WELCOME MAINTENANCE AND CERTAIN MISC BR REPAIRS TO MD ACCN AT BALASORE AND REPAIR REPLACMENT OF INTERNAL WIRING AND REPLACEMENT OF LIGHT FITTING AND FIXTURE UNDER WELCOME MAINTENANCE TO MD ACCN AT BALASORE AND NILGIRI

Amount

NOTE (Applicable for all items) :- The bidders/contractors are advised to read tender document & all corrigendum / amendments and General conditions of contracts before entrying/quoting the rates. SCHEDULE 'A' PART-I (B/R PORTION)

M&L Rendering 10mm thick on fair faces of brick work or concrete surfaces in cement mortar(CM) 1:6 and finished the surface even and smooth without using extra cement complete including taking down old cement plaster all as specified.

Dismantling and stripping the damaged wall of covering plaster by light chiseling and other manual methods until damp surfaces clean up. That might affect adhesion are to be removed by wire brushing. The entire exposed surface shall be washed thoroughly with plenty of Clean water and then allowed to dry. (Dr. FIXIT / Fosroc / SIKA / REDWOP Chemicals )

Sealing all surface shrinkage gaps on brick wall and pours shall be sealed with cementitious mortar mixed with a modified styrene butadiene emulsion. ( Dr. FIXIT / Fosroc / SIKA / REDWOP Chemicals )

Supply and Applying single coat of Polycote NPW crystalline waterproofing System against negative sides of hydrostatic heads of water for damp proofing, apply by brush. ( Dr. FIXIT / Fosroc / SIKA / REDWOP Chemicals )

Supply and Apply, covering plaster at removed damage wall surface for 10 mm thick with mixing ratio 1:4 Cement : Sand, adding adhesives styrene butadiene emulsion for plastering. (Dr. FIXIT / Fosroc / SIKA / REDWOP Chemicals

M&L for 5mm thick cement plaster in cement mortar (CM) 1:3 on ceiling, and finished the surface even and smooth without using extra cement including taking down old cement plaster complete all as directed.

M&L three coats of white wash on newly plastered surfaces of ceiling including preparation of surfaces complete all as specified and as directed.

M&L preparation of old plaster surfaces and two coat of white wash on ceiling complete all as specified and as directed.

M&L for preparation of new plastered surfaces of walls applying 2mm thick wall care putty to achieve smooth surface rubbing with sand paper and applying two coats of oil bound distemper over a coat of alkali-resiatant primer complete all as specified and directed.

M&L for preparation of old plaster surface, 1.0mm thick wall care putty on wall and two coat oil bound distemper over a coat of primer applying of decorated plastered surfaces on wall complete all as specified and as directed.

M&L preparation of old surfaces and applying one coat of synthetic enamel paint to wooden surfaces over 10 cm width or girth complete all as specified and as directed.

M&L preparation of old surfaces and applying one coat of synthetic enamel paint to steel surfaces over 10cm width or girth complete all as specified and as directed.

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing ) and rubbish off the premises.

M&L rendering 10mm thick cement plaster in CM 1:4 on fair faces of brick work for fixing of wall tiling.

M&L for 15 mm thick screed bed or bedding layer of mortar in CM 1:6 for laying floor finishes for non skid ceramic and granite tiles.

M&LGlazed ceramic tiles in vertical surface 350x 250x 7 mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match existing surfaces complete all as specified and as directed.

M&L Non Skid coloured ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.06 sqm but not exc 0.11 sqm ( 300 x 300 mm ) in floors etc set & jointed in neat cement slurry and pointed in coloured cement.

M&L Non Skid coloured ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.11 sqm but not exc 0.18 sqm ( 400 x 400 mm) in floors etc set & jointed in neat cement slurry and pointed in coloured cement.

All as Sl Item No 1.18 above but for skirting complete all as specified and as directed.

M&L for vertified ceramic tiles 10mm thick light shade (Square/rectangular) polished area of each tiles not exceeding 0.36 Sqm, in floors etc set and jointed in neat cement slurry and pointed in white or colour cement to match complete all as specified and directed.

All as Sl Item No 1.20 above for skirting complete all as specified and as directed.

M & L granite slab (of any type) 20 mm thick machine cut, bedded and jointed with gray cement slurry and pointed with white cement with admixture of pigments to match the shade of granite stone including cutting and polishing complete.

Taking up or down steel/CPVC water tubing and connecting incl cleaning for refixing or removal to stores for 15 mm bore.

Taking up or down steel/CPVC water tubing and connecting incl cleaning for refixing or removal to stores for 20 mm bore.

Supplying and laying of 16mm dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified

Supplying and laying of 20 mm dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified

S&F in repairs wash down water closet (EWC) complete white with plastic water closet seat black closed pattern with flat bottom anc cover and mild steel chromium plated or aluminised hinging device and flush pipe of polythelene of low or density or PVC 32mm dia for low level flushing cistern complete

Supply and fix Vitreous china Squatting pan Orissa pattern of size 580mx440mm wite with integral foot rests (excluding flushing cistern and flush pipe) complete including concrete bedding in repairs

Supply and fix PVC valveless syphonic action type flushing cistern 10 lit capacity low level white with inlet, ball valve, float and handle including brackets and 32mm PVC flush pipe in repairs.

Supply and fix PVC connection 15mm size with PTMT nuts of length 600mm as in repair

S&F vitreous china wash basin, white, flat back size 550x400mm, incl cutting for and pinning in ends of brackets or erecting stand but excl taps, pvc conections but incl brackets, waste pipe, waste coupling in repairs

Dismantling water tanks of capacity Exc 250 and n. exc 500 ltrs capacity.

Dismantling water tanks of capacity Exc 500 and n. exc 1000 ltrs capacity.

S&F 500 litre capacity rotational moulded polythylene water storage tank ( cylindrical vertical with closed top) hoisted and fixed in position all as per specified in SSR Part-I.

S&F 1000 litre capacity rotational moulded polythylene water storage tank ( cylindrical vertical with closed top) hoisted and fixed in position all as per specified in SSR Part-I.

S&F PVC ball valves high pressure with polythene float and fly nut complete, screwed for iron pipe of 20mm bore in repair.

S&F in repair 15 mm dia fancy type CP bib taps, cast copper alloy with crutch or butterfly handle, screwed down fixed in repairs.

S&F in repairs 15 mm dia fancy type CP pillar taps, cast copper alloy with capstan head, chromium plated screwed down fixed high pressure, long screwed shanks and fly nuts, screwed for iron pipe in repairs.

S&F in repairs 15 mm dia CP concealed type stop valves/ angular stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or unions in repairs.

S&F stainless steel sink, 0.80 mm thick for kitchen with plug, waste pipe, washer including cantilever cast iron bracket, connecting union overall size 915 mm x 460 mm with bowl size 410 mm x 330 mm x 160 mm fixed in repair

S&F Soap dish, any type, fixed to plugs with chromium plated brass screws complete all as specified and directed.

M & L health faucet Abs with Double lock 1.2 meter stainless steel flexible hose andwall hook.

S&F sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard railing 60 cm long in repairs.

S&F brass chromium plated shower rose 125 mm size fixed in repair.

S&F Brass CP tubular towel rail, 20mm dia, "D" type, 60 cm long between flanges fixed in repair.

S & F curtain rod of 18mm dia SS with fancy type SS brackets, stops, rollers etc as fixed in repairs complete all as directed.

SCHEDULE 'A' PART-II (ELECTRIFICATION)

Taking down carefully copper/aluminium point wiring including sunken MS boxes (light, fans, socket or power) complete, (fittings such as switches, ceiling roses,call bell, pendants, regulators, socket etc by unscrewing from board carefully and making good disturbed surfaces of walls, floors etc complete all as specified & directed .

M&L Point wiring with two runs of FRLSH grade PVC insulated unsheathed mulri-stranded copper conductor of size 1.5 Sqmm (phase & neutral) and one run of 1.5 Sqmm FRLSH grade PVC insulated unsheathed multi-stranded copper conductor for earth continuity wire to be drawn in and including PVC rigid conduit (medium grade) of size not less than 20 mm dia and conduit accessories with concealed wiring, sunk MS sheet metal switch/Terminal box 1.2 mm thick and hylum switch board cover 3.0 mm thick fixed with brass screws with cap washers for one light / fan point controlled by one 5/6 amps, one way switch including all necessary wall cutting and making good disturbed surface with cement mortar 1:6 or PCC 1:3:6, type C-0 and matching with existing surfaces complete all as directed and specified.

M&L Point wiring with two runs of FRLSH grade PVC insulated unsheathed mulri-stranded copper conductor of size 1.5 Sqmm (phase & neutral) and one run of 1.5 Sqmm FRLSH grade PVC insulated unsheathed multi-stranded copper conductor for earth continuity wire to be drawn in and including PVC rigid conduit (medium grade) of size not less than 20 mm dia and conduit accessories with concealed wiring, sunk MS sheet metal switch/Terminal box 1.2 mm thick and hylum switch board cover 3.0 mm thick fixed with brass screws with cap washers for for one 5/6 amps socket outlet on same board controlled with other switch complete all as directed and specified.

M&L Point wiring with two runs of FRLSH grade PVC insulated unsheathed mulri-stranded copper conductor of size 1.5 Sqmm (phase & neutral) and one run of 1.5 Sqmm FRLSH grade PVC insulated unsheathed multi-stranded copper conductor for earth continuity wire to be drawn in and including PVC rigid conduit (medium grade) of size not less than 20 mm dia and conduit accessories with concealed wiring, sunk MS sheet metal switch/Terminal box 1.2 mm thick and hylum switch board cover 3.0 mm thick fixed with brass screws with cap washers for one 5/6 amps socket outlet on independent board controlled with one, oneway switch including all necessary wall cutting and making good disturbed surface with cement mortar 1:6 or PCC 1:3:6, type C-0 and matching with existing surfaces complete all as directed and specified.

M&L Point wiring with two runs of FRLSH grade PVC insulated unsheathed mulri-stranded copper conductor of size 4 Sqmm (phase & neutral) and one run of 4 Sqmm FRLSH grade PVC insulated unsheathed multi-stranded copper conductor for earth continuity wire to be drawn in and including PVC rigid conduit (medium grade) of size not less than 20 mm dia and conduit accessories with concealed wiring, sunk MS sheet metal switch/Terminal box 1.2 mm thick and hylum switch board cover 3.0 mm thick fixed with brass screws with cap washers for one 15/16 amps socket outlet on independent board controlled with one, 15/16 amps one way switch including all necessary wall cutting and making good disturbed surface with cement mortar 1:6 or PCC 1:3:6, type C-0 and matching with existing surfaces complete all as directed and specified.

M&L Point wiring with two runs of FRLSH grade PVC insulated unsheathed mulri-stranded copper conductor of size 1.5 Sqmm (phase & neutral) and one run of 1.5 Sqmm FRLSH grade PVC insulated unsheathed multi-stranded copper conductor for earth continuity wire to be drawn in and including PVC rigid conduit (medium grade) of size not less than 20 mm dia and conduit accessories with concealed wiring, sunk MS sheet metal switch/Terminal box 1.2 mm thick and hylum switch board cover 3.0 mm thick fixed with brass screws with cap washers for one bell point controlled by one 5/6 amps, bell push including all necessary wall cutting and making good disturbed surface with cement mortar 1:6 or PCC 1:3:6, type C-0 and matching with existing surfaces complete all as directed and specified.

M&L Point wiring with two runs of FRLSH grade PVC insulated unsheathed mulri-stranded copper conductor of size 1.5 Sqmm (phase & neutral) and one run of 1.5 Sqmm FRLSH grade PVC insulated unsheathed multi-stranded copper conductor for earth continuity wire to be drawn in and including PVC rigid conduit (medium grade) of size not less than 20 mm dia and conduit accessories with concealed wiring, sunk MS sheet metal switch/Terminal box 1.2 mm thick and hylum switch board cover 3.0 mm thick fixed with brass screws with cap washers for one light point controlled by two 5/6 amps, two way switchs including all necessary wall cutting and making good disturbed surface with cement mortar 1:6 or PCC 1:3:6, type C-0 and matching with existing surfaces complete all as directed and specified.

M&L Point wiring with two runs of FRLSH grade PVC insulated unsheathed mulri-stranded copper conductor of size 1.5 Sqmm (phase & neutral) and one run of 1.5 Sqmm FRLSH grade PVC insulated unsheathed multi-stranded copper conductor for earth continuity wire to be drawn in and including PVC casing caping (heavy duty) of size not less than 20 mm width and accessories, sunk MS sheet metal switch/Terminal box 1.2 mm thick and hylum switch board cover 3.0 mm thick fixed with brass screws with cap washers for one light / fan point controlled by one 5/6 amps, one way switch including all necessary wall cutting and making good disturbed surface with cement mortar 1:6 or PCC 1:3:6, type C-0 and matching with existing surfaces complete all as directed and specified.

M&L Point wiring with two runs of FRLSH grade PVC insulated unsheathed mulri-stranded copper conductor of size 1.5 Sqmm (phase & neutral) and one run of 1.5 Sqmm FRLSH grade PVC insulated unsheathed multi-stranded copper conductor for earth continuity wire to be drawn in and including PVC casing caping (heavy duty) of size not less than 20 mm width and accessories, sunk MS sheet metal switch/Terminal box 1.2 mm thick and hylum switch board cover 3.0 mm thick fixed with brass screws with cap washers for one 5/6 amps socket outlet on independent board controlled with one, oneway switch including all necessary wall cutting and making good disturbed surface with cement mortar 1:6 or PCC 1:3:6, type C-0 and matching with existing surfaces complete all as directed and specified.

M&L Point wiring with two runs of FRLSH grade PVC insulated unsheathed mulri-stranded copper conductor of size 1.5 Sqmm (phase & neutral) and one run of 1.5 Sqmm FRLSH grade PVC insulated unsheathed multi-stranded copper conductor for earth continuity wire to be drawn in and including PVC casing caping (heavy duty) of size not less than 20 mm width and accessories, sunk MS sheet metal switch/Terminal box 1.2 mm thick and hylum switch board cover 3.0 mm thick fixed with brass screws with cap washers for one 5/6 amps socket outlet on same board controlled with other switch complete all as directed and specified.

M&L Point wiring with two runs of FRLSH grade PVC insulated unsheathed mulri-stranded copper conductor of size 4.0 Sqmm (phase & neutral) and one run of 4.0 Sqmm FRLSH grade PVC insulated unsheathed multi-stranded copper conductor for earth continuity wire to be drawn in and including PVC casing caping (heavy duty) of size not less than 20 mm width and accessories, sunk MS sheet metal switch/Terminal box 1.2 mm thick and hylum switch board cover 3.0 mm thick fixed with brass screws with cap washers for one 6/16 amps socket outlet on independent board controlled with one, 16 amps one way switch including all necessary wall cutting and making good disturbed surface with cement mortar 1:6 or PCC 1:3:6, type C-0 and matching with existing surfaces complete all as directed and specified.

M&L Point wiring with two runs of FRLSH grade PVC insulated unsheathed mulri-stranded copper conductor of size 1.5 Sqmm (phase & neutral) and one run of 1.5 Sqmm FRLSH grade PVC insulated unsheathed multi-stranded copper conductor for earth continuity wire to be drawn in and including PVC casing caping (heavy duty) of size not less than 20 mm width and accessories, sunk MS sheet metal switch/Terminal box 1.2 mm thick and hylum switch board cover 3.0 mm thick fixed with brass screws with cap washers for one bell point controlled by one 5/6 amps, bell push including all necessary wall cutting and making good disturbed surface with cement mortar 1:6 or PCC 1:3:6, type C-0 and matching with existing surfaces complete all as directed and specified.

S&F Switch piano, flush type, single pole, one way 5 Amps, 240V complete all as directed.

Fixing only in repair switch piano, flush type single pole, one way 5 Amps including connection complete all as directed.

M&L as in replacement for switch piano, flush type single pole, two way 5 Amps including connection complete all as directed.

Fixing only in repair switch piano, flush type single pole, two way 5 Amps including connection complete all as directed.

S&F as inreplacement of call bell Dingdong, 230 V AC, single pole complete all as directed.

S&F as inreplacement bell push, flush type , 5 Amp complete all as directed.

M&L as inreplacement switch socket combination 2 in 1, 5 Amps flush type including connection complete all as directed.

Fixing only in repair switch socket combination 2 in 1, 5 Amps flush type including connection complete all as directed.

M&L as inreplacement switch socket combination multipurpose 5 in 1, 5/16 Amps controlled by one switch.

Fixing only in repair switch socket combination multipurpose 5 in 1, 5/16 Amps controlled by one switch.

M&L as inreplacement switch socket outlet 2 in 1, 3 pin, 5 amp flush type controlled by one switch.

Fixing only in repair switch socket outlet 2 in 1, 3 pin, 5 amp flush type controlled by one switch.

M&L as inreplacement switch socket outlet 2 in 1, 3 pin, 5 and 15 amp flush type controlled by one switch.

Fixing only in repair switch socket outlet 2 in 1, 3 pin, 5 and 15 amp flush type controlled by one switch.

S&F as inreplacement including connection of modular switch one way 6 Amps 1 Module complete all as specified and directed.

S&F as inreplacement including connection of modular switch one way 16 Amps 1 Module complete all as specified and directed.

S&F as inreplacement including connection modular Switch socket combination 2 in 1,5 pin 5 amps 3 modules complete all as specified and directed.

S&F as inreplacement including connection modular Switch socket combination 2 in 1,6 pin 16 amps 3 modules complete all as specified and directed.

S&F as in replacement including connection modular socket outlet 2 /3 pin 6 Amps 2 modules complete all as specified and directed.

S&F as in replacement including connection modular socket outlet 2 /3 pin 6/16 Amps 2 modules complete all as specified and directed.

S&F as in replacement white modular cover plate with frame 6 Module complete all as specified and directed.

S&F as in replacement white modular cover plate with frame 8 Module complete all as specified and directed.

M & L as in replacement ceiling rose PVC poly carbonate, isolated body with three terminals including connection.

M & L as in replacement stepped type electronic fan requlator flush type 230/240 volts complete all as specified

Fixing in repair stepped type electronic fan requlator flush type 230/240 volts complete all as specified

M&L as in replacement lamp holder angular type PVC / Polycarbonate type insulated body with back plate suitable for batten fittings.

Fixing in repair lamp holder angular type PVC / Polycarbonate type insulated body with back plate suitable for batten fittings.

S&F as in replacement LED type Bulk Head fitting e TARTA 9W/10 engineering plastic housing with prismatic diffuser all as directed.

S&F as in replacement LED type basic all purpose surface and wall mounted LED batten with polycarbonate housing & integrated electronic driver 20 W,4ft tube light along with fixture white all as directed.

S&F as in replacement LED type basic all purpose surface and wall mounted LED batten with polycarbonate housing & integrated electronic driver 10 W, 2ft tube light along with fixture white all as directed.

S&F as in replacement 3mm thick PVC box of size 11" x 9 " duly cut for fixing switch piano type, switch socket combination etc complete all as specified and directed. Make : Super hylem or equivalent approved make.

All as per Sl Item No. 2.43 above but for PVC box of size 10" x 8".

All as per Sl Item No. 2.43 above but for PVC box of size 7" x 5".

All as per Sl Item No. 2.43 above but for PVC box of size 4" x 4".

Taking down ceiling fan of any type, any make and any sweep for repairing, opening the body and blade, checking for repalcement of unserviceable minor spares like nut,bolt,bush,clamp & down rod as required and cleaning, overoiling, greasing, replacement of unserviceable spare by new one, re-assembling of all components in original position, testing and hanging up the same complete all as specified and as directed by the Engr-in-Charge. Note : New spare parts required for replacement shall be measured and paid seperately as 'Supply only"

S&F as in replacement Ball bearing of size 6201/6202/6203 for ceiling fan of 1200/1400mm Sweep complete all as specified and as directed by the Engr-in-Charge. Make : TATA/SKF

Taking down exhaust fan of any type, any make and any sweep for repairing, opening the body and blade, checking for repalcement of unserviceable minor spares like nut,bolt,bush,clamp & down rod as required and cleaning, overoiling, greasing, replacement of unserviceable spare by new one, re-assembling of all components in original position, testing and hanging up the same complete all as specified and as directed by the Engr-in-Charge. Note : New spare parts required for replacement shall be measured and paid seperately as 'Supply only"

S&F as in replacement Ball bearing 2001/ 2002/ 2003 for exhaust fans complete all as specified and as directed by the Engr-in-Charge. Make : TATA/SKF

S&F as in replacement 2.5mfd capacitor complete all as specified and as directed.

S&F as in replacement 3.5mfd capacitor complete all as specified and as directed.

Material and labour for painting of ceiling fan of size 1200mm & 1400mm sweep with down rod upto 2.00 mtr long with two coats of synthetic enamel spray white paint including preparation old painted surface including writing of MES No with letters n exc 15cm height complete all as specified and as directed.

Rewinding of ceiling fan, 1200mm and 1400mm sweep with synthetic enamel copper wire including insulation of starter with polyster paper/manllex paper with cotontak binding, heat varnished and complete all as specified and as directed.

All as per Sl Item No 2.54 above but for exhaust fan of sweep exc 230mm but n exc 450mm.

Supply and fixing as in replacement M.S. galvanised louvers suitable for exhust fan of size 300/230mm sweep complete all as specified and as directed.

M/s Manas Ranjan Bera

jlenterprise

DS ENTERPRISES

M/s MANIK SETHI

M/S DK MUKHERJEE CO

vaishnaveedevienterprises

RANA ENTERPRISES

Bidder Name

RANA ENTERPRISES

DS ENTERPRISES

jlenterprise

vaishnaveedevienterprises

M/S DK MUKHERJEE CO

bholanath bera

M/s Manas Ranjan Bera

M/s MANIK SETHI