Proposed Furnishing work of offices located at Ground Floor, 1st Floor and 9th Floor in Premium Suit Building, JUPMI Campus, Ranchi Smart City for Jharkhand Employees Grievance Tribunal, Jharkhand State Level Fee Regulation Committee and Jharkhand St

Jharkhand State Building Construction Corporation Limited Regd. Office: - Building Construction Department, Govt. of Jharkhand, Project Building, P.O. - Dhurwa, Ranchi-834004, Jharkhand Phone No.:- 0651-2446257/2446258/2446259, e-mail:[email protected]

Name of work : - Proposed Furnishing work of offices located at Ground Floor, 1st Floor and 9th Floor in Premium Suit Building, JUPMI Campus, Ranchi Smart City for Jharkhand Employees Grievance Tribunal, Jharkhand State Level Fee Regulation Committee and Jharkhand State Coaching Centre Regulation Authority under Higher and Technical Education Department, Jharkhand

Name of Agency/Supplier/Contractor

Sl. No Item. Item Description. Unit Rate

1 M.R Supplying, fitting, and fixing in position decorative WPC (Wood Plastic Composite) fluted louvers of specified thickness/depth (nominally 25 mm) and approved pattern/profile, mounted over a rigid internal structural framework of powder-coated aluminium tubular sections (nominal size 50 mm × 25 mm with minimum 1.2 mm wall thickness). The panels shall be factory-finished with exterior/interior grade anti-scratch laminate/foil finish in approved shade and wooden texture, fixed using heavy-duty concealed clips, SS screws, anchor fasteners, and structural adhesives. Rate shall be inclusive of all framing, alignment, levelling, corner/edge trims, end caps, labour, scaffolding, tools, tackles, wastage, royalty, and all applicable taxes complete in all respects as per architectural drawings and direction of Engineer-in-Charge. SQM

2 M.R ​Supplying and fixing premium quality commercial grade PVC / Vinyl-coated Wallpaper (minimum weight 280–350 GSM) of approved pattern, texture, design, and shade. Scope includes thorough surface preparation of the existing plastered/gypsum substrate by cleaning, repairing surface defects, applying wall primer, sanding, and applying heavy-duty antifungal, water-resistant wallpaper adhesive without leaving any air pockets, blisters, visible seams, or overlaps. Rate shall be inclusive of precise pattern matching, edge cutting, wastage, labour, royalty, and all applicable taxes complete in all respects as per specifications and direction of Engineer-in-Charg SQM

3 M.R Supplying and installation of custom-made Roller Blinds with heavy-duty operating mechanism, comprising superior quality blackout / semi-translucent polyester-coated PVC fabric (fade-resistant, anti-static, fire-retardant, and water-repellent) of approved design and shade. The system shall include heavy-gauge extruded aluminium top roller tube, aluminium bottom rail with end caps, heavy-duty brackets, smooth chain-drive/clutch control mechanism with durable stainless steel/plastic beaded control cord, and child safety cord tensioner. Complete with ceiling/wall mounting fasteners, hardware, labour, alignment, royalty, and all applicable taxes as per site requirement and direction of Engineer-in-Charge. SQM

4 M.R Providing and fixing in position custom Handmade Acrylic Canvas Painting created by experienced artists using high-grade lightfast acrylic paints on heavy-duty, stretched primed cotton/linen canvas in approved theme, composition, and colour palette as approved by the Architect/EIC. The artwork shall be protected with a protective coat of UV-resistant clear varnish and framed in a heavy-duty, moisture-proof, termite-resistant synthetic polymer/fibre moulding frame of approved width and profile, complete with 8–10 mm MDF/hardboard backing, corner brackets, heavy-duty hanging hardware, wall plugs, SS screws, handling, and mounting securely at designated locations, complete in all respects as per design and direction of Engineer-in-Charge SQM

5 M.R Supplying, installing, testing, and commissioning of premium vitreous china Rimless Wall Hung European Water Closet (EWC) with blind installation mechanism, finished in glossy white. Complete with matching heavy-duty UF (Urea Formaldehyde) slim soft-closing seat cover, anti-bacterial glaze, concealed wall mounting bolts/chair bracket fixings, rubber buffers, and EPDM inlet/outlet gaskets. All work executed strictly as per manufacturer’s details and architectural drawings. EACH

6 M.R Supplying and fixing CP (Chrome Plated) brass 2-Way Bib Cock with wall flange, manufactured from forged brass ingots confirming to IS:1264/IS:319 with minimum 10-micron nickel and 0.3-micron chromium plating. Suitable for simultaneous connection of health faucet and regular spout outlet, fitted with quarter-turn high endurance ceramic disc cartridge (tested up to 500,000 cycles) and foam flow aerator. EACH

7 M.R Providing and fixing CP brass standard Bib Cock with decorative wall flange, heavy forged body, high performance quarter-turn ceramic spindle, and splash-free honeycomb aerator, including sealing with Teflon tape, complete in all respects EACH

8 M.R Supplying and fixing Health Faucet (Hand Spray Jet) assembly with easy-to-operate trigger lever, complete with 1.0-meter long chrome finish flexible EPDM/braided hose (Easy Flex Tube), matching wall hook/bracket, rubber seals, and CP brass wall connection nuts. EACH

9 M.R Supplying and fixing wall-mounted Toilet Paper Roll Holder with protective Flap cover, made of corrosion-resistant CP brass / SS alloy, anchored firmly into masonry/tile using SS screws, rawl plugs, and concealed fixing base plates. EACH

10 M.R Providing, fixing, and testing concealed/exposed 32 mm / 40 mm nominal bore heavy forged brass Flush Valve with square/round wall flange, complete with chrome finish operating push plate/lever mechanism, rubber seals, and control stop cock. EACH

11 M.R Supplying and fixing table-top / wall-hung Vitreous China Wash Basin in alpine white finish, having smooth glazed non-porous surface, pre-punched single tap hole and overflow slot, complete with heavy-duty MS/CI fixing brackets, anchor fasteners, and sealing around edges with anti-fungal silicone sealant. EACH

12 M.R Supplying and fixing wall-mounted Liquid Soap Dispenser, consisting of heavy frosted glass container/bottle, chrome plated brass pump mechanism with anti-drip nozzle, and matching CP brass mounting ring secured with concealed screws. EACH

13 M.R Supplying, fixing, and testing of table/deck mounted CP (Chrome Plated) brass Pillar Cock / Single Lever Basin Mixer, manufactured from extruded/forged brass conforming to IS:1264 / IS:319 with high corrosion-resistant nickel-chromium plating. Complete with quarter-turn high endurance ceramic disc cartridge, splash-free honeycomb foam-flow aerator, complete pop-up waste assembly, fixing nut-bolts, rubber washers, and a pair of 450 mm long stainless steel (AISI 304) wire-braided flexible connection pipes. All installed complete as per manufacturer's specification and site engineer's instructions EACH

14 M.R Providing and fixing 32 mm nominal size heavy duty CP brass Full-Threaded Waste Coupling (80 mm overall height) with slotted overflow design, tight-fit rubber gasket, and brass check nut, suitable for wash basins EACH

15 M.R Supplying and fixing 32 mm size heavy forged CP brass Bottle Trap with detachable base cup for cleaning, complete with 250 mm horizontal wall connection pipe, 190 mm vertical inlet extension pipe, rubber seals, and CP wall flange. EACH

16 M.R Supplying and fixing architectural square design CP brass Towel Ring, with concealed wall mounting bracket, grub screw locking system, and chrome plated finish. EACH

17 M.R Providing and fixing 15 mm nominal bore CP brass Angle Stop Cock with wall flange, featuring quarter-turn movement, ceramic headwork, and standard male threaded inlet/outlet. EACH

18 M.R Providing and fixing 15 mm NB heavy forged internal / concealed Angle Cock / Control Valve with threaded connections and wall flange, suitable for hot/cold water supply lines behind plumbing fixtures. EACH

19 M.R Providing and fixing single/multi-flow ABS chrome-finished Hand Shower with anti-clogging silicone rub-clean spray jets, accompanied by heavy flexible tube (1.5 m length) and wall-mounted articulated swivel hook/bracket. EACH

20 M.R Supplying and fixing 240 x 240 mm Square Shape Maze Overhead Rain Shower, body and face plate made of high-grade AISI 304 Stainless Steel in mirror chrome finish, equipped with advanced 'Rubit' cleaning technology nozzles to prevent lime scale buildup, ball-joint swivel connector, matching square CP brass shower arm, and heavy wall flange. EACH

21 M.R Supplying & Placing executive table in completely knock down conditions with an overall size 1600mm X 1600mm X 750mm that is to be assembled at site. The worktop shall be made up of 25mm thick Pre-laminated particle board of grade II of IS 12823 with approved laminate and finish as per approved shade. The profile shall be in rectangle shape and the edges shall be sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree Celsius. The top shall be supported on MS powder coated rectangle pipe frame having cross-section area 40mm X 20mm. The table shall be clad with 1mm thick modesty panel which provide structural support for the table. It should be 1mm thick with star perforation CRCA powder coated sheet in linear shape. The understructure shall consist of loop leg and C leg made up of MS powder coated triangular shape pipe having cross-section area 53mm X 53mm X 75mm. There shall be shoe provided to avoid scratches on the floor. Side top shall be provided with an overall size 800mm X 500mm X 750mm made up of 25mm thick Pre-laminated particle board of grade II of IS 12823. It shall be supported on peg which is mounted over side storage unit. The side storage having an overall size 1400mm X 570mm X 500mm. It should be made up of particle board with drawer base 9mm thick and other parts 18mm thick like shutter, back, facia, side panel etc. It shall have 2 box drawer, 1 filing drawer and 1 door shutter. The drawer shall be operated with roller channel and ball bearing channel to enable smooth operation. The drawer shall have central locking mechanism in which all the drawer shall be synchronized locked with one single key. The shutter shall be operated by handle and concealed crank hinge. Side storage unit shall be mounted on CRCA powder coated U shape leg having cross-section area 53mm X 53mm x 75mm. The manufacturer shall have quality and safety assurance like ISO-9001:2015, ISO-14001:2015 and ISO-18001:2007, BIFMA membership and AIOTA certification. The board used should meet International Standard of quality, Indian standard IS 12823 grade II should meet long time load bending, screw-withdrawal strength, modulus of rupture and modulus of elasticity bending tested as per IS 2380.Warranty-5 Years. EACH

22 M.R Supplying & Placing executive table with ERU unit in completely knock down conditions with an overall size 1650mm X 1650mm X 750mm that is to be assembled at site. The worktop shall have the combination of 18mm PLPB and 25mm MDF board. The top shall have the size 1650mm X 750mm made up of 18mm thick Pre- laminated particle board of grade II of IS 12823 with approved laminate laminate and finish as per approved shade. The base top shall have the size 1650mm X 750mm made up of 25mm thick Medium density fibre-board with deco painted. The top profile shall be in rectangle shape with front half round shape and the edges shall be sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree Celsius and base top with half round post forming edges. The top shall be supported on 75mm MS powder coated U-clamp. The end wall of the table on the side shall be topped by gable end. It should be made up of 36mm thick Pre-laminated particle board and profile shall be in linear shape with appropriate PVC edge banding. The table shall be clad with 18mm thick modesty panel which provide structural support for the table. It should be 18mm thick pre-laminated particle board in linear shape with appropriate PVC edge banding connected with both end. There shall be buffers provided at the bottom to avoid scratches on the floor. The side top shall be provided with an overall size 900mm X 450mm X 750mm. It should have the combination of 18mm PLPB and 25mm MDF. Side top shall be supported on 75mm Peg which mounted over side pedestal unit. The table shall have side unit for storage purpose with an overall size 850mm X 400mm X 645mm. The side unit shall be made up of Pre-laminated particle board of grade II of IS 12823 with base 9mm thick and other parts 18mm thick like shutter, back, facia, side panel etc. It shall have 3 nos. of drawer having same size, 1 nos. of door shutter operated with the assistance of SS handle, easily close & open with roller channel and ball bearing channel to enable smooth operation and concealed crank hinge. The drawer shall have central locking mechanism in which all the drawer shall be synchronized locked with one single key. To protect the wall from kicks, abrasion and serve as a decorative moulding, skirting shall be provided at bottom. Fixed pedestal shall be provided with an overall size 400mm X 450mm X 645mm. It should be made up of Pre-laminated particle board of grade II of IS 12823. Pedestal side, back, top, facia shall be 18mm thick and drawer base shall be 9mm thick. The pedestal shall have 3 nos. of drawer i.e. 2 box drawer and 1 filing drawer operated with SS handle and sliding channel. The drawer shall have central locking mechanism in which all the drawer shall be locked with one single key. The manufacturer shall have quality and safety assurance like ISO-9001:2015, ISO-14001:2015 and ISO- 18001:2007, BIFMA membership and AIOTA certification. The board used should meet International Standard of quality, Indian standard IS 12823 grade II should meet long time load bending, screw-withdrawal strength, modulus of rupture and modulus of elasticity bending tested as per IS 2380.Warranty-5 Years. EACH

23 M.R Providing and supplying high back chair. The seat and back shall be made up of wooden and plywood frame padded with high resilience polyurethane foam having density 45Kg/m³ in seat and 40Kg/m³ in back. The same shall be upholstered with leatherette tapestry 1mm thick. The backrest of the chair shall be made by keeping the natural curvature of the spine for lumbar support. The armrest shall be used chrome plated arm with cushion top. The back of the chair shall be recline with the assistance of push knob suituated at right side of the chair. For seating durability the chair shall have torsion bar 360 degree revolving mechanism with upright position locking and tilt tension adjustment. The pneumatic seat height adjustment for healthy seating user can adjust seat height up to 65mm with BIFMA standard class-3 chrome plated gas-lift to suit them using the lever under the seat. The gas- lift mechanism should be tested as per ANSI/BIFMA X5.1-2011 standard. The pedestal should have five legged die cast aluminium having pitch circle Dia. 640 mm fitted with 5 nos. twin wheel castors. The castors of the chair should be injection moulded in black 30% glass filled nylon, confirming to ANSI/BIFMA standard X5.1-2011 tested to perform 98,000 cycles with 250lbs load. The seat size shall be 530±10 mm(W) X 470±10 mm(D) and back size shall be 500±10 mm(W) X 720±10 mm(H) from seat. Overeall Height shall be 1200mm and overall Width/Depth shall be 680mm.Warranty-5 Years. EACH

24 M.R Providing and supplying medium back chair with ergonomic design, comfortable & aesthetically appealing. The seat shall be made of 15mm thick hot pressed plywood upholstered with high resiliance moulded polyurethane foam 40mm thick having density 40kg/m³ with leatherite tapestry 0.8mm thick and 535 GSM and the back shall be made of metal bright bar upholstered with breathable mesh and leatherite tapestry 0.8mm thick and 535GSM. The chair shall be supplied with polyurethane arm mounted on metal pipe loop frame. For seating durability the chair shall have swivel tilt 360 degree revolving mechanism with upright position locking and tilt tension adjustment. The pneumatic seat height adjustment for healthy seating, user can adjust seat height up to 100mm with BIFMA standard class-3 gas-lift to suit them using the lever under the seat. The gas-lift mechanism should be tested as per ANSI/BIFMA X5.1-2011 standards. The pedestal should have five legged MS/CRCA chrome plated having pitch circle Dia. 650 mm fitted with 5 nos. twin wheel castors. The castors of the chair should be injection moulded in black nylon 30% glass filled, confirming to ANSI/BIFMA standard X5.1-2011 tested to perform 98,000 cycles with 250lbs load. The seat size shall be 470±10 mm(W) X 475±10 mm(D) and back size shall be 550±10 mm(H) from seat & overall height = 960±10 mm.Warranty-5 Years. EACH

25 M.R Supplying & Placing Visitor Chair. The seat and back shall be made of molded PU padded with high resilience polyurethane foam 40mm thick having density 40kg/m³ in seat and 25mm thick having density 32kg/m³ in back. The sae shall be upholstered with fabric tapestry 0.6mm thick. The seat and back shall be arrested together with the armrest. The frame structure shall be supported by four legs made up of MS/CRCA chrome plated pipe of size 30mmx15mm with 1.6mm thick. There shall be PPCP shoe provided at the base to avoid scratches on the floor. The seat size shall be 465±10 mm(D) X 500±10 mm(W) and back size shall be 460±10 mm(W) X 360±10 mm(H) from seat. Overall height shall be = 790±10 mm, overall depth = 560±10 mm & overall width = 550±10mm.Warranty-5 Years. EACH

26 M.R Supplying & Placing Conference table in completely knock down conditions with an overall size 3600mm X 1200mm X 750mm that is to be assembled at site. The top shall be made up of 25mm thick pre-laminated particle board of grade II of IS 12823 with approved laminate and finish as per approved shade. The profile shall be in rectangle shape and the edges shall be sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree Celsius. The top shall be supported on MS/CRCA triangular shape pipe frame having cross-section area 53mm X 53mm X 75mm. The understructure shall consist of MS/CRCA triangular shape leg having cross-sectional area 53mm X 53mm X 75mm. The metal part shall be powder coated to the thickness of 40-60µ DFT. There shall be plastic shoe provided to avoid scratches on the floor. The table connections have to be made in such a way that no gap should be seen in between. The manufacturer shall have quality and safety assurance like ISO-9001:2015, ISO-14001:2015 and ISO-18001:2007, BIFMA membership and AIOTA certification. The board used should meet International Standard of quality, Indian standard IS 12823 grade II should meet long time load bending, screw-withdrawal strength, modulus of rupture and modulus of elasticity bending tested as per IS 2380.Warranty-5 Years. EACH

27 M.R Supplying & Placing workstation table in completely knock down conditions with an overall size 2000mm X 1260mm X 1200mm that is to be assembled at site. The worktop shall be made up of back to back 25mm thick Pre- laminated particle board of grade II of IS 12823 with approved laminate and finish as per approved shade. The top profile shall be in sharing base rectangle shape and the edges shall be sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree Celsius. A pullout keyboard trey shall be provided of 18mm thick Pre-laminated particle board having size 550mm X 280mm. The trey shall be operated on keyboard channel. The top shall be supported on particle board base gable end. The end wall of the top on the side shall be topped by gable end. It should be made up of 25mm thick Pre-laminated particle board and the profile shall be in linear shape with appropriate PVC edge banding. The workstation shall have panel based partition of 60 mm thick with overall height 1200mm. The partition shall be linear in profile and provided in front side of user. The top trim, top bar, mid bar, vertical bar, raceway, skirting shall be made up of aluminium extrusions (pre-treated) and duly powder coated with 40-60µ thick. The trims shall have the size 60mm X 19mm with 1.5mm thick covered with Die cast end caps on joints 2 ways, 3 ways & 4 ways (L-cover for corner, T-cover for middle section wherever required). The aluminium raceway shall be situated below the worktop with an overall size 116mm(H) X 60mm(D) with 1.4 mm cover thickness and 2mm back thickness as per requirement of inlaying the electrical management and carrying the wire horizontally. The exposed vertical and horizontal faces of the frames shall be snap fitted with trims. There shall be soft-board (with fabric) provided at front of the user. Laminated bottom tile shall be situated below the work top. The Partition shall have concealed wire management capabilities and should be engaged for responsive and safe operations of power, telecommunications and data (LAN) and has separate components for electrical, data and telephone cables having adequate capability of both the vertical and horizontal wire movements. Slots/cut-outs should be given on raceways to fix all electrical and data points. Zinc coated small top support brackets shall be fixed on the partition for table top support. To protect the wall from kicks, abrasion and serve as a decorative moulding, skirting shall be situated at bottom. Adjustable leveller shoe shall be provided at bottom of the partition to avoid scratches on the floor. Fixed pedestal shall be provided with an overall size 400mm X 450mm X 725mm. The pedestal shall be made up of Pre-laminated particle board of grade II of IS 12823. Pedestal side, back, top, facia shall be 18mm thick and drawer base shall be 9mm thick. The pedestal shall have 4 nos. of drawer having same size. The drawer shall be operated with SS handle and easily close & open with the assistance of roller channel to enable smooth operation. The drawer shall have central locking mechanism in which all the drawer shall be synchronized locked with one single key. To protect the wall from kicks, abrasion and serve as a decorative moulding, skirting shall be provided at bottom. A nylon castor based CPU unit shall be provided with an overall size 470mm X 286mm with 18mm thick Pre-laminated particle board. The manufacturer shall have quality and safety assurance like ISO-9001:2015, ISO-14001:2015 and ISO-18001:2007, BIFMA membership and AIOTA certification. The board used should meet International Standard of quality, Indian standard IS 12823 grade II should meet long time load bending, screw-withdrawal strength, modulus of rupture and modulus of elasticity bending tested as per IS 2380.Warranty-5 Years. EACH

28 M.R Providing and supplying mid back chair. The seat shall be made of 15mm thick hot pressed commercial plywood upholstered with high resilience moulded polyurethane foam 50mm thick having density 45kg/m³ with fabric tapestry 1mm thick and 300 GSM and the back shall be made of plastic inner upholstered with high resilience moulded polyurethane foam 25mm thick having density 32kg/m³ with fabric tapestry 1mm thick and 300 GSM. The back and base shall be supplied with injection moulded polypropylene outer cover. The armrest shall be used polypropylene loop arm completely joint with seat. For seating duranility the chair shall have synchro tilt 360 degree revolving mechanism with upright position locking and tilt tension adjustment. The pneumatic seat height adjustment for healthy seating, user can adjust seat height up to 100mm with BIFMA standard class-3 gas-lift to suit them using the lever under the seat. The gas-lift mechanism should be tested as per ANSI/BIFMA X5.1-2011 standard. The pedestal should have five legged injection moulded in 30% glass filled black nylon having pitch circle Dia. 650 mm fitted with 5 nos. twin wheel castors. The castor of the chair should be injection moulded in black nylon 30% glass filled, confirming to ANSI/BIFMA X5.1-2011 standard tested to perform 98,000 cycles with 250lbs load. The seat size shall be 455±10 mm(D) X 490±10 mm(W) and back size shall be 460±10 mm(W) X 450±10 mm(H) from seat. Overall height shall be = 880±10 mm, base width/ depth = 710±10 mm.Warranty-5 Years. EACH

29 M.R Supplying & Placing executive table in completely knock down conditions with an overall size 1200mm X 600mm X 750mm that is to be assembled at site. The construction of the main table shall be free standing structure constructed with the help of minifix dowels and pins. The table top shall be made up of 25mm thick particle board with approved laminate and finish as per approved shade. The profile shall be in rectangle shape with one side post forming edges. The top shall be supported over particle board base gable end. The end wall of the table on the side shall be topped by gable end. It should be made up of 18mm thick particle board and profile shall be in linear shape. The table shall be clad with 18mm thick modesty panel which provide structural support for the table. It shall be 18mm thick particle board with appropriate PVC edge banding connected with both end. There shall be buffers provided at the base to avoid scratches on the floor. One hanging drawer shall be provided with an overall size 400mm X 450mm X 150mm with key locking mechanism. The drawer shall be made up of Pre-laminated particle board of grade II of IS 12823. Drawer side, back, top, facia shall be 18mm thick and drawer base shall be 9mm thick. The drawer shall be operated with Al die cast handle and easily close & open with the assistance of ball bearing channel to enable smooth operation. The manufacturer shall have quality and safety assurance like ISO-9001:2015, ISO-14001:2015 and ISO- 18001:2007, BIFMA membership and AIOTA certification. The board used should meet International Standard of quality, Indian standard IS 12823 grade II should meet long time load bending, screw- withdrawal strength, modulus of rupture and modulus of elasticity bending tested as per IS 2380.Warranty-5 Years. EACH

30 M.R Supplying & Placing single seater bench. The seat and back shall be made up of high quality SS 202/304 grade perforated sheet of 1.2mm thick, pressed and welded to form the shape. The armrest shall be made up of SS202/304 . The base structure shall be supported by SS 202/304 . There shall be PPCP shoe provided at the base to avoid scratches on the floor.The main frame shall be made up of ms/crca powder coated in 16 gauge . The seat size shall be 440±10 mm(D) X 405±10 mm(H) from ground. Overall height shall be = 755±10 mm, overall depth = 710±10 mm & overall width = 1750±10 mm.Warranty-5 Years. EACH

31 M.R Supplying and Placing Magazine Rack, Overall Dimensions of All Steel Periodical Display Rack shall be 900mm(W)x450mm(D)x1850mm(H). Rigid Knockdown construction ,Panels shall be made from CRCA 0.8 mm thick and front frame shall be made from CRCA 0.8 mm thick . CRCA D grade as per IS 513 . There shall be 5 level racks , Display tray shall be suitable for fullscape size magazines,periodicals, aesthetically appealing metal tray at an angle for easy viewing . Receding facility to access the storage behind . Sliding on plastic rollers . Behind storage shelving each of 5 level has a behind storage shelf . Uniformly Distributed Load capacity per each shelf is 40 kg . Leveler shall be screw type with hex plastic base and finish shall be epoxy polyester powder coated to the thickness of 50 microns .Warranty-5 Years. EACH

32 M.R Providing, supplying and placing steel Almirah. The overall size of the Almirah shall be 900mm (W) X 450mm (D) X 1830mm (H). The cabinet shall be supplied with 2 nos. of doors and 4 nos. of adjustable shelves. The doors shall be operated with aesthetically appealing snap fit ABS plastic handle and concealed crank hinge. The shelves shall have folded constructions which have intrinsic rigidity and high load carrying capacity. Uniformly distributed load capacity of each shelf shall be 40 Kg maximum. Each rack shall be provided with stiffener at bottom for strength. The entire body panel, shelf shall be made of high yield strength 0.8mm thick CRCA sheet of grade ‘D’ confirming to IS: 513. To protect the ball from kicks, abrasion and serve as a decorative moulding skirting shall be provided at the bottom of the Almirah. The complete steel structure shall be constructed by welding and provide finishing with epoxy polyester powder coated to the thickness 40-60µ thick.Warranty-5 Years. EACH

33 M.R Supplying & Placing Conference table in completely knock down conditions with an overall size 3600mm X 1200mm X 750mm that is to be assembled at site. The construction of the main table shall be free standing structure constructed with the help of minifix, dowels, pins and brackets. The worktop shall have the combination of PLPB board and MDF board. The main top should be made up of back to back 18mm thick Pre-laminated particle board of grade II of IS 12823 with approved laminate and the base top shall be made up of 25mm thick Medium density fibre-board with deco matt finish. The table top profile shall be boat like shape with round corners. The edges edges shall be sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree Celsius and the base top shall be with half round post form with grooves. Single sided Flip-up box should be enclosed at table top that houses video, audio, data and power connection discretely. Wire carrier shall be provided below the table top for power connection made of 0.8mm thick high yield strength CRCA sheet of grade 'D' confirming to IS:513. The table shall be supported on particle board base gable end. The end wall of the table on the side and mid shall be topped by gable end. It should be made up of 36mm thick Pre-laminated particle board and profile shall be in linear shape with appropriate PVC edge banding. The table shall be clad with 18mm thick modesty panel which provide structural support for the table. It should be 18mm thick Pre-laminated particle board with appropriate PVC edge banding connected with both end. There shall be buffers provided at the base to avoid scratches on the floor. The table connections have to be made in such a way that no gap should be seen in between. The manufacturer shall have quality and safety assurance like ISO-9001:2015, ISO-14001:2015 and ISO-18001:2007, BIFMA membership and AIOTA certification. The board used should meet International Standard of quality, Indian standard IS 12823 grade II should meet long time load bending, screw-withdrawal strength, modulus of rupture and modulus of elasticity bending tested as per IS 2380.Warranty-5 Years. EACH

34 M.R Providing and supplying visitor chair with ergonomic design for user comfort. The seat and back shall be made of hot pressed commercial plywood padded with high resilience polyurethane foam having density 40Kg/m³ in seat and 32kg/m³ in back. The same shall be upholstered with leatherite tapestry 0.8mm thick and 35 GMS. The backrest of the chair shall be made by keeping the natural curvature of the spine for lumbar support with the assistance of cushion. The armrest shall be used cushion arm with leatherite covering top mounted on injection moulded ABS chrome holder. The frame structure shall be cantilever support type made up of MS/CRCA chrome plated rectangle pipe having cross- section area 30mm X 20mm with 2mm thick. There shall be co-polymer polypropylene shoe provided at the base to avoid scratches on the floor as well as uneven surfacing. The seat size shall be 510±10 mm(W) X 450±10 mm(D) and back size shall be 480±10 mm(W) X 520±10 mm(H) from seat & overall height = 955±10 mm, overall width = 650±10 mm & overall depth = 635±10 mm.Warranty-5 Years. EACH

35 M.R Supplying & Placing Visitor Chair. The seat shall be made of double layered (12+6)mm thick hot pressed plywood with HR polyurethane foam 50mm thick having density 40kg/m³ upholstered with fabric tapestry 0.6mm thick and 235 GSM and the back shall be made of hot pressed plywood 12mm thick with HR softy polyurethane foam 12mm thick having density 23kg/m³ upholstered with fabric tapestry 0.6mm thick and 235 GSM. There shall be L type ply used. The armrest shall be used PP arm mounted on metal pipe frame completely joint with seat and back. The frame structure shall be cantilever support type made up of MS/CRCA powder coated with 40-50µ (DFT) thick round pipe of Dia 25.4mm with 2mm thick. There shall be PPCP shoe provided at the base to avoid scratches on the floor. The seat size shall be 460±10 mm(W) X 505±10 mm(D) and back size shall be 400±10 mm(H) from seat & overall height = 850±10 mm.Warranty-5 Years. EACH

36 M.R Providing, supplying, placing and Installation of Water cooler cum purifier RO+UV+CUZN technology with 120 ltrs storage, Approximate External Dimensions (WXDXH) 750 x 690 x 1420 mm, Input Voltage 230 V AC (50 Hz), Power Rating (Max) 850 ± 10%, Water Storage Tank Capacity 120 Ltr., Cooling Capacity at Comfort Level 80 LPH, Water Outlet Temperature at rated condition 17°C±1°C, Refrigerant HFC R 134 a, Thermal Insulation for Storage Tank PUF, No. of Faucets 3 Cold, No. of Stages for Filter cum Purifier 7, Active Copper Zinc Booster, 25% of Purified Water Recovery, 90% Rejection of TDS, 50 LPH Permeate (Purified Water) Production Capacity, SS 304 Storage Tank & Drain Tray Material, Front Panel SS 304 and rest CRCA Powder Coated Steel, Concealed Product Construction type, Indoor Installation, net wt 92 Kgs, 1.0 to 2.0 Kg/cm² Operating Input Water Pressure, 10°C to 45°C Operating Temperature, Recommended Total Dissolved Solids in Input Water(TDS) 500 to 2000 ppm.(Max), Recommended Hardness in Input Water 500 ppm with Antiscalent*, Recommended Ph of Input Water 6.5 to 8.5, Allowable Chlorine Input Water 0.2 ppm (Max), Allowable Iron in Input Water 0.3 ppm (Max), Turbidity <5 NTU, SDI (Silt Density Index) <5.Warranty-5 Years. EACH

37 M.R Supplying & Placing Modular table in completely knock down conditions with an overall size 2450mm X 2200mm X 750mm that is to be assembled at site. The worktop shall have the size 2200mm X 1000mm x 76mm thick made up of Medium Density Fibre-board with approved veneer laminate and PU polish accordingly. The table top profile shall be in rectangle shape with round corners and full round post forming edges. The table top shall be supported on MDF board based gable end. The end wall of the table on the side shall be topped by gable end. It should be made up of 76mm thick medium density fibre-board and profile shall be in moulded construction with full round post forming edges and duly deco painted. The table shall be clad with 18mm thick modesty panel which provide structural support for the table. It should be 18mm thick medium density fibre-board in linear shape with appropriate PVC edge banding and veneer laminate. There shall be buffers provided at the base to avoid scratches on the floor. The table shall have side unit for storage purpose with an overall size 2200mm x 600mm X 600mm. It shall have 2 nos. of drawer, 1 nos. of filling space with door and 1 nos of open space . The drawer shall be operated with profile handle and easily close & open with the assistance of sliding channels to enable smooth operation and sliding rail track and concealed crank hinge. Drawer facai, sides and all other shall be made in 18mm thick and drawer base shall be 9mm thick. To protect the wall from kicks, abrasion and serve as a decorative moulding, skirting shall be provided at bottom. The complete structure shall be supplied with approved veneer laminate, PU polish and deco painted. The manufacturer shall have quality and safety assurance like ISO-9001:2015, ISO-14001:2015 and ISO-18001:2007, BIFMA membership and AIOTA certification.Warranty-5 Years. EACH

38 M.R Providing and supplying a high back chair with ergonomic design, comfortable & aesthetically appealing. The seat shall be made of 15mm thick hot pressed commercial plywood padded with high resilience polyurethane foam (50+25)mm thick having density 40kg/m³ and the back shall be made of (15+6)mm thick double layered moulded plywood padded with high resilience polyurethane foam 40mm thick having density 32kg/m³. The seat and back shall be upholstered with leatherite tapestry 0.8mm thick and 535 GSM. The backrest shall be made by keeping the natural curvature of the spine which helps to provide full back support as well as head support. The chair shall be supplied with Chrome plated with cushion arm having leatherite top completely joint with seat. For seating durability the chair shall have synchro knee tilt 360 degree revolving mechanism with four position locking and tilt tension adjustment which provides back strength for the chair. The pneumatic seat height adjustment for healthy seating, user can adjust seat height up to 65mm with BIFMA standard class-3 gas-lift to suit them using the lever under the seat. The gas-lift mechanism should be tested as per ANSI/BIFMA X5.1-2011 standards. The Pedestal should have five legged made of die cast aluminium having pitch circle dia. 700 mm fitted with 5 nos. twin wheel castors. The castors of the chair should be injection moulded in black 30% glass filled nylon, confirming to ANSI/BIFMA standards X5.1-2011 tested to perform 98,000 cycles with 250lbs load. The seat size shall be 500±10 mm(D) X 530±10 mm(W) and back size shall be 540±10 mm(W) X 750±10 mm(H) from seat. Overall height shall be = 1210±10 mm, overall depth = 630±10 mm & overall width = 650±10 mm.Warranty-5 Years. EACH

39 M.R Supplying & placing Back storage unit with an overall size 2250mm X 450mm X 2200mm. It should be made up of 18mm thick Pre-laminated particle board of grade II of IS 12823 with approved laminate and finish as per approved shade with extruded Aluminium profile. All profile i.e. side, back, shutter, shelf, skirting shall be 18mm thick and the edges shall be sealed with thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree celsius. The storage shall have shelves and 8 nos. of door shutter for ease of opening. The shutter shall be operated with concealed crank hinge and die cast handle. There shall be legs provided at the bottom to avoid scratches on the floor. The manufacturer shall have quality and safety assurance like ISO-9001:2015, ISO-14001:2015 and ISO-18001:2007, BIFMA membership and AIOTA certification. The boards used should meet international standards of quality and safety, Indian standard IS 12823 grade II should meet long time load bending, screw-withdrawal strength, modulus of elasticity bending tested as per IS 2380.Warranty-5 Years. EACH

40 M.R Supplying and placing two seater sofa that shall be constructed from natural hard wood and commercial plywood having inner frame. The thickness of the wood should allow for the heavy tension webbing. The sofa shall have spring attached and also be padded separately. The frame shall be padded with high resilience polyurethane foam having density 45Kg/m³ in seat and 32Kg/m³ in back. There shall be cushion arm provided padded with high resilience polyurethane foam having density 32Kg/m³. The armrest shall be flap with soft cushion on both side for aesthetically appealing as well as side comfort. The complete structure shall be upholstered with leatherite tapestry 0.8±0.1 mm thick and 535 GSM. The understructure shall have MS powder coated frame having thickness 8mm. There shall be buffers provided at the bottom to avoid scratches on the floor as well as uneven surfacing. The seat size shall be 980±10 mm(W) X 530±10 mm (D) X 380±10 mm (H). Overall width = 1525±10 mm, overall depth = 830±10 mm & overall height = 860±10 mm.Warranty-5 Years. EACH

41 M.R Supplying & placing center table with an overall size 1200mm X 600mm X 450mm. The top shall be made up of 12mm thick toughened glass. The top profile shall be in rectangle shape with bevelled edges. The understructure shall consist of MS/CRCA rectangle pipe frame having cross-section area 30mm X 15mm with 1.6mm thick duly powder coated with 40-60µ dy film thickness.Warranty-5 Years. EACH

42 M.R Supplying & placing center table with an overall size 900mm X 900mm X 450mm. The top of the table shall be made up of 25mm thick Pre-laminated particle board of grade II of IS 12823 with approved laminate and shade. The top profile shall be in square shape and the edges shall be sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree Celsius. The top shall be supported on MS rectangle pipe frame with cross-section area 40mm X 20mm with 1.6mm thick. The under structure shall consist of MS/CRCA four legs having Dia. 38mm at upper and 28mm at lower. There shall be co-polymer polypropylene shoe provided at the bottom to avoid scratches on the floor. The manufacturer shall have quality and safety assurance like ISO-9001:2015, ISO-14001:2015 and ISO-18001:2007, BIFMA membership and AIOTA certification. The board used should meet International Standard of quality, Indian standard IS 12823 grade II should meet long time load bending, screw-withdrawal strength, modulus of rupture and modulus of elasticity bending tested as per IS 2380.Warranty-5 Years. EACH

43 M.R Providing, supplying and placing steel almirah. The overall size of the Almirah shall be 900mm (W) X 450mm (D) X 1830mm (H). The Almirah shall be supplied with 2 nos. of glass door and 2 nos. of steel door with adjustable shelves. The door shall be operated with aesthetically appealing snap fit ABS plastic handle and concealed crank hinge. The glass shall be used 4mm thick clear. The shelves shall have folded constructions which have intrinsic rigidity and high load carrying capacity. Uniformly distributed load capacity of each shelf shall be 40 Kg maximum. Each rack shall be provided with stiffener at bottom for strength. The entire body panel, shelf shall be made of high yield strength 0.8mm thick CRCA sheet of grade ‘D’ confirming to IS: 513. To protect the ball from kicks, abrasion and serve as a decorative moulding skirting shall be provided at the bottom. The complete steel structure shall be constructed by welding and provide finishing with epoxy polyester powder coated to the thickness 40-60µ thick.Warranty-5 Years. EACH

44 M.R Supplying & Placing Computer table in completely knock down conditions with an overall size 900mm X 600mm X 750mm that is to be assembled at site. The construction of the main table shall be free standing structure constructed with the help of minifix dowels and pins. The table top shall be made up of 25mm thick particle board with approved laminate and finish as per approved shade. The profile shall be in rectangle shape with one side post forming edges. The top shall be supported over particle board base gable end. The end wall of the table on the side shall be topped by gable end. It should be made up of 18mm thick particle board and profile shall be in linear shape. The table shall be clad with 18mm thick modesty panel which provide structural support for the table. It shall be 18mm thick particle board with appropriate PVC edge banding connected with both end. There shall be buffers provided at the base to avoid scratches on the floor. One hanging drawer shall be provided with an overall size 400mm X 450mm X 150mm with key locking mechanism. The drawer shall be made up of Pre-laminated particle board of grade II of IS 12823. Drawer side, back, top, facia shall be 18mm thick and drawer base shall be 9mm thick. The drawer shall be operated with Al die cast handle and easily close & open with the assistance of ball bearing channel to enable smooth operation. The manufacturer shall have quality and safety assurance like ISO-9001:2015, ISO-14001:2015 and ISO- 18001:2007, BIFMA membership and AIOTA certification. The board used should meet International Standard of quality, Indian standard IS 12823 grade II should meet long time load bending, screw- withdrawal strength, modulus of rupture and modulus of elasticity bending tested as per IS 2380.Warranty-5 Years. EACH

45 M.R Suplying and placing of Single bed, Overall Size: Width- 1131 mm Depth— 2050 mm Height -930 mm Material:Bed Structure conssst of metal frames made of M S. Channels in Imm Thickness.Horizontal plinths and bottom plinth are made of 25 mm Thick Prelaminated Particle Board 1S:12823 Class E1 (as per EN13986). Head board is made of 18 mm thick Prelaminated Particle board 1S:12823 Class E1 (as per EN13986) with all the exposed edges are edge banded with 0.8 mm thick PVC edge banding glued with Hot Melt EVA glue.Tailboard is made of 18 mm thick Prelaminated Particle board 1S:12823 Class E1 (as per EN13986).Side rail is made of 18 mm thick Prelaminated Particle board 1S:12823 Class E1 (as per EN13986).Mattress panels of Bed are made of 18 mm thick Prelaminated Particle Board IS: 12823 Class E1 (as per EN13986) with all the exposed edges are edge bandedwith 0.8 mm thick PVC edge banding glued with Hot Melt EVA glue.Hardware:The high quality hardware are used.Construction: Knock Down construction. Packets :2 packet.Finish :.18 mm thick Prelaminated Particle Board 1S:12823 Class E1 (as per EN13986)is in Imperial Oak shade. Lipping shade is 299P . Company should be ISO-9001, 14001, 45001, 50001, BIFMA, AIOTA and Greenguard certified.Warranty-5 Years. EACH

46 M.R Supply of premium quality mattress of overall size 1981 mm × 1829 mm (±10 mm), minimum thickness 100 mm, made of high-density PU foam/rebonded foam with quilted fabric cover. Outer fabric shall be breathable, anti-dust mite, wrinkle-resistant and washable. Mattress shall provide uniform support with reinforced edges and shall be suitable for institutional use. Warranty-5 Years. EACH

47 M.R Supply of premium quality cotton pillow of size 330 mm × 560 mm (±10 mm). Pillow shall be filled with soft, resilient virgin polyester/cotton fibre providing adequate neck support. Outer cover shall be 100% cotton fabric with stitched edges and washable finish. Pillow shall be hygienic, odour-free and suitable for institutional use.Warranty-5 Years. EACH

48 M.R Supply of handloom cotton bed sheet of size 2290 mm × 1400 mm (±20 mm) made from 100% cotton fabric with colour-fast finish. Fabric shall be soft, shrink-resistant and washable. All edges shall be neatly hemmed. Suitable for regular institutional use.Warranty-5 Years. EACH

49 M.R Providing and supplying dressing table complete with mirror, drawers and storage cupboard. Overall construction shall be made from 18 mm thick Pre-Laminated Particle Board (PLPB) conforming to IS:12823, with 2 mm PVC edge banding on exposed edges. Back panel shall be minimum 9 mm thick MDF/Particle Board. Mirror shall be 5 mm thick clear float glass with polished edges. Hardware shall include telescopic drawer channels, SS/CP handles, concealed hinges, magnetic catcher, lock with keys and adjustable levelling bushes. Finish shall be scratch-resistant, moisture-resistant and termite-resistant. Colour shall be selected by the Engineer-in-Charge from the manufacturer's standard shades. Complete in all respects.Warranty-5 Years. EACH

50 M.R "SITC of POE+ Layer 2 Fully Manageable Network Switch consists of Fixed 1RU chassis 24 PoE 1G BaseT, 6 fixed 1G/10G SFP+ uplink/VFL ports. Internal AC PSU (380 budget), includes country specific power cord, guides and 19"" rack mount kit. Inclusive of stacking cable.The detailed Specification as follows. ; Approved Make : Cisco/ Nexxus / Extreme/ Arista/Juniper " Minimum specification 24 X 1G RJ-45 PoE+ Ports with 370W power budget 6x 1G/10G SFP+ Ports Internal Power Supply , RPS AC and DC PSU Mix environmnet for power source resiliency . Upto 12 Switches or more 1 GB or better 1 GB or better 168 Gbps or higher Backplane capacity and minimum 125 Mpps of forwarding rate "Latency: < 4 µs MTBF: 789 k hours" "Mac Address:32K or more VLAN: 4K or more System Policies: 1.5K or more Max Jumbo Frame: 9216 bytes Multicast Group: up to 1000" "Auto QoS for switch management traffic,Policy-based QoS, Traffic Prioritization, Priority Queues: Eight hardware-based queues per port, SPQ, WRR" Static Routing, MSTP, RSTP, PVST+,IPv6 Tunneling, LACP, LAG, IGMPv3, DHCP, DHCP82,DHCP Relay for IPv4/IPv6,Multiple microcode image support with fallback recovery, ARP,SDN support through Restful API and openflow 1.3.1 Switch should be able to support management via CLI, Web interface, all switches & wireless components and switch should have same operating system. Same access points and switches should have option to be managed by cloud infrastructure without replacing the hardware in future. The same device could be managed by cloud without changing the hardware if required. "Dynamic change of authentication (CoA),MAC-based authentication for non-IEEE 802.1X hosts, MAC address lockdown, Prevention from ARP attacks, Web based Authentication, Autosensing IEEE 802.1X multi-client, multi-VLAN support,RFC 1321 MD5, RFC 2284 PPP EAP,RFC 1826/1827/4303/4305 Encapsulating Payload (ESP) and crypto algorithms, RFC 2104 HMAC Message Authentication, Built-in CPU protection against malicious attacks" "Unified management, control and virtual chassis technology, Virtual Chassis 1+N redundant supervisor manager, Virtual Chassis In-Service Software Upgrade (ISSU),Smart continuous switching technology, IEEE 802.3ad/802.1AX Link Aggregation Control Protocol (LACP) and static LAG groups across modules " "Temperature: 0 to 50Deg Humidity: 5% to 95% (non-condensing)" CE, EN 55022, RoHS, WEEE US UL 60950, CSA22.2 FIPS 140-2/NDcPP EN 60825-1/2 Laser, IEC 62368-1 SFP should be of same make as switch. The vendor should be approved by TTP . The offered product should be TEC certified ,ROHS3 Certified. ZTP (Zero touch Provisioning), NTP, RSPAN, DHCP Server, DHCP Relay,802.3ah, 802.1ag, sflow/NetFlow Switch should be manageable through both IPv4 & IPv6.IPV4/ipV6 Dual Stack, ISATAP Tunnel Operating temperature 0-50 Degree C Safety & Compliance FCC Part 15 (CFR 47) Class A, ICES-003 Class A, EN 55032 Class A, EN 55024, CE, CB, EN 55035, IEC 62443-4-1: 2018, UL 60950-1, RoHS3, CISPR-32, EN/IEC:61000-4-29, EN/IEC:61000-4-11, TEC by MTCTE , OEM/product must be approved by TTP ( trusted Telecom Portal).The OEM must have ISO 9001:2015, ISO ISO/IEC 27001:2022,ISO 14001:2015,ISO 45001:2018. The Switch shall work with on-premise and cloud based NMS without change in hardware/software/OS Image.The offered product should be VAPT certified for security of the software . The OEM must have ISO 9001:2015, ISO ISO/IEC 27001:2022, ISO 14001:2015, ISO 45001:2018. The OEM must have TAC centre In country, must have RMA depot in country. The OEM should produce the MAF to authorized partner to participate in the tender. The OEM should provide the escalation matrix if any technical issue. The OEM must have dedicated contact no/ Toll free no furnished with the escalation matrix. The compliance should be provided with the cross reference and the same documents/ datasheets should be available on the OEM s official website. The OEM of the proposed switches should have deployed at least one 500 Nodes campus in PSU /GOVT/Enterprise. Bidder must submit the satisfaction report of the proposed OEM/product from End customer, duly signed and sealed by end customer/designated officer. The bidder must submit the PO (year of 2024/2025) for proposed OEM as bellow: 1 Single PO/supply order for at least 6000 wired Nodes ,1500 wireless access points to a single customer OR 2x PO/supply orders minimum 4000 wired Nodes with min 500 Access points each for 2 customers. PO copies (end customer PO to SI - SI PO To Distributor of OEM) should be submitted by the bidder. Tender committee may ask for the POC (proof of concept ) for the proposed devices /solutions at any point of evaluation process if required . NOS

51 M.R "SITC of 4x4 Access Point Ceiling Mount having 1 x 2.5GE (PoE/PoE+) port , 1 x G Copper port .For 2.4G 4*4 MIMO, For 5G 4*4 MIMO .Built-in omnidirectional internal antennas, Dual frequency with min 6 Stream .For 2.4G: 3dBi and for 5G: 3dBi.200 square meter coverage (without any obstacle).Maximum number of users per band should be minimum 128. power consumption:18W. Encryption: AES, WPA3\802.11i: Supported, Authentication: MAC Address/PSK, Client isolation: Both Layer-2 wireless client isolation and SSID isolation, forwarding security: Packet filter, MAC address filter, and broadcast storm suppression, SSID-VLAN binding: Supported, Management frame protection (802.11w): Supported. Should be CE, FCC, CCC, ROHS certified. Access Points should have option to be managed by cloud infrastructure without replacing the hardware in future required. All Network Switches, Wireless and Fiber Modules must be from same OEM. The detailed Specification as follows Approved Make : Cisco/ Nexxus / Extreme/ Arista/Juniper " Ceiling mount dual band WiFi6 indoor Access Point (AP): (Detailed Minimum Technical Specifications) IEEE 802.11b/g/n/ac/ax 1 x 2.5GE (PoE/PoE+) port, 1 x G Copper port 2.4G 4*4 MIMO 5G 4*4 MIMO Built-in omnidirectional internal antennas, Dual frequency with min 6 Stream For 2.4G: 3dBi and for 5G: 3dBi 5.725GHz to 5.850GHz 2.4GHz to 2.483GHz Should be supported both standalone and With Controller mode Maximum number of users per band should be minimum 128 Local power supply 12V 1.5A DC/Equivalent is supported (optional) Not more than 18W Encryption: AES, WPA3 802.11i: Supported Authentication: MAC Address/PSK Client isolation: Both Layer-2 wireless client isolation and SSID isolation Forwarding security: Packet filter, MAC address filter, and broadcast storm suppression SSID-VLAN binding: Supported Management frame protection (802.11w): Supported Wizard-guided installation with Bluetooth and app. Local management with app / Remote management. Should support cloud environment as well . Remote maintenance. AP locating feature IP 41 Protection .Should have in built template for different scenario, Support 5 G ,Operating temperature 0-50 Degree C , All switches & wireless components and switch should have same operating system .Same access points and switches should have option to be managed by cloud infrastructure without replacing the hardware in future .All teh wireless componennts along with commercial grade & industrial grade switches , Firewall should be from teh same OEM Should be CE, FCC, CCC, ROHS, WPC certified The OEM of the proposed switches should have deployed at least one 500 Nodes data centre in PSU /GOVT/Enterprise. Bidder must submit the satisfaction report of the proposed OEM/product from End customer, duly signed and sealed by end customer/designated officer.Atleast 2 staisfactory report from end customer for campus/data centre/cctv network deployment from end user . POC can be required at any point of evaluation of the bid or any time if required before awarding the tender . NOS

52 M.R "Supply, Installation, Testing & Commissioning of AI/ML Based Wireless controller, should have min 8x10/100/1000 Base T ,Min 1x10GSFP+ Port,2x 100/1000 Base SFP in Combo WAN ports . Should be managed as on premise or Cloud environment. Controller should accommodate 256 Access point. Not more than 50W in full load. QOS: Load balance, IEEE 802.11e, Domain based flow control. management,802.11g,802.11i, ISO/IEC. Topology discovery option for cloud management. Authentication: RADIUS, AAA Accounting, Authentication through Portal . Should be loaded with license of all APs in the BOQ. All Network Switches, Wireless and Fiber Modules must be from same OEM. Approved Make : Cisco/ Nexxus / Extreme/ Arista/Juniper " Wireless controller (Detailed Minimum Technical Specifications) min 8x10/100/1000 Base T ,Min 1x10GSFP+ Port,2x 100/1000 Base SFP in Combo WAN ports .1x USB ports , Should have built in LCD screen to see temperarture , operatinoal time etc . Controller should able to accommodate 2030 Access point 10°C~50°C AC discovery through Option43 and DNS AC&AP cross-layer3 networking and cross-NAT networking Layer-2/Layer-3 roaming AC, AP synchronization of clock, version and configuration Local and cloud portal authentication SMS authentication Account-based period control and bandwidth control Authentication-free whitelist Not more than 50W in full load ACL and firewall policy of IP, MAC Rich VPN protocols such as L2TP/PPTP, IPSEC, GRE and SSL ARP anti-spoofing functions such as ARP Scan, DHCP Snooping Attack protection such as Anti-Flood, Ping of Death, Teardrop, WIPS/WIDS, Static / Dynamic Blocklist, URL Filter, Flow classification based on IP quintuple, queue scheduling functions such as CBWFQ , Blacklist and white list, Elastic bandwidth control policies based on user groups and time period, Should have inbuilt LCD for real-time operation, fault diagnosis and online help information, NTP Server, FTP Server, Multiport Binding, Should support roaming within same controller or amongst redundant controller, IEEE 802.11/a/b/g/n/ac/ax support . Load balance, IEEE 802.11e, Domain based flow control Automatic channel negotiation, Static Channel configuration, Automatic power transmission mechanism, Channel should be configured when AP is in operational mode for hassle free deployment environment. RADIUS, AAA Accounting, Authentication through Portal Console Telnet, SSH, SNMP, TR069 management,802.11g,802.11i, ISO/IEC Topology discovery option for cloud management SET

53 M.R "Supply of 1 Gigabit optical transceiver SFP). Supports monomode fiber over 1310nm wavelength nominal) with an LC connector. Approved Make: Cisco/ Nexxus / Juniper/ Arista " All the Switches, APs, NMS, Wireless Controller, SFP Modules must be from the One OEM. Core to Access connectivity should be on 10G and Access to Access Switch should be stacked together at all the locations. OEM Criteria for Passive Networking items. OEM must provide declaration on conformity of all the passive components to the following standards: a) TIA/EIA 568-2.D ; b) TIA/EIA 568-3.D ; c) ISO/IEC 11801 OEM must be a member in the TIA and BICSI organization. OEM shall have RCDD certified manpower in India for design support and validation. Certificate is Mandatory OEM should have valid ISO 9001 and ISO 14001 certificate on Design, development and manufacture of SW and HW solutions for communication networks. All the products must have RoHS Compliance and from One OEM NOS

54 M.R 12 Port LIU Switch : Supply of 12 Port Loaded LIU with SC Unit for 12 SM fiber Single Mode fibres OS2 (2 Nos. of Loaded Duplex adapter with Adapter plate) along with 1 Pc of Splice Tray -12 Fiber Capacity &12 Nos. of SC Pigtail - Pigtail 1 Meter SM Os2 (Make:Molex/Panduit/Siemon) Detailed Specs for Fiber Optic LIU Rack Mount LIU (6 Ports) Fiber optic patch panel : Fiber optic patch panel FMS Termination Drawer should have sufficient slots to accommodate 3 of 12/16 Port LC Adaptor Plates. Should have Slide type drawer structure Height: 1 U, 1.75 inches (12 & 24 Ports) Material: Cold Rolled Steel in surface coated by electrostatic epoxy powder Slots: FMS should have sufficient slots to accommodate adaptor plates Empty Slots of FMS should be covered with blank plates. Splice Tray : Splice Tray of ABS, Comply with UL 94V2 material should be supplied with LIU. Detailed Specs for 6/12/16 Port LC/SC Type Adaptor Plates (SM OS2) The adaptor plate should be pre-loaded with LC/SC Type Single ModeDuplex Adaptors. Port Density :6/12/16 LC/SC Single mode Ports All LC adapters should be duplex type with shutter for protection. Adapters should be snap mount for easy insertion and removal. Insertion Loss: <0.2 to <0.1 dB Compliance :RoHS Compliant Detailed Specs for LC Type 9/125μm SM Fiber Optic Simplex Pigtail Type : 9/125 micron fibre performance Jacket Material : LSZH complying to IEC 61034-1 & 2,IEC-60332-1, IEC-60754-1 & 2 Operating Temperature: -40°C to +75°C Connector Insertion Loss: 0.30dB(Max) Attenuation: 1310/1550 : 0.36/0.22 dB/KM NOS

55 M.R Supply of Fiber Duplex Patch Cords SC-LC/LC-LC SM Patch Cord 2 mtr. (Make:Molex/Panduit/Siemon) Detailed Specs for Patch Cord, LC SC, Duplex, MM OM3, Bend Insensitive G651, PC, LSZH Cable : LC/SC-SC/LC 9/125μm or 1310 μm SM Duplex Patch Cord Length : 2mtrs (as per requirement) Connectors : The optical fiber patch leads shall comprise of Single Mode 9/125μm or 1310 μm fiber with 2XLC type fiber connectors terminated at one end of fiber patch cord and 2xSC type connector at other end of the fiber patch cord Insertion loss should be better than ≤ 0.30 dB Jacket Material : LSZH complying to IEC 61034-1 & 2,IEC-60332-1, IEC-60754-1 & 2 Attenuation: 50/1300 : 3.0/1.0 dB/KM Connector Loss : 0.30dB(max) Operating Temperature : -40°C to +75°C NOS

56 M.R Supply of 6 core Single mode OS2 Loose tube Armoured Optical fiber cable through existing conduit: The Fiber should be OS2 Single Mode Optical Fiber Cable of Size 9/125µm. (Make:Molex/Panduit/Siemon) Detailed Specs for Outdoor F/O Cable, Loose Tube, SM – 1x6 Fibers, Central Steel rod with CST, PE The fiber should be optimized for operation at 1310 nm and at 1550 nm. Should fulfill the requirements of ISO.IEC 11801 - 2nd Edition, type OS2, ITU-T REC G 652D spec IEC 60794-1-2 F5 Fibre Count : 6 /12 Fiber count per tube :6 / 12 Filler count :4 Filler Material : PP Max. Attenuation: At 1310 nm <= 0.36 dB/km, At 1550 nm <=0.22 dB/km Fibre/Tube Identification : Multi Tube Fibre protection (Tubes) : Polybutylene Terephthalate (PBT) Armouring : CST Thickness : 1.6mm Outer Sheath :UV Stabilised Polyethylene (PE) Central Strength Member: Steel wire coated with PE Water Blocking : Thixotropic Gel (Tube); Petroleum Jelly (Interstices) Cable Diameter (D) : 9.0 ± 0.5 mm Mass (Nominal) : 91 kg/km Min. Bending Radius (during Installation) : 20 D;D-Outer Diameter Max. Tensile Strength-Short Term : 1500N Max. Crush Resistance-Short Term : 2200N/100 mm Operating Temperature range : -40°C to +70°C Approved Make : PANDUIT / RIT / SIEMON All the cable and accessories are from the same OEM METRE

57 M.R Supply of Fully Loaded 24 port UTP jack panel (24 port RJ-45 Loaded CAT-6 UTP 19" rackmountable patch panel preferbaly with 6 blocks). (Make:Molex/Panduit/Siemon) Detailed Specs for 19" 1U 24 port unsheilded Patch Panel Patch panel should be modular design, populates up to 24 UTP keystone-type jacks in 1U Patch panel should be Enhanced with cable strain relief with retention tray; It should be single metal both front panel and rear tray Material: sub-rack made of MS Steel with dimension 44.4 mm : 482.6 mm : 105 mm (h:w:d) tray Information Outlet or connectin module should comply with the specification mentioned above in 2 Standard : Conforms to IEC-60603-7 (603-7) for keystone-type, snap-on apertures Should be RoHS complied NOS

58 M.R Supply of Straight LAN Patch Chord-1 Mtr (Make:Molex/Panduit/Siemon) Detailed Specs for Patch Cord, U/UTP 4P, Cat.6, length 1/2 Metre Standardization: Compliant with Cat.6, Class E requirements: ISO/IEC 11801 2nd Edition Compliant with Cat.6 component standards IEC 60603-7-4 and 60603-7-5 Cable shield: U/UTP Number of conductors : 8 Stranding: 7 x 0.20 mm (24 AWG) Cable jacket characteristics: cable, metal-free Cable overall diameter: 6.5±0.2 mm Tube / Wire type: stranded conductor Insulation: solid polyolefin, 0.97±0.02 mm diameter Plug: Feature cable retension, with enhanced pull strength. Cat 6 patch cord plug to have round cable holder and strain relief boot to avoid bending. Jacket: PVC with 8 different color options Plug should have high repeatability cross talk performance NOS

59 M.R Splicing of Armoured SM/MM Fibre Optics Cable: Splicing, testing and commissioning of supplied, OFC cable of 6-Core Armoured Fibre Optics core

60 M.R Supply of Fully Loaded 15U 19" 600*600 Wall Mounted Rack with all required accessories -2 Nos. of Fan,16A 6 Plug PDU-1 Nos. ,Cable Manager-2 Nos., Mounting Screws-20 Pcs ; The Front frame should be integrated with top, bottom, front and two side panels for better rigidity and strength, Front Glass Door with Lock loaded, Compliance with standards shall be UL 2416., DIN 41494, IEC EN 60529, IEC EN 62262 , IEC EN 60068-2-11 , ISO 9001:2008i Preffered Make-Legrand/Netrack/President/Valrack NOS

61 M.R Supply, delivery, installation & testing of Modular G.I. box 18 SWG Sheet ISI marked with Modular base & cover for 2 moudle RJ45 socket outlet..(Make- Molex/Panduit/Siemon) NOS

62 M.R Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess includingcutting the wall and making good the same in case of recessed conduit as required. Preferred Make- AKG/NORPACK/Polycab/Dauphin

62.1 20 mm METRE

62.2 25 mm METRE

63 M.R Supply of UTP 4 PAIR Cat 6 LAN 1 run cable Wire for Data : The 4 pair Unshielded Twisted Pair cable shall be UL Listed,exceeds the requirements of ANSI/TIA-568-C.2 and ISO/IEC 11801 Class E , 4 twisted pairs separated by internal PE Cross Separator. Full separator. Half shall not be accepted. Rip Cord is must,Insertion Loss of 32.8 db/100m at 250 MHz ,Cable should support operating temperature from -20° to +70°C Cable support Conductor Resistance ≤ 9.38 Ω/100m Max., Cable support Delay Skew: < 45 ns/100m, Operating Voltage: 72V , Impedance: 100 ± 15 Ω @100 MHz. and Propagation Delay @250 MHz : 536 ns/100m, ETL Verified 4 connector channel performance up to 700 MHz , RoHS Compliant. 1 Run CAT6 UTP Cable (for Network only . (Make:Molex/Panduit/Siemon) METRE

64 M.R Supply , installation , testing and commissioning of Enterprise Grade IP Based Unified Communication System with IP at Core Architecture supporting minimum 80 IP Phones and 64 Simultaneous Calls, scalable up to 2000-2100 VoIP/SIP Users, minimum 99 SIP Trunks, 248 VoIP/Vocoder Channels, 64 Voice Mail Channels, 64 Party Conferencing, Call Recording, IVR, Auto Attendant, Desktop/Mobile Soft Client, IPv4/IPv6, SRTP/TLS Security, QoS, Gigabit LAN/WAN Ports, USB Storage and Web Based GUI Management. System shall support minimum 550 RTP Calls and 124 Transcoding Calls, and be supplied in 19” Rack Mountable 1U Appliance with built-in support for 1+1 Active-Active Redundancy, expandable in future without replacement of existing system. Operating Temperature 0°C to +45°C (32°F to113°F) , Operating Humidity 5-95% RH, Non-Condensing SET

65 M.R Supply , installation , testing and commissioning of VoIP-FXO Gateway (8 VoIP & 8 FXO Ports) SIP protocol (9 SIP accounts); 8 VoIP channels; 8 FXO ports; 0 FXS port; 2 Ethernet ports; 12V DC adaptor-based power supply; Approved Make- Matrix/Alcatel/Tadiran NOS

66 M.R Supply , installation , testing and commissioning of SIP IP Phone (Basic): 128x64 pixel graphical LCD (3.1 inch or higher) with LED indicators for incoming/ongoing call, mute and hold; multi-language UI with caller ID (name & number); interface with 2 x RJ45 Ethernet ports (10/100/1000 Mbps), IEEE 802.3af support, 1 x RJ9 handset port and DC power jack; audio codecs G.722, G.711 (A/μ), G.729, G.723 with DTMF support (in-band, RFC 2833, SIP INFO); full duplex speakerphone with VAD, CNG, AEC, AJB and AGC; physical keys include 3 feature keys (headset, mute, hands-free), 4 context sensitive keys, 2 line keys, navigation/call appearance/feature status keys and volume control keys; supports wall mount and table-top installation, black color; operating temperature 0°C to 45°C, humidity 5% to 95% RH non-condensing; features include call logs, mute, redial, hotline, auto call back, auto answer and call transfer; call management supports message waiting lamp, voice mail, group and selective call pickup, paging; certifications CE, FCC, EMI/EMC, Safety and RoHS compliant. Offered product shall be TEC MTCTE Certified against applicable Essential Requirements (ER) and comply with Indian Telegraph (Amendment) Rules 2017, DPIIT PPP Order 2017 (Revised July 2024) and applicable DoT PPP-MII / TEC GR-IR Requirements with valid Minimum Local Content Declaration from OEM. All active components including IP-PBX, SIP Phones and shall be from the Same OEM with valid MAF, warranty and back-to-back OEM support.Approved Make- Matrix/Alcatel/Tadiran NOS

67 M.R Supply of HDMI ‐ HDMI Cable 10 Mtrs, Preferred Makes-Crestron/Extron/Lightware NOS

68 M.R Supply of STQC certified 5MP IR Bullet Camera (2.8 mm Lens) with Audio Support •1/2.8” SONY - CMOS •5MP, Color - 0.01 Lux @F1.2 (AGC ON), Monochrome - 0 Lux •Horizontal Field of View: 88 to 32 degrees and IR Range of up to 50 meters, Focal Length-2.8 mm •Video Analytics: Object Counting, Trip Wire, Intrusion Detection and Motion Detection •H.265/H.264/M-JPEG Video Compression •PoE Support, NAS Storage, SD Card(512GB), Quad Stream Support, 1/1 Audio I/O, 1/1 Alarm I/O •True WDR, 3D Noise Reduction, Adaptive Streaming, Smart Streaming and ROI, SNR > 70 dB •BIS, CE, FCC, RoHS, IK10, IP67, UL, NEMA 4X Preferred Make- Bosch/Pelco/Matrix NOS

69 M.R "Supply of STQC certified 5MP IR Dome Camera (2.8 mm Lens) with Audio Support •1/2.8” SONY - CMOS •5MP, Color - 0.01 Lux @F1.2 (AGC ON), Monochrome - 0 Lux•Horizontal Field of View: 107.6 degrees and IR Range of up to 50 meters, Focal Length-2.8 mm •Video Analytics: Object Counting, Trip Wire, Intrusion Detection and Motion Detection •H.265/H.264/M-JPEG Video Compression •PoE Support, NAS Storage, SD Card(512GB), Quad Stream Support, 1/1 Audio I/O, 1/1 Alarm I/O •True WDR, 3D Noise Reduction, Adaptive Streaming, Smart Streaming and ROI, SNR > 70 dB •BIS, CE, FCC, RoHS, IK10, IP67, UL, NEMA 4X Preferred Make- Bosch/Pelco/Matrix " the camera shall support video analytics including motion, tamper, intrusion, line crossing, loitering, object counting, abandoned/missing object, and audio exception, along with privacy masking and event-based recording; the camera shall support two-way audio, alarm I/O, edge storage up to 512GB with NAS/SFTP, ONVIF S/G/T compliance, and protocols including TCP/IP, HTTP, HTTPS, RTSP, FTP, SMTP, SNMP, TLS, and 802.1x; the camera shall include cybersecurity features such as secure boot, signed firmware, AES-256/RSA-2048 encryption, HTTPS (TLS 1.2), and IP filtering, and shall operate on 24V DC/PoE with max 25W consumption, suitable for -30°C to +60°C with IP67, IK10, NEMA 4X protection and BIS, CE, FCC, NDAA, and STQC compliance.Preferred Make- Bosch/Pelco/Matrix NOS

70 M.R Supply of 32 Channel NVR with 4K Support and 8 HDD SlotsHW PROF 69,000.00 NA• 32 IP Channel Inputs; 4K HDMI, 1/1 Audio I/O and 2/1 Alarm I/O• 12MP, 8MP, 5MP, 4MP, 3MP, 2MP, 720p, D1 and CIF Recording Resolution• 4x 4K/ 10x 3MP/16x 1080p Local Decoding • 4 SATA HDD Support (Maximum 10TB Capacity per Slot, Hard Disk Not Included) • Save Storage Space with Adaptive Recording and Camera-wise Recording Retention• SMS & Email Notification, Video Pop-up, Alarms and Instant Calling from Mobile Application• Throughput - 512Mbps Uplink, 180Mbps Downlink, ONVIF profile S (G &T upcoming) and SDK • Cascading: Server-less centralized control & mobile live view of multiple NVR clusters via software • ANR : Automatic Network Replenishment (upcoming) ,NDAA Compliant Product, MTBF>100,000 hour,Preferred Make- Bosch/Pelco/Matrix NOS

71 M.R Supplying of 10 TB Enterprise / Surveillance Class internal Hard Disk Drive (HDD) with SATA-III (6.0 Gb/s) interface, spindle speed of 7200 RPM, and high-speed cache memory (256 MB or higher). The drive shall be engineered specifically for 24x7 heavy duty multi-channel continuous write-intensive video recording workloads with high MTBF (Mean Time Between Failures) rating of minimum 1.0 to 2.0 million hours, rotational vibration (RV) sensors for multi-bay rack environments, suitable for meeting minimum 30 days video recording backup retention, compatible with NVR/Storage servers, complete with mounting hardware and screws. NOS

72 M.R Supplying of 256 GB MicroSDXC / SD Memory Card, Class 10, UHS-I (U3 / V30) rating with continuous sequential read speeds up to 100 MB/s and write speeds up to 40 MB/s or higher. The card shall be high-endurance / surveillance grade designed for continuous edge-recording (ANR - Automatic Network Replenishment) in IP cameras, with operational temperature resistance (-25°C to 85°C), waterproof, shockproof, and X-ray proof build, complete with SD adapter where required. NOS

73 M.R Supply of Operator Client workstation: U7-13900/16GB/ 1TB SSD/Win 11 Pro/No Monitor/DVDRW/3 yrs / NVIDIAGeForce RTX™ 3070, 8 GB GDDR6, 3 DP; Preferred Make-Dell/HP/Lenovo NOS

74 M.R Supply, Installation, Testing and Commissioning of 55" LED Display Panel, with 4K Resolution : 3840 x 2160, 500 nits (cd/m2) Brightness, contrast ratio : 4000:1, response time : 8ms, Display Colors- 16.7 Mill; Built in Speaker-10W+10W ; Inputs : HDMI x 2, DVI‐D, DisplayPort, Audio, RS‐232 Control, 24x7 Operation.; Preferred Make LG/Samsung/Panasonic NOS

75 M.R SITC of 5kVA/5 kW 1-Phase Input / 1-Phase Output Online UPS System with follwing detailed specifications ; Preffered Make- Delta/ BPE/Vertiv "a) True Online configuration with double conversion UPS b) DSP based technology with reduction in electronic components. c) Fully rated power (kVA=kW) for maximum power availability. d) Possibility of enhancing UPS capacity / redundancy by operating UPS in N+X Parallel Redundant Configuration(PRS). e) UPS should be designed at Rated PF of 1 i.e. 5kVA /5kW UPS rating. f) UPS shold have IGBT topology for both PFC (power factor correction) and inverter. g) Output terminal for critcal & non critcal loads. h) Fan failure/life prediction & Speed control. i) Battery Aging Detection " 1-Phase / 2-Wire & Gnd (Phase & Neutral + Ground) "100 - 280V AC 100 ~ 175V with linear de-rating 50 ~ 100%" 50 / 60 Hz (Auto selectable) 40 to 70 Hz > 0.99 on Full Load < 3% on full load Compatibility to genset supply required Should be provided at the input of the UPS suitable for the full rated capacity of the UPS 200/ 208/ 220/ 230/ 240VAC (Selectable) ±1%(linear load) 50 / 60 Hz +/- 0.05 Hz < 1 Hz / s Pure sine wave < 2% (For Linear load) 3 : 1 On Full Load (Minimum) Electronic / Fused "Nil from Mains mode to Battery Mode Nil from Battery Mode to Mains mode" < 4 ms Should be provided to take care of uninterrupted transfer of load from Inverter to bypass (under overload / fault conditions) & automatic retransfer from bypass to inverter (on removal of overload / fault conditions) "> upto 95.5% (On Full R Load) " > upto 99 % (On Full R Load) "≤ 105%: continuous; 106 ~ 125%, 5 min.; 126 ~ 150%, 1 min.; > 150%: 500ms" "Input: Voltage / Frequency,Bypass: Voltage / Frequency,Output: Voltage / frequency/current, Load level & percentage, Battery Voltage, Capacity, Charge Mode, Last battery test time. " Fault codes are available AC indicator/Battery Mode of Operation / Bypass feeding the load / UPS Fault Battery Low beep / DC Fault beep/ UPS Overload beep/ o/p short ckt fault beep/ Shutdown beep 60 minutes on each UPS 240 V DC Sealed Maintenance Free (SMF) - 12V Cells Amara Raja / Exide / HBL / Amco / Rocket The charger should be able to deliver charging current equivilanet to 10% of Battery Ah rating offered.(In case of external chergers, suitable monitoring of the chargers should be provided in the UPS. Also all external chargers taking AC input must have PFC - Power factor correction) "3 stage superior charging with intermission stage Float Voltage: 13.7 per battery minimum Boost Voltage: 14.0 per battery minimum" 8-10 hours Should be compact and space saving MS steel open racks complete with interconnectors 1.75 VPC Available Available Available "Provide both onsite & remote EPO to shutdown UPS when emergency situation happens. REPO Port with a user-supplied switch" Monitors and controls the status of the UPS via a network system. (OPTIONAL) "UPS should start up On AC Supply (Mains) without DC Supply (Batteries) On DC Supply (Batteries) without AC Supply (Mains)" UPS should start up automatically on mains resumption after battery low shutdown UPS should be capable to carry out self test of Rectifier / Charger /Battery & Inverter module during start-up 0 to 40 deg C -15 to 55 deg C 5% ～ 95%RH (No Condensing) 1000 m.a.s.l (meters above sea level) Forced Air < 48 dbA at I meter distance Rack & Tower mountable UPS should have internal anticorrosion air filters for dust filtration (optional) "QMS: As per ISO 9001: 2008 EMS: As per ISO 14001: 2004 OSHAS: As per ISO 18001: 2007" "EN 50091-2:1995,Class A ESD:IEC61000-4-2: level4 RS : IEC61000-4-3: level3 EFT: IEC61000-4-4:level4 SURGE: IEC61000-4-5:level4 CS: IEC61000-4-6: level3 Conducted Magnetic Field:IEC61000-4-8: level3 " UPS should be ROHS & CE complied Available Manufacturer - QMS: As per ISO 9001: 2015 ISO 45001 :2018 EMS: As per ISO 14001: 2015 OSHAS: As per ISO 18001: 2007 Quality Management System - TL 9000 NABL Factory calibration lab of OEM in INDIA 2 U Size NOS

76 M.R Supply, Installation, Testing and Commissioning of Corded Digital Deligates Units Gooseneck microphone with programmable switch . With Specifications such as: Frequency response:200 Hz to 12.5 kHz. -Headphones load impedance:> 32 ohms < 1k ohm, -Loudspeaker nominal output:72 dB SPL, - Length of microphone :480 mm (18.9 in), - Plug and play functionality for ensuring fast installation and reconfiguration times , Immunity to mobile phone interference and with Features such as: Possible-to-speak indication, Request‑to‑speak indication, Built-in loudspeaker with volume control, Built‑in 3.5 mm (0.14 in) stereo headphones socket, Built‑in volume control for headphones, Color-coded LED indicator above microphone button, for showing the following states: microphone on, request‑to‑speak, and possible‑to‑speak, Immunity to mobile phone interference Make & Model is: Bosch- CCSD-DL./Harman/Televic EACH

77 M.R Supply, Installation, Testing and Commissioning ofCorded Digital Chairman Unit Gooseneck microphone with programmable switch With Specifications such as: Frequency response:200 Hz to 12.5 kHz. -Headphones load impedance:> 32 ohms < 1k ohm, -Loudspeaker nominal output:72 dB SPL, - Length of microphone :480 mm (18.9 in), - Plug and play functionality for ensuring fast installation and reconfiguration times Immunity to mobile phone interference and with Features such as: Possible-to-speak indication, Request‑to‑speak indication, Built-in loudspeaker with volume control, Built‑in 3.5 mm (0.14 in) stereo headphones socket, Built‑in volume control for headphones, Color-coded LED indicator above microphone button, for showing the following states: microphone on, request‑to‑speak, and possible‑to‑speak, Chaiman Button;Preferred Makel is :Bosch- CCSD-DL./ Harman/Televic EACH

78 M.R SITC of Digital central conference controller with Built‑in MP3 recorder with internal memory and USB recording, Built‑in Digital Acoustic Feedback Suppression, Quick and easy connection upto 80 discussion devices, Native support for automatic HD camera control, Signal to noice :> 94 dBA, Frequency response for input :30 Hz to 20 kHz, Recording/ Playback (bit rate):64, 96, 128, 256 Kbit/sec, Nominal loudspeaker output:72 dB SPL and Functions such as: Plug-and-play functionality, Web browser control, Open microphone control, Built-in MP3 recorder, Discussion control Make & Model is: Bosch-CCSD-CURD/ Harman/Televic EACH

79 M.R Supply, Installation, Testing and Commissioning of Networkable Digital Signal Processor having min 6 AEC Inputs and 04 Outputs with IP/RS-232 Control ort; having integrated digital bus/network for expansion of inputs and output ports. The processor shall have programmable DSP like compressor, limiters, EQ, duckers, feedback control, Sampling Rate 48kHz or better,A/D-D/A Converters- 32-bit or better, Phantom Power +48VDC , etc. complete with standard accessories complete as required with following Compliance CE, FCC Part 15B, Industry Canada ICES-003:7, Intertek ETL (US, CA), RoHS, REACH. Preferred Make- Creston / Xillica / Harman/EV NOS

80 M.R Supply, Installation, Testing and Commissioning 8" Two-way Powered Speaker with one 1.25" or bigger HF compression driver with a Frequency Response(-3dB):- 58Hz-19 KHz & In built Power amplifier of 1000 W or better. The Loudspeaker should have a Max. SPL of >125dB.The Sound Dispersion should be 90° x 60° or higher. The speaker should have built in Digital Mixer with Automatic Feedback suppression. It should have at least two XLR/TRS inputs and should have built in Phantom Power.It should have polypropylene enclosure. It should have high quality Bluetooth stereo streaming facility & also bluetooth control & monitoring using OEM Application through a mobile or tablet.(Approved Makes: Bose, Nexo, Electro-Voice) NOS

81 M.R Supply, Installation, Testing and Commissioning of Headworn Wireless Mic with Cardiod polar pattern for transmitter,Dynamic microphone with Neodymium magnet , Receiver frequency response 80Hz-18kHz,Receiver RF sensitivity < 1.0 µV,Receiver Image rejection>55dB,Receiver Dyanmic range >95dB and receiver having 32 channels possible,Receiver S/N ratio >100dB A,distortion <1 %, Transmitter sensitivity - 3.2 mV/Pa,modulation:+/-40kHz (Approved Makes: Audio Technica, Senheiser, Electro-Voice) NOS

82 M.R Supply, Installation, Testing and Commissioning of Modular Cable cubby with fully Retracting Lid, aluminium black anodized cover, Consisting of 1 x HDMI retractable cable which retracts gracefully by simply lifting it vertically above the table, , 1 x LAN and 1 x 5 Amp Power Socket, Make - Magnum/Crestron/Karmer NOS

83 M.R Supply, Installation, Testing and Commissioning of Interactive Flat Panel: Size-86" , Brightness :350; Panel Type: VA; Resolution :3,840 x 2,160;Pixel Pitch (HxV), 0.4875(H) mm x 0.4875(W) mm; Contrast Ratio: 4000:1(without glass); Response Time: 6ms(Typ.); Colour Gamut : 72%; Glass Haze: 2%(without glass); Operation Time Support : 16/7 ; HDMI In: 2; DP In: 1 ; USB: 2(Main/Tray), 2.0/3.0, External(Tray); Audio Out: Stereo Mini Jack; Video Out: Yes; RS232 In : Yes; RJ45 In: Yes; WiFi: Yes; Bluetooth: Yes.complete as required. Make-Samsung/LG/Vivitek NOS

84 M.R Supply, Installation, Testing and Commissioning of Interactive Flat Panel: Size-75" , Brightness :350; Panel Type: VA; Resolution :3,840 x 2,160; Contrast Ratio: 4000:1(without glass); Response Time: 6ms(Typ.); Colour Gamut : 72%; Glass Haze: 2%(without glass); Operation Time Support : 16/7 ; HDMI In: 2; DP In: 1 ; USB: 2(Main/Tray), 2.0/3.0, External(Tray); Audio Out: Stereo Mini Jack; Video Out: Yes; RS232 In : Yes; RJ45 In: Yes; WiFi: Yes; Bluetooth: Yes.complete as required. Make-Samsung/LG/Vivitek NOS

85 M.R Supply, Installation, Testing and Commissioning of Interactive Flat Panel: Size-65" , Brightness :350; Panel Type: VA; Resolution :3,840 x 2,160; Contrast Ratio: 4000:1(without glass); Response Time: 6ms(Typ.); Colour Gamut : 72%; Glass Haze: 2%(without glass); Operation Time Support : 16/7 ; HDMI In: 2; DP In: 1 ; USB: 2(Main/Tray), 2.0/3.0, External(Tray); Audio Out: Stereo Mini Jack; Video Out: Yes; RS232 In : Yes; RJ45 In: Yes; WiFi: Yes; Bluetooth: Yes.complete as required. Make-Samsung/LG/Vivitek NOS

86 M.R Supply, Installation, Testing and Commissioning of OPS Device for intractive Panel with 8th Gen Intel Core i5 8th Gen, 8260u 4K@ 60Hz processor, 16GB DDR4 RAM, 128GB SSD, 1TB HDD, WIFI+BT, Win 11, Wireless Keyboard & Mouse; Make-: As compatiible to the Intractive Panel NOS

87 M.R Supply, Installation, Testing and Commissioning of 4K60 4:4:4 transmitter to interoperate with a receiver for the transmission of a HDMI® signal. It should be used with a CAT5e or higher twisted pair cable to extend the HDMI Signals. For 1080p, WUXGA, and 2K signals, a cable length of up to 230 ft (70 m)should be supported. For UHD and 4K signals, a cable length of up to 130 ft (40 m) should be supported. It should support HDR10, HDR10+, and Dolby Vision® video formats, shold have compliance with HDCP 2.3,CEC (Consumer Electronics Control) , pass-through capability,EDID pass-through capability, Compact surface-mountable designMake-Prefferred Make-Crestron/Lightware/Key-Digital/Kramer NOS

88 M.R Supply, Installation, Testing and Commissioning of 4K60 4:4:4 Receiver to interoperate with a Traansmitter for the reception of a HDMI® signal. It should be used with a CAT5e or higher twisted pair cable to extend the HDMI Signals. For 1080p, WUXGA, and 2K signals, a cable length of up to 230 ft (70 m)should be supported. For UHD and 4K signals, a cable length of up to 130 ft (40 m) should be supported. It should support HDR10, HDR10+, and Dolby Vision® video formats, shold have compliance with HDCP 2.3,CEC (Consumer Electronics Control) , pass-through capability,EDID pass-through capability, Compact surface-mountable designMake-Prefferred Make-Crestron/Lightware/Key-Digital/Kramer NOS

89 M.R Supply, Installation, Testing and Commissioning of rack-mountable 4K60 4:4:4 presentation system 04 HDMI® inputs, two pairs of mirrored HDMI and DM Lite outputs with 4K60 scalers, and analog audio inputs and outputs.Should include support of HDR (High Dynamic Range) and Dolby Vision video formats, audio mixing, advanced EDID management, XiO Cloud connectivity, and enterprise-grade security.Ethernet for connectivity to network,USB for Programming;Preffred Make-Crestron/Lightware/Extron NOS

90 M.R Supply, Installation, Testing and Commissioning of 65" LED Display Panel, with 4K Resolution : 3840 x 2160, 500 nits (cd/m2) Brightness, contrast ratio : 4000:1, Supply, 24x7 Operation.; Orientation-Landscape/Portrait,Active Display Area-,428.48 (H) x 803.5 2(V),I/P-DP 1.2- 1 Nos,HDMI 2.0-3 nos,USB2.0-2 Nos,Audio-Stereo mini jack output,Wi-fi/BT Support-Yes,External COntrol- RS232C-Yes, RJ45-Yes,Speaker-10W -2Channel,Operating System-Tizen/WebOS/Android,Safety-60950-1/62368-1,ENERGY STAR 8.0, EPEAT,IP5x,Security-802.1 x (WPA2 Enterprise):EAP-TLS, EAP-TTLS, EAP-PEAP NOS

91 M.R Supply, Installation, Testing and Commissioning of 55" LED Display Panel, with 4K Resolution : 3840 x 2160, 500 nits (cd/m2) Brightness, contrast ratio : 4000:1, Supply, 24x7 Operation.; Orientation-Landscape/Portrait,Active Display Area-,428.48 (H) x 803.5 2(V),I/P-DP 1.2- 1 Nos,HDMI 2.0-3 nos,USB2.0-2 Nos,Audio-Stereo mini jack output,Wi-fi/BT Support-Yes,External COntrol- RS232C-Yes, RJ45-Yes,Speaker-10W -2Channel,Operating System-Tizen/WebOS/Android,Safety-60950-1/62368-1,ENERGY STAR 8.0, EPEAT,IP5x,Security-802.1 x (WPA2 Enterprise):EAP-TLS, EAP-TTLS, EAP-PEAP NOS

92 M.R Supply, Installation, Testing and Commissioning of 1:4 HDMI Distribution Amplifier w/4K60 4:4:4 & HDR Support: designed to split a single HDMI® signal to feed up to eight separate displays, switchers, and/or other devices. It provides full support for UHD and DCI 4K60 4:4:4 and HDR video, HDCP 1.4 or 2.2 copy protection, and high-bitrate 7.1 audio, to ensure optimal performance and compatibility for any HD or 4K video application NOS

93 M.R Supply, Installation, Testing & Commissioning of Full HD PTZ Camera supporting 1080p at 60 Frames per Second, minimum 12X Optical Zoom with FoV of minimum 70 degree and minimum 255 presets. Camera should support simultaneous outputs through HDMI, USB 3.0 & IP with Audio In and controllable via RS232/422 and IP. Panning angle -170° ~ +170° , Tilting angle -30° ~ +90. Camera should support SRT, PoE & should be compatible with Virtual USB Driver. Quoted model should be BIS, Clickshare, CE, FCC & RoHS Certified with Test Lab Reports. Approved Makes Lumens/Panasonic/Sony/ Vaddio NOS

94 M.R ​Supply, Installation, Testing & Commissioning of heavy-duty Ceiling / Wall Mount Bracket suitable for PTZ Camera, fabricated from high-grade steel/die-cast aluminium with anti-corrosion powder-coated finish. The mount shall feature internal cable management / concealed conduit passage, safety tether wire, vibration-dampening design, and universal camera mounting plate compatible with standard 1/4"-20 / 3/8" tripod threads. Complete with heavy-duty anchor fasteners, hardware accessories, and fixing in position as per site requirement and technical direction of Engineer-in-Charge. Approved Make: Standard / OEM (Lumens / Panasonic / Sony / Vaddio or equivalent approved). NOS

95 M.R Supply, Installation, Testing and Commissioning ofFully Loaded 6U 19" 600*600 Wall Mounted AV Rack with all required accessories -2 Nos. of Fan,16A 6 Plug PDU-1 Nos. ,Cable Manager-2 Nos., Mounting Screws-20 Pcs ; The Front frame should be integrated with top, bottom, front and two side panels for better rigidity and strength, Front Glass Door with Lock loaded, Compliance with standards shall be UL 2416., DIN 41494, IEC EN 60529, IEC EN 62262 , IEC EN 60068-2-11 , ISO 9001:2008 Preferred Make-Legrand /Netrack/ President/Valrack NOS

96 M.R Supply, Laying and testing of Mic Cable, CM-Rated, 1-24 AWG stranded high-conductivity bare copper pair with PVC insulation, +90% bare copper spiral shield, PVC jacket, Nom. Conductor DCR-22.8 Ohm/1000ft, Nom. Capacitance Cond-to-Cond-- 33 pF/ft (110 pF/m), Nom. Capacitance Cond-to-Other (Conds + Shield)-61 pF/ft (200 pF/m), Max. Current- 3.9 Amps per Conductor at 25 degree Celcius; Approved make- Krystal/Belden/MX METRE

97 M.R Supply and Laying of HDMI - HDMI Cable 1.8 Mtrs, High- speed Category 2 HDMI® cable,24k gold-plated 19-pin Type A connectors,High-flex CL3-rated jacket, it should have guaranteed end-to-end system performance, should support 4K60 4:4:4 video, 18 Gbps bandwidth @ up to 20 ft (6.1 m), Supports 4K60 4:2:0 and 4K30 4:4:4 video @ 30 ft (9.1 m),RoHS compliant; Preferred etc as required.Preffred Make-Crestron/Extron/Lightware NOS

98 M.R Supply and Laying of HDMI - HDMI Cable 5 Mtrs, High- speed Category 2 HDMI® cable,24k gold-plated 19-pin Type A connectors,High-flex CL3-rated jacket, it should have guaranteed end-to-end system performance, should support 4K60 4:4:4 video, 18 Gbps bandwidth @ up to 20 ft (6.1 m), Supports 4K60 4:2:0 and 4K30 4:4:4 video @ 30 ft (9.1 m),RoHS compliant etc complete as required. Preffred Make-Crestron/Extron/Lightware NOS

99 M.R Supplying and drawing of Shielded Twisted Pair CAT-6 Control cable for Transmitter / Reciever connectivity complete etc. as required in the existing surface/ recessed steel/ PVC conduit as required. Preffered Make- Molex/Crestron/Extron METRE

100 M.R Supplying and fixing of 25 mm medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. Preffered Make- AKG/Dauphin/Polycab METRE

101 M.R Supply, Installation, Testing & Commissioning of Miscellaneous Audio-Visual Cables, Patch Chords, Faceplates & Connectors (Complete System Integration) Lot