Construction of B.T. road from and drain raising with cover slab from Suriya wine shop near Cement Shop to Kazi Bazar Chhack in Ward No. 14.

Dismantling and removing cement concrete including stacking the useful maternals and reuse and removing the debirts within 50m lead etc complete

Disposal of surplus excavated materials by truck to low land area incl. loading and unloading etc. complete.

Providing, laying, spreading and compacting stone aggregates using IRC GR-II size granite metal to Water Bound Macadam specification Including spreading in uniform thickness, hand packing, rolling with 3 wheeled steel roller 8-10 tonne in stages to proper grade and camber. applying and brooming requsite type of screening / blinding materials as crusher dust to fill up the interstices of coarse aggregate, watering and compacting to the requred density as per clause 404 of MOSHT&H Specifications for Road & Bridge works (4th Revision

Providing and applying primer coat with bitumen emulsion on prepared surface of granular Base including clearing of road surface of granular base including cleaning of road surface and spraying primer at the rate of 0.6 Kg/sqm using mechanical clause 502 of MOSRT & H specifications for raod and bridge works(4th revision

Providing and applying tack coat with bitumen emulsion on prepared surface of granular Base including clearing of road surface of granular base including clearing of road surface and spraying primer at the rate of 0.0 Kg/sqm using mechanical clause 502 of MOSRT & H specifications for raod and bridge works(4th, revision

Labour for scraping and cleaning the road surface, applying tack coat using 3.0kg of bitumen for 10sqm and laying 75mm thick built up spray grouting in two layers 37.5mm thick each layer using 0.45cum of 25mm to 40mm size hard granite metal and 12.00Kg penetration grade of bitumen for 10 Sqm in each layer with 0.12cum of 12mm size hard granite chips as key stone for 10 Sqm spreading over and laying including heating pouring and spreading over and spreading bitumen metal and chips and rolling with PRR including hire and running charges of PRR and all other machineries but excluding cost and conveyance of bitumen, metal and chips complete as per specification and direction of Engineer-in- Charge.

Providing and laying dense graded bituminous macadam with 60-70 TPH hot mix plant using crushed aggregates of specified grading premixed with bituminous binder, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per clause 507 of MOSRT&H specifications for Road&Bridge works (4th Revision)

Providing and laying semi dense bituminous concrete with 100-120 TΡΗ batch type HMP producing an average output of 75 tonnes per hour using crushed aggregates of specified grading, premixed with bituminous binder @ 4.5 to 5 per cent of mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per MoRTH specification clause No. 508 complete in all respects

Providing and laying of hot applied thermoplastic compound 2.5mm thick including rafleat rising glass beads @ 250gms per sqmt area thickness of 2.5mm is exclusive of surface applied glass beads as per IRC-35. The finished surface to be level, uniform and free from streaks and holes etc complete.

Providing and fixing of typical informatory sign board as per MORD specifications and drawing. Three MS Plates of 1.6 mm thick, top and middle plate duly welded with MS flat iron 25mm x 5m size on back on edges. The lower plate will be welded with MS angle iron frame of 25mm x 25mm x 5mm. The angle iron frame of the lower most plate and flat iron frame of middle plate will be welded to 2 nos. 75mm x 75 mm of 12 SWG sheet tubes posts duly embedded in cement concrete M-15 grade blocks of 450mm x 450mm x 600mm, 600mm below ground level. The top most diamond plate will be welded to middle plate by 47mm x 47mm of 12 SWG steel plate tube. All M.S. will be stove enameled on both sides. Lettering and printing arrows, border etc. will be painted with ready mixed synthetic enamel paint of superior quality in required shade and colour. All sections of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per drawing Clause Annexure 300,800, 1700 of MORD as per direction of the Engineer in charge

Providing and erecting direction and place identifications of semi reflective sign boards of size upto 0.90 Sqm. as per IRC 67 made of 2 mm thick MS. Sheet duly stove enameled paint in white colour in front and grey colour on back with red reflective border of 70 mm width and required message, letters, figures with reflective engineering grade tape as per MORD specifications of required shade and colour. Supported and welded on 47 mm x 47mm of 12 SWG Square tube of 3050 mm height duly strerigthened by 25 mm x 5 mm Mis flat iron on edges on back firmly fixed to the ground by means of properly designed foundations with M-15 grade cement concrete 450 mm x 450 mm x 600 mm 600 mm below ground level as per approved drawing and MORD technical Specification Clause 300,800, 1700 as per direction of the Engineer in charge (Inter mediate Board)

Reinforced cement concrete M15 grade kilometre stone of standard design as per IRC 8 fixing in position including painting and printing, etc as per drawing and MORD technical Specification Clause 1703 as per direction of the Engineer in charge

Supplying and fixing 15 cm dia 1.00 m long guard post of RCC M20 using 3.5 kg. of steel for each guard post with 20 mm down graded granite chips including cost of all materials, reinforcement, centering, shuttering and watering etc. complete

R.C.C (M20) using 12mm.size BHGCB chips including all cost complete

Rigid and smooth centering and shuttering for Drain work incl. cost of all materials.

Cutting, straitening, bending,binding of HYSD Bar & tying the grills and placing in position etc.complete incl.cost

Add for Damaged pipe line cost.

Add for other unforeseen item such as wirtting charges of display board etc.