Reconstruction of Mattuthavani Bus Stand bus bay in madurai corporation

Amount

Demolition and Construction of New Bus Bay (4 Nos) Removing and Dismantling of the existing RCC roof slab PWD SOR 2024-25 -W-0035

Dismantling, clearing away and carefully stacking materials useful for re-use for any thickness of PCC. PWD SOR 2024-25 -W-0034

Earth work excavation for foundation in Hard stiff clay, stiff black cotton, hard red earth, shales murram, gravel,stoney earth and earth mixed with small size boulders SS.20B and Sand, silt or other loose soil, wet sand,or silt not under water, light black cotton soil, sandy loam ordinary soil and to full depth as may be directed except in hardrock requiring blasting inclusive of shoring shuttering and baling out water and cleaning and levelling the site etc.,complete 10 cum

Supplying and filling in foundation and basement with Crushed Stone Sand (M- Sand) in layers of not more than 15cm thick well rammed watered and compacted etc., complete complying with standard specification.

Plain Cement Concrete 1:5:10 (one part of cement, four part of Crushed Stone Sand (M- Sand) and eight part of coarse aggregates) using 40mm size ISS HBG metal including cost and conveyance of all materials to site and including for the mixing, laying and labour charges and all incidential charges such as water providing etc., complete as per standard specification

Centering for soffits of RCC slabs of plane surface like lintels, beams ,etc.,including strutting 3m high using mild steel sheets of size 90cm X 60cm X and B.G 10 stiffened with M.S angles of size 25mm X 25mm X 3mm laid over silver Oak (C.W) joists of size 10cm X 6.5cm (spaced at about 90cm c/c )and supported dy casurina props of 10cm to 13cm dia (spaced of 75cm C/C) complying with standard specification and directed - 10 m 2 (P & D)Data 38

Supplying and erecting centering for sides and soffits including necessary supports and strutting upto 3.29 M height for plane surfaces as detailed below in all floors with all cross bracings using Mild Steel sheets of size 90 x 60 cm and 10 BG stiffened with welded Mild Steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at abote 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete complying with the standard specificaiton. (Payment for centering shall be given after the concrete is laid) For plane surfaces such as vertical slab, side slabs of boxing, vertical drops, facia, vertical wall, etc. - Ground Floor

For plane surfaces such as vertical slab, side slabs of boxing, vertical drops, facia, vertical wall, etc.

Providing and laying in position Standardised Concrete Mix M-25 Grade in accordance with IS 456 - 2000 using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement contenet of 350Kg/ cum and maximum water cement ratio of 0.55 including admixture (Plasticiser / super plasticiser) in recommended proportions as per IS 9103 to accelerate, related setting of concrete, improve workability without imparing strength and durability with about (5.0cum), 7730Kg of 20mm machine crushed stone jelly and with about (3.3 cum), 5156kg of 10 - 12mm machine crushed stone jelly and with about (4.79cum) 7670 kg of Crushed Stone sand (M- Sand) but excluding cost of reinforcement grill and fabricating charges centering and shuttering but including laying, vibrating with mechanical vibrators, finishing, curing, etc and providing fixtures like fan clamps in the RCC floor / roof slabs wherever necessary without claiming extra cost etc., complete complying with standard specification and as directed by the departmental officers - The Coarse and Fine aggregates to be used should comply with the requiremnents of IS standards. Foundation and basement

Ground Floor

Suppling and fabricating and placing in position MS (or) R.T.S. bar for reinforcement to all RCC works as per the design given including cost of steel and binding wire also in all floors.

Brick work in Cement Mortar 1:5 (One cement ,five m sand) using best quality Fly ash bricks of size 23x11x7cm for foundation and basement including curing etc.,complete complying with standard specification.

Plain Cement Concrete 1:4:8 (one part of cement, four part of Crushed Stone Sand (M- Sand) and eight part of coarse aggregates) using 40mm size ISS HBG metal including cost and conveyance of all materials to site and including for the mixing, laying and labour charges and all incidential charges such as water providing etc., complete as per standard specification

Plastering with cement mortar 1:3 (One part of Cement and Three part of Plastering Sand (P- Sand)), 10mm thick in all floors including cost and conveyance of all materilas to site and labour charges etc,complete as per standard specifications

Plastering with cement mortar 1:5 (One part of Cement and Five part of Plastering Sand (P- Sand)) 12mm, thick in all floors including cost and conveyance of all materilas to site and labour charges etc,complete as per standard specifications

Painting two coats for Exterior surface with approved Exterior Plastic Emulsion paint approved quality and colour over a priming coat, including thorough scrapping, clean removal of dirt, etc complete and including necessary plaster of paris, putty, wherever required etc, complete as per standard specification.

Weathering Course with Concrete Broken Brick (S.I.No.278) & ( P & D) Data 54.Jelly 20mm gauge in pure slaked lime (no sand to be added) over roof slab,the proportion of brick jelly to lime being '32 to 12.5 well beated with wooden beaters for giving required slope and thickness as directed by the departmental officers etc., complete.-10 cum

Finishing the top of roof with one course of machine pressed tiles of size 200 mm x 200 mm x 20 mm of approved quality in Cement Mortar 1:3 (One part of Cement and Three part of Plastering Sand (P- Sand)), 12 mm thick mixed with water proofing compound conforming to ISS at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete

Providing & fixing PVC RAIN WATER DOWNFALL PIPE of the following dia with necessary T.W.Clamps Plugs, Shoes,Bemds, other clamps, screws nails etc.,complete complying with standard specification. The rate is inclusive of cost of removable iron gratings of appropriate size. The size of Teak Wood plugs used is 150X25mm in front & 200x75mm in rear (wall side) with a depth of 110mm. The pipe is to be fixed by means of "U" clamps at the centre of pipes to be fixed.110mm dia PVC Pipe [4 Kg/SqCm]

Paving the floor with kota stone slab of size 600 x 600 of 18 / 20mm (un-polished) in all floors laid in of cement mortor 1:3 (One part of Cement and Three part of Plastering Sand (P- Sand)), 20mm thick and pointed with colour cement neatly including polishing with polishing stone and oxalic acid etc., so as to perfectly smooth and glossy and including hire charges for polishing machine and power consumption charges etc. The kota stone slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on work, etc., complete as per standard speicification.

Electrical Items Wiring with 2 x 1.5 sq.mm. (22 / 0.3 ) PVC insulated single core unsheathed copper conductor cable of 1100V grade in suitable PVC rigid pipe on wall and ceiling with PVC accessories and with TW switch box and 5A FT switch with painting of suitable colour with continuous earth wire connection of 14 SWG TC wire for open PVC light point / fan point (for electronic regulator) (SD 16)

Wiring with 2 x 4 sq.mm. (56 / 0.3mm) PVC insulated SC unsheathed copper cable conductor cable of 1100V grade in suitable heavy gauge MS conduit pipe on wall and ceiling with MS accessories with 150mm x 100mm x 75mm MS switch box for 15A 3 pin non interlocking CS plug with painting of suitable colour with continuous earth wire connection by 14 SWG TC wire for open power plug point (SD 13)

Wiring with 2 x 1.5 sq.mm. (22 / 0.3 ) PVC insulated single core unsheathed copper conductor cable of 1100V grade in suitable heavy gauge MS conduit pipe on wall and ceiling with MS accessories in flush with wall with 150mm x 100mm x 75mm MS switch box with 3mm thick hylum sheet cover for 5A 3pin non interlocking CS plug with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour for concealed plug point (SD 12)

Supply and run of 2 of 4sqmm (56/0.3) PVC insulated SC unsheathed Cu.Conductor of 1100V Grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 14SWG TC wire and making good of the concealed portion with suitable colour (SD 45)

Supply and run of 2 of 6sqmm (84/0.3) PVC insulated SC unsheathed Cu.Conductor of 1100V Grade in suitable PVC rigid pipe concealed in wall and ceiling with contiinuous earth wire connection of 14SWG TC wire and making good of the concealed portion with suitable colour (SD 59)

Supply and providing cable end termination of 3-1/2 x 50 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete (SD 237)

Supply and fixing of brass cable gland for 3-1/2 x 35 sq.mm. PVC armoured LTUG cable with earth connection (SD 187)

Clamping of 3 1/2 x 50 sq.mm L.T UG Cabl on wall with MS Clamp

Supply and providing cable end termination of 3-1/2 x 50 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete SD 237

Supply and fixing of horizontal type 4 way triple pole neutral MCB distribution boarding sheet steel enclosure double door (metal) with 40 A 4 pole MCB isolateras incoming and 12Nos .6A to 32 A SP MCB as outgoing inflush with all and making good of the concealed portion with earthconnection.The MCBDB and MCB's should be with the ISImark (like standard make) SD157

Supply and run of 1 of No.8 SWG GI wire for earth connection (SD 74)

Supply and run of 25mm x 6mm tinned copper flat with necessary clamps / supports on wall / floor / ground for earthconnection (SD 77)

Earthing as per P.W.D standard with an earth electrode of 2 Mtr. Class 'B' GI pipe of dia not less than 32mm complete with necessary masonry work (SD-234)

Cost of supply of 18w 4 feet LED fitting with tube light complete set PWD - SOR - 2024-25 - Vol 1 -M-1274

Storm Water Drain Dismantling removal of cut stone slabs & RCC cover slab

Dismantling, clearing away and carefully stacking materials useful for re-use for any thickness of PCC. PWD SOR 2024-25 -W-0034

Cement Concrete 1:4:8 (one part of cement, four part of Crushed Stone Sand (M- Sand) and eight part of coarse aggregates) using 40mm size ISS HBG metal including cost and conveyance of all materials to site and including for the mixing, laying and labour charges and all incidential charges such as water providing etc., complete as per standard specification

Supplying and erecting steel centering including necessary supports for plane surfaces for Reinforced Cement Concrete works such as column footings, column pedestals, plinth beams, grade beams, staircase steps, etc. which require only nominal strutting using mild steel sheets of size 90cm x 60cm and 10 BG stiffened with welded mild steel angles of size 25mm x 25mm x 3 mm for boarding, laid over silver oak joists of size 10cm x 6.5cm spaced at about 75cm centre to centre or at suitable intervals etc. complete in all floors complying with standard specifcation. (Payment for centering shall be given after the concrete is laid) (For DRAIN)

Providing and laying in position ,Standardised Concrete Mix M-20 Grade in accordance with IS :456-2000,using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement content of 325 kg/m3 and m,aximum water cement ration of 0.55, including admixture (Plasticiser/Superplasticier) in recommended proportions as per IS:9103 to accelerate ,retard setting of concrete,improve workability without impairing strength and durability with about (5.0 cum) 7730 kg of 20 mm machine crushed stone jelly and with about (3.3 cum) 5156 kg of 10-12mm machine crushed stone jelly and with about (4.79 cum) 7670 kg of sand, nut excluding cost of reinforcement grill and fabricating charges,centering and shuttering and also including laying,vibrating with mechanical vibrators,finishing,curing,etc and providing complying with standard specification and as directed by the departmental officers. The coarse and fine aggregates to be used should comply with the requirements of IS Standrands.(No separate payment will be made by the Department for the excess usage of materials)

Suppling and fabricating and placing in position MS (or) R.T.S. bar for reinforcement to all RCC works as per the design given including cost of steel and binding wire also in all floors.

Road Work Dismantling, clearing away and carefully stacking materials useful for reuse for any thickness for PCC

Providing and laying in position ,Standardised Concrete Mix M-20 Grade in accordance with IS :456-2000,using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement content of 325 kg/m3 and m,aximum water cement ration of 0.55, including admixture (Plasticiser/Superplasticier) in recommended proportions as per IS:9103 to accelerate ,retard setting of concrete,improve workability without impairing strength and durability with about (5.0 cum) 7730 kg of 20 mm machine crushed stone jelly and with about (3.3 cum) 5156 kg of 10-12mm machine crushed stone jelly and with about (4.79 cum) 7670 kg of sand, nut excluding cost of reinforcement grill and fabricating charges,centering and shuttering and also including laying,vibrating with mechanical vibrators,finishing,curing,etc and providing complying with standard specification and as directed by the departmental officers. The coarse and fine aggregates to be used should comply with the requirements of IS Standrands.(No separate payment will be made by the Department for the excess usage of materials)

Toilet Abstract Dismantling, clearing away and carefully stacking materials useful for reuse for any thickness of Brick / stone masonry in Cement mortar walls under 3m high in all floors etc.,

Dismantling, clearing away and carefully stacking materials useful for re-use for any thickness of PCC.

Plain Cement Concrete 1:4:8 (one part of cement, four part of Crushed Stone Sand (M- Sand) and eight part of coarse aggregates) using 40mm size ISS HBG metal including cost and conveyance of all materials to site and including for the mixing, laying and labour charges and all incidential charges such as water providing etc., complete as per standard specification

Supplying and filling in foundation and basement with Crushed Stone Sand (M- Sand) in layers of not more than 15cm thick well rammed watered and compacted etc., complete complying with standard specification.

Brick work in cement mortar 1:5(one cement and five sand) using best quality of Fly Ash bricks of size 230x110x70mm etc.,complete complying with standard specification..(Masonry projection wherever necessary for obtaining required elevation shall be done without any extra cost) For Foundation and basement

For superstructure in Ground floor

Brick partition wall using best quality of Fly Ash bricks of size 230x110x70mm in cement mortar 1:3 (one cement and three sand) of the following thickness including supplying and fixing hoop iron reinforcement if considered necessary by the departmental officers as directed complying with standard specification. For Ground floor

Supplying and erecting,centering for sides and soffits including supports and strutting up to 3.29m. High for plane surfaces such as RCC slabs Rectangular beams,Tee(or)Ell beams,lintels,Bed Block, slabs,landing beam,canopy side slab,or boxing(or) vertical slabs,rectangular(or)square(or)round columns etc., as detailed below with all cross bracing using M.S. Sheets of size 90cmx60cm and B.G.10 stiffened with welded M.S.Angle of size 25mmx25mmx3mm for boarding laid over silver oak joists of size 10cmx6.5cm.,spaced at about 90cm centre to centre and supported by casuarina props 10cm to 13 cm dia. spaced at 75cm centre to centre and as directed by the drpartmental officers etc., complete complying with standard specification. For plane surfaces such as RCC floor slab, rectangular square Tee or El beam, lintel, bed block staircase, waist and landing slabss, landing beam, canopy etc.,

Providing and laying in position standardised concrete mix M20 grade in accordance with IS 456/ 2000 using 20mm and down graded hard broken granite stone jelly for all RCC items of work with minimum cement concrete of 325 kg/m3 and maximum water cement ratio of 0.55, including admixture (Plasticiser / Super Plasiciser @ 0.60% of cement) in recomended proportion as per IS 9103 to accelarate retard setting of concrete, improve workability without imparing strenghth and durability with about (5 cum) 7730 kg of 20mm machine crushed stone jelly and with about (3.30 cum) 5156 kg of 10mm -12mm machine crushed stone jelly and with about (4.79 cum.) 7670 kg of sand but excluding.. For superstructure in Ground floor

Suppling and fabricating and placing in position steek reinforcement using mild steel or ribbed steel tor steel rods for all RCC works as per the design given including cost of steel and binding wire shall be supplied by the contractor in all floors complying with standard specification

Dadooing the walls with best quality and approved colour glazed tiles of size 300mmx450mmx8mm and set in cement mortar 1:2 (one cement and two sand) and pointing with colour cement neatly in all floors etc., complete as directed by the departmental officers complying with standard specification.(The tiles should be got approved by the Executive Engineer before use on work)

Flooring with self designed ceramic tiles of size 305x305x6mm laid over 20mm.thick cement mortar 1:3 (one cement and three sand) base mortar over the existing slab/floor including cutting the tiles to the required size with special cutter wherever necessary laying in position and pointing with white cement mixed with colouring

Paving the floor with best approved quality fine polished Granite Stone Slabs of size 1200 x 600 of 18 / 20mm thick of Synthetic Grey, Paradise and similar varieties with machine cut edges laid over a cement mortar bed of 20mm thick using cement mortar 1:3 (One cement and three sand) fixing the slabs with required cement slurry and laid in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with mathcing colouring pigments etc., The granite stone slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on work, etc., complete as per standard speicification.

Supplying and fixing in position 40 mm dia best approved quality "B" class GI pipe for hand rails welded ngidly with the M.S. balustiade including cutting the G.I. Pipe to required length bending at the flight turning, welding neatly the GI pippe at the joints etc., complete complying with standard specification.

Providing and fixing casement doors fabricated from un-plasticized polyvinyl chloride (uPVC) sections Profiles: The profiles should be three chamber system which provides high insulation properties with outer frame 60mm x 55mm with an outer wall thickness of 2.4mm. The window unit should be designed with all corner joints mitred and fusion welded. Windows should be steel reinforced with 25 x 24 x 25mm steel reinforcement with a thickness of 1mm to have dimensional stability. The sash should be of 60 x 102mm. The mullion should be of 60 x 74mm. The profiles should have co-extruded seals.Hardware: All the hardware like friction stays, handles should be screwed with self tapping screws. The handles, locks should be designed so that they cannot be released from outside.Glazing: The window system should be glazed with 5mm plain float glass / 6mm bison lam. Installation: The profiles should be cut to length and welded 45 degrees. The window should be designed such that the water drainage does not pass through the reinforcement chamber. The window system should be fixed directly to the plastered brick wall using self expanding nylon plug and driving ms electroplated screws into plug

Solid FRP door shutters 19 Gauge 19mm.MS.sq.tubes for styles and outer M.S.sq.tubes for top, lock and bottom rails. The Steel tubes shall be covered with 5mm.thickframes. 15mm.solid PVC.sheets. Shutter using 5mm.thick soilid PVC.sheets for panelling shall rigidly fixed in position including necessary furniture and fittings.The over all size of styles shall 50mm thick The over all size of top rail,Lock rail and bottom rail shall be 75x30mm. The over all size of frames shall be 50x45mm, with suitable rabate for housing the shutter

Supplying Fabricating and Fixing in positionof UPVC Ventilator ( size 0.60m x 1.80m ) of outer frame using rectangular box section of with the following shutter frame and necessary such as rubber beading, furniture fittings including cost of materials and labour and power consumption charges required for fabrication including necessary clipping dismantling and making necessary holes in RCC columns,Beams, Masonry with power drill to the required extent and redoing the same to the original condition after fixing etc., complete.

Supplying and fixing MS grills for Doors and Windows and Ventilators of approved design and as directed by the departmental officers including cost of MS grill, labour charges and cost of one coat of red oxide primer with labour charges for priming coat etc., complete complying with standard specificaitions.

Manufacturing, supplying and fixing Precast Reinforced Cement Concrete slabs of following thickness in RCC 1:2:4 (one cement, two sand and four aggregates), using following HBGS jelly excluding cost of reinforcement steel in position but including cost of moulding charges, casting of slab, finishing, curing and fixing in position in all floors etc., complete complying with standard specification and as directed

Plastering with cement mortar 1:5 (one cement and five sand) 12mm thick in all floors celling cell etc., complete combined with standard specification

Special ceiling Plastering with cement mortar 1:3 (one cement and threesand) 10mm thick.,in all floors celling cell etc.,complete complying with standard specification.

Painting two coats over new iron works such as steel doors, windows, ventilators, window bars,balustrates etc., with best approved first quality synthetic enamel paint oe approved colour over the existing red oxide priming coat in all floors. The rate is inclusive of all materials,brushes and scaffolding charges etc., complete complying with standard specification. (Paints should be got approved by the Executive Engineer before use on work)

Painting the walls with Two coats exterior emulsion painting over one coat of primer as instructud by the departmental officers including preparation of surface curing etc., complete in all floors including cost of priming coat etc., with best approved first quality Cement Paint approved colour over the priming coat in all floors. complying with specification .(The make, quality and colour of paint should be got approved by the Executive Engineer before use on work)

Supplying and fixing in position white glazed earthernware wash hand basin of size 550x400mm with required specials including cost of specials, labour charges etc complete.

Supplying and fixing in position by means of 75mm long and 6.50mm dia, counter sunk bolt and nuts embedded in the floor with rubber or fibre washers, best quality and approved make white glazed earthernware Europeon water closset with 100mm P or S trap, seat and double flabbed rigid PVC seat cover with chromium plated hinges including suplying and fixing white glazed PVC low level flushing tank of ten litre capacity with all internal fittings with a pair of cast iron brackets and with all fittings such as 15mm dia nylon connection, 15mm dia GM wheel valve, 15mm dia brass nipple including labour charges for fixing the flushing tank on wall with TW plugs and screws, giving water supply connection, painting the CI brackets with two coats of best approved quality synthetic enamel paint over a coat of red oxide primer redoing the disturbed masonry and flooring to original condition etc complete complying with standard specification.

S/F in position of Indian Make White/Colour glazed earthen ware lipped mouth Flat Back Urinal of best approved quality with G.I.Pipe connection to suitable length,32mm bell mouthed P.V.C connection ,15mm dia G.M.Wheel valve,fixing the urinal to the wall in position with necessary T.W.plugs ,clamps,screws, shellac etc.,including dismantling masonry if necessary and redoing the same to original condition ,fixing the 15mm dia. G.I.pipe connection and wheel valve ,painting the pipe with two coats of approved paint over one coat of primer and checked without any leakage complete, complying with standard specifications. - White Colour

Supplying and fixing in position best approved quality PVC Nahini trap of 100x75mm size with necessary specials etc complete.

Supplying, laying and jointing UPVC Pipe (Un-Plasticized Polyvinyl Chloride) UPVC used for residential and home applications, water pressure in residential areas do not normally exceed the maximum tolerance. (Schedule-40) of approved quality and best variety conforming to BIS of the following dia including cutting, threading and fixing PVC specials using PVC adhesives (but excluding cost of such specials) and fixing into wall with teak wood plugs, PVC clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges upto 4 metre height above ground level, etc., complete complying with standard specifications. The PVC pipes shall be got approved by Executive Engineer before use on works.External Water Supply Arrangements (Above Ground Level) 20mm dia UPVC Pipe External Water supply

25mm dia UPVC Pipe External Water supply

32mm dia UPVC Pipe External Water supply

Supplying, laying and jointing UPVC Pipe (Un-Plasticized Polyvinyl Chloride) UPVC used for residential and home applications, water pressure in residential areas do not normally exceed the maximum tolerance. (Schedule-40) of approved quality and best variety conforming to BIS of the following dia including cutting, threading and fixing PVC specials using PVC adhesives (but excluding cost of such specials) and fixing into wall with teak wood plugs, PVC clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges upto 4 metre height above ground level, etc., complete complying with standard specifications. The PVC pipes shall be got approved by Executive Engineer before use on works.External Water Supply Arrangements (Below Ground Level) 32mm dia UPVC Pipe External Water supply

Supplying and fixing in position of the following best GI Union of approved quality conforming to ISS and providing leak proof jionts withGI adhesives etc., including fixing to walls with necessary Teak wood Plug Screws etc. and giving connection to the GI Pipes dismantling the brick masonry or floor / roof slab and redoing the disturbed portion to original condition etc., complete complying with standard specifications. 20mm dia GI Union

25mm dia GI Union

32mm dia GI Union

Supplying UPVC Specials (with working pressure 10 kg. / sq.cm.) in water supply arrangements (both in internal and external water supply arrangements 20mm dia UPVC PVC Elbow

25mm dia UPVC PVC Elbow

32mm dia UPVC PVC Elbow

20mm dia UPVC PVC Tee

25mm dia UPVC PVC Tee

32mm dia UPVC PVC Tee

32mm x 25mm dia UPVC PVC Reducer

25mm x 20mm dia UPVC PVC Reducer

20mm x 15mm dia UPVC PVC Reducer

32mm dia UPVC PVC Hex Nipple

25mm dia UPVC PVC Hex Nipple

Supplyingand fixing in position first and approved vareity with ISI mark gunmetal gate valve/wheel (heavy type) of the following dia of cuting and threading etc., (The Gun metal gate value/ wheel value should be got approved by the E.E., before use on work) 25mm dia Gate valve

32mm dia Gate valve

Supplying and fixing 15mm dia CP tap approved quality with ISI mark etc., Complete (The C.P brass screw tap got approved by the E.E before use on work)

Supplying and fixing best quality of coloured porcelain soap dish of size 150x150x50mm flush with the wall including dismantling the wall and the same ton etc., complete complying with standard specification

Supplying and fixing in position bevelled edge mirror of size 600x450mm with specials etc complete.

Supplying and fixing in position CP Towel rail 600mm long and 20mm dia with brackets of same materrial including cost of TW plugs and CP screws etc complete.

Supplying and fixing in position best quality PVC soil / waste pipes of various dia having 6 kg / sq.cm. pressure BIS mark and providing leak proof joints using PVC adhesives including fixing to the wall with special PVC / MS clamp, teak wood plugs, brass screws, etc., and making connection to all sanitary fittings, dismantling masonry / RCC works wherever found necessary and making the good dismantled portion to the original condition, including testing for any leakages, etc., complete complying with standard specifications. (The PVC pipes should be got approved by the Executive Engineer before use on works). The rate for earth work excavation will be measured and paid separately in the cases where the pipe lines are proposed to laid (Above Ground Level) 90mm dia PVC Pipe

110mm dia PVC Pipe

Supplying and fixing in position of the following best PVC Specials of approved quality ( 6Kg/m2) conforming to ISS and providing leak proof jionts with PVC adhesives etc., including fixing to walls with necessary Teak wood Plug Screws etc. and giving connection to the PVC Pipes dismantling the brick masonry or floor / roof slab and redoing the disturbed portion to original condition etc., 110mm dia PVC elbow

90 mm dia PVC elbow

110 mm dia PVC elbow Door

90 mm dia PVC door elbow

110 mm dia PVC Bend

Supply and providing 1000 litres capacity Priming Tank made up of PVC. Make: SINTEX / EQUIVALENT PWD - SOR - 2024-25 - M-0821

For Electrical Items Supply and fixing of single box type 4'40W fluorescent fitting complete with copper choke and condensor with conduit pipe suspension from the ceiling with PVC unsheathed FRLS copper leads from terminals to the fitting with tube SD 89

Wiring with 2 x1.5 sq.mm. PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A one way module switch with module front plate with continuous earth wire connection of 1.5 sq.mm copper wire and making good of the concealed portion with suitable colour for Concealed PVC Light point / fan point (for electronic regulator) (6 points / Coil) Higher End SD 283

Supply and fixing of 300mm (12") sweep (light duty) AC exhaust fan complete without provision of hole in the wall SD 115

Supply and fixing of louvers shutters arrangements for 300mm (12") sweep (light duty) AC exhaust fan SD 120

Supply and fixing of 1 no.6/16A two module socket , 1 no. 16A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Higher End SD 401

Supply and Run of 2 of 4 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with continuous earth wire connection by 4 sq.mm. PVC insulated SC unsheathed FRLS copper wire and making good of the concealed portion. SD 351

Pressed Tile Replacement in Main Terminal Building Dismantling Pressed Tiles :(PWD SOR Pg no-28,W-0037)

Finishing the top of roof with one course of machine pressed tiles of size 200 mm x 200 mm x 20 mm of approved quality in Cement Mortar 1:3 (One part of Cement and Three part of Plastering Sand (P- Sand)), 12 mm thick mixed with water proofing compound conforming to ISS at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete

Painting Existing Building Painting the walls with two coats exterior emulsion painting over one coat of primer

Plastering with cement mortar 1:5 (one cement and five sand) 12mm thick in all floors celling cell etc., complete combined with standard specification

ACP Cladding to Main Terminal Building Providing and fixing of Aluminium Composite Panel (ACP) 4 sided having 50 x 25 x .50mm frame work vertical and horizontals out of specially designed extruded ctions ithstand wind pressure of 180 Kg/sq.m and fabricated fixed at all level evation and eights. The extruded section cutting and fixing required space xtruded section shall be of 063and alloy of BSH 9 confirming T is – 63400 rate shall ncluded to fix the main frame with necessary clamps, fasteners, bolt nuts etc. The main frame of extruded section shall be of 22843 & 22739 (H9) grade onforming to BS 4174 (or) IS 8147. Rate shall included 4mm thick ACP sheet (0.25 + 3.5 + 0.25) alstrong or equivalent fixing with pacer tape and the ACP sheet bounded with pecial type structural sealant of dow orning 789 or equivalent in dust free conditions the gaps between ACP sheet to be filed with hether sealant and backer rod or 12mm foam sheet to ensure water and air tightness in all complete complying with standard specification as directed by the departmental fficer

WPC Panelling PANNELLING ON WALL & CEILINGS WITH WPC PANNELS OF SIZE 8' X4' and 18mm Thickness.Providing and fixing panelling on wall & ceilings with WPC(Wood Polymer Composite) of approved make & approved shade in approved pattern as directed by the Engineer Inchrage. Rates shall be inclusive of all hardware fittings and fixtures as required to fix the same on the wall and ceilings including corner beading and fastners

UGSS Pipe Line and Manhole Earth work excavation for foundation in Hard stiff clay, stiff black cotton, hard red earth, shales murram, gravel,stoney earth and earth mixed with small size boulders SS.20B and Sand, silt or other loose soil, wet sand,or silt not under water, light black cotton soil, sandy loam ordinary soil and to full depth as may be directed except in hardrock requiring blasting inclusive of shoring shuttering and baling out water and cleaning and levelling the site etc.,complete 10 cum

Supply and Delivery RCC non pressure spun pipe with socket and spigot ends as per IS 458/2003 manufactured with sulphate resistant cement with 12 mm HI -alumina lining with rubber ring joints. (SOR VOL-2 WD-M1035)

Lowering RCC pipes and specials into the trenches and laying to proper grade and alignment (SOR VOL-2 WD-W0366)

Jointing RCC pipes with cement using necessary collars including the cost of jointing materials. (SOR VOL-2 WD-W0383)

Cutting R.C.C. Pipes true to axis and finishing the ends complete (SOR VOL-2 WD-W0524)

Construction of manholes using sulphate resistant cement at various depths to invert including earth work excavation asperSS20B, laying cement concrete in C.M.1:3:6 using 40mm B.G. jelly for foundation, sinking well kerb below G.L. for 4.5m depth and above, pumping, timbering charges for 2.5m depth and above, stock brick work in C.M.1:3, for 23cm thick wall and over 23cm thick wall, plastering interior with C.M.1:3, 20mm thick and exterior with C.M.1:3, 12mm thick, laying plain cement concrete 1:3:6 using 12.0mm to 20mm B.G. jelly fixing the frame, providing C.I. steps, manhole cover and frame etc. complete for the following sizes for each manhole (As per the type design drawing for manholes).(SOR CORP BUIL 23-24 PAGE-93 SNO-144) 0.50M DEPTH

1.00M DEPTH

1.50M DEPTH

Refilling charges with excavated soil Other than Sand (SOR CORP BUIL 23-24 PAGE-NO 6)

Add GST 18%

SRI KAMAACHI ENGINEERING CONTRACTS (BID ID -1418555)