Construction Feeding Room Addl electrical Pumping work chair table carpet window curtain scaffoldings statue for Museum stainless steel drain Entrance panel granite stone Flamed granite stone on entrance Strip Light Dewatering Submersible Pump at KCP

Amount

Wiring with 2 x 1.5 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories in flush with wall with 3mm thick hylum sheet cover with TW switch box and 5A FT switch with continuous earth wire connection of 1.5 sq.mm copper wire for making good of the concealed portion with suitable colour for PVC concealed light point / fan point (for electronic regulator) SD23

Wiring with 2x1.5sqmm (22/0.3) PVC insulated SC unsheathed Cu.Conductor of 1100 V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories, in flush with wall, with 150mm x 100mm x 113mm TW switch box with 3 mm thick Hylem sheet cover for 5 A 3 pin non inter lockingWall socket with 5A Flush type switch with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour for concealed PVC plug point. (SD 38)

Wiring with 2x4 sqmm(56/0.3) PVC insulated SC unsheathed Cu.Conductor cable of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories, in flush with wall, with 150mm x 100mm x 113mm TW switch box with 3mm thick hylem sheet for 15 A 3 pin non inter locking Wall socket with 15A Flush type switch with continuous earth wire connection of 14 SWG TC wire , and making good of the concealed portion, with suitable colour for concealed power plug point (SD 40)

Supply and run of 2 of 1.5 sq.mm(22/0.3) PVC insulated SC unsheathed Cu.Conductor of 1100V grade in suitable heavy gauge MS conduit pipe concealed in wall and ceiling with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour. (SD 43)

Supply and run of 3 of 4 sqmm (56/0.3)PVC insulated SC unsheathed Cu.Conductor of 1100V grade in suitable heavy gauge M.S.conduit pipe on wall and ceiling with continuous earth wire connection of 14 SWG TC wire with painting of suitable colour (SD 46)

Supply and run of 2 of No.8 SWG GI wire for guarding with cradle with No.8 SWG GI wire at the equal interval of 1.5 Metre. (SD 75)

Supply and run of 25mm x 6mm tinned copper flat with necessary clamps / supports on wall / floor / ground for earth connection (SD 77)

Supply and fixing of 4' 40 W single industrial type flu.fitting complete with copper choke and condensor with conduit pipe suspension from the ceiling with PVC unsheathed Copper leads from the terminals to the fitting with flu.tube (SD 92)

Supply and fixing of 1200 mm (48") sweep AC ceiling fan complete with stepped electronic 300W regulator, with 1 metre down rod with fan clamp with side plates and cross arm of size 450 mm (18") (SD 106)

Supply and fixing of 300 mm (12") sweep (light duty) AC exhaust fan complete with necessary wall opening and making good of the wall (SD 114)

Supply and fixing of louvers shutters arrangements for 300 mm (12") sweep (light duty) AC exhaust fan. (SD 120)

Supply and fixing of 5 A 3 Pin and 2 pin combined flush type wall socket with 5A flush type switch concealed in suitable MS box in flush with wall and concealed with 3mm thick hylem sheet (SD 138')

Supply and fixing of 5A / 15 A 3 Pin combined flush type wall socket with 15A flush type switch concealed in suitable MS Box in flush with wall and covered with 3 mm thick hylem sheet (SD 138)

Supply and frxing of brass cable gland for 3 1/2x50 sqmm PVC armoured LTUG cable with earth connection (SD 166)

Same as per SD 175, except for 3-1/2 x 50 sq.mm. PVC armoured LTUG cable(SD-184)

Earthing as per the ISI specification with an earth electrode of 2.1mt class 'B' GI pipe of dia not less than 40mm, with copper earth plate of size 125mm x 50mm x 6mm, with necessary funneling arrangements with necessary masonry work and with 38mm RCC cover slab for the brick masonry (SD 211)

Supply and providing cable end termination of 3 1/2 x 50 sqmm PVC LTUG Aluminium armoured cable with necessary aluminium cable sockets by crimping etc. with electrical connection complete(SD 215)

Supply and fixing of 450mm Sweep WALL MOUNTING FAN . (Make: Usha/ Crompton/Equ.

Supply and fixing of "kalaignar karunanidhi statue"with granite stone piller,complete complying with standard specification and as directed by the departmental officers etc.

Supply and fixing of "entrance panel granite stone size (1.2mx2.4m) with art work,lettering work,complete complying with standard specification and as directed by the departmental officers etc.

Supply and fixing of "stainless steel Drain size (10m lx.10mW) with connecting pipe cutting floor granite inculding cost labour,material,complete complying with standard specification and as directed by the departmental officers etc.

Supply and fixing of "Window Curtain 2 nos for AV Room Fabric,lining,heavy track,stiching,fixing,inculding cost,material,Fabric,lining,heavy track,stiching,fixingcomplete complying with standard specification and as directed by the departmental officers etc.

Supply and fixing of "Window Curtain 6 nos for main hall Fabric,lining,heavy track,stiching,fixing,inculding cost,material,Fabric,lining,heavy track,stiching,fixingcomplete complying with standard specification and as directed by the departmental officers etc.

Supply and fixing of "Window Curtain 2 nos for Vip Room Fabric,lining,heavy track,stiching,fixing,inculding cost,material,Fabric,lining,heavy track,stiching,fixingcomplete complying with standard specification and as directed by the departmental officers etc.

Servo Controlled Voltage Stabilizers: voltage stabilizer is designed for 230V operated equipments, where Voltage fluctuations effects the performance and product life is affected. Typical applications are medical equipments, Xerox copier machines, CNC machines, Printing machines, etcl,complete complying with standard specification and as directed by the departmental officers etc.

For constructing special scaffoldings for use high-strength steel scaffolding systems compliant with IS 2750:1964 standards. Ensure the scaffolding is designed to support the specific load requirements of Steel Purlin and pipe equipment. Equip the structure with adjustable base plates for stability and secure it with diagonal bracing. Install guardrails, toe boards, and access ladders for worker safety, and include non-slip platforms. Regularly inspect the scaffolding for stability and wear, adhering to local safety regulations and manufacturer guidelines. Ensure the scaffolding covers effectively

1 PHASE UPS (Single Phase In & Single Phase Out)CAPACITY - SYSTEM WITH BATTERY - 2 HOURS BACK-UP -5kva

1 PHASE UPS (Single Phase In & Single Phase Out)CAPACITY - SYSTEM WITH BATTERY - 2 HOURS BACK-UP -2kva

1.5 TR Split Type AC Unit - 5 Star Rated

Supply and installation of 4 KVA capacity Automatic Voltage Stabilizer with time delay relay

Supply and laying of "Carpet flooring rosetta new marvel complete complying with standard specification and as directed by the departmental officers etc.

Supply and fixing of MS stand for fixing outdoor unit

Supply and fixing of 4.0 TR 1 Star Commercial Verticool AC Installation, Testing and Commissioning of Verticool UnitSupply, Installation, Testing and Commisioning of Copper Pipe,Supply, Installation, Testing and Commissioning of 1.5 sqmm 4 core Copper cable,Supply, Installation, Testing and Commisioning of Drain Pipe complete complying with standard specification and as directed by the departmental officers etc.

Providing and fixing of Aluminium Composite Panel (ACP) 4 sided having 50 x 25 x 1.50mm frame work vertical and horizontals out of specially designed extruded sections withstand wind pressure of 180 Kg/sq.m and fabricated fixed at all level elevation and heights. The extruded section cutting and fixing required space extruded section shall be of 6063 and alloy of BSH 9 confirming T is – 63400 rate shall included to fix the main frame with necessary clamps, fasteners, bolt nuts etc. The main frame of extruded section shall be of 22843 & 22739 (H9) grade conforming to BS 4174 (or) IS 8147. Rate shall included 4mm thick ACP sheet (0.25 + 3.5 + 0.25) alstrong or equivalent fixing with spacer tape and the ACP sheet bounded with special type structural sealant of dow corning 789 or equivalent in dust free conditions the gaps between ACP sheet to be filed with whether sealant and backer rod or 12mm foam sheet to ensure water and air tightness in all complete complying with standard specification as directed by the departmental officer

Providing and fixing ply wood 12mm with pvc1mm thick floor level complete complying with standard specification and as directed by the departmental officers etc.

Supply and fixing of flammed granite stone of 40 mm thick including transporation ,labour charges for laying and levelling with necessary mortar and fixing, curing, and finishing neatly etc., complete complying and as directed by the departmental officers

24W LED 4000K 2 x 2 Square Type Recessed Fitting with LED

18W LED 3000K Round Type Recessed Fitting with LED

Supply of Computer table including transporation etc., complete complying and as directed by the departmental officers

Hydraulic Door Closer of various sizes of approved quality using Aluminium Extruded Section Body Tubular Type Universal Hydraulic Door Closer with Double Speed Adjustment like HARDWYN (make) ‘GAZEL’ (or) Equivalent (with ISI Monogram)

fixing in position Name Granite rock stone , complete complying and as directed by the departmental officers.

Providing and laying, spreading and compacting graded stone aggregates to Wet Mix Macadam 250 mm thick specification including premixing the materials with water at OMC in mechnanical mix plant carriage of mixed material by tipper to site laying in uniform layers with pavers in Sub Base/ Base course on well prepared surface and compacting with vibratory roller to acheive the desired density including cost of material, labour charges, rentals for machinery, fuel and all other incidental charges etc., complete as per clause 406 of MORTH Rev-5

Supply and fixing of LED Spot Light 7/9W, complete complying and as directed by the departmental officers.

Supply and Laying of Homogeneous Dot free LED Flexible strip Light with high quality circuit design for stable and reliable performance, surface material should be made of Silicon with aluminium extrusion linear profile and other connecting accessories, Surface mounted flexible linear light suitable for facade edge lighting, Symmetric distribution. luminaire should have diffuse silicone based cover for soft illumination. Linear luminaire should have lumen flux in range of 900- 1000 lm per meter, Rated input supply of DC 24V constant voltage with external LED Driver, . Luminaire body of aluminium extrusion with aluminium components. With flush-fitting cover and integral LED unit. Colour of luminaire body Grey/Silver, highly weather resistant/ powder-coated. Ingress protection rating (DIN EN 60529): IP68, impact resistance level should be suitable to site condition. The LED system with control gear unit is suitable for operation on direct voltage supply grids. The luminaire should be provided with Electrical safety class I. With aluminium channel and diffuser IP66. etc., complete.

Supply and Laying of Homogeneous Dot free LED Flexible strip Light with high quality circuit design for stable and reliable performance, other connecting accessories, Surface mounted flexible Strip light suitable for facade edge lighting, Symmetric distribution. luminaire should have lumen flux in range of 900- 1000 lm per meter, Rated input supply of DC 24V constant voltage with external LED Driver, With flush-fitting cover and integral LED unit . Ingress protection rating (DIN EN 60529): IP68, impact resistance level should be suitable to site condition. The LED system with control gear unit is suitable for operation on direct voltage supply grids. The luminaire should be provided with Electrical safety class I and diffuser IP66. etc., complete.

450mm Pedestal air circulator fan

Supplying and laying of Galvolume sheet 0.5 mm thick of approved quality for roofing with necessary U or J bolts and unts bitumen GI washers etc., complete complying with standard specification.

Fabricating and supplying and erecting the required number of trusses with structural steel members like angle iron MS plates for all truss members including cleats to receive the purlines all cutting drilling holes welding and fixing of members with necessary bolts nuts anchor bolt of approved quality hoisitn aligning and glazing the trusses inposition as per plan. The rate should include the cost painting the members with one coat of red oxide primer and zinc chromate etc., complete complying with standard specification and an directed bya the departmental officers.

Supplying and fixing in position PARRYWARE One Piece Floor Mounted Western Commode, 12 litter capacity low level flushing tank including all internal fittings on CI brackets, 12mm brass nipple, chromium plated brown headed stop cock, 12mm nylon connection connecting with walls and floors including dismantling masonry and redoing the same to the original condition etc., complete complying with standard specification and as directed by the Departmental officers.

Supplying and fixing in position best quality approved make white glazed earthenware PARRYWARE wash hand basin of pair of cast iron brackets, including cost of 15mm dia metre brass chromium plated pillar tap, 32mm dia metre G. M. Wheel valve, 15mm dia brass nipple 15mm dia nylon connection etc. including fixing the wash hand basin in the wall in position with pair of CI brackets with teak wood plugs and screws and giving necessary water supply connection and painting the brackets with two coats of paint over a priming coat of anticorrosive paint including testing for leakage etc. complete complying with standard specification. The quality and colour of wash hand basin and specials should be got approved by the Executive Engineer before use on work.

SS Long body Tap

CP two way Blb cock with health faucet

Supplying and fixing in Position Indian make bevelled edge mirror of approved quality and brand PVC/Fibre Glass framed 600x450x5.5mm thick mirror, shelf type with hard board backing of approved colour fixed with brass screws, rawl plug, etc., complete complying with standard specification. (The mirror should be got approved by the Executive Engineer before use on works)

Swan Neck Tap

Parryware Standard Towel Ring (dia 7”) , Silver, Alloy Steel

Manufacturing, Supplying and Fixing of Stainless Steel Hand rails for staircase using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick at required locations to a height of 900mm from finished floor level welded to 38mm dia Stainless Steel pipe post of 1.00mm thick as vertical at 900mm centre with 2 Nos. of 25mm dia intermediate horizontal stainless steel pipe of 1.60mm thick in between. The vertical pipe has to be welded to the 100 X 100 X 6mm MS base plate encased in the base concrete. The rate is inclusive of the charges for cutting, bending, welding, grinding, polishing, conveyance, electrical charges, etc. complete

KSB MAKE DEWATERING SUBMERSIBLE PUMP 3HP,3PHASE,MODEL:MONOSUB-RMR(S)-20X

2 Core - 2.5 sq.mm

KSB MAKE DEWATERING SUBMERSIBLE PUMP 1HP,SINGLE PHASE,MODEL:KSTP10

KHYATEE MAKE DOL PANEL BOARD

2" PVC LAY HOSE

HOSE CLIPS

Supplying of PVC chair .,complete complying with standard specification and as directed by the departmental officers etc.

Granite Floor Finish work,complete complying with standard specification and as directed by the departmental officers etc.

Earthwork excavation for foundation (for narrow excavation) to full depth as per designed in all soils and sub soils except soft disintegrated rock not requiring blasting and hard rock requiring blasting and bailing water wherever necessary. Refilling the sides of foundation with excavated earth other than sand in layers of well rammed and compacted and depositing the surplus earth in places shown by the departmental officers with an initial lead of 10m and initial lift of 2m and clearing and leveling the site etc. complete

Supplying and filling of gravel for basement in layers of not more than 15cm thick well watered, rammed and consolidated etc., complete as per standard specification.

Plain Cement concrete 1:4:8 (One cement four M sand and eight broken Machine crushed stone jelly) using HBG Machine crushed stone jelly of size 40mm gauge for founding and basement including de- watering if found necessary and laid in layers of not more than 15cms thick etc., complete complying with standard specification and as directed by the departmental officers.

Reinforcement Cement Concrete 1:2:4 (One Cement two sand four aggregate) using machine crushed 20mm gauge HBS jelly for all RCC works with Pidilite oil connected to this work excluding grill placed in position but including consolidating by mixing for machine vibraters and finishing etc., complete .

Supplying and erecting centering for sides and soffits including necessary supports and strutting up to 3.29 M height for plane surfaces as detailed below in all floors with all cross bracings using Mild Steel sheets of size 90 x 60 cm and 10 BG stiffened with welded Mild Steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at about 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete

For column footing, Column pedestals, plinth beam, grade beams, staircase stpes, etc.,

Painting new iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with two coats of best approved first quality and colour of synthetic enamel paint over the existing red oxide priming coat in all floors including cost of priming coat etc., complete complying with standard specification. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)

Fabricating and supplying and erecting the required number of trusses with structural steel members like angle iron MS plates for all truss members including cleats to receive the purlines all cutting drilling holes welding and fixing of members with necessary bolts nuts anchor bolt of approved quality hoisitn aligning and glazing the trusses inposition as per plan. The rate should include the cost painting the members with one coat of red oxide primer and zinc chromate etc., complete complying with standard specification and an directed bya the departmental officers.

Supplying and laying of " Ramco" brand "Greencor" Non Asbestos Cement Sevencor Fully-Corrugated Roofing Sheets 6mm thick, 1.05 M width as per IS 14871 2000 (HSN : 6811 8100 )of approved quality for roofing with necessary U or J bolts and unts bitumen GI washers etc., complete complying with standard specification.

Supplying, fabricating, erecting and fixing Gyp Board false ceiling upto a ceiling height of 4.50m from floor level with plain gyp boards of 10mm thick and GI metal channel of size 45 X 15 X 0.9mm forming a grid of 120 X 60cm and anchored to the celing with dash fasteners of 12.50mm dia, 40mm long 6mm dia bolt and nut to the hanger of 25x25x5mm of required length. The other end of the angle fixed with bolt and nut to GI channel. The GI frame work will be covered with 10mm thick gyp board of approved quality confirming to IS 2095.

Supplying and fixing of Cornice in the false roof ceiling etc., complete.as directed by the Departmental officers

8 Providing and fixing of Aluminium Composite Panel (ACP) 4 sided having 50 x 25 x 1.50mm frame work vertical and horizontals out of specially designed extruded sections withstand wind pressure of 180 Kg/sq.m and fabricated fixed at all level elevation and heights. The extruded section cutting and fixing required space extruded section shall be of 6063 and alloy of BSH 9 confirming T is – 63400 rate shall included to fix the main frame with necessary clamps, fasteners, bolt nuts etc. The main frame of extruded section shall be of 22843 & 22739 (H9) grade conforming to BS 4174 (or) IS 8147. Rate shall included 4mm thick ACP sheet (0.25 + 3.5 + 0.25) alstrong or equivalent fixing with spacer tape and the ACP sheet bounded with special type structural sealant of dow corning 789 or equivalent in dust free conditions the gaps between ACP sheet to be filed with whether sealant and backer rod or 12mm foam sheet to ensure water and air tightness in all complete complying with standard specification as directed by the departmental officer

Providing UPVC (Un-Plasticized Polyvinyl Chloride) Door: Providing and fixing casement doors fabricated from un plasticized polyvinyl chloride (uPVC) sections. Profiles: The profiles should be three chamber system which provides high insulation properties with outer frame 60mm x 55mm with an outer wall thickness of 2.4mm. The window unit should be designed with all corner joints mitred and fusion welded. Windows should be steel reinforced with 25 x 24 x 25mm steel reinforcement with a thickness of 1mm to have dimensional stability. The sash should be of 60 x 102mm. The mullion should be of 60 x 74mm. The profiles should have co-extruded seals. Hardware: All the hardware like friction stays, handles should be screwed with self tapping screws. The handles, locks should be designed so that they cannot be released from outside. Glazing: The window system should be glazed with 5mm plain float glass / 6mm bison lam Installation: The profiles should be cut to length and welded 45 degrees. The window should be designed such that the water drainage does not pass through the reinforcement chamber. The window system should be fixed directly to the plastered brick wall using self expanding nylon plug and driving ms electroplated screws into plug.

Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Louvered Ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 x 78mm both profiles are reinforced with GI/1mm 125GSM and 100% corrosion free, the profile are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with all over the edges of frame and shutter. The corners and joints should be welded and cleaned. Radiations pin headed glass 4mm thick should be provided in the louvers. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The ventilator should be got approved from the Executive Engineer before use on work

Supplying and fixing of Vinyl flooring for Feeding Room. The rate including the cost of all material, Transportation. Loading, unloading, Labour charges for fixing and neat finishing etc., complete.

GST at 18 percentage

SRE MCM & CO (BID ID -1219058)

PHOENIX & CO (BID ID -1219556)