PROVN OF SHED NEAR MAIN GATE AT AF STATION SONEGAON , NAGPUR

Amount

Excavation over areas in soft/ loose soil n. exc. 1.50m deep and getting out complete all as specified and directed.

Excavation over areas in hard/dense soil n. exc. 1.50m deep and getting out complete all as specified and directed.

Removing of surplus excavated material to a distance not exceeding 50 mtr and depositing where directed at a level not exc 1.5 mtr above the starting point all as specified and directed.

Returning, filling in and including spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick complete all as specified and directed.

M&L for Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering complete all as specified and as directed.

M&L for broken stone or boulders hardcore of gauge n. exc. 63mm, deposited, spread and leveled in layers n. exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L for providing PCC (1:4:8) type D-2 using 40mm graded stone aggregate as in foundation filling mass concrete complete all as specified and directed.

Use and waste of formwork to foundations, fillings, bases of columns, rafts & raft beams, sides & siffits of foundation & plinth beams and similar works; vertical or batter for rough finished surface of concrete complete all as specified and as directed.

Use and waste of formwork to sides of pillars, posts, struts, piers, columns and stanchions, rough finished surface of concrete square, rectangular or polygonal complete all as specified and as directed.

M&L for providing RCC (1:2:4) type B-1 using 20mm graded stone aggregate as in foundations including rafts, footings, foundation beams, plinth beams, bases for columns etc., and mass concrete complete all as specified and directed.

M&L for providing RCC (1:2:4) type B-1 using 20mm graded stone aggregate as in pillars, posts, struts, piers, columns and stanchions complete all as specified and directed.

M&L for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends & binding with & including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for mild steel TMT bars 5mm dia and over up to and including 10mm dia in stirrups, spacers and binders cut to length, bent to shape required and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips quality conforming to Fe-500D complete all as specified and as directed.

S&F rolled mild steel framed work as Joist, channel, angle, or tee sections,fixed independently, without connecting plates, etc. Fe- 290 E-165 complete all as specified and directed.

S&F rolled mild steel framed work as in main and cross beams, hip and jack rafters purlins where connected to common rafters and running rails and guides for sliding doors fixed with angle cleats or other connecting plates Fe 410-w (Gde-E-250)quality A complete all as specified and directed.

S&F Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment. Fe 410-w (Gde-E-250)quality A complete all as specified and directed.

S&F 11mm to 15mm dia Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exc 5cm and not exc 10cm long complete all as specified and directed.

S&F 16mm to 20mm dia Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exc 22.5cm and not exc 30cm long complete all as specified and directed.

S&f Curved Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering including self tapping screws and self drilling screws of appropriate size with rubber washer for water tight fixing complete all as specified and directed.

S&f 2mm thick Curved Fibre glass reinforced translucent corrugated sheeting with two corrugations side lap fixed with coach screw and washer in roof complete all as specified and directed.

M&L for providing 150mm thick PCC 1:3:6, type C2 using 40mm thick aggregate as in sub base of floor / hard standing with proper slope maintained for self drainage complete all as specified and directed.

M&L for providing 160mm thick PCC 1:2:4, type B1, using 20mm graded crushed stone aggregate as in floors with proper slope maintained for self drainage and finished the surface even and smooth without using extra cement all as specified and as directed.

M&L for Mild steel sheet of 1mm thick eaves gutters, galvanised class 3, half round of dia 150mm with rounded edges complete all as specified and as directed.

M&L for nozzle pieces (Out lets) for eaves gutter complete all as specified and as directed.

M&L for Cast iron rainwater socketed pipes 100 mm dia with cement joints, without ears complete all as specified and as directed.

M&L for Bends or elbows, square, or obtuse of dia 100mm complete all as specified and as directed.

M &L for preparation new steel and iron surfaces not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of primer of red oxide complete all as specified and as directed.

M &L for welding of metal having thickness exc 6mm but not exceeding 9mm complete all as specified and as directed.( The rates include for cleaning and preparing the surfaces to be welded together, holding the members in true position while welding and bevelling of edges, as required, in the case of metal exc 3mm thick)

dhanshree enterprises

M/s S. S. MUNDE

karambir constructions