Provn of New JCOs Living for 04 x JCOS Near Bldg No T-12 Alongwith Toilet, Bathroom With Geysers of B MED Regt and Provn of Shed for Placement of Refreshment Stalls for UFO During Movie Shows at Sarvatra Cinema Hall of C Arty Bde at Faridkot Mil Stn

Amount

Excavation in trenches in soft/loose soil not exceeding 1.5m deep and 1.5m wide, for foundation etc or manholes,piers,shafts etc not exceeding 10 Sqm on plan and getting out complete all as specified and directed.

Excavation over areas not exc 1.5 m in deep and getting out in soft/loose soil complete all as specified and directed.

M&L PCC 1:4:8 type D2 (using 40mm graded crushed stone aggregates) as in foundation, filling and mass concrete complete all as specified and directed.

M&L for Reinforced cement concrete M-30 (design mix) (using 20mm graded crushed stone aggregates) as in foundation including rafts, footings, foundations beams; plinth beams, bases for column etc; basement slabls, under-reamed piles and mass concrete complete all as specified and directed

M&L for Reinforced cement concrete M-30 (design mix) (using 20mm graded crushed stone aggregates) as in column, pillars, piers, posts and sturts complete all as specified and directed

M&L for providing Reinforced cement concrete M-30 (design mix), (using 20mm graded crushed stone aggregates) as in lintels upto 1.5 mtr clear span, siesmic band and similar works including necessary form work complete all as specified and directed

M&L for providing Reinforced cement concrete M-30 (design mix), (using 20mm graded crushed stone aggregates) as in slab supported on walls, beams, columns,landings,balconies, canopies,deck slabs and in shelves and other similar works complete all as specified and directed and directed .

M&L for providing Reinforced cement concrete M-30 (design mix), (using 20mm graded crushed stone aggregates) as in chajjas complete all as specified and directed and directed .

M&L for use and waste of formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits of foundation and plinth beam and similar work vertical or to batter complete all as specified and directed.

M&L for use and waste of form work to sides of pillars,struts,piers and columns square/rectangular for rough finished surfaces complete all as specified and directed.

M&L for use and waste of form work to sides and soffits of floor or roof beams, beam hunching, girders, lintels, cantlievers, shelves including supports, etc for rough finished flat surfaces of concrete complete all as specified and directed.

M&L for use and waste of form work to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200 mm thick (Horizontal or slopping) for rough finished flat surfaces of concrete complete all as specified and directed .

M&L for use and waste of formwork to edges of concrete flats, treads, breaks in floors,window cills, concrete railings, openings in concrete walls, floor and roofs, n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10cm but n. exc 20cm wide fair finished surface complete all as specified and directed .

M&L for Mild steel TMT bars 10mm dia and over, cut to length, bent to shape as required, including cranking, bending and binding with & including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed .

M&L for Mild steel TMT bars 5mm dia and over upto 10mm dia,in stirrups,spacers and binders, cut to length, bent to shape as required, including cranking, bending and binding with & including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed .complete all as specified and directed.

M&L for brick work with fly ash bricks,straight or curved on plan, exceeding 6m mean radius using old size bricks in wall built in cement mortar 1:6 complete all as specified and directed.

M&L Brickwork with sub class 'B' bricks, straight or curved on plan to any radius in half brick thick walls using old size bricks, built in cement mortar 1:4 complete all as specified and directed .

M&L for Anti termite treatment for treating the backfill in contact with foundation @ 7.5 Litres of emulsion per sqm of vertical surface complete all as specified and directed

M&L for Anti termite treatment for treating the top surface of filled earth @ 5 Litres of emulsion per sqm of surface complete all as specified and directed

M&L for Anti termite treatment for treating the soil under plinth protection @ 5 Litres of emulsion per sqm of surface area complete all as specified and directed

M&L for Anti termite treatment for treating the soil along with external perimeter of building @ 2.25 Litres of emulsion per meter of the perimeter wall complete all as specified and directed

M&L for polythene film, 300 micron thick, laid on a coat of bitumen primer, @ 0.30 to 0.50 kg per sqm conforming to IS specification with lap joints 100mm wide complete all as specified and directed

M&L for Returning, filling in including spreading, leveling watering and well ramming in layers not exceeding. 25cm thick each complete all as specified and directed.

M&L for Removing excavated material to a distance n.exc 50 m & depositing where directed at a level n.exc 1.5 m above the starting point complete all as specified and directed .

M&L for hard core of gauge exceeding 63mm but not exceeding 100mm using broken stone or boulders, deposited, spread and leveled in layers not exc 15cm thick, watered and rolled/rammed to a true surfaces complete all as specified and directed .

M&L for 100mm thick plain cement concrete 1:4:8, type D-2 (using 40 mm graded crushed stone aggregates) as in flooring, sub base,mass filling complete all as specified and directed.

M&L for 25mm thick plain cement concrete 1:2:4 type B-0 (using 12.5mm graded crushed stone aggregates) as in flooring complete all as specified and directed

S&F Non skid ceramic coloured tiles (light colour as approved) 7 to 8 mm thick (square/rectangular), area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm in floors etc, set and jointed in neat cement slurry and pointed in white cement with pigment to match the colour of tiles over & including 15mm thick screed in cement mortar 1:4 complete all as specified and directed

S&F Non skid coloured ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm on vertical surface such as skirting / dados set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade over & including 15 mm thick rendering in cement mortar 1:4 complete all as specified and directed.

S&F Glazed ceramic coloured tiles 450mmx300mmx7mm thick (colour and shade as approved) as in vertical surfaces such as skirting/dados etc, set and jointed in neat cement slurry & pointed in white cement with pigment to match the colour of tiles over & including 15mm thick rendering in cement mortar 1:4 complete all as specified and directed

S&F Machine cut kota stone slab in flooring,cill ,20-25mm thick laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing,cutting and mirror polishing complete all as specified and directed. Note:- Single piece of kota be used in the treads of staircase.

S&F Machine cut kota stone slab 20-25 mm thick as in skirting,steps,dado,& pillars, set and jointed in cement slurry and pointed in cement mixed with pigment to match the shade of slab including rubbing, cutting and mirror type polishing complete all as specified and directed . Note:- Single piece of kota be used in the risers of staircase.

M&L for rendering 15 mm thick in cement mortar 1:6 on other than fair faces of brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified and directed .

M&L for rendering 10 mm thick in cement mortar 1:3 on ceiling, surface finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 15mm thick in cement mortar 1:4 on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified and directed .

M&L for washed stone grit plaster on exterior walls in two layers, under layer 12mm cement plaster 1:4 (1 Cement : 4 Coarse Sand) the under layer with scratching tool, applying cement slurry on the under layer @ 3 Kg of cement per square meter, top layer 15mm cement Plaster 1:1/2:2 (1 Cement : 1/2 Coarse sand : 2 Stone chipping 10mm nominal size) in panels with grooves all round as per approved pattern including scrubbing and washing, the top layer with brushes and water to expose the stone chippings complete all as specified and directed. Note : Payment for providing grooves shall be made separately)

M&L for Forming groove of uniform size 15mm wide and 15mm deep in the top layer of washed stone grit plaster as per approved pattern using wooden battens, nailed to the under layer including removal of wooden battens, repair to the edges of panels and finishing the groove complete as per specifications and direction of the Engineer-in-charge

M&L for preparation of newly plastered or unplastered surfaces of wall and applying two coat of distemper oil emulsion (white/tinted) after finishing the surfaces with a coat of wall care putty by hand roller complete all as specified and directed .

M&L for preparation of newly plastered or unplastered surfaces of ceiling and applying two coats of white wash complete all as specified and directed .

M&L for preparation of newly plastered or unplastered surfaces of wall and applying two coat of cement base paint complete all as specified and directed .

S&F Pressed steel pre coated frames of size 105 x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc.complete all as specified and directed.

S&F Pressed steel pre coated frames of size 125 x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc.complete all as specified and directed

Framed work such as grills, gratings etc. with ends of bars shoulderd and/or riveted, or forged into spikes, framed guard bars, barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks,cooler stand and similar work conforming to Fe290, Gde-E-165 complete all as specified and directed.

S&F 35 mm thick 2nd class hard wood, plain, framed, panelled shutters (any number of panels) with panels of timber flat on both sides (feather edges) or of vaneered partical board medium desnsity, wood partical board with commercial face veneers fitted to chowkats complete all as specified and directed

S&F 35 mm thick 2nd class hard wood, glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); fitted to chowkats complete all as specified and directed .

S&F factory made steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded all as specified and directed .

S&F factory made steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete without glazing bars, dovetailed or welded all as specified and directed.

S&F Steel windows or ventilators, fixed type, with glazing bars complete all as specified and directed

M&L for 3 mm thick, plain sheet glass, ordinary quality and glazing with oil putty or with wooden beads in squares n.exc 0.5 sqm each pane complete all as specified and directed .

S&F galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks or galvanised wire staples complete all as specified and directed .

S&F 3mm thick, figured glass, pin head type and glazing with oil putty in squares n exc 0.5 sq. m in each pane complete all as specified and directed .

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/ Chowkhat of size 45 x 85 mm comprising of virgin PVC polymer, calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum and screw withdrawal strength of 2200 N (Face) and 1100N (edge), minimum compressive strength 58 N/ mm ² ,modules of elasticity 900 N/mm ² and resistance of spread of flame of Class A category with property of being termite/borer proof,water/moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete all as specified and directed.

S&F Factory Made Solid PVC Moulded Door Shutter, with particle board core, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick moulded prelam PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing all as specified and directed

S&F 100mm stainless steel butt hinges fixed with stainless steel screws complete all as specified and directed.

S&F Aluminium anodised, cast type, handle 150 mm size complete all as specified and directed.

S&F aluminium anodised barrel tower bolts,200 mm long of extruded section, fixed to doors with screws complete all as specified and directed .

S&F aluminium alloy, anodised, sliding door bolt of length 250mm with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded section and fixing bolt and sliding bolts of extuded sections or cast aluminium alloy and fixed complete all as specified and directed .

S&F mild steel 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed .

S&F 140 mm floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and directed .

M&L for preparation of new or previously untreated steel surface of any description over 10cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M&L for preparation of new or previously untreated surface of wood or wooden based surfce of any description not other wise described over 10 cm width or girth and applying two coat of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

S&F MS powder coated decorative drapery rod (colour as approved) 20mm dia of approved pattern & design including decorative knobs (wall side and free side) & powder coated mild steel flat iron brackets fixed with steel screws & PVC rawl plugs/grips complete all as specified and directed.

M&L for PCC 1:3:6, type C0 (using 12.5mm graded crushed stone aggregates) as in back filling of pressed steel frames, bed blocks, fixing of hold fasts etc including necessary formwork complete all as specified and directed

M&L for rendering 10 mm thick in cement mortar 1:3 on fair faces of brick work or concrete surfaces as in roof complete all as specified and directed .

M&L PCC 1:2:4 type B-0 (using 12.5mm graded crushed stone aggregates) as in roof kerbs in concave shape, rounded or chamfered angles complete all as specified and directed.

M&L for Roof Treatment as specified below and as directed : (a) Applying one coat of PrimeSeal/ Epoxy Primer/ShaliUrethane BTD White diluted with potable water in the ratio of 1:1 and apply @ 0.40 kg/ sqm (0.20 kg BTD+0.20 Kg water) (b) Laying polyster reinforced fiber net/50 gsm Geotextile mesh, upto 300 mm on walls. (c) Applying three coat of HydroShield PUD microfibre reinforced UV resistent polyurethane (solid content 68% ) / Damp Proof ultra UV Stable fibre reinforced elastomeric liquid waterproofing membrane formulated with PU hybrid polymers (Solid content 55%)/ SmartCare PU Magnum elastomeric waterproofing coating based on hydrophobic polyurethane (solid content 85%)/Single Component Elastomeric Liquid Membrane ShaliUrethane BTD White/coloured (Elongation 400% ± 50, Solid Contents > 80% & Specific Gravity @ 30 OC 1.5 ± 0.03) @ total 2.00 Kg per sqm in two coats for maintaining thickness of 1.5mm, with paint brush/ roller upto 300 mm on walls. (d)) Complete treatment to be carried out by authorised applicator of waterproofing manufacturer. Note : (i) The treatment shall be carried out as per the manufacturers instructions, and as directed by Engineer in Charge. (ii) The plan area of floor shall be considered for payment

M&L for 75 mm thick cement concrete 1:3:6 type C2( using 40mm graded crushed stone aggregates) as in plinth protection finishing surfaces even and fair complete all as specified and directed .

S&F vitreous china wash down water closet pan (pedestel pattern) white in colour including connection pipe to union of flushing cistern, inlet and overflow pipes,connecting only to flushing cistern, anti-syphonage pipe with PVC flush pipe of 32mm dia including plastic seat with cover,white in colour with mild steel chromoum plated hinging and 'P' or 'S' trap device complete all as specified and directed.

S&F 10 litres PVC,valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets complete all as specified and directed.

S&F vitreous china Wash hand basin, white, flat back of size 550x400mm including cutting for and pinning in ends of brackets or erecting stand including CI brackets,Brass chromium plated waste coupling 32mm bore, Waste pipe PVC 32mm bore, complete all as specified and directed.

S&F PVC connection, 15mm size with PTMT nuts of length 450mm complete all as specified and directed.

S&F rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) 500 Ltr capacity,trippled layered, hoisted and fixed in position including PTMT float valves, high pressure with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed in position including all necessary fittings complete all as specified and directed..

S&F gun metal globe or gate valve with iron wheel head, screwed both ends for iron pipe & fixed for 15 mm dia of pipe complete all as specified and directed.

S&F Stop valve, cast copper alloy, screwed down for high pressure with crutch or butter fly handle, screwed both ends for iron pipe of 20mm bore complete all as specified and directed .

S&F gun metal globe or gate valve with iron wheel head, screwed both ends for iron pipe & fixed for 25 mm dia of pipe complete all as specified and directed.

M&L for Steel water tubing of 25 mm bore, medium grade, galvanised, with all fittings, laid in trenches/ fixed to wall etc complete all as specified and directed .

M&L for Steel water tubing of 15 mm bore, medium grade, galvanised, with all fittings, laid in trenches/ fixed to wall etc complete all as specified and directed .

M&L for Steel water tubing of 20 mm bore, medium grade, galvanised, with all fittings, laid in trenches/ fixed to wall etc complete all as specified and directed .

S&F bib tap cast copper alloy ,chromium plated with crutch or butter fly handle, screwed down, screwed for 15mm bore pipe & fixed complete all as specified and directed .

S&F Brass Chromium plated wall mixer for mixing hot & cold water screwed down for 15mm bore iron pipe (as per sample) complete all as specified and directed.

S&F brass chromium plated Centre hole Basin Mixer, swan neck type for mixing of hot & cold water screwed down for 15mm bore iron pipe complete all as specified and directed .

S&F Stop valve/angle ball, cast copper alloy,fancy type,chromium plated, screwed down for high pressure with crutch or butter fly handle, screwed both ends for iron pipe of 15mm bore complete all as specified and directed .

S&F Shelf of PTMT, fixed with and including chromium plated brass screws and wooden/plastic cleats (Minimum weight 300gms) complete all as specified and directed.

S&F Tubular towel rail, brass chromium plated, 20mm dia, D type, 60cm long between flanges fixed with CP brass screws including wooden/plastic beads complete all as specified and directed .

S&F CP Toilet paper Holder Brass finish glossy fixed to walls with chromium plated (CP) brass screws complete all as specified and directed.

M&L for water proofing treatment to RCC sunken slab as specified below and as directed by Engineer in Charge:- (a) Cleaning the surface with wire brush / coir brush, removing loose material like dust particles, dirt etc. (b) Rendering 10 mm thick in cement mortar 1:3 using water proofing compound on raised vertical surfaces. (c) Creating fillet covering of 50 x 50 mm with polymer modified mortar on the junction of slab and wall (d) Apply first coat of two component modified polymer coating on the horizontal and vertical surface. (e) Provision of glass fiber mesh of 2 x 2 mm immediately on above coating. (f) Apply second coating of two component modified polymer coating after 72 hrs. (g) Laying concrete 1:4:8 over the coating as per requirement. (h) Joining the sanitary pipes with the waterproofing tape having bridging ability of more than 1.5 mm (j) Filling the gap between the wall opening and sanitary pipe with non shrink cementatious grout. (k) Complete treatment to be carried out by authorised applicator of waterproofing manufacturer. Note : (i) The treatment shall be carried out as per the manufacturers instructions, and as directed by Engineer in Charge. (ii) The plan area of floor shall be considered for payment

S&F 110mm bore PVC (SWR) pipes, single socketed in any length with rubber ring joints, laid in trenches/in floors/fixed to walls including fixing clamps with nut and bolts complete all as specified and directed .

S&F 75mm bore PVC (SWR) pipes, single socketed in any length with rubber ring joints, laid in trenches/in floors/fixed to walls including fixing clamps with nut and bolts complete all as specified and directed .

M&L for PVC (SWR) floor trap, 75 mm bore, plain with grating including jointing with solvent cement fixed to wall/laid in trenches etc complete all as specified and directed .

S&F PVC (SWR) bends, any radius, 110 mm bore complete all as specified and directed .

S&F PVC (SWR) bends, any radius, 75 mm bore complete all as specified and directed .

S&F PVC (SWR) vent cowl of bore 75mm complete all as specified and directed

M&L for providing and fixing stainless steel (Grade-304) railing, made of hollow tubes,channels,plates etc including welding,grinding,buffing,polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners,stainless steel bolts,decorative elements etc, of required size including making groove /drill with suitable fixing arrangement in RCC floor/staircase/brick wall complete all as specified and directed .

S&F pressed steel rectangular frames for built in cupboard doors, made out of mild steel sheet 1.0mm thick with girth of frame 185mm including MS rawls plugs and fixing 100mm long butt hinges, medium weight, cold rolled, mild steel etc including two coats of synthetic enamel paint over a shop coat of zinc chromate primer complete all as specified and directed.

S&F pressed steel door shutters including stiffeners made out of mild steel sheet 1.0mm thick, cut to size, holes punched and welded seams including bending or turning up all around, mitered angle, one no locking arrangement as per Godrej pattern, two nos handle and applying two coats of synthetic enamel paint over a shop coat of zinc chromate primer complete all as specified and directed Note : (i) Measurement of door shutter shall be taken as exact size of cupboard opening (excluding frame and folded/ turned up portion) (ii) Stiffeners of 150mm girth and height equal to height of shutter made to shape as directed by Engr-in-charge. cost of these stiffeners shall be deemed to be included in the unit rate quoted for door shutters and no extra measurement/payment shall be made for the same.

M&L for Concrete bed to drain pipes of dia 150mm in cement concrete 1:4:8 type D-2 (using 40mm graded crushed stone aggregate) including packing under and haunching against the sides of pipe after laid & tested complete all as specified and direced .

S&F Reinforced concrete pipes of size 150mm (internal dia),class NP-2 (ISI marked) laid, jointed and tested complete with collar complete all as specified and directed .

Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2) round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished, and reforming benching as required (Internal Dia of pipe in 150mm) complete all as specified and directed.

M&L for Pre cast cement concrete 1:2:4, type B-1 (using 20mm graded crushed stone aggregate) as in manhole cover slab, rounded or chamfered on edge included neccessary formwork, set in cement mortar 1:4 complete all as specified and directed .

Surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out in any type of soil complete all as specified and directed

M&L for sand filling under floor with washed and screened dry fine river sand including watering, well ramming and consolidation complete all as specified and directed.

M&L machine pressed, precast concrete interlocking coloured paver block, any shape and size confirming to IS-15658-2006 of 60mm thickness, M-35 Grade with grey cement and pigment complete all as specified and directed .

S&F factory made precast kerb stones in PCC 1:2 :4 type B-1 including chamfers, weatherings,throatings etc in smooth finish & set in cement mortar 1:4 including necessary excavtion and earth work for embedding kerb stone at a depth as directed and temping around kerb stone and removal of surplus soil to a distance not exceeding 50 m and depositing where directed complete all as specified and directed .

Excavating in post holes each not exc 0.50 cum, getting out in soft/loose soil, returning, filling in and ramming earth or broken rubble mixed with earth around, in layer not exc 25cm and removing surplus soil to a distance not exc 50m and making good surface all as specified`and directed .

M&L PCC 1:3:6 type C2 (using 40mm graded crushed stone aggregates) as in foundation, filling and mass concrete complete all as specified and directed.

S&F rolled mild steel in joist,channel,angle,or tee sections,fixed independently,without connecting plates,etc(cut to ordinary lengths) including welding conforming to Fe-290 Gde E-165 quality complete all as specified and directed.

S&F Pre painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.5 mm thick of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall fixed with self tapping screws complete all as specified and directed .

Point wiring complete with 1.5 sqmm single core PVC insulated unsheathed cable(ISI marked) 1100 volts grade FRLS with multistranded copper conductor, drawn through concealed / surface in wall / roof/ceiling surface and its accessories on the surface etc including PVC rigid concealed conduit of suitable size with all accessories such as bend, reducers, MS hooks, MS junction boxes, 2mm thick galvanised steel pressed sunken terminal boxes of suitable sizes for mounting of switches, sockets, fan regulator etc, covered with 2.8mm thick plastic laminate Hylem / Anchor top cover sheet of required colour, fixed with brass screws and cup washers, painting terminal boxes inside and outside with one coat of red oxide primer including continuous earth wire of size 1.5 Sqmm PVC stranded copper conductor unsheathed, insulated, stranded (Green colour) connected to common earth point dolly for One light point/ fan point/ exhaust fan point to be controlled by one number one way switch complete all as specified and directed .

All as per Srl item No. 109 here-in-before but for one three pin socket outlet 5 Amp on the same board with other switches complete all as specified and directed.

All as per Srl item No. 109 here-in-before but for one switch socket combination, 3 Pin 5 Amps, 230 Volts on independent board complete all as specified and directed.

All as per Srl item No. 109 here-in-before for switch socket combination (multi purpose) 6 Pin 15 Amps 230 volts point to be controlled by one switch and wiring with 2.5 Sqmm FRLS PVC unsheathed copper conductor and FRLS cable 2.5 Sqmm PVC insulated earth wire on independent board.complete all as specified and directed .

S&F PVC Lamp holder with back plate suitable for batten fittings complete all as specified and directed .

S&F LED bulb 1x10 watt having luminous efficiency warranty 2 years complete all as specified and directed .

S&F complete set of tube light fitting, 1x20 watt LED (4 feet long) 230 volt, decorative ultra slim linear LED lighting fixture with environment friendly, energy efficient ready to use pack etc with all acessories such as LED adopter, LED tube, internally prewired and including connecting up with twin core twisted flexible copper conductor cable of suitable size complete all as specified and directed

S&F complete set of tube light fitting, 1x10 watt LED (2 feet long) 230 volt, decorative ultra slim linear LED lighting fixture with environment friendly, energy efficient ready to use pack etc with all acessories such as LED adopter, LED tube, internally prewired and including connecting up with twin core twisted flexible copper conductor cable of suitable size complete all as specified and directed

S&F ceiling rose, three terminals, PVC polycarbonate, isolated body with bakalite 20mm back plate complete all as specified and directed.

S&F switch piano, flush type, single pole, one way, 5/6 Amps, 230 volts, AC supply complete all as specified & directed

S&F socket outlet, two-in-one, 5 pin, 5 Amp, 230 volts, AC supply complete all as specified & directed

S&F switch piano, flush type, single pole, one way, 15/16 Amps, 230 volts AC supply complete all as specified and directed

S&F socket outlet ,2 in 1, 5/6 pin, 15/16 Amps, 230 volts ,AC supply complete all as specified & directed

S&F sub main wiring with two runs of single core PVC, FRLS sheathed, insulated, copper cable of 6 Sqmm size, multi stranded, 1100 volts grade with PVC insulated FRLS copper wire 6 Sqmm for continous earth wire drawn into and including concealed conduit of suitable size not less than 20mm dia complete all as specified and directed . Note :- Two runs of 6 Sqmm copper cable and one run of 6 sqmm copper wire earth continuty conductor & conduit with accessories shall be measured as one length)

S&F factory made epoxy polyester powder coated distribution board TP&N ,4 ways (VTPN DB), double door,(concealed flush to wall) (IP-42 protection) fabricated from minimum 1.2 mm thick CRCA sheet and fixed on wall and suitable for universal mounting and including 250 Amps bus bar, neutral bar, standard DIN rail, earth bar and cable ties for cable management, top and bottom removable gland plates with space for provision for 4 pole MCCB as incommer and outgoing MCBs as required at site and conforming to IS: 8623 along with cable end box including making good disturbed surface complete all as specified and directed. NOTE: (a) MCCBs and MCBs shall be measured and paid separately.(b) All cables terminating into MCBs shall be connected by using suitable copper lugs/thimbles/sleeves and its cost shall be deemed to be included under respective item of BoQ..

S&F MCCB, 4 Pole,adjustable type ,415 V, 63 Amps with breaking capacity 16 KA including making good the disturbed surfaces complete all as specified and directed.

S&F Sheet metal enclosure for DBs,SPN, double door, 230 Volts,8 ways with 200 amps rated bus bar complete all as specified and directed .

S&F MCB, SPN, 32 amps, 230V, C Series with breaking capacity 10 KA complete all as specified and directed

SS&F MCB SP 5 to 32 Amp, 230 volts, B Curve with breaking capacity 10 KA complete all as specified and directed

M&L for Earthing complete with galvanized steel earth plate electrode 60cmx60cmx6.00mm thick, buried directly in ground vertically (depth of pit not less than 2.25m below normal ground level), with top edge of the plate not less than 1.5m below normal ground level, earth plate surrounded by 15cm thick and packed alternate layers of charcoal dust and common salt, connected with and including earth lead of GI wire 4mm dia (8SWG) by means of bolts, nuts, check nuts and washers of galvanized iron or thimbles and other end of the earth wire connected to electrical equipment/GOD/LA and protected by galvanized iron pipe light grade 15mm dia bore including watering pipe 20mm dia bore GI medium grade (ISI marked) with funnel and wire mesh, including all necessary excavation and earth work, PCC chamber in plain cement concrete (1:3:6) type C-1 and pit cover of precast RCC with MS frame etc and all as shown in electrical plate No 3 of MES Schedule Part-I (2009), complete all as specified and directed. Note(s):- (i) RCC pit cover shall be pre-cast of RCC (1:2:4) type B-1, 80mm thick reinforced with XPM not less than 4Kg/Sqm. (ii) PCC chamber shall be constructed 1000 mm away from the edge of earth pit. (iii) Rate shall include earth lead and protection pipe of length 7.5m, excess beyond 7.5m length required at site shall be measured and paid separately. (iv) Earth resistance should be less than 3Ohm. In case the test results are not found below 3Ohm, complete earthing will be redone without any extra cost to Govt. (v) Quoted lump sum / rate shall be inclusive of above all provisions.

S&F in repair GI pipe, light grade, 40mm bore, for cable protection, fixed to pole/wall with MS clamps, nuts, bolts etc or laid under floor/road/pavement complete all as specified and directed. Note : (i) Excavation and earth work shall be measured and paid separately.

S&F exhaust fan ,steel body, AC single phase, 4 blades with self closing GI louver shutter suitable for operation on 220/230 volts of 300mm sweep and including three core copper flexible wire 1.00 mm dia drawn into and including PVC flexible conduit and hanging on wall with 4 Nos steel fasterners 10mm dia & 100mm long including wall hole and making good the disturbed surfaces as per existing complete all as specified & directed

S&F 1X10 watt LED retrofit type bulk head fitting luminaries, die cast, aluminium alloy body, heat resistant, prismatic glass cover with specially designed gasket, lamp holder etc complete with all accessories and including connecting up with twin core twisted flexible copper coductor cable with suitable size of 230 volt,50 HZ complete all as specified and directed.

S&F energy efficient LED Security light fitting of 25W, pressure die cast aluminium housing/body, heat resistant clear toughened glass, better optics for uniform distribution street/ roadway luminaire, with driver including electric connection, complete fitting with all accessories on and including bracket of 40mm dia,light grade ,GI pipe ,1.20 m and connecting with twin core twisted flexible copper conductor cable 1.5 Sqmm and with following specifications complete all as specified and directed :- (a) Lumen system efficacy of luminaire should be minimum 100 Lumen per watt. (b) Input Voltage range : 140 to 270 volts (c) Temp operating range : Minus 10°C to Plus 50°C (d) Power factor : Minimum 0.95 (e) THD : Max15%. (f) IP rating : IP66. (g) IK rating : Minimum IK07 (h) Built in potted LED Driver of the same make as of the luminaire. (j) LED driver should be complete with all protections viz open/short circuit protection, over voltage protection, all as per standard design of manufacturer. (k) Surge protection 10 kV (inbuilt + extended) (l) CCT : 5700 K. (m) CRI : Morethan 80 (n) Lens - High Efficiency wide angle lens. (o) BIS Approved fixtures and driver (p) Rated life time : 50000 burning hrs (Average 10 to 12Hrs

Supply, fixing & hanging Energy efficient Ceiling fan (white colour) 1400mm sweep BEE approved 5 star rating, AC single phase, 230V, min air delivery 245 CFM with service value 6.00 including canopies,electronic regulator , three Nos. blades, down rod, double ball bearing with capacitor 2.5 mfd and making connection with and including PVC insulated PVC sheathed copper conductor flexible cable 3 core of suitable size from ceiling rose or connector to fan complete all as specified and directed .

Supplying and fixing and commissioning of electric water heater (Gyser) storage type ABS body of capacity 25 ltrs, BEE appreoved 5 star rating, 230V,single Phase, AC supply inner tank made out of heavy duty stainless steel sheet (Designed with single weld line, factory tested with hydraulic pressure as per latest IS code) with glass lined quoting complete with all accessories such as safety valve thermostate NRV, connection piece PVC connection for hot and cold water 3 core PVC insulated PVC sheated copper conductor flexible cable including 15 Amp plug suitable for existing socket and fixing material, 04 Nos nut bolt grouting in wall in PCC(1:2:4) using 12.5mm graded stone aggregate for hanging the geyser and making good the disturbed surface complete all as specified and directed

Supply, installation, testing and commissioning of desert cooler electric driven (single phase) having nominal air flow capacity of 6000 CuM Per hour (or nearest size) in steel body made out of hot dip galvanised steel plain sheet thickness 1mm body and 1mm thick removable sides and back panels, single phase 230 volts of exhaust fan size 450mm sweep with submersible pump of suitable size / capacity (ISI marked) (maximum power consumption 250 Volts), PVC grills, conecting copper cable with three pin top, length not less than 2.0 m, PVC connecting pipe of suitable length, BEE approved, conforming to trade pattern including 15mm bore float valve & PVC connection, leakage proof joints complete all as specified and directred.

M&L for sand cushioning with a layer of dry river sand, 80mm thick before laying of cable and 150mm thick (punned down to 100mm thick) after laying of cables, in trenches/ducts, complete all as specified and directed. Note : Punned down thickness (overall 18cm), shall be considered for measurement and payment.

Supplying and laying, factory made unreinforced precast concrete cable cover LV type-1, flat, of size 250x150x40mm, laid flat and dry in trenches over the cable for protection, length perpendicular to the direction of cable adjacent to each other, complete all as specified and directed.

Supply, laying, jointing, testing and commissioning of Low Tension (LT) XLPE insulated, armoured, heavy duty, electric power cable, cross sectional area 10 Sqmm, 2 core, aluminum conductor, 1100 volts grade under ground cable including both side connection with lugs/thimbles of suitable size etc, laid in trenches, along poles or passing through pipes or laid under floor or through walls etc, complete all as specified and as directed. Note: (i) Returning filling, earth work, sand cushioning and brick cover for protection of cable shall be measured and paid separately.

BANSAL BUILDERS

N.G BUILDERS

M/S BSS AND SONS

GS and Co

M/S RAJESH KUMAR and CO.