement concrete (1:2:4) type B-1 (using 20 mm graded stone aggregate) as in cover slabs with plain fair faces inclduding setting in CM (1:4) all as specified and as directed. Note : Reinforcement shall be measured and paid seperately.

M & L for mild steel round bars 10 mm dia and over cut to length bent to shape required including cranking, hooking ends and binding with mild steel wire annealed not less than 0.9 mm dia all as specified and as directed.

Excavation over areas, n.exc1.5 mtr deep and getting out in hard /dense soil all as specified and as directed.

Rough excavation n.exc 1.5 m deep and getting out in soft/loose soil all as specified and as directed.

Demolition and breaking up SGSW/ RCC/PVC pipes upto 150mm bore set in cement mortar and taking out of trenches complete all as specified and as directed.

S & F UPVC ( SWR) pipes, type 'B', single socketed in any length,laid in trenches or in floors 160 mm (OD) all as specified and as directed.

M & L for PCC (1:3:6) type C-2 (using 40 mm graded granite stone aggregate) in concrete bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested for pipes of 150 mm bore all as specified and directed.

M & L for PCC (1:2:4) type B1 (using 20mm gradded stone aggregate) as in coping, cills, bands, lintels n.exc 1.5m length, string courses,apex stone,bed plates, kerbs and the like incl form work, weathering, slightly rounded or chamfered angles and throating all as specified and directed by Engr-in-Charge.

M & L for Brick work with subclass B bricks, straight or curved on plan, exc 6m mean radius built in CM (1:4) all as specified and as directed.

M & L for rendering 15mm thick in CM (1 : 4) mixed with water proofing compound as per manufacturer's instruction ,on fair faces of brick masonry surface/concrete surfaces finished even and smooth without using extra cement all as specified and as directed. Note: Water proofing compound shall be measured and paid seperately .

M & L for cutting into existing manholes for connnecting new drains 150 mm dia,making good to pipe and rendering,cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete (1:2:4) type B I smooth finished ,and reforming benching as required all as specified and as directed.

S & F mild steel TMT bars 10 mm dia and over cut to length bent to shape required including cranking, hooking ends and binding with mild steel wire annealed not less than 0.9 mm dia all as specified and as directed.

Supply only liquid water proofing compound all as specified and as directed.

S & F for UPVC sliding window frame shall be made of UPVC material conforming to IS-10151 of the window frame of extrude UPVC section having overall dimension of 100 x 62 x 50mm having wall thickness 2mm (+) or (-) 0.2mm .Corners of wall frame shall be jointed by MS galvanised bracket joints mitred and plastic welded.The hinge side vertical outer frame shall be reinforced with galvanised MS Tube of wall thickness 1mm (+) or (-) 0.1mm and the tie rod shall be provided at the bottom of the frame ,the window system should be glazed with 5.5mm thick glass of size required fixed in window frame 2 track and 2 shutters locking arrangement and rubber gasket and necessary clipping etc complete as per manufacture's instruction including all fittings and necessery locking arrangements all as specified and as directed.

S & F for UPVC fixed window, frame shall be made of UPVC material conforming to IS-10151 of the window frame of extrude UPVC section having over all dimension of 100 x 62 x 50mm having wall thickness 2mm (+) or (-) 0.2mm .Corners of wall frame shall be jointed by MS galvanised bracket joints mitred and plastic welded.The hinge side vertical outer frame shall be reinforced with galvanised MS Tube of wall thickness 1mm (+) or (-) 0.1mm and the tie rod shall be provided at the bottom of the frame, the window system should be glazed with 5.5mm thick frosted glass of size and fixed with frame and rubber gasket , necessary clipping etc complete as per manufacture's instruction including all fittings and necessery locking arrangements all as specified and as directed.

E/M PORTION Taking down old, unserviceable aluminium point wiring (light, fan, socket or power) complete, including fixture & fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc., removing materials to store for keeping in safe custody or for taking credit & making good the disturbed surfaces of walls, floors, etc., complete all as specified and as directed.

Taking down old sub-main wiring including fixtures & fittings etc., and removing materials to store for keeping in safe custody or for taking credit & making good the disturbed surfaces of walls, floors, etc., complete all as specified and as directed.

Disconnecting /dismantling of old existing unserviceable DB's any way 240/415 Volts with their old/unserviceable burnt MCB's all as specified and as directed.

M & L for surface point wiring with 1.5 Sq mm, FRLS PVC insulated, single core, copper conductor cable, 1100 Volt grade, multi stranded in and including PVC capping casing medium grade for one light /exhaust fan /socket outlet 5 Amps independent /call bell point controlled by one switch with and including continuous 1.5 Sqmm PVC insulated single core copper conductor cable earth continuity conductor green in colour connected to common earth and earth dolly, in and including PVC/ polycarbonate rectangular block/boxes of suitable size & thickness with suitable PVC/ polycarbonate cover for mounting switches, sockets etc.,complete all as specified and directed by Engr-in-Charge for the following:- (a) One Light /fan/call bell point controlled by one switch 5/6 Amps. Make : Havells/Finolex/Polycab . Note :-The wiring shall be done in proper color coding using red, yellow, blue for phases, black for neutral and green for earth.

(b) One switch socket out let point 5/6 Amps on same board.

(c) One switch socket out let point 5/6 Amps on independent board.

M & L for surface point wiring with two single core 2.5 Sqmm FRLS PVC insulated, single core, copper conductor cable, 1100 volt grade, ISI marked with multi stranded in and including PVC capping casing medium grade in wall for 15/16 Amps switch-socket outlets etc., on independent board complete and including continuous 2.5 Sqmm PVC insulated single core copper conductor connected to common earth dolly, in and including PVC/ polycarbonate rectangular block /boxes of suitable size & thickness with suitable PVC/ polycarbonate cover for mounting switch, sockets etc. complete all as specified and directed by Engr-in-Charge. Make : Havells/Finolex/ Polycab. Note :- The wiring shall be done in proper color coding using red,yellow,blue for phases, black for neutral and green for earth.

M & L for surface sub-main wiring alongwith earth wire of size (2 x 4.0) Sq. mm + (1 x 4.0) Sq. mm earth wire, ISI marked, FRLS, PVC insulated, multi stranded, copper conductor, single core cable drawn through and including PVC capping casing (medium grade) with all fittings and accessories ISI marked complete all as specified & as directed. Note :Two runs of PVC wire, one run of earth wire & one run of PVC capping casing (medium grade) shall be measured as one length. Make : Havells/Finolex/Polycab

S & F switch socket combination, 5 in 1, 5/6 pin, 15 Amp flush type, 240 volts, ISI marked complete all as specified and as directed. Make : Havells/Anchor/Legrand/C&S

S & F switch piano, flush button, single pole, one way, 5/6 Amp, 240 volts, ISI marked complete all as specified and as directed. Make : Havells/Anchor/Legrand/C&S

S & F switch socket outlet 5 Pin, 5/6 Amp flush type, 240 volts, ISI marked complete all as specified and as directed. Make : Havells/Anchor/Legrand/C&S

S & F socket out let 5 Amps, 240 volts, ISI marked complete all as specified and as directed. Make : Havells/Anchor/Legrand/C&S

S & F bell push, flush type, 5/6 Amps complete all as specified and as directed. Make : Havells/Anchor/Legrand/C&S

S & F call Bell, AC, Ding Dong type 230 Volts complete all as specified and as directed. Make : Anchor, Cat No: 8272 or equivalent in Legrand/C&S/Havells.

S & F ceiling rose, PVC/polycarbonate, insulated body, 3 terminals and 240 Volts, ISI marked complete all as specified & as directed. Make: Havells/CG/Anchor

S & F ultra slim elegance LED lighting fixture with extruded aluminium heat sink, 20 W, 4ft energy efficient and environmental friendly complete all as specified and directed. Make : Havells, Cat No : LUMILINEPLUSBS 20WLED865SPCSS or techno-commercially equivalent of Luker/Philips.

S & F Compact & sturdy LED decorative fixture ( 10 W) with extruded heat sink, multi purpose lighting in replacement of 2ft FTL fittings complete all as specified and directed. Make : Havells, Cat No: LUMILINEPLUSBS10 WLED865SPCSS or techno-commercially equivalent of Luker/Philips.

S & F decorative wall mounting fixture with opal PC diffuser suitable for lamps with B22 base with all accessories internally prewired and including connecting up with and including twin/three core twisted flexible copper conductor cable of suitable size in flexible conduit all as specified and as directed. Make: Havells, Cat No: LHDL07150099 (Beetle) or techno-commercially equivalent in Philips/Luker. Note: The cost of making good and matching to the existing surface is deemed to be included in the unit quoted rates.

S & F energy saving new generation 10 W LED, bulk head luminaire with opal diffuser with and including lamp LED 6000K complete all as specified and as directed. Make: Havells, Cat No: RUGBYNEONFT10W LED860SSYMTOPC or equivalent models in Philips/Luker.

S & F LED light fittings of 25 W rating, 6K colour temperature with IP 66 protection fixing to the wall using suitable GI bracket, GI pipe and nut bolts, making connections from ceiling rose etc., complete all as specified and as directed. Make: Havells, Cat No: ENDURAPEARLSL25 WLED757SASYTOPC or equivalent in Philips/Luker.

S & F fan exhaust, single phase, 250mm sweep, PVC body with their all accessories fixed properly on window/ stone wall surfaces of thickness not exceeding 50cm including making proper sized exhaust hole of 250 mm dia, louver Shutter suitable for the same exhaust fan and which shall easily be operated with exhaust air pressure and any disturbed surfaces of wall shall be made good by cement work /plastering and matching by existing colour white/colour wash including removing of old exhaust fan and connecting up/with and including twin / three core flexible cable of suitable size / type in flexible conduit and complete all as specified and as directed. Make: Havells, Code:Venti Air-DX white or equivalent in Almonard/ Usha. Note : Old exhaust fan shall be handed over to MES Store Yard.

S & F MCB, DB, TPN, 6 ways, double door type, IP-43, IK-09 with metal door, rated bus bars, earth bar, neutral links complete including blanking plates as required & fixed flush to wall/other surface complete all as specified and as directed by Engr-in-Charge. Make: Havells, Cat No: DHDNTHODDW06 or equvalent in Legrand/L&T. Note:The MCCB and MCB's shall be paid separately under relevent items.

S & F MCB TPN, 63A rating, 415 Volts, 10 KA `C' Series all as specified and directed by the Engr-in-Charge. Make: Havells, Cat No: DHMGCFPF063 or equivalent in Legrand/L&T.

S & F Sheet metal enclosure for 6 way DBs double door type 240 volts, 200 Amps rated bus-bar IP-43,IK-09 with metal door, including necessary connection all as specified and as directed. Make: Havells,Cat No :DHDNSHODDW06 or equivalent in L&T/ Legrand.

S & F miniature circuit breakers, single pole,C-Series, 240 Volts of capacity (6-32 Amps) as ordered breaking capacity 10 KA all as specified and as directed. Make: Havells,Cat No: DHMGCSPF006-032 or equivalent in L&T/ Legrand.

S & F miniature circuit breakers, SP & N, C-Series 240 Volts of capacity (6-32 Amps) as ordered breaking capacity of 10 KA all as specified and as directed. Make:Havells,Cat No : DHMGCSNF006-032 or equivalent in L&T/Legrand.

M & L for earthing complete with galvanized steel earth plate electrode 600 x 600 x 6 mm thick burried directly in ground (in vertical position) earth pit not less than 2.25 mtr below normal ground level with the top edge of the earth plate not less than 1.5 mtr (B.G.L.) and connected to galvanized iron earth strip 32 x 6mm dia by means of GI bolts,nuts, check nuts, and washers of galvanized iron including PCC pit & cover with suitable handle, including necessary excavation and earth work in any type of soil, 20 mm dia medium grade galvanized steel tube for watering with one end fixed with cast iron funnel and wire mesh, 40 mm bore medium grade galvanized steel tubing for drawing earth lead GI strip protection (upto 7.5mtr length) & common salt, charcoal in alternate layers etc. complete all as shown in Electric Plate No 3 of SSR Part 1 and testing on completion including taking down old earthing complete all as specified and as directed. Note: If necessary earth resistance value not obtained after testing, the conractor should do fresh earthing at free of cost.

SREERAM

S.RAMACHANDRAN

GUNASEKARAN AND CO