Construction of vertical Extension for an additional floor over the existing buildings of Hostel No. 7, 8 and 9 at NIT Kurukshetra

Providing and laying in position cement concrete of specified grade excluding the

1 4.1 cost of centering and shuttering - All work up to plinth level :

1:2:4 (1 cement : 2 coarse sand) derived from natural sources : 4 raded stone

1.1 4.1.3 aggregate 20 mm nominal size derived from natural sources) cum 104.55474 ₹ 7,665.78 ₹ 8,01,493.63

II 5.0 REINFORCED CEMENT CONCRETE

Centering and shuttering including strutting, propping etc. and removal of form

Walls (any thickness) including attached pilasters, butteresses, plinth and string

2.2 5.9.3 Suspended floors, roofs, landings, balconies and access platform sqm 5727.177 ₹ 902.21 ₹ 51,67,116.36

2.4index @4% on DSR 2023 (Civil)

beams, plinth beams, girders, bressumers and cantilevers sqm 7693.7058 ₹ 716.52 ₹ 55,12,694.08

2.5index @1% on DSR 2025 (E & M) items

Columns, Pillars, Piers, Abutments, Posts and Struts sqm 4963.32 ₹ 935.34 ₹ 46,42,391.73

2.6 5.9.7 Stairs, (excluding landings) except spiral-staircases sqm 260.61372 ₹ 744.30 ₹ 1,93,974.79

2.7 5.9.16 Edges of slabs and breaks in floors and walls

2.8 5.9.19 Weather shade, Chajjas, corbels etc., including edges sqm 195.84 ₹ 925.42 ₹ 1,81,234.25

Steel reinforcement for R.C.C. work including straightening, cutting, bending,

2.9 5.22A placing in position and binding all complete above plinth level.

2.9.1 5.22A.6 Thermo-Mechanically Treated bars of grade Fe-500D or more. kg 303705.31 ₹ 104.94 ₹ 3,18,70,835.26

Add for plaster drip course/ groove in plastered surface or moulding to R.C.C.

Providing and laying in position ready mixed or site batched design mix cement

concrete for reinforced cement concrete work; using coarse aggregate and fine

aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland

/Portland Slag cement, admixtures in recommended proportions as per IS: 9103

to accelerate / retard setting of concrete, to improve durability and workability

without impairing strength; including pumping of concrete to site of laying,

curing, carriage for all leads; but excluding the cost of centering, shuttering,

finishing and reinforcement as per direction of the engineer-in-charge; for the

following grades of concrete.

Note: Extra cement up to 10% of the minimum specified cement content

in design mix shall be payable separately. In case the cement content in

design mix is more than 110% of the specified minimum cement

content, the contractor shall have discretion to either re-design the mix

or bear the cost of extra cement.

2.11.1 5.33.2 All works above plinth level upto floor V level

2.11.1.1 5.33.2.1 Concrete of M25 grade with minimum cement content of 330 kg /cum cum 2336.1947 ₹ 9,594.17 ₹ 2,24,13,849.05

Providing and fixing parallel threaded couplers conforming to IS code on

"Reinforcement Couplers for Mechanical Splices of Bars for Concrete

2.12 5.42 Reinforcement- Specification . to reinforcement bars including threading,

enlargement at connection by forging, protecting the prepared reinforcement

bars and related operations as required to complete the works per direction of

Engineer- in-Charge.

2.12.1 5.42.1 Coupler for 16 mm diameter reinforcement bar each 2400 ₹ 111.99 ₹ 2,68,776.00

2.12.2 5.42.2 Coupler for 20 mm diameter reinforcement bar each 1800 ₹ 155.78 ₹ 2,80,404.00

2.12.3 5.42.3 Coupler for 25 mm diameter reinforcement bar each 900 ₹ 222.77 ₹ 2,00,493.00

2.12.4 5.42.5 Coupler for 32 mm diameter reinforcement bar each 300 ₹ 310.19 ₹ 93,057.00

Floor Joint 100mm Providing & Fixing of Expansion Joint system related with the

Floor to Floor/ Floor to Wall Expansion Joint Cover for 100 mm Expansion Joints

Aluminium Covers Profiles, having a Hard Wearing, Maintenance Free, long

Lasting design. The surface of the Exp. Joint Covers should have Serrated

Surface for Skid Resistance and should be ADA Compliant. The exposed surface

should not exceed 113mm.The design of the Exp. Joint Cover System should be

such that it should avoid any accumulation of dirt. The Exp. Joint Cover should

have an Articulated Telescope Design so as to accommodate the movements in

2.13 5.44 3 directions. The system should be in alloy 6063 T66 in Mill finish and the total

exposed surface of the profile should not be more than 113 & the installation

Height can be of 35 mm. The system can be used for standard Rolling loads of

private Cars or Cart wheel loads. The system should have ASTM1399 E

certification. The extrusion should be as ASTM 6063 T66 standards. The System

shall be such that it will be flushed with the finish The System should be ASTM-E

1399. Provision of Moiser Barrier in the Joint System to have watertight joint is

mandatory requirement all as per the manufactures design and as approved by

the Engineer-in-Charge.

Providing & Fixing of Expansion Joint system related with the WALL to WALL

(Internal / External) Location as per drawing and direction of engineer –In-

Charge. Expansion Joint The design of the Joint Cover System should be such

that the system should snap onto a 50mm wide, hook shaped aluminum clip.

The system should have gasket seals on the edges to provide scratch protection

2.15 5.45 to the wall finish and prevent accumulation of dust. The system should be in

6063 alloy in clear anodized matt finish. Provision of Moisture Barrier Membrane

in the Joint System to have watertight joint is mandatory requirement for all

external area as per the manufactures design and as approved by the Engineer-

Digitally signed by SUJEET

Sl.No. CIVIL AND 2025 Description Unit Qty DSR Amount Non-DSR Amount

Providing and fixing of expansion joint system of approved make and

Manufactures for various roof locations as per approved drawings and Direction

of Engineer-In-Charge. The joints shall be of extruded aluminium base

members with, self aligning and self centring arrangement support plates as per

ASTM B221-02. The system shall be such that it provides watertight roof to

roof/roof to corner joint cover expansion control system that is capable of

accommodating multidirectional seismic movement without stress to its

components. System shall consist of metal profile that incorporates a universal

aluminium base member designed to Accommodate various project conditions

and roof treatments. The cover plate shall be designed of width and thickness

2.16 5.46 required to satisfy movement and loading requirements and secured to base

members by utilizing manufacturer’s pre-engineered self-centring arrangement

that freely rotates / moves in all directions. The Self centring arrangement shall

exhibit circular sphere ends that lock and slide inside the corresponding

aluminium extrusion cavity to allow freedom of movement and flexure in all

directions including vertical displacement. The Joint System shall resists damage

or deterioration from the impact of falling ice, exposure to UV, airborne

contaminants and occasional

foot traffic from maintenance personnel. Provision of Moisture Barrier Membrane

in the Joint System to have water tight joint is mandatory requirement.

(Material shall confirm to ASTM 6063

III 6.0 MASONRY WORK

Brick work with common burnt clay F.P.S. (non modular) bricks of class

3 6.4 designation 7.5 in superstructure above plinth level up to floor V level in all

shapes and sizes in:

3.1 6.4.2 Cement mortar 1:6 (1 cement :6 coarse sand) cum 994.1204 ₹ 8,860.09 ₹ 88,07,996.20

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class

3.2 6.13 designation 7.5 in superstructure above plinth level up to floor Vlevel.

3.2.1 6.13.2 Cement mortar 1:4 (1 cement :4 coarse sand) sqm 3791.363 ₹ 1,093.46 ₹ 41,45,703.83

Extra for providing and placing in position 2 Nos 6 mm dia. M.S. bars at every

third course of half brick masonry.

IV 8.0 CLADDING WORK

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and

prepolished, machine cut for kitchen platforms, vanity counters, window sills,

facias and similar locations of required size, approved shade, colour and texture

4.1 8.2 laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand),

joints treated with white cement, mixed with matching pigment, epoxy touch

ups, including rubbing, curing, moulding and polishing to edges to give high

gloss finish etc. complete at all levels.

4.1.1 8.2.2 Granite stone slab colour black, Cherry/Ruby red

Providing edge moulding to 18 mm thick marble stone counters, Vanities etc.,

4.2 8.3 including machine polishing to edge to give high gloss finish etc. complete as

per design approved by Engineer-in-Charge.

Extra for fixing marble /granite stone, over and above corresponding basic item,

4.3 8.4 in facia and drops of width upto 150 mm with epoxy resin based adhesive, metre 301.2 ₹ 553.20 ₹ 1,66,623.84

including cleaning etc. complete.

Extra for providing opening of required size & shape for wash basin/ kitchen sink

in kitchen platform, vanity counter and similar location in marble/ Granite/ stone

4.4 8.5 work, including necessary holes for pillar taps etc. including moulding, rubbing each 36 ₹ 952.28 ₹ 34,282.08

and polishing of cut edges etc. complete.

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622

(thickness to be specified by the manufacturer), of approved make, in all

colours, shades except burgundy, bottle green, black of any size as approved by

4.5 8.31 Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed sqm 403.65 ₹ 1,233.72 ₹ 4,97,991.08

of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement

slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment

of matching shade complete.

Stone tile work for wall lining upto 10 m height with special adhesive over 12

4.6 7.38 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand), including

pointing in white cement with an admixture of pigment to match the stone

4.6.1 7.38.1 8 mm thick (mirror polished and machine cut edge)

4.6.1.1 7.38.1.1 Granite stone of any colour and shade sqm 21.21825 ₹ 3,011.00 ₹ 63,888.15

V 9.0 WOOD AND P. V. C. WORK

Providing and fixing factory made single extruded WPC (Wood Polymer

Composite) solid door/window/Clerestory windows & other Frames/ Chowkhat

comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium

carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non

toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter

joints after applying PVC solvent cement and screwed with full body threaded

star headed SS screws having minimum frame density of 750 kg/cum, screw

5.1 26.86 withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive

strength of 58 N/mm2, modulus of elasticity 900 N/mm2 and resistance to

spread of flame of Class A category with property of being termite/borer proof,

proof and fire retardant and fixed in position with M.S hold fast/lugs/SS dash

fasteners of required dia and length complete as per direction of Engineer-In-

Charge. (M.S hold fast/lugs or SS dash fasteners shall be paid for separately).

Providing and fixing ISi marked flush door shutters conforming to IS : 2202

(Part I) non-decorative type, core of block board construction with frame of 1st

5.2 9.21 class hard wood and well matched commercial 3 ply veneering with vertical

grains or cross bands and face veneers on both faces of shutters:

35 mm thick including ISi marked Stainless Steel butt hinges with necessary

Extra for providing lipping with 2nd class teak wood battens 25 mm minimum

5.3 9.23 depth on all edges of flush door shutters (over all area of door shutter to be sqm 849.69 ₹ 449.87 ₹ 3,82,250.04

Extra for providing vision panel not exceeding 0.1 sqm in all type of flush doors

5.4 9.24 (cost of glass excluded) (overall area of door shutter to be measured):

Digitally signed by SUJEET

Sl.No. CIVIL AND 2025 Description Unit Qty DSR Amount Non-DSR Amount

5.4.1 9.24.1 Rectangular or square sqm 25.92 ₹ 193.77 ₹ 5,022.52

Extra for cutting rebate in flush door shutters (Total area of the shutter to be

Providing & Fixing decorative high pressure laminated sheet of plain / wood

5.6 9.127 grain in gloss / matt/ suede finish with high density protective surface layer and

reverse side of adhesive bonding quality conforming to IS : 2046 Type S,

including cost of adhesive of approved quality.

Supply & Fixing rack and pinion door closer EN size 2/3/4, with std. arm and

5.7 MR with two independent closing valves and latching speed adjustable by arm. each 369 ₹ 3,510.00 ₹ 12,95,190.00

Silver finish. As per EN 1154. as per direction of engineer-in-charge

Supply & Fixing Type 1 Lever Handle Package with Antiviral / Antimicrobial

coated Lever Handle - clear & transparent coating with protection tested for

antibacterial activity with up to 99.9% effectiveness* as per ISO 22196 and

5.8 MR antiviral activity with 99.9% reduction as per ISO 21702. Pair Lever Handle on each 369 ₹ 11,371.00 ₹ 41,95,899.00

Roses & escutcheons. Including Sash lock with 72mm CTC, 55mm Backset

20mm Square forend. EPC 60mm length both side key operation . as per

direction of engineer-in-charge

Supply & Fixing floor stop half dome with 45mm dia with fixing accessories, in

satin Chrome. as per direction of engineer-in-charge

SPECIFICATION FOR 125X60MM (DOUBLE REBATE) DOOR FRAMES

Providing and Fixing double rebate door frame fabricated from sections roll

formed out of 1.2mm thick galvanized steel (Base steel as per IS 513) with zinc

of 120 gms/sq.mtr. The overall size of the section should be 125x60mm.

The frame section should be cut to length and meter joined with corner brackets

made of CRCA electroplated.

The frame should be provided with .

(a) 3 Nos. of M.S. powder coated 4” Butt hinges of 2mm thickness welded to the

(b) 6 Nos. of 1.2mm thick CRCA electroplated stiffeners should be welded to

(c) 6 Nos. of 8” M.S. hold fasts with split end tail welded to stiffener plates

(d) One no. aldrop receiver.

(e) Each frame should be provided with 25x50mm tie rod at bottom.

All welded places should be treated with protective coat of zinc rich primer.

The entire frame should be provided with a coat of etch primer.

(Make: Elixir Met Form Pvt Ltd. / A2Z Infra Solutions / AKG Infracon)

VI 10.0 STEEL WORK

Steel work welded in built up sections/ framed work, including cutting, hoisting,

6.1 10.25 fixing in position and applying a priming coat of approved steel primer using

structural steel etc. as required.

In gratings, frames, guard bar, ladder, railings, brackets, gates and similar

VII 11.0 FLOORING WORK

Marble stone flooring with 18 mm thick marble stone, as per sample of marble

7.1 11.23 approved by Engineer-in-charge, over 20 mm (average) thick base of cement

mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with grey cement slurry,

including rubbing and polishing complete with:

7.2 11.24 Extra for pre finished nosing to treads of steps of marble stone. metre 630 ₹ 700.46 ₹ 4,41,289.80

Extra for marble stone flooring in treads of steps and risers using single length

up to 2.00 metre.

Kata stone slab flooring over 20 mm (average) thick base laid over and jointed

7.4 11.26 with grey cement slurry mixed with pigment to match the shade of the slab,

including rubbing and polishing complete with base of cement mortar 1 :4 (1

cement: 4 coarse sand):

Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on

12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and

7.5 11.27 jointed with grey cement slurry mixed with pigment to match the shade of the sqm 1547.4 ₹ 2,291.12 ₹ 35,45,279.09

slabs, including rubbing and polishing complete.

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to

be specified by the manufacturer) of 1st quality conforming to IS : 15622 of

approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on

7.6 11.37 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey sqm 63.75 ₹ 1,066.94 ₹ 68,017.43

cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and

matching pigment etc., complete.

Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or

more (thickness to be specified by the manufacturer), of 1st quality conforming

to IS : 15622, of approved make, in colours White, Ivory, Grey, Fume Red

7.7 11.39 Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement: 4 Coarse sand), sqm 630.036 ₹ 1,294.09 ₹ 8,15,323.29

jointing with grey cement slurry@ 3.3 kg/ sqm including grouting the joints with

white cement and matching pigments etc., complete.

Providing and laying double charge vitrified floor tiles in different sizes

(thickness to be specified by the manufacturer) with water absorption less than

0.08% and conforming to IS: 15622, of approved make, in all colours and

7.8 11.41A shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand),

jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints

with white cement and matching pigments etc., complete.

7.8.1 11.41A.1 Double charge vitrified tile polished finish of size

7.8.2 11.41A.3 Glazed Vitrified tiles Matt/Antiskid finish of size

Providing and laying Vitrified tiles in different sizes (thickness to be specified by

manufacturer), with water absorption less than 0.08 % and conforming to LS.

15622, of approved make, in all colours & shade, in skirting, riser of steps, over

7.9 11.46 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with

grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white

cement & matching pigments etc. complete.

Digitally signed by SUJEET

Sl.No. CIVIL AND 2025 Description Unit Qty DSR Amount Non-DSR Amount

Providing and laying matt finished vitrified tile of size 300x300x9.8 mm having

with water absorption less than 0.5% and conforming to IS: 15622 of approved

make in all colours and shades in for outdoor floors such as footpath, court yard,

7.10 16.89 multi modals location etc., laid on 20 mm thick base of cement mortar 1:4 (1 sqm 157.005 ₹ 1,416.35 ₹ 2,22,374.03

cement : 4 coarse sand) in all shapes & patterns including grouting the joints

with white cement mixed with matching pigments etc. complete as per direction

of Engineer-in-Charge.

VIII 12.0 ROOFING WORK

Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand :

8.1 12.21 4 stone aggregate 10 mm and down gauge), including finishing with cement

mortar 1:3 (1 cement : 3 fine sand) as per standard design :

Providing and fixing Heat Resistant Terrace Tiles (300 mm x 300 mm x 20 mm)

with SRI (solar refractive index) > 78, solar reflection > 0.70 and initial

emittance > 0.75 on waterproof and sloped surface of terrace, laid on 20 mm

thick cement sand mortar in the ratio of 1:4 (1 cement : 4 coarse sand) and

8 12.55 grouting the joints with mix of white cement & marble powder in ratio of 1:1, sqm 6350.3776 ₹ 1,657.94 ₹ 1,05,28,544.97

including rubbing and polishing of the surface upto 3 cuts complete, including

providing skirting upto 150 mm height along the parapet walls in the same

IX 13.0 FINISHING WORK

9.1 13.4 12 mm cement plaster of mix :

9.2 13.6 20 mm cement plaster of mix :

9.3 13.16 6 mm cement plaster of mix :

Extra for plastering exterior walls of height more than 10 m from ground level

for every additional height of 3 m or part thereof.

Providing and applying white cement based putty of average thickness 1 mm, of

9.5 13.80 approved brand and manufacturer, over the plastered wall surface to prepare sqm 85997.875 ₹ 151.84 ₹ 1,30,57,917.32

the surface even and smooth complete.

9.6 13.50 Applying priming coat:

With ready mixed aluminium primer of approved brand and manufacture on

resinous wood and plywood

Painting with synthetic enamel paint of approved brand and manufacture to give

an even shade :

9.7.1 13.62.1 Two or more coats on new work sqm 149.82075 ₹ 220.14 ₹ 32,981.54

9.8 13.45 Finishing walls with textured exterior paint of required shade :

New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including

priming coat of exterior primer applied @ 2.20kg/10 sqm

Wall painting with premium acrylic emulsion paint of interior grade, having VOC

9.9 13.83 (Volatile Organic Compound ) content less than 50 grams/ litre of approved

brand and manufacture, including applying additional coats wherever required to

achieve even shade and colour.

Distempering with 1st quality acrylic distemper (ready mixed) having VOC

9.10 13.41 content less than 50 gram/litre, of approved manufacturer and of required shade

and colour all complete to achieve even shade and colour :

New work (two or more coats) over and including water thinnable priming coat

9.10.1 13.41.1 with cement primer having VOC content less than 50 gram/litre sqm 773.784 ₹ 180.64 ₹ 1,39,776.34

X 21.0 ALUMINIUM WORK

Providing and fixing aluminium work for doors, windows, ventilators and

partitions with extruded built up standard tubular sections/ appropriate Z

sections and other sections of approved make conforming to IS: 733 and IS:

1285, fixing with dash fasteners of required dia and size, including necessary

filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM

10.1 21.1 rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free,

straight, mitred and jointed mechanically wherever required including cleat

angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless

steel screws, all complete as per architectural drawings and the directions of

Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for

10.1.1 21.1.1 For fixed portion

Anodised aluminium (anodised transparent or dyed to required shade according

to IS: 1868, Minimum anodic coating of grade AC 15)

For shutters of doors, windows & ventilators including providing and fixing

10.2 21.1.2 hinges/ pivots and making provision for fixing of fittings wherever required

including the cost of EPDM rubber / neoprene gasket required (Fittings shall be

paid for separately)

Anodised aluminium (anodised transparent or dyed to required shade according

to IS: 1868, Minimum anodic coating of grade AC 15)

Providing and fixing glazing in aluminium door, window, ventilator shutters and

partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the

10.3 21.3 architectural drawings and the directions of engineer-in-charge .

(Cost of aluminium snap beading shall be paid in basic item):

With float glass panes of 8 mm thickness (weight not less than 20 kg/sqm)

Providing and fixing double action hydraulic floor spring of approved brand and

manufacture conforming to IS : 6315, having brand logo embossed on the body

/ plate with double spring mechanism and door weight upto 125 kg, for doors,

10.4 21.4 including cost of cutting floors, embedding in floors as required and making good

the same matching to the existing floor finishing and cover plates with brass

pivot and single piece M.S. sheet outer box with slide plate etc. complete as per

the direction of Engineerin- charge.

10.4.1 21.4.1 With stainless steel cover plate minimum 1.25 mm thickness Each 264 ₹ 2,747.61 ₹ 7,25,369.04

Providing and fixing aluminium tubular handle bar 32 mm outer dia, 3.0 mm

10.5 21.12 thick & 2100 mm long with SS screws etc .complete as per direction of Engineer-

Powder coated minimum thickness 50 micron aluminium tubular handle bar

Providing and fixing 12 mm thick frameless toughened glass door shutter of

approved brand and manufacture, including providing and fixing top & bottom

10.6 21.18 pivot & double acting hydraulic floor spring type fixing arrangement and making Sqm 926.64 ₹ 5,182.10 ₹ 48,01,941.14

necessary holes etc. for fixing required door fittings, all complete as per

direction of Engineer-in-charge (Door handle, lock and stopper etc.to be paid

Digitally signed by SUJEET

Sl.No. CIVIL AND 2025 Description Unit Qty DSR Amount Non-DSR Amount

Filling the gap in between aluminium/ stone/ wood frame and adjacent

RCC/Brick/ Stone/ wood/ Ceramic/ Gypsum work by providing weather/

10.7 21.19 structural non sag elastomeric PU sealant over backer rod of approved quality as

per architectural drawings and direction of Engineer-in-charge complete,

complying to ASTM C920, DIN 18540-F & ISO 11600

XI 22.0 WATER PROOFING WORK

Providing and laying water proofing treatment to vertical and horizontal surfaces

of depressed portions of W.C., kitchen and the like consisting of:

(i) Ist course of applying cement slurry @ 4.4 kg/sqm mixed with water proofing

compound conforming to IS : 2645 in recommended proportions including

rounding off junction of vertical and horizontal surface.

(ii) IInd course of 20 mm cement plaster 1:3 (1 cement : 3 coarse sand) mixed

with water proofing compound in recommended proportion including rounding

off junction of vertical and horizontal surface.

(iii) IIIrd course of applying blown or residual bitumen applied hot at 1.7 kg. per

(iv) IVth course of 400 micron thick PVC sheet. (Overlaps at joints of PVC sheet

should be 100 mm wide and pasted to each other with bitumen @ 1.7 kg/sqm).

Providing and laying integral cement based water proofing treatment including

preparation of surface as required for treatment of roofs, balconies, terraces etc

consisting of following operations:

11.2 22.7 (a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed

with water proofing compound conforming to IS. 2645 and approved by

Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm

height including cleaning the surface before treatment.

(b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115

mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed

with water proofing compound conforming to IS : 2645 and approved by

Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1

cement :5 coarse sand) admixed with water proofing compound conforming to

IS : 2645 and approved by Engineer-in-charge to required slope and treating

similarly the adjoining walls upto 300 mm height including rounding of junctions

of walls and slabs.

(c) After two days of proper curing applying a second coat of cement slurry

using 2.75 kg/ sqm of cement admixed with water proofing compound

conforming to IS : 2645 and approved by Engineer-in-charge.

(d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4

(1 cement :4 coarse sand) admixed with water proofing compoundconforming to

IS : 2645 and approved by Engineer-in-charge including laying glass fibre cloth

of approved quality in top layer of plaster and finally finishing the surface with

trowel with neat cement slurry and making pattern of 300x300 mm square 3

(e) The whole terrace so finished shall be flooded with water for a minimum

period of two weeks for curing and for final test. “All above operations to be

done in order and as directed and specified by the Engineer-in-Charge”:

With average thickness of 120 mm and minimum thickness at khurra as 65 mm.

XII MISCELLANEOUS WORK

Providing and laying foam concrete under sunken portion of floors as per indian

12.1 MR standard code - IS 2185 with dry density upto 600 kg per cum including Cum 94.644 ₹ 7,960.00 ₹ 7,53,366.24

ramming and consolidation, all complete as per the direction of Engineer-in-

Total DSR Amount ₹ 21,39,64,153.00

Total Non DSR Amount ₹ 88,59,653.00

DSR AMOUNT Non DSR AMOUNT

GROSS TOTAL CIVIL WORK ₹ 22,28,23,806.00

Digitally signed by SUJEET

Construction of Vertical extension for an additional floor over the existing buildings of Hostel No. 7, 8 & 9 at NIT Kurukshetra.

(Plumbing Works)

SOR/DS DSR RATE

DESCRIPTION UNIT QTY DSR Amount NON DSR Amount

NO 2023/M correction

Providing and fixing water closet squatting pan ( Indian type W.C. pan )

with 100mm sand cast Iron P or S trap, 10 litre low level white P.V.C.

flushing cistern with manually controlled device (handle lever) conforming

to IS:7231, Parryware/Hindware/Seabird/Orient (Coral) with all fittings

and fixtures complete including cutting and making good the walls and

floors wherever required.

White Vitreous china Orissa pattern W.C. pan of size 580x440mm with

integral type foot rests

Providing and fixing white viterious china pedestal type water closet

(European Type) with seat and lid, 10 litre low level white viterous china

flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm

2 17.3 flush bend, overflow arrangement with specials of standard make and

mosquito proof coupling of approved municipal desing complete, including

painting of fittings and brackets, cutting and making good the walls and

floors wherever required:

17.3.1 W.C. pan with ISI marked white solid plastic seat and lid Each 12.00 7790.42 ₹ 93,485.04

Providing & fixing white vitreous china Under Counter wash basin with

C.I. brackets painted white, with rubber plug, 32mm C.P. brass waste of

standerd pattern including cutting & making good the walls wherever

a)White Vitreous China Wash basin size (609x410x167)mm . Each 36.00 7356.98 ₹ 2,64,851.33

@4% on Providing and fixing P.V.C. waste pipe for sink or wash basin including

DSR 2023 P.V.C. waste fittings complete.

Providing and fixing bevelled edge 6mm mirror of superior glass (of

5 MR approved quality) complete with 6mm thick hard board ground fixed to SQMTR 36.00 2463.88 ₹ 88,699.67

wooden cleats with C.P. brass screws and washers complete.

Providing and fixing white vitreous china battery based infrared sensor

operated urinal of approx. size 680 x 305 x 350 mm having pre & post

6 MR flushing with water (250 ml & 500 ml consumption), having water inlet Each 24.00 11183.85 ₹ 2,68,412.43

from back side, including fixing to wall with suitable brackets all as per

manufacturers specification and direction of Engineer-in-charge. .

Providing and fixing stone slab table rubbed, edges rounded and polished

of size 75x50cm deep and 1.8cm thick fixed in Urinal partitions by cutting

a chase of appropriate width with chase cutter and embedding the stone

in the chase with epoxy grout or with cement concrete 1:2:4 (1cement:

2coarse sand: 4graded stone aggregate 6mm nominal size) as per

direction of Engineer-in-charge and finished smooth.

8.10.2 Granite Stone of approved shade Each 24.00 3942.45 ₹ 94,618.80

CP Brass fittings

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1

metre long with S.S. triangular plate to Eureopean & Wall moutain type

W.C. of quality and make as approved by Engineer - in - charge.(Health

Providing and fixing C.P. brass two way bib cock of approved quality

conforming to IS:8931 .

a) 15 mm nominal bore Each 24.00 1589.86 ₹ 38,156.67

Providing and fixing of 200 mm dia CP Shower rose with 15 mm to 20

10 MR mm inlet including bath spout wall diverter with all fittings. (For Each 36.00 9676.22 ₹ 3,48,344.07

Common toilet and Servent Toilet.)

Providing and fixing C.P. brass angle valve for basin mixer and gyser

points of approved quality conforming to IS:8931 .

a) 15 mm nominal bore Each 27.00 629.27 ₹ 16,990.30

Central Hole waste coupling without Popup Waste System with 32mm full

Providing and fixing basin diverter mixer wall mounted basin mixer upper

13 M.R. trim with concealed body. Each 36.00 7236.61 ₹ 2,60,517.95

Providing and fixing C.P. brass stop cock (concealed) of standard design

and of approved make conforming to IS:8931:

Providing and fixing CP Brass 32mm size Bottle Trap of approved quality

& make and as per the direction of Engineer-in-charge.

Providing and fixing SS liquid soap container 109 mm wide, 125 mm high

and 112 mm distance from wall of standard shape with bracket of the

same materials with snap fittings of approved quality and colour,

weighing not less than 105 gms.

Digitally signed by SUJEET

Providing and fixing SS towel rail complete with brackets fixed to wooden

19 MR cleats with CP brass screws with concealed fittings arrangement of

approved quality and colour.

600 mm long towel rail with total length of 600 mm, 78 mm wide and

effective height of 88 mm, weighing not less than 170 gms..

20 MR Providing and fixing SS towel ring Each 36.00 1140.55 ₹ 41,059.89

21 MR Providing and Fixing SS Toilet Paper Holder. Each 12.00 1387.26 ₹ 16,647.06

22 MR Providing and Fixing soap dish holder. Each 72.00 1016.61 ₹ 73,195.59

23 MR Providing and Fixing double coat hook. Each 36.00 802.08 ₹ 28,874.93

Supply and installation of corner glass shelf for toilet made of toughened

(tempered) safety glass, 8 mm to 10 mm thick, clear / frosted / tinted as

specified, with polished and rounded edges and corner safety chamfers.

Shelf size shall be 250 × 250 mm (±25 mm) triangular type suitable for

corner mounting, capable of withstanding normal bathroom load without

24 MR deflection. The shelf shall be supported on heavy-duty stainless steel Each 36.00 1096.46 ₹ 39,472.42

Grade SS 304 brackets / clamps with chrome or satin finish, complete

with stainless steel screws, wall plugs and concealed fittings. Installation

shall include accurate alignment, drilling, fixing, sealing with clear silicone

sealant, and making good wall finishes, fixed true to line and level,

complete in all respects.

25 MR Providing and fixing CP Brass toothbrush/toothpaste holder. Each 36.00 1171.54 ₹ 42,175.42

Supply and installation of grab bar for toilet made of high-quality

stainless steel Grade SS 304, 32 mm to 38 mm diameter, seamless pipe

with minimum 1.2 mm thickness, having satin/matt finish, corrosion-

resistant and easy to clean, complete with concealed wall mounting

flanges, stainless steel screws, rawl bolts and all necessary fittings. Grab

27 MR bar shall be wall mounted / angle / straight / L-shaped / U-shaped as Each 12.00 1480.22 ₹ 17,762.59

specified, capable of withstanding a minimum load of 150 kg, installed at

required height as per CPWD / NBC / Accessibility guidelines, fixed firmly

on RCC or brick wall with proper backing support, including cutting,

making good the wall surface, testing and making the installation fully

functional, complete in all respects.

Supply and installation of hinged support rail for toilet made of heavy-

duty stainless steel Grade SS 304 (SS 316 for coastal or high-corrosion

areas), 32 mm to 38 mm diameter seamless pipe with minimum 1.2–1.5

mm wall thickness, finished in satin/matt anti-slip finish, complete with

nylon or rubber hand grip sleeve (where specified). Hinged rail shall be

foldable (up/down movement) with smooth action, equipped with locking

or friction hinge mechanism to hold position, and provided with concealed

wall fixing flange using stainless steel fasteners, anchor bolts and

necessary backing plates. The rail shall be capable of supporting a

minimum load of 150 kg, installed at required height and orientation as

per NBC / CPWD / Accessibility norms, including all accessories, cutting,

making good the wall surface and testing, complete in all respects.

29 Providing & fixing soil, waste and vent pipes.

Hubless centrifugally cast (spun) iron pipes epoxy coated inside & outside

17.35.1.3 a) 100mm dia centrifugally cast iron S & S pipe. MTR 249.00 1137.73 ₹ 2,83,294.77

17.35.2.3 b) 75mm dia centrifugally cast iron S & S pipe. MTR 243.00 938.22 ₹ 2,27,987.46

Providing and fixing PVC pipes complete with all fittings and clamps,

including cutting and making good walls etc. ( for wash basin waste )

MR 32mm dia nominal bore MTR 69.00 102.77 ₹ 7,091.13

Providing and fixing shielded coupling for Hubless centrifugally cast iron

SS 304 grade coupling with EPDM rubber gasket

Providing & fixing M.S. holder bat clamps of approved design to sand cast

iron/centrifugally cast (Spun) iron S & S pipe embeded in & including

cement concrete blocks 10x10x10cm. of 1:2:4 mix (1 cement : 2 coarse

: 4 graded stone aggregate 20mm nominal

size). Including cost of cutting holes & making good the walls etc.

Providing and fixing trap of self cleansing design with screwed down or

33 hinged grating with or without vent arm complete, including cost of

cutting and making good the walls and floors :

34 MR. Providing and fixing 100x100 mm ss jali for trap. Each 108.00 308.68 ₹ 33,337.03

Providing and fixing plain bend of required degree cast (spun) iron cast

(spun) iron material epoxy coated inside & outside IS:15905

Providing and fixing single equal plain junction of required degree with

access door, insertion rubber washer 3 mm thick, bolts and nuts

complete. (Y Bend with Door) cast (spun) iron cast (spun) iron

material epoxy coated inside & outside IS:15905

Digitally signed by SUJEET

Providing and fixing centrifugaly cast iron single equal plain junction of

37 required degree cast (spun) iron cast (spun) iron material epoxy coated

inside & outside IS:15905 . (Plain Y Bend)

Providing and fixing door piece, insertion rubber washer 3mm thick, bolts

& nuts complete material sand cast iron IS 3989 :( c.o.p.)

39 Providing and fixing cast iron terminal guard sand cast iron IS 3989 .

Providing and laying cement concrete 1:5:10(1 cement : 5 coarse sand :

10 graded stone aggregate 20mm nominal size) around P.V.C Soil and

40 waste pipe including bed concrete as per standard design(embedded in

the flooring / ground).( For manhole connection rain water & soil waste

Providing and fixing on wall face unplasticised-Rigid PVC rain water pipes

41 12.41 conforming to IS: 13592 Type A including jointing with seal ring

conforming to IS: 5382 leaving 10mm gap for thermal expansion.

Providing and fixing on wall face unplasticised PVC moulded

fittings/accessories for unplasticised Rigid PVC rain water pipes

conforming to IS:13592 Type A including jointing with seal ring

conforming to IS:5382 leaving 10mm gap for thermal expansion.

12.42.1 Coupler

12.42.5.2 Bend 87.5 degree

12.42.6 SINGLE TEE WITHOUT DOOR

Providing and fixing to the inlet mouth of rain water pipe cast iron grating

15 cm diameter and weighing not less than 440 grams.

Making khurras 45x45 cm with average minimum thickness of 5 cm

cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone

aggregate of 20 mm nominal size) over PVC sheet 1m x 1 m x 400

micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse

sand) and a coat of neat cement,punning,rounding the edges and making

and finishing the outlet complete.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having

thermal stability for hot & cold water supply including all CPVC plain &

brass threaded fittings i/c fixing the pipe with clamps at 1.00m spacing.

52 This includes jointing of pipes & fittings with one step CPVC solvent

cement and the cost of cutting chases and making good the same

including testiang of joints complete as per direction of Engineer in

Concealed work including cutting chases and making good the walls etc.

18.8.1 15mm dia nominal outer dia pipes Mtr 114.00 484.36 ₹ 55,217.04

18.8.2 20mm dia nominal outer dia pipes Mtr 219.00 523.08 ₹ 1,14,554.52

18.8.3 25mm dia nominal outer dia pipes Mtr 144.00 610.31 ₹ 87,884.64

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having

thermal stability for hot & cold water supply, including all CPVC plain &

brass threaded fittings, including fixing the pipe with clamps at 1.00 m

spacing. This includes jointing of pipes & fittings with one step CPVC

solvent cement and testing of joints complete as per direction of Engineer

18.7.4 32mm dia nominal bore Mtr 111.00 504.74 ₹ 56,026.14

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having

thermal stability for hot & cold water supply including all CPVC plain &

54 brass threaded fittings This includes jointing of pipes & fittings with one

step CPVC solvent cement, trenching, refilling & testing of joints complete

as per direction of Engineer in Charge.

55 18.17 Providing and fixing gun metal gate valve with wheel of approved quality.

18.17.3 40mm dia nominal bore each 27.00 803.80 ₹ 21,702.60

18.17.6 80mm dia nominal bore each 6.00 2534.23 ₹ 15,205.38

Providing and fixing ball valve (brass) of approved quality, High or low

pressure, with plastic floats complete :

Digitally signed by SUJEET

Supply of wall hanging drinking online water cooler with bottle filler

facility, made by stainless steel top and heavy duty galvanized steel

frame. With cooling capacity, ADA Compliant, size 472 mm Depth X

447mm width, flexible bubbler guard , operated between 50 to 120 PSI,

Chiller unit Suitable to R134a Refrigerant, Adjustable thermostat control,

57 M.R. suitable for 220-230v/50-60 hz A/C Supply Complete with all accessories Each 12.00 92513.48 ₹ 11,10,161.70

which include MD-CU29, which is an EPA registered antimicrobial copper

that fights off microorganisms which include MRSA and e-coli. The water

Fountain shall possess NSF-USA, Green building, energy star saving

certification, and to be placed at different location of buidling. As per

Enginner Incharge- Make Oasis/ Filtrin/ Eureka Forbes

Supply, installation, testing, and commissioning of electric storage-type

geyser of 25-litre capacity, 2.0 kW, 230 V, single-phase, 50 Hz, vertical

wall-mounted type, complete with thermostat control, automatic thermal

cut-off, pressure relief valve (PRV), non-return valve (NRV), and all

standard safety devices. The geyser shall have a glass-lined or stainless-

steel (SS-304 grade) inner tank with high-density PUF insulation, rust-

proof ABS or powder-coated MS outer body, and adjustable temperature

range from 25°C to 75°C. The scope includes providing ISI-marked inlet

and outlet flexible connections, pressure release and drain pipe, wall-

mounting brackets, electrical connections, and all materials, tools, and

labor required for proper installation. The work shall be carried out as per

standard specifications, tested and commissioned to the satisfaction of

the engineer-in-charge, with a minimum warranty of 2 years on the

product and 5 years on the inner tank.

Providing and fixing motorized butterfly valves the valve should be able

to oprate with hot/cold water medium between 20---120 degree working

temperature, the nominal pressure of the valve should be PN 16, leakage

rate through the valve disc should be Rate-A Bubble tight to EN1266-1

with integrated flange sealing should ensure positive connection of the

valve body seat ring and valve disc and provide a complete isolation of

the media from the body. The disc casting should be precision machined

and should give a smooth and close disc-to-seat relationship. The stem

bearing should comprise of non corrosive PTFE bushing to completely

isolate the valve seat from the body, resulting in increase control of the

valve disc, lower valve seating torque and longer valve life. The disc

should be stainless steel to offer a good corrosion resistance, superior

resistance to a broad range of chemical enviorments as well as very low

co-efficient of friction and excellent resistance to impact and ultra-violet

radiation. For temperatures and rust proof operation the valve disc should

be stainless steel material.

Providing and fixing water meter flange end woltman water meter class A

Providing and fixing pressure release valve with wheel of approved

32mm dia nominal bore each 24.00 5551.40 ₹ 1,33,233.71

DSR Amount Non DSR Amount

Gross Total DSR Amount ₹ 35,90,488.00

Total Non DSR Amount ₹ 39,39,432.00

DSR AMOUNT Non DSR AMOUNT

GROSS TOTAL PLUMBING WORK ₹ 75,29,920.00

Digitally signed by SUJEET

Construction of Vertical extension for an additional floor over the existing buildings of Hostel No. 7, 8 & 9 at NIT Kurukshetra.

(Electrical Works)

S.No. Description of Item Quantity Rate (Rs) DSR Amount(Rs) NON DSR AMOUNT (Rs)

Sub-Head : WIRING

Wiring for light point/ fan point/ exhaust fan point/ call bell

point with 1.5 sq.mm FRLS/HFFR PVC insulated copper

conductor single core cable in surface/ recessed medium class

1 1.10 PVC conduit, with modular switch, modular plate, suitable GI

box and earthing the point with 1.5 sq.mm FRLS/HFFR PVC

insulated copper conductor single core cable etc. as required.

Wiring for twin control light point with 1.5 sq.mm FRLS/HFFR

PVC insulated copper conductor single core cable in surface /

recessed medium class PVC conduit, 2way modular switch,

2 1.11 modular plate, suitable GI box and earthing the point with 1.5 Point 42.00 ₹ 1,803.00 ₹ 75,726.00

sq.mm FRLS/HFFR PVC insulated copper conductor single

core cable etc. as required.

Wiring for circuit/ submain wiring along with earth wire with

the following sizes of FRLS/HFFR PVC insulated copper

3 1.14 conductor, single core cable in surface/recessed medium class

PVC conduit as required.

Add cost 4 X 6 sq. mm + 2 X 6 sq. mm earth wire

Add cost 4 X 10 sq. mm + 2X6 sq. mm earth wire

Supplying and fixing following modular switch/ socket on the

4 1.24 existing modular plate & switch box including connections but

excluding modular plate etc. as required.

Supplying and fixing following size/ modules, GI box along

5 1.27 with modular base & cover plate for modular switches in

recess etc. as required.

1.35 Installation, Testing, Commissioning of wall bracket /ceiling

6 fittings of all sizes and shapes containing upto two No. 699.00 ₹ 151.00 ₹ 1,05,549.00

GLS/CFL/LED lamps per fitting, complete with all accessories

including connections etc. as required.

Installation of exhaust fan in the existing opening, including

7 1.50 making good the damage, connection, testing, commissioning

etc. as required.

Extra for fixing the louvers/ shutters complete with frame for

a exhaust fan of all sizes.

Supplying & fixing suitable size Gl box with modular plate and

cover in fronton surface or in recess including providing and

9 1.57 fixing 25 A modular socket outlet and 25 A modular SP MCB, No. 36.00 ₹ 807.00 ₹ 29,052.00

"C" curve including connections, painting etc. as required.

Supplying and fixing PVC batten/ angle holder including

connections etc. as required.

Sub-Head : MCCB, MCB & OB'S

Providing and fixing following rating and breaking capacity

and pole MCCB with thermomagnetic release and terminal

11 2.2 spreaders in existing cubicle panel board including drilling

holes in cubicle panel, making connections, etc. as required.

Supplying and fixing following way, horizontal type three pole

and neutral, sheet steel, MCB distribution board, 415 V, on

surface/ recess, complete with tinned copper bus bar, neutral

12 2.4 bus bar, earth bar, din bar, interconnections, powder painted

including earthing etc. as required. (But without

MCB/RCCB/lsolator)

Supplying and fixing of following ways surface/ recess

mounting, vertical type, 415 V, TPN MCB distribution board of

sheet steel, dust protected, duly powder painted, inclusive of

13 2.5 200 A tinned copper bus bar, common neutral link, earth bar,

din bar for mounting MCBs (but without MCBs and incomer)

as required . (Note : Vertical type MCB TPDB is normally used

where 3 phase outlets are required.)

Digitally signed by SUJEET

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C"

curve, miniature circuit breaker suitable for inductive load of

14 2.10 following poles in the existing MCB DB complete with

connections, testing and commissioning etc. as required.

Supplying and fixing single pole blanking plate in the existing

MCB DB complete etc. as required.

Supplying and fixing following rating, four pole, 415 V,

16 2.13 isolator in the existing MCB DB complete with connections,

testing and commissioning etc. as required.

Supplying and fixing following rating, four pole, (three phase

and neutral), 415 volts, residual current circuit breaker

17 2.15 (RCCB), having a sensitivity current 30 mA in the existing

MCB DB complete with connections, testing and

commissioning etc. as required.

Providing and fixing M.V. danger notice plate of 200 mm X

150 mm, made of mild steel, at least 2 mm thick, and

18 2.21 vitreous enameled white on both sides, and with inscription in No. 3.00 ₹ 315.00 ₹ 945.00

single red colour on front side as required.

Sub-Head : EARTHING

Earthing with G.l. earth plate 600 mm X 600 mm X 6 mm

thick including accessories, and providing masonry enclosure

19 5.4 with cover plate having locking arrangement and watering Set 24.00 ₹ 8,351.00 ₹ 2,00,424.00

pipe of 2.7 metre long etc. with charcoal/ coke and salt as

Supplying and laying 6 SWG G.l. wire at 0.50 metre below

20 5.7 ground level for conductor earth electrode, including Metre 240.00 ₹ 62.00 ₹ 14,880.00

connection/ termination with Gl thimble etc. as required.

Supplying and laying 25 mm X 5 mm G.l. strip at 0.50 metre

below ground as strip earth electrode, including connection/

21 5.9 terminating with G.l. nut, bolt, spring, washer etc. as Metre 240.00 ₹ 160.00 ₹ 38,400.00

required. (Jointing shall be done by overlapping and with 2

sets of G.l. nut bolt & spring washer spaced at 50mm)

Providing and fixing 25 mm X 5 mm G.l. strip on surface or in

recess for connections etc. as required.

Providing and fixing 6 SWG dia G.l. wire on surface or in

recess for loop earthing as required.

Sub-Head : MV CABLE LAYING

Laying of one number PVC insulated and PVC sheathed / XLPE

power cable of 1.1 KV grade of following size direct in ground

24 10.1 including excavation, sand cushioning, protective covering

and refilling the trench etc as required.

Laying and fixing of one number PVC insulated and PVC

25 10.7 sheathed / XLPE power cable of 1.1 KV grade of following size

on wall surface as required.

Above 95 sq. mm and up to 185 sq. mm (clamped with

25/40x3mm MS flat clamp)

Sub-Head : MV CABLE JOINTING & END TERMINATION

Supplying and making end termination with brass

compression gland and aluminium lugs for following size of

26 11.1 PVC insulated and PVC sheathed / XLPE aluminium conductor

cable of 1.1 KV grade as required.

Sub-Head : MISC. CIVIL ITEMS

Providing and fixing circular/Hexagonal G.I. Box for ceiling fan

clamps, of internal dia 140 mm, 73 mm height, top LID of 1.5

mm thick G.I. sheet with its top surface hacked for proper

27 bonding, top LID shall be screwed into the G.I. box by means Each 264.00 ₹ 142.95 ₹ 37,738.80 This item not found in DSR

of 3.3 mm dia rounded screws, one lock at the corners.

Clamps shall be made of 12 mm dia M.S. bar bent to shap as

per standard drawing. (DSR Civil-2014 item no. 10.18)

Sub-Head : LIGHT & FAN FIXTURE

28 8.2 LED Down lighter (SMD Type) (System lumen efficacy

≥120 <135 lm/Watt )

Digitally signed by SUJEET

Supplying, installation, Testing & Commissioning of LED

Recessed/surface Down lighter (Round/ square/ Rectangular)

SMD type of following body material with PMMA and prismatic

diffuser and construction as per IS : 10322 with driver as per

the requirement with Driver efficiency >85%, Operating

voltage AC 140-270 Volt, frequency 50/60 hz, Operating temp

range -5 0C to 40 0C centigrade, internal surge protection of

2.5 KV with Short & Open circuit protection ,THD < 10%, P.

F.≥0.95, IP20, CRI >80, UGR (Unified Glare Rating) <19,

Flicker free (flicker should be below 5 %), life time (LED,

Driver & electrical circuitry), life time of minimum 50000

Burning Hours with 70% of initial Lumen maintained till life

ends, CCT 3000°K / 4000°K / 5700°K /6500°K (As per ANSI

Bin), SDCM(Standard Deviation Color Matching) <3,

Maximum power consumption should not more than the

specified rating and Fixture shall be of relevant BIS standard.

Manufactures Word Mark/ Name Engraved/ Embossing/

Screen printing on housing Complete in all respect i/c external

connections with 1.5 sq mm FRLS/HFFR, PVC insulated copper

conductor single core cable and earthing etc. as required with

Minimum 5 year OEM warranty. System lumen efficacy ≥120

<135 lm/Watt output . LM79 & LM80 Test report and all

testing required for LED fixtures as per BIS shall be

submitted.. Shape size and CCT shall be as approved by

Engineer-in-Charge as per requirement. (Thermal

management: heat sink of aluminium housing such that LED

junction temperature shall not rise above 90°C).

Powder coated die cast /Extruded aluminium Body including

29 8.10 LED Batten light (System lumen efficacy ≥120 <135

Supplying, installation, Testing & Commissioning of LED

surface mounted Batten light of following body material and

construction as per IS : 10322 with driver (Replaceable) as

per the requirement with Driver efficiency >85%, Operating

voltage AC 140- 270 Volt, frequency 50/60 hz, Operating

temp range -5 0C to 40 0C, internal surge protection of 2.5

KV with Short & Open circuit protection ,THD < 10% , P.

F.≥0.95, IP20, CRI >80, Flicker free (flicker should be below 5

%), life time (LED,Driver & electrical circuitry), of minimum

50000 Burning Hours with 70% of initial Lumen maintained till

life ends, CCT 3000°K / 4000°K / 5700°K /6500°K (As per

ANSI Bin), SDCM(Standard Deviation Colour Matching) <3,

Maximum power consumption should not more than the

specified rating and Fixture shall be of relevant BIS standard.

Manufactures Word Mark/ Name Engraved/ Embossing/

Screen printing on housing. complete in all respect i/c

external connections with 1.5 sq.mm FRLS/HFFR, PVC

insulated copper conductor single core cable and earthing etc.

as required with Minimum 5 year OEM warranty. System

lumen efficacy ≥120 <135 lm/Watt output . LM79 & LM80

Test report and all testing required for LED fixtures as per BIS

shall be submitted. Shape size and CCT shall be as approved

by Engineer-in-Charge as per requirement. (Thermal

management: heat sink of aluminium housing such that LED

junction temperature shall not rise above 90°C).

Powder coated die cast / Extruded aluminium Body

(Thickness≥ 1.20 mm)

30 8.16 LED Flood Light, powder coated pressure die cast

aluminum (System lumen efficacy ≥120 and <135

Digitally signed by SUJEET

Supplying, Installation, Testing & Commissioning of Flood

Light, powder coated pressure die cast aluminium body with

built in or separate driver as per the requirement with Driver

efficiency >85%, Input voltage: Input voltage: 140-270 Volt

AC,frequency 50/60 hz, Operating temp range -5 0C to 500C,

internal surge protection of 5 KV L,N,E as per IEC 61000-4-5,

Driver efficiency >85%,THD < 10% as per IEC 61000-3-2, P.

F.≥0.95, IP-66,IK-10, CRI>70, under voltage and over

voltage protection, EMI-EMC as per CISPR-15, lenses for

beam angle 30 deg-120deg as per the application and the

project requirement, suitable tilt able fitting, life time (LED,

Driver & electrical circuitry) of minimum 50000 Burning Hours

with 70% of initial Lumen maintained till life ends as per LM80

extrapolation IES TM-21-11 report, CCT 3000°K / 4000°K /

5700°K /6500°K (As per ANSI Bin), SDCM(Standard Deviation

Colour Matching) <5, Maximum power consumption should

not more than the specified rating and Fixture shall be of

relevant BIS standard complete in all respect i/c external

connections with 1.5 sq.mm FRLS/HFFR,

PVC insulated copper conductor single core cable and earthing

etc. as required with Minimum 5 year OEM warranty. System

lumen efficacy ≥120 and <135 lm/Watt output . LM79 & LM80

Test report and all testing required for LED fixtures as per

BIS shall be submitted.. Shape size and CCT shall be as

approved by Engineer-in-Charge as per requirement.

(Thermal management: heat sink of aluminium housing such

that LED junction temperature shall not rise above 90°C).

31 9.2 Brush Less Direct Current (BLDC) Fan without

Supply, Installation, Testing and Commissioning of ceiling fan

with Brush Less Direct Current (BLDC) Motor, class of

insulation: B, 3 nos. metal( Aluminium alloy) blades, 30 cm

long down rod, 2 nos. canopies, shackle kit, safety rope,

copper winding, steel/Al body Power Factor not less than 0.9,

Service Value (CM/M/W) minimum as below, 350 RPM

(tolerance as per IS : 374-2019), THD (Total Harmonic

Distortion) less than 10%, suitable for operation with

regulator for speed control and all remaining accessories

including safety pin, nut bolts, washers, temperature rise=75

0C (max.), insulation resistance more than 2 mega ohm,

suitable for 230 V, 50 Hz, single phase AC supply, Ceiling Fan

compliant to IS 374:2019 fan i/c external connections with

1.5 sq.mm FRLS/HFFR, PVC insulated copper conductor single

core cable and earthing etc. as required.

9.2.3 1200mm, service value ≥ 6.0 CM/Min/Watt, air Each

delivery 210 CM/Min (Minimum) 264 ₹ 2,695.00 ₹ 7,11,480.00

TOTAL A (SCHEDULED ITEM) IN RS.

Sub-Head : Non-Schedule Items

Supply of AC 300mm Sweep, 230/250 Volts, 50 Hz exhaust

32 A.R. - 01 fan (Heavy Duty) with blades,cover,Louvers etc. complete as each 15 ₹ 1,232.00 ₹ 18,480.00

Supply of Factory made 12 to 20 Watt LED Bulb fitting,cool

33 A.R. - 02 day light,(65000 K temp.) suitable for Batton/Angle holder each 603 ₹ 143.00 ₹ 86,229.00

including making connection.Complete in all respect.

Supply of LED Tube Light with batten suitable for up to

34 A.R. - 03 1 X 10 watt LED tube light fitting including tube on each 36 ₹ 390.00 ₹ 14,040.00

Surface complete in all respect.(2ft)

Supply of water tight oblong 10 Watt LED bulk head

35 A.R. - 04 luminaire having die cast housing with driver set confirming to each 60 ₹ 1,425.00 ₹ 85,500.00

IP 65 and above Protection.Complete in all respect.

Supplying of aluminium conductor PVC insulated armoured

served sheathed cable 1100 volts grade.

Digitally signed by SUJEET

Supply & Erracetion of factory fabricated & wired metal

clad dust and vermin proof floor mounting, M.S. Channel

Base with bottom and top cable entreis Electrical

control panel with TPN MCCB's (Four Pole 36 KA

with thermal magnatic release)Switches Complete and

instrument chamber etc.complete in all respects. The

instrument chamber shall be separate and shall comprise

of flush type digital metering system for phase to phase

voltage and single phase voltage, current and

other parameters(KVA,P.F,KW etc) in each phase with

touch type selector switches for different readings,

instrument fuses, current transformer etc. The panel board

shall have suitable capacity electrolytic alumininum

34 AR-06 busbars as per IS8623 or above istulated with heat

shrink sleeving and mounted on non hygroscopic supports

such as CMC/BMC support with deteachable side covers

and shall be suitable for extension on the sides. The

MCCB's shall be complete with suitable cable end boxes,

compression glands and indicating lamp on

incoming etc.The Job includes the grounting of the board

as per directions of Engineer-in charge. All out goings of

100 Amp and above shall have an Ammeter. The panel

board shall be fabricated with CRCA sheet with a

minimum thickness of 1.6mm/2mm. Cubicle type switch

board shall be of cat B Only.

63 Amp. MCCB-3 Nos.+(63 AMP FPMCB-9NOS.) -

Gross Total DSR Amount ₹ 1,71,89,822.00

Total Non DSR Amount ₹ 10,96,713.00

DSR AMOUNT Non DSR AMOUNT

GROSS TOTAL PLUMBING WORK ₹ 1,82,86,535.00

Digitally signed by SUJEET

Construction of Vertical extension for an additional floor over the existing buildings of Hostel No. 7, 8 & 9 at NIT Kurukshetra.

(Fire Fighting Works)

S.No. Description of Item

Unit Quantity Rate (Rs) DSR Amount(Rs)

Sub-Head : FIRE DETECTION AND ALARM SYSTEM

1 28.2 INTELLIGENT FIRE ALARM SYSTEM

Supplying, installation, testing and commissioning of micro

processor based intelligent addressable main fire alarm panel,

central processing unit with the following loop modules and capable

of supporting not less than 240 devices (including detectors) and

minimum 120 detectors per loop and loop length up to 2 km,

network communication card, minimum 320 character graphics/

LCD display with touch screen or other keypad and minimum 4000

events history log in the non volatile memory (EPROM), power

supply unit (230 ± 5% V, 50 hz), 48 hrs back-up with 24 volt sealed

maintenance free batteries with automatic charger. The panel shall

have facility to connect printer to printout log and facility to have

seamless integration with analog/digital voice evacuation system

(which is part of the schedule of work under SH: PA System) and

shall be complete with all accessories . The panel shall be

compatible for IBMS system with open protocol BACnet/ Modbus

over IP complete as per specifications.

2 28.2.2 Supplying, installation, testing & commissioning of central

graphical fire alarm management system to centrally monitor

and operate the fire alarm system complete as required. No. 3.00 2,10,264.00 6,30,792.00

3 28.2.10 Supplying, installation, testing & commissioning of addressable

fire control module complete as required. No. 120.00 3,156.00 3,78,720.00

4 Add cost Supplying, installation, testing & commissioning of addressable

items manual call point complete as required. No. 120.00 4,063.00 4,87,560.00

5 Add cost Supplying, installation, testing & commissioning of addressable

M) items horn cum strobe complete as required. No. 120.00 3,682.00 4,41,840.00

CABLING & WIRING

6 28.5.2 Supplying & laying of 2x1.5 sqmm fire alarm armoured cable,

600/1000V rated with annealed copper conductor having XLPE

insulation, steel wire armouring & ERLS outer sheath complete

7 27.4 Supplying, installation, testing and commissioning of electric

driven terrace pump suitable for automatic operation and

consisting of following, complete in all respects, as required:

a) Horizontal type, multistage, centrifugal, split casing pump of

cast iron body & bronze impeller with stainless steel shaft,

mechanical confirming to IS : 1520

b) Suitable HP squirell cage induction motor TEFC type suitable

for operation on 415 volts, 3 phase, 50 Hz, AC supply with

IP55 class of protection for enclosure, horiziontal foot mounted

type with Class-'F' insulation, conforming to IS-325.

c) M.S.fabricated common base plate, coupling, coupling

guard, foundation bolts etc.as required.

d) Suitable cement concrete foundation duly plastered and

with anti vibration pads.

8 27.7 Providing, laying, testing & commissioning of 'C' class heavy

duty MS pipe conforming to IS 3589/IS 1239 including

Welding, fittings like elbows, tees, flanges, tapers, nuts bolts,

gaskets etc. and fixing the pipe on the wall/ceiling with suitable

clamp/support frame and painting with two or more coats of

synthetic enamel paint of required shade complete as required

Digitally signed by SUJEET

9 27.9 Supplying and fixing single headed internal hydrant valve with

instantaneous Gunmetal/Stainless Steel coupling of 63 mm dia

with cast iron wheel ISI marked conforming to IS 5290 (Type -

A) with blank Gunmetal/Stainless Steel cap and chain as

27.9.2 Single headed Stainless steel Set 54.00 6,632.00 3,58,128.00

10 27.11 Supplying, fixing, testing and commissioning of butterfly valve

of PN 1.6 rating with bronze/gunmetal seat duly ISI marked

complete with nuts, bolts, washers, gaskets conforming to IS

13095 of following sizes as required :

11 27.13 Supplying and fixing orifice plate made out of 6 mm thick

stainless steel (Grade 304) with orifice of required size to be

fitted between flange & landing valve of external and internal

hydrants to reduce pressure at the outlet to the level of 3.5

kg/cm2 complete as required. No. 54.00 1,436.00 77,544.00

12 27.14 Providing, installation, testing and commissioning of non-return

valve of following sizes confirming to IS: 5312 complete with

rubber gasket, GI bolts, nuts, washers etc.as required :

13 27.15 Providing, installation, testing and commissioning of stainless

steel Y-strainer fabricated out of 1.6 mm thick stainless steel,

Grade 304, sheet with 3 mm dia holes with stainless steel

14 27.16 Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with

63 mm dia male and female couplings duly bound with GI wire,

rivets etc. conforming to IS 636 (type-A) as required :

27.16.2 Stainless Steel (Grade 304) Set 108.00 4,667.00 5,04,036.00

15 27.17 Supplying and fixing first-aid Hose Reel with MS construction

spray painted in post office red, conforming to IS 884 complete

with the following as required. 20 mm nominal internal dia

water hose thermoplastic (Textile reinforced) type -2 as per

IS: 12585 20 mm nominal internal dia gun metal globe valve &

Drum and brackets for fixing the equipmets on wall.

Connections from riser with 25 mm dia stop gun metal valve &

M.S. Pipe and socket.

16 27.18 Supplying & fixing 63 mm dia gun metal short branch pipe with

20 mm nominal internal diameter size nozzle conforming to IS

903 suitable for instantaneous connection to interconnect hose

pipe coupling as required :

27.18.2 Stainless Steel (Grade 304) Nos. 54.00 3,402.00 1,83,708.00

17 27.19 Supplying and fixing of fire brigade connection of cast iron

body with gun metal male instantaneous inlet couplings

complete with cap and chain as reqd. for suitable dia MS pipe

connection conforming to IS 904 as required :

18 27.22 Providing & fixing of pressure switch in M.S. pipe line including

connection etc. as required. No. 54.00 1,670.00 90,180.00

19 27.24 Providing, fixing, testing & commissioning of installation control

valve of cast iron body, brass/bronze working parts comprising

of water motor alarm, bronze seat clapper, clapper arm and

hydraulically driven mechanical gong bell to sound continuous

alarm when the wet riser/sprinkler system activates, pressure

gauges, emergency releases, strainer, pressure switch, cock

valve complete with drain valve and bypass, test control box,

ball valves, MS pipe of required size, flanges, orifice plate,

gasket etc of follwing sizes as required :

TOTAL A (SCHEDULED ITEM) IN RS. 79,71,684.00

FIRE EXTINGUISHERS

Digitally signed by SUJEET

20 AR-08 Supply and fixing of fire extinguisher, ABC Type (ISI Marked

IS : 15683 & TAC approved) complete with initial charge and

wall bracket,along with supply of all materials and labour for

proper completion of work.

21 AR-09 Supply and fixing of C02 type fire extinguisher (ISI Marked IS

: 2878 & TAC approved) complete with initial charge and wall

bracket, along with supply of all materials and labour for

proper completion of work.

22 AR-10 Providing & fixing carbon steel Fire Man Axe with rubber

insulated handle tested to 20000 volts. Each 54.00 822.00 16,272.00

23 AR-11 Supplying and installing at approved location approved make

fire buckets of 24 gauge galvanized steel sheet, standard of

round bottom shape, painted white inside and red outside and

black on the bottom, inscribed with letter "FIRE" in black and

gold. Cost shall be inclusive of providing MS stand duly painted

over a coat of primer (one stand shall be suitable for hanging 5

24 AR-12 1200x900 mm (Indoor Cabinet) Only Frame Each 54.00 7,969.00 4,30,326.00

25 AR-13 Providing and Fixing of Self illuminated /Auto Glow Exit

Signs printed on photo-luminescent sheet containing self

illuminated base chemical,of appropriate size not less than

400x150mm,suspended from ceilling or fixed to the walls with

accessories as riquired and as directed at site. Each 162.00 3,520.00 5,70,240.00

26 AR-14 Providing & fixing cast iron air release valve of 25 mm dia

including 25 mm dia Ball valve with fittings etc. as per the

TOTAL B (NON-SCHEDULED ITEM) IN RS. 24,27,360.00

Digitally signed by SUJEET

Construction of Vertical extension for an additional floor over the existing buildings of Hostel No. 7, 8 & 9 at NIT Kurukshetra.

S.No. E&M DSR Description of Item Unit Qty. RATE Amount In Rs.

1 SOLAR PHOTO VOLTAIC POWER GENERATION SYSTEM

Supplying, installation, testing and commissioning of grid interactive roof top solar photo voltaic power

generation system including space frame

Roof Top Supplying Installation, Testing and Commissioning of on-grid Solar Photovoltaic Power Plant conforming

Solar to various applicable standards BIS, IEC, MNRE guidelines, the Central Electricity Authority Regulations

PVPower and CPWD Specifications as amended up to date, consisting of Mono/Poly Crystalline silicon solar cells

Plant module, net metering facility, necessary control, protections, earthing, cabling, mounting structure, junction

boxes, power conditioning units,

Real time online web interfaced Data Monitoring System, Distribution panels, grid connecting

arrangement, conduits, pipes, cable trays and other accessories etc. as required. a) High Energy

Efficiency Solar Photovoltaic Module of capacity 330 Wp or above, manufactured in India, conforming to

IS 14286/IEC 61215, IS/IEC 61730- Part-1, IS/IEC 61730-Part-2. Solar Photovoltaic Module conversion

efficiency shall not be less than 23% at STC with temperature coefficient of Pmax

better than -0.30% per 0C. PV modules used in solar power plants/ systems must be warranted for their

output peak watt capacity, which should not be less than 90% at the end of 10 years and 80% at the end

of 25 years. Solar Modules shall be designed to operate in relative humidity upto 100% with temperature

between -10 0C and +85 0C. Further, each PV module used in any solar power project must have Radio

frequency identification tag with information such as

name of manufacturer, month and year of manufacturing, country of origin (separately for Solar cell and

module), I-V curve, Unique Serial No and Model No of the module, Wattage, Im, Vm and FF,

name of test lab issuing IEC certificate. b)Power Conditioning Unit (PCU) of 350-800 V DC Input voltage

range and 415 V AC, three phase, 4 wire, 50Hz +/- 2.5 Hz, output voltage suitable to generate AC with a

variation of 10% at nominal voltage. Power with efficiency not less than 97%, total harmonic distortion less

than 3% and suitable for

ambient temperature from 0 to 50 0C, Minimum IP-65 for outdoor and Minimum IP 21 for indoor, Built-in

meter and data logger, MPPT, switching devices IGBT/MOSFETs and controller Microprocessor /DSP.

PCU/inverter shall be capable of complete automatic operation including wake-up, synchronization &

shutdown. The PCU shall be able to withstand unbalanced load conforming to IEC standard with

shutdown/standby mode. It must be provided with grid islanding along with manual disconnect pole

isolation switch besides automatic disconnection. Minimum protections: Mains Under / Over Voltage, Over

current, Over/Under grid frequency, Over temperature, Surge voltage induced at output due to external

source, Short-circuit, Lightening, Anti Islanding (for grid synch. Mode) and other protections as per

applicable standards. LCD/LED display of minimum parameters: DC input voltage, DC current, AC

Voltage and current (all 3 phases, in case of 3 phase), Instantaneous & cumulative AC output power, Daily

DC energy produced and other parameters applicable standard. Communication interface RS 485 / RS

232. c) Module mounting structure: The roof top solar plant generation units shall be installed by using

supporting Aluminium/Galvanized MS structure (mass of zinc coating shall be as per IS4759 ) having

minimum head room clearance of 2.4 meter above the terrace level / ground level. The mounting structure

would be designed to sustain wind load and seismic parameter of the site of installation. All the structure

shall be design as per applicable BIS code and the material shall also confirm the applicable BIS Code.

Structural material shall be corrosion resistant and electrolytically

compatible with the materials used in the module frame, its fasteners, nuts and bolts. The suitable

arrangements for maintenance and cleaning shall be provided. d) Real time online web interfaced Data

Monitoring System complete with accessories for various parameters such as Solar Irradiance,

temperature, AC Output Voltage and current, Output Power, Power factor, DC Input Voltage and Current,

Time C14Active, Time disabled, Time Idle, Power produced and other parameters as per standard

practices. e) Array junction box & Main junction box with IP 65 protection and termination arrangement for

incoming and outgoing cable along with glands, lugs and other

accessories etc. as required. Each junction box shall be made of GRP/FRP/Powder Coated Aluminium

/cast aluminium alloy with full dust, water & vermin proof arrangement with High quality Suitable capacity

Metal Oxide Varistors(MOVs) (semiconductor diode with resistant applied voltage)/ surge arrestors and

suitable Reverse Blocking Diodes, isolation switches isolate the DC input to Inverter, copper bus bar etc.

f) Lightning, surge voltage protection, earthing C22protection and grid islanding. g) Cables:Connections &

Interconnections by C26required size IR/UV protected XLPE insulated copper conductor 1.1 kV grade

armored power and control cables(ISI Marked) along with supplying & fixing of+C27 necessary

channel/conduit, GI cable trays, supports, lugs, thimble and other accessories etc. as required. h) DC

Distribution Board And AC Distribution Panel Board: IP65, free standing, metal cladded, having

C28copper bus bar, having required protection and control gears, connection-interconnection, etc. as

Digitally signed by SUJEET

Construction of Vertical extension for an additional floor over the existing buildings of Hostel No. 7, 8 & 9 at NIT Kurukshetra.

(Elevator Works)

S.No. Description of Item Unit Qty. RATE Amount In Rs.

Supply Installation , Testing & Commissioning of LIFTS with power operated

centre opening doors and AC variable voltage & variable frequency control,car

safety & Governor, Guides, guide rails, ropes, car platform, cabin finishes

(stainless steel), car & landing doors (stainless steel), hoist motors, braking

system, Automatic Rescue Device (ARD) etc. complete as per the CPWD

Specifications and realated IS standards upto date.

10 Passenger,1.0 mps,5 stops , 5 Openings

Digitally signed by SUJEET