WBPWD/SSEWEC/BED /NIQ-24/2025-26

Make : OTIS / KONE/SCHINDLER

Type: Passenger Lift .

Load : 16 Passenger / 1088 Kg .

Control: Microprocessor based with AC variable voltage & variable frequency ( VVVF).

Machine:- Energy efficient machine, Gearless, With Machine Room.

Position of Machine Room: Directly above the Hoistway.

Speed:1.0 Mtrs./ Sec

Floor served: G+2

Landing: 3 all on same side

Total Rise : 11 Mtr (Approx) (Bidder should visit the site)

Operation: Microprocessor based implex full collective with or without attendant.

Signals: Digital car position indicator,car travels direction indicator in car & at all landing with call registration indicator.

Leveling accuracy: ±5 mm(Micro levelling arrangement)

Car inside : 1600 mm ( W ) x 1000 mm ( D ) x 2400 mm (H) or As per manufacturer's standard conforming to IS.

Car Entrance : Clear Opening 900 mm (W) x 2400 mm (H) protected with car door.

Car Enclosure: Stainless Steel sheet (20 SWG) with Hairline finish with hand rail.

Car Ceiling & Lighting: Stainless Steel with hairline finish with LED lighting and Fan.

Car Ventilation: Pressure fan with anodised aluminium grill.

Car Flooring : Decorative granite flooring (As per direcion of EIC and according to this Department's Order).

Car Door: Stainless Steel centre opening automatic door provided with V3F controlled door drive system.

Landing Door: Stainless steel centre opening automatic door provided with V3F controlled door drive system

Door Opening: Automatic power oprated door with full length Photocell assembly light curtain sensor.

Car operating panel : A best quality Screen touch car operating panel with floor indication and digital hall position & direction indicatiors.

Landing operating panel : A best quality Screen touch car operating panel with floor indication and digital hall position & direction indicatiors.

Fire Rated Door : 2 Hours

PROTECTIVE DEVICES & OTHER ACESSORIES

ARD: Automatic rescue device complete with dry maintenance free batteries as required for automatic evacuation to the nearest floor in case of power failure / single phasing/others.

Overload Protection:Fully loaded with overload protection.On overloading the lift car will not start with door remaining open and give audio display indication

Emergency lighting in car: Battery operated emergency lighting in the lift car.

Intercom system: Battery operated intercom system in Lift Car, Machine Room & Control Room

Emergency Alarm: Battery operated alarm bell system in lift car and control room

Fireman switch:Fireman switch at main landing terminal.

Voice Synthesizer: Voice announcement system (Voice Synthesizer) in the car to announce the position of the elevator in the hoist way as the car passes or stops at a floor served by the elevator.

Main rope - Belt Type (Flat Coated steel belt with V groove / Sreel rope)

Communication & Monitoring the Lift : Lift controller/ Panel shall be Ethernet/Modbus ready with necessary converter, DC Power supply module etc. if required, and there shuld be single Ethernet/Modbus output from the Controller/panel and the same should be connected to BMS (Building Management System) and the controller/ panel should have also required for monitoring of real time data with date & time, maintenance-call back record, Mantrap notice, call records, location of car, Lift room temperature etc. should be noticed & display to in any desktop & mobile though wireless system.

Other works: Necessary cutting of wall/floor for fixing the Fire Alarm switch, all Button switch and also making provision to entry of rope, electric wire etc. as required to complete the job.

DIMENSION OF SHAFT & POWER SUPPLY

Available Shaft Dimension: 2300(W) mm X 2000(D)mm (Bidder should visit the site)

Pit Depth : 1600 mm (Bidder should visit the site)

Overhead : 4200 mm (Bidder should visit the site)

Electric power supply: AC 415 Volt 3phase, 50 Hz, terminated in machine room as per IS.

Terms & Condition

i) The Agency must procure the materials from the Manufacturer / OEM or from their authorised sales channel so that the standard warranty / support of the Manufacturer / OEM becomes applicable to the products to be delivered and installed by them.

ii) Documents that authenticates such procurement from the Manufacturer / OEM or from their authorized sales channel and standard warranty / support should be sent from the e-mail of the Manufacturer / OEM / authorized sales channel to the e-mail of Engineer-in-Charge and hard copy of it to be submitted during execution, of work/submission of bill.

iii) The rate quoted by the manufacturer should be inclusive of cost for providing 2 years DLP after completion of 1 year of initial commisioning.

iv) Rates should be quoted with minor civil works, wall cutting and mending good the damages to the original finish.