SPL REPAIR TO BLDG NO P 27 OFFRS MESS AT 2 MTN DIV ARTY BDE DINJAN MIL STN UNDER GE DINJAN

Amount

Taking down chowkhats or frames with shutter (without taking off shutter from the frame)exe 1.50 but n. exc. 4 sqm in each complete all as specified & directed.

Taking down chowkhats or frames with shutter (without taking off shutter from the frame) n. exe 1.50 sqm in each complete all as specified & directed.

S&F Pressed steel frames of size 105 x 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc. complete all as specified and as directed.

S&F 35 mm thick, 2nd class hardwood plain, factory made Plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated all as specified & directed.

S & F 35mm thick, 2nd class hard wood, glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc complete as specified and directed . Sizes of members of shutters as specified in SSR Part I, Section -8, clause 8.24(a) all as specified & directed.

Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing all as specified & directed.

S & F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; but wire gauzed i.e. panel will be of wire gauze in lieu of PVC sheet panel. The wire gauze shall be wrapped on an additional square 8mm M.S. Solid tube and this tube shall be welded to M.S. tubes. The wire gauge shall be stretched to tighten firmly as per specification & drawing., Section -8, clause 8.24(a) all as specified & directed.

M&L Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 all as specified & directed.

S&F Framed work such as grills,gratings, etc.. with ends of bars shouldered and/or riveted,or forged into spikes; framed guard bars; barred iron doors;ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 incljuding fabrication etc all as specified & directed.

Providing, cement concrete Type B1 (1:2:4) 20mm graded stone aggregate plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs not provided for in Item 04028, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, all as specified & directed.

M & L for Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp ressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length all as specified & directed. Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face)& 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moistureFactory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as specified and directed.

S & F powder coating Anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified including powder coating of minimum 50 micron thickness all as specified and directed.

S & F Powder coating anodised aluminium window and ventilator shutters, side hung type without sash, aluminium sectiion weighihg 0.55 Kg/m including necessary jointing cleats, glazing clips, rubber e packing, anodised handles 2 nos in each door, hinges, anodised aluminium snap beading screws etc, complete all as specified and directed.

S & F Powder coating anodised aluminium door shutters, aluminium sectiion weighihg 0.55 Kg/m including necessary jointing cleats, glazing clips, rubber neoprene packing, handles 2 nos in each door, hinges, anodised aluminium snap beading screws etc, complete all as specified and directed.

Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all as specified and directed.

S&F 12mm Prelaminated particle board, interior grade, prelaminated both sides with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work all as specified and directed.

S&F 3 mm thick sheet glass ordinary quality and glazing with oil putty in square exc 0.5 sq.m. each pane all as specified and directed.

S&F 4 mm thick sheet glass ordinary quality and glazing with oil putty in square n. exc 0.5 sq.m. each pane all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with puttty or fixed with beads all as specified and directed.

S&F 100 mm size, butt hinges, extruded medium weight cold rolled mild steel etc all as specified and directed.

S&F 75 mm size, butt hinges, extruded medium weight cold rolled mild steel etc all as specified and directed.

S&F 50 mm size, butt hinges, extruded medium weight cold rolled mild steel etc all as specified and directed.

S&F 150mm size, aluminium anodised handle, fabricated type all as specified and directed.

S&F 100mm size, aluminium anodised handle, fabricated type all as specified and directed.

M&L 150 mm long mild steel, barrel tower bolts of extruded section etc all as specified and directed.

M&L 100 mm long mild steel, barrel tower bolts of extruded section etc all as specified and directed.

S&F 75mm long Hasp and staple, mild steel, wire type, stove enamelled black, including bolt to hinge plate and fixed with screws all as specified and directed.

M & L for 40mm dia, cupboard knobs fixed with nut, screw and washer of mild steel, bright finished all as specified and directed.

S&F Mild steel sliding door bolts,250mm long, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed all as specified and directed.

S & F in repairs 300mm, ordinary rat tail rod pattern springs including roller and roller plate all as specified and directed.

S&F in repairs aluminium alloy Tubular towel rail 20mm dia chromium plated with fixing brackets, stops, rollers etc all as specified and directed.

S & F stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks, or galvanised wire staples all as specified and directed.

M&L for preparation of new untreated wood and wood based surfaces of any description, over 10cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of pink primer all as specified and directed.

M&L for preparation of new steel surfaces of any description, over 10cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer all as specified and directed.

M&L for preparation of old wooden surfaces of any description, over 10cm in width or girth, not otherwise described and applying one coat of synthetic enamel paint all as specified and directed.

M&L for preparation of old steel surfaces of any description, over 10cm in width or girth, not otherwise described and applying one coat of synthetic enamel paint all as specified and directed.

Dismantling of Asbestos cement (corrugated,semicorrugated, etc.) sheets in roof coverings all as specified and directed.

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified all as specified and directed.

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ as in ridge, fixed with ixed with self tapping screws all as specified and directed.

S&F 1mm Thick 150mm dia Mild steel sheet eaves gutters, galvanised class 3, half round with rounded edges

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc all as specified and directed.

M&L for Cutting out cracks to V-section in existing terracing, cleaning out and filling solidly with a hot mixture of bitumen and clean dry sand 1:1 (by weight) all as specified and directed.

M&L for Bitumen blown any grade, applied hot, two cfoats, to concrete surfaces at the rate of 1.5 Kg per Sq. m. per coat all as specified and directed.

S&F for APP based polymeric membrane minimum weighing 3Kg/sam and minimum 3mm thick reinforced with polyster non wove fabric (wt, not less than 150 gms/sqm) land on primed surfacfe by forced application all as specified and directed.

M&L for 25mm thick cement concrete B-0, 1:2:4 (12.5mm graded aggregate) finishing surfaces even and smooth without using extra cement all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floor and pavings n exc 15cm thickness (below or above ground level) all as specified and directed.

M & L PCC 1:3:6 type C-2 (50 mm) thick ( 40mm graded aggregate) thick as in plinth protection/Hard standing, etc finishing cement concrete surface even & fair whthout using extra cement making joints with bitumastic filling in proportion of bitumen and sand 1:2 complete all as specified and directed.

M & L Screed bed or bedding layer 15 mm thick in cement mortar 1:6 on floors for laying floor finish all as specified and directed.

S & F Chequrred cement concrete tiles 20 cm x 20cm x 25 mm thick, set, jointed and pointed in neat cement slurry in floors with grey cement and no pigment all as specified and directed.

M&L of Cement concrete type C2 1:3:6 (40mm graded aggregate) as in surface channels and drains all as specified and directed.

M&L Extra for forming fair finishing to drains or channel of 30 cm inner girth in cement concrete with using extra cement including forms, moulds, mitred/stopped ends etc all as specified and directed.

M & L for RCC 1:2:4 type B-1 precast concrete as in cover slab set in CM (1:4) including necessary form work complete all as specified and as directed.

Dismantling wall and celling board (fibre, pulp, insulation etc) any thickness including cover fillets all as specified and directed.

S&F 605x605mm Anodised aluminium snap grid frame work for false ceiliong all as specified and directed.

S&F Hangers 6mm dia G.I (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilinhg cleats made out of G.I. flat 40x3mm size 60mm long and expansion hold fasteners 12.5mm dia 40mm long all as specified and directed.

M&L for 6mm thick high pressutre, oceanic pre-primed, self embossed, non-asbestos fibre cement decorative board , water, termite and fire resistant for insulatrion and acoustic piurpose fixed or laiod/inserted to timber/GI/Aluminium framework with screws all as specified and directed.

MS TMT bars 8 to 10 mm dia and over, cut to length, bent to shape required, including cranking, bending etc and binding with and including mild steel wire (annealed) not less than 0.9mm dia as in reinfocement complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (dut not backing), removing rubish of the premises complete all as specified and as directed.

M&L 15 mm thick, screed bed or bedding layer of cement mortar 1:4, for laying floor finishes all as specified and directed.

M&L Non - skid Ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles all as specified and directed.

M&L Non - skid Ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles all as specified and directed.

M&L rendering 10mm thick in cement mortar (1:3) on fair faces of brick work or concrete surfaces as in vertical surfaces for laying tiles as directed all as specified and directed.

M&L Glazed ceramic tiles in vertical surface 350x 250x 7mm/ 450X 300X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match with the shade of tiles all as specified and directed.

S&F of 20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, win?dow-cills, cooking plat?forms and like in cement mortar (1:4) including point?ing in white cement (1:2) us?ing marble dust with admix?ture of pigment to match with shade of granite all as specified and directed.

M&L for rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified and directed.

Dismantling timber scantlings 40 Sq. cm and over in section and in any position in unframed work as directed and specified.

M&L 2nd class hardwood, scantlings, wrought, timber fixed, complete all as specified and directed.

Dismantling of timber fillets, rails, posts, rafters, purlins etc under 40 sqcm in section all as specified & directed.

S&F Second class hard wood plain fillets, square, rectangular or triangular in section, clean sawn, secured with nails, cross sectional area exc 6 and n.exc 13 Sqcm all as specified & directed.

M & L preparing new wood & wood based surfaces of any descriptions but not exc. 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer all as specified & directed.

S & F Aluminium Door closer hydrau?lically regulated, designation No. 1 universal type, suitable for door shutters up to 700 mm in width and of weight not more than 35 kg and fixed all as specified & directed.

Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed all as specified & directed.

Dismantling water tanks and removing to store Exc 500 & n.exc 1000 Ltrs all as specified & directed.

S&F Rotational moulded polye?thylene water storage tanks 1000 Ltrs capacity (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I all as specified & directed.

Dismantling water tanks and removing to store Exc 250 & n.exc 500 Ltrs all as specified & directed.

S&F Rotational moulded polye?thylene water storage tanks 500 Ltrs capacity (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I all as specified & directed.

S&F 15mm bore ball brass valves high pressure, with polythene float & fly nuts complete, screwed for iron pipe or brass ferrulecomplete all as specified and directed.

S&F 15mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed all as specified & directed.

S&F in repairs Vitreous china wash basin, white flat back, size 550mm x 400mm with brackets, excluding pillars cock 15mm bore CP, PVC connection of 450mm long including PVC (HDPE) 32mm bore waste pipe, brass couplings 32mm CP etc complete all as specified and directed.

S&F in repairs 15mm bore pillar taps, cast copper alloy, chromium plated, fancy type with capstan heads screwed down high pressure witgh or withoyut lettered Hot or Cold with long screwed shanks and fly nuts, screwed for iron pipe all as specified & directed.

S&F 15mm bore Brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixed all as specified & directed.

S&F in repairs, stop valves, 15mm bore cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed bhoth ends for iron pipe or for unions aall as specified & directed.

S&F in repairs 15mm bore PVC connection pipe 450mm longh with PTMT nuts at both ends all as specified & directed.

S&F in repairs, 10 Litres capacity PVC valveless syphonic action type, flushing cistern (ISI marked), low level with inlet. Ball valve, float bracket & flush pipe complete all as specified & directed.

S&F in repairs 15mm bore Bib Taps, Chromium plated cast copper alloy with crutch or butterfly handle, screwex for iron pipe or for brass ferrule and fixed all as specified & directed.

Dismantling 100mm bore, Cast iron or reinforced concrete drain pipes, jointed in cement mortar and taking out of trenches if required all as specified & directed.

S&F 110mm PVC (SWR) pipes single sockets, in any length with rubber ring joints, fixed to walls complete as specified and directed.

S&F PVC (SWR) pipes single sockets, in any length with rubber ring joints, laid in ground or floors 75mm dia complete as specified and directed.

S&F 110mm bore PVC (SWR) bends of any radius complete as specified and directed.

S&F in repairs, PVC (SWR) junction, single T equal or unequal 110mm bore all as specified & directed.

S&F in repairs, PVC (SWR) 75 mm dia, floor trap ,plain with grating including jointing to waste pipe with solvent cement and fixing in PCC 1:2:4 all as specified & directed.

S&F in repairs, 110mm bore PVC (SWR) vent cvowl all as specified & directed.

S&F in repairs Flush pipe of polyethylene of low or high density or PVC. 32 mm dia, for low level cistern omplete all as specified and as directed.

S&F in repairs 32mm dia Waste coupling of PTMT (half or full threaded) (Minimum weight 32mm?45gms/40mm-60 gms) complete all as specified and directed.

Demolition of brick work or stone/boulder masonry, built in cement morter including all quoins, arches, pillars etc complete all as specified and as directed

M & L old size brickwork with flyash bricks, straight or curved on plan to any radius in half brick thick walls, built in CM 1:4 all as specified & directed.

M&L Old size brickwork with fly ash bricks, straight or curved on plan exc 6m mean radius, built in CM 1:4 all as specified & directed.

Taking down cement plaster on brick or stone or concrete surfaces of wall etc , icluding raking out joints , hacking for key, scrubbing down with water etc all as specified & directed.

M&L for rendering 10mm thick on fair face of brick works or concrete surfaces of walls with CM (1:4) anf finished even and smooth without using extra cement all as specified & directed.

M&L for rendering 15mm thick on other than fair face of brick works or concrete surfaces of walls with CM (1:6) and finished even and smooth without using extra cement all as specified & directed.

M&L for rendering 5mm thick in ceilings of concrete surfaces with CM (1:3) and finished even and smooth without using extra cement all as specified & directed.

M&L for preparation of new plastered surfaces of ceiling and applying two coats of white wash over a coat over a coat of white primer etc all as specified & directed.

M&L for preparation newly plaster surfaces of wall, chajja facia etc and applying two coats of 100% premium Acrylic emulsion paint having VOC less than 50 gm/litre and UV resistant as per IS-15489=2004 alkali and fungal resistant exterior paint of required shed (company depot limited) with silicon additives 1/43 litres/10 Sqm over and including primer applied 0.90 litres/.10 sqm over new surfaces using Airless spray technology with maximum working pressure of 3300 PSI and capable of operating single spray gun with a maximum material hose length of 30 Mtr, the spray machine whould be of reputed manufacturer with pro guaeds technology and capability of tracking pressure and paint usage and certified by paint manufacturer and as mentioned in PS and acessories complete all as specified and directed.

M&L for Complete removal of existing treatment and treating from walls and applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, alkali & fungal resistance,dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new plastered surface even and smooth complete all as specified and directed

M&L for preparing of new plastered surfaces of walls & applying plaster of paris putty of 1 -2 mm thickness over plastered surface to prepare the surface even and smooth etc and applying two coats of oil bound distemper etc all as specified & directed.

M&L for preparation of old decorated plastered or unplastered sufaces of wall, cornices etc by brooming down or steel wire brushing, scrapping down, smoke soot, moulds, moos efflorescent and trading oil and greasy spots and applying two coat of cement base paint (white or tinned) complete all as specified and directed.

M&L for complete removal of old plastered surfaces of ceiling and applying three coats of white wash etc all as specified & directed.

Taking up or down 15 mm bore steel tubing and connections, including removal to store complete all as specified and directed.

Re-fixing 15mm bore old steel tubes,with all fittrings and fixed, to walls or laying in floors all as specified & directed.

S&F steel tubes, galvanised 15 mm bore, medium grade with all fittings & fixed complete to wall or laid in floors etc complete as specified and directed including taking down old one all as specified & directed.

Taking up or down 20 mm bore steel tubing and connections, including removal to store complete all as specified and directed.

Re-fixing 20mm bore old steel tubes,with all fittrings and fixed, to walls or laying in floors all as specified & directed.

S&F steel tubes, galvanised 20 mm bore, medium grade with all fittings & fixed complete to wall or laid in floors etc complete as specified and directed .

S&F in repairs curtain rails, mild steel, aluminium alloy chromium plated with fixing brackets, stops, rollers etc all as specified & directed.

Shower arm 15 mm size, 195mm long with bend of 45degree with flange of PTMT any colour.(Minimum weight 40gms) all as specified & directed.

M & L for Grating doom 100mm dia of PTMT (Minimum weight 25gms)all as specified & directed.

Shelf of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 300gms) all as specified & directed.

S&F in repairs, Towel rail 600mm long of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 190gms) all as specified & directed.

S&F in repairs sinks with drainage board made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm all as specified & directed.

S&F in repairs Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position all as specified & directed.

S&F in repairs vitreous china wash down water closet pan (Pedestal pattern) with seat cover white with 'P' or 'S' trap, including and flushing pipe etc complete including making good to disturbed surfaces of floor by filling with PCC 1:4:8 type D-2 to match with existing specifications as specified (excluding fixing bolts, flushing cistern and flush pipe) all as specified & directed.

Taking down carefully old unsv copper/aluminium point wiring (light, fan, socket or power) complete,including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets,sunken type box etc.and removing materials to store for keeping in safe custody for reuse at site or for taking credit and making good to disturbed surfaces of walls, floors etc with its original specification complete all as specified & directed.

Taking down carefully MCB DBs any type and size by unscrewing from main switch boards/cut out boxes and removing materials to store for keeping in safe custody for reuse at site or for taking credit including sealing the cable ends and making good disturbed surface of wall etc as per existing finishes all as specified & directed.

Taking down fan, sealing cable end, dismantling blades and removing fan and keeping it in MES store for safe custody and refixing it after repair all as specified & directed.

Material and labour for point wiring for the followings with 1.5 Sqmm single core, PVC FRLS insulated unsheathed, multistranded copper conductor drawn through and including PVC concealed including necessary accessories like bends, tees, PVC square and elbow etc fixed on wall/ceiling with 1.5 Sqmm PVC FRLS insulated unsheathed multi stranded copper conductor cable as earth conitinuity (green in colour) connected to common earth dolly suitable for modular sunken box with inner and outer cover for 01 module to 08 module for One light/exhaust fan point controlled by one, one way switch all as specified and directed. Note:-(1) Rate for Cutting, chieseling and making good the existing surface for complete concealed wiring is deemed to be included in quoted rate all as specified & directed. (2) Rate for Modular sunkan boxes, inner and outer cover measured and paid separately.

Description as per Ser item No.128 here-in-before but One 3 Pin 5 Amps socket out let point on independent board.

Description as per Ser item No.128 here-in-before but One bell point controlled by one push button switch.

Description as per Ser item No.128 here-in-before but one 3 pin socket outlet, 5 Amp same board complete all as specified and directed.

Description as per Ser item No.128 here-in-before but using 2.5 sqmm PVC FRLS insulated copper condutor wire for connecting 15A socket on independent board complete all as specified/directed.

Description as per Ser item No.132 here-in-before but with 4 sqmm complete all as specified & directed.

Supply and fixing of modular switch one way 6 amps 1 module 240 Volts all as specifed & directed.

Supply and fixing of modular socket outlet 2/3 pin 6 Amps 240 volts 2 module all as specifed & directed.

Supply & fixing of modular switch one way 16 Amps 1 module 240 Volts all as specifed & directed.

Supply and fixing of modular socket 6/16 Amps, 2/3 pin combined, 2 module all as specifed & directed.

S&F modular bell push switch 6A 1 module all all as specifed & directed.

Supply and fixing of modular metal flush box 1/2 module all as specifed & directed.

Supply and fixing of modular metal flush box 3 module all as specifed & directed.

Supply and fixing of modular metal flush box 4 module all as specifed & directed.

Supply and fixing of modular metal flush box 6 module all as specifed & directed.

Supply and fixing of modular white cover plate with frame 1 module all as specifed & directed.

Supply and fixing of modular white cover plate with frame 3 module all as specifed & directed.

Supply and fixing of modular white cover plate with frame 4 module all as specifed & directed.

Supply and fixing of modular white cover plate with frame 6 module all as specifed & directed.

Supply and fixing of surface mounting LED edgelit slim round downlighter made of PDC AL with minimum efficiency 100 LM/W with huge efficient LEDs and glare free opal diffuser, IP20 including all the accessories needed for its installation all as specifed & directed.

Supply and fixing of bell electric, ding dong type 240 Volts, single pole complete all as specified and directed.

Supply and fixing in repair of MCB Distribution board TPN double door 4 Way for mounting SPN/ SP/TPN/TP MCBs as Incoming / outgoing, factory made, confirming to IS, fabricated out of CRCA sheet , fitted with DIN channel, neutral link and suitable rated bus bar, DBs shall be semi glossy finished with epoxy polyester based powder paint sprayed and backed at high temperature, between powder paint process the sheet steel having to go through the anti rust conditioning in not less than seven tank process to ensure smooth finish and protection against corrosion atmosphere. The DBs shall be double door type with hinged door with locking arrangement. The DBs shall be of IP 43 - IK 09 with metal door all as specifed & directed.

Supply and fixing in repair of MCB Distribution board SPN 12 Way for mounting SPN/ SP MCBs as Incoming / outgoing, factory made, confirming to IS, fabricated out of CRCA sheet , fitted with DIN channel, neutral link and suitable rated bus bar, DBs shall be semi glossy finished with epoxy polyester based powder paint sprayed and backed at high temperature, between powder paint process the sheet steel having to go through the anti rust conditioning in not less than seven tank process to ensure smooth finish and protection against corrosion atmosphere. The DBs shall be double door type with hinged door with locking arrangement. The DBs shall be of IP 43 - IK 09 with metal door all as specifed & directed.

Supply & fixing in repair TPN 4 Pole, 415 V, fixed type,63 Amps with breaking capacity 16 KA with connection testing and commissioning including all the accessories needed for its installation all as specifed & directed.

Supply & fixing in repair of MCB SPN 32-40 Amps 'B' Series 10 KA 240 volts all as specifed & directed.

Supply & fixing in repair of MCB SP 6-32 Amps 'C' Series 10 KA, 240 volts all as specifed & directed.

M&L for Earthing complete with galvanised steel earth plate electrode 60×60cm.× 6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less'than 1.5 metres below normal ground level, connected to galvanised earth lead wire 4mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 5 connected to earthing test point all as specified or indicated including testing and commissioning all all as specifed & directed.

Supply & Fixing of ceiling fan step modular step regulator ,120W, 2 module all as specifed & directed.

Supply and fixing inverter type angular/batten holder PVC/Polycarbonate suitable for batten fittings including one LED inverter type Lamp of 9W all as specifed & directed.

Supply and fixing inverter type LED batten(1.2m) made of CRCA sheet housing with PC glossy diffuser duly prewired connection having a nominal system lumen output of 2000 lumen at a minimumsystem efficiency of 115 lumen per watt and total power consumption not more than 18/20 W iincluding driver. It has a rated system life time of 40000 burning hour at L70 and should have a colour temperature of 6500K, CR>80 , THD < 10 % and PF>0.95 all as specifed & directed.

S&F LED light fitting mirror type with high ouput diffuser 2 feet, 10 watts 220 volts AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable of suitable size all as specifed & directed.

Supply and fixing of LED wall bracket light aestheticallydesigned wall bracket light with B22d & E27 lamp holder with one lamp and with all the accessories required for its installation all as specifed & directed.

Supply and fixing of motion sensor 2 x 2 celing light including installation of all other accessories all as specifed & directed.

Supply and fixing of ceiling rose surface PVC/Polycarbonate, 65x50 mm two to three terminals all as specifed & directed.

Supply and fixing LED Bldg light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection all as specifed & directed.

S&F Bldg light bracket fabricated out of GI Tubing light grade 32 mm bore Bend to the shape as directed and of length 1.5 mtr complete with mounting MS clamp of flat iron size 40X5mm of suitable length 02 pairs incl nut bolts etc of suitable size, including taking down old corroded one all as specified and directed.

Material & labour for Sub main wiring with two runs of single core 6 Sqmm (Nominal Area) FRLS PVC insulated and unsheathed multi standed copper conductor cable LT 1100 volts grade drawn thorugh and including PVC conduit of adequate size fixed on surfafce of wall/ceiling with all necessary fittings and accessaries and 1 run of FRLS PVC insulated and unsheathed insulated single core cable with multi standered copper conductor of size 6 Sqmm as earth wire (green in colour) run through casing capping and connected common earth dolly including taking out the old sub main wiring two run of 6 Sqmm cable one run of casing capping and one run of 2.5 Sqmm earth continuity wire for connection to DBs/dolly shall be deemed to be included in this item and shall be measured as one run all as specifed & directed.

Taking down and Supply & Laying or Fixing or Passing through Pipe, XLPE insulated, Armoured, Electric Power UG Cable (Heavy Duty) with Aluminium Conductor, 1100 Volt Grade, Nominal Cross-Sectional Area 50 sqmm 4 core and Testing, including Brass Compression Cable Gland, Terminal Lug, etc including taking down all as specifed & directed.

Excavating in Trenches not exc. 1.50 mtr wide and not exc. 1.50 mtr in depth, Taking Out and Laying of Cables, etc. and getting out in Soft/ Loose Soil, all as specifed & directed.

Returning, Filling in, including Spreading, Levelling, Watering and Well Ramming in Layers not exc. 250mm in Soft/Loose Soil, complete all as specified and as directed.

Removing excavated Materials (Soils) not exc. 50.00 mtr and depositing where directed at a level not exc. 1.50 mtr above the Starting Point in Soil, complete all as specified and as directed.

M&L Sand Cushioning (dry) in Trenches for protection of UG Cables (below, above and around the UG Cable laid in Trenches) of 230mm Spread thick -ness and consolidated (punned) upto 180mm thickness, complete all as specified and as directed.

S&F Type-1 flat-1 size 250 x 150 x 40mm for cable protection cover well burnt, laid breadth-wise along the axis of Cable laid in Trenches over Sand Cushion laid for UG Cable Protection, complete all as specified and as directed.

Boring under without disturbing the top surface of the road for passing through GI protection pipe 50mm bore, not exceeding 10m in single length complete all as specified and as directed. Note: Necessary infrastructure required for boring shall be arranged by the contractor at his own cost.

Supply & fixing of Tubes, 'light grade' galvanised 50mm bore, with all fitting and fixed complete to walls and ceilings or laid in floors to run cables through them for its protection including all the accessories required, all as specifed & directed.

CHETIA CONSTRUCTION (BID ID -3411813)

FREEZCON (BID ID -3410239)