SPL REAPIR TO WEST HUTMENT (D AND V) AT KASHMIR HOUSE UNDER GE NEW DELHI

Demolition of Concrete of any description and in any position not otherwise specifically provided for removing the unserviceable material out side the MOD land.

M & L for Hardcore of guage exc 63mm but n exc. 100 mm, Broken or boulders stone deposited, spread and levelled in layers n exc. 15 cm thick, watered and rolled/rammed to a true surface

M&L 75mm thick cement concrete type D-2 1:4:8 (40 mm graded agg) as in sub base of floors

Dismantling brick tiles or terracing tiles single layer on roof laid, bedded and pointed in any mortar incl removing the unserviceable material out side the MOD land.

S&F modular switch flush type, 6 Amp. SP, two way ,1 module(IP-21) all as directed specified. Make-Havells Murano, Indoasian-Shyonara, Legrand-Arteor

Supply Liquid water proofing compound

M&L for guniting in ceilings for a high quality finished requires careful and skillful handling using skilled labours, good scaffolding stuff material mainly woodens or steel rakers, the surface should include thorough cleaning through air blasting or high pressure water jets. Additionally sandblasting with the gun, minus cement and at low velocity, effectively remove dust from reinforcement. if surface tends to absorb, it should be kept moist for six hours before guniting. Guniting requires wire netting ranging from 1.5mm to 3mm thickness spread uniformly throughout the surface fixed with tinned tacks of wire stapples, a portland pozzolona cement, a guniting ratio of 1:3 is typically employed, water cement ratio for guniting is normally set at .3, maximum size of sand should not exceed 10mm and the distance between the nozzle and the backing surface should not exceed 1m. further nozzle velocity should not surpass 140m/s. in structure repair scenarios, the gunite thickness should be limited to 30mm and rebound material is not advisable. Moreover rate of deposition of guniting is 15m3/hr. Thin polyethene or paper or cloth sheets should be used to cover the entire wall area so that cleaning is maintained and also measures should be taken so that tiles are protected from the falling materials. Demolition if any should be done prior to start of guniting and procedure should be properly followed at site and directions by engg in charge is specified.

M&L for Dismantling floor hearth and wall tiling including cement mortar bedding (but not backing) and removing rubbish off the premises complete all as specified and directed.

Ditto as per Item No 114 above but with 2 x 2.5 Sqmm +1 x 2.5 Sqmm Copper conductor cable for one 3 pin, 15 Amps Switch socket out let on independent board.

ditto as in Item No-132 above but for 2x10.0 sqmm+1x10.0sqmm earth wire

Ditto as per Item No 148 above but for size 100x50mm.

Ditto as per Item No 151 above but for SPN DB 8way.Make- Legrand, LK(L&T), Schneider

M&L in reapir for wooden flooring, laminated wooden type made of high density fibre board (HDF), comprising of tongue and groove interlocking type of planks of 1210 x 193 mm size 8mm thick, commercial grade, abrasion resistance of AC-II category, over and including 6 micron polyethylene and foam cushion sheeting over the concrete surface to minimize moisture migration from the concrete including all fixing material i.e. chemical adhesive, base strip/fillets etc. veneered and matching top beading etc. complete all as specified and directed.

Dismantling wall, ceiling boards and pre fabrication boards incl frame of any description as in panelling ceiling, partition, cub boards etc incl cover fillets in any surfaces complete

S&F prelaminated PVC rigid foam sheet wall panelling of 5 mm thick stuck on inner frame work of 35 mm wide strips of 5 mm thick rigid foam sheet. The strips should have a groove of 6 mm width and 2 mm depth for sinking the head of screw used to fix the strips to the all and should be placed vertically at equal intervals of 300 mm C/C. The PVC strips to be fixed to the all using 65 mm long MS screws through the groove in the strip by using PVC fasters incl moulding at columns, windows and doors jambs. Note:- (a) Work for fixing of wall panelling shall be got executed through manufacturers authorised applicators only under the close supervision of their technical staff. (b) The entire qty of wall panelling and their allied ancillaries shall be procured directly from the manufacturer or their authorised dealer only.

M&L for providing and fixing False ceiling at any height with semi perforated 12mm thick mircro tegular edge GRG (Glass Fiber Reinforced Gypsum) false ceiling tiles of size 595x595mm of approved texture, design and patterns having moisture content less than 2%, humidity resistance of 99%, NRC 0.85 (with 50mm thick glass wool) as per IS 8225 :1987, Noncombustile as per BS 476 (part-4) -1970 and light reflectance of 75-85% to be laid in true horizontal level or in slope as per site requirement suspended on interlocking metal T-Grid of hot dipped galvanised iron section of 0.33mm thick (galvanised @ 120 grams per sqm including both sides) Comprising of main - T runners of size 15x32mm of length 3000mm, cross-T of size 15x32mm of length 1200mm and secondry intermediate cross T of size 15x32m of length 600mm to from grid module of size 600x600mm, suspended from ceiling using galvanised mild steel items (galvanizing @ 80 grams per sqm) i.e 50mm long, 8mm outer diameter M-6 dash fastners, 6mm dia fully threaded hanger rod up to 1000nn length and L shape level adjuster of size 85x25x2mm. Galvanized iron perimeter wall angle of size 24x24x0.40mm of length 3000mm to be fixed on periphery wall/partion with the help of plastic rawl plugs at 450mm center to center and 40mm long dry wass SS screws. The work shall be carried out as per specificatons, drawing and as per direction of Engineer-in-Charge complete all as specified and directed.

M&L for GI Metal Ceiling Lay in perforated Tegular edge global white color tiles of size 595x595 mm and 0.5 mm thick with 8 mm drop; made of GI sheet having galvanizing of 100 gms/sqm (both sides inclusive) and 20% perforation area with 1.8 mm dia holes and having NRC (Noise Reduction Coefficient ) of 0.5, electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending and perforation, and backed with a black Glass fiber acoustical fleece, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross "T" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main "T" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge. Note:- Make : - Diamond Ceilings/Armstrong/Knauf Ceiling/Durlum

M&L for mirror polishing on old surface of kota stone including rubbing polishing & treating the surface complete all as specified and directed. Note: Carborandum stone of 0 unit shall be used in polishing operation.

Taking down cement or cement lime plaster any description including racking out joints, hacking for key, scrubbing down with water etc complete all as specified & directed including removal of debris out side MoD land.

M&L 15 mm thick rendering fair/unfair faces of brick work on concrete surfaces finishing even and smooth without using extra cement in CM 1:6 on walls

M&L 5mm thick Rendering in CM (1:3) to soffits of slabs finished even & smooth complete all as specified and directed.

M&L for preparation of new plastered surface of ceiling and applying three coat of white wash complete all as specified.

M&L for preparation of newly plastered surface of wall and applying two coat of weather proof exterior emulsion extra premium 100% acrylic emulsion as approved over a coat of primer complete all as specified and directed.

M&L for providing PMM (Polymer modified cementitious mortar) :- (i) Dry sub strata surface and free of debris & dust (ii) Applying Epoxy bond coat on the sound substrate using approved spray machine & ensuring that no pin holes are visible.(In case pin holes are still visible after a coat, a second coat shall be applied to ensure absence of pin holes). (iii) Immediately after application of epoxy bond coat as above apply PMM (Polymer modified cementitious mortar) of 25 mm thickness. Note : Application of PMM shall be preferably be in coats of appx 10mm thickness. PMM work shall be executed in fairly rapid successions so as entire work is completed with in 30 mins). PMM shall be pre packed ready to use. (iv) PMM surface to be moist cured for three days followed by air curing in temperature as recommended by manufacturer complete all as specified and directed.

Taking down chowkhats or frame without taking off shutters exc 1.50 sqm but n.exc 4.0 sqm

S&F 12mm thick frosted/plain/tinted tuffened glass partition including door of size 1.20x 2.10m in two panels(0.60x 2.10 m each panels) with necessary frame work incl necessary fitting and fixtures such SS handle,floor spring (Godrej)/ EVERITE in required quantity incl etching the glass with Logo of the respective unit and border all alround the door as required complete all as specified and directed incl taking down the existing door and film complete all as per specification and directed.

Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia andlength complete as per direction ofEngineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). →→ Note: For WPC solid door/window frames,minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 35mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and nontoxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength50 N/mm2, modulus of elasticity 850 N/mm2 an

d resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, complete all as specified and directed. Note: stainless steel butt hinges shall be paid separately under relevant item)

Providing 30mm thick FACTORY-MADE WIRE MESH SOLID WPC DOOR SHUTTER consisting of Density 650 Kg /cum Manufactured by an ISO-9001-2015 certified Company, Door to be panelled with SS mosquito Mesh and XTN aluminium Mesh for additional strength and safety purpose. (Confirming as per IS:4020). The door should be water proof, termite proof, fire retardant and having screw holding capacity. Door to be fixed to frame with 3 nos. SS butt hinges size 100mm*25mm*2mm and 32mm long steel screws drilled suitable to pass through Other hardware should be fixed with 19*6mm size steel screws etc complete all as specified and directed Engineer-in-charge, manufacturer's specification & drawings.” Note: Fixture/fittings shall be measured & paid under relevant item

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm single side prelam PVC sheet used instead of Plain colour PVC sheet & edges will be painted to match with prelam sheet reinforced with M.S. Square tube, as per specification & drawing and as per drawing on SI page 180 of SSR (part II) complete all as specified and directed.

S&F factory made solid PVC Moulded Door shutter ,28 to 30mm thick with 2 raised pannels design with 2mm thick Moulded PVC Sheet on front face and 2mm plain colour PVC sheet on back face in frame at site as per specification and drawing on SI page no 181 of SSR (part II) with particle board core complete all as specified and directed.

S&F aluminium ornamantal grill 8mm dia 75x95mm aperture complete incl U channel complete all as specified and as directed

S&F in repair ZEBRA venetian blinds horizontal type incl guide rail, pulling thread etc incl taking down existing pelmets.

M&L for Non skid ceramic floor tiles 7 to 8 mm thick (square/rectangular) coloured , area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, of 1st quality , set and jointed with adhesive and pointed with epoxy grouts as per manufacture instruction to match over laid over screed bed or bedding layer in cement mortar 1:4, 15 mm thick for laying floor finishes complete all as specified and directed.

M&L for Glazed ceramic coloured walls tiles 450x300mm, 6/7mm thick, for works on vertical surfaces such as skirting/dados of 1st quality , set and jointed with adhesive and pointed with epoxy grouts as per manufacture instruction to match over including rendering 10mm thick on fair faces or other than fair faces of brick work in cement mortar 1:4, finished even and fair as in backing layer complete all as specified and directed.

Demolition of stone slabs and tiles of any description or thickness in floors, wall aprons etc laid bedded and pointed in any mortar incl mortar screed of any description incl removal of debris from site.

Dismantling wrought or mild steel work of any description not otherwise provide for in any height upto two strey incl necessary scaffolding where required.

S&F structural mild steel work as in roof trusses (framed), trussed, post, purlins, crane gantries, rails and fastenings and heavy bracket framingetc (beam, tee, angle, channel or flat section) including distance pieces, cleats etc confirming to Fe-410-0 or Fe 310-0 complete all as specified and directed.

S&F mild steel framed work such as grills, grating etc with end of bars shouldered and/ or riveted or forged into spikes, framed guard bars,barred iron doors, ladders, framed balusters, walk ways, tank cage, railings and similar work confirming to Fe-410-0 or Fe 310-0 complete all as specified and directed.

S&F for Steel work in tubular trusses confirming to Fe 410-W Gde 250 A including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 complete all as specified and as directed

M&L for two coats of synthetic enamel paint on new steel and iron surfaces over a coat of red oxide primer incl preparation of surfaces over 10 cm width of girth.

Demolition of brick work or stone masonry built in cement mortar or cement lime mortar.

M&L brick work with old size sub class B" bricks straight or curved on plan exc 6m mean radius in CM 1:4 (work incl parapet walls, manhole, drain etc)

M&L for Vitrified Ceramic tiles in light shade (square/ rectangular) area of each tiles not exceeding 0.36 sqm, in floors etc.set and jointed with adhesive and pointed with epoxy grouts as per manufacture instruction to match over including 15mm thick screed bed in cement mortar (1:4) complete all as specified and as directed.

S&F 4mm thick aluminium composite panel sheet of any choice colour fixed with self taping screw/bolt in any height upto two storey building including necessary double steel scaffolding where required complete all as specified and as directed incl necessary double steel scaffolding where required upto two storey bldg.

S&F 10 mm thick coloured polycarbonate multiwell sheet manufactured from high quality, UV stabilzed resins in roof covering incl necessary fittings & fixtures like aluminium strips, aluminium tee, coach screw and washers etc with silicon joints filler for fixing complete of any colour all as specified and directed by engineer in charge

S&F in repair 50 micron solar control film sticked to glass panes as per manufacturer instruction reflective type complete all as specified and directed.

Demolition in machinical process of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for complete all as specified and directed.

M&L for cement concrete 1:4:8 type D-2 (using 40 mm graded crushed stone aggregate) as in sub base, or sub floors foundations, filling and mass concrete complete all as specified and directed.

Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand all as specefied and directed

M&L for cement concrete chequered PU coated tiles 300x300x25 mm thick with grey cement and no pigment, set and jointed in neat cement slurry and pointed in coloured cement to match the surfaces as in floors over and including 20 mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

S&F in repair urinal vitreous china including waste coupling and fixing acessaries of siz

S&F in repair wash hand basin vitreous china white, counter basin of size 540X480 mm including making good the surface/joints with white cement complete all as directed by Enge-in-Charge. Make : CERA CAT Part No: 1009.

S&F in repair15mm bore of medium grade galvanised steel tubing with all fittings and fixed complete to wall complete all as specified and directed.

S&F in repair fancy type 15mm dia chromium plated quarter turn fancy type wall mixer hot & cold with long swan for kitchen sink fixing and connection to pipes complete all as directed. Make Jaquar FLR5309N ,CERA F1003501,Hindware F570027

S&F in repair C.P. brass towel ring fixed to wooden / PVC cleats with C.P. brass screws including cutting and making good the walls wherever required complete all as specified and directed.

M&L for Vitrified Ceramic tiles in light shade (square/ rectangular) area of each tiles not exceeding 0.36 sqm as in skirting laid on 10mm thick cement plaster in CM (1:3) ,set and jointed with adhesive and pointed with epoxy grouts as per manufacture instruction to match over

S&F in repair Toilet paper holder of vitreous china fixed to walls with chromium plated (CP) brass screws Toilet paper holder with flat recessed type stainless steel Complete all as specified and directed."

S&F in repair urinal spreader of PTMT any colour for fixing with 15mm dia pipe (minimum weight 60 gms)

S &F in repair waste coupling brass chromium plated for vitreous china, sink, WHB, urinals etc with long screwed shanked ad fly nuts 32 mm bore complete all as specified and directed

Dismantling water tanks of capacity not exceeding upto 500 litres complete.

Dismantling water tanks of capacity Exc 500 & n exc 1000 litres complete all as specefied.

S&F 1000 ltr capacity rotational moulded triple layered polyethylene water storage tanks (cylindrical vertical with closed top) white colour hoisted and fixed in position all as specified.

S&F drain pipes salt glazed stone ware pipe grade 'A' laid in trenches for 150mm dia & jointed as specified incl demolition and breaking up drain pipe set in cement mortar.

Excavating in trenches not exc 1.5m wide & N.exc 1.5m depth for foundation etc for shafts, wells, cesspits, manholes pier holes etc not exc 10 Sqm on plan & not exc 1.5m depth & getting out in soft/loose soil.

S&F in repair brass chromium plated tubular towel rails 20 mm dia D type ,60 cm long between flanges

S&F in repair small fittings galvanised iron medium grade such as socket, elbow, nipple, Tee, union etc for 15 mm bore pipe (ISI marked) complete all as specified and directed

S&F in repair small fittings galvanised iron medium grade such as socket, elbow, nipple, Tee, union etc for 20 mm bore pipe (ISI marked) complete all as specified and as directed.

S&F in repair 125 mm dia CP grating openable type with hinge as per sample over nahani/floor trap including embedding the same in white/coloured cement to match complete all as specified and directed

S&F powder coated aluminium partition n.exc 1.20 Sqm in each panel using 95.6 mm x 44.8mm x 1.6mm frame work with 12 mm thick exterior grade veneered particle boards with decorative veneers on both faces/5.50 mm thick frosted glass as directed by Engr-in-Charge including aluminium beading for fixing board

S&F in repair butt hinges 100 long medium weight cold rolled SS with SS hinges pins finished bright and smooth complete

S&F inrepair Aluminium alloy, anodised, sliding door bolt 300MM with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed.

S&F in repair CI door closer hydraulically regulated type designation NO 3 universal type suitable for door shutters 851 mm to 1000 mm complete all as specified and directed. Make : Hardwyan, M/s Prabhat

S&F in repair 140 mm door stopper aluminum alloy body and tongue anodized with hard drawn steel spring complete all as specified and directed

S&F in repair aluminium handle of150mm size cast type anodised (ISI marked) complete all as specified and as directed.

Taking down cement or cement lime plaster any description including racking out joints, hacking for key, scrubbing down with water etc complete all as specified & directed including removal of debris out side MoD land. The work shall be carried out upto sixth storey height of buildings.

M&L for 15mm thick ready mix plaster READIPLAST RP of (Make Ultra tech) on any surfaces of brick/concrete includidng aapplication of bonding coat as Ultratech seal and Dry 5 Plus as per manufacturers instruction including finished even and smooth complete all as specified and directed.The work shall be carried out upto sixth storey height of buildings including all safety factor.

M&L for 5mm thick ready mix plaster READIPLAST RP of (Make Ultra tech) on any surfaces of brick/concrete includidng aapplication of bonding coat as Ultratech seal and Dry 5 Plus as per manufacturers instruction including fin

S&F Pre- painted galvalume aluminum zinc coating GI based steel sheet with approved profile and 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws all as specified and directed by Engr-in-Charge.

Each set

Each Job

Make- Legrand, LK(L&T), Schneider

Ditto as per Item No 114 above but for one fan point

Ditto as per Item No 114 above but for one bell point controlled by one, one 5 amp switch

S&F in repair 15 mm bore chromium plated fancy type brass angular stop cock with wall flanged screwed down high pressure screwed both ends for iron pipe or for unions. Make : JAGUAR CAT Part No OPP-CHR-15053PM or equivelent as specified in list of make complete all as specified and directed by Engr-in-Charge

S&F in repair 15 mm bore brass chromium plated TWO way bib taps with knob to operate, complete all as specified and directed by Engr-in-Charge. Make : JAGUAR CAT Part No:VGP-CHR- 81041 or equivelent equivelent as specified in list of make

S&F in repair 300 mm Aluminium anodised barrel tower bolts of extruded section and fixed→, complete all as specified and directed.

to be included in the unit rate. The metal box shall be same make of switches/sockets.

M & L for one light point with 1.5 sqmm PVC insulated and unsheathed copper conductor multistranded 1100 volts grade, ISI marking drawn thorugh and new non metallic PVC rigid concealed conduit and conduit accessories, medium grade, ISI marking, concealed metal box for fixing switches, sockets, inculding one run of 1.5 sqmm PVC insulated unsheathed copper cable FRLS grade as in earth wire for continuity and connecting to earth dolly for one light point controlled by one switch complete including making good the disturbed surface by Putty and matching the colour of wall with the existing colour of the wall (wash/paint/distemper) wherever required(as per the existing condition) all as specified and directed. Note - The cost of modular metal flush box and Modular white Cover Plate with Frame, MS terminal boxes and blank plate if required shall be deemed

Per load

Taking down carefully old point wiring (Light /Fan/ Socket/ Bell Point) with aluminium/copper conductor cable complete including fittings such as ceiling rose,holders,regulators,bell,switch and socket from existing concealed conduits/casing caping and making good the disturbed surface of wall/ floor complete to match with the existing surface/finishes all as specified.

S&F modular socket outlet, 3 pin, 6 Amp, flush type 2 module all as directed/ specified. Make-Havells Murano, Indoasian-Shyonara, Legrand-Arteor

S&F modular Fan Regulator step type 2 module,120W all as directed/ specified

S&F modular AC BOX with 16-20 Amp mini MCB 230 Volts AC all as specified. Make-Make- Havells-DHFNCSPA016, LK(L&T)- CB93101KW16, Schneider-P8016-N

S&F modular switch flush type, 6 Amp. SP, one way ,1 module (IP-21) all as directed specified. Make-Havells Murano, Indoasian-Shyonara, Legrand-Arteor

Ditto as per Item No 114 above but for one light point controlled by two two way switches

S&F bell, AC, 230 V, SP, ding dong type all as directed & specified.

S&F Ceiling rose 3 phase, PVC/ Polycarbonate body all as directed/ specified.

Taking down old unsv submain wiring of any size complete all as specified and directed.

S&F in replacement LED tube light fitting 1x 20 watts, 220 volts AC, 1200mm, with Aluminium housing & integrated electronic driver complete with driverwith polycarbonate diffuser & thd, 10 % including connecting up with three core twisted flexible copper conductor cable of suitable size from ceiling rose complete all as specfied.Make-Philips, Orient, Bajaj,havells

S&F in replacement LED light with high output diffuser 2 feet, 10 watts, 220 volts AC decorative type complete with driver, holders & including suitable LED lamp including connecting up with three core twisted flexible copper conductor cable of suitable size complete all as specified. Make-Philips, Orient, Bajaj,havells

S&F in replacement LED luminaire 600 x 600 x2 mm, (2'x2') 36 watts, 220 volts AC Recess/Surface mounted downlighter type with high efficiency PMMA diffuser, soft glare free light complete with suitable driver, holders & including suitable LED lamp suitable for POP/Gypsum/roof ceiling including connecting up with three core twisted flexible copper conductor cable of suitable size from ceiling rose including cutting of false ceiling in suitable size & making good the disturbed surface & matching with the existing surface complete all as specified. Make-Philips, Orient, Bajaj,havells

S&F in replacement LED luminaire Recess/Surface mounted downlighte (Round/Square)r with pressure die cast alluminium heat sink & PC diffuser round shape 15 /18 watts warm white/cool white, 220 volts AC,Cut out dia 6 inch finished in white white powder coated complete with integrated driver, holders & including suitable LED lamp including connecting up with three core twisted flexible copper conductor cable of suitable size from ceiling rose including cutting of false ceiling in suitable size & making good the disturbed surface & matching with the existing surface complete all as specified. make-Make-Philips, Orient, Bajaj,havells

S&F in replacement engagement lights including 5W LED coloured Adore Lamp B22 Red and green suitable for bulb holder. Complete all as specified and as directed by Engr-in-Charge.

S&F in replacement road/ security light/bldg light with high power LED fitting as light source ,energy saving envoirmental friendly 60 W with advance features all as complete with fixing arrangement such as GI pipe brakets bend in 120 degree, clamps made out by GI strip suitable for steel or PCC poles, nuts ,bolts and washer to be fixing incl PVC spike fixed over the light for protection to monkey and making all eclectrical connection with three core flexible copper cable etc specified and directed. Make-Philips, Orient, Bajaj,havells

S&F in replacement ceiling fans complete with blades, down rods, accessories, 230 V, 1200 mm sweep. Min air delivery 230 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) ceiling fan with remote of color white or (as per site requirment) complete with all accessories internally pre wired and including connecting up with three core flexible copper conductor cable with suitable size and making arrangement to hanging of fan to ceiling with proper hook nut bolt acomplete all as specified and directed. Note:-Taking down fan, sealing cable ends,dismantling blades depositing the same to MES store yard and in safe custody.Make- Orient-Ecotech prime, Bajaj-Ethora plus, Havells-Enticer Prime

S & F in replacement METALIC EXHAUST fans AC single phase 230/240 V of size 300 mm sweep (as per sample ) complete all as specified and directed.Make-Usha, Bajaj,Havells Note:-Taking down fan, sealing cable ends,dismantling blades depositing the same to MES store yard and in safe custody.Make-Usha, Bajaj,Havells

S & F in replacement PVC body ventilation fan 250mm Sweep, 240 Volt, AC 50 HZ ,plastic body including louvers with and including cutting bricks/stone boulders wall for fixing of fan and finished the cutting surface even and smooth by using cement morter complete all as specified and directed by Engineer in charge.Make-Usha-CrispAir, Bajaj Maxima Neo 250, Havells Ventilair DX Note:-Taking down fan, sealing cable ends,dismantling blades depositing the same to MES store yard and in safe custody.

S & F in replacement of wall fan 400mm (16 inch) 60 watt Oscilating wall fan (KD white) wall mounted speed 1350 RPm completet allas specified and directed by Engineer in Charge Make :bajaj,crompton,havellsand including cutting bricks/stone boulders wall for fixing of fan and finished the cutting surface even and smooth by using cement morter complete all as specified and directed by Engineer in charge.Make-Usha, Bajaj,Havells Note:-Taking down fan, sealing cable ends,dismantling blades depositing the same to MES store yard and in safe custody.

S & F GI Raceway ISI marked made from 1.5mm thick pregalvanized sheet for top,bottom & sides and complete with top cover with rubber gasket of size 100x38mm complete for mounting and supporting the cable tray system,along with vertical bends, including taking down and re fixing and type of electric/signal cable, if require through wall/floor cutting and making good surface of disturbed area, complete all as specified and directed.

Ditto as per Item No 114 above but for One 3 pin 5 Amp socket outlet on the same board

S & F in repair GI bracket for raceway mentioned in above item here-in-before of 100mm width, complete all as specified and directed.

S & F in repair coupler for raceway of 100 mm width complete all as specified and directed.

Ditto as per Item No 114 above but for One 3 pin 5 Amps socket out let on independent board

S & F PVC duct cable tray/ wiring channels for top,bottom & sides and complete with top cover with rubber gasket of size 100x100mm complete for mounting and supporting the cable tray system,along with vertical bends, including taking down and re fixing and type of electric/signal cable, if require through wall/floor cutting and making good surface of disturbed area, complete all as specified and directed.

M&L in replacement for sheet metal enclosure VTPN-DB 4 way 415V,double door 250A copper bus bar IP 43,Suitable for 63-160Amp MCCB as incomer as flush mounted complete all as specified and as directed.Make- Legrand, LK(L&T), Schneider

replacement of factory made concealed sheet steel distribution boards, double door, SPN, 4 way, 230 volts AC, IP 43 with suitable busbar, neutral link, earth link suitable for MCB,DP/SPN 200Amps rated bus bars as incomer & MCB SP as outgoing all as specified.Make- Legrand, LK(L&T), Schneider

S & F in repair MCCB 4 Pole 415V Fixed type 40-63A with breaking capicity 16 KA complete all as specified and directed.Make- Legrand, LK(L&T), Schneider

S & F in replacement of MCB SP 6-32 Amp, 10kA all as specified. Make- Legrand, LK(L&T), Schneider

S & F in replacement of moduler Mini MCB SP 16-20 Amp,240V 3kA, C Curve, fitted in main switch board including 2.5 sqmm wire connecting socket & modular MCB complete all as specified. Make- Legrand, LK(L&T), Schneider

S & F in replacement of MCB SPN 32 Amp, 10kA all as specified.Make- Legrand, LK(L&T), Schneider

S&F Rigid non-metallic PVC conduit exclusive of boxes (junction/ terminal) but inclusive of all tees, bends,elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hooks etc. of following sizes

25 mm bore

40 mm bore

M & L for taking down of existing AC window type or split type and refixing the the same at its original position along with complete accessories including minor repiars and repair of PCB/ display, making good surface od disturbed area at wall complete all as specified and directed.

Supply and installation, testing and commissioning of hard drawn copper refrigerant pipes for AC units with necessary copper fittings, laid neatly, secured with GI clamps and wall brackets with pipe supports as per technical specifications, at every 1.5 meter interval and at bends including insulation with 19 mm thick class "O" nitrile rubber, UV treatment (coating) for exposed refrigerant piping insulation complete all as required at site as per specifications, of the following sizes, complete all as specified and directed

6 mm ( 1/4" ) thickness

9 mm ( 3/8" ) thickness

13 mm ( 1/2" ) thickness