ADDN/ ALTN TO GDCC/ IPSS SETUP AND PROVN OF TIMER FOR SECURITY LIGHTS AT AF STN AWANTIPUR

Amount

B/R PORTION

Demolition of stone/brick masonry built in cement mortar incl quoins, arches, etc but exceeding ashlar facing dressed stone Work etc complete all as specified and directed

M&L for Brick work with sub class 'B' bricks, straight or curved on plan exc 6m mean radius in cement mortar 1:6, complete all as specified and directed

M&L brick work with sub class ‘B’ bricks (locally available best quality) straight or curved on plan to radius half brick wall built in CM (1:6) complete all as specified and directed.

Rendering 10mm thick plaster on brick work or concrete surface in cement mortar (1:4), finished even and smooth without using extra cement including Taking down cement plaster on brick or stone walls, etc including raking out joints, hacking for key, scrubbing down with water etc.complete all as specified and as directed

M & L Rendering 15 mm thick plaster on fair faces of brick work or concrete surfaces in CM 1:4 on wall surfaces, finishing the surface even and smooth without using extra Cement complete all as specified. Note:- Integral water proofing compound shall be measured and paid for separately.

Preparing new plastered or un-plastered surfaces of walls and applying two coats Acrylic exterier emulsion paint in camouflaging (Disruptive) pattern (Green, Grey & Brown colour) over a coat of acrylic primer complete all as specified and directed. (Make:Asian/Berger/Nerolac/ICI/Shalimar/Garware/Johnson).

Preparation of newly or plastered or un-plastered surfaces of walls and applying two coat of Acrylic washable distemper over a coat of primer after applying 3mm thick wall care putty in two layer on prepared suface complete all as specified and directed.

Demolition of cement concrete to ground floor(unreinforced) and paving n.exc 15cm thickness (below or above ground level) and removing rubbish of out side MOD land, complete all as specified and directed.

M&L for cement concrete 1:3:6 type C-2 (40mm graded aggregate) 25 mm thick for sub-base in sub floor sub base, floor and paving etc cement complete all as specifiied and directed.

Demolition for floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises, complete all specified and directed.

M&L coloured/printed ceramic tiles 7 to 8 mm thick area of each tiles exc 0.18 sqm but not exc 0.38 sqm, laid in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile laid over and including 15mm thick bedding layer in cement mortar (1:6) including necessary cutting and waste as per site requirement complete all as specified and directed by Engineer-in-Charge.

All as per serial item no 12 above but on vertical surfaces such as skirting incl including 10mm thick rendering in cement mortar 1:4 rough finish to receive the tiles complete all as specified and directed.

M&L coloured/printed non skid ceramic tiles 7 to 8 mm thick (squre/rectangular) area of each tile exc 0.11 but not exc 0.16 sqm laid in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the white tile laid over and including 15mm thick bedding layer in cement mortar (1:6) including necessary cutting and waste as per site requirement, complete all specified and directed.

M&L for glazed coloured ceramic tiles, first quality (or approved class, colour and design/shade) of 450X 350X 7mm/450x300x7mm thick in vertical surfaces, as in dado/skirting etc set & jointed in neat cement slurry & pointed in coloured cement to match with coloured tiles, over and including 10mm thick rendering in cement mortar 1:4 rough finish to receive the tiles complete all as specified and directed.

Dismantling of wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/ slabs/ blankets on any description, any thickness, including cover fillets.

Providing and Fixing False ceiling with semi perforated 12mm thick micro GRG false ceiling tiles at all heights with GRG (Glass fibre reinforced gypsum) false ceiling tiles of size 595 x 595mm of approvedtexture , design and patterns having moisture content less then 2%humidity resistance of 99%, NRCO. 52 to 0.75 as per is 8225: 987,noncombustible as per BS476 (part 4) -970 and light reflectance of85% (Minimum)to be laid in true horizontal lavel supended oninterlocking metalsT-Grid of hot dipped galvanised iron section of0.33mm thick (Galvanised @ 120 gms per Sqm including both sides )comprising of main-T runners of size 15 x 32mm of length 3000mm,cross - T of size 15 x 32mm of length 1200mm and secondaryintermediate cross- T of size 15 x 32mm of length 600mm to from gridmodule of size 600 x 600mm, suspended from ceiling using galvanisedmild steel items (Galvanizing 80 gms per sqm) i.e. 50mm long, 8mmouter diameter M-6 dash fasteners, 6mm dia fully threaded hanger rodupto 1000mm length and L- Shape level adjuster of size 85 x 25 x2mm.Galvanised iron perimeter wall angle of size 24x24x0.40 of length3000mm to be fixed on prephery wall / partition with the help of plasticrawl plugs at 450mm centre to centre and 40mm long dry wall woodscrews. The work shall be carried out as per specifications, drawing and as per direction of the Engr-In-Charge.

S&F PVC SHEET WALL PANELLING of thickness 5mm consisting of panels of desired size stuck on inner frame work of 50mm wide strips of 5mm thick prelam PVC sheet. The strips should two PVC strips. The PVC strip shall be fixed to the wall using 65mm long M.S screws through the groove in the strip by using PVC fasteners. The distance between two screws shall not be more than 200mm. A groove of 2mm may be left at the joint of two panels for aesthetic looks. The exact size of the panel and correspondingly of the grid may vary depending on the size of the wall. Optionally a U Channel at top, bottom and side edges and strips of 5mm thick PVC sheet of width 75mm feathered at the edges shall be stuck at the places where two panels are joined, using solvent cement complete all as specified and directed ( Note- Including all necessary fittings and scaffolding for heighted site)

Supply and fixing of Toughened glass of 12mm as in hinged doors, partitions automatic doors and similar work including cutting to shape, drilling holes required (toughened glass as per the design directed by Engineer-in-Charge) of comprising of the including all connecting accessories ie joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges etc. complete all as specified

S&F in repair PVC flushing cistern 10 ltr capacity white with all internal fittings including brackets PVC connection 45cm long including nut and PVC washer at both ends including 32mm bore PVC long bend flush pipe 90cm long complete all as specified and directed.

S & F Vitreous china wash hand basin coloured, flat back type of size 550mm x 400mm including waste pipe & plug, porcelain stopper, 32mm dia PVC waste pipe with CP brass coupling and set of bracket complete all as specified and directed.

S&F in repair Vitreous China wash down water closet (pedestal pattern), White/coloured including traps, connection to drain or outgoing pipe, flushing pipe, anti-syphonage pipe complete including fittings, PVC coloured seat cover and chromium plated jet including PVC connection, fixed complete including demolition of old unserviceable WC and provision of plain cement concrete M-15, type B-I, using 20mm graded crushed stone aggregate, fixed in repairs complete all as specified and directed.

S&F in repair Vitreous China urinals of minimum size 580x380x350 mm, crystal white, HALF STALL URINAL, with 32 mm bore waste fittings, brass, chromium plated with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including spreader, 60mm long brass screws, pointing around urinal back in cement with brackets, flush pipe, trap, grating and Union for discharge pipe. (Including fixing supply pipe to flushing cistern, trap and waste pipe) complete all as specified and directed.

S&F 500 litre capacity rotational moulded polyethylene water storage tank (cylindrical vertical double layered with closed top) duly provided with necessary fittings/ fixtures for connecting inlet, outlet, washout and overflow pipes; hoisted and fixed in position.Make-Syntex/Rotex/Polycon

Taking down chowkhats of frames of any description n.exc 1.50 sqm with shutters (without taking off shutters from the frames) and making good disturbed portion complete all as specified and directed.

S&F for solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS Square tube supply and fixing as specification and drawing.

S&F of factory Made Solid panel PVC door shutter, 28 to 30mm thick (stiles) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded and wood grain printed PVC sheet used instead of Plain colour PVC sheet & 5mm thick x15mm wide PVC sheet beading used inside stiles and rails and decorative PVC beading of 10mm x 10mm (900 ) used instead of exposed portion of PVC sheet beading plain colour PVC sheets for top rail & bottom rail, paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and jointed together with solvent cement, supplying and fixing in the frame at site as per specification & drawing.

S&F Anodised aluminum frame for doors, windows and ventilator with one or more rebates including joining cleat for fixing etc. complete all as specified

S&F anodised aluminum door shutters, aluminum section weighing 1.10kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified

M&L for 12 mm prelaminated particle board both side decorative, fixed with aluminum beading and rubber neoprene packing to aluminum frame

S&F 125 mm long stainless steel butt hinges medium weight with stainless steel screw complete.

S&F Aluminum alloy anodised barrel tower bolts of extruded section 150 mm long and fixed complete.

S&F extruded aluminum alloy handles of size 125mm fabricated type anodised complete.

Anodised aluminum window and ventilator shutters, fixed type without sash bars, aluminum sections weighing of 0.55 kg/RM including fixed with aluminum beading, silicon lining and gaskets, necessary joining cleats, glazing clips, rubber packing, anodised aluminum snap beading, screws etc complete all as specified and directed

S&F of galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm fixed with tinned tacks, or galvanized wire staples all as specified & directed.

4.8 mm thick sheet glass, ground or obscured or frosted/ tinted and glazing with oil putty or fixed with bead/glazing pins in squares of exe 0.5 sqm in each pane all as specified and directed.

S&F 15 mm dia medium grade galvanised with all fittings and fixed complete to walls and ceilings or laid in floors.

Cutting chases, pinning for concealed water tubing and making good to facing where required and pointing in cement mortar 1:3 ,cutting exc 10cm but n.exc 20cm girth all as specified and as directed.

S&F in repair 15mm bore gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe complete all as specified and directed.

S&F in repair brass chromium plated tubular towel rails 20mm dia D type 60cm long between flanges with chromium plated bracket and fixed all as directed.

S&F in repair 15 mm bore CP Bib tap cast copper alloy fancy type crutch or butterfly handles screwed down for iron or for brass ferrule complete.

S&F in repair stop valve/angle valve, fancy type, chromium plated, cast copper alloy screwed down, high pressure, with crutch or butterfly handle of 15mm dia. Screwed both ends for iron pipe or for unions and fixed. all as specified & directed.

S&F in repair Brass CP central hole wash basin mixer for hot & cold for 15mm dia complete fixed to connection as specified and directed.

S&F PVC (SWR) pipes single socketed,75mm bore, in any length with rubber ring joints fixed to wall and floor, complete all as specified and directed.

PVC (SWR) 75mm bore (dia), Bends, any radius with access door and Jointing with Solvent Cement and fixed-in-repairs, complete all as specified and as directed.

M&L PVC (SWR) floor trap 75 mm dia including jointing with solvent cement complete.

Excavating in post holes (or similar holes) each n exc 0.5cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm of soft /loose soil.

S&F galvanised corrugated mild steel sheeting, with two corrugation side lap fixed with 'L' type or 'J' type or cranked hooked bolts with washers in roof, 0.63mm thick, grade-O quality, with 120 grms/sqm zinc coating and grade 'B' Class 8 complete all as specified and directed by Engineer-in-Charge.

S&F Galvanised plain mild steel sheeting 0.63mm thickness fixed with l or J type or cranked hook bolts with washers, in roofs as in ridge etc all as specified and directed.

Preparation of new steel surfaces of steel or iron work or CGI/PGI sheeting in walls or roofing over 10 cm width or girth, not otherwise described and applying two coat of synthetic enamel paint over a coat of red oxide/zinc chromate in camouflaging (Disruptive) pattern (Green, Grey & Brown colour) complete all as specified and directed. (Make: Berger/Johnson/Nerolac/Asian/Shalimar)

S&F Roof trusses (framed), trussed, posts, struts, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats, base plate and gusset plates etc confirming to Fe 410 -W (Gde-E- 250) quality-A complete all as specified and directed.

Surface excavation n.exc (not exceeding) 30cm deep and averaging 15 cm, deep and getting out in soft/loose soil complete all as specified and directed.

M&L 100 mm PCC 1:4:8 type D-2 as in sub base complete all as specified and directed

M&L for sand filling of 50mm thick in floors or in foundations including watering and consolidation all specified and directed

M & L Machine pressed precast concrete interlocking paver block with grey cement and pigment any shape and size confirming to IS 15658-2006 of 60mm thickness M-35 grade with glossy finish colour shade complete all as specified and directed by Engr-in-Charge.(Sand will be measured & paid separately )

E/M PORTION

Taking down carefully copper/ aluminum point wiring (light , fan, socket or power) complete fittings such as switches,sockts, ceiling rose, regulators, angle/batten holder, light fittings and terminal box sheets etc making good disturbed surface of walls floors etc complete all as specified and directed by Engineer - in- Charge.

M & L Point wiring with FRLS stranded copper conductor PVC Insulated 1.5 Sqmm size, sheathed cable in including 20 mm dia PVC concealed conduit wiring with all accessories ie junction box inner and outer corners inner and outer bends , tees etc complete with PVC terminals box for mounting switches sockets fan regulators etc with continuous 1.0 Sqmm copper earth cable FR connected to common earth all as specified and directed for.

(a) One light point or one fan point controlled by one switch.

(b) One 3 pin socket outlet, 5 Amps, independent board.

(c) One 3 pin socket outlet, 5 Amps, same board with other switches.

All as per item No. 59 above given but wiring 2.5 Sqmm Stranded copper conductor FRLS cable for one 3/5 Pin socket 15 Amps and power plug controlled by one 15 amp switch all as specified and directed and earth wire FR 1.5 sqmm copper conductor cable.

M & L socket outlet 2 in 1, 3 pin, 6 and 16 A, flush type

M & L socket outlet , 3 pin, 6 A, flush type

M & L Switch piano , flush type single pole , one way 6 Amps.

M & L Switch piano , flush type single pole , one way 16 Amps.

S & F LED light fittings 1x20 watt, 220V,AC decorative box type with driver, holder including Led tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete. Make-Bajaj/Havells/Philips/CG

S & F LED luminaire 600mmx600 mm, 35/36 W,220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders and led lamp including for suitable for roof ceiling including connecting up with driver three core flexible copper conductor cable of suitable size from ceiling rose complete. Make-Bajaj/Havells/Philips/CG

S & F LED energy efficient flood light 50 W,220 V AC out door type IP 65 rated water proof pe with high efficiency PMMA diffuser soft glare free light complete with driver, holders and led lamp including for suitable for roof ceiling including connecting up with driver three core flexible copper conductor cable of suitable size from ceiling rose complete. Make-Bajaj/Havells/Philips/CG

Taking down carefully existing Ceiling fan including all accssories,and refix after completion of civil work complete all as specified and directed by engineer-in- charge

Taking down old u/s submain wiring any size.

M & L for sub main wiring with twin core copper conductor PVC insulated and unsheathed FRLS cable 2x4 Sqmm including1x 4 Sqmm cable FRLS as in continuous earth wire in and including PVC conduit concealed wiring with fitting and fixture arrangement. Make of Cable: – Finolex/Havells/Plaza

Taking down carefully existing hi wall split air-conditioning both indoor and out door unit including all accssories,and refix after completion of civil work complete all as specified and directed by engineer-in- charge

Supply and install hi wall split all-weather air-conditioning with copper condenser indoor/outdoor complete with cordless remote control unit and with in built air ioniser and plasma filter for better indoor air quality with minimum 3 star rating and EER 3.2 of capacity 1.5 TR

S&F voltage stabilizer 4 KVA,220V AC complete all as specified and directed by engineer -in-Charge.

Supply and fixing sheet metal clad enclosure suitable for aircondition/Water heater complete all as specified and directed.

Taking down old u/s DB,MCB,MCCB,any type any size.

Supply and fixing MCB SP 6 to 32 Amps, 240 Volts rating with rupturing capacity 10 KA 'C' curve type.

Supply and fixing MCB SPN 40 to 63 Amps, 240 Volts rating with rupturing capacity 10 KA 'C' curve type.

S & F Sheet sheet metal enclosure DB 12 way double door with 200 amps rated bus bar, 240 volts for fixing MCBs all as specified.

Supply & fixing ceiling rose, surface Bakelite, 65x50mm, three terminals.

Supply and Fixing Exhaust Fan AC single phase 230/240 Volts of size 450 mm sweep with louver shutter complete

Supply and fix electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 15Litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostae,NRV,connections piece etc , complete all as specified and directed by engineer-in-charge.

Disconnecting existing power supply and removing the main distribution box and relocate the suitable place and fixing after completion of addition and alteration work of the GDCC building and necessary connections and testing and commisssioning,complete all as specified and directed byu engineer-in-charge.

M & L for earthing complete with GI Plate of size 600 x 600 x 6 mm thick electrode buried directly in ground ( earth pit not less than 2.25 mtr deep below normal ground level ) with top edge of the plate not less than 1.5 mtr below normal ground level, connected to GI wire of size 4 mm dia. by means of nuts , bolts and washers of GI, protected by GI Pipe medium grade of 15 mm dia and with GI watering pipe medium grade 20 mm dia with funnel and wire mesh, including excavation and earth work in any type of soil and enough salt ,charcoal etc.Earth Pit of PCC (1:2:4) type B-1 with earth pit CI cover with suitable handle complete all as shown in electrical plate No 3 of SSR-2009 (Part-I) including testing on completion all as specified and directed by Engr-in-Charge.

Excavation in trenches not exceeding 1.5 mtr wide and not exceeding 1.5 mtr in depth for laying of cables or other items as required and getting out soil in soft/loose soil complete all as specified.

M&L for sand cushioning to under ground cable provided with a layer of sand 8 cm depth before laying of cable and 15 cm depth after laying and stretching the cable complete all as specified. Note: Punned thickness of sand shall be measured & paid.

M&L for new well burnt sub class 'B' bricks of nominal size 230X115X75 mm abutting each other for mechanical protection of cable with width equal to length of brick complete all as specified.

Returning filling in including spreading, leveling, watering and well ramming in layers not exceeding 25 cm complete all as specified.

Removing excavated material not exceeding 50 mtr and depositing where directed in a level not exceeding 1.5 mtr above the starting point of any type of soil complete all as specified.

Material and labour for cutting of road/ hard standing up to a size not exceeding 20cm width and not exceeding 60cm in depth for laying of cable protection pipe including making good the disturbed road/hard standing by providing PCC (1:2:4) type B1 to much the existing surface level complete all as directed.

Taking out old underground serviceable cable of any size and any make and keeping aside for the purpose of rerouting/relaying in new location/for requisite replacement/further disposal complete including taking out bricks all as specified. (Note: Earth work will be measured & paid separately).

Labour only for re-laying of serviceable (as obtained from taking out of cable ) cable of any type and size inclung making all electrical connection complete all as specified.

Supply, laying in replacement of UG cable XLPE insulated, armoured, heavy duty electric cable with aluminum conductor, 1100 volts grade, stranded aluminum conductor and including necessary cable lugs, bolts, nuts and washers complete all as specified and directed of following sizes :-. (Make: Poly cabNicco/Plaza/Gloster/Havells).

(a) 10 sqmm 4 core

(b) 16 sqmm 4 core

(c) 25 sqmm 4 core

(d) 35 sqmm 3.5 core

Supply and fixing in weather proof 2 core Sheathed flexible copper cable size 2.5 sqmm complete all as specified and as directed.

S&F warm white LED street light of 100 watt 230 V AC outdoor type high pressure die cast aluminum housing and heat resistant toughened glass complete with drivr,lamp,bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP65/66 protection complete all as specified and directed. Make:- Bajaj/Philips/Havells/CG/Wipro.

S&F warm white LED street light of 90 watt 230 V AC outdoor type high pressure die cast aluminum housing and heat resistant toughened glass complete with drivr,lamp,bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP65/66 protection complete all as specified and directed. Make:- Bajaj/Philips/Havells/CG/Wipro.

S&F warm white LED street light of 70 watt 230 V AC outdoor type high pressure die cast aluminum housing and heat resistant toughened glass complete with drivr,lamp,bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP65/66 protection complete all as specified and directed. Make:- Bajaj/Philips/Havells/CG/Wipro.

S&F, installation, commissioning and testing Junction boxes made of Lid PC and base is polystyrene Hensel reference : KG series suitable . Junction Boxes Size 217 x 253 x 115 mm in Grey RAL 7035 colour. Junction Box IP 65 Thermoplastic PS Polystyrene weatherproof Junction Box with multi level knockouts for cable glands in different sizes. The pre-moulded knockouts shall be available on top and bottom of the junction box to enable cable entries from both direction. The junction box shall have an optional cable entry at the bottom up Cable Size 25 Sq mm of the box via pre-moulded knockout to enable pole mounting option. Lid fasteners self closed will be tool operated. it will be sealable with accessories. The junction box shall have the provision of clamps for fixing to poles. The junction box with 4 Pole Terminal Strip and MCB SP 6 Amp 10 KA C Curve for LED light. In the event of formation of condensed water, the junction box shall have a minimum of two condensation knock-outs inside to ensure optimum safe performance. The junction box shall fulfill the following standards Weatherproof : Rainwater proof, temperature resistant. IEC 60670-22 : Particular requirements for connecting boxes and enclosures. IEC 60695 – 2 – 11 : Flame – retardant & Self-extinguishing. Glow Wire tested at minimum 750 deg C. IEC 60529 : IP 65 degree of protection. UV Resistant in accordance with IEC 61 439-1, Clause no 8.4.4 The Junction Box with Suitable Glands 3 Nos with each and chromium plated clamps, nut bolts complete all as per manufacturer’s instructions. Make : Cat Part :- KG 9003 of Hensel/Siemens/GE Power/Schneider/ L&T/ABB. Manufacturer should submit routine test certificate of CJB/PJB

M&L for Earthing complete with GI earth plate 600 x 600 x 6 mm thick buried directly in ground (earth pit not less that 2.25mtr deep below ground level ) with top edge of the plate not less than 1.5 m below normal ground level connected to 32x6 mm GI strip as earthing lead by means of brazing after tighten by bolts, nuts, check nuts and washers from earth pit to test point with protection GI pipe of size 50mm dia light grade and providing masonry enclosure including watering GI pipe (medium grade) 20 mm bore from bottom of earth pit to top of electrode and 20 mm GI pipe light grade for earth strip protection complete with earth pit in PCC 1:2:4 type B0 using 12 mm graded crushed stone aggregate, RCC cover, funnel, wire mesh including necessary excavation and earth work in any type of soil, returning filling in and removal of surplus soil complete all as specified and as directed. Note: GI strip 7.5 mtr included in the quoted rate from earth pit to test point

Supply & lay G I tubing light grade in protection of cable at road crossing /hard standing/pole protection fixed with clamps as per site requirement etc all as specified and directed for following sizes :- . Make : jindal/ TATA/prakash surya.

(b) 50 mm dia bore

(a) 40 mm dia bore

Note:- An amount of Rs. 13,130.00 on account of credit schdule for Sch 'A' Part-II Shall be deducted from the total amount of BOQ to arrive at the contract sum.

M/S BASHIR AHMAD AND SONS (BID ID -3346409)

M/s Gh Qadir and Sons (BID ID -3340365)