PROVISION OF 01X MULTI UTILITY BLOCK AT RMS, PROVISION OF INTERLOCKING PATHWAYS ALONG ROAD SIDE NEAR MAIN GATE AT MH AND PROVISION OF COMPOUND WALL FOR BLDG NO 66 AND 67 LAXMITEK AREA UNDER GE BELGAUM

Amount

Surface excavation n. exc. 30 cm deep and averaging 15cm deep and getting out in hard/ dense soil all as specified and directed.

Excavation in trenches n. exc. 1.5 m wide and n. exc. 1.5 m depth for foundation, etc. and getting out in hard/dense soil all as specified and directed.

Excavation in trenches n. exc. 1.5 m wide and n. exc. 1.5 m depth for foundation, etc. and getting out in any type of soil all as specified and directed.

Excavation in post holes n.exc 0.5 cum in hard/ dense soil, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around in layers n.exc 25 cm watering and removing surplus soil to a distance n.exc 50 m and making good surface all as specified

Returning filling in including spreading levelling, watering and well ramming in layers n. exc. 25 cm thick all as specified and directed.

Removing excavated soil n.exc 50 m and depositing where directed at a level n. exc. 1.5 m above the starting point in soil all as specified and directed.

Removing excavated soil exc. 250m but n.exc 500 m and depositing where directed all as specified and directed.

Rolling and consolidation of formation surfaes in cutting with power roller of capcity exc 8 tonne to 12 tonne all as specified and as directed.

M&L for soling or sub base, 150mm thick spread thickness, with broken boulders or quarried stone, interstices filled, surface formed and rolled and consolidated by using 8 to 10 ton power roller to required gradient and camber all as specified and as directed.

M&L for WBM, 150 mm thick (compacted thickness) in two layers of each 75mm thick, with granite, trap or basalt aggregates of grading 2 (63 to 40mm size) or of grading 3 (50 to 20mm size), spread, rolled and consolidated to gradient and camber required all as specified and directed.

M&L for premix bituminous macadam with 4% binder content (Paving Bitumen), consolidated thickness 75mm or less, laid, rolled and compacted to required gradient and camber all as specified and as directed.

M&L for preparing surfaces of unsurfaced water bound macadam by wire brushes for removing caked mud etc, sweeping with brooms and finally fanning the cleaned surfaces with gunny bags or pneumatic means to remove all loose dirt etc. and applying evenly priming/ tack coat with paving bitumen at 10 kg per 10 sqm all as specified and as directed.

M&L for bituminous pre-mixed semi dense asphaltic concrete 40mm consolidated thickness with 5.5% binder content (Paving bitumen) by weight of total mix, rolled and compacted to required camber and gradient complete all as specified and as directed.

M&L for Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering complete all as specified and as directed.

M&L for hard core with broken stone or boulders of gauge n.exc 63mm, deposited, spread, levelled in layers n.exc 15cm thick, watered and rammed to a true surfaces all as specified and directed.

M&L for plain cement concrete 1:4:8 type D2, using 40mm graded stone aggregate in foundation, filling, mass concrete, levelling courses and sub bases all as specified and directed.

M&L for plain cement concrete 1:3:6 type C1, using 20mm graded stone aggregate in foundation, filling, mass concrete, levelling courses and sub bases all as specified and directed.

M&L plain cement concrete 1:2:4, type B1, using 20mm graded stone aggregate as in coping, bed blocks, eves filling between wall and tile/ sheet roofing including necessary form work all as specified and directed

M&L for plain cement concrete 1:2:4 type B1, using 20mm graded stone aggregate as in surface channels and drains concrete all as specified and directed.

M&L for pre-cast cement concrete solid block masonry, exc 10cm width, blocks cast in PCC 1:3:6 type C1, using 20mm graded stone aggregate, set in CM 1:6 complete all as specified and directed.

M&L for Reinforced cement concrete 1:2:4, type B1, using 20mm graded stone aggregate as in foundation, column footings, plinth beams, etc all as specified and directed.

M&L for Reinforced cement concrete 1:2:4, Type B1 using 20mm graded stone aggregate as in Columns, pillars, piers, posts and struts and the like all as specified and directed.

M&L for Reinforced cement concrete 1:2:4, Type B1 using 20mm graded stone aggregate as in beams, cantilevers, bressummers, lintels over 1.5m span and the like all as specified and directed.

M&L for providing precast cement concrete 1:2:4, type B1, using 20mm graded stone aggregate as in cover slabs, etc. set in CM 1:6 all as specified and directed.

M&L for use of form work to sides of concrete foundations, column footings, plinth beams and similar works for rough finished flat concrete surfaces, vertical or to batter, all as specified and directed.

M&L for use of form work to sides of pillars, posts, struts, columns, etc. for fair finished concrete surfaces, square, rectangular or polygonal all as specified and directed.

M&L for use of form work to sides and soffits of roof beams, tie beams, lintels, and similar works for rough finished flat concrete surfaces all as specified and directed.

M&L for mild steel TMT bars 10mm dia and over cut to length bent to shape required including cranking bending, spirally for hooping for column, hooking ends and binding with and including MS wire (annealed) not less than 0.9mm dia all as specified and directed.

M&L for mild steel TMT bars 6 to 8mm dia and over cut to length bent to shape required including cranking bending, spirally for hooping for column, hooking ends and binding with and including MS wire (annealed) not less than 0.9mm dia all as specified and directed.

All as described in item No. 62 but 6mm to 10mm dia as in stirrups, spacers and binders

M&L for 75mm thick plain cement concrete 1:4:8 type D2 using 40mm graded stone aggregate as in sub base for flooring including finishing the surface even and fair all as specified and directed.

M&L for 25mm thick plain cement concrete 1:2:4 type B0 using 12.5mm graded aggregate as in sub base for floor all as specified and directed.

M&L for machine cut Kota stone slab, 20-25mm thick, as in flooring, set and jointed with neat cement slurry and pointed with grey cement mixed with pigment to match the shade of the slab laid over 20mm thick screed bed in cement mortar 1:4 including rubbing and polishing complete all as specified and as directed.

M&L for machine cut Kota stone slab, 20-25mm thick, as in risers of steps, skirting, dado, cladding to pillars, etc., laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including bull nosing the edges, rubbing and polishing complete including 10mm thick backing coat in CM 1:4 complete all as specified and directed.

M&L for coloured non skid ceramic tiles, edge cut, 7 to 8mm thick area of each tile exc 0.06 Sqm but not exc 0.11 Sqm, in floors, etc. set and jointed in neat cement slurry and pointed in white cement mixed with colouring pigments to match the shade of the tile laid over and including 15mm thick screed bed in cement mortar 1:4 all as specified and directed.

M&L for coloured glazed ceramic tiles 300mm x 450m size, 7 to 8mm thick on vertical surfaces such as skirting, dados etc. set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match with surfaces including 10mm thick backing coat in CM 1:4 all as specified and directed.

M&L for 80mm thick machine pressed precast concrete interlocking coloured paver blocks, M-35 grade, any shape and size with glossy finish on top confirming to IS 15658-2006 all as specified and directed.

M&L for crushed stone sand (M-sand/ Robo sand/ I-sand) as in cushioning for interlocking paver blocks including watering and consolidating complete all as specified and as directed.

M&L for providing and laying factory made kerb stone of M-25 grade cement concrete in required line, level and curvature, jointed with Cm 1:3, including making joints with or without groves including making drainage opening wherever required complete all as specified and as directed.

M&L for rendering 10mm thick in cement mortar 1:4 on fair faces of brick work or PCC block masonry or concrete surfaces finished even and smooth without using extra cement complete all as directed.

M&L for rendering 5mm thick in cement mortar 1: 4 mixed with water proofing compound over 10mm thick backing coat in cement mortar 1:6 on fair faces of brick work or PCC block masonry or concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed. Note: Water proofing compound shall be measured and paid separately.

M&L for rendering 15mm thick in cement mortar 1:4 on fair faces of brick work or PCC block masonry or concrete surfaces finished even and smooth without using extra cement complete all as directed.

Supply only 20mm thick pre-formed filler, cut to required size and provided into expansion joints all as specified and directed.

M&L for powder coated aluminium frame work as in doors, partitions and windows using standard aluminium extruded sections with thickness of powder coating not less than 50 microns including provision of glazing clips, hinges, handles, etc all as specified and as directed. Notes: (i) All the aluminium sections provided under this item shall be measured and converted into weight for payment with the designated unit weight mentioned in the manufacturer's catalogue for the corresponding aluminium sections/ fittings. (ii) The rate quoted deemed to include necessary grouting/ embedding of the aluminium frames/ supports into floors/ walls and making good the disturbed surfaces to match with the existing surfaces and provision of necessary rubber gaskets. (iii) Particle board/ glass panels shall be measured and paid separately.

M&L for aluminium sliding windows (Triple track), fabricated to required size with standard aluminium anodised sections, with bottom track of size 92 x 31.75 x 1.6mm, side and top frame of size 92 x 31.75 x 1.4mm, top and bottom shutter rail of size 39x17x1.4mm, outer style of size 39 x 17 x 1.4mm, interlock style of size 39 x 27 x 1.4mm, including provision of 4mm sheet glass ordinary quality for panels including provision of all hardware fittings such as handles, locking arrangements, rubber gaskets, rollers, spring catchers etc. complete all as specified and directed.

M & L for 5.5mm thick sheet glass ordinary quality and glazing with oil putty/ neoprene beading in square n. exc 0.5 sqm in each pane all as specified and directed.

M&L for solid PVC Door Frame of size 50mm x 47mm made out of 5mm prelaminated PVC sheet on single side reinforced with M.S. Square tube, supplying and fixing in opening as per specification and drawing all as specified and as directed.

M&L for factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top and bottom rails. M.S. frame shall be covered with heat moulded prelaminated PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and prelaminated PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail; Panelling of prelaminated PVC sheets on both sides to be fitted in the M.S. frame welded / sealed to the stiles and rails with suitable PVC sheet beading, and joined together with solvent cement, supplying and fixing in the frame at site as per specification and drawing all as specified and directed

S&F stainless steel butt hinges 100mm in size, medium weight, cold rolled all as specified and directed.

S&F aluminium anodised handles, 150mm in size, 'D' type, all as specified and directed.

S&F aluminium anodised handles, 100mm in size, fabricated type, all as specified and directed.

Supply only chain link fencing, any mesh, size and type all as specified and directed.

Fixing only chain link fencing including line wires, any mesh, size and type, fixed to any type of standards, rails, straining bolts, etc. including provision of binding wire all as specified and directed.

S&F Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, n exc 5cm long and 5 to 10mm dia shank bolt all as specified and as directed.

S&F Rolled mild steel in angle sections,fixed independently, without connecting plates, etc.and embeded in concrete post and struts in fencing including securing bolts including tops to shape as directed, drilling holes, flat iron fillets (for securing wire mesh) etc, conforming to Fe.410.Gde-E-250 all as specified and as directed.

S&F mild steel works in tubular trusses, rafters, purlins, etc. including special shaped washers etc. complete using ERW or induction butt welded tubes conforming to IS.1161-1979 grade St.-240 all as specified and as directed.

M&L for pre-painted galvalume coated high tensile corrugated/ trapezoidal profile steel sheets, AZ-70 coating mass, 550 Mpa yield strength, 0.5mm thick (TCT), as in roofing/ cladding fixed with self drilling fasteners as per manufacturers instructions all as specified and as directed. Note: Measurement shall be taken flat as fixed without any allowance for laps, etc.

S&F 4mm thick High Pressure Steam Cured (HPSC) non asbestos fibre cement building board in false ceiling with aluminum anodized snap grids of 60x60cm with Tee section 35x25x1.25mm, angle section 25x25x1.25mm thick including 2mm dia GI hanging wire including all hanger fittings etc and applying two coats of OBD on primer on exposed surface of ceiling all as specified and directed.

M&L for three coats of white wash on newly plastered walls, pilasters, cornices, etc. including necessary preparation of surfaces all as specified and directed.

M&L for two coats of cement based paint, any colour, on newly plastered surfaces of walls, pilasters, cornices, etc., including necessary preparation of surfaces all as specified and directed.

M&L for two coats of weather proof exterior acrylic emulsion paint over a coat of alkali resistant primer on newly plastered surfaces of walls, pillasters, roof projections, facias, drops, chajjas, etc., including necessary preparation of surfaces all as specified and as directed.

M&L for preparation of new steel surfaces over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer all as specified and directed.

M&L for 50mm bore GI water tubing, medium grade with and including provision of all fittings, fixed complete to walls and ceilings or laid in floors/ trenches all as specified and as directed.

M&L for 25mm bore GI water tubing, medium grade with and including provision of all fittings, fixed complete to walls and ceilings or laid in floors/ trenches all as specified and as directed.

S&F 20mm outer dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings, fixed complete to walls, ceilings or laid in floors all as specified and directed.

S&F 16mm outer dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings, fixed complete to walls, ceilings or laid in floors all as specified and directed.

M&L for double wall corrugated HDPE pipes, conforming to IS 14930-2001, ISI marked, 63mm outer dia, as in cable protection, fixed to poles/ walls with necessary MS clamps, bolts, nuts, washers or laid in trenches/ under roads/ crossing etc. all as specified and as directed.

M&L for GI tubes, light grade, 80mm bore, as in cable protection, fixed to poles/ walls with necessary MS clamps, bolts, nuts, washers or laid in trenches / under roads/ crossing etc. all as specified and as directed.

S&F 15 mm bore Bib tap, long body, brass chromium plated, fancy type with wall flange, with crutch or butter-fly handle, screwed down, screwed for iron pipe or for brass ferrule etc all as specified and directed.

S&F 15mm bore stop valves, brass chromium plated, fancy type, screwed down high pressure, with crutch of butterfly handle, screwed both ends for iron pipe for unions all as specified and as directed.

S&F pillar taps, brass chromium plated with capstan heads, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed down high pressure screwed for 15mm bore GI pipe all as specified and directed.

S&F 50mm bore gun metal gate valve heavy duty ISI marked with iron wheel head screwed both ends to iron pipes and fixed all as specified and as directed

S&F 25mm bore gun metal gate valve heavy duty ISI marked with iron wheel head screwed both ends to iron pipes and fixed all as specified and as directed

S&F 25mm dia PTMT ball valves high pressure with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe all as specified and directed.

S&F health faucet, brass chromium plated with 1m long flexible PVC tube and wall hook all as specified and as directed. Make: Continental series of JAQUAR or equivalent model in JOHNSON/ CERA

S&F vitreous china wash basin, white, size 550x400mm, including CI brackets and cutting for and pinning in ends of brackets or erecting stands etc. all as specified and directed.

S&F in vitreous china wash down water closet pan (pedestal pattern), white, including 'P' or 'S' trap, fixing bolts, etc, connecting to drain pipe and flushing pipe all as specified and as directed.

S&F 32mm bore x 900mm long LDPE pipes of pressure rating 6Kg/Sqcm and fixed complete to wash basin/ urinal all as specified and directed.

S&F PVC connection 15mm size with PTMT nuts, 450mm long all as specified and directed.

S&F valveless, syphonic action type low level PVC flushing cistern, 10 litres capacity, white, with inlet, ball valve, float, handle and flush pipe etc complete all as specified and directed.

S&F in 110 mm bore PVC (SWR) pipes, single socketed, in any length, with solvent cement joints, fixed to wall or laid trenches or in floors, all as specified and directed.

S&F in 150 mm bore PVC (SWR) pipes, single socketed, in any length, with solvent cement joints, fixed to wall or laid trenches or in floors, all as specified and directed.

M&L for bed concrete to 110mm bore drain pipes in Plain Cement Concrete 1:3:6 type C2 using 40 mm graded stone aggregate including packing under and haunching against the sides of pipe after they are laid and tested all as specified and directed.

M&L for bed concrete to 150mm bore drain pipes in Plain Cement Concrete 1:4:8 type C2 using 40 mm graded stone aggregate including packing under and haunching against the sides of pipe after they are laid and tested all as specified and directed.

Extra for forming fair finished drain or channel of 25cm inner girth in cement concrete using extra cement including forms moulds mitred / stopped end etc. all as specified and directed.

S&F PVC (SWR) floor trap plain with grating including jointing with solvent cement 75mm dia outlet all as specified and directed.

Cutting into existing manholes for connecting new drain pipes, 110mm bore, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished, and reforming benching as required all s specified and as directed.

M&L for sub main wiring with 2 runs of single core PVC insulated FRLS unsheathed multi-stranded copper conductor cables of size 6 sqmm drawn through and 1100 volt grade including PVC casing and capping of suitable size with all necessary fittings and provision of one run of 6 sqmm PVC insulated FRLS unsheathed multistranded copper conductor single core for earth continuity and connected to common earth dolly, complete all as specified and directed. Note: Two runs of 6 sqmm cable, one run of 6 sqmm earth conductor cable and one run of PVC casing and caping shall be measured and paid together as one unit length.

M&L for point wiring complete with 1.5 Sq mm single core PVC insulated FRLS unsheathed 1100 volt grade copper conductor multi-stranded cables drawn through and including PVC conduit pipes/ PVC casing and caping with all accessories and provision of one run of PVC insulated FRLS unsheathed 1100 volt grade copper conductor multi-stranded single core cable of size 1.5 sqmm and connected to common earth dolly including provision of suitable GI modular box flush mounted flush with wall alongwith modular frame and white cover plate for mounting modular switches/ sockets etc. for one light point controlled by one switch 1 way complete all as specified and directed. all as specified and directed.

All as described in item No. 143 but for one fan point controlled by one switch and regulator.

All as described in item No. 143 but for one 05 Amps socket outlet on independent board.

All as described in item No. 143 but for one 05 Amps socket outlet on the same board with other switches.

All as described in item No. 143 but wiring with 2.5 Sqmm single core PVC insulated FRLS unsheathed 1100 volt grade multi-stranded copper conductor cable and with one run of single core PVC insulated FRLS unsheathed 1100 volt grade multi-stranded copper conductor cable of size 2.5 Sqmm for earth continuity conductor and connecting to common earth dolly, complete for one 15 Amps power socket point on independent board all as specified and directed.

S&F modular switch, 1 module, 1 way, 6 Amps, 230 volts, AC, all as specified and directed.

S&F modular switch, 1 module, 1 way, 16 Amps, 230 volts, AC, all as specified and directed.

S&F modular socket outlet, 2 module, 6 Amps 2 cum 3 pin multipurpose all as specified and directed.

S&F modular socket outlet, 2 module, 16 Amps 3 pin 16 Amps cum 3 pin 5 Amps multipurpose all as specified and directed.

S&F in ceiling rose 3 terminal suitable for 230 volts AC supply all as specified and directed.

S&F modular fan regulator, step type, 2 module, 120 Watts, 230 volts, AC, all as specified and directed.

S&F 34 Watts LED glare free luminaire recess mounted in square profile 2ft x 2ft size with 34 W high brightness SMD LEDs for glare free homogenous illumination, including electronic driver etc. complete with all accessories internally pre wired including cutting of false ceiling sheet to required size and fixing aluminium strip as per the existing size in false ceiling for fixing of light fitting and providing aluminium strip supports as reqd and connecting up light fitting with twin core twisted flexible copper conductor cable of suitable size from ceiling rose to connector block all as specified and directed. Make: HAVELLS VENUS NEO HE 2x2 or equivalent in CG/ Philips/ Wipro

S&F 25 Watts LED security light fitting, with pressure die cast aluminium housing and lens embedded PC cover having top opening separate driver compartment with IP65 protection, 25 Watts high power LEDs, electronic driver including all accessories internally pre wired complete and connecting up light fitting with twin core twisted flexible copper conductor cable of suitable size from ceiling rose to connector block including provision of bracket made out of GI pipe light grade of suitable size and length and bent to shape fixed to walls/ poles with suitable MS clamps, bolt, nuts etc. complete all as specified and directed. Make: ENDURA PEARL model of HAVELLS or equivalent in Crompton Greaves/ Philips/ Wipro

S&F ceiling fan, 230 volts, single phase, 1200mm sweep, 3 blades, with all accessories complete all as specified and as directed. Make: HAVELLS Model No. ES-50 or equivalent model in Crompton Greaves/ USHA

S&F exhaust fan, 250mm sweep, 230/240 Volts, 1350 RPM, single phase, metallic finish powder coated, with wire grid protection and fixing arrangements with fixing bolts and provision of 3 core flexible copper conductor cable of size 1.5sqmm size from ceiling rose to connector of exhaust fan and testing all as specified as directed. Make: Havells VENTL-AIR DSP model or equivalent model in Almonard/ Crompton Greaves

S&F sheet metal enclosure type TP&N vertical Loadline DBs are fitted with Bus Bars, Neutral Links, Blanking plates (without MCCB) 12 ways with double door type and including provision of 2nd class hard wood board with sunmica top of suitable size fixed to wall and fixing of the MCB DB on board complete all as specified and directed.

S&F MCCB TP 125 Amps ,35KA, 415 Volts, AC supply, fixed thermal magnetic settings, all as specified and as directed.

S&F sheet metal enclosure MCB DB SPN 8 way fitted with 200 A rated Bus Bars, double door type and including provision of 2nd class hard wood board 4mm thick with sunmica top of suitable size fixed to wall and fixing of the MCB DB on board complete all as specified and directed.

S&F MCB DP 63A 'C' series 10KA 50Hz 240 Volts AC supply all as specified and as directed.

S&F MCB SP 5-32A 10KA 'C' series 50Hz 240 Volts AC supply all as specified and as directed.

Earthing complete with galvanised steel earth plate electrode 60cmx60cmx6mm thick, burried directly in ground vertically (earth pit not less than 2.25 metre deep below normal ground level) with top edge of the earth plate at a depth not less than 1.5m below normal ground level connected to GI wire 4mm dia (7.5m long) by means of GI bolts nuts washers and GI wire protected by 15mm dia light grade GI pipe (7.5m long) and watering arrangements with 20mm dia GI pipe medium grade and GI funnel all as specified and shown in Electrical Plate No 3 of MES Schedule Part I including necessary excavation and earth work in any type of soil, charcoal, dust salt, PCC 1:2:4 type B1 in chamber, 40mm thick RCC 1:2:4 type B1 in cover slab with 8mm dia TMT bars at 100mm C/C both ways and with 8mm dia MS hook complete and testing all as specified and directed.

M&L for 1000 litres capacity rotational moulded polyethylene (HDPE) water storage tanks, 'ISI' marked, cylindrical, vertical with closed top conforming to IS 12701-1989 having two layers wall construction with manhole lid and suitable locking arrangement including making holes for inlet, outlet and over flow pipes, hoisted and fixed in position including testing complete all as specified and directed.

M&L for XLPE insulated, armoured, heavy duty electric LT UG cable with multi-stranded aluminium conductor, 1100 Volts grade, cross sectional area 35Sqmm x 4 core, laid in trenches/ passing through pipe/ duct or fixed to wall including provision of necessary lugs/ thimbles/ ferrules, connecting up , testing and commissioning complete all as specified and as directed. Note: Excavation, earth work, cable cushioning, bricks/ GI pipe for protection shall be measured and paid separately under relevant items of this schedule.

M/s. N D KALING

RAJENDRA KRISHNA SARAF

ASHIRWAD ELECTRICALS

ASHOK M RAJGOLKAR

DHANSHRI ENTERPRISES

M/S MAHADEV M PATIL

RAJARAM TAYAPPA DANDAGALKAR

M/s NEELAM ELECTRICALS