Upgradation-Strengthening and 5 Years Routine Maintenance of Roads- 2 nos.in Package no. MGSMT-23-2022-23 at Sattur Block of Virudhunagar District under MGSMT-2022-23.

Amount

Part-1:- Kumarapuram up to District limit

Part-A:- Upgradation work

Clearing Scrub Jungle without alignment for the widening of the formation of the road cutting of trace up to 30mm girth products the cleaning are to be stocked in such a place as ordered by the departmental officer and the ground shall be left in a perfectly clean condition. All holes of hollows whether original, existing (or) produced by digging of roots shall than be carefully filled up the earth well rammed and leveled of and the entire work completed in all respect as per SI 17 (2).

Earth work excavation and depositing on back with an intial of 10m and lift 2m in hard stiff clay, stiff black cotton, hard red earth and earth mixed with small size boulders, hard gravelly soil etc., as per SS 20A including laying and spreading in layer etc.complete.

Construction of Granular Sub base by providing well graded material (25 mm to 4.75 mm IRC HBG metal @ 65 %,4.75 to 2.36mm IRC HBG metal @20%&2.36 mm below IRC HBG metal @15%)& (the material passing 425 microns sieve shall have liquid limit and plasticity index not more than 25 & 6% repectively) spreading in uniform layers with motor grader on prepared surface mixing by mix in place method with rotovator at OMC and compacting with three wheel 80-100 KN capacity and finished in accordance with the requirements of the specification and thickness as per approved plans or as directed by the Engineer (Mix -in - place method) .

Providing and laying spreading and compacting graded stone aggregate to Wet Mix Macadam(WMM) specification including premixing the material with water at OMC in machanical mix plant carriage of mixed material by tipper to site laying in uniform layers with pavers in SubBase/Base course on well prepared surface and compacting with vibratory roller to achieve the desired density including cost of material,labour charges, rentals for machinery, fuel and all other incidental charges etc., complete.

Providing laying and compacting red gravel in accordance with requirements of the specification materials shall be in one or more layers as necessary including watering, consolidating by the power roller rolling and all labour charges for soiling including hire charges for consolidation etc. complete. Km 0/0- 0/1

Providing laying and compacting red gravel in accordance with requirements of the specification materials shall be in one or more layers as necessary including watering, consolidating by the power roller rolling and all labour charges for soiling including hire charges for consolidation etc. complete. Km 0/0- 1/4

Construction of subgrade for 300mm depth by using excavated earth at site by mechanical means and then adding 50% of defict materials by using stone dust obtained from quarry with all lifts and leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of Table 300.2 with lead upto 1000 m as per Technical Specification Clause 303.1.( subgrade using stone dust to improve CBR 7 to 9)

Applying Prime coat over WBM/WMM @ 7.00Kg RS-1 Bitumen Emulsion / 10 sq.m including labour for spraying, hire charges for bitumen sprayer etc. Comp.

Applying Tack coat over primed surface @ 2.50Kg RS-1 Bitumen Emulsion / 10 sq.m including labour for spraying, hire charges for bitumen sprayer etc. Comp.

BITUMINOUS CONCRETE USING cmp (Grade-II) Providing and laying Bituminious concrete using 0.13cum of 19.00-9.50mm. 0.17cum of 9.5-2.36 and below with 50.3kgs of VG30/VG40 include 8% plastic waste heating the bitumen and aggregates to required temperature and mixing them in required temperature in central hot mix plant 20-30 ton capacity, carrying the mix by tipper trucks to paver site, spreading the mix to uniform thickness of 40mm with mechanical paver to the specified grades and cross sections and consolidated by 8-10 tonnes vibratory/phenumatic roller to the required density etc., including labour for attending to paver to site etc.including hire charges and fuel charges foe 20-30t CMP with bitumen boiler, tipper trucks,paver finisher/9m paver finisher,vibratory/phenumatic roller and all other tools and plants required, including fuel and all other incidental charges etc., complete as per specification using CMP as per clauses 507 of MORTH Part-5

Provision for Hectametre stone of size

Provision for Kilometre stone of size

Providing and erecting of Retro - Reflectorised Cautionary , Mandatory and Information signs (with Definition Board ) made out of High intensity Prismatic grade Sheeting Confirming to Type-IV Standard of IRC-67 : 2012 and ASTM D 4956-09 , Specification and fixed over 2 mm thick Aluminium sheet fixed over a back Supporting frame of 25 mm X 25mm X 3mm Mild steel angel angle and supported on a mild steel angle post 75 mm X 75 mm X 6 mm with a clear height of not less than 2.10 m from the ground level to the bottom of the sign board and 0.60 m below ground level . The sign post should be painted asper IRC 67 -2012 and firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45 cm X 45 cm X 60 cm size including cot and conveyance of all materials , Equipment , machinery and labour with all leads and lifts , Loading charges necessary for satifactory completion of the works as directed by the engineer in Charge . High intensity Retro - Reflectro sheet shall consist of minimum coefficient of Retro - Reflection as per Table 6.6 of IRC 67 - 2012 . The retro - Reflective sheeting shall be covered under 7 year warrenty issued for field performance and certified copy of theree years outdoor exposure report shall be obtained as per IRC 67 - 2012 (As per MORT & H Specification no .801) - 90 cm equilaterial Triangle with definition board

Providing and erecting of Retro - Reflectorised Cautionary , Mandatory and Information signs (with Definition Board ) made out of High intensity Prismatic grade Sheeting Confirming to Type-IV Standard of IRC-67 : 2012 and ASTM D 4956-09 , Specification and fixed over 2 mm thick Aluminium sheet fixed over a back Supporting frame of 25 mm X 25mm X 3mm Mild steel angel angle and supported on a mild steel angle post 75 mm X 75 mm X 6 mm with a clear height of not less than 2.10 m from the ground level to the bottom of the sign board and 0.60 m below ground level . The sign post should be painted asper IRC 67 -2012 and firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 30 cm X 30 cm X 60 cm size including cot and conveyance of all materials , Equipment , machinery and labour with all leads and lifts , Loading charges necessary for satifactory completion of the works as directed by the engineer in Charge . High intensity Retro - Reflectro sheet shall consist of minimum coefficient of Retro - Reflection as per Table 6.6 of IRC 67 - 2012 . The retro - Reflective sheeting shall be covered under 7 year warrenty issued for field performance and certified copy of theree years outdoor exposure report shall be obtained as per IRC 67 - 2012 (As per MORT & H Specification no .801) - 60 cm High Octagon with definition board

Providing and laying of hot applied Thermoplastic compound 2.5 mm thick including reflectoising glass beads @ 250 gms per Sqm area , Thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC :35 . The finished surface to be level , uniform and free streaks and holes etc complete as per MORT & H specification No.803 - Road Marking - Edge line

Provision for Maintenance and Name board

Providing and fixing reflective road studs of "category B" raised pavement markers made out of poly carbonae/ABS moulded body and reflective panels(bi-covex reflectors)with micro prismatic lens capable of providing total internal reflection of the lifht entering the lens face with retro - reflectance and chromaticity values conforming to ASTM D4280. The reflective raised pavement markers shall also fonfirm to the MORTH circular NI. RW/NH. 33023/10/97-DO.III dt 11.06.97 and the length, height and width of the body shall not be less than 100 mm, 15 mm and 90mm and base of markder shall be flat within 1.3 mm. The marker shall support a load of 13635 Kg tested in accordance with ASTM D 4280. Lenses shall be moulded of Poly carbonate or methyl methecrylate fonforming to ASTM D788. The area of each retro - refloctory surface shall not be less than 13.0 sq. cm.. The slope or retro - refloctory surface shall be 35 + 5 degree to base. Each 4reflector shall have a CIL not less than values specified in table 2 of said MORTH & H circular and two cylindrical polymer shanks of not less than 20 mm diameter and not less than 30 mm length shall be provided for better anchorage.

CD works-1:- Construction of 2 x 5 Span Rcc Culvert @ Ch - 850m

Earth work Excavation for Foundation in all soils and Sub Soil to full depth as may be directed except in hard rock requiring blasting but inclusive of shoring strutting and requiring the sides of foundation.

Collection and supply of M.Sand and filling into the basement including cost and conveyance to the site and all labour charges for filling as per standard specification

Cement mortar 1:3:6 mix using 40mm ISS metal (Using M-Sand) including cost and conveyance of all materials to site and all labour charges for mixing, laying, and curing etc complete for 10 cum

CENTERING BELOW GL: Supplying and erecting centering shuttering including necessary supports for plane surface in foundation and basement and in all floors for R C C column footing column plinth beam, beams, roof slabs, staircase steps, bed blocks, critical pier etc using mild steel sheets of size 90 x 60 cm and 10 guage stiffened, welded with mild steel angles of size 25mmx25mmx3mm for boarding laid over silver oak (country wood) scantlings of size 10cm x 6.5cm spaced of about 90cm centre to centre and supported by casurina props of 10cm to 13cm dia spaced at 75cm centre to centre complete complying with standard specifications and as directed by departmental officers including conveyance of all materials to site and proper centering etc complete.

CENTERING ABOVE GL: Supplying and erecting centering shuttering including necessary supports for plane surface in foundation and basement and in all floors for R C C column footing column plinth beam, beams, roof slabs, staircase steps, bed blocks, critical pier etc using mild steel sheets of size 90 x 60 cm and 10 guage stiffened, welded with mild steel angles of size 25mmx25mmx3mm for boarding laid over silver oak (country wood) scantlings of size 10cm x 6.5cm spaced of about 90cm centre to centre and supported by casurina props of 10cm to 13cm dia spaced at 75cm centre to centre complete complying with standard specifications and as directed by departmental officers including conveyance of all materials to site and proper centering etc complete.

Cement concrete 1:2:4 mix using 40mm ISS metal (Using M-Sand) including cost and conveyance of all materials to site and all labour charges for mixing, laying and curing etc complete for 10 cum

Supplying and fabrication of steel including cost and conveyance of steel to site and all labour charges for straightening, cutting to length, bending to shape and tying in position and forming grills for all R.C.C works

Reinforced cement concrete 1:1.5:3 mix using 20mm ISS metal (using M-Sand) including cost and conveyance of all materials to site and all labour charges for mixing, laying, and curing etc complete for 10 cum

Fillng behind abutments and wing with clean gritty gravel including and cost and conveyance of gravel to work site , laying, handling nd filling in layers, tamping underr optimum moisture content to get the maximum density including watering with all leads for water and all other incidental chargers etc, complete for filling behind the abutment and wings

Supplying and fixing of Bitumen pad for expansion joints

Supplying and fixing of Bitumen pad for expansion joints

Providing Tar sheet

Providing Weep holes

CD works-2:- Construction of 1.5 m Span Rcc Culvert 2 Nos@ Ch - 020,150 m.

Earth work Excavation for Foundation in all soils and Sub Soil to full depth as may be directed except in hard rock requiring blasting but inclusive of shoring strutting and requiring the sides of foundation.

Supplying and Filling foundation and basement with filling sand in layers not more than 15cm . Thick well ramed, watered and compacted Complete complying with stanard specification.

Cement concrete 1 : 4 : 8 mix using 40mm HBG metal for foundation including watering wherever necessary and laid in layers of not more than 15cm thick., compacting etc., complete complying with standard specifications and as directed.

Cement concrete 1 : 3 : 6 mix using 40mm HBG metal for foundation including watering wherever necessary and laid in layers of not more than 15cm thick., compacting etc., complete complying with standard specifications and as directed.

Cement concrete 1 : 2 : 4 mix using 20mm HBG metal for foundation including watering wherever necessary and laid in layers of not more than 15cm thick., compacting etc., complete complying with standard specifications and as directed.

Cement concrete 1:1.5:3 using 20mm ISS HBG metal for all RCC item of works excluding cost of Rein forcement and fabricating charges, centering and shuttering but including curing and providing fixtures like fan clamps in the RCC floor or roof slabs wherev

Supplying and Fabricating and placing in position MS steel or ribbed for steel for all reinforced cement concrete works as per the design given including cost of steel and binding wire in all floors etc, Complete complying with stanard specification.

Supplying & Erecting centering for sides & soffiots including necessary supports & strutting upto 3.29m height for plane surfaces in all floors with all cross bracings using mild steel sheets of size 90 x 60cm & 10 gauge stiffened, welded with steel angle

Supplying & Erecting centering for sides & soffiots including necessary supports & strutting upto 3.29m height for plane surfaces in all floors with all cross bracings using mild steel sheets of size 90 x 60cm & 10 gauge stiffened, welded with steel angle

Providing Bitumen Pad

Providing Tar sheet

Providing Weep holes

CD works-3:- Construction of 3 m Span Rcc Culvert @ Ch - 1350 m.

Earth work Excavation for Foundation in all soils and Sub Soil to full depth as may be directed except in hard rock requiring blasting but inclusive of shoring strutting and requiring the sides of foundation.

Supplying and Filling foundation and basement with filling sand in layers not more than 15cm . Thick well ramed, watered and compacted Complete complying with stanard specification.

Cement concrete 1 : 4 : 8 mix using 40mm HBG metal for foundation including watering wherever necessary and laid in layers of not more than 15cm thick., compacting etc., complete complying with standard specifications and as directed.

Cement concrete 1 : 3 : 6 mix using 40mm HBG metal for foundation including watering wherever necessary and laid in layers of not more than 15cm thick., compacting etc., complete complying with standard specifications and as directed.

Cement concrete 1 : 2 : 4 mix using 20mm HBG metal for foundation including watering wherever necessary and laid in layers of not more than 15cm thick., compacting etc., complete complying with standard specifications and as directed.

Cement concrete 1:1.5:3 using 20mm ISS HBG metal for all RCC item of works excluding cost of Rein forcement and fabricating charges, centering and shuttering but including curing and providing fixtures like fan clamps in the RCC floor or roof slabs wherev

Supplying and Fabricating and placing in position MS steel or ribbed for steel for all reinforced cement concrete works as per the design given including cost of steel and binding wire in all floors etc, Complete complying with stanard specification.

Supplying & Erecting centering for sides & soffiots including necessary supports & strutting upto 3.29m height for plane surfaces in all floors with all cross bracings using mild steel sheets of size 90 x 60cm & 10 gauge stiffened, welded with steel angle

Supplying & Erecting centering for sides & soffiots including necessary supports & strutting upto 3.29m height for plane surfaces in all floors with all cross bracings using mild steel sheets of size 90 x 60cm & 10 gauge stiffened, welded with steel angle

Fillng behind abutments and wing with clean gritty gravel including and cost and conveyance of gravel to work site , laying, handling nd filling in layers, tamping underr optimum moisture content to get the maximum density including watering with all leads for water and all other incidental chargers etc, complete for filling behind the abutment and wings

Providing Bitumen Pad

Providing Tar sheet

Providing Weep holes

CD works-4:- Construction of 1.5 m Span Rcc Culvert @ Ch - 1150 m.

Earth work Excavation for Foundation in all soils and Sub Soil to full depth as may be directed except in hard rock requiring blasting but inclusive of shoring strutting and requiring the sides of foundation.

Supplying and Filling foundation and basement with filling sand in layers not more than 15cm . Thick well ramed, watered and compacted Complete complying with stanard specification.

Cement concrete 1 : 4 : 8 mix using 40mm HBG metal for foundation including watering wherever necessary and laid in layers of not more than 15cm thick., compacting etc., complete complying with standard specifications and as directed.

Cement concrete 1 : 3 : 6 mix using 40mm HBG metal for foundation including watering wherever necessary and laid in layers of not more than 15cm thick., compacting etc., complete complying with standard specifications and as directed.

Cement concrete 1 : 2 : 4 mix using 20mm HBG metal for foundation including watering wherever necessary and laid in layers of not more than 15cm thick., compacting etc., complete complying with standard specifications and as directed.

Cement concrete 1:1.5:3 using 20mm ISS HBG metal for all RCC item of works excluding cost of Rein forcement and fabricating charges, centering and shuttering but including curing and providing fixtures like fan clamps in the RCC floor or roof slabs wherev

Supplying and Fabricating and placing in position MS steel or ribbed for steel for all reinforced cement concrete works as per the design given including cost of steel and binding wire in all floors etc, Complete complying with stanard specification.

Supplying & Erecting centering for sides & soffiots including necessary supports & strutting upto 3.29m height for plane surfaces in all floors with all cross bracings using mild steel sheets of size 90 x 60cm & 10 gauge stiffened, welded with steel angle

Supplying & Erecting centering for sides & soffiots including necessary supports & strutting upto 3.29m height for plane surfaces in all floors with all cross bracings using mild steel sheets of size 90 x 60cm & 10 gauge stiffened, welded with steel angle

Providing Bitumen Pad

Providing Tar sheet

Providing Weep holes

Part-B:- Maintenance work

Maintenance Towards the charges for routline maintenance of the road work executed under MGSMT including dressing of berms by refilling the gully with the earth from borrow pits, cleaning of wild seasonal growth on berms, destilting of side drains and CD works, white washing guard stones, painting of KM, HM stones, parapets, cutting of branches of trees, refixing displaced guard stones, caution boards, speed limit boards etc., with the periodicity for the above activities as prescribed in IRC-SP-20:2002 and as directed by the departmental officers except for the constructional defects which has to be rectified by the contractor at his own cost

For the First Year from the date of completion of work

For the Second Year from the date of cpmpletion of work

For the Third Year from the date of completion of work

For the Fourth Year from the date of completion of work

For the Fifth Year from the date of completion of work

Part-2:- Uppathur main road to kattu ayyanar koil road

Part-A:- Strengthening work

Clearing Scrub Jungle without alignment for the widening of the formation of the road cutting of trace up to 30mm girth products the cleaning are to be stocked in such a place as ordered by the departmental officer and the ground shall be left in a perfectly clean condition. All holes of hollows whether original, existing (or) produced by digging of roots shall than be carefully filled up the earth well rammed and leveled of and the entire work completed in all respect as per SI 17 (2).

Picking Existing old Bt surface upto 50 to 100cm thick include all cost and conveyance of amterials etc., complete

Earth work excavation and depositing on back with an intial of 10m and lift 2m in hard stiff clay, stiff black cotton, hard red earth and earth mixed with small size boulders, hard gravelly soil etc., as per SS 20A including laying and spreading in layer etc.complete.

Providing and laying spreading and compacting graded stone aggregate to Wet Mix Macadam(WMM) specification including premixing the material with water at OMC in machanical mix plant carriage of mixed material by tipper to site laying in uniform layers with pavers in SubBase/Base course on well prepared surface and compacting with vibratory roller to achieve the desired density including cost of material,labour charges, rentals for machinery, fuel and all other incidental charges etc., complete.

Providing laying and compacting red gravel in accordance with requirements of the specification materials shall be in one or more layers as necessary including watering, consolidating by the power roller rolling and all labour charges for soiling including hire charges for consolidation etc. complete. Km 0/0- 0/8

Applying Prime coat over WBM/WMM @ 7.00Kg SS-1 Bitumen Emulsion / 10 sq.m including labour for spraying, hire charges for bitumen sprayer etc. Comp.

Applying Tack coat over primed surface @ 2.50Kg RS-1 Bitumen Emulsion / 10 sq.m including labour for spraying, hire charges for bitumen sprayer etc. Comp.

BITUMINOUS CONCRETE USING cmp (Grade-II) Providing and laying Bituminious concrete using 0.13cum of 19.00-9.50mm. 0.17cum of 9.5-2.36 and below with 50.3kgs of VG30/VG40 include 8% plastic waste heating the bitumen and aggregates to required temperature and mixing them in required temperature in central hot mix plant 20-30 ton capacity, carrying the mix by tipper trucks to paver site, spreading the mix to uniform thickness of 40mm with mechanical paver to the specified grades and cross sections and consolidated by 8-10 tonnes vibratory/phenumatic roller to the required density etc., including labour for attending to paver to site etc.including hire charges and fuel charges foe 20-30t CMP with bitumen boiler, tipper trucks,paver finisher/9m paver finisher,vibratory/phenumatic roller and all other tools and plants required, including fuel and all other incidental charges etc., complete as per specification using CMP as per clauses 507 of MORTH Part-5

Provision for Hectametre stone of size

Providing and erecting of Retro - Reflectorised Cautionary , Mandatory and Information signs (with Definition Board ) made out of High intensity Prismatic grade Sheeting Confirming to Type-IV Standard of IRC-67 : 2012 and ASTM D 4956-09 , Specification and fixed over 2 mm thick Aluminium sheet fixed over a back Supporting frame of 25 mm X 25mm X 3mm Mild steel angel angle and supported on a mild steel angle post 75 mm X 75 mm X 6 mm with a clear height of not less than 2.10 m from the ground level to the bottom of the sign board and 0.60 m below ground level . The sign post should be painted asper IRC 67 -2012 and firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45 cm X 45 cm X 60 cm size including cot and conveyance of all materials , Equipment , machinery and labour with all leads and lifts , Loading charges necessary for satifactory completion of the works as directed by the engineer in Charge . High intensity Retro - Reflectro sheet shall consist of minimum coefficient of Retro - Reflection as per Table 6.6 of IRC 67 - 2012 . The retro - Reflective sheeting shall be covered under 7 year warrenty issued for field performance and certified copy of theree years outdoor exposure report shall be obtained as per IRC 67 - 2012 (As per MORT & H Specification no .801) - 90 cm equilaterial Triangle with definition board

Providing and erecting of Retro - Reflectorised Cautionary , Mandatory and Information signs (with Definition Board ) made out of High intensity Prismatic grade Sheeting Confirming to Type-IV Standard of IRC-67 : 2012 and ASTM D 4956-09 , Specification and fixed over 2 mm thick Aluminium sheet fixed over a back Supporting frame of 25 mm X 25mm X 3mm Mild steel angel angle and supported on a mild steel angle post 75 mm X 75 mm X 6 mm with a clear height of not less than 2.10 m from the ground level to the bottom of the sign board and 0.60 m below ground level . The sign post should be painted asper IRC 67 -2012 and firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 30 cm X 30 cm X 60 cm size including cot and conveyance of all materials , Equipment , machinery and labour with all leads and lifts , Loading charges necessary for satifactory completion of the works as directed by the engineer in Charge . High intensity Retro - Reflectro sheet shall consist of minimum coefficient of Retro - Reflection as per Table 6.6 of IRC 67 - 2012 . The retro - Reflective sheeting shall be covered under 7 year warrenty issued for field performance and certified copy of theree years outdoor exposure report shall be obtained as per IRC 67 - 2012 (As per MORT & H Specification no .801) - 60 cm High Octagon with definition board

Providing and laying of hot applied Thermoplastic compound 2.5 mm thick including reflectoising glass beads @ 250 gms per Sqm area , Thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC :35 . The finished surface to be level , uniform and free streaks and holes etc complete as per MORT & H specification No.803 - Road Marking - Edge line

Provision for Maintenance and Name board

Providing and fixing reflective road studs of "category B" raised pavement markers made out of poly carbonae/ABS moulded body and reflective panels(bi-covex reflectors)with micro prismatic lens capable of providing total internal reflection of the lifht entering the lens face with retro - reflectance and chromaticity values conforming to ASTM D4280. The reflective raised pavement markers shall also fonfirm to the MORTH circular NI. RW/NH. 33023/10/97-DO.III dt 11.06.97 and the length, height and width of the body shall not be less than 100 mm, 15 mm and 90mm and base of markder shall be flat within 1.3 mm. The marker shall support a load of 13635 Kg tested in accordance with ASTM D 4280. Lenses shall be moulded of Poly carbonate or methyl methecrylate fonforming to ASTM D788. The area of each retro - refloctory surface shall not be less than 13.0 sq. cm.. The slope or retro - refloctory surface shall be 35 + 5 degree to base. Each 4reflector shall have a CIL not less than values specified in table 2 of said MORTH & H circular and two cylindrical polymer shanks of not less than 20 mm diameter and not less than 30 mm length shall be provided for better anchorage.

Part-B:- Maintenance work

Maintenance Towards the charges for routline maintenance of the road work executed under MGSMT including dressing of berms by refilling the gully with the earth from borrow pits, cleaning of wild seasonal growth on berms, destilting of side drains and CD works, white washing guard stones, painting of KM, HM stones, parapets, cutting of branches of trees, refixing displaced guard stones, caution boards, speed limit boards etc., with the periodicity for the above activities as prescribed in IRC-SP-20:2002 and as directed by the departmental officers except for the constructional defects which has to be rectified by the contractor at his own cost

For the First Year from the date of completion of work

For the Second Year from the date of cpmpletion of work

For the Third Year from the date of completion of work

For the Fourth Year from the date of completion of work

For the Fifth Year from the date of completion of work

GST Amount for providing Service to the above Government Contract Works. { GST Amount is the Total GST Amount for total overall quoted amount above this row in column "BB" for all works in this package}

VENKATESWARA CONSTRUCITON