Annual Repair of Haryana Govt. Housing Complex, Shalimar Bagh, Delhi for the year 2021-22 (Civil Work). (RECALL)

Amount

Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete. [New HSR 30.22]

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead. 1) For thickness of tiles 10 mm to 25 mm [New HSR 5.43.1]

Providing and applying two coats white cement based putty of approved brand and manufacturer, over plastered surface and grinding the surface smooth with sand paper to get en even and smooth finish including cost and carriage of all material , labour charges, scaffolding, sundries etc. complete. [New HSR 11.58]

Regarding terracing of mud phaska covered with tiles or brick, in cement mortar by dismantling tiles or bricks, removing mud plaster, preparing the surface of mud phaska to proper slope, relaying mud plaster gobri leaping and tiles or bricks, grouted in cement mortar 1 :3 (1 cement : 3 fine sand), including replacing unserviceable tiles or bricks with new ones and disposal of unserviceable material to the dumping ground (the cost of the new tiles or brick excluded), all complete as per direction of Engineer-in-Charge. [New HSR 30.9]

Providing gola 75x75 mm in cement concrete 1 :2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1 :3 (1 cement : 3 fine sand) as per standard design : 1) In 75x75 mm deep chase [New HSR 9.17.1]

Providing and laying of conglomerate floor 40mm thick cement concrete topping 1 :2:4 [New HSR 10.8]

Providing and fixing ceramic & Glazed tiles/ vitrified tiles/ of any size of approved make in floors / dados, laid in any pattern as specified over base of 3 mm thick adhesive of reputed brands as per IS specification 15477-2004 using 5 Kg. adhesive per sqm area of tiles and jointed with white cement slurry mixed with pigment to match the shade of tiles excluding cost of tiles.

Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq.meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground, all complete as per direction of Engineer-in-Charge. 1) With cement mortar 1 :4 ( 1 cement : 4 fine sand) [New HSR 30.16.1]

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : 1) One or more coats on old work [New HSR 30.28.1] [LR]

Distempering with dry distemper of approved brand and manufacture (one or more coats) and of required shade on old work to give an even shade. [New HSR 30.24] (Labour Rate) (Material should be provided by the department)

Providing and fixing glazed shutters for doors, windows and clerestory windows using 4 mm thick float glass panes, including ISi marked M.S. pressed butt hinges bright finished of required size with necessary screws. 2) Kiln seasoned and chemically treated Hollock wood 1) 35 mm thick [New HSR 12.10.2.1]

Providing and fixing wire gauge shutters using galvanized M.S. wire gauge of average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm, for doors, windows and clerestory windows with hinges and necessary screws: 1) 35 mm thick shutters 1) with ISi marked M.S. pressed butt hinges bright finished of required size 2) Kiln seasoned and chemically treated Hollock wood. [New HSR 12.19.1.1.2]

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 1) 35 mm thick including ISi marked Stainless Steel butt hinges with necessary screw [New HSR 12.37.1]

Renewing glass panes, with wooden fillets wherever necessary: 1) Float glass panes of nominal thickness 4 mm (weight not less than 10 kg/sqm) [New HSR 30.55.1]

Grinding and polishing of existing of marble flooring as per requirement of Engineer-in-Charge. [NS]