Construction of Children Park near Padmapukuria Health Centre under Booth no.75

P.W.D, Page No. 1, Item No.- 2 (a)

Earth work in excavation of foundation trenches or drains. in all sorts of soil (including mixed soil but excluding laterite or sandstone) including removing. Spreading or stacking the spils within a lead of 75 m. as directed. The item includes necessary trimming the sides of trenches. leveling. dressing and ramming the bottom. bailing out water as required complete . (a) Depth of foundation upto 1500mm

Page No.- 1, Item No.- 3(a).

Earth work in filling in foundation trenches or plinth with good earth, in layers not exceeding 150 mm. including watering and ramming etc. layer by layer complete. (Payment to be made on the basis of measurement of finished quantity of work). (a) With earth obtained from excavation of foundation.

P.W.D, Page No. 47, Item No. 3

supplying and laying polythene Sheet ( 150 gm / sq.m) over damp proof couse or below flooring or roof terracing or in foundation trenches.

Page No.- 23 / Item No.- 1(a)

(I) Cement concrete with graded jhama khoa (30 mm size excluding shuttering) In ground floor (a) 1:3:6 proportion

Page No.- 15, Item No.- 7(a) (rate analysis)

Brick work with 1st class bricks in cement mortar (1:4) (a) Foundation and plinth groung floor

P.W.D, Page No.- 26, Item no.- 10(i)

Ordinary Cement concrete (mix 1:1.5:3) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement if any, in ground floor as per relevant IS codes. (i) Pakur Variety

Page No.- 42, Item No.- 36(c)

Hire and labour charges for shuttering with centering and necessary staging upto 4 m using approved stout props and thick hard wood planks of approved thickness with required bracing for concrete slabs, beams and columns, lintels curved or straight including fitting, fixing and striking out after completion of works (upto roof of ground floor) (c) 9 mm to 12 mm thick approved quality Ply board shuttering as per decision & direction of Engineer-In-Charge.

Page No.-64, Item No.-35(B)(b)(ii) (Analysis Rate)

Supplying, fitting & fixing 1st quality Ceramic tiles in walls and floors to match with the existing work & 4 nos. of key stones (10mm) fixed with araldite at the back of each tile & finishing the joints with white cement mixed with colouring oxide if required to match the colour of tiles including roughening of concrete surface, if necessary or by synthetic adhesive & grout materials etc. B) Wall b) Area of each tile above 0.09 Sq.m i) Coloured decorative

Page No.- 74, Item No.- 46 (ii)

Supplying and laying chequered tiles of any shade & of approved quality with (1:1½:3) cement concrete laid in panels or patterns as directed in pavement, footpath etc. including necessary underlay 25 mm thick [avg] cement mortar (1:3) complete in all respect with all labour and materials. [Using cement slurry @ 4.4 kg/Sq.m at back side and @2.4 kg/Sq.m for joint filling] Red Variety , 30 mm thick

Page No.- 62, Item no.- 32.

Supplying, fitting & fixing granite slabs 15mm to 18 mm. thick with uniform texture & without decorative veins in columns, wall, facia etc. with 15 mm thick [avg] cement mortar (1:2) including making suitable arrangements to hold the stones properly by brass / copper hooks including pointing in cement mortar (1:2) (1 white cement : 2 marble dust) with admixture of pigment matching the stone shades all complete as per direction of the Engineer-in-charge including cost of all materials, labours, scaffolding, staging ,curing and roughening of concrete surface complete. Area of each Granite slab > 0.6 upto 1.0 square metre. [Using cement slurry at back side of granite @ 4.4 kg/sq.m & white cement slurry for joint filling @ 1.8 kg/sq.m]

Page No.- 101, Item No.-2A

M.S. structural works with hollow sections (square or rectangular shape) conforming to IS: 806-1968 & IS:1161-1998) connected to one another with bracket, gusset, cleat as per design, drawing & direction of Engineer-in-Charge complete including cutting to requisite shape & size, fabrication including metal arc welding conforming to IS: 816-1969 & IS: 9595 using electrodes of approved make and brand conforming to IS:814- 2004, haulage, hoisting and erection all complete. The rate includes the cost of all M.S. Hollow section, all consumables such as electrodes, gas and hire charges of all tools and plants and labour reqired for execution and all incidental chages (such as electricity, labour insurance) etc. complete. i) For roof truss works a) Span up to 12 Mtr

Page No.-82, Item no.- 14.

Supplying, fitting & fixing Zn-Al alloy (55% Al & 45% Zn) coating of 150 grams per sq. metre (followed by colour coated on both side) steel sheet work having minimum yield strength of 550 Mpa of trapizoidal profile of approved make (excluding the supporting frame work) fitted and fixed with 55 mm & 25 mm self tapping screw, EPDM Washer 16 mm dia & 3 mm th. washer etc. complete with 150 mm end lap and one corrugation minimum side lap. (Payment to be made on area of finished work). (i) In Roof:- a) With 0.5 mm thick sheet

Page No.-82, Item no.- 11(b).

Galvanised iron sheet eaves gutter fitted and fixed with necessary 50 mm X 6 mm M.S flat bar clamps bent to design,bolts, nuts, washers etc. complete. Eaves gutter made of 0.63 mm. sheets.(300mm End lapping) (b) 300 mm. wide gutter

Page No.- 200, Item no.- 1(a).

Priming one coat on steel or other metal surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc.

Page No.- 200, Item no.- 2(A)(b)(ii).

Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc. on the surface, if necessary. On steel or other metal surface. Two coats ( with any shade exept white)

Ref. Item No. 36, Approved Tender ID 2022_DSDA_367956_1

Supplying, and installing of FRP made double see saw suitable for age group of 3 to 10 years children customized with MS Pillar material or frame work having specified dimension. Its need attraclive finish designs as well as beautiful color combinations which makes these highly preferred for use in park areas. The Manufacturer/supplier shall provide full details of the FRP materials, including all associated manufacturing processes, test certificales, acShesive,and fasteners. The Manufacturer/supplier shall responsible for all labour. materials, equipment, carriage and all other incidentals cost govemer by this specification to manufacture the FRP components in accordance with any structural drawings provided by the EIC. Body Material FRP Supporting Malerial MS(Steel Components all powder coated with anticarrosion treatment) Colourm As desierd by EIC Usage/Application-Outdoor Waterproof: Yes

Ref. Item No. 34, Approved Tender ID 2022_DSDA_367956_1

Supplying, and installing of Girrape shape FRE made Plain Slide Senior(length=6m,height«2 m)suitable for 3 t 10 years children having specified dimension fifteu wim Ms ledder material Its need altractive finish designs as wes ss hemu color combinalions which makes these highly preferren ior use in park areas. The Manufacturer/supplier shall provide full details o the Fe materials, including all associated nufacluring processes, test certificates, adhesive,and fasteners. The Manufacturer/supplier shall sponsible for all labour. maferials, equipment, carriage and all other incidentals cost govemed by this specification to manufacture the FRP components in accordance with any structural drawings provided by the EIC. Platform Height =1800-2000 mm length=6.00 mtr (approximately) Body Material=FRP Ladder Malerial=MS(Steel Components all powder coated with anticorrosion treatment) Colour= As desierd by EIC Usage/Application-Ouldoor Waterproof:Yes

Ref. Item No. 35, Approved Tender ID 2022_DSDA_367956_1

Supplying, and installing of FRP made fibre circular swing for age group of 3 to 10 years children customized with MS Pillar material or frame work having specified dimension.Its need aftractive finish designs as well as beautiful color combinations which makes these highly preferred for use in park areas. The Manufacturer/supplier shall provide full details of the FRP materials, including all associated manufacturing processes, test certificates, adhesive, and fasteners. The Manufacturer/supplier shall responsible for all labour, materials, equipment, carriage and all other incidentals cost S0veTed Dys Sp8CficetiCntmariecUΦe F四 components in accordence with any structural drawings provided by the EIC. Body Material=FRP Supporting Material=MS(Steel Components all powder coated with FRP treatment) Colour= As desierd by EIC Usage/Application-Outdoor Waterproof:Yes

P.W.D (Roads)Page No.- 270/ Item No. - 8.07

Providing & fixing Concrete Sign Board as per IRC specification of size 900 x 750 x 37 mm. thick made with RCC 1:1½:3 with pakur variety stone chips reinforced with double layer IRC febric (75 x 75 mm. mesh) and fixed with necessary nuts & bolts on two RC precast posts 100 mm. x 150 mm. of height 2.65 m. of which top 750 mm. is of section 100 x 13 mm. and 1.90 metre above GL & 0.75 metre below GL including digging hole, repacking the same with cement concrete 1:3:6 with jhama khoa or with local stone chips etc. complete including painting two coats on both faces lettering sign marks etc. as per direction of the Engineer-in-Charge. (The rate is inclusive of cost of reinforcement, concrete, shuttering, nuts & bolts, washer etc. complete.)

Add 18% GST (Sl No. 1 to 19)

Add 1% Welfare Cess