REPAIR TO BRICK WORK, JOINERY, PAINTING, PLUMBING WORK, ROOFING, PATHWAYS, HARDSTANDING, WALLS, DRAINS, FENCING, SEWAGE CLEANING AND OTHER MISC REPAIR AT RR UNITS UNDER AGE (I) BHALRA

Amount

Demolition of brick work or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars etc but excluding ashlar facings,dressed stonework and precast concrete articles complete all as specified and as directed by Engineer-in-charge.

M&L for brick work with sub class B bricks, straight or curved on plan exc 6m mean radius built in CM1:6 complete all as specified and as directed by Engineer-in-charge.

Description as per srl item No 2 here-in-before but except bricks.

M & L for walling of random rubble stone masonry uncoursed well bounded, bedded and solidly hearted built in CM 1:6, complete all as specified and as directed by Engineer-in-charge.

Desciption as per srl item No 4 here-in-before but except stone

Pre-cast cement concrete,1:3:6 type C1 (using 20 mm graded crushed stone aggregrates) as in bond stone set in cement mortar 1:6 and finishing exposed surface including necessary form work complete all as specified and directed complete all as specified and directed by Engineer-in-charge.

Extra over stone walling for hammer dressing to face stones and dressing of face beds and joints, as specified of random rubble walling with maximum depression on face from straight edge held against the dressed surface not exceeding 20mm lime or sand stone, complete all as specified and directed by Engineer-in-Charge.

M & L raised pointing to random rubble masonry uncourded or brought upto courses in CM 1:4, complete all as specified and as directed by Engineer-in-charge.

M & L for PCC 1:2:4 type B1 (Using 20 mm graded crushed stone aggregate) as in coping and similar works incl necessary from work complete all as specified and as directed by Engineer-in-charge.

S & F PVC (SWR) pipe 110 mm bore single socketed in any length with rubber ring joints as in weep holes complete all as specified and as directed by Engineer-in-charge.

Taking down old cement plaster on brick or stone walls, etc including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified and as directed by Engineer-in-charge.

M&L for 15mm thick rendering on fair faces of brick / concrete surfaces in cement mortar 1:6 and finished even and smooth without using extra cement, complete all as specified and as directed by Engineer-in-charge.

M & L for 15 mm thick rendering on fair faces or brick work or concrete surfaces in cement mortar 1:4 surface finished even and smooth without using extra cement complete all as specified and as directed by Engineer-in-charge.

M&L for 20mm thick cement plaster on stone masonry surfaces to random rubble masonry uncoursed or brought upto courses in CM 1:4, complete all as specified and as directed by Engineer-in-charge.

M&L applying two coats of cement base paint included preparation of new plastered surface complete all as specified and as directed by Engineer-in-charge.

Preparation of old decorated plastered or unplastered surfaces of walls, conices etc by brooming down, scrapping down smoke soot, moulds, moss and efflorescent salts and treating oil and greasy spots and applying one coat of cement base paint all as specified.complete all as specified and as directed by Engineer-in-charge.

Preparation of new plastered surfaces and applying two coat of oil bound distemper on new surfaces of walls complete all as specified and as directed by Engineer-in-charge.

M&L preparing of old surfaces of walls and applying one coat of oil bound distemper complete all as specified and directed by Engr-in-charge.

Preparation of old painted steel surfaces of any description not other wise described over 10 cm width or girth and applying one coat of synthetic enamel paint, design and pattern as approved by Engr-in-Charge complete all as specified.

Taking down chowkat or frames with shutters (without taking off shutters from the frames) n.exc 1.5 sqm each complete all as specified.

All as per srl item No 21 here-in-before but exceeding 1.5 sqm n exc 4 sqm each.

Taking down shutters exceeding 1 sqm but not exc 2 sqm each.

M&L for pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc. complete size 125 x 60 mm, including one shop coat of red oxide zinc chrome primer complete all as specified and as directed.

M&L for pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc. complete size 105 x 60 mm, including one shop coat of red oxide zinc chrome primer complete all as specified and as directed

S&F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, in opening as per specifiecation and drawings, complete all as specified and as directed.

M&L cement concrete (1:3:6) type C0 using 12.5 mm graded stone aggregate for filling in pressed steel chowkats, bed block or holdfast and the like complete all as specified and as directed

M&L for factory made, 2nd class hard wood rail and style 35 mm thick, plain framed, panelled shutters (two panels) with lock rail and panel of 9 mm BWP commercial ply or 12 mm veneered partical board with commercial veneering on both sides. The size of rail and stile as per IS-1003 (Part-I), kiln seasoned and chemically pressure treated complete all as specified and directed.

S&F 2nd class hard wood, glazed and skelton shutter 35mm thick open rebated and prepared to receive glass, guage, etc. (without sash bars), edges of framing palin, chamfered or rounded, fitted with cut & mitred beads for securing glass etc. sizes of members of shutters as specified in SSR 2009 Pt-I Section 8.24(b) supplied and fitted to chowkhats, complete all as specified and as directed.

S&F factory made solid panel PVC door shutter 30mm thick style consisting of frame made out of MS tubes for top & bottom rails MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width struck inside with solvent cement for style and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the styles & rails with suitable PVC sheet beading and jointed together with solvent cement complete all as specified.

S&F 100mm Butt hinges,heavy weight,cold rolled mild steel and fixed in repairs, complete all as specified and as directed

S&F Aluminium anodized, barrel tower bolt of extruded section, 150mm long, complete all as specified and as directed

S&F in repairs Aluminium handle, cast type, anodized, 150mm size, complete all as specified and as directed

S&F 300 mm Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast-aluminium alloy and fixed

S&F in repairs Helical door spring of size 300 mm including welding to steel chowkhats, complete all as directed at site.

S & F of 150mm floor door stopper of aluminium alloy body and tongue,anodised,with hard drawn steel spring,fixed in floor complete all as specified and as directed

M&L for preparation of wooden surfaces exceeding 10 cms width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified and as directed

S&F box type steel windows/Ventilator (factory made) outer frame made out ERW tube 'P' section 65X45X25 mm and shutter of ERW tube 'P' section 50mmX35mmX20mm openable (double shutter) with glazed shutter on extrernal side and gauzed shutter on internal side including steel pintel hinges steel handle 100 mm long mild steel tower bolt 02 nos on each shutter stopper of 'Z' section and its locking arrangement and mild steel hook and eyes suitable for fixing cooler /AC window complete all as specified and shown on drgs No CEPZTD-324/07 Sh 1/3 to 3/3 Note:- The quoted rate a shall also include (i). One shop coat of zinc chromate primer on all exposed surface and one coat of tar on the ends of steel surface in contact with bricks / concrte surface (ii) 4 nos MS steel lugs made of 20X5 mm Iron flat 200 mm long iii)10 mm Sq Bar grill/guard bar of design as directed (iv) PCC block for embedding lugs

S&F Galvanised mild steel wire cloth 0.50 nominal dia of wire and average width of aperture 1.18mm complete all as specified and as directed

S&F 3 mm thick sheet glass ordinary quality and glazing with oil putty or wooden beads in squares not exceeding 0.50 Sqm in each pane complete all as specified and as directed

Hacking out old broken glass of any thickness, size, quality or description from the wooden frames glazing with putty or fixed with wooden beads complete all as specified and directed.

M&L for preparation of steel and iron surfaces exceeding 10 cms width or girth and applying two coats of synthetic enamel paint over one coat of red oxide zinc chrome primer complete all as specified and directed.

S&F powder coated Anodised aluminium frame for doors, windows, ventilators with one or more rebates including jointing cleat for fixing etc complete all as specified and minimum thickness of powder coating 50 micron complete all as specified and directed.

S&F Powder coated aluminium door shutters, aluminum section weighing 0.55 Kg/m including necessary jointing cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screw etc complete all as specified and directed.

S&F powder coated anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1no.) complete all as specified

S&F 5.50 mm thick sheet glass fixing for Aluminium doors and windows including 25 micron reflective type sun control film complete all as directed

M & L Door closer hydraulically regulated, designation No. 2, universal type, suitable for door shutters of 701 to 850 mm in width and of weight between 36 to 60kg and fixed as in repairs (aluminium die cast body)

Dismantling CGI corrugated steel sheeting any gauge thickness including Nainital or similar pattern roof coverings, complete all as specified and as directed by Engineer-in-charge.

Dismantling timber scantling 40 sq cm and over in section framed work of any description

S&F for structural steel works of Fe 410W (Gde E 250) quality A, as in Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. including painted one shop coat of zinc chromate/red oxide primer paint (including preparation of surface) before fabrication as directed.

S & F 0.5mm Pre-painted galvalume aluminium Zinc coating steel GI based corrugated sheet of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall , fixed with self taping screws as specified and directed.

S & F 0.5mm Pre-painted galvalume aluminium Zinc coating steel sheet of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall , fixed with self taping screws as specified and directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation , etc.) or insulation boards/ slabs/ blankets any thikness including cover fillets.

S&F 4mm thick of size 605X605 mm, pre-premiered, self embossed, Reinforced Designer Board for false ceiling conforming to IS-14862 and ISO-8336:1993. as under:- (i)GI section frame work (powder coated) for white, pre-premiered, self embossed, reinforced designer board consisting of perimeter wall angle 19mmX19mmX0.45mm, cross 'Tee' 28.6mm (web)X 24mm flange .33mm thick powdered coated main tee 38(Web) X24mm flange 0.33mm thick. wall angle screwed fixed to brick wall/partition wall/concrete/RCC with the help of nylon sleeves and screws @ 610 mm C/C , (ii) Suspending GI main 'Tee' in both directions by means of hangers with alignment @ 1220mm C/C to soffits to from grid of 610X610mm cross Tee shall be provided @ 610mm C/C in both directions. Suitable provisions shall be made for fixing the recessed/surface mounting light fittings if any, complete all as specified and directed by Engr-in-Charge.

S&F 5mm thick Prelam PVC sheet in strips & channel feathered at the edges for fixing on Solid PVC walls lining, insulated PVC Wall Lining, and Solid PVC Partitions inclusive of Solvent Cement and fixing at site complete all as specified and directed.

S&F 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification and drawing.

M&L 6mm thick plywood grade BWR, type BB, fixed as in wall/ceiling, flat or sloping fixed with nails all as specified.

M&L 12mm pre-laminated partical board interior grade prelaiminated one side with decorative lamination and other side white lamination fixed with screw or nails.

S&F in repair Stainless steel drapery rods of 25 mm dia complete with coloured conical end balls at both end, dia not less then 50mm and fitted with and incl MS bracket size 150mm made to shape or 75mm dia MS end wall to wall round block made to shape in male and female pieces as required at site.

Dismantling floors hearth or wall tilling including cement mortor bedding (but not backing) removing serviceble tiles to store and rubbish off the premises.

M&L for colored non skid ceramic tiles 7 to 8 mm thick, area of each tile exc 0.11 sqm but n exc 0.18 sqm in floors etc set and jointed in neat cement slurry and pointed in colored cement to match shade, pattern, over and including 15 mm thick screed bed or bedding layers of cement mortar 1:6 complete all as specified and directed.

M&L Glazed ceramic coloured tiles, (Premier quality), of size 450 x 350 x 7 mm thick on vertical surfaces such as skirting, dados and risers to steps etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the surfaces over and including 10mm thick rendering in CM 1:4 all as specified & directed. Note : Design, shape and pattern of fixing of tiles shall be as directed by Engr-in-Charge.

M&L for Vitrified ceramic tiles 10mm thick (square/rectangular) light shade polished, area of each tiles n exc 0.36 sqm in floors etc set and jointed in neat cement slurry over and including 15mm thick screed bed in cement mortar 1:6 and pointed in white or coloured cement to match complete all as specified and as directed.

M&L for machine cut kota stone slab flooring 20-25mm thick laid over and including cement screed base laid 20 mm thick in cement mortar 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing, polishing and roughening the exisiting surface complete all as specified and directed.

M&L for machine cut kota stone slab 20-25 mm thick in riser of steps, skirting, dado and pillar laid over and including screed 10mm thick in CM 1:3 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing, polishing and roughening the existing surface complete all as specified and as directed.

M&L for 20mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like laid over and including 20mm thick in cement mortar (1:4) including roughening the exisiting surface and pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and as directed.

Dismantling water tanks and removing to store exc 250 & n.exc 500 litres.

Dismantling water tanks and removing to store exc 500 & n.exc 1000 litres.

Supplied and fixed Rotational moulded polyethlene water storage tanks three layered of 500 ltrs capacity ISI marked (cylindrical vergical with closed top) white in colour hoisted and fixed in position all as specified in SSR Part I including 20mm thick Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic bal screwed for iron pipe and fixed. (Minimum weight 20mm-210 gms including refixing of inlet, outlet & over flow pipe etc complete all as specified and as directed.

Supplied and fixed Rotational moulded polyethlene water storage tanks three layered of 1000 ltrs capacity ISI marked (cylindrical vergical with closed top) white in colour hoisted and fixed in position all as specified in SSR Part I including 25mm thick Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic bal screwed for iron pipe and fixed. (Minimum weight 20mm-210 gms including including refixing of inlet, outlet & over flow pipe etc complete all as specified and as directed.

Taking up or down steel tubing and connections, 15mm bore of pipe.

S & F tubes, medium grade, galvanised, with all fittings and fixed in short lengths complete to walls and ceilings or laid in floor , 15mm bore pipe.

All as per item No 71 here-in-before but fixing only.

Taking up or down steel tubing and connections, 20mm bore pipe.

S & F tubes, 'Medium grade, galvanised, with all fittings and fixed in short lengths complete to walls and ceilings or laid in floor , 20mm bore pipe.

All as per item No 74 here-in-before but fixing only.

S & F in repair 15 mm bore bib taps, fancy type chromium plated cast copper alloy with crutch or butterfly handle, screwed for iron pipe or for brass ferrule .

S & F in repair 15 mm bore stop/angle valves, cast copper alloy screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for union..

S & F in repair 20 mm bore stop valves, cast copper alloy screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for union..

S & F in repairs 15mm bore pillar tap fancy type, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered "Hot' or 'Cold' with long screwed shanks and flynuts, screwed for iron pipe.

S & F for PVC connections 15mm size with PTMT nuts of length 600mm.

S&F PVC waste pipe 32mm bore complete, all as specified

S & F in repairs 10 litres capacity PVC valveless , syphonic action type flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets complete all as specified and directed.

S&F in repairs Vitreous china wash down water closet pan (pedestal pattern), white including fixing bolts,flush pipe and joints complete all as specified and directed by Engr-in-Charge.

S&F Vitreous china squatting pan of patern 'Orissa pattern ' size 580x440 mm white with integral foot rests, flush pipe including provn of cement concrete bedding and making good the disturbed surface in PCC 1:2:4 type B-I using 20mm graded stone aggregate as in repair, complete all as specified and directed.

S&F as in repair tubular towel rail,aluminium anodised 20 mm dia `D' type 60 cm long between flanges, complete all as specified and directed.

S&F as in repair Grating doom 125 mm dia with waste hole of PTMT. (Minimum weight 40gms), complete all as specified and directed.

S&F as in repair Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long

S&F in repair chromium plated shower roses 125mm long with arm swivel joints any size including fixing to steel pipe or union .complete all as specified and directed by Engineer-In-Charge.

S&F in repair vitreous china wash hand basin white flat back of size 550x400 mm including bracket, (pedestal pattern )cutting for and pinning the ends of brackets or erecting stands exclusive of waste pipe but including brass chromium plated waste coupling with long screwed sank and fly nuts complete all as specified and directed.

S&F in repairs plastic water closet seat cover ,white/ black,closed pattern with flats bottom and cover and mild steel chromium plated or aluminium hinging device,of approved make and quality etc complete.

S&F Toilet paper holder with flat recessed type stainless steel complete all as specified and directed.

S&F Hand Shower (Health Faucet) (ABS Body) mild steel chromium plated suitable for 15mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified.

S&F ball valves high pressure of PTMT with appoxy coated alluminium rod and high density plastic ball screwed for iron pipe 20mm bore fixed in repair all as specified minimum weight 210grms

S&F 15 mm dia bore in repairs brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixed.

Demolition of Concrete ground floors and pavings n.exc 15cm thickness(below or above ground level) complete all as specified.

M&L for PCC (1:2:4) type B1 using 20mm graded crushed stone aggregate as in surface channel and drains finished even and smooth without using extra cement complete all as specified and directed.

M & L for 100 mm thick PCC 1:2:4 type B-2 (using 40 mm graded stone aggregate) as in hardstanding , path etc including finishing the rough surface without using extra cement and laid in alternate bays complete all as specified and directed.

Plain cement concrete 1:3:6 type C-2 using 40mm graded stone aggregate as in floor or paving 75mm thick, complete all as specified and directed.

M&L for Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand; complete all as specified and directed.

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as specified and directed.

M&L for precast chequered tiles (factory made rectified) of size tiles 300mX300mmX25mm over and including 20mm thick cement screed layer in cement mortar 1:4 ,top layer glazed made in grey cement and pigment in required patterns(compressive strength not less than 250 kg per Sqm) complete all as specified and directed.

TMT Bars , 10mm dia over cut to length , bent to shape reqd including cranking bending and binding with and including MS wire (annealed) not less than 0.9 mm dia or securing with clips all as specified .

Mild steel bars 6 mm to 8 mm dia., cut to length, bent to shape required, including cranking, bending spirally for hooping for columns , hooking ends and binding with and including mild steel wire ( annealed) not less than 0.90 mm dia.

Material and labour for precast cement concrete type B1 (1:2:4) using 20mm graded stone aggragate as in cover slab, manhole cover etc including necessary formwork complete all as specified and directed by Engr-in-charge.

Excavation in trenches n.exc 1.5m wide and n.exc 1.5m in depth for foundation etc and n.exc 10 Sqm on plan and n. exc 1.5 mtr in depth and getting out in any type of soil complete all as specified.

Returing filling in including spreading levelling watering and well ramming in layers not exceeding 25 cm thick

Removing excavated soil to a distance not exceeding 50 m and depositing where directed at a level not exceeding 1.50m above the starting point.

Demolition and breaking up drain pipes ( salt glazed ware, AC or Reinforced concrete ) set in cement mortar internal dia of pipe 150mm complete all as specified and directed

M&L for 150mm bore/inner dia Double wall corrugated HDPE pipes (SN-4) with intergral socket and necessary fttings, laid in trenches jointed as per manufacturer instruction complete all as spd and directed at site.

Cleaning the blockage in IWC, EWC, incl roding CI pipe after opening the oval access door of CI bend ,chamber etc upto septic tank and including replacement of chamber cover in position & removing the rubbish to a distance n.exc 50m all as specified and directed.

Desludging/dewatering/pumping/bailing out of contaminated water including cleaning of sludge, scum, silt (both organic and inorganic nature) and night soil from septic tank/soakage wells alongwith inlet/outlet chambers, manholes, soakage pits etc of any capacity after plugging the incoming sewage lines by suction (vaccum) type machine mounted on LCV facility of high pressure vaccum including removing the contaminated water in same tank to a place outside cantonment to a distance exceeding 50 mtr but not exceeding 100 mtr and burying in pits including rough excavation of pits and carriage of sludge to pits including spreading well in pits after burying of sludge, covering the pits with 25cm thick layer of earth and spreading bleaching powder over the covered area, complete all as specified and directed by Engineer-in-Charge.

m/s vaid contractor and builders (BID ID -3457188)

VEER TRADERS (BID ID -3462075)

M/S MAQBOOL AHMED BHAT (BID ID -3456289)

A S CONSTRUCTION (BID ID -3457084)

M/S Virinder Sharma (BID ID -3456960)