Repair/ replacement to joinery flooring plastering sanitary fittings internal water supply and certain associated works at Sewar fort Bharatpur

Amount

M&L for Rendering 15 mm thick in CM 1:6 on stone masonry surfaces or surface other than fair face of brick-work complete all as specified.

All as above item no 2 but in CM 1:4 on fair faces finished even and smooth without using extra cement complete all as specified.

M&L for rendering 15 mm thick in CM (1:4) on fair faces of brick work ,finished fair & even Including taking down cement plaster of any description etc including racking out joints,hacking for key, scrubbing down with water complete all as specified .

Ditto as above item no 3 but in CM (1:6) on other fair surface finished even and smooth without using extra cement complete all as specified .

M & L Preparation of new plastered or un plastered surface of wall including cornices, pilasters etc by brooming down and applying two coats of distemper oil emulsion white or tinted over a coat of alkali resistant primer complete all as specified .

M&L Preparation of new plastered surfaces of walls and applying two coats of cement base paint over a coat of primer with hand roller complete all as specified .

M&L Preparation of newly plastered surfaces of Wall & applying three coats of white wash complete all as specified.

Demolition of brick masonry built in cement mortar or cement lime mortar including all quoins, arches, pillars etc but excluding ashlar facings,dressed stone work and precast concrete articles complete all as specified .

M&L Brick work with sub class 'B' old size bricks bricks straight or curved on plan exceeding 6 m mean radius built in cement mortar 1:6 complete all as specified .

All as per item No 09 but except bricks

Taking down chowkats or frames n. exc 1.5 sqm each with shutters (without taking off shutters from the frame) complete all as specified .

Taking down chowkats or frames exc 1.5 sqm but n exc 4 sqm each with shutters (without taking off shutters from the frame) complete all as specified.

Taking down shutter of any description area exc 1 sqm and n. exc 2 sqm

S&F for sollid PVC door frame of size 50mmx47mm made out of 5mm plain colour pvc sheeet reinforced with m.s. squre tube complete all as specified.

Supplying & fixing in the frames at site factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement complete all as specified and shown on drawing SSR part II 2020.

S&F 35 mm thick 2nd class hardwood factory made plain framed, panelled shutters (any No. of panels) with lock rail and panel of 9mm BWP commercial ply or 12 mm veneered particle board with commercial veneering on both faces the size of rail & stiles as per IS:1003 (Part-I) kiln seasoned and chemically pressure treated complete all as specified .

S&F 35 mm thick 2nd class hardwood factory made glazed and skeleton shutters open rebated and prepared to receive glass, gauge etc.( without sash bars ), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, gauge etc., sizes of members of shutters as specified in SSR Part I Section 8 clause 8.24 (a) complete all as specified .

M&L for rolled mild steel framed work such as grill grating etc with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors , laddres, door gate frame, framed baliusters, walk ways, railing , frame work of water tank and similar work conforming to Fe-290, Gde-E-165 complete all as specified .

S&F MS holdfast, hook and pintle hinges, large hasp and staples, clamps, hooks for hanging fans and similar small articles conforming to Fe-290 Gde E-165 including necessary welding etc. and fixed in position complete all as specified .

S&F 100 mm butt hinges medium weight cold rolled mild steel, ISI marked, fixed to angle iron chowkats including welding complete all as specified .

S&F 150 mm long mild steel barrel tower bolts stove enameled black with bright bolt (ISI marked) complete all as specified .

Mild steel pressed steel bow handle oval type stove enameled black of size 150 mm (ISI marked) complete all as specified .

S&F MS sliding door bolt, plate type, 300mm long, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts & nuts, 4 on bolt plate and 2 on staple plate and fixed complete all as specified .

S&F extruded aluminium alloy handle 150mm size fabricated type anodised, ISI marked complete all as specified .

S&F Aluminium anodised barrel tower bolt 150mm long of extruded section and fixed complete all as specified .

S&F 75 mm butt hinges medium weight cold rolled mild steel, ISI marked, fixed to angle iron chowkats including welding complete all as specified .

S&F for Factory made steel window with side hung shutteers including projecting type hinges with steel handle and steel peg stay complete with glazing bars dovetailed or welded complete all as specified .

All as per item No 27 above but without glazing bars complete all as specified .

M&L dismantling floor,hearth or wall tiling including cement mortar bedding (but not backing) , removing serviceable tiles to store and rubbish off the premises complete all as specified ..

M&L Glazed ceramic Tiles,in verticle surface 350X250X7mm/ 450X300X7mm set & jointed in neat cement sluury and pointed in white or colour cement to match the existing surface over and including 10mm thick rendering in CM 1:4 complete all as specified .

M&L for Coloured Non skid ceramic tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, set and jointed in neat cement slurry and pointed in coloured cement over & including 15mm thick rendering in CM 1:4.

M&L for coloured Glazed ceramic tiles in vertical surfaces of size 300mm x 200mm, 7mm thick , set and jointed in neat cement slurry and pointed in white or coloured cement to match the existing surface over and including 10mm thick rendering in CM 1:4 complete all as specified .

Demolition of cement concrete unreinforced in ground floor and paving n.exc 15 CM thickness (below or above GL) complete all as specified .

M&L Non - skid Ceramic colored tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc over 15 mm thick screed bed in CM 1:4 in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match complete all as specified .

M&L for 25mm thick plain cement concrete 1:2:4 type B-1 (20 MM graded aggregate ) as in sub base of flooring complete all as specified.

Dismantling of stone slab and tiles of any description or thickness in floors, etc. laid dry & laid dry in pointed complete all as specified .

M&L for Machine cut kota stone slab flooring 18-20 mm thick over & including cement screed 20 mm thick in cement mortar 1:6, laid and jointed with gray cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete.

M&L for Machine cut kota stone slab 12-15 mm thick in riser of steps, skirting, dedo and pillar laid over & including 15 mm thick rendering in cement mortar 1:4, laid and jointed with gray cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified .

Providing and fixing 20 mm thick gang saw cut, mirror polished, premoulded and prepolished,Granite of any colour and shade machine cut for kitchen platforms, vanity counters, window cills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/ stone work, including necessary holes for pillar taps etc. rubbing, cutting, moulding and polishing to edges to give high gloss finish etc. complete at all levels.

Dismantling stone slabs in roofs, suspended floors, chajjas, landings, etc., any thickness, jointed in any mortar complete all as specified .

M&L for sand stone slabs 7.5 cm thick in sun shades, lintel stone , shelves, cills, landings, cover stones, templates, etc. n. exc. 3 m in length, punched dressed on face and along exposed edges, self faced on other side and set in lime mortar 1:2 or cement mortar 1:4 complete all as specified .

Mirror polishing on marble/granite/kota stone/stone work required to give high gloss finish complete including necessary repair work & all necessary aggrangements complete all as specified.

S&F 3 mm thick plain sheet glass ordinary quality and glazing with oil putty in square not exceeding 0.5 in each pane including hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds glazed with putty or fixed with beads complete all as specified .

S&F for Sheet glass ordinary quality 3 mm thick and glazing with oil putty in square n. exc 0.50 sqm in each pane complete all as specified .

S&F Galvanised mild steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.00 mm and fixed with tinned tacks, or galvanised wire staples complete all as specified .

S&F repair bib tap, cast copper alloy, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule of 15 mm bore, complete all as specified .

S&F in repair brass ball valve, high pressure with polythene float and fly nut complete screwed for iron pipe or brass ferrule and fixed of 20mm bore, complete all as specified .

S&F in repair of pillar tap, cast copper alloy with capstan heads,chromium plated, fancy type screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks & fly nuts, screwed for iron pipes of 15mm bore complete all as specified .

Dismantling of interlocking tiles of any description , any thickness complete all as specified .

M&L 100 mm thick PCC 1:4:8 type D-2 (using 40mm graded aggregate) as in sub base/levelling for undulated part floor complete all as specified .

M&L for 60mm thick & M-35 factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould/rubber molded, laid in required colour & pattern over and including 25mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as specified .

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified .

S&F Rolled Mild Steel work as in post ,roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections,ms pipe) including distance pieces, cleats etc. conforming to Fe-410W Gde E-250 quality 'A' complete all as specified .

Excavating in post holes (or similar holes) each not exc 0.50 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers n.exc 25cm, watering, and removing surplus soil to a distance n.exc 50 m and making good surface in soft/ loose soil complete all as specified .

Dismantling Asbestos cement ( corrugated and semi corrugated) sheets in roof coverings complete all as specified .

M & L for Pre- painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 mpa as in roof covering / cladding to wall, fixed with self tapping screws complete all as specified .

M&L for preparation of new untreated steel surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified .

M & L prepration of new wood or wood based surface of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified .

M&L for one coats painting with synthetic enamel paint to old wood or wood based surfaces of any description, not otherwise described over 10 CM width or girth including preparation of surface complete all as specified.

M&L for one coats painting with synthetic enamel paint to old steel or steel based surfaces of any description, not otherwise described over 10 CM width or girth including preparation of surface complete all as specified

S&F of 500 ltr ISI marked three layer rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position & including 20mm brass ball valve Including dismantling of existing water tank of 500 Ltr capacity complete all as specified .

Demolition of PCC in roof covering, kerbs, roof kerbs, benching, coved fillets etc including old decayed water proofing treatment of any type all as specified & as directed (also including the rate for disposal of building rubbish/ malba of dismantled or waste material collected after demolition of existing treatment & dumping for lead upto 1km for all lifts) complete all as specified .

M&L for 40mm thick PCC 1:2:4 type B-1(using 20mm graded stone aggregate) in roof covering , benching , etc & finished even and rough complete all as specified .

Supply only water proofing compound ISI marked complete all as specified .

S&F APP based polymeric membrane not less than 3mm thick, weighing not less than 3.5 Kg/sqm , reinforced with polyster non-woven fabric (weighing not less than 150 gm/sqm and upper side of membrane thermally insulated with white mineral gravel finish, informaly embadded during manufacturing process shall only be used. It shall be laid by torch application,side overlaps shall be 75mm and the ends shall be 100mm and all over laps shall be sealed by torch application including applying a coat of cold applied bitumen primer conforming IS:[email protected]/sqm & applied a Hot blown coat of bitumen layer spread over primer @ 1.0 Kg/Sqm complete all as specified .

M& L for cement concrete tiles 20cm x 20cm x 20mm thick, machine pressed, set jointed and pointed in neat cement slurry with grey cement withhout pigment in floors, and cut and polished over & including 15mm thick screed bed in CM 1:4 (mixed with WPC ) complete all as specified. Note: WPC shall be measured and paid seprately.

S&F in repair Brass Chromium plated central hole basin including mixer with fixed spout complete all as specified .(Make;- Kerovit Catologue No :KB711026 or equivalent in Jaquar parryware .)

M&L for PVC connection 15 mm size with PTMT nuts of length 600 mm complete all as specified .

S&F for in repair Brass Chromium plated long body Bib cock with wall flange complete all specified. (Make;- ESSCO cat part no APR 105107 or equivalent in Jaquar parryware complete all as specified .

S&F in repair Brass Chromium plated Angular stop cock with wall flange complete all specified. (Make;- ESSCO cat part no APR 101053 or equivalent in Jaquar parryware complete all as specified .

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete all as specified .

25 mm bore

20 mm bore

S&F in repair viterous china Table Top Basin with CP waste coupling, Size: 500x420x120mm complete all as specifies (Make;- Jaquar Registered design FLS-WHT-5935 or equivalent in Hindware ,perryware complete all as specified .

S&F in repair for PVC wall panelling with panel of 300 mm x 6 mm Hollow section of Sintex pattern SPUF- 146 or equivalent , fixed with PVC plug and screw and inserted to next panel groove, edges and corners of all door/ window/openings etc to be covered with PVC angel fixed with solvent cement complete all as specified .

Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double action hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, complete all as specified . Note:- Rate of Door Handle ,Lock & door closer etc deemed to be in quoted rate )

S&F toughened glass of approved make and brand of 10mm thick coloured /tinted /smoke / clear glass for partition using glazing clips & cleats and special metal sash putty alongwith all fixings and fixtures. complete all as specified.

Repair and maint to aluminium door & window shutters alongwith necessary fittings and fixtures such as hinges ,rubber washer ,rubber seal ,aluminium beadings ,door lock,handle etc all as specified.

S&F 5.5 mm thick plain sheet glass ordinary quality and glazing with oil putty in square exceeding 0.5 in each pane including hacking out old broken glass (any thickness, size, quality or description) from wooden frames ,alum frame or stone, concrete or brick surrounds glazed with putty or fixed with beads complete all as specified .

S &F 18mm thick solid PVC ply of first quality of one side prelaminated of approved colour and one side white colour fixed with screw 'solvent cement/adhesive to make cupboard shutter complete all as specified .Make : Rajshree/Sintex or equivalent make approved

S &F 18mm thick solid PVC ply of first quality of both side white colour fixed with screw 'solvent cement/adhesive to make shelves, partitions and drawers etc for kitchen cabinet and cupboards complete all as specified . Make : Rajshree/Sintex or equivalent approved make .

S & F stainless steel handle of 110mm size of best quality as per approved sample complete all as specified.

S & F magnet catch for kitchen cabinet shutter as per approved sample complete all as specified .

S & F colour powder coated mild steel continuous (piano) hinge, width of flaps(when open) is 30mm complete all as specified.

S&F in repair Single piece-WC with UF Soft Close Slim Seat Cover, Fixing Accessories, Accessories set and Cistern Fittings, Size: 370x670x720 mm, S Trap-220mm complete all as specified . (Make;- Jaquar design R LYS-WHT-38851S220UFSMN or equivalent in Hindware Parryware)

Providing and fixing in white vitreous china Large ISI Urinal SIze of 382x398x601 mm (Make Kerovit Catologue No :Rasso (isi) Model No-KS507 in Perryware ,Hindware equivalent )and sizes respectively with with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required complete all as specified .

Supply and fixing in repair anodized snap grid frame work of size 605mm x 605 mm for false ceiling including necessary notching. The snap grid shall consist of anodized aluminium main & cross tee of size 36.5 x 25 x 1.4 mm weighing 0.24 Kg/RM and 23.5 x 26.4 x 1.40 mm weighing 0.191 Kg/RM respectively. The main and cross tee shall be jointed at junction crossing with anodized aluminum angle bracket of size 15mm x 15mm x 1.5 mm weighing 0.12 Kg/RM fixed with suitable MS bolts, nuts and washer. The snap grid (main/cross tee section) shall be supported at ends all along the wall with anodized aluminum angle of size 40 x 25 x 2 mm weighing 0.36 Kg/RM fixed to wall with suitable arrangement and providing 12 mm thick mineral fibre board of make Armstrong in fixed in grid support with 6.0 mm dia plain mild steel wire galvanised class 3 fixed in detached works etc to support snap grid, made of aluminum as per specification complete all as specified .

VASUNDHARA AND COMPANY

M/S MAMTA CONSTRUCTIONS

M/s Gupta Traders

B R ENTERPRISES

M/s Ranaji Construction Co

PD GUPTA AND COMPANY

MS Kumar and Brothers

krishna Associate