Construction of Degree College at Silli in Ranchi District under Ranchi University, Ranchi

Amount

Earth Work in excavation in Foundation Trenches in Ordinary soil (vide classification of soil item -B) and disposal of excavated earth as obtained to a distance upto 50 M including all lift, leveling ramming the foundation trenches, removing roots of tree shrubs all complete as per approved design, building specification and direction of E/I

Extra for earth work in hard soil as per specification & direction of engineer in charge (Vide classification of soil item B)

Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width aswell as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-incharge. Hard rock (requirin g blasting).

Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete.

Supplying and Filling in plinth with local sand and under floors including,watering, ramming consolidating and dressing complete.

Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diaMTR.er holes and plugging with cement mortar 1:2 (1 cement : 2 Coarse sand) to match the existing floor

Earth filling in foundation trenches and plinth in layer not exceeding 150mm thick will watered rammed fully compacted and fine dressed with earth obtained from excavation of foundation trenched with a lead of 50mm and lift of 1.5M all complete as per building specification and direction of E/I. (Mode of measurement compacted volume).

Providing coarse clean local SAND IN FILLING in foundation trenches or in plinth including ramming and watering in layer not exceeding 150 mm thick with all leads and 1.5 M lifts including cost of all materials, labours, royalty and taxes all complete as per building specification and direction of Engineer In charge (Mode of measurement compacted volume)

Providing and laying damp-proof course 50mm thick with cement concrete 1: 2:4 (1 cement : 2 Coarse sand (zone-iii) : 4 graded stone aggregate 20mm nominal size ).

Providing designation 75 B one brick flat soling joints filled with local sand including cost of watering taxes royalty all complete as per building specification and direction of E/l.

Clearing grass and removal of rubbish up to a distance of 50 meters outside the periphery of the area

Supplying, filling, spreading & leveling gravels of size range 5 mm to 10 mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.

Brick work with common burnt clay F.P.S. (non modular ) bricks of class designation 7.5 in foundation and plinth in:Cement mortar 1:6 (1 cement : 6 coarse sand)

CONCRETE WORK

Providing and laying in position cement concete of soecified grade excluding the cost of centering and shuttering - All work up tp plinth level

Providing and laying cement concrete in kerbs, steps and the like at or near ground level excluding the cost of centering, shuttering and finishing. 1:1½:3 (1 Cement: 1½ coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).

1:4:8 (1 cement :4 coarse sand (Zone -III) :8 graded stone aggregrate 40 mm normial size)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:2:4 (1 Cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 40 mm nominal size)

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.

Supplying, filling, spreading & leveling stone boulders of size range 5 cm to 20 cm, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.

R C C WORK

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix including pumping of concrete to site of layinh but excluding the cost of centering ,shuttering finishing and reinforcement including admixtures in recommended proportions as per IS : 9103 to accelerate rated srtting of concrete, improve workability without impaiting strenth and durability as per direction of engineer in charge (note :- Cement content considered in this item is 330 kg/cum excess/ less cement used as per design mix is payable/ recoverable seperataly ).

All works upto plinth level

All works above plinth level upto floor V level

Add for using extra cement in the items of design mix over and above the specified cement content therein.

Providing Tor steel reinforcement of 8mm. dia. rods as per approved design and drawing excluding carriage of M.S. bars to work site , cutting, bending and binding with annealed wire with cost of wire, removal of rust placing the rods in position all complete as per building specification and direction of E/l. (TMT Fe 500 (only vailid for TATA (TISCON), SAIL, JSPL, Electro steel Limited Bokaro and Vizal steel(RINL))

Providing Tor steel reinforcement of 10mm.,28mm and 32mm dia dia. rods as per approved design and drawing excluding carriage of M.S. bars to work site , cutting, bending and binding with annealed wire with cost of wire, removal of rust placing the rods in position all complete as per building specification and direction of E/l. (TMT Fe 500 (only vailid for TATA (TISCON), SAIL, JSPL, Electro steel Limited Bokaro and Vizal steel(RINL))

Providing Tor steel reinforcement of 12mm. 16mm,20mm and 25mm dia. rods as per approved design and drawing excluding carriage of M.S. bars to work site , cutting, bending and binding with annealed wire with cost of wire, removal of rust placing the rods in position all complete as per building specification and direction of E/l. (TMT Fe 500 (only vailid for TATA (TISCON), SAIL, JSPL, Electro steel Limited Bokaro and Vizal steel(RINL))

Centering and shutteing including struting, propping etc and removal of form for

Foundations, footings, bases for columns, etc for mass concrete

Centering and shuttering including strutting, propping etc. and removal of form for Foundations, footings, bases of columns, etc.

Reinforced cement concrete work in wall (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillers, piers, abutments, posts and struts etc. upto floor five level excluding cost of centring, shuttering, finishing and reinforcemnet.1:1.5:3 (1 cement : 1.5 coarse sand: 3 graded stone aggregate 20mm nominal size)

Walls ( any thickness) including attached pilasters, butteresses, plinth and string course etc

Suspended floors, roof , landings , balconies and access platform

Lintels, beams, plinth beams, girders, bressumers and cantilevers plinth beam

Columns, Pillars, Piers, abutments, Posts and struts

Stairs, ( excluding landings ) expept sprial staircase

Vertical and horizontal fins individuaaly or forming box louvers band, facies and eaves boards

Extra for additional height in centering, shuttering where ever required with adequate bracing, propping etc., including cost of de-shuttering and decentering at all levels, over a height of 3.5 m, for every additional height of 1 metre or part thereof (Plan area to be measured). uspended floors, roofs, landing, beams and balconies (Plan area to be measured)All floors slabs:( floor to floor Ht 3.6 m)

Providing and fixing of Glass Fiber Reinforced Concrete (GFRC) Cornice in approved size, pattern, Design, thickness and color. The Cornice should be made From 53 grade white Portland cement/ 43 grade OPC or PPC gray cement manufactured by J.K. Cement or equivalent having minimum compressive Strength of 40N/mSQM, Quartz, Fine Silica Sand, Alkali Resistant Glass Fiber manufactured by Sant Gobain, Owens corning or equivalent, super plasticizers and polymers manufactured by BASF, Sika, MYK Schomburg or equivalent. The material casting should take place in Synthetic Rubber / FRP Mould manufactured by Reckli or equivalent. The Fixing of Column should be Dry Fixing i.e. to be done with MS Frames, Stainless Steel (SS-304)/dash fasteners, Self-screw and pins.

BRICK WORK

providing designation 75 B brickwork in C M ('1 :6 ) in foundation and Plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10 mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth, curing. taxes and royalty all complete as per building specification and direction of E/l.

Providing designation 75A brick work in CM (1:6) in superstructure with approved quality of clean coarse & of F.M. 2.5 including providing 10mm thick mortar joints cost of screening, racking out joints to 15mm depth, curing, taxes and royalty all complete as per building specification and direction of E/I.

Providing designation 100A brick work with flyash lime brick (FLAG) confirming to IS 12894-1990 (9"x4.5"x3") in C.M. (1:6) in foundation and plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar joints costs of screening materials, raking out joints to 15mm depth curing taxes and royalty all complete as per building specification and direction of E/I.

Providing designation 75A brickwork in CM (1:3) in superstructure with approved quality of clean coarse sand of FM 2 to 2,5 including providing 10mm thick mortar joints , cost of screening, materials, scaffolding, raking out joints to 15mm depth curing, taxes and royalty all complete as building specification and direction of E/I

Providing Designation 100A B/W with Fly Ash Lime Brick (FALB) conforming to IS 12894-1990 (9"x4.5"x3") in cement mortar (1:6) in Superstructure with clean coarse sand of F.M. 2 to 2.5 including 10mm thick mortar joints,cost of screening, raking out joints to 15 mm depth, curing, taxes and royalty all complete as per building specification and direction of E/l.

Providing designation 112 mm thick reinforced designation 100 A brick work vuith fly ash lirne brick (FLAG)confirming to lS 12894-1990 (9"x4'5"x3" ) in C.M. ( 1 . 4 ) in superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including the cost of screening, carriage of materials,n caffolding, raking out joints to 15mm depth, curing, taxes and royalty (but excluding the cost of reinforcement) all complete as per building specificationand direction of E/|.

Extra for providing & placing in position 2 no 6mm dia ms bar every 3rd corse of half brick masonary

Providing and laying of brick bats including cost of material, labour charges etc complete as per specification & E/IUnder Floor Brick flat soling area by PLINE

Providing designation 75 B one brick flat soling joints filled with local sand including cost of watering taxes royalty all complete as per building specification & direction of E/I

WOOD WORK

Supplying, fiiting and fixing good quality, well dressed and well seasoned sal wood work in chaukhat in doors windows skylights fanlights and C/W celetial window opening including wedge over all clamps complete including application of two coats of wood preservative of approved quility onthe surface buttling walls and lintels all complete as per building specification anddirection of E/I.

Supplying fitting and fixing 35mm thick solid core type non-decorative single leaf flush shutter door and windows with black board core blended with high quality phenol formal clehydes synihetic resin both side commercial veneered of standard make with Aluminium fittings :such as hinges, tower bolts, hendle, cleats and sand blocks and laxes all conrplete as pe building specrfication and direction of E/l.

Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conformingto IS : 2046 Type S, including cost of adhesive of approved quality.9.127.2 1.0 mm thick

Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured).

Extra for cutting rebate in flush door shutters (Total area of the shutter to be measured).

Supplying, fitting and fixing 35mm thick solid core type decorative single leaf flush door shutter with one sides teak decorative and another side commercial veneered with black board core bended with high quality phenol formal dehydes synthetic resin of standard make with Aluminium fittings such as hinges, tower bolts, handle, cleats and sand blocks and taxes all complete as per building specification and direction of E/l.

Supplying fitting and fixing 35mm thick solid core type decorative double leaf flush door sltutter with both side decorative veneered with black board core bended with high quality phenol formal clehydes synihetic resin of standard make with Aluminium fittings :such as hinges, tower bolts, hendle, cleats and sand blocks and laxes all conrplete as pe building specrfication and direction of E/l.

Providing, fitting and fixing oxidised iron fitting of approved quality and make to door and window all complete as per building specification and direction of E/I necessary screws etc. complete.

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid door/window/clerestory windows & desertory other Frames/Chowkhat comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modulus of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with M.S hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-In- Charge. (M.S hold fast/lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimensions i.e depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

Frame size 45 x 70 mm

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid board one side white color and other side of board laminted with PVC foil of minimum 14 micron thickness of approved design pasted with hot melt adhesive for cup boards, work stations and bathroom/kitchen cabinet etc. of required sizes comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/ mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/ borer proof, water/moisture proof and fire retardant and fixing with stainless steel piano hinges/soft close clip on concealed hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge. (Note: stainless steel piano hinges/soft close clip on concealed hinges and necessary S.S screws shall be paid separately)

25 mm thick

Providing and fixing wooden moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surface etc. complete : 50*12mm

Providing and fixing bright finished brass 100 mm mortice latch and lock, ISI marked, with six levers and a pair of anodised (anodic coating not less than grade AC 10 as per IS : 1868) aluminium lever handles of approved quality with necessary screws etc. complete.

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete.

Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete.

Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg, for doors, including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge.With stainless steel cover plate minimum 1.25 mm thickness glass door

Providing and fixing glazing in door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge. (Cost of aluminium snap beading shall be paid in basic item):

Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge (Door handle, lock and stopper etc.to be paid separately).12 mm thick frameless toughened glass door

Polishing in high gloss/matt finish melamine clear polish on wood work in required color/wooden shade texture with following process in the sequence as detailed below: 1. The surface to be polished is rubbed with sand paper 80/ 120 no. and then with sand paper of 160/180 nos. 2. Applying two coats of sealer with spray gun and allowing sufficient drying time for 1st coat and 2nd coat is allowed to dry for 8 to 12 hrs. 3. On drying of sealer coat, wet rubbing with emery cloth of finer grading with ample water to remove excess sealer layer and make the surface further smooth after this wet rubbing, then surface is applied with special grade melamine fillers to fill all the small and big holes/grooves etc. Filler coat to be allowed to dry for 4 to 6 hrs on which again a light wet rubbing is done this surface is further allowed to dry for 12 hrs. 4. On this, 1st coat of melamine polish is applied with spray gun using melamine clear polish and melamine thinner in required proportion. This 1st coat is allowed to dry for 24 hrs then this dry surface is again fine wet rubbed smooth, which is further allowed to dry for 12 hrs. The final melamine polish is applied with compressor pressure spray gun using melamine clear polish and melamine thinner mixed in required proportion complete as per direction of Engineer-in-Charge. (Final coat to be done in 1 or 2 layers without gap of time.)

Providing and fixing S.S. sliding door bolts (aldrop) with nuts and screws etc. complete:

Providing and fixing SS sliding tower bolt with required fastners (Screws) complete:

Providing and fixing SS handles "D" type with required fastners (Screws) complete:

250x19 mm (Pipe dia)

200x19 mm (Pipe dia)

Providing and fixing SS hanging floor door stopper with necessary screws etc.complete:

150 mm Rubber Stopper

Providing and fixing SS door latch with necessary screws etc. complete.

Providing and fixing SS sliding baby latch with required fastners (Screws) complete:

Providing & Fixing Wall mounted door Buffer

Providing and fixing fire resistant door frame of section 50 x 60 mm on horizontal side & 35 x 60 mm on vertical sides having built in rebate made out of 1.6 mm thick GI sheet ( Zinc coating not less than 120gm/m²) suitable for mounting 120 min Fire Rated Glazed Door Shutters. The frame shall be filled with Mineral wool Insulation having density min 96Kg/m³ . The frame will have a provision of G.I. Anchor fastners 14 nos ( 5 each on vertical style & 4 on horizontal style of size M10 x 80 ) suitable for fixing in the opening along with Factory made Template for SS Ball Bearing Hinges of Size 100x89x3mm for fixing of fire rated glazed shutter. The frame shall be finished with a approved fire resistant primer or Powder coating of not less than 30 micron in desired shade as per the directions of Engineer - in- charge . (Cost of SS ball bearing hinges is excluded).

Providing and fixing 60 mm thick glazed fire resistant door shutters of 120 min Fire Rating confirming to IS:3614 (Part II) or EN1634-1:1999, tested and certified as per laboratory approved by Engineer-in-charge, with suitable mounting on door frame, consisting of vertical styles, top rail & side rail 60 mm x 60 mm wide and bottom rail of 110 mm x 60 mm made out of 1.6mm thick G.I. sheet (zinc coating not less than 120gm/m²) duly filled mineral wool insulation having density min 96 kg/ m³ and fixing with necessary stainless steel ball bearing hinges of size 100x89x3mm of approved make, including applying a coat of approved fire resistant primer or powder coating not less than 30 micron etc all complete as per direction of Engineer-in-charge (paneling to be paid for separately).

Providing and fixing panic bar / latch (Double point) fitted with a single body, Trim Latch & Lock on back side of the Panic Latch of reputed brand and manufacture to be approved by the Engineer- in- charge, all complete.

Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge:Fixing with adjustable lugs with split end tail to each jamb

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:30 mm thick including ISI marked Stainless Steel butt hinges with all acesories (handle, lock, door closer, stopper etc. as per dwg)

STEEL WORK

Supplying, fitting and fixing M.S. grill gate with M.S. grills made of 20x6mm M.S. flats or 16mm square bars fitted on 25x25x6mm M.S Angle frame including cost of fabrication , providing necessary locking arrangement with haskal and domny duly fixed in P.C.C. (1:2:4) blocks of required size, applying a priming red lead paint over steel work, taxes all complete as per drawing specification and direction of E/l. (where steel is not supplied by the deptt.)

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.

Providing and fixing hand rail by welding etc. to steel ladder railings & staircases railing including applying a priming coat of approved steel primer

Providing and fixing 1 mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3mm MS gusset plates at the junction and corners.all necessary fittings completejncluding applying a priming coat of approved steel primer.Using M.S. angle 40x40x6 mm for diagonal braces

Supplying,fitting and fixing M.S. grill made of 20x6cmm M.S. flat as per approved design and drawing, properly fabrlcated with joints continuous fillet welded and finished smooth, carriage of grill to work site, hoisting as per building specification and direction of E/1

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Providing corrugated G.S. sheet roofing including vertical / curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required..80 mm thick with zinc coating not less than 275 gm/m²

Providing and fixing 15 cm wide, 45 cm overall semi-circular plain G.S. sheet gutter with iron brackets 40x3mm size, bolts, nuts and washers etc., including making necessary connections with rain water pipes complete.

Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60 mm thickness,including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge:

Fixing with carbon steel galvanised dash fastener of required dia and size (to be paid for separately

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).SS Tube TAKEN 15 KG /SQM

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid .in basic item):

With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm)

Providing and fixing factory made upvc glazed/wire mesh window/ door comprising of lead free upvc multi -chambered frame, sash and mullion/ coupler (where ever required ) extruded profiles having minimum wall thickness of 1.70 mm series R1 and R2 profiles and 2.10 mm for series R3 and R4 profile confirming to EN 12608 in any shape colour and design duly reinforced with galvanized mild stell section made of required shape & size as per CPWD specification upc extruded glazing beads interlock and inline sash adaptor (where ever required ) of appropriate dimansion, EPDM gasket, hardwere, SS 304 grade fastners of minimum 8 mm dia with countersunk head comprising if matching polyamide PA6 IS 1367 Part 1 to 14 plastic packers plastic caps and nacessary stainless steel screws etc. profile of frame sash & mullion (if requred ) shall be mitred cut and fusion welded/ mechanically jointed duly sealed at all corners inculding drilling of holes for fixing hardware and driange of water etc. after fixing frame the gap between frame and adjaent finished wall shall be filled with weather proof silicon sealant over backer rod of approved size and quility, all complete as per approved drawing confirminh to cpwd specification & direction of engineer in charge. section of steel reinfocement and cross sections of upvc profiles to be as per design approved by engineer in charge. wire mesh/ glazing of plain/ toughened /laminated/ double glass unit with / without high performance coating as per design requirements and confiming to IS 3548 & IS 16231 shall be paid separately.

Note:- structural design proof checked from a government engineering institude to be provided by the manufacturer for : i) sites with basic wind speed Greater then 45m/ sec as per IS 875 - part 3 ii) sites with structure height more then 20m for all wind speeds

Two track two panels sliding door with alumnium channel for roller track, wool pile, zinc alloy (zamak) powder coated handle on every panel along with multi point locking systed, adjustable nylon rollers with SS 304 body. Using R3 Series with frame (55 mm & above ) X (40mm & above ) &sash ( 30 mm & above )x (75mm X above ). (height upto 2.5metre)

Three track three panel sliding door with two gazed & one wire mesh panels with aluminium channel for roller track, wool pile, zinc alloy (zamak) podwer coated handle on two panels a;ong with multi point locking system adjustable nylon rollers with SS304 Body.Using R3 Series with frame (98 mm & above ) X (40mm & above ) &both glazed and fly screen sash ( 30 mm & above )x (74mm X above ). (height upto 2.5metre)

Three track three panels sliding window with aluminium channel for rollar track, wool pile nylon rollers with SS 304 body.Using R4 series with frame ( 115 mm & abovex (45 mm & above ) & sash (44 mm & aboove )x ( 55 mm & above ) with zinc alloy (zamak) powder coated handle on every panel along with multu point lockingh system (height above 1.8m).

Two track two panels sliding window with aluminium channel for roller track, wool pile, nylon rollers with SS304 body.Using R4 series with frame ( 115 mm & abovex (45 mm & above ) & sash (44 mm & aboove )x ( 55 mm & above ) with zinc alloy (zamak) powder coated handle on every panel along with multu point lockingh system (height above 1.8m).

Providing and fixing 1 mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3mm MS gusset plates at the junction and corners.all necessary fittings completejncluding applying a priming coat of approved steel primer.Using M.S. angle 40x40x6 mm for diagonal braces

FLOORING WORK

Chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard, jointed with neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc. complete, on 20 mm thick bed of cement mortar 1:4 (1 cement: 4 coarse sand).

Providing and laying Vitrified tiles in different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS: 15622, of approved brand & manufacturer, in all colours and shade, in skirting, riser of steps, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately).specification and direction of E/I. 800 x 800 mm size

providing and laying, Doublecharge vitrified floor tiles in different sizes (thickness to be specified by lhe manufacturer) with water absorption less than 0.08% and conforming to lS 15622/ISO 13009 of approved make in all cotours and shades, laid on 20mm thick cement mortar 1 4 (1 cement:4 coarse sand) jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete Size of tile 600x600 mm

Providing and fixing granite 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for flooring, kitchen platforms, vanity counters, window sills , facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.

Providing edge moulding to 18 mm thick marble/granite stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge.

Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete.

Providing and fixing stone slab with table rubbed, edges rounded and polished, of size 75x50 cm deep and 1.8 cm thick, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-in-charge and finished smooth.Granite Stone of approved shade

Providing and laying 15 mm - 23 mm thick kotah stone slab flooring of approved size, texture and colour over 19mm thick base of lime morter (1:1:1) (lime putty : surkhi: coarse sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing to granolithic finish with approved quality of carborandum stone including cost of curing, taxes and royalty all complete as per building specification and direction of E/I.600*600MM SIZE

Providing and laying 25 mm thick kotah stone tiles in risers of steps, skirting and pillars of approved size, texture and colour laid over 12mm thick cement mortar (1:3) and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing to granolithic finish with approved quality of carborandum stone including cost of curing, taxes and royalty all complete as per building specification and direction of E/I.

Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick Cement Mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including pointing the joints with white cement and matching pigments etc., complete.

Providing and laying 6mm precast white glazed tiles in walls over 12mm cement mortar (1 : 3) and jointed with grey cement slurry flush pointed with white cement including rubbing, polishing and cost of curing taxes, and royalty all complete as per building specificaton and directon and E/I.

Stone tile (polished) work for wall lining over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and cement slurry @ 3.3 kg/SQM including pointing in white cement complete. Granite of any colour and shade

Providing 50mm thick cement concrete flooring (1:2:4) with 20mm to 6mm size grade stone chips finish with flooring coat of neat cement in panels including cost of curing, finishing the surface smooth by rubbing with carborandum stone, taxes & royality with all complete as building specification and direction of E/I

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.With commercial grade colour tiles

Marble stone flooring with 18 mm thick marble stone, as per sample of marble approved by Engineer-in-charge, over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with grey cement slurry, including rubbing and polishing complete with :Udaipur green marble

Green stone 20 -25 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete.

ROOFING & WATER PROOFING WORK

Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design :

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete.

Water proofrng for Old and New Roof Slab :- Providing and laying waterprooflng treatment on roof slab by applying two Component, factory a designed ready to use, acrylic modified flexible,material applied with brush, roller or spray for wate proof i n g coating as per manufactlrer specificatio With following steps :-

(a)surface preparation :-Provrding and cleaning of concrete surface to remove dLrst, oil, grease including removal of existing loose paint / coating, and cement laitance by cleaning with compressed air & water jet including all materials, labour, tools complete. Ponding test to be done after plugging all outlets and to be checked from sofftt to identify seepage, leakage. On identiiication of seepage, cement grouting to be done with non shrink expanding admixture of Sika lndia Pvt.Ltd. / MYK Schomberg / Dr Fixit/Fosroc or equrivallent. Providing and reparing of all corners and joinis such as those betr,veen the parapet wall and the roof slab etc shall be chamfered with '150mm X '150 mm fillet of mortar (Cement: sand - 1:4) admixed with acrylic polymer of Sika/ Fosroc/MYK Schomberg/Dr Fixit or equivalent Before chamfering a prime coat shall be given with the sl u rry ?!gc!ylic polyrner Repai rin g su rface irreg ularities, damaged concretein base slab, dead cracks if any, with an acrylic polymer modilied repair moriar ir;cluding a coat of bonding agent of the same with ceme nt slurry rncluding all rnaterial, labour, tools complete.

(b)1st Coat :- Apply 1st coat of two component acrylic modified, ready to use, llexrble cementitious material on surface saturated dry roof and inside wall of Parapet wall upto 600 mm by brush or roller. After 1st coat of application ,45 gsm oI Fibre glass cloth to lay when the first layer is still green. 1st coat should be applied @1.50 kg/SqmUcoat For the fJUrpose of n'ieasurernent tite entire treated surface will be measured."

(c) :2nd Cr:ai :-T,: apply the 2nd coat of two component acrylic modified, reatiy to-use, flexible cementttious material right angle to the '1st coat over the glass fibre liad surface. 2nd coat should be applied @0.7 kgl Sqrnt/coat. For the pltrpose of measurement the entire treated surface will be rneasurecl." Alte r three days of drying the 2nd coat, therainwater ouilets to be plugged and ponding test to be done for 48 hours to rrjerrtify se epage, leal<age from soffit and if found necessary rectification lo be plugged and ponding test to be done for 48 hours to identify seepage, leakage from soffit and if found necessary rectifcation to be done as per satrsfaction of E/C protected from damage before screed over it. Watqr proofing Brand:*Sika Topseal 109hi / Fosroc Brushbond RFX/ Dr Fixit Pidiffin 2Kl MYK Aqraiin TG Product Performance - Chemical Base Part A. Acrylic copolmer, Part B Specially graded cementitious powder - Density 1.6 l.rg/l (mixcd density) at +27oC Tensile Strength - 2 lllmm2 after 28 clays (with Fibre cloth) (According to ASTM D 2370)Prillcut Bond Streric;tl-r '-2 I'J/mm2 (concrete lajlqry) (Aqgcrdlglq ISO 4624) Slant-Shear Bond Strength -4 N/mm2 (According to FIP 5.'15) Elongation at Break -35% without Fibre Cloth and 20% wilh Fibre Clot (Accordrng to ASTM D 2370)

(d) Protection of treated surface with PCC- The treated surface should be covered with 25mm/50mm PCC of M-20 grade(1:1.5:3) with proper slope ( '1:120) towards tlre rain outlets in alternatepanels of 2 mt x 2mt keeping 6 mrn gap betuieen the panel joint. lntegralwater proofing admixture conforming to lS 2645 @ of 100 ml per bag of of cement to be added in the scree d concrete(pard separately for thts ltems).-All corners shall be charrmfered with 150mm X 150 mm fillet. The rainwater outlets shall be just leveled with the screed concrete to ensure smooth discharge of water - the peripheral gaps between pvc pipe outlet and concrete surface slrould be packed properly with rich concrete and the peripheral mouih to be sealed with moisture insensitive epoxy putty of Sika lndia Pvt.Ltd / IVIYK Schomberg / Dr FixiUFosroc .For the purpose ofrreasurement the entire treated surface will be measured."

(e) Groove of PCC surface should be filled with Polysulphide Sealant (Paid Separately) Brand - Sika lndia Pvt Ltd / MYK Schomberg / Dr Fixit/Fosroc Warranty for Five years.

Covering of treated surface wrth PCC :- Providing 50mm thick Cementn Concrete M20(1:'1.5:3) r'naintaining slope in alternate 2 mIx 2 mt panels with aaproved quality of stone chips of 20 mm to 6 mm size graded and clcaned sand of F M 2 5 io 3 including screening,shuttering,and mixing cerite nt c0ncrete in mixer with admixture of integral water proofing and placing rn position,strikirrg cLrring,t-a]glgnd royality all complete as per buildirrg specifictionJand direction of E/l.Panels that has been left should be casteci nextday.-lhere should be 6 mm gap between Panels.Brand- Sika *Plastocrate plus,MYK proof WP10, Fosroc- Conplast X421ic , Dr Frx,t Prdiproof LWr

Providing and mixing Liquid lntergral water proofing compound in Conctrete or plaster as per rnanufacturer specificatioqand as per cjirection of Eng - in Charge Brand- Sika Plastocrate plus, MYK proof WP 1 0, Fosroc-Cc.rnplast X4211 C, Dr fixit Pidiproof LW+ or Equivalent

Providing and filling of 6 mm groove between 50mm PCC panels with 6 mm thick deep thermocol strip and filling the rest 25mm with polysulphide sealant (poring grade)as per drawing and technical specification and direction of E in charge (with 18 % GST ). Brand:- sika - polysulshide,fosroc- thioflex 600, dr fixit pidi seal PS (42P) ,MYK seal PS or euivalent.

Toilet/Kitchen Water proofing:

1) Surface preparation by grinding machine, cleaning , crack filling etc. complete

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying :

(a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours.

(b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry

Roof/Terrace Water proofing:

Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations:

(a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment.

(b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs.

(c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineerin-charge

(d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineerin-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep

(e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test. All above operations to be done in order and as directed and specified by the Engineer-in-Charge : With average thickness of 120 mm and minimum thickness at khurra as 65 mm.

FINISHING WORK

Providing 12mm thick cement plaster (1:6) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per specification and direction of E/I.

Providing 6mm thick cement plaster (1:4) in ceiling with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per specification and direction of E/I.

12mm cement plaster 1:4 (1 cement: 4 coarse sand) finished with a floating coat of neat cement

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete

Providing 19 mm thick water proof cement plaster (1:3) with clean coarse sand of F.M. 1.5with 5% cico or any other approved water proofing compoundincluding taxes and royalty all complete as per building specification and direction of E/l.

Finishing walls with textured exterior paint of required shade : New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm

Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) Same as external plaster 50%

Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications :Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of Special primer applied @ 0.75 ltr /10 sqm

Providing two coats of oil bound distemper of approved shade and make ov er a coat of cement primer over new surface including preparing the plastered surface by rubbing smooth with purnice stone or fine sand paper applying putty taxes all complete as per building specification and direction of E/I.Two coats

Providing two coats of snowcem of approved shade and make over a coat of cement primer on new surface including preparing the plastered surface smooth with sand paper, scaffolding, curing and taxes all complete as per building specification and direction of E/l.

Wall painting with acrylic emulsion paint, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour.Two coats

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :

Extra for plastering exterior walls of height more than 10 m from ground level for every additional height of 3 m or part thereof.

Painting with synthetic enamel paint of approved brand & manufacture to give an even shade:

Providing two coats of synthetic enamel paint of approved shade and make over steel surface including cleaning the surface thoroughly, scaffolding and taxes all complete as per building specification and direciton of E/l.

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade:

ALUMINIUM & GLASS WORK

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately):

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately)

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):

With float glass panes of 4 mm thickness (weight not less than 10 kg/sqm)

With float glass panes of 4 mm thickness (weight not less than 12.5 kg/sqm)

Providing and fixing fly proof stainless steel grade 304 wire gauge, to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia. 0.50 mm all complete. With 12 mm mild steel U beading

1-Sturcture Glazing

Providing and supplying aluminium extruded tubular and other aluminium sections as per the architectural drawings and approved shop drawings , the aluminium quality as per grade 6063 T5 or T6 as per BS 1474,including super durable powder coating of 60-80 microns conforming to AAMA 2604 of required colour and shade as approved by the Engineer-in-Charge. ( The item includes cost of material such as cleats, sleeves, screws etc. necessary for fabrication of extruded aluminium frame work. Nothing extra shall be paid on this account). The weight of aluminium extruded section shall be taken for purpose of payment.For opnable portion

Designing, fabricating, testing, protection, installing and fixing in position semi (grid) unitized system of structural glazing (with open joints) for linear as well as curvilinear portions of the building for all heights and all levels including:

Structural analysis & design and preparation of shop drawings for the specified design loads conforming to IS 875 part III (the system must passed the proof test at 1.5 times design wind pressure without any failure), including functional design of the aluminum sections for fixing glazing panels of various thicknesses, aluminium cleats, sleeves and splice plates etc. gaskets, screws, toggles, nuts, bolts, clamps etc., structural and weather silicone sealants, flashings, fire stop (barrier)-cum-smoke seals, microwave cured EPDM gaskets for water tightness, pressure equalisation & drainage and protection against fire hazard including:

(b) Fabricating and supplying serrated M.S. hot dip galvanised / Aluminium alloy of 6005 T5 brackets of required sizes, sections and profiles etc. to accommodate 3 Dimentional movement for achieving perfect verticality and fixing structural glazing system rigidly to the RCC/ masonry/structural steel framework of building structure using stainless steel anchor fasteners/ bolts, nylon seperator to prevent bimetallic contacts with nuts and washers etc. of stainless steel grade 316, of the required capacity and in required numbers.

(c) Providing and filling, two part pump filled, structural silicone sealant and one part weather silicone sealant compatible with the structural silicone sealant of required bite size in a clean and controlled factory / work shop environment, including double sided spacer tape, setting blocks and backer rod, all of approved grade, brand and manufacture, as per the approved sealant design, within and all around the perimeter for holding glass.

(d) Providing and fixing in position flashings of solid aluminium sheet 1 mm thick and of sizes, shapes and profiles, as required as per the site conditions, to seal the gap between the building structure and all its interfaces with curtain glazing to make it watertight.

(e) Making provision for drainage of moisture/ water that enters the curtain glazing system to make it watertight, by incorporatingprinciples of pressure equalization, providing suitable gutter profiles at bottom (if required), making necessary holes of required sizes and of required numbers etc. complete. This item includes cost of all inputs of designing, labour for fabricating and installation of aluminium grid, installation of glazed units, T&P, scaffolding and other incidental charges including wastages etc., enabling temporary structures and services, cranes or cradles etc. as described above and as specified. The item includes the cost of getting all the structural and functional design including shop drawings checked by a structural designer, dully approved by Engineer-in-charge. The item also includes the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working structural glazing as specified, cleaning and protection till the handing over of the building for occupation. In the end, the Contractor shall provide a water tight structural glazing having all the performance characteristics etc. all complete as required, as per the Architectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the Engineer- in-Charge.

Note:- 1. The cost of providing extruded aluminium frames, shadow boxes, extruded aluminium section capping for fixing in the grooves of the curtain glazing and vermin proof stainless steel wire mesh shall be paid for separately under relevant items under this subhead. However, for the purpose of payment, only the actual area of structural glazing (including width of grooves) on the external face shall be measured in sqm. up to two decimal places

Note:-2. The following performance test are to be conducted on structural glazing system if area of structural glazing exceeds 2500 Sqm from the certified laboratories accreditated by NABL(National Accreditation Board for Testing and Calibration Laboratories), Department of Science & Technologies, India. Cost of testing is payable separately.

The NIT approving authority will decide the necessity of testing on the basis of cost of the work, cost of the test and importance of the work. Performance Testing of Structural glazing system Tests to be conducted in the NABL accredited lab or by any other accreditation body which operates in accordance with ISO / IEC 17011 and accredits labs as per ISO/ IEC 17025.

(1). Performance Laboratory Test for Air Leakage Test (-50pa to - 300pa) & (+50pa to +300pa) as per ASTM E-283-04 testing method for a range of testing limit 1 to 200 mVhr. (2) Static Water Penetration Test. (50pa to 1500p) as per ASTME- 331-09 testing method for a range up to 2000 ml. (3) Dynamic Water Penetration (50pa to 1500pa) as per AAMA 501.01- 05 testing method for a range upto 2000 ml. (4) Structural Performance Deflection and deformation by static air pressure test (1.5 times design wind pressure without any failure) as per ASTME-330-10 testing method for a range upto 50 mm. (5) Seismic Movement Test (upto 30 mm) as per AAMA 501.4- 09 testing method for Qualitative test, Tests to be conducted on site. (6) Onsite Test for Water Leakage for a pressure range 50 kpa to 240 kpa (35psi) upto 2000 ml

Providing and fixing SGU 6mm Annealed glass in aluminium/uPVc windows, ventilators and partition etc. including providing EPDM gasket, perforated aluminium spacers, desiccants, sealant (Both primary and secondary sealant) etc. as per specifications, drawings and direction of Engineer-in-charge complete.The Properties of glass should be as : Solar heat gain Cofficiant (HSGC) =0.50 and Visual Light Transmission (VLT) =50% or more and shade to be approved by EIC/Architect.

Extra for openable side / top hung vision glass panels (IGUs) including providing and supplying at site all accessories and hardwares for the openable panels as specified and of the approved make such as heavy duty stainless steel friction hinges, min 4 -point cremone locking sets with stainless steel plates, handles, buffers etc. including necessary stainless steel screws/ fasteners, nuts, bolts, washers etc. all complete as per the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineer- in-Charge.

Filling the gap in between aluminium/ stone/ wood frame and adjacent RCC/Brick/ Stone/ wood/ Ceramic/ Gypsum work by providing weather/structural non sag elastomeric PU sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete, complying to ASTM C920, DIN 18540- F & ISO 11600 Upto 10 mm depth and 10 mm width

Providing corrugated G.S. sheet roofing including vertical / curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.0.80 mm thick with zinc coating not less than 275 gm/m²

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with :

12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with BIS certification marks)

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

Providing and Fixing 15 mm thick densified tegular edged eco friendly light weight calcium silicate false ceiling tiles of approved texture of size 595 x 595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanised steel sections (galvanising @ 120 grams per sqm including both side) consisting of main ‘T’ runner suitably spaced at joints to get required length and of size 24x38 mm made from 0.33 mm thick (minimum) sheet, spaced 1200 mm centre to centre, and cross “T” of size 24x28 mm made out of 0.33 mm (Minimum) sheet, 1200 mm long spaced between main’T’ at 600 mm centre to centre to form a grid of 1200x600 mm and secondary cross ‘T’ of length 600 mm and size 24 x28 mm made of 0.33 mm thick (Minimum) sheet to be inter locked at middle of the 1200x 600 mm panel to from grid of size 600x600 mm, resting on periphery walls /partitions on a Perimeter wall angle pre-coated steel of size(24x24X3000 mm made of 0.40 mm thick (minimum) sheet with the help of rawl plugs at 450 mm centre to centre with 25 mm long dry wall screws @ 230 mm interval and laying 15 mm thick densified edges calicum silicate ceiling tiles of approved texture in the grid, including, cutting/ making opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc., wherever required. Main ‘T’ runners to be suspended from ceiling using G.I. slotted cleats of size 25x35x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm G.I. adjustable rods with galvanised steel level clips of size 85 x 30 x 0.8 mm, spaced at 1200 mm centre to centre along main ‘T’, bottom exposed with 24 mm of all Tsections shall be pre-painted with polyster baked paint, for all heights, as per specifications, drawings and as directed by Engineer-in-Charge

Designing, fabricating, testing, installing and fixing in position Curtain Wall with Aluminium Composite Panel Cladding, with open grooves for linear as well as curvilinear portions of the building , for all heights and all levels etc. including: (a) Structural analysis & design and preparation of shop drawings for pressure equalisation or rain screen principle as required, proper drainage of water to make it watertight including checking of all the structural and functional design. (b) Providing, fabricating and supplying and fixing panels of aluminium composite panel cladding in pan shape in metalic colour of approved shades made out of 4mm thick aluminium composite panel material consisting of 3mm thick FR grade mineral core sandwiched between two Aluminium sheets (each 0.5mm thick). The aluminium composite panel cladding sheet shall be coil coated, with Kynar 500 based PVDF / Lumiflon based fluoropolymer resin coating of approved colour and shade on face # 1 and polymer (Service) coating on face # 2 as specified using stainless steel screws, nuts, bolts, washers, cleats, weather silicone sealant, backer rods etc. (c) The fastening brackets of Aluminium alloy 6005 T5 / MS with Hot Dip Galvanised with serrations and serrated washers to arrest the wind load movement, fasteners, SS 316 Pins and anchor bolts of approved make in SS 316, Nylon separators to prevent bi-metallic contacts all complete required to perform as per specification and drawing The item includes cost of all material & labour component, the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working curtain wall with aluminium composite panel cladding, cleaning and protection of the curtain wall with aluminium composite panel cladding till the handing over of the building for occupation. Base frame work for ACP cladding is payable under the relevant aluminium item.s The Contractor shall provide curtain wall with aluminium composite panel cladding, having all the performance characteristics all complete , as per the Architectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the Engineer-in-Charge. However, for the purpose of payment, only the actual area on the external face of the curtain wall with Aluminum Composite Panel Cladding (including width of groove) shall be measured in sqm. up to two decimal places.

Providing and making cove in gypsum board. false ceiling with all accessories.as per drawing and instructions of Engineer in charge .

Providing and fixing of Glass Fiber Reinforced Concrete (GFRC) Screen with borders 50mm thick and inner portion 35mm thick in approved size, pattern, Design, thickness and color. The Screen should be made From 53 grade white Portland cement/ 43 grade OPC or PPC gray cement manufactured by J.K. Cement or equivalent having minimum compressive Strength of 40N/mSQM, Quartz, Fine Silica Sand, Alkali Resistant Glass Fiber manufactured by Sant Gobain,Owens corning or equivalent, super plasticizers and polymers manufactured by BASF, Sika, MYK Schomburg or equivalent. The material casting should take place in Synthetic Rubber / FRP Mould manufactured by Reckli or equivalent. The Fixing of Column should be Dry Fixing i.e. to be done with MS Frames, Stainless Steel (SS-304)/dash fasteners, Self-screw and pins.

SH: MISCELLANEOUS WORK

Providing and fixing at or near ground level precast cement concrete in kerbs, edgings etc. as per approved pattern and setting In position with cement mortar 1:3 (1 Cement : 3 coarse sand), including the cost of required centering, shuttering complete.

Providing and laying 500x500x40 mm thick Turf paver (Turfpave XD) on 150 mm thick sub grade of compacted bed of 20 mm thick nominal size stone aggregate and base course and filling with 150 mm thick jamuna sand, including spreading, well ramming, consolidating and finishing smooth etc. all complete as per direction of Engineer-in-charge

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.

Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge. 60mm thick cement concrete paver block of M-35 grade with approved colour, design & pattern.

Providing and fixing of Glass Fiber Reinforced Concrete (GFRC) Column in approved size, pattern, Design, thickness and color. The Column should be made From 53 grade white Portland cement/ 43 grade OPC or PPC gray cement manufactured by J.K. Cement or equivalent having minimum compressive Strength of 40N/mSQM, Quartz, Fine Silica Sand, Alkali Resistant Glass Fiber manufactured by Sant Gobain, Owens corning or equivalent, super plasticizers and polymers manufactured by BASF, Sika, MYK Schomburg or equivalent. The material casting should take place in Synthetic Rubber / FRP Mould manufactured by Reckli or equivalent. The Fixing of Column should be Dry Fixing i.e. to be done with MS Frames, Stainless Steel (SS-304)/dash fasteners, Self-screw and pins.GFRC Column (35-40 mm thick) as per design with GFRC capitals

Providing and fixing of Glass Fiber Reinforced Concrete (GFRC) Cornice in approved size, pattern, Design, thickness and color. The Cornice should be made From 53 grade white Portland cement/ 43 grade OPC or PPC gray cement manufactured by J.K. Cement or equivalent having minimum compressive Strength of 40N/mSQM, Quartz, Fine Silica Sand, Alkali Resistant Glass Fiber manufactured by Sant Gobain, Owens corning or equivalent, super plasticizers and polymers manufactured by BASF, Sika, MYK Schomburg or equivalent. The material casting should take place in Synthetic Rubber / FRP Mould manufactured by Reckli or equivalent. The Fixing of Column should be Dry Fixing i.e. to be done with MS Frames, Stainless Steel (SS-304)/dash fasteners, Self-screw and pins. GFRC Cornice (30mm thick) as per your design

Providing and fixing of Glass Fiber Reinforced Concrete (GFRC) Screen with borders 50mm thick and inner portion 35mm thick in approved size, pattern, Design, thickness and color. The Screen should be made From 53 grade white Portland cement/ 43 grade OPC or PPC gray cement manufactured by J.K. Cement or equivalent having minimum compressive Strength of 40N/mSQM, Quartz, Fine Silica Sand, Alkali Resistant Glass Fiber manufactured by Sant Gobain,Owens corning or equivalent, super plasticizers and polymers manufactured by BASF, Sika, MYK Schomburg or equivalent. The material casting should take place in Synthetic Rubber / FRP Mould manufactured by Reckli or equivalent. The Fixing of Column should be Dry Fixing i.e. to be done with / MS Frames, Stainless Steel (SS-304) dash fasteners, Self-screw and pins.

20 Passenger Lift/ 1360Kgs / 1.25 Speed / 6 Floors / 6 Stops / Stainless Steel (1.5 Mm) Car Cabin

20 Passenger Lift/ 1360Kgs / 1.25 Speed / 3 Floors / 3 Stops / Stainless Steel (1.5 Mm) Car Cabin

16 Passenger Lift/ 1088Kgs / 1.25 Speed / 6 Floors / 6 Stops / Stainless Steel (1.5 Mm) Car Cabin

Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earth with lead upto 50 metres.

Plant mix method (Construction of granular sub-base by providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per clause 401) (ii) Rate per cum for grading-II Material

Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge. 80 mm thick C.C. paver block of M-35 grade with approved color design and pattern.

Providing and laying 60mm thick factory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with line sand etc. all omplete as per the direction of Engineer-in-charge.

Providing Retro-reflective regulatory sign board of size 900 mm dia meter made out of 2 mm thick aluminium sheet, face to be fully covered with high intensity encapsulated lens type retro -reflective sheeting as approved by Engineer-in-charge . Letter, symbols, borders etc. will be as per IRC - 67 with required colour scheme onthe boards and with the high intensity grade A. The aluminium sheet to be riveted to M.S. frame of angle iron of size 40x40x4 mm. The boards will be fixed to 1 No. 50x50 mm square post made of M.S. angle 50x50x4 mm, 4 m long welded to the frame with adequate anti-theft arrangement .Sheet work to be painted with two or more coats of synthetic enamel paint over an under coat (primer) and back side of aluminium sheet to be painted with two or more coats of epoxy paint including appropriate priming coat complete in all respects as per direction of Engineer-in-charge.

Providing and fixing in position pre-cast R.C.C. manhole cover and frame of required shape and approved quality Rectangular shape 600x450 mm internal dimensions

12 mm cement plaster finished with a floating coat of neat cement of mix : 1:3 (1 cement: 3 fine sand)

Supply and Installation of Precast Concrete Reinforced Square Cement Flower Pots Material - Cement Shape (When viewed from Top) Square Artistic /Decorative work on Pots Yes Pot Length (mm) 18 inch Pot Width (mm) 18 inch Pot Height (mm) 18.5 inch

Supply and Installation of Precast Concrete Reinforced Bench M-30 Grade concrete mix in accordance with IS : 10269/Latest in gray cement by using vibro - compaction technique and with reinforcement as detailed in Govng. specn. ach seating plank ( bottom ) of bench bolted with leg by help of 12 mm dia. X 65 mm length galvanized steel countersunk bolts with EVA washer – Backrest planks fitted with half threaded carriage bolts and nuts of size 165 mm X 8 mm dia with EVA & steel washer Seat / plank length ± 3 mm = 1500MM Seat height ± 3 mm = 450 MM Seat width ± 3 mm = 440 MM

CARRAIGE OF MATERIALS

SAND (UPTO 10KM LEAD)

CHIPS (UPTO 22KM LEAD)

BRICKS (UPTO 8KM LEAD)

Matel (UPTO 22 KM LEAD)

Plumbing

SCHEDULE ITEMS (JSOR 2022)

Providing and fixing male ended 15 mm dia brass bib cock of approved quality ( wt not less than 350 gms ) with extra socket all complete as per specification and direction of E/l .

Providing and fixing 15 mm dia male ended C.I .Body brass spindle valve and seat bib cock of approved quality (wt not less than 400 gms ) with extra socket all complete as per specification and direction of E/l .

Providing and fixing brass / C.I. Stop cock of approved quality all complete as per specification and direction of E/l .A) BRASS STOP COCK

(a) 15 mm dia

(b) 20 mm dia

Providing and fixing 15 mm dia and 45 cm. long P. V .C connection pipe with heavy quality brass coupling at both ends etc. all complete as per specification and direction of E/l .

Providing and fixing 15mm size C.P brass pillar cock (Weight not less than 350 gms) C.I body brass spindle pillar cock of approved quality as per spcification and direction of E/l.(b) C.I. body brass spindle

Providing and fixing Gun metal full way valve of approved qualtiy, all complete as per specification and direction of E/l

(A) 15mm dia wt not less than 400 gms

(b) 20mm dia wt not less than 400 gms

(c) 25 mm dia wt not less than 500 gms

(d) 32 mm dia wt not less than 700 gms

(e) 40 mm dia wt not less than 1kg

(f) 50 mm dia wt not less than 1.5 kg

Cutting drain width wise above G.L for laying G.I pipes and restoring with brick in cement mortar (1:4) 12mm cement plaster in (1:4) with neat cement punning as per specification and direction of E/l

Cutting chajja or cornice for laying G.I pipe and restoring the same with R.C.C (1:2:4) brick work in cement mortar (1:4) and cement plaster (1:4) as per specification and direction of E/l.

Supplying, fitting and fixing the following items complete with all materials as per specification and direction of E/l.a) Mirrors of 6 mm thick plate glass bevelled edge mirror including C.P brass revolving fittings, 3 mm plywood board and C P hinges to fix with mirror

(1)600x450 mm size

(2) C.P brass liquid shop container

Supplying, fitting and fixing 40 mm high viterous white glazed earthen ware E.W.C. with "p" trap of Parry Hindustan or any other I.S.S. make including supplying & fixing 15 litres C.I. mosquito proof low down flushing cistern of approved make with complete fittings with C.I. handle and R.S. or bracket with telescopic flush pipe with brass coupling and plumbers joints spindle stop cock of approved quality weight not less than 450 grms. , 15 mm P.V.C. alkathene pipe 45 cm long with brass coupling at both ends and white/ black plastic solid state seal and lead of commander/ cuckoo or other I.S.S. make with hinges or screw etc. painting pipe and cistern etc. with 2 coats of approved paint over a coat of red oxide primer etc. all complete as per specification and direction of E/l.

(a)12.5 lit. low level P.V.C. cistern

Supplying fitting and fixing white glazed fire’s clay sink of approved make with overflow arrangements supported on C.I. or R.S. painted brackets 40mm. dia C.P.brass waste with C.P.brass chain and rubber plug 40 mm dia P.V.C. waste pipe about 750mm long with brass coupling at one endand 15mm C.I. body brass spindle bib cock of approved quality of weight not less than 450grams. including cutting wall and making good the same etc. all complete as per specification and direction of E/I. Kitchen sink 600mm ×450mm×250mm.

Making holes in wall for laying H.C.I, pipe and restoring the same after pipe laying as per specification and direction of E/l.(i) 125 mm dia

Supplying Submersible pump sets confirming to IS 8034 and motor cvonfirming to IS 9283. Pump shall be suitable for various delivery head and discharge with stainless steel pump shaft ant polypropylene/ norylimpeller. Motor suitable for working on 415 V+10%, 3PH, 50 HZ, AC supply with cable guard, thurst carbon/ fibre bearing to withstand entire hydraulic thrust, water proof winding shall be provided. The pump ste shall be suitable for direct coupling. Pump shall have suitable outlet as per manufacturers design. Anti thrust stream lined no return valve shall be provided with pump. 3 m submersible copper conductor cable in single/ double run shall be provided with each pump.

Submersible pump set 50mm dia (with polypropylene/ Noryl Impeller) up to 20 stages 3 HP

Excavating trenches of required width for pipe, cables etc including excavation for sockets ,& dressing of sides ,ramming of bottoms ,depth upto 1.5m including getting out the excavated soil,& then returning the soil as required, in layers not exceeding 20 cm in depth including consolidating each deposited layer by ramming ,watering, etc and disposing of surplus excavated soil as directed, within lead of 50m.

All kinds of soil

Pipes, cables etc. exceeding 80 mm dia. But not exceeding 300 mm dia

Extra for excavating trenches for pipes, cables etc. in all kinds of soil for depth exceeding 1.5 m, but not exceeding 3 m. (Rate is over corresponding basic item for depth upto 1.5 metre).

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required :

Kitchen sink with drain board 510x1040 mm bowl depth 250 mm

Providing and fixing toilet paper holder :C.P. brass

Providing and fixing PTMT Bottle Trap for Wash basin and sink.

Bottle trap 31mm single piece moulded with height of 270 mm, effective length of tail pipe 260 mm from the centre of the waste coupling, 77 mm breadth with 25 mm minimum water seal, weighing not less than 260 gms

Bottle trap 38 mm single piece moulded with height of 270 mm, effective length of tail pipe 260 mm from the centre of the waste coupling, 77 mm breadth with 25 mm minimum water seal, weighing not less than 263 gms

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.

FLEXIBLE PIPE32 mm dia

40 mm dia

Providing and fixing toilet paper holder :

C.P. brass

Providing and fixing C.P. Brass extension nipple (size 15mmx50mm) of approved make and quality as per direction of Engineer-in-charge.

Providing and fixing on wall face unplasticised - Rigid PVC rain water pipes confirming to IS : 13592 Type A including jointing with seal ring confirming to IS : 5382 leaving 10mm gap for thermal expansion.110mm dia

Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised - Rigid PVC rain water pipes confirming to IS : 13592 Type A including jointing with seal ring confirming to IS : 5382 leaving 10mm gap for thermal expansion.

Coupler 110 mm dia

Single Tee with door 110x110x110 mm

Bend 87.5 deg 110 mm

Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised - Rigid PVC rain water pipes confirming to IS : 13592 Type A including jointing with seal ring confirming to IS : 5382 leaving 10mm gap for thermal expansion.

Shoe (Plain) 110 mm Shoe

Providing and fixing unplasticised- PVC pipe clip of approved desing to unplasticised - PVC rain water pipes by means of 50x50x50mm hard wood plugs, screwes with M.S. Screw of required length including cutting brick work and fixing in cement mortar 1:4 ( 1 Cement : 4 Coarse sand ) and making good the wall etc. complete.

110mm dia

Providing and fixing white vitreous china battery based infrared sensor operated urinal of appx.size 610x390x370mm having pre & post flushing with water (250ml & 500ml consumption) having water inlet from back side,including fixing to wall with suitable brackets all as per manufacturers specification & direction of Engineer-in charge.

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end):

65 mm nominal bore

80 mm nominal bore

Providing and fixing C.P. bass angle valve of approved quality conforming to I.S:8931.15 mm nominal bore

Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15cm diameter and weighting not less than 440 grams.

Providing and fixing wash basin with CI brackets,15mm brass pillar taps,32mm CP brass waste of standard pattern, including painting of fittings and brackets,cutting and making good the walls wherever required.

White vitreous china wash basin size 630 mm x 450 mm with a single 15mm CP brass pillar tap.

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete.

Providing and fixing G.I. pipes conforming to I:S including all fittings, testing, cutting holes or chases and making good where required. (For waste connections) 32mm dia

Providing and laying Non pressure NP 2 class (light duty) RCC pipe with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1cement : 2 fine sand) including testing of joints etc. complete.

150 mm. dia. RCC Pipes

250 mm. dia. RCC Pipes

300 mm. dia. RCC Pipes

Construction brick masonry manhole in cement mortar 1:4 (1 cement : 4 coarse sand) RCC top slab with 1:2:4 mix (1 cement : 2 coarse sand 4 graded stone aggregate 20mm nominal size) foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design.

Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) :

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Inside size 120x90 cm and 90 cm deep including C.I. cover with frame (medium duty) 500 mm internal diameter, total weight of cover and frame to be not less than 116 kg weight of cover 58 kg and weight of frame 58 kg) :

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Extra for depth for manholes Size 90x80 cm

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Size 120x90 cm

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Constructing brick masonry circular type manhole 0.91 m internal dia at bottom and 0.56m dia at top in cement mortar 1:4 (1 cement : 4 coarse sand), inside cement plaster 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement, foundation concrete 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size), and making necessary channel in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement, all complete as per standard design :

0.91 m deep with S.F.R.C. cover and frame (heavy duty, HD-20 grade designation) 560 mm internal diameter conforming to I.S. 12592, total weight of cover and frame to be not less than 182 kg., fixed in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) including centering, shuttering all complete. (Excavation, foot rests and 12mm thick cement plaster at the external surface shall be paid for separately) :

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Extra depth for circular type manhole 0.91m internal dia (at bottom) beyond 0.91 m to 1.67 m

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Constructing brick masonry circular manhole 1.22 m internal dia at bottom and 0.56 m dia at top in cement mortar 1:4 (1 cement :4 coarse sand) inside cement plaster 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement foundation concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) and making necessary channel in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement, all complete as per standard design :

1.68 m deep with SFRC Cover and frame (heavy duty HD 20 grade designation) 560 mm internal diameter conform ing to I.S. 12592, total weight of cover and frame to be not less than 182 kg. fixed in cement concrete 1:2:4 (1 ce ment : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) including centering, shuttering all complete. (Excavation, foot rests and 12 mm thick cement plaster at the external surface shall be paid for separately) :

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Extra depth for circular type manhole 1.22 m internal dia (at bottom) beyond 1.68 m to 2.29 m :

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS : 10910, on 12 mm dia steel bar conforming to IS: 1786, having minimum cross section as 23 mmx25 mm and over all minimum length 263 mm and width as 165 mm with minimum 112 mm space between protruded legs having 2 mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and having manufacture's permanent identification mark to be visible even after fixing, including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) complete as per design.

Providing and fixing square mouth SW gully trap class SP-1 complete CI grating brick masonry chamber and water tight CI cover with frame of 300 x 300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.7 kg. as per standard design.

100x100mm size P type With common burnt clay F.P.S (non modular) bricks of class designation 7.5.

Constructing brick masonry road gully chamber 50 X 45 X 60 cm with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) including 500 X 450 mm precast R.C.C. horizontal grating with frame complete as per standard design :

With common burnt clay F.P.S (non modular) bricks of class designation 7.5.

Boring/drilling bore well of required dia for casing / strainer pipe, by suitable method prescribed in IS:2800 (part-1) including collecting samples from different strata, preparing and submitting strata chart/bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of engineer-in-charge, upto 90 metre depth below ground level.

All types of soil

300mm dia

Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS : 12818, including hire & labour charges, fittings & accessories etc, all complete, for all depths, as per direction of engineer-in-charge.

100mm nominal size dia

Supplying & filling, sepreading & leveling stone boulders of size range 5cm to 20cm, in the recharge pit, in the required thickness, for all leads & lifts, all complete, for all depths, as per direction of engineer-in-charge.

Supplying & filling, sepreading & leveling gravels of size range 5mm to 10mm, in the recharge pit, over the existing layer of boulders, in the required thickness, for all leads & lifts, all complete, as per direction of engineer-in-charge.

Supplying & filling, sepreading & leveling coarse sand of size range 1.5mm to 20mm, in the recharge pit, in the required thickness over gravel layer, for all leads & lifts, all complete, as per direction of engineer-in-charge.

Providing and fixing Bail plug / Bottom plub of required dia to the bottom of pipe assembly of tubewell as per IS : 2800 (part -1)

100mm dia

Providing and fixing in position pre-cast RCC manhole cover and frame of required shape & approved quality

EHD -35 Circular shape 560 mm internal dia

Providing and fixing G.I. pipes conforming to I:S including all fittings, testing, cutting holes or chases and making good where required. (For waste connections)

32mm dia

Painting G.I. pipes and fittings with synthetic enamel white paint with two coats over a ready mixed priming coat, both of approved quality for new work :

32mm dia

Providing and fixing PTMT grating of approved quality and colour.

Circular type

100 mm nominal dia

150 mm nominal size square 100 mm diameter of the inner hinged round grating

PLUMBING SYSTEM-NON SCHEDULE ITEMS

Providing fixing, testing and commissioning in position SWR PVC PIPE TYPE-B pipe comforming to IS:13592 including all fittings such as bends, junctions, inspection doors, offests, cowl, access pieces/clean out plugs, clamps /supports/ hangers etc. jointing with PVC Adhesive joints including cutting holes in walls, core cutting in slabs and making good the same. all complete as per specification and direction of E/l.

(a) 150 mm dia

(c) 100 mm dia

(e) 50 mm dia

(f) 25 mm dia

(g)250 mm dia

Providing & fixing in position uPVC P"or S" trap of self cleaning design of following sizes for the embedded areas. Making proper connection with drip-seal joints, cutting chase / hole in floors /slabs and bringing the same in proper condition in cement concrete 1:2:4 mix complete as required. including cost of cutting and making good the walls and floors where required.

3 x 50 mm inlet and 100 mm outlet (Multi Floor Trap)

50 mm outlet (Floor Drain)

Providing & fixing in position storage type hot water electrical geyser (vertical or horizontal-1.5 kw) including making connection in all respects.-Venus/Racold make.

25 litres capacity (Make: AO Smith or equivalent)

Supply installation testing and commissioning R.O.water purifier comprising 5 micron filter and UV steriliser on cold water supply to work on single phase 230 volts 50 HZ AC power supply with capacity 100 lph.-Kent/approved equal make.

Fixing of Wall Mounted C.P. Brass Single lever Sink Mixer with swinging spout of required size including cuttinig and making good the wall wherever required. (Make: Jaquar Sink Mixer CQT-23309 or equivalent)

Providing & fixing C.P. hand spray with lever control (health faucet) and flexible hose 1 m long connection with C.P. holder for hand spray complete in all respects as per direction of Engineer-Incharge. (Make: Jaquar, Hand Shower (Health Faucet) ALD-CHR-573 or equivalent )

Providing & fixing chinaware urinal partition of 160X 400X 825 mm with fixed with expandable anchor fasteners with C.P. brass bolts and washers, embedded in wall with anchor and set in cement concrete complete including cutting and making good the walls wherever required (Make: Parryware, white C0507 Large or equivalent)

Providing & fixing soild state no touch operating fully highgenic SS hand drier of best quality, to be operated with 230 volts, single phase, with fully hygienic condition, with all accessories including cutting and making good the walls, wherever required. (Make:- Euronics, Stainless Steel Hand Dryer EH21 or equivalent)

Providing and Fixing in position Hindware make or equivalent CP Grab Bar with wall flanges 600 mm to wooden cleats with C.P. brass screws complete in all respects.

Providing and fixing C.P. brass twin coat hooks fixed on toilet door with including CP brass screws, washers rawl plugh etc. complete in all respact. (Make: Jaquar, ACN-SSF-1161N or equivalent)

Supplying and fixing 100 mm dia SWR PVC End Cap (Clean Outlet Plug) fittings of approved make. all complete as per specification and direction of E/l.

Providing & fixing horizontal centrifugal pumps for domestic water lifting with CI casing bronze impeller suitable for operation on 400 / 440 V pH 50 cycle A/C power supply.Cost shall include electrical control panel (star/dol starter) with all controls to make the pumps to operate automaticaly.Sequencing shall be provided for the pumps.Pumps shall start /stop automatically depanding upon water level in overhead tank.

Domestic Water Supply at Water Supply Pump Room l - Set of Two Pumps (1 Working+ 1 Standby), Capacity -1.5 LPS, Head - 50 M., HP - 2.0 HP Approxi.

Hyd. System for Flushing Water Supply at STP Pump Rm - Set of Two Pumps (1 Working+ 1 Standby), Capacity -1.0 LPS, Head -50 M., HP - 1.5 HP Approxi.

Domestic Water Supply at terrace, 1- Set of Two Pumps (1 Working+ 1 Standby), Capacity -3.0 LPS, Head - 50 M., HP - 3.5 HP Approxi.

Flushing Water Supply at STP Pump Rm - Set of Two Pumps (1 Working+ 1 Standby), Capacity -2.5 LPS, Head -50 M., HP - 3.0 HP Approxi.

Providing & fixing horizontal centrifugal pumps for domestic water lifting with CI casing bronze impeller suitable for operation on 400 / 440 V pH 50 cycle A/C power supply.Cost shall include electrical control panel (star/dol starter) with all controls to make the pumps to operate automaticaly.Sequencing shall be provided for the pumps.Pumps shall start /stop automatically depanding upon water level in overhead tank.

Domestic water Pumps inlet

Location - Transfer pump to Terrace from pump room

Capacity 2.77 LPS each

Head 55 Mts

HP(appx) - 3.5

Pumps & associated works as described above

Filter Feed Pump FROM RAW WATER TO DOMESTIC WATER TRANSFER PUMP )

Location - Pump room

Capacity 1.5 LPS each

Head 25 Mts

HP(appx) - 1.5

Pumps & associated works as described above

Providing & fixing horizontal centrifugal pumps for domestic water lifting with CI casing bronze impeller suitable for operation on 400 / 440 V pH 50 cycle A/C power supply.Cost shall include electrical control panel (star/dol starter) with all controls to make the pumps to operate automaticaly.Sequencing shall be provided for the pumps.Pumps shall start /stop automatically depanding upon water level in overhead tank.

Domestic water Pumps inlet

Location - Transfer pump to Terrace from pump room

Capacity 1.0 LPS each

Head 30 Mts

HP(appx) - 1.5

Pumps & associated works as described above

Providing & fixing horizontal centrifugal pumps for flushing water lifting with CI casing bronze impeller suitable for operation on 400 / 440 V pH 50 cycle A/C power supply.Cost shall include electrical control panel (star/dol starter) with all controls to make the pumps to operate automaticaly.Sequencing shall be provided for the pumps.Pumps shall start /stop automatically depanding upon water level in overhead tank.

Flushing water lifting Pumps

Location - Inside pump room

Capacity 2.0 LPS each

Head 40 Mts

HP(appx) - 2.0

Pumps & associated works as described above

Sump Pump Providing and fixing compact monoblock dry motor submersible pumps of suitable rating, with non-clog free flow open impeller, suitable for operation on 415 volts +10% , 3 Phase, 50Hz, A.C supply, speed 2900 RPM including oil chamber, guide wire for lifting & lowering of pump, M.S. galvanized lifting chain, duck foot bend complete. The pump sets shall be supplied with required accessories & as per specification with the following :

Complete inlet, outlet and header piping of suitable dia (velocity shall not exceed 1.5m/s) -- 1 Lot

Butterfly valve and Dual Plate NRV of appropriate dia and rating - 1 Lot

Necessary cables from pump sets to pump starter panel - 1 Lot

Electrical control panel having all necessary accessories & safety devices of standard specifications and suitable for receiving incomer cable to connect complete. (Panels with sump pumps near each sump as per site conditions). -- 1 No.

Discharge :5 m3/Hr

Head : 25 m

Solid Handling : 50 mm

Pumps shall be operated on cyclic timing

The entire system along with pumps & control panel must be sourced from single manufacturer only for unit responsibility.

One set consist of 2 nos.of pumps - 1 working & 1 stand by (Complete set as above with 2 nos. pumps including cost for valves, piping, Control Panel and Cabling, Level Controllers, pressure gauges etc as required and as specified)

MULTIGRADE SAND FILTER (For Domestic Water Supply)Supply, assembly, erection, testing & commissioning of vertical M.S. Dual Media filter fabricated from 6mm thick M.S plate shell and 8mm thick M.S. plate dished ends with 3mm non-toxic, non-leaching rubber lining (rubber lining to be tested for pin-holes by spark tester) inside complete with initial charge of filter media activated carbon, face piping (GI, C Class), diaphragm/ball/non-return valves, accessories, painting, testing and commissioning of any under drainage system as required, complete. (Tested to 10 kg/sq cm)

Capacity : 1.5 lps

Filtration rate : 18-20 M³/M²/hr

Max. operating pressure : 3.5 Kg/Sq.cm

Test pressure : 5.5 Kg/Sq.cm

Supply, assembly, erection, testing & commissioning of vertical M.S. Activated Carbon filter fabricated from 6mm thick M.S plate shell and 8mm thick M.S. plate dished ends with 3mm non-toxic, non-leaching rubber lining (rubber lining to be tested for pin-holes by spark tester) inside complete with initial charge of filter media activated carbon, face piping (GI, C Class), diaphragm/ball/non-return valves, accessories, painting, testing and commissioning of any under drainage system as required, complete. (Tested to 10 kg/sq cm)

Capacity : 1.5 lps

Filtration rate : 15-17 M³/M²/hr

Max. operating pressure : 3.5 kg/Sq.cm

Test pressure : 5.5 Kg/Sq.cm

Supplying, assembly, erection, testing and commissioning of magnetic level sensors and controllers, CPVC probe tube, PP actuating float and all other equipment required for the performance of the system to the satisfaction of the engineer in charge complete including providing and fixing wiring from control junction box near the UG tank to probes of required length, interconnection wiring between level controller and the concerned contactor in the starter panel as required. The level controller will perform the following functions.

To switch on the pumps (including tube well pumps 1 nos., raw water pumps (Domestic Water Treatment, Domestic & Flushing and etc.) when the level of water in the supply waterline is low and to cut off the pump when the level in the receiving water line is high and switch off the pumps when the level of water in the supply water line is low.

To indicate 2 levels of water in all tanks through a control panel with LEDs

To start the pumps in a cyclic order.

The system shall be complete to ensure automatic quotation of pump in accordance to water level in respective tanks.

The Contractor will include all the under ground and over head tanks and all the pumps as required for level control in this item

Providing and fixing M.S. puddle flanges fabricated out of 6 mm thick M.S. plate of size 200 x 200mm plus dia of pipe of 600 mm long pipe pieces to R.C.C. water tanks / R.C.C. walls. The entire fitting shall be painted with black Japan paint .

25 mm dia

40 mm dia

50 mm dia

65 mm dia

80 mm dia

100 mm dia

150 mm dia

250 mm dia

Providing and fixing on wall face unplasticised - Rigid PVC rain water pipes confirming to IS : 13592 Type A including jointing with seal ring confirming to IS : 5382 leaving 10mm gap for thermal expansion. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of engineer in charge.

150mm dia

200mm dia

Supplying and fixing 150 mm dia PVC End Cap (Clean Outlet Plug) fittings of approved make all complete as per specification and direction of E/l.

DOMESTIC WATER SUPPLY PUMP PANEL (AT PLANT ROOM) Ics=35 KASupplying, Installation, Testing and Commissioning of dust and vermin proof wall / floor mounting type factory built sheet steel enclosed cubical panel, fabricated out of 2.0mm thick CRCA sheet, hinged doors of 2mm thick CRCA sheet, duly painted complete with Aluminium bus bars, inter-connection with solid copper conductor wires / aluminium strips, neutral links, earth bus etc. necessary metering protections & indications and mounted with the following as per specifications and as required (all the starters should have BMS compatible with required NO/NC contacts etc).

INCOMING

125 A, TPN, 35 kA rating MCB - 01 No.

Digital flush type class - I accuracy multifunction meter 0-250A, showing V, A, KWH, KVA, PF etc. with 3 Nos. current transformers of 250/5 Amp ratio, 15 VA Class 1.0 metering.

Coloured LED (Red, Yellow, Blue) phase indicating lamps

Bus Bar

150 Amp. 35 kA, TPN Cu. Bus Bar

OUTGOING

32A, TP,10 kA 'C' series MCCB, coloured LED type ON indication - (1w+1s) Nos & 1 Spare

32A, TP, 10 kA 'C' series MCCB, coloured LED type ON indication -(1w+1s) 1 Nos & 1 Spare

25A, TP, 10 kA 'C' series MCCB, coloured LED type ON indication -(1w+1s) 1 Nos & 1 Spare

16A, TP, 10 kA 'C' series MCCB, coloured LED type ON indication -(1w+1s) 1 Nos & 1 Spare

16A, TP, 10 kA 'C' series MCCB, coloured LED type ON indication -(1w+1s) 2 Nos & 2 Spare

16A, TP, 10 kA 'C' series MCCB, coloured LED type ON indication -(1w+1s) 1 Nos & 1 Spare

Fully automatic DOL starter suitable for 7.0 HP motor including 25 A TP MCCB 'C' series, CT's, Ammeter, Push Button, Indicators, Auto/Manual/OFF switch, SPPR, Relay, metering & indication etc. - (1w+1s) 1 Nos (Borewell Pump)

Fully automatic DOL starter suitable for 3.5 HP motor including 40 A TP MCCB 'C' series, CT's, Ammeter, Push Button, Indicators, Auto/Manual/OFF switch, SPPR, Relay, metering & indication etc. - (1w+1s) 1 Nos.(Domestic Pump at terrace)

Fully automatic DOL starter suitable for 3.0 HP motor including 40 A TP MCCB 'C' series, CT's, Ammeter, Push Button, Indicators, Auto/Manual/OFF switch, SPPR, Relay, metering & indication etc. - (1w+1s) 1 Nos.(Flushing Pump at terrace)

Fully automatic DOL starter suitable for 3.5 HP motor including 25 A TP MCCB 'C' series, CT's, Ammeter, Push Button, Indicators, Auto/Manual/OFF switch, SPPR, Relay, metering & indication etc. - (1w+1s) 1 Nos.(Domestic water transfer pump)

Fully automatic DOL starter suitable for 1.0 HP motor including 25 A TP MCCB 'C' series, CT's, Ammeter, Push Button, Indicators, Auto/Manual/OFF switch, SPPR, Relay, metering & indication etc. - (1w+1s) 2 Nos.(Sump Pump)

Fully automatic DOL starter suitable for 1.5 HP motor including 25 A TP MCCB 'C' series, CT's, Ammeter, Push Button, Indicators, Auto/Manual/OFF switch, SPPR, Relay, metering & indication etc. - (1w+1s) 1 Nos.(Filter feed Pump)

Domestic water supply Panel. (At Plant Room)

Supply and laying ,testing and commissioning of following sizes of Copper conductor control cables with PVC conduit & fixing clamps and effecting proper connections to equipment etc. of following sizes :

4.0Cx6 Sqm

4.0Cx10 Sqm

4C x 16 Sq. mm

Providing and fixing forged brass auto air vent valve PN10 (10.00 Kg/cm2) rating including all fitting with ball valve & accessories. 15 mm dia

Providing, fixing, testing & commissioning of wafer type cast iron butterfly valves conforming to BS 5155 & IS 13095 tested to 15 Kg/Sq.cm pressure for maximum working pressure of 10 bar (PN 10) including all fitting and accessories (Drain, water meter for OH Tank/Riser).

50 mm dia

65 mm dia

80 mm dia

100 mm dia

Constructing water tight brick masonry grease trap with first class bricks in cement mortar 1:6 (1 cement :6 coarse sand), R.C.C. top slab with 1:2:4 mix (1 cement :2 coarse sand :4 graded stone aggregate 20 mm nominal size, foundation concrete 150 mm thick 1:4:8 (1 cement :4 coarse sand :8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement :3 coarse sand) finished with a floating coat of neat cement & M.S. foot rests including fixing in 20 x 20 x 10 cm cement concrete blocks 1:3:6 (1 cement :3 coarse sand :6 graded stone aggregate 20 mm nominal size), two brick masonry baffle walls each of 500 mm depth deep each of 115 mm thickness, 2 Nos C.I. double seal medium duty covers each of 450 x 450 mm size including excavation, backfilling & disposal of surplus earth with a lead upto 50m complete as per standard design. (Note: Cost shall include dewatering & water proofing of Grease trap as directed at site). Grease Trap (Size 1200 x 900 x 1000 mm overall depth).

Providing and fixing G.I. Vent Pipe class 'B' (medium duty) for R.C.C water storage tanks comprising of 600 mm long vertical pipe, return bend with mosquito grating & cast brass perforated coupling including all associated civil work. 100 mm dia

Providing and fixing of mosquito overflow grating /Jali of the following diameters including all fitings & accessories :- 100 mm dia

Supplying, assembly, erection, testing and commissioning of magnetic level sensors and controllers, CPVC probe tube, PP actuating float and all other equipment required for the performance of the system to the satisfaction of the engineer in charge complete including providing and fixing wiring from control junction box near the UG tank to probes of required length, interconnection wiring between level controller and the concerned contactor in the starter panel as required. The level controller will perform the following functions.

To switch on the pumps (including tube well pumps 1 nos., raw water pumps (Domestic Water Treatment, Domestic & Flushing and etc.) when the level of water in the supply waterline is low and to cut off the pump when the level in the receiving water line is high and switch off the pumps when the level of water in the supply water line is low.

To indicate 2 levels of water in all tanks through a control panel with LEDs

To start the pumps in a cyclic order.

The system shall be complete to ensure automatic quotation of pump in accordance to water level in respective tanks.

The Contractor will include all the under ground and over head tanks and all the pumps as required for level control in this item

Providing and fixing M.S. puddle flanges fabricated out of 6 mm thick M.S. plate of size 200 x 200mm plus dia of pipe of 600 mm long pipe pieces to R.C.C. water tanks / R.C.C. walls. The entire fitting shall be painted with black Japan paint .

25 mm dia

40 mm dia

50 mm dia

65 mm dia

80 mm dia

100 mm dia

150 mm dia

Providing and fixing on wall face unplasticised - Rigid PVC rain water pipes confirming to IS : 13592 Type A including jointing with seal ring confirming to IS : 5382 leaving 10mm gap for thermal expansion. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of engineer in charge.

150mm dia

200mm dia

Supplying and fixing 150 mm dia PVC End Cap (Clean Outlet Plug) fittings of approved make all complete as per specification and direction of E/l.

Supply and laying ,testing and commissioning of following sizes of Copper conductor control cables with PVC conduit & fixing clamps and effecting proper connections to equipment etc. of following sizes :

4.0Cx6 Sqm

4.0Cx10 Sqm

4C x 16 Sq. mm

Providing and fixing forged brass auto air vent valve PN10 (10.00 Kg/cm2) rating including all fitting with ball valve & accessories. 15 mm dia

Providing, fixing, testing & commissioning of wafer type cast iron butterfly valves conforming to BS 5155 & IS 13095 tested to 15 Kg/Sq.cm pressure for maximum working pressure of 10 bar (PN 10) including all fitting and accessories (Drain, water meter for OH Tank/Riser).

50 mm dia

65 mm dia

80 mm dia

Providing and fixing G.I. Vent Pipe class 'B' (medium duty) for R.C.C water storage tanks comprising of 600 mm long vertical pipe, return bend with mosquito grating & cast brass perforated coupling including all associated civil work. 100 mm dia

Providing and fixing of mosquito overflow grating /Jali of the following diameters including all fitings & accessories :- 100 mm dia

WATER SUPPLY

Excavating trenches of required width for pipes including excavation for sockets also including for cement concrete craddles, and dressing of sides, ramming of bottoms, depth up to 1.5m including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth including consolidating each deposited layer with minimum 95% by ramming, watering etc. and disposing off surplus excavated soil as directed, within a lead of 50 m. UPTO 1.5M Pipes, cables etc, not exceeding 80 mm dia.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes having thermal stability for hot & cold water supply including all (CPVC) plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of engineer in charge. Internal Work - Exposed on Wall

15 mm nominal outer dia pipes.

20 mm nominal outer dia pipes.

25 mm nominal outer dia pipes.

32 mm nominal outer dia pipes.

40 mm nominal outer dia pipes.

50 mm nominal outer dia pipes.

Providing and fixing Chlorinate Polyvinyl Chloride (CPVC) pipes having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This including jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the the same including testing of joints complete as per direction of engineer in charge.

Concealed work including cutting chases and making good the walls etc.

15 mm nominal outer dia pipes.

20 mm nominal outer dia pipes.

25 mm nominal outer dia pipes.

32 mm nominal outer dia pipes.

Fixing water meter and stop cock in G.I pipe line including cutting and threading the pipe and making long screws etc. complete (cost of water meter and stop cock to be paid separately).

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. [Location : From Bore Well/Tanker water supply line/Municipal line to Underground Water Storage Tank]. 80 mm dia

Constructing masonry Chamber 90x90x100 cm inside, in brick work in cement mortar 1:4 (1 cement :4 coarse sand) for sluice valve, with C.I. surface box 100mm. top diameter, 160 mm bottom diameter and 180 mm deep ( inside) with chained lid and RCC top slab 1:2:4 mix (1 Cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size),i/c necessary excavation foundation concrete 1:5:10 (1 Cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 Cement : 3 coarse sand) 12 mm thick finished with a floating coat of neat cement complete as per standard design:

a) With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

(i) Domestic tank

(i)Flushing tank

(i) Fire tank

Providing and fixing C.P brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 grams with threaded end for hose connection.

Providing and fixing gun metal non- return valve of approved quality (screwed end).

50 mm dia nominal bore-vertical

65 mm dia nominal bore-vertical

80 mm dia nominal bore-vertical

Supplying and fixing C.I. cover without frame for manholes:

500 mm diameter C.I. cover (medium duty) the weight of the cover to be not less than 58 kg.

Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete :

50 to 80 mm nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :

25 mm nominal bore

20 mm nominal bore

32 mm nominal bore.

40 mm nominal bore

50 mm nominal bore

65 mm nominal bore

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete

15 mm nominal bore

20 mm nominal bore

25 mm nominal bore

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) :

20 mm nominal bore

25 mm nominal bore

32 mm nominal bore.

40 mm nominal bore

50 mm nominal bore

65 mm nominal bore

RAIN WATER HARVEST

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-incharge.All kinds of soil

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer-in-charge, upto 90 metre depth below ground level.All types of soil

300 mm dia

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge.

200 mm nominal size dia

Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge.

200 mm nominal size dia

Supplying, filling, spreading & leveling stone boulders of size range 5 cm to 20 cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge

Supplying, filling, spreading & leveling gravels of size range 5 mm to 10 mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.

Supplying, filling, spreading & leveling coarse sand of size range 1.5 mm to 2 mm in recharge pit, in required thickness over gravel layer, for all leads & lifts, all complete as per direction of Engineer -incharge.

Gravel packing in tubewell construction in accordance with IS: 4097, including providing gravel fine/ medium/ coarse, in required grading & sizes as per actual requirement, all complete as per direction of Engineer-in-charge.

Providing and fixing factory made precast RCC perforated drain covers, having concrete of strength not less than M-25, of size 1000 x 450x50 mm, reinforced with 8 mm dia four nos longitudinal & 9 nos cross sectional T.M.T. hoop bars, including providing 50 mm dia perforations @ 100 to 125 mm c/c, including providing edge binding with M.S. flats of size 50 mm x 1.6 mm complete, all as per direction of Engineerin-charge.

Development of tube well in accordance with IS : 2800 (part I) and IS: 11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully developed, measuring yield of well by "V" notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, i/c disinfection of tubewell, all complete, including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge.

Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of:

200 mm dia

Providing and fixing M.S. clamp of required dia to the top of casing/housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete.

200 mm dia

Providing and fixing Bail plug/ Bottom plug of required dia to the bottom of pipe assembly of tubewell as per IS:2800 (part I).

200 mm dia

(WET RISER SYSTEM - PUMPING EQUIPMENTS)

Supply, Installation, Testing and Commissioning of Electric Driven Main Fire Pump suitable for auto operation & consisting of following: complete in all respect as required.The pump shall also be capable of discharging not less than 150 % of the rated discharge at a head of not less than 65% of the rated head. The shut off head shall not exceed 120% of the rated head. (Sprinkler & Hydrant Pump)

a) Horizontal end suction type, centrifugal, single stage, pump of cast iron body and bronze impeller with stainless steel shaft, mechanical seal to ensure a minimum pressure of 3.5 kg/sq. cm. at highest and farthest outlet at specified flow of 2280 lpm at 88 Mtr. head confirming to IS 1520.

b) Suitable HP squirrel cage induction motor, TEFC synchronous speed 2900 RPM (with permissible slip), suitable for operation on 415 volts, 3 phase 50 Hz. AC with IP 55 protection for enclosure, horizontal foot mounted type with Class- 'F' insulation, confirming to IS-325.

c) Common base frame fabricated out of M.S channel of suitable size, flexible coupling, coupling guard, foundation bolts and pressure gauge , pressure switch with valve etc. Suitable cement concrete foundation duly plastered, with anti vibration pads etc. complete as per manufacturer's design & standards and as per detailed specifications.

Supplying, installation, testing and commissioning of electric driven terrace pump suitable for automatic operation and consisting of following, complete in all respects, as required: (Terrace Pump)

Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical confirming to IS : 1520

Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase, 50 Hz, AC supply with IP55 class of protection for enclosure,horiziontal foot mounted type with Class-'F' insulation,conforming to IS-325.

M.S.fabricated common base plate, coupling, couplingguard, foundation bolts etc.as required.

Suitable cement concrete foundation duly plasteredand with anti vibration pads.

900 lpm at 35 m Head

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

Supply, Installation, Testing and Commissioning of Diesel Engine Driven Main Fire Pump suitable for auto operation and consisting of following: complete in all respect as required. The pump shall also be capable of discharging not less than 150 % of the rated discharge at a head of not less than 65% with the rated head. The shut off head shall not exceed 120% of the rated head.

a) Horizontal end suction type, centrifugal, single stage, pump of cast iron body and bronze impeller with stainless steel shaft, mechanical seal to ensure a minimum pressure of 3.5 kg/sq. cm. at highest and farthest outlet at specified flow of 2280 lpm at 88 Mtr. head confirming to IS 1520.

b) Suitable HP 1500 RPM, 4 stroke, cold starting type Diesel Engine with Heat Exchanger confirming to relevant BIS & IS Standards, complete with all required accessories / system, fuel oil filter, lubricant oil pump with filter, 2 Nos. starting batteries of 180 AH capacity each with suitable angle iron stand, engine starting panel having all the controls meters, gauges, tachometer, hour meters, starting switch with keys for manual starting, auto starting mechanism, Including inbuilt electrical panel which will be activate by pressure switch, Including cables etc., 24 Volts electric starting equipment, Diesel Tank for 8 hrs continuous running of diesel engine, having minimum capacity of 200 Ltrs. (tank made out of 3mm thick M.S. Sheet with filling Cap, drain Cock, diesel indicator duly mounted on M.S. angle) exhaust pipe extended upto 1 mtr. outside pump house, duly insulated with 50 mm. thick glass wool with 1.0 mm. thick aluminium sheet cladding, exhaust residential silencer, stop solenoid for auto stop in the event of fault with audio indications, painted with post office red colour etc. as required.

c) M.S. fabricated Common base frame, flexible coupling, coupling guard, foundation bolts and pressure gauge , pressure switch with valve etc. Suitable cement concrete foundation (minimum 6" above from ground floor) duly plastered, with anti vibration pads etc. complete as per manufacturer's design & standards and as per detailed specifications.

Supplying, Installation, Testing and Commissioning of Electric Driven Pressurization Pump (Jockey Pump) suitable for auto operation and consisting of following: complete in all respects as required. The pump shall also be capable of discharging not less than 150 % of the rated discharge at a head of not less than 65% with the rated head.

a) Horizontal type, centrifugal end suction type pump of cast iron body and bronze impeller with stainless steel shaft, mechanical seal, gland packing and flow of 180 Ipm at 88Mtr. head confirming to IS:1520.

b) Suitable HP (Minimum 4.0-5.0 HP) squirrel cage induction motor TEFC type 2900 RPM suitable for operation on 415 volts, 3 phase 50 Hz. AC with IP-55 class of protection for enclosure, horizontal foot mounted type with Class - 'F' insulation, confirming to IS:325.

c) Common base frame fabricated out of M.S channel of suitable size, flexible coupling, coupling guard, foundation bolts and pressure gauge , pressure switch with valve etc. Suitable cement concrete foundation duly plastered, with anti vibration pads etc. complete as per manufacturer's design & standards and as per detailed specifications.

Supplying and fixing air vessel made of 250 mm dia, 8 mm thick MS sheet, 1200 mm in height with air release valve on top and flanged connection to riser, drain arrangement with 25 mm dia gun metal wheel valve with required accessories, pressure gauge and paintingwith synthetic enamel paint of approved shade as required.

Fabricating, Supplying, Installation, Testing and Commissioning Air Vessel of continuous welded construction with flanged discharge header on the top of each riser fabricated out of 8 mm thick MS sheet, Air Release Valve complete with suitable drain arrangement with 25 mm dia gun metal ball valve complete with all accessories etc. pressure gauge, synthetic enamel paint of approved shade as required of the following sizes

2 Meter high and 450 mm dia suitable to operate Jockey Pump, Main Fire Pump , Sprinkler pump & Diesel Engine Driven Fire Pump

Supplying and fixing Single Headed Internal Hydrant Valve oblique pattern with instantaneous Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked, conforming to IS : 5290 (Type A), with 80 mm dia flanged inlet, with ABS cap and chain complete with all accessories etc. as required.

Supply, Installation, Testing and Commissioning of 63 mm dia. 15 Mtr. Long RRL hose pipe with 63 mm dia. male and female stainless steel couplings duly binded with GI wire rivets etc. ISI marked, IS 636 (type-A) as required.

Supplying and fixing 63 mm dia. Stainless Steel branch pipe with 20mm dia nozzle conforming to IS:903. suitable for instantaneous connections to hose pipe coupling etc. as required.

Supplying and Fixing First Aid Hose Reel, wall mounting swinging type complete with drum & bracket of MS construction, spray painted in Post office Red, confirming to IS 884/1995 with upto date amendments, complete with the following as required.

30 Meter long 20 mm dia water hose Thermoplastic (Textile reinforced) Type - 2 as per IS : 12585

20 mm dia. ball valve & nozzle.

Drum and brackets for fixing the equipments on wall.

Connection from riser with 25 mm dia (Gun metal) stop valve & M.S. Pipe.

Supplying, installation, testing and commissioning of weather proof M.S cabinet size 1200 mm x 2100 mm x 600mm deep fabricated from 1.6mm thick M.S. sheets and M.S angle 40mmx40mmx6mm complete with glass, locking arrangements to accommodate the following.

Gunmetal single headed Hydrant valve - 1 No.

Fire Hoses 63mm, 15 M long with accessories - 2 Nos.

Short branch - 1 No.

First Aid hose Reel - 1 No.

Fire Extinguisher - 2 Nos.

Fireman's Axe - 1 No.

Pressure Gauge - 1 No.

The cabinet shall be painted with one coat of primer and 2 coats of synthetic enamel paint of approved shade.

Supplying and fixing of fire brigade connection of cast iron body with gun metal male & female instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required :

2 way - 100 mm dia M.S. Pipe

4 way - 150 mm dia M.S. Pipe

(PIPING, VALVES AND ACCESSORIES)

Supplying, laying, fixing, testing and commissioning of following sizes (NB) of class 'C' M.S. pipes confirming to IS 1239 and 3589 including cutting, threading, welding etc. and providing all fittings e.g. elbows, reducers, clamps, hangers, flanges, gaskets, nuts, bolts and washers etc. including painting of pipes and fittings with red paint over a coat of ready mixed primer, both of approved quality and shade including cutting holes and chases in brick or RCC walls/slabs and making good the same etc. complete in all respect as required. (The Welding shall not be done for piping less than 50 mm dia.)

150 mm dia

100 mm dia

80 mm dia

65 mm dia

50 mm dia

40 mm dia

32 mm dia

25 mm dia

Supplying, Installation, Testing and Commissioning of Butterfly valves of PN 1.6 rating of following sizes with EPDM rubber lining seat and CF-8 stainless steel disc duly ISI marked and stainless steel stem with lever/gear operation and cast iron body in powder coated finish for fire fighting application complete in all respects confirming to IS: 13095 as required.

150 mm dia

80 mm dia

65 mm dia

Supplying and fixing Orifice Plate made of 6 mm thick, stainless steel with orifice of required size in between flange & landing valve of external and internal hydrant to reduce pressure to working pressure of 3.5 Kg / cm2 complete as per specifications as required.

Providing, Installation, Testing and Commissioning of double flanged cast iron Dual Plat Check Valve (Non-Return Valve), PN 1.6 of following sizes confirming to IS : 5312 complete with EPDM rubber lining seat and stainless steel disc, rubber gasket, Gl bolts, nuts, washers etc. as required.

150 mm dia

65 mm dia

Supplying, Installation, Testing and Commissioning of CI body flanged (both ends) type serviceable suction / Y strainer with (stainless steel / brass mesh) conforming to relevant IS specifications amended upto date complete including providing and fixing nuts, bolts, washers, gaskets etc. complete as required.

150 mm dia

65 mm dia

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

Providing & fixing double flanged Metallic expansion with M.S. fixed flanges (PN-1.6) joint (suitable for system test pressure) of standard length as per manufacturers specs including rubber gaskets, flanges, nuts, bolts and washers complete as required as per specifications.

150 mm dia

65 mm dia

Providing, fixing, testing and commissioning of 15mm dia quartzoid bulb type sprinklers of rating 68 degree centrigade with required accessories :

Pendent Sprinkler

Upright Sprinkler

Sidewall Sprinkler

Providing & fixing of pressure gauge in M.S. pipe line including connection etc. as required.

Providing & fixing flow switch in following sizes M.S. pipe including connection etc as required.150mm dia

Providing, fixing, testing & commissioning of installation control valve of cast irom body, brass/bronze working parts comprising of water motor alarm, bronze seat clapper, clapper arm and hydraulic driven mechanical gong bell to sound continous alarm when the wet riser/sprinkler system activates, pressure gauges, emergency release, strainer, pressure switch, cock valve complete with drain valve and bypass, test control box, ball valves, MS pipe of required size, flanges, orifice pate, gasket etc of following sizes as required

150mm dia

Supplying, installation, testing & commissioning of sprinkler flexible pipe (UL Listed) of stainless steel complete with 15 NPT on reducer thread with maximum working pressure of 175 PSI test pressure of 875 PSI (Burst) with branch line (Inlet) 25mm NPT male thread to sprinkler head (Outlet) 15mm NPT female thread with reducer, nipple, 2 side brackets, center bracket, stockbar of following sizes coplete as required.

Supplying and fixing of Fire Man's axe with heavy insulated rubber as per standard conforming to IS 926.

(FIRE EXTINGUISHERS)

Powder Fire Extinguisher (Stored Pressure type) Capacity 09 Kg duly ISI marked conforming to IS: 15683:2006, with IS 14609, ISI marked ABC powder complete with squeeze grip release valve, discharge pipe locking arrangement, pressure gauge, operation manual and bracket. Operating Temperature: - 10ºC to + 55ºC. Brand LIFEGUARD

Providing and fixing fire extinguisher of carbon dioxide type consisting of brand new high pressure steel cylinder bearing IS: 7285 mark and having the approval of controller of explosives Nagpur, wheel type valve bearing IS:3224 mark internal discharge tube, 1 meter long high pressure discharge hose, non conducting horn, suspension bracket, fully charged bearing IS: making fixed to wall as directed conforming IS : 15683:2006

4.5kg capacity cylinder

Providing and fixing in position approved make fire bucket of 24 gauge, galvanized steel, standard 9 liters capacity and of round bottom shape, panted white inside and red outside and black on bottom dome with letters ‘FIRE’ in black and gold with all mounting bracket and screws.

Providing and fixing of fire Bucket Stand including sheet metal (16 gauge) shade for 2 buckets. Platform and associated civil works complete.

(MOTOR CONTROL PANELS)

Supplying, assembling, erecting, connecting, testing and commissioning of Outdoor type fire fighting double door lockable type with epoxy paint. This panel shall be mounting on MS/brick pedestal support upto 400 mm high from ground level,cubical, dust, vermin proof and outdoor type (IP65) fabricated as per specification laid in document with following incomming and outgoing feeders including making connections/inter-connections testing and earthing etc. required with necessary interlocking with existing panel as shown in drawing as per specification and mounted with the followings.

Incoming

1 No. - 630A 4P ATS

1 No. - 630A TPN MCCB of fault breaking capacity 50 kA (Ics = Icu upto 500V), fitted with interlocked door, automatic safety shutters, mechanical ON/OFF and service/test/isolated position indicators and frame earthing contact, conforming to IS-13947-2 1993 as amended up-to-date complete with following accessories for each MCCB.

Independent electrical/manual spring closing mechanism - 1 No.

Microprocessor releases based relay(EMI & EMC certified) for over current, earth fault & short circuit protections with trip indications for each - 1 set.

Dual core calibrated digital Multifunctional meter of class 1.0 to record demand (KVA), energy (KWH & KVAH), power factor, current (in each phase and the neutral), voltage (between phases and between each phase and neutral) and 3 Nos. dual core CT of A Class 1.0 accuracy and 15 VA burden.

Following indicating lamps and push buttons for each MCCB with back up 2A SP MCB .

3 No. Phase indicating Lamps .

Indicating Lamps for the following;

Bus Bar

800 Amp. 50 kA, TPN Al. Bus Bar

Outgoings:

Following rated 420V,50KA MCCB's with overcurrent and short circuit releases Microprocessor based with ON,Trip indications, front operating handle & door interlock along with 2A SP MCB backup protection and control terminals & wiring as required. etc. complete in all respects as mentioned in specifications and as required For each outgoing:

125 Amp. TP MCCB -4 Nos.(4 spare)

16 Amp. TP MCCB -2 Nos.(2 spare)

The Panel shall have necessary arrangement to start the pumps at automatic mode in following sequence. a) The Jockey Pump is start to maintain the drop in pressure in pipe line and also in case of opening of any hydrant to maintain the required pressure. b) The main fire pump will start in case of jockey doesnot able to maintain the required pressure due to opening of any fire hydrant. c) To start the diesel engine operated fire pump in case of failure of power supply or in case of minimum fire pump is not able to required pressure.

(d) Diesel Engine Control

(ii) Indication lamp for High Water Temp. and Engine on indication and suitable tripping devices, overload, earth fault protection relays etc as required.

(iv) All standard relays and accessories for automatic operation of diesel engine.

(e) System Controller

Designing, Supply, Installation, Testing and commissioning of system controller to control operation of Main Fire Pump, Pressurization Pump in sequence as per specification consisting of relays, timers, sensor, annunciation window for fault indication, complete as per specification.

Fire panel as above

METERING INDOOR UNIT

Installation of indoor metering unit (without CT, PT) as per the approved make of State electricity board

Providing & fixing 11KV CT & PT in above metering indoor unit and getting them calibrated from State Electricity Boards before fixing.

11KV SINGLE VCB PANEL BOARD (NEAR METER)

Design, manufacturer, supply of panel board fabricated out of minimum 2 mm thick sheet steel as per specifications. The panel shall be complete with cable termination arrangement suitable for incoming and outgoing each 1 run x 3C x 240 Sqmm XLPE 11 KV cable and copper bus bar arrangement. The panel shall comprise of the following:

Single Panel Board

Incomer:-

1No. 11kV 630A 25kA drawout type VCB with motorised spring charge mechanism for 240V AC, closing & tripping coils suitable for 24V DC

Each incomer comprising with following accessaries.

1 No. Mechanical ON/OFF Indicator

1 No. Aux Switch 6NO + 6NC

Panel, Busbar, CT, PT

1 No. Fully compartmentalised sheet steel enclosure floor mounting type with automatic safety shutters, independent pressure discharge flaps, PVC sleeved busbar, etc with provision for terminating PVC/PILC/XLPE Cable

3 Nos. Resin Cast CTs 100/50/1-1A with Core 1 : 7.5VA CL 1 Core 2 : 7.5VA CL 5P10

3 Nos. PT - 11kV/√3//110/√3V ,CL 1.0, 50VA

Breaker Panel indication Lamps :

6 Nos. ON/OFF/TRIP/TRIP Ckt Healthy/Spring Charged

Switches and other Accessories

8 nos.Fuses

1 No. Heater

1 No. Thermostat

1 No. 6 Window Annunciator

1 No. Plug & Socket

1 No. Test Terminal Block

1 No. T-N-C Switch

1 No. Emergency Push Button

1 No. Hooter

Meters

1 No. Analog Ammeter + ASS

1 No. Analog Voltmeter + VSS

1 No. Digital Multifunction Meter - Quasar

Relays

1 No. MC 61A (O/C + E/F - IDMT+Inst)

1 No. AVAJH13 Master trip relay (Ashida)

1 No. TCS Relay

Three VCB Panel Board

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

11KV PANEL BOARD NEAR TRANSFORMER

Design, manufacturer, supply of panel board fabricated out of minimum 2 mm thick sheet steel as per specifications. The panel shall be complete with cable termination arrangement suitable for incoming and outgoing each 1 run x 3C x 240 Sqmm XLPE 11 KV cable and copper bus bar arrangement. The panel shall comprise of the following:

Single Panel Board

Incomer:-

1No. 11kV 630A 25kA drawout type VCB with motorised spring charge mechanism for 240V AC, closing & tripping coils suitable for 24V DC

Each incomer comprising with following accessaries.

1 No. Mechanical ON/OFF Indicator

1 No. Aux Switch 6NO + 6NC

Panel, Busbar, CT, PT

1 No. Fully compartmentalised sheet steel enclosure floor mounting type with automatic safety shutters, independent pressure discharge flaps, PVC sleeved busbar, etc with provision for terminating PVC/PILC/XLPE Cable

3 Nos. Resin Cast CTs 100/50/1-1A with Core 1 : 7.5VA CL 1 Core 2 : 7.5VA CL 5P10

3 Nos. PT - 11kV/√3//110/√3V ,CL 1.0, 50VA

Breaker Panel indication Lamps :

6 Nos. ON/OFF/TRIP/TRIP Ckt Healthy/Spring Charged

Switches and other Accessories

8 nos.Fuses

1 No. Heater

1 No. Thermostat

1 No. 6 Window Annunciator

1 No. Plug & Socket

1 No. Test Terminal Block

1 No. T-N-C Switch

1 No. Emergency Push Button

1 No. Hooter

1 No. Power pack

1 No. Surge Arrestor

Meters

1 No. Analog Ammeter + ASS

1 No. Analog Voltmeter + VSS

1 No. Digital Multifunction Meter - Quasar

Relays

1 No. MC 61A (O/C + E/F - IDMT+Inst)

1 No. AVAJH13 Master trip relay (Ashida)

1 No. TCS Relay

Three VCB Panel Board

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

11KV/ 0.433KV 1600KVA OIL TYPE TRANSFORMER

Supplying ,Assembling , erecting, testing and commissioning of 1600 KVA 11KV/0.433KV voltage 3phase 50Hz, outdoor type copper wound, OIL type step down transformer complete with all modern fittings as given in the specifications including , lifting lugs, Roller type bi-directional wheels, suitable boxes on both the ends for cable entry/ bus duct,winding temprature indication & alarm, , earthing terminals,buchholz relay, diagram and rating plat etc. as required.

The transformers shall be installed in hot, humid tropical atmosphere. All equipment accessories and wiring shall be provided with tropical finish to prevent fungus growth

The transformers shall be oil Type & capable of continuous operation of rated output under the operating conditions of voltage and frequency variations as per statutory limits governed by relevant Indian Standard and Indian Electricity Rules, 1956 / IEC with latest amendments in force.

Requirement: 11KV/433V voltage oil type with OFF LOAD Tap Changer, Tapping range +7.5% to -15% in steps of 2.25% (HV side), oil cool ONAN

Voltage Ratio: No load voltage 11000/433volts within tolerance as stipulated in latest IS standard.

Rating: The transformer shall have a continuous rating as specified at any of the specified tapping position and with the maximum temperature rise specified.

Type of Load: The transformer shall be suitable for carrying unbalanced load up to 90% load within temperature rise indicated in the Indian Standard specification ‘Guide for loading of oil Transformer

Overloads: The transformers shall be suitable for carrying overload within temperature rise indicated in IS ‘Guide for Loading of oil Transformer

Connections: H.V. Delta and L.V Star connected with neutral brought out on the secondary side for connection to earth; Vector group DYn11 of IS:2026

Each 11KV/433V Dual voltage Step down transformers shall be provided with the following fittings and accessories: Rating diagram and terminal marking plate for transformer.

Lifting lugs for transformer

Bi-directional Rollers

Rating diagram and terminal marking plate for transformer

Earth terminals (2 Nos) for body earthing for transformers

Inspection door for access to terminal connections for transformers

Suitable cable termination arrangement for M.V. side box with extended Bus bars for cables or Bus duct connection and cable box terminations on H.V. Side, suitable for 3C x 240/300sq. mm 11 K.V. XLPE Aluminum Conductor cable or sutable rating Busduct.

Necessary hardware, clamps, lugs etc. for terminations of H.V. Cables on HV side and cable termination on M.V. Side.

Winding temperature indicator with contacts for remote alarm and tripping.

DG SETS and BATTERY CHARGER

Supply, installation, testing & commissioning of 415 V, 250 kVA stand by rating ( radiator cooled type ) diesel generating set along with base frame, Alternator, Static Excitation System, Lube Oil System, Electronic Governor, Batteries, Battery Charger, Instrumentation, day oil fuel tank including the piping of approx. 12 mtr, Silencer with Bellows, Alarms, Engine Control Panel, AVM Pads, AVR Panel, Terminal Arrangements including bus duct termination box with all associated equipment / work as per specifications. Alternator shall have class-H insulation and rated for 680 KW output at 47deg. C. Engine shall not be derated upto 50 deg.C ambient. (First Fill oil of 990 litre for Day oil tnak to be considered in the offer). Supply and installation of suitabkle dia SS flexible bellows with matching flanges along with required hardware i.e. gasket, nut bolt, washer etc as required.

Supply, laying of following sizes of MS Piping for Exhaust including providing suitable bends, reducers & supporting arrangement at suitable intervals including insulation on entire length of exhaust pipe with 50mm thick Rockwool insulation & painting etc. as required.

250 mm dia

EXTERNAL ELECTRICAL WORKS

Constructing masonry Chamber 60x60x75 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100 mm top diameter, 160 mm bottom diameter and 180 mm deep (inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ), i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design :

Constructing masonry Chamber 90x90x100 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100 mm top diameter, 160 mm bottom diameter and 180 mm deep (inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ), i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design :

Constructing masonry Chamber 120x120x100 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100 mm top diameter, 160 mm bottom diameter and 180 mm deep ( inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) , i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coatof neat cement complete as per standard design :icks of classdesignation 7.5

Providing, laying and fixing following dia RCC pipe NP2 class (light duty) in ground complete with RCC collars, jointing with cement mortar 1:2 (1 cement : 2 fine sand) including trenching (75 cm deep) and refilling etc as required.

100 mm dia

150 mm dia

Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc..direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete as required

63 mm dia (OD-63 mm & ID-51 mm nominal)

120 mm dia (OD-120 mm & ID-103 mm nominal)

160 mm dia (OD-160 mm & ID-135 mm nominal)

Supply of 7.0 Mtr High Octagonal pole ( Hot Dip Galvanized) BOP-7030 with top dia 70mm and bottom dia 130mm and made of 2mm thick base plate of size 200mmX200mmX12mm ( LXBXT) and with suitable size of foundation bolts and complete as required

Erection of metallic pole of following length in cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) foundation including excavation and refilling etc. as required.

Above 6.5 metre and upto 8 metre

Supply, installation, testing and commissioning of 35W Kwp power rating high efficiency eco friendly with compact ascesthic design Integrated all-in-one solar street light with system efficacy ≥ 170 lm/watt CRI>70 IP-65 complete with all accessories sush as lithium ferro phosphate battery, Mono crystalline solar panel and MPPT charger and built into sensor based luminaire made of Pressure die cast aluminium and suitable bracket for top pole mounting etc complete as required.

Supply of 12.0 Mtr High Mast in one section construction S355 grade as per BS-EN-10025 Top dia 100mm, bottom dia 360mm, plate thickness 3mm, 12side polygon, galvanosation as per BS EN ISO 1461, base plate dia 520mm, base plate thickness 25mm, GI single spike lighting protection, maximum wind speed 47m/s as per IS :875 (part-III) with 6 nos. foundation bolt of PCD 445mm TS 600/24mm dia/850mm long luminaries carriage: material of 40NB ERW class B mM.S pipe dia of carriage ring 450mm (ID) with 8 arm, welded 2 section having carrying capacity upto 8 luminaries trailing cable 5core 2.5sq.mm PVC flexible copper conductor winch/power tool double drum SWL 350kg with 0.75HP 6pole single speed integral motor rope grade AISI:304, 7/19 construction dia 5mm BLC 1450x2 having 2nos. of continues rope. Aviation obstruction light twin dome aviation obstruction light LED type required. feeder pillar control panel housing 32a TPN MCB incoer single dial timer 25A contactor circuit for the automatic control of luminaries outgoing terminals and control circuit for power tool & Remote control.

For 120MT High mast : ITC of high mast light fixture with the help of suitable tools and plants wiring of luminaries with material like insulared PVC sheathed flexible cable of suitable copper conductor lugs MCB and all labour & construction of shallow foundation with M25 grade concrete for the high mast considering safe soil beaninh capacity of 10T/MT high mast.

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

Supply of following sizes sizes of PVC insulated PVC sheathed aluminium conductor armoured 1.1 KV grade as as required.

2C x 6 sq mm

2C x 10 sq mm

2C x 16 sq mm

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required.

Upto 35 sq. mm

Laying of one number additional PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size cables in the existing RCC/ HUME/ Stoneware/ Metal pipe as required

Upto 35 sq. mm

Supplying and making end termination of following sizes with brass compression gland including providing and crimping solderless plugs/ferrules of sizes PVC insulated PVC sheathed aluminum conductor armoured cable 1.1 KV grade.

2C x 6 sq mm

2C x 10 sq mm

2C x 16 sq mm

Supplying and fixing of outdoor type junction box( IP 67 ) suitable to incoming and outgoing up to 16 sq. mm Al Armoured Cable. The juction box shall also be suitable for 3 Nos. outgoing circuits each consisitng of 3 Nos. 2.5 sq mm copper wired wires

Supplying and laying 6 SWG G.I. wire at 0.50 metre below ground level for conductor earth electrode, including solding etc. as required.

Wiring with 2 x 2.5 sq.mm FR PVC insulated copper conductor single core cable in surface / recessed PVC conduit alongwith 1 No. 2.5 sq.mm FR PVC insulated copper conductor single core cable for loop earthing as required

LT CABLES

Supplying of following 1100 volt grade XLPE insulated PVC sheathed aluminium / Copper conductor armoured cables as per specification as required. PVC/ XLPE insulated PVC sheathed heavy duty, armoured electrical cables with Aluminium conductor for working voltage upto and including 1100volts ( conforms to IS:1554, Part-1)

3.5 core 300sq. mm.

3.5core 240sq. mm.

3.5 core 185sq. mm.

3.5core 150sq. mm.

3.5core 120sq. mm.

3.5 core 95sq. mm.

3.5 core 70sq. mm.

3.5 core 50sq. mm.

3.5 core 35sq. mm.

3.5 core 25sq. mm.

4 core 16sq. mm.

4 core 10 sq. mm.

4 core 6 sq. mm.

PVC/ XLPE insulated PVC sheathed heavy duty, armoured electrical cables with Copper conductor for working voltage upto and including 1100volts ( conforms to IS:1554, Part-1)

4 core 1.5 sq. mm. ( Copper Control cable)

7 core 1.5 sq. mm. ( Copper Control cable)

12 core 1.5 sq. mm. ( Copper Control cable)

Layrng and fxing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required.

Upto 35 sq. mm

Above 35 sq. mm and upto 95 sq. mm

Above 95 sq. mm and upto 185 sq. mm

Above 185 sq. mm and upto 400 sq. mm

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required.

Above 35 sq. mm and upto 95 sq. mm

Above 95 sq. mm and upto 185 sq. mm

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

Providing and fixing 6 SWG dia. GI wire on surface or in recess for loop earthing along with the existing surface / recessed conduits / submain wiring / cable as required.

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc, as required

Laying of one number additional PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground in same trench in one tier horizontal formation including excavation, sand cushioning, protective covering and refilling the trench etc as required.

Upto 35 sq. mm

Above 35 sq. mm and upto 95 sq. mm

Above 95 sq. mm and upto 185 sq. mm

Above 185 sq. mm and upto 400 sq. mm

Laying of one number additional PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size cables in the existing RCC/ HUME/ Stoneware/ Metal pipe as required

Upto 35 sq. mm

Above 35 sq. mm and upto 95 sq. mm

Above 95 sq. mm and upto 185 sq. mm

Above 185 sq. mm and upto 400 sq. mm

Supplying and making end termination of following sizes with brass compression gland including providing and crimping solderless plugs/ferrules of sizes PVC insulated PVC sheathed aluminum conductor armoured cable 1.1 KV grade.

3.1/2 core 300sq. mm.

3.1/2 core 240sq. mm.

3.1/2 core 185sq. mm.

3.1/2 core 150sq. mm.

3.1/2 core 120sq. mm.

3.1/2 core 95sq. mm.

3.1/2 core 70sq. mm.

3.1/2 core 50sq. mm.

3.1/2 core 35sq. mm.

4 core 25sq. mm.

4core 16sq. mm.

4 core 10sq. mm.

Supplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc. as required. (Powder coated shall be of Siemens Grey Colour- RAL 7032)

100mm width X 50mm depth X 1.6 mm thickness

150mm width X 50mm depth X 1.6 mm thickness

300mm width X 50mm depth X 1.6 mm thickness

450mm width X 50mm depth X 2.0 mm thickness

600mm width X 62.5mm depth X 2.0 mm thickness

750mm width X 75mm depth X 2.0 mm thickness

900mm width X 75mm depth X 2.0 mm thickness

11KV HT CABLE

Supply of cable XLPE -PVC insulated PVC sheathed galvanised steel strip armoured electric power cable with aluminium conductor 11000 volt grade of size 3CX300 sqmm.

Laying of one number XLPE power cable of 11 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required.

Above 120 sq. mm and upto 400 sq. mm

Laying of one number XLPE power cable of 11 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required.

Above 120 sq. mm and upto 400 sq. mm

Supplying and making indoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required :

Supplying and making outdoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 33 KV grade as required :

415V LT PANELS & DISTRIBUTION BOARDS

MAIN LT PANEL ( 50 kA )

Incoming Air Circuit Breaker from TRF

1 nos. 2500 amps 4 pole electrically operated manually draw out type air circuit breaker each with following accessories :

Digital energy meter (Schneider – EM6400NG or equivalent) of accuracy class-1, with 3 Nos. 2500 amps 15VA CTs.

Phase indicating light shall be protected by suitable rating MCB’s. - 3 Sets

Breaker ON / OFF / TRIP indicating lights with control MCB’s. - 1 Set

24 V DC Shunt trip coil. - 1 Set

240 V under voltage release. - 1 Set

Breaker control switch - 1 Set

IDMT relay- 1 Set

Under Volate & Over Voltage relay

Master trip relay- 1 Set

Auxiliary contacts required for necessary interlocking of breakers.

Bus Bars

3200 amps TPN Aluminium bus bars with colour coded heat shrinkable insulating sleeves - 1 Set.

Outgoing

2 Nos. 1000 Amps TPN Pole manually operated fully drawout type air circuit breaker and ON/OFF/Trip & shunt trip coil.

2 Nos. 800 Amps TPN POLE MCCB and ON/OFF/Trip & shunt trip coil.

6 Nos. 500/630 Amps TPN POLE MCCB and ON/OFF/Trip & shunt trip coil.

7 Nos. 400 Amps TPN POLE MCCB and ON/OFF/Trip & shunt trip coil.

5 Nos. 315 Amps TPN POLE MCCB and ON/OFF/Trip & shunt trip coil.

7 Nos. 250 Amps TPN POLE MCCB and ON/OFF/Trip & shunt trip coil.

6 Nos. 200 Amps TPN POLE MCCB and ON/OFF/Trip & shunt trip coil.

7 Nos. 100/125/160 Amps TPN POLE MCCB and ON/OFF/Trip & shunt trip coil.

All breakers shall be electrically interlocked

All ACB’s/MCCB’s shall be suitable for 50 kA breaking capacity.

PLC for load management , interlocking , DG auxiliary and supervision.

2 kVA UPS for 30 MinutesBackup for control wiring.

Touch screen display panel having 10.4 inch - TFT Display - Color screen as per specification.

Auto starting / Auto synchronizing / Auto load balancing and auto load management panel for 2 No. DG Sets

All outgoing feeder shall have digital electronic energy meter ( EM 6438 of conzerv make or equivalent ) with suitable no. of CT,s and RS 485 port .

1 No. --/ 5, 15 VA dual ratio CT’s shall be provided for APFCR on each transformer's incomer.

Wiring and supply, installation of space heater, Humidistatae and control MCB’s shall be provided all vertical sections.

Suitable danger board shall be provided.

All bus bar section / backside panels shall have hinged type door.

9 W fitting with LED lamp, switch shall be provided in each vertical section.

Incomer ACB receiving power from transformer/D.G shall have suitable provision for Cables connection..

All Electronic Energy meter shall be pre wired for BMS connection upto central point within the panel with sheilded cable.

All incoming & outgoing feeders shall have minimum 4 nos. potential free contacts.

1No. 24V DC Supply Power Pack with suitable (bidder shall provide the Ah calculation) Ah Maintenance free Battery back up. Power Pack should be with Protections of over voltage/ under voltage/ over charging.

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

450KVAR CAPACITOR PANEL

INCOMER

Direct From MLP

METERING & INDICATION

1 set of phase indicating lamps

1 No. (0-500V) Voltmeter with Built-in VSS with 3 nos. 2A SP MCB

1 No. 12 steps APFC relay

1 set of Ammeter (0-1200A) with ASS and 3 nos.600/5A, CTs'

BUS-BAR

1 Set of 1500A TPN Aluminium Bus Bar with colour coded PVC Sleeves

OUTGOINGS

4 Nos.of 125A TP MCCB (35 KA) with 140A TP contactor (AC-3 duty)

7 Nos. of 100A TP MCCB (35 KA) with 70A TP contactor (AC-3 duty)

1 No. of 63A TP MCCB (35 KA) with 40A TP contactor (AC-3 duty)

4 Nos. of 32A TP MCCB (35 KA) with 20A TP contactor (AC-3 duty)

3 No.of 16A TP MCCB (35 KA) with 10A TP contactor (AC-3 duty)

All bank having self Illuminated Red-Green (ON-OFF) push buttons.

4 Nos. 50 KVAR capacitor Bank with discharge resistor.

7 Nos. 25 KVAR capacitor Bank with discharge resistor.

1 No. 20 KVAR capacitor Bank with discharge resistor.

4 No. 10 KVAR capacitor Bank with discharge resistor.

3 No. 5 KVAR capacitor Bank with discharge resistor.

Supply Receiving, fixing, testing & commissioning of of Capacitor panel as described above

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

STAFF QUARTER METER BOARD

Incoming

1 No. 250. Amps 4 Pole MCCB and ON/OFF/Trip & shunt trip coil.

Digital energy meter (conzerve – EM 6400NG with RS-485 or equivalent) of accuracy class-I, with 3 Nos. 250/5 amps 15VA CTs.

Phase indicating light shall be protected by suitable rating MCB’s.- 3 Sets

Breaker ON / OFF / TRIP indicating lights with control MCB’s. - 1 Set

Bus Bars

400 amps TPN Aluminium bus bars with colour coded heat shrinkable insulating sleeves - 1 Set.

Outgoing

34 No.63 Amps FP Pole MCB.

32 No. 2ph 2 wire Prepaid Meter.

Panel as described above.

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

PRINCIPAL QUARTER METER BOARD

Incoming

1 No.63 Amps 4 Pole MCCB and ON/OFF/Trip & shunt trip coil.

Phase indicating light shall be protected by suitable rating MCB’s.- 3 Sets

Breaker ON / OFF / TRIP indicating lights with control MCB’s. - 1 Set

1 No. 3ph 4 wire Prepaid Meter.

Bus Bars

300 amps TPN Aluminium bus bars with colour coded heat shrinkable insulating sleeves - 1 Set.

Outgoing

3 No.40 Amps FP Pole MCB.

Panel as described above.

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

STUDENT RESOURCE CENTRE MDB

1 No.315 Amps 4 Pole MCCB and ON/OFF/Trip & shunt trip coil.

Digital energy meter (conzerve – EM 6400NG with RS-485 or equivalent) of accuracy class-I, with 3 Nos. 300/5 amps 15VA CTs.

Phase indicating light shall be protected by suitable rating MCB’s.- 3 Sets

Breaker ON / OFF / TRIP indicating lights with control MCB’s. - 1 Set

Bus Bars

300 amps TPN Aluminium bus bars with colour coded heat shrinkable insulating sleeves - 1 Set.

Outgoing

9 No.63/100/125Amps TPN MCCB and ON/OFF/Trip & shunt trip coil.

Panel as described above.

AUDI CUM HALL MDB

1 No.400 Amps 4 Pole MCCB and ON/OFF/Trip & shunt trip coil.

Digital energy meter (conzerve – EM 6400NG with RS-485 or equivalent) of accuracy class-I, with 3 Nos. 400/5 amps 15VA CTs.

Phase indicating light shall be protected by suitable rating MCB’s.- 3 Sets

Breaker ON / OFF / TRIP indicating lights with control MCB’s. - 1 Set

Bus Bars

500 amps TPN Aluminium bus bars with colour coded heat shrinkable insulating sleeves - 1 Set.

Outgoing

6 No.63/100Amps TPN MCCB and ON/OFF/Trip & shunt trip coil.

2 No.250Amps TPN MCCB and ON/OFF/Trip & shunt trip coil.

Panel as described above.

DEGREE COLLEGE MDB

2 nos. 800 amps 4 pole electrically operated manually draw out type air circuit breaker each with following accessories :

Digital energy meter (Schneider – EM6400NG or equivalent) of accuracy class-1, with 3 Nos. 1000 amps 15VA CTs.

Phase indicating light shall be protected by suitable rating MCB’s. - 3 Sets

Breaker ON / OFF / TRIP indicating lights with control MCB’s. - 1 Set

Bus Bars

1250 amps TPN Aluminium bus bars with colour coded heat shrinkable insulating sleeves - 1 Set.

Bus Coupler

1000 amps 4 pole electrically operated manually drawout type air circuit breaker, with ON / OFF / TRIP indicating lamps with control MCB’s, shunt trip.

Outgoing

2 No.630Amps TPN MCCB and ON/OFF/Trip & shunt trip coil.

2 No.400/500Amps TPN MCCB and ON/OFF/Trip & shunt trip coil.

5 No.315Amps TPN MCCB and ON/OFF/Trip & shunt trip coil.

4 No.125Amps TPN MCCB and ON/OFF/Trip & shunt trip coil.

2 No.63Amps TPN MCCB and ON/OFF/Trip & shunt trip coil.

Panel as described above.

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

DEGREE COLLEGE SDB (FIRST/SECOND/THIRD FLOOR)

1 No.400/500 Amps 4 Pole MCCB and ON/OFF/Trip & shunt trip coil.

Digital energy meter (conzerve – EM 6400NG with RS-485 or equivalent) of accuracy class-I, with 3 Nos. 300/5 amps 15VA CTs.

Phase indicating light shall be protected by suitable rating MCB’s.- 3 Sets

Breaker ON / OFF / TRIP indicating lights with control MCB’s. - 1 Set

Bus Bars

500 amps TPN Aluminium bus bars with colour coded heat shrinkable insulating sleeves - 1 Set.

Outgoing

6 No.63/100/125Amps TPN MCCB and ON/OFF/Trip & shunt trip coil.

Panel as described above.

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

LIFT PANEL

Incoming

1 No. 125 Amps with 4 Pole MCCB with 125A ATS and ON/OFF/Trip

Digital energy meter (conzerve – EM 6400NG with RS-485 or equivalent) of accuracy class-I, with 3 Nos. 120/5 amps 15VA CTs.

Phase indicating light shall be protected by suitable rating MCB’s.- 3 Sets

Breaker ON / OFF / TRIP indicating lights with control MCB’s. - 1 Set

Bus Bars

300 amps TPN Aluminium bus bars with colour coded heat shrinkable insulating sleeves - 1 Set.

Outgoing

2 No. 40/63 Amps 4 Pole MCCB and ON/OFF/Trip

2 No. 32/25 Amps FP Pole MCB.

Panel as described above.

UPS MDB DEGREE/ADMIN COLLEGE BLOCK

Incoming

1 No.250/315 Amps 4 Pole MCCB and ON/OFF/Trip & shunt trip coil.

Digital energy meter (conzerve – EM 6400NG with RS-485 or equivalent) of accuracy class-I, with 3 Nos. 250/315/5 amps 15VA CTs.

Phase indicating light shall be protected by suitable rating MCB’s.- 3 Sets

Breaker ON / OFF / TRIP indicating lights with control MCB’s. - 1 Set

BUSCUPLER

1 No.250/315 Amps 4 Pole MCCB and ON/OFF/Trip & shunt trip coil.

Bus Bars

400 amps 4P Copper bus bars with colour coded heat shrinkable insulating sleeves - 1 Set.

Outgoing

9 No.63/100/125 Amps TPN Pole MCCB.

Panel as described above.

EXTERNAL LIGHTING FEEDER PILLAR OUT DOOR TYPE

INCOMER

1 Nos. 63/100Amp 16KA 4P MCCB complete having microprocessor based over current, short circuit & earth fault protection incomer shall be complete with following.

1 Nos. 60Amp AC3 4P Contactor with timer be complete as required.

METERING FOR EACH INCOMER

3 Nos. Cast resin current transformers of Class 1.0 for metering.

Three phase indicating lamps (LED type) with MCB.

ON OFF TRIP indicating lamps (LED type).

BUSBAR

1 Set of 100A, TPN Aluminum bus bars with colour coded sleeves.

OUTGOING UNITS

10 Nos. 6/32Amp TPN MCB 10KA

EXTERNAL LIGHTING FEEDER PILLAR AS DESCRIBED ABOVE

EM. D.G PANEL

INCOMER

1 No.500 Amps 4 Pole MCCB and ON/OFF/Trip & shunt trip coil.

1 No.500 Amps 4 Pole ATS

Digital energy meter (conzerve – EM 6400NG with RS-485 or equivalent) of accuracy class-I, with 3 Nos. 500/05 amps 15VA CTs.

Phase indicating light shall be protected by suitable rating MCB’s.- 3 Sets

Breaker ON / OFF / TRIP indicating lights with control MCB’s. - 1 Set

Bus Bars

400 amps 4P Copper bus bars with colour coded heat shrinkable insulating sleeves - 1 Set.

Outgoing

1 No.315 Amps TPN Pole MCCB.

2 No.200/250 Amps TPN Pole MCCB.

1 No.125 Amps TPN Pole MCCB.

3 No.63/100 Amps TPN Pole MCCB.

PANEL AS DESCRIBED ABOVE

EM. PANEL DEGREE COLLEGE

INCOMER

1 No.250 Amps 4 Pole MCCB and ON/OFF/Trip & shunt trip coil.

Digital energy meter (conzerve – EM 6400NG with RS-485 or equivalent) of accuracy class-I, with 3 Nos. 250/05 amps 15VA CTs.

Phase indicating light shall be protected by suitable rating MCB’s.- 3 Sets

Breaker ON / OFF / TRIP indicating lights with control MCB’s. - 1 Set

Bus Bars

300 amps 4P Copper bus bars with colour coded heat shrinkable insulating sleeves - 1 Set.

Outgoing

5 No.125 Amps TPN Pole MCCB.

3 No.63/100 Amps TPN Pole MCCB.

PANEL AS DESCRIBED ABOVE

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

EM. PANEL SCR/AUDI

INCOMER

1 No.100/125 Amps 4 Pole MCCB and ON/OFF/Trip & shunt trip coil.

Digital energy meter (conzerve – EM 6400NG with RS-485 or equivalent) of accuracy class-I, with 3 Nos. 100/05 amps 15VA CTs.

Phase indicating light shall be protected by suitable rating MCB’s.- 3 Sets

Breaker ON / OFF / TRIP indicating lights with control MCB’s. - 1 Set

Bus Bars

300 amps 4P Copper bus bars with colour coded heat shrinkable insulating sleeves - 1 Set.

Outgoing

5 No.63/100 Amps TPN Pole MCCB.

PANEL AS DESCRIBED ABOVE

SUB HEAD-VI EARTHING & LIGHTING PROTECTION

Earthing with G.I. Earth plate 600 mm x 600 mm x 6 mm thick including accessories and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc. ( with charcoal or coke and salt).

Earthing with copper . Earth plate 600 mm x 600 mm x 3 mm thick including accessories and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc.( with charcoal or coke and salt).

Supplying and laying 6 SWG G.I. wire at 0.50 metre below ground level for conductor earth electrode, including solding etc. as required.

Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe from earth electrode including connection with G.I. nut, bolt, spring, washer excavation and re-filling etc. as required.

Providing and fixing 25x5 mm copper strip in 40mm dia G. I. pipe from earth electrode including connection with brass nut, bolt, spring washer excavation and re-filling etc. as required.

S/L 25x6mm G.I. earth strip in ground: Proving and laying earth connection from earth electrode with 25x6mm G.I wire in 15mm GI pipe from electrode as required.

Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. as required.

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.

Providing and fixing 32 mm X 6 mm G.I. strip on surface or in recess for connections etc. as required.

Providing and fixing 50 mm X 6 mm G.I. strip on surface or in recess for connections etc. as required.

Providing and fixing 50 mm X 6 mm Cu, strip on surface or in recess for connections etc. as required.

CU WIRE CONDUCTORS

Providing and laying following size CU insulated wire on surface or in recess in exising conduit/ cable tray for connections etc. as required.

6sqmm ISI marked, FRLS PVC insulated, 1 core copper conductor

10sqmm ISI marked, FRLS PVC insulated, 1 core copper conductor

16sqmm ISI marked, FRLS PVC insulated, 1 core copper conductor

LIGHTNING PROTECTION

Prividing and Fixing of GI lightning conductor Finial made of 25mm dia 300 mm Long GI tube , having single prone on top with 85mm dia 6mm thick GI base plate including holes etc complete as required

Providing and fixing GI-tape 20 mm x 3 mm thick on parapet or surface of wall for lightning conductor as required.(for vertical run)

Providing and fixing GI-tape 20 mm x 3 mm thick on parapet or surface of wall for lightning conductor as required.(for horizontal)

Providing and fixing testing joint, made of 20 mm x 3 mm thick gi strip, 125 mm long with 4 Nos. brass bolts, nuts check nuts and spring washers etc. complete as required.

Providing and laying GI tape, 32 mm x 6 mm thick from earth electrode directly in ground as required.

Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required.

SUPPLY AND INSTALLATION OF LIGHT FIXTURES AND EXHAUST FANS

SITC of following ratings LED Flood lighting luminaire with pressure dia cast housing and toughned glass cover IP 66 protection) in existing pole / pipe for supply voltage 100 ,270v AC , 5o HZ luminaire shall be confirm to IS 10322 part 5/ section 3e and shall be complete with all necessary accessories as required

45W LED STREET LIGHT

SITC of following ratings LED Flood lighting luminaire with pressure dia cast housing and toughned glass cover IP 66 protection) in existing pole / pipe for supply voltage 100 ,270v AC , 5o HZ luminaire shall be confirm to IS 10322 part 5/ section 3e and shall be complete with all necessary accessories as required

50/60W LED FLOOD LIGHT

SITC of following ratings RECCESS /SURFACE MOUNTED LED ROUND / SQUIRE SHAPE DOWN LIGHT liminiaire with pressure dia cast housing FOR SINLE PHASE supply voltage luminaire shall be confirm to IS 10322 Part 3 section 2 or IEC 6-7 22 with all necessary accessory item required .

10/12 W LED ROUND SURFACE DOWNLIGHT

15/16w LED RECESSED ROUND DOWNLIGHT

50/60w LED FLOOD LIGHT D.HIGHT AREA

2'x2' LED PANEL LIGHT

10/12w LED WALL LIGHT

28w LED RECESSED BATTEN LIGHT

50w LED RECESSED DOWN LIGHT

6w LED SURFACE BULK HEAD LIGHT

SITC of following ratings SURFACE MOUNTED LED tube light fitting, suitable for 230V 50Hz, single phase supply etc. complete as required.

10/12W LED Tube light

20/22W LED Tube light

SITC of following ratings LED Post top lamp made in dia cast aluminium housing with decorative clear/ opal acrylic diffuse on existing pipe including connection with 1.5sq mm copper conductor etc all complete as required.

20/25W LED post top lamp clear

SITC of following ratings approved make LED Bollard fitting, with rectangular shape of height 600 to 850mm power input 8/9 watt with dia cast aluminium housing opel with PC diffuser, [P:65/54 protection, confirming to IS:10322 part 5 etc all complete as required (excluding plinth charge)

LED strip light 24 volts DC with IP 65 rated in different colours of length 5 mtr and power 5 W per meter including driver IS: 10322 pert 5/ section-7.

Supply of LED Mirror Light with power 8/10W rated voltage 230V 50 Hz aluminium/ PC body with rauuning life minimum 30000 Hours

Supply insttalation , testing and commisioning of following size ceiling fan 3 balde confirming to IS : 374:2019 incuding wiring thedown roads of standed lenth ( upto 30 cm ) with 1.5 sqmm PR PVC, insulated copper wire suitable for 230V 50Hz single phase supply etc. compleyte as required.

1200mm (48 Degree) BLDC 5 star rating 32W ceiling fan

Supply and fixing of step type electronic fan regulator on existing modular plate switch box including connection but excluding modular plate etc as required.

Installation, testing and commissioning of ceiling fans/bracket fan of all sizes including wiring the down rod .of standard length (up to 30 cm ) with 1.5 sq.mm FR PVC insulated copper conductor single core cable etc as required.

Supply of 12" (300mm) metal exhaust fan

Supply of 16" (400mm) metal exhaust fan

TELEPHONE, TV , DATA cabling with Raceways :

Supply & fixing of following Items:-

Supply & fixing of modular telephone cord outlet & switch box including connections but excluding modular plate etc. as required.

Supply & fixing of modular TV antenna socket outlet & switch box including connections but excluding modular plate etc. as required.

S/F Modular boxes, base & cover plate :- Supplying and fixing following size / modules , GI box along with modular base & cover plate for modular switches in recess etc as required.

I or 2 module (78mmx 78mmx 45mm)

Supplying and fixing of following size PVC conduit alongwith the accessories in surface / recess including painting in case of surface conduit or cutting and making good the same in case of recessed conduit as required as per specification.

20mm dia

25mm dia

32mm dia

Supply and fixing 1 or 2 module ( 75mm X 75mm ) GI Box along with modular base and cover plate for modular switches in recess etc as required

Supply and fixing of Computer terminal (RJ-45) outlet in existing box with modular plate

Supply and fixing of Outdoor type junction Box

Supply and Laying of Cat-6 Cable in existing conduits

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm copper conductor PE insulated, with PVC shield in the existing surface/ recessed PVC conduit as required.

Supplying, drawing, of 0.5mm dia (2 pair) FR PVC insulated copper conductor , unarmoured telephone cable in existing surface/ recessed PVC conduit as required

Supplying, drawing, of 0.5mm dia (4 pair) FR PVC insulated copper conductor , unarmoured telephone cable in existing surface/ recessed PVC conduit as required

Supplying and Fixing in floor with all accessories , 2 mm thick steel sheet factory fabricated post galvanized floor recessed raceway of the following sizes

225 mm wide x 38 mm deep raceway

100 mm wide x 38 mm deep raceway

Providing and fixing 400 x 400 x 50 mm deep 2 mm thick GI sheet junction box including providing 3 mm thick stainless steel cover as required

Providing and fixing 300 x 300 x 50 mm deep 2 mm thick GI sheet junction box including providing 3 mm thick stainless steel cover as required

Providing and fixing 150 x 150 x 50 mm deep 1.6 mm thick GI sheet junction box including providing 3 mm thick stainless steel cover as required

SUB HEAD- IX- FIRE ALARM AND DETECTION SYSTEMS

Supplying and fixing of following sizes of steel conduit along with accessories in surface/recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required.

20mm dia

25mm dia

Supplying and laying of following sizes FR PVC insulated single core copper wire in existing conduit complete as required.

2x1.5 sq mm

2x2.5 sq mm

Ten Loop Panel

Two Loop Panel

Supplying, installation, testing & commissioning of repeater panel wih 320 character/ Touch screen LCD display with inbuilt reset, acknowledge and silence switches complete as required.

Supplying, installation, testing & commissioning of intelligent analog addressable photothermal detector complete with mounting base complete as required.

Supplying, installation, testing & commissioning of response indicator on surface/recessed MS Box having two LED, metallic cover complete with all connections etc as required.

Supplying, installation, testing & commisssioning of intelligent addressable programmable sounder complete as required.

Supplying, installation, testing & commissioning of fault isolator complete with base as required.

Supplying, installation, testing & commissioning of intelligent addressable thermal detector with rate of rise cum fixed tempreature thermistor complete with base as required.

Supplying, installation, testing & commissioning of addressable fire control module complete as required.

Supplying, installation, testing & commissioning of addressable manual call point complete as required.

Supplying, installation, testing & commissioning of addressable horn cum strobe complete as required.

PA SYSTEM

Supplying, installation, testing & commissioning of 6 zone, voice alarm controller with USB, MP3 player (including 6 zone button paging station) with seamless integration facility with main fire alarm panel for voice evacuation complete as required..

Supplying, installation, testing & commissioning of 1.5/3/6W ceiling speaker complete as required.

Supplying, installing, testing and commissioning of 2X1.0 SQMM IND. 1.1KV SPEAKER CABLE in existing conduit.

Supplying, installation, testing & commissioning of ceiling/wall mounted loud speaker, 3/1.5 Watt in ABS enclosure complete as required.

Supplying, installation, testing & commissioning of digital audio amplifier 50 Watt, 25V rms operating at 240 volt AC supply complete as required.

Supplying, installation, testing & commissioning of digital audio amplifier 75 Watt, 25V rms operating at 240 Volt AC Supply complete as required.

Supplying, installation, testing & commissioning of Voice command keypad 6 zone, with microphone assembly complete as required.

Providing and fixing of self illuminated / auto glow "EXIT" signs printed on photoluminescent sheet containing self illuminated base chemical, of appropriate size not less than 300 x 150 mm, suspended from ceiling or fixed to the walls with accessories as required and as directed at site

INTERNAL WIRING AND FINAL DISTRIBUTION BOARDS

Wiring for Light point / Fan point / Exhaust Fan point / Call Bell point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface / recessed PVC conduit , with modular switch ,modular plate ,suitable GI box as required

Group - B

Group - C

Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed steel conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc. as required.

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.

S.P 5/6 amps, one way modular switch, ISI Marked

S.P 15/16 amps, one way modular switch, ISI Marked

5 pin 5/6 amps, modular socket Outlet, ISI Marked

6 pin 15/16 amps, modular socket Outlet, ISI Marked

Supplying and fixing 20 amps, 240 volts, SPN industrial type, socket outlet, with 2 pole and earth, metal enclosed plug top alongwith 20 amps “C” curve, SP, MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.

Supplying and fixing 20/25 amps, 415 volts, TPN industrial type, socket outlet, with 4 pole and earth, metal enclosed plug top alongwith 30 amps “C” curve, TP, MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.

Supplying and fixing Brass Batten/ Angle holder including connections etc. as required.

DB SUBMAIN WIRING IN STEEL CONDUITS

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FR PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required.

2 X1.5 sq. mm + 1 X 1.5 sq. mm earth wire Metre

2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire Metre

2 X 4 sq. mm + 1 X 4 sq. mm earth wire Metre

2 X 6 sq. mm + 1 X 6 sq. mm earth wire Metre

2 X 10 sq. mm + 1 X 6 sq. mm earth wire Metre

2 X 16 sq. mm + 1 X 6 sq. mm earth wire Metre

4 X 6 sq. mm + 2 X 6 sq. mm earth wire Metre

4 X 10 sq. mm + 2 X 6 sq. mm earth wire Metre

4 X 16 sq. mm + 2 X 6 sq. mm earth wire Metre

POWER SOCKETS

Supplying and fixing suitable size GI box with modular plate and cover in Front on surface or in recess ,including providing and fixing 3 pin 5 / 6 amps modular socket outlet and 5 / 6 amps modular switch,connection, painting etc.as required.

Supplying and fixing suitable size GI box with modular plate and cover in Front on surface or in recess ,including providing and fixing 6 pin 15 / 16 modular socket outlet and 15 / 16 amps modular switch,connection,painting etc.as required.

FINAL DISTIRIBUTION BOARD

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess,complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted includingearthing etc. as required. (But without MCB/RCCB/Isolator)

8 way Double Door

12 way Double Door

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)

6 way Double Door

8 way Double Door

12 way Double Door

Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer ) asrequired . (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.)

6 way Double Door

12 way Double Door

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing following rating, double pole, (single phase and neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. asrequired.

Providing and fixing following rating and breaking capacity and 4 pole MCB with thermomagnetic release and terminal spreaders with cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required.

25-63A 16KA fixed thermal setting

IP BASED CCTV SYSTEM

Supply, installation, testing and commissioning of UL Listed 1.3 Megapixel CMOS Vandal-proof, Network Dome Camera (1280 × 960) resolution, 1/3” Progressive scan CMOS, [email protected], AGC ON. 0 Lux with IR on, IR cut filter with auto switch, IR range up to 30 mtrs, H.264 / MJPEG, Dual stream, motion detection, Bit rate 32 Kbps-16Mbps, 3D DNR, DWDR, 12 VDC ± 10%, PoE , IP66, K-10, with fixed lens between (2.5 - 12mm), size of lens shall be as per site requirement & mockup. ONVIF, SIP, NMS, Profile S supported, connectors complete as required in dome shape fixed type for mounting recessed in false ceiling or mounted on wall complete as required.

Supply, installation, testing and commissioning of UL Listed 1.3 Megapixel CMOS, Vandal-proof, Network Bullet Camera,(1280x960)resolution, 1/3” Progressive scan CMOS, [email protected], AGC ON. 0 Lux with IR on, IR cut filter with auto switch,, H.264 / MPEG4 , Dual stream, Bit rate 32 Kbps-16Mbps, Standard IP66, PoE , with Fixed Lens between (2.5 - 12mm), size of lens shall be as per site requirement & mock-up ,IR range Up to 50 mtr, motion detection, with ONVIF, SIP, NMS, Profile S supported, connectors complete as required IR Bullet fixed type for mounting on wall or surface mounted with back box and adapter plate complete as required.

Supply, installation, testing and commissioning of Professional Video management and recording software and hardware comprising 32Ch. NVR to record output of all cameras mentioned above in Item no 1,2,3 Third-party network cameras supported, H.264 Compression - Up to 5 Megapixels resolution recording, multiple Hard Disk 8 SATA with each having maximum storage capacity of 6 TB , as required for minimum 30 days recording required for recording when in 80% motion @ 720p 25 Frames per second(Real Time) or for recording when not in motion @720p 12.5 Frames per second, with RAID-5 Storage ,10/100/1000 MBps network interface with each NVR, 2 USB2.0, HTTP Networkable, backup by USB/DVDWR, required Client software included, 6 Nos Client licenses and required Camera licenses for each camera complete as required. All the components to be of same make as Camera.

Supply,installation,testing and commissioning of 32” CCTV colour LED screen including all accessories complete as required.

Supply, installation, testing and commissioning of Layer 3 switch HP/ Cisco make with 16 ports PoE managed, 10/100/1000 EB core switches to support all IP cameras & Access Control System , with 2 Fibre uplinks Port module only complete as required.

Supply, installation, testing and commissioning of Layer 2 switch HP/ Cisco make with 32 ports PoE managed, 10/100/1000 EB core switches to support all IP cameras & Access Control System , with 2 Fibre uplinks Port module only complete as required.

Supplying and installation of 19" 42U APW President Rack with glass front door, steel rear door, power supply, MCB, cable manager, drawer shelves and wiring channels to accommodate systems equipment and accessories as mentioned in the BOQ above and including all connections and terminations as required

Supply and Laying of 3C-2.5 Sq. mm unarmoured copper Power Cable in existing conduits for Cameras power supply

Supply and Laying of 3C-1.5 Sq. mm unarmoured copper Power Cable in existing conduits for Cameras power supply

Supplying and fixing of following size PVC conduit alongwith the accessories in surface / recess including painting in case of surface conduit or cutting and making good the same in case of recessed conduit as required as per specification.

20mm dia

25mm dia

32mm dia

SUB HEAD XII-UPS/INV/SOALR SYSTEM

1650VA sine wave inverEr input AC range.1fi)V to 300V AC, wide- 90V to 300V AC, standard - 180V to 260V AC, DC range - 10.5 to 14.2 efficiancv- 80%, protection-overload, Short circuit

Trolly for Double tubular Battery

200Ah tubular Lead acid battery with 36 month replacement guaranty. IS:1652:1991

3000VA sine wave inverter input AC range-1O0V to 300V AC, wide- 90V to 300V AC, standard - 180V to 260V AC, DC range -1.0.5 toL4.2, efficiancv- 80%, protection-overload, Short circuit

Trolly for Double tubular Battery

200Ah tubular Lead acid battery with 36 month replacement guaranty. IS:1652:1991

Supply,Installation, Commissioning & Training of 40 KWp Grid Connected Rooftop Solar Photovoltaic System based on heterojunction technology solar PV module as per requirment. including all expenses (to be borne by bidder) e.g. Air Fare, Local Transport, accommodation etc.

UPS SETS

100 KVA online UPS three phase input and three phaseoutput power system of input, Htug" range 360V/3 IOV/ 4Cf.V/ 48hiai, fieqrenry range 40Hz - 6OHz !.70%t output Voltage range 415V t 1%, Frcquency range 50Hz t 1%, Power Factor 0.8/3:1, Harmonic distrortion - < 2% THD (Linear load) : 5% THD (non-liniear load)

30 KVA online UPS three phase input and three phase output power system of input, Voltage range 360V/380Y / 400Y / 485V AC, Frequenry range 40Hz - 60Hz + L0%, output Voltage range 415V + 1%, Frequency range 50Hz + 1%, Power Factor 0.8/3:1, Harmonic distrortion - < 2% THD (Linear load) : 5% THD (non-liniear loa

15 KVA online UIIS three phase input and single phase output power system of input Voltage range 110V AC I 5% - 300V AC r 5%, Frequenry range 40Hz - 60H'2, Power Factor > 0.90 @ full load, and outputVoltage range 200y /208/220/?30/240Y AC, Voltage regulation t 1%, Frequency range 50Hz t 0.25H2 or 6OHz x .3OHz Harmonic distrortion - < 2% T}{D (Linear load) : 4% TIID (non-liniear load) efficencv- 88/83Y

HVAC WORK

Supply Installation,Testing & Commissioning of modular type Variable Refrigerant Flow/Variable Refrigerant Volume air cooled Outdoor units suitable for cooling and heating,having all hermetically sealed inverter type Scroll Compressor(s),minimum two compressors for above 14 HP modules, microprocessor based Controller,top discharge type condensing unit(s),with R410A Refrigerant,vibration isolators,with suitable foundation etc.complete as required.The unit shall deliver the rated capacity at AHRI Conditions and work even at 50°C ambient temperature without tripping.The unit shall be suitable to work on 400V+/-10%,3Phase,50Hz AC power supply. The unit shall be filled with first charge of the refrigerant and ready for use as required. The unit shall be filled with first charge of the refrigerant and ready for use as required.The COP at AHRI conditions shall not be less than 3.1 and IEER not less than 6.5.

Provision of power supply to each outdoor unit shall be provided with MCCB of suitable rating in IP 65 enclosure with suitable size of copper cable. Single source of power supply shall be provided by the client

26 HP OUTDOOR UNIT

20 HP OUTDOOR UNIT

18 HP OUTDOOR UNIT

LOW SIDE EQUIPMENTS

Indoor VRV Units (celling mounted ductable type unit)

Supply,installation,testing and commissioning of following minimum capacity 4-way flow VRV/VRF CassetteType Indoor ceiling mounted unit (Sensiflow Type ) equipped with synthetic washable media pre- filter, fan section with low noise fan/dynamically balanced blower,multi speed motor,coil section with DX Copper coil,electronic expansion valve,outer cabinet,drain pump,grill,necessary supports,vibration isolation,cordless remote control etc.,suitable for operation on single phase 230V±10%,50 Hz AC supply,complete,as required.The unit shall have automatic force shutdown provision in case of fire on receiving signal.The cooling capacity of indoor unit will be at air inlet conditions of 27 Degree DB and19 Degree C WB temperature

1x1.0 TR Four Way Cassette Type Unit (Sensiflow Type units )

Supply Installation, testing and commissioning of Y-joints of suitable size as per site requirements.

Supply Instalaltion, testing and commissioning of self diagnostic type remote controllers. Cordedless Type

CENTRALISED CONTROLLER

Supply testing and commissioning of main centralised controller as per specifications to hook up indoor units as mentioned . Controller shall have unified ON -OFF and schedule timer feature.Controller shall however, be suitable for minimum 64 groups of indoor units. Controller shall be suitable to autosequence the outdoor as well as indoor units catering to Server Room and UPS room as required.

Supply testing and commissioning of duct mounted air purification system based on Photo Hydroxylation Technology which consists of quad metalic compound to reduce the harmful microorganisms such as bacteria, virus, fungi, mold, PM 10, PM 2.5, etc and chemical substances like VOCs and harmful gases. The unit should have UVC lamps of 254 nm wavelength covered by cylndrical catalyst and nano filter. The unit should have a life of 18000 hours. The unit shouold be installed in the supply air duct for better results. The unit should be able to reduce more than 90% of PM 2.5. Approved Makes : Aeroshield / Crystal Purifiers

All Ac Units

Double Skinned Ceiling suspended/Floor Mounted Air Handling Units with thermal break profile with VFD

Supply, installation, testing and commissioning of factory fabricated Double Skinned DX TYPE Air- handling unit Floor Mounted/Ceiling Suspended fabricated out of extruded aluminium section with 0.63mm pre-plasticized / pre-coated Galvanised steel sheet outside & 0.63 mm plain Galvanised steel sheet inside with blower, blower section and blower motor TEFC type suitable for operation on 415 volts ± 10%, 50 Hz ± 5% AC supply, 4 Row DX type cooling coil made of Aluminium finned Copper tube with coil section,with following filtration level, polished stainless steel drain pan made out of 22 G sheet duly insulated complete with motor and belt drive package etc. without face and bypass dampers. The AHU panels shall be insulated with 48mm thick & 48 Kg/m³ density PU foam.The motor & blower assembly shall be mounted on Aluminium extruded section only

The face velocity across cooling coil shall be limited to 152 MPM maxm.

Pre-filter section with Pre filter(10 Micron & 90 % Efficiency) in All following AHUS

Expansion device with control box ,communication kit ,remote control & accessories for AHU kit

Fan Oulet Velocity Not to Exceed 8.5 m/s

6 RD Cooling Coil (CC)

CS AHU 4000 CFM /13 TR/50 MM STATIC/6RD

CS AHU 5000 CFM /16 TR/50 MM STATIC/6RD

FM AHU 12000 CFM /13 TR/50 MM STATIC/6RD

FM AHU 20000 CFM /13 TR/50 MM STATIC/6RD

MECHNICAL VENTILATION SYSTEM

TUBE/VANE AXIAL FLOW FANS FOR NORMAL AS WELL AS FIRE MODE (FRESH AIR FAN) WITH STATER PANEL

Supply, installation, shifting, loading, unloading, testing & commissioning of floor mounted, double flanged, long casing (motor should completely accommodated inside the Fan casing) axial flow fans confirming to BSEN12101 standard (Fire Rated) AMCA Certified (all offered pitch angle certified by AMCA and listed on AMCA website), with adjustable pitch blade at site & angle (Welded Blades shall not be acceptable), bird screen at fan outlet , MS/GI casing, cast aluminium alloy impeller complete with TEFC Sq. Cage Induction motor suitable for 415 volts ± 10%, 50Hz ± 3 %, 4/6/8 pole, three Phase, A.C supply class "H" insulation with support, Phase& Motor rated Value IP55 . Motor shall be Thermally Rated for 240 deg C for 2 Hours & direct driven for smoke extraction fans.

With the Approx. Motor HP as given below (to be supported with Documentary evidence at the time of Technical Bid.)

Normal application fans should be "Vane Axial" type.

The rate shall include supply and fitting of vibration isolators ( spring & rubber pads) complete as per specifications and drawings including fitting of accessories like Fire retardant canvass connection painting,bird screen etc. as required at site of work. Including all type of civil work like cutting/holes/chasing/cut out in brick wall etc

1. Outlet Velocity for normal fans not to exceed 17.0 MPS

2. Total efficiency of normal fans shall not less than 60%

3. Fan motor shall meet IE3 standard as per IS-12615

AXIAL FAN/FRESH AIR /6500 CFM /3.7 KW /30 MM/ Not exceed 70 db. at 3 meter distance /3 PHASE /NORMAL MODE

AXIAL FAN/FRESH AIR /9000 CFM /3.7 KW /30 MM/ Not exceed 70 db. at 3 meter distance /3 PHASE /FIRE MODE

AXIAL FAN/FRESH AIR /10000 CFM /3.7 KW /30 MM/ Not exceed 70 db. at 3 meter distance /3 PHASE /FIRE MODE

TUBE AXIAL FLOW FANS FOR NORMAL AS WELL AS FIRE MODE (EXHAUST AIR FAN)

Supply, installation, shifting, loading, unloading, testing & commissioning of floor mounted, double flanged, long casing axial flow fans confirming to BSEN12101 standard (Fire Rated) AMCA Certified, with adjustable pitch blade & angle, bird screen at fan outlet , MS/GI casing, cast aluminium alloy impeller complete with TEFC Sq. Cage Induction motor suitable for 415 volts ± 10%, 50Hz ± 3 %, 4/6/8 pole, three Phase, A.C supply class "H" insulation with support, Phase& Motor rated Value IP55 . Motor shall be Thermally Rated for 240 deg C for 2 Hours & direct driven for smoke extraction fans.

With the Approx. Motor HP as given below (to be supported with Documentary evidence at the time of Technical Bid.)

The rate shall include supply and fitting of vibration isolators ( spring & rubber pads) complete as per specifications and drawings including fitting of accessories like Fire retardant canvass connection painting,bird screen etc. as required at site of work. Including all type of civil work like cutting/holes/chasing/cut out in brick wall etc

1. Outlet Velocity for normal fans not to exceed 17.0 MPS

2. Total efficiency of normal fans shall not less than 60%

3. Fan motor shall meet IE3 standard as per IS-12615

AXIAL FAN/FRESH AIR /6500 CFM /3.7 KW /30 MM/ Not exceed 70 db. at 3 meter distance /3 PHASE /NORMAL MODE

AXIAL FAN/FRESH AIR /10000 CFM /3.7 KW /30 MM/ Not exceed 70 db. at 3 meter distance /3 PHASE /FIRE MODE

PIPING WORK

Supply,Installation,testing and commissioning including vaccumiazation and Nitrogen testing of following nominal sizes of soft/harddrawn copper refrigerant piping for VRV/VRFsystem,complete with fittings,with suitable adjustable ring type hanger supports,jointing/brazing including accessories,insulated with XPLE Class-O tubular insulation/with Class-O closed cell elastometric nitrile rubber tubular sleeves sections of specified thickness as given below for Suction and Liquidlines,all accessories as per specifications etc. as required :

41.27 mm dia(OD) (Hard drawn) with tube thickness 1.62 mm with19 mm thick insulation

34.9 mm dia(OD)(Hard drawn) with tube thickness1.62 mm with 19 mm thick insulation

28.58 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19 mm thick insulation

22.2 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19 mm thick insulation

19 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19 mm thick insulation

15.86 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with19 mm thick insulation

12.7 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with19 mm thick insulation

9.5 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with19 mm thick insulation

6.4 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with19 mm thick insulation

GSS RECTANGULAR DUCTING

Supply, Installation, Balancing & Commissioning of factory fabricated GSS sheet metal ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc finally applying fire rated paint as per BS 476 Part 24 . as per approved drawings and specifications of following sheet thickness complete as required.

splitter & vanes etc .shall be apart of ducting no extra cost shall be paid for the same .

0.63 mm sheet duct

0.80 mm sheet duct

1.0 mm sheet duct

1.25 mm sheet duct

Supply, Fabrication, installation and testing of GSS sheet metal ducts & finally applying fire rated paint as per BS 476 Part 24 (Site FABRICATED DUCTS For Connection /Plenum etc.) in accordance with the approved shop drawings complete with all accessories like vanes, flanges, suspension rods , anchor bolts, GI bolts & nuts, etc., as per specifications.

0.63 mm sheet duct

0.80 mm sheet duct

1.0 mm sheet duct

1.25 mm sheet duct

Supply, fabrication, installation and testing of 50 micron powder coated, aluminum extruded linear fixed horizintal bar/grill or diffusers with all side flanges as per approved shop drawings.

SSupply, installation, testing and commissioning of GI volume control duct damper complete with neoprene rubber gaskets, nuts, bolts, screws linkages, flanges etc, as per specifications.(18G)

Supply, Installation and Testing of 50 micron powder coated, Al extruded volume control damper for collor to be provided with suitable links and quadrants for control of volume of air.

Supply, fabrication, installation and testing of 50 micron powder coated, aluminum extruded fresh air louvers with bird screen & Al volumne control damper with all side flanges as per approved shop drawings.

INSULATION WORK.

Supply and installation of Insulation material shall be closed cell flexible elastomeric foam based on synthetic rubber composition with fire retardant properties.The insulation material shall have Microban®* an anti-microbial product, which is EPA (Environmental Protection Agency), USA Approved, as an integral part of insulation that cannot be washed off or worn off. The insulation material shall give enhanced level of protection against harmful Microbes such as fungi, bacteria & mold and should confirm to UL 181, ASTM G 21/C 1338. Thermal conductivity of insulation material shall not exceed 0.036 W/(m.K) at mean temperature of 24C as per ASTM C 177 / ASTM C 518. Water Vapor Permeability of insulation material shall be minimum 0.05 Perm-in. /0.725 x 10-13 Kg/[s.m.Pa] without any external barrier as per ASTM E 96. Procedure A. The insulation material shall have water absorption of 0.2% by volume as per ASTM C 209 / ASTM C 1763. The insulation material shall have fire performance rating of 25/50 as per ASTM E 84. The insulation material shall have fire performance rating of UL 94. The insulation material shall be self-extinguishing, does not drip, and does not spread flames. The insulation material need to comply with local Civil defence authority norms & should possess a valid approval. The insulation material shall be dust and fibre free. The insulation material shall be formaldehyde free. The insulation material shall be CFC & HCFC free. The insulation material shall meet ASHRAE 90.1-2010, ASHRAE Standard 189.1, NFPA 90A & NFPA 90B Standards. The insulation material shall withstand maximum surface temperature of +105 Deg.C and minimum surface temperature of -50 Deg.C as per ASTM C 534. The insulation material shall have ODP (Ozone Depletion Potential) and GWP (Global Warming Potential) of Zero. The insulation material shall be applied indoors. Coverings shall be used for exposed areas. Thickness of the insulation shall be as specified for the individual application. The insulation material shall be installed as per manufacturer’s recommendation.

13 MM Thick

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

ACOUSTIC INSULATION - FOR DUCT

Supply and Application of Acoustic Insulation Inside the Duct with Engineered Nitrile Rubber open cell foam with Density 140 - 180 Kg/m3 passing Class 1 Fire Performance test as per BS 476 Part 7 and with built-in EPA approved Microban antimicrobial protection; to be applied using manufacturer's recommended Rubber based Adhesive in a blend of solvents. , Metal Strips and Anchor Fasteners as per design.

15 mm thickness (Internal Lining of Ducts)

ELECTRICAL

CUBICAL PANEL BOARD

Panel should have following:

Indicating lights LED for incommer and outgoing

Panel With following Capacities:

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

18HP /20 HP/22HP/28HP OUTDOOR UNIT

ELECTRICAL WORK FOR MECHANICAL VENTILATION SYSTEM

ISOLATORS

Providing & fixing weather proof isolator with suitable rating near each unit, the prices should be inclusive of copper cabling from isolators to outdoor units.

POWER CABLING

Supplying, laying, effecting proper connections, testing & commissioning of the following sizes of 1.1 KV -Cross Linked Poly Ethelene armoured aluminium conductor cables conforming to relevant latest amended Indian Standards laid over MS supports & Cable Trays including clamping the cables to supports in an approved manner as required complete with all accessories.

3.5 Cx 25 Sqm Al Conductor

4.0Cx6 Sqm

4.0Cx10 Sqm

4C x 16 Sq. mm

COPPER POWER & CONTROL CABLING INCLUDING CABLE TRAY

Supply and laying ,testing and commissioning of following sizes of Copper conductor control cables with PVC conduit & fixing clamps and effecting proper connections to equipment etc. of following sizes :

3C x 1.5 sq. mm

3C x 2.5 sq. mm

3C x 4 sq. mm

Supplying and laying 6 SWG G.I. wire at 0.50 metre below ground level for conductor earth electrode, including connection/ termination with GI thimble etc. as required.

Supply & laying 25x5mm GI strip at 0.5mt below ground as strip earth electrde including connection/terminatng with GI nut,bolt,spring,washer etc as required.)jointing shall be done by overlapping &with 2sets of brass nuts bolt&spring washer spaced at 50mm)25mm x5mm

HORTICULTURE

Supplying and stacking of good earth at site including royalty and carriage up to 1 km (earth measured in stacks will be reduced by 20% for payment).

Supplying and stacking at site dump manure from approved source, including carriage up to 1.0 km (manure measured in stacks will be reduced by 8% for payment)

Screened through sieve of IS designation 20 mm

Screened through sieve of IS designation 16 mm

Screened through sieve of IS designation 4.75 mm

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

Supplying and stacking of well decayed cow dung manure at site including royalty and carriage up to 1.0 km (cow dung manure measured in stacks will reduced by 8% for Payment)

PREPARATION WORKS

Fine dressing of the ground

Mixing earth and sludge or manure in the required proportion specified or directed by the Engineer-in-charge

Spreading of sludge, dump manure and / or good earth in required thickness as per direction of Engineer-in-charge (cost of sludge, dump manure and / or good earth to be paid separately).

Uprooting rank vegetation and weeds by digging the area to a depth of 60 cm, removing all weeds and other growth with roots by forking repeatedly, breaking clods, rough dressing, flooding with water, uprooting fresh growths after 10 to 15 days and then fine dressing for planting new grass, including disposal of all rubbish with all leads and lifts

Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20% : 1 part of stacked volume of manure after reduction by 8%) flooding with water, dressing including removal of rubbish and surplus earth, if any, with all leads and lifts (cost of manure, sludge or extra good earth if needed to be paid for separately)

Holes 1.2 m diameter and 1.2 m deep

Holes 90 cm diameter and 90 cm deep

Holes 60 cm diameter and 60 cm deep

Holes 45 cm diameter and 45 cm deep

Providing and stacking of Delonix regia (Gulmohar) of height 150-165 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge.v

Providing and stacking of Cassia fistula (Amaltash) of height 120-135 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Ficus bengalensis (Bargad) of height 120-135 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Ficus religiosa (Peepal) of height 150-165 cm. in big poly bags of size 30 cm as per direction of the officer-in-charge.

Providing and stacking of Jasmine grandiflorum (chameli) of height 30 cm to 45 cm. in 20 cm size of Earthen pots / Plastic pots & as per direction of the officer-in-charge. .

Providing and stacking of Azadirachta indica ( Neem ) of height 120-130cm in big polybag of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Bauhinia purpurea (Kachnar) of height 150-165 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge

Providing and stacking of Callistemon lanceolatus of height 150-165 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge

Providing and stacking of Spathodea campanulata of height 150-165 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Bauhinia blakeana (Kachnar) of height 120-150 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge

Providing and stacking of Plumeria rubra of height 120-150 cm. with 3-4 branches and thick stem in big size HDPE bags as per direction of the officer-in-charge.

Providing and stacking of Largerstroemia indica of height 90-105 cm. multibranched in poly bags of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Polyalthia longifolia (Ashok) of height 150-165 cm. in earthen pots of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Pterospermum acerifolium (Kanak Champa) of height 150-165 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Tamarindus indica (Imli) of height 120-150 cm. in big polybags of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Mangifera indica (Mango-grafted ) of height 60-75 cm. in big poly bag of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Eugenia jambolana (Jamun) of height 150-165 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Phyllanthus emblica (Amla) of height 150-165 cm. in Big HDPE Bag as per direction of the officer-in-charge.

Providing and stacking of Foxtail palm of ht. 240-270 cm bottom girth 35- 40 cm well developed in big size HDPE bags as per direction of the officer-in-charge.

Providing and stacking of Bottle palm of ht. 210-240 cm bottom girth 30-35 cm well developed in big HDPE bags.

Providing and Displaying Bamboo Buddha vally variety with umbrella shape having 120 to 135 ht. with fresh & healthy foliage well developed in 40 cm Cement pot multy branch, bushy as per direction of the officer-in-charge.

Providing and stacking of Clerodendrum inerme having ht. 25 cm to 30 cm multi branched in 20 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge.

Providing and stacking of Ficus panda of height 90-105 cm. with 10-12 branches and healthy foliage, well formed in cement pots of size 30 cm as per direction of the officer-in-charge.

Providing and Displaying Ficus Starlight with fresh, healthy and attractive foliage 45 to 60 cm spread 75 to 90 cm ht., specimen bushy ,in 35 cm Cement Pot as per direction of the officer-in-charge.

Providing and stacking of Gardenia jasminoides of height 45-60 cm. with 3-4 branches in earthen pots of size 20 cm as per direction of the officer-in-charge.

Providing and stacking of Duranta Golden, having ht.15 to 20 cm bushty shape with fresh and healthy leaves in 15 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge..

Providing and stacking of Hamelia patens of height 30-45 cm. with 3-4 branches in poly bags of size 20 cm as per direction of the officer-in-charge.

Providing and stacking of Hibiscus rosasinensis of height 45-60 cm. with 3-4 branches in earthen pots of size 20 cm as per direction of the officer-in-charge.

Providing and displaying of Raphis palm having ht. 75 cm to 90 cm with 12 to 15 equal suckers, well developed, full of fresh & healthy leaves from bottom to top in 25 cm size Earthen pot/Plastic pot & as per direction of the officer-in-charge.

Providing and stacking of Tecoma gaudichaudi of height 45-60 cm. in earthen pots of size 20 cm as per direction of the officer-in-charge.

Providing and stacking of Tabernaemontana coronaria (chandni variegated) of height 45-60 cm. with 3-4 branches earthen pots of size 20 cm as per direction of the officer-in-charge.

Providing and stacking of plant Canna dwarf of height 25 to 30 cm., 2 to 3 suckers in earthen pots of size 20 cm Earthen Pot/Plastic Pot and as per direction of the officer-in-charge.

Providing and Displaying Standard Rose (H.T. variety) 3 to 4 healthy branch 90 cm and above ht. well developed with one and above flowers in 25 cm Earthen Pot, as per direction of the officer-in-charge.

Providing and stacking of Alternanthera species of height 15 cm to 20 cm, full of branches and foliage in 15 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge.

Providing and stacking of Chlorophytum (Green), full of leafy suckers in 15 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge.

Providing and stacking of Jatropha multifida (red colour) of height 45-60 cm. with 2-3 branches in earthen pots of size 20 cm as per direction of the officer-in-charge.

Providing and stacking of Asparagus sprengeri of height 30 cm to 45 cm, full of leafy branches in 15 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge..

Providing and stacking of Syngonium (Butterfly) variegated with 2-3 suckers healthy foliage in Earthen Pot/Plastic Pot of size 20 cm. as per direction of the officer-in-charge.

Providing and stacking of Tradescantia, full of leaves in Earthen Pot/Plastic Pot of size 15 cm. as per direction of the officer-in-charge.

FURNITURE

2 SEATER DESK BENCH - Table top (Desk)- 1100mm(l)x 400m(d)x750mm(h) shall be made up of 18 mm thick Prelaimated particle Board with 2mm thick in jection molded virginpolypropylene copolymer. The Seat(Bench)and backrest shall be of 18 mm thick Prelaimated particle Board with 2 mm thick PVC edge banding. Front Modesty Panel(250mmD)18 mm thick Prelaimated particle Board with 2 mm thick PVC edge banding. Frame structure: All side metal frames and cross connectors are made from 25.4mmx 25.4 mm x1.2 mm thick CRCA tubes , base which are welded to the desk and seat support. Stiffeners that are provided between the 2 vertical frames at base and back of seat are made from 25.4 x25.4 x1.2 mm .The back support are provided at the rear back are made of 50.8x25.4x1.2mm rectangularCRCA tubes. The storage shelves are to be made from 0.8 mm thkCRCA sheet fixed below desk top panel.. Hooks are to be provided on vertical side frames on both side of the desk made of 2 mm MS sheets for hanging bags and bottles

2 SEATER DESK BENCH 3 SEATER DESK BENCH-32 converted in two seater -Table top (Desk)- 1100mm(l)x 400m(d)x750mm(h) shall be made up of 18 mm thick Prelaimated particle Board with 2mm thick in jection molded virginpolypropylene copolymer. The Seat(Bench)and backrest shall be of 18 mm thick Prelaimated particle Board with 2 mm thick PVC edge banding. Front Modesty Panel(250mmD)18 mm thick Prelaimated particle Board with 2 mm thick PVC edge banding. Frame structure: All side metal frames and cross connectors are made from 25.4mmx 25.4 mm x1.2 mm thick CRCA tubes , base which are welded to the desk and seat support. Stiffeners that are provided between the 2 vertical frames at base and back of seat are made from 25.4 x25.4 x1.2 mm .The back support are provided at the rear back are made of 50.8x25.4x1.2mm rectangularCRCA tubes. The storage shelves are to be made from 0.8 mm thkCRCA sheet fixed below desk top panel.. Hooks are to be provided on vertical side frames on both side of the desk made of 2 mm MS sheets for hanging bags and bottles

CLASSROOM DESK Providing and suppling of student desk SIZE:-1150Lx850Dx750H Two Seater Desk Student Desk comprises of both Ply and Powder Coating made out of 25mm Thick Ply Top with Side Panel and other in 18mm Thick Ply.The working and non-working edges shall be finished with machine pressed PV Edgebanding. Student Desk with Two Seater and Three Seater Desk in modern Design made from High Quality wood materials with Long Life and Highly Durable.

CLASSROOM CHAIR The cushioned seat assembly consists of seat base moulded in glass-filled poly-amide,moulded polyurethane foam & upholstered with high stretch knitted polyester fabric.The cushioned back assembly consists of back inner moulded in polypropylene in - situ moulded with polyurethane foam & upholstered with high stretch knitted polyester fabric.Back size:45.5 cm (W) x 53.0 cm (H).Seat size:48.5 cm. (W) x 47.0 cm (D).The HR polyurethane foam used in seat and back cushion is moulded in density 45 ± 2 kg/m³,and hardness load 16 ± 2 kgf as per IS:7888 for 25% compression.The seat and back are firmly connected to the base frame and are cantilevered in such a way that it gives a multi- dimensional movement possibility just with a simple lean on the sides or back,without need for complex manual adjustments.The cantilevered seat offers impact cushioning while sitting and synchronises with the back movement during posture changes.The "S"shaped spines moulded in high strength glass-filled poly-amide and the spine connector moulded in glass-filled poly-amide form the back-spine structure involved in multi-dimensional recline motion.The variable tilt angle recline motion can be adjusted with 3 position tilt limit feature which is inbuilt in seat base and the tension is user weight dependent.The assembly consists of armrest housing sliding over the armrest structure,both moulded in glass-filled poly-amide.The height adjustment feature is button operated having adjustment of 6.6 ± 0.5 cm.The armrest top is made up of integral skin PU moulded over plastic inner moulded in glass- filled poly-amide.The seating height can be adjusted with a pneumatic gas-lift having an adjustment stroke of 9.2 ± 0.3 cm.The pedestal is injection moulded in glass-filled poly-amide and fitted with 5 nos.twin wheel castors.The pedestal is 66.0 ± 0.5 cm.pitch centre diameter and 76.0 ± 1.0 cm.with castors.5 nos. twin wheel castors are injection moulded in poly-amide having 5.0 ± 0.1 cm wheel diameter and assembled to the pedestal. The bidder should either be an OEM or authorized dealer of the OEM. The authorized dealer of OEM should have dealership for the last 5 financial years.PF & ESI registration is mandatory for both OEM & Reseller. Manufacturer should have BIFMA Member Certificate, India Design Mark Certificate, Green Guard , Green Pro , GRIHA, Indoor Advantage certification along with products certifications like; AIOTA, BIFMA level 3 conforms to ANSI/BIFMA e3- 2014e Furniture Sustainability Standard issued by BIFMA. Other certificates ISO 9001:2015, ISO 14001:2015, ISO 50001:2018, ISO 45001:2018, ISO 13485 : 2016 (TUV) is mandatory. Manufacturer should have Green Guard, BIFMA , Green Pro, GRIHA,IAQ Certification for few of its products. All the ISO certificates should be obtained from NABCB (central Govt) accredited organization otherwise certificates will not be accepted. Sample and factory visit is mandatory to inspect as per the requisite. Supplier should

TABLE SINGLE SIDE-11 SEATER The scope of laboratory furniture shall consist of supply of raw material, fabrication, assembling, preparation of design, drawings, supply and erection. Work shall be executed in a well coordinated and professional manner. The complete M.S. material of cabinet to be pre – treated (degreased, Zinc Phosphated) and epoxy powder coated for better corrosion resistance. The thickness of powder coat to be 70 to 80 microns, which passes the Salt Spray test for 1000 hours and having the Scratch Hardness of 3Kgs 18± 2mm thick Jet Black granite top with moulding of approved design on the front edge. Groove at the bottom of granite after leaving 25 mm from the front to avoid liquid spillage. The pedestal frame shall be made of high quality ERW steel tubes of size 30 mm x 30 mm x 1.5 mm. Pedestal shall be finished in approved color with epoxy polyester powder coating. Leveling screws will be provided at the bottom of the tubular legs and the same shall be covered by means of black plastic spats for good aesthetics. CRCA MS sheet/ PVC Trunking with inbuilt division for laying Electrical/Data & voice cabling facilities shall be given: 100mm x 50mm thick. 1.5mm to 2.5 sq mm. wires shall be used. The termination with end connector shall be at the end of the Truncking. (Necessary connections can be provided). NLT 50 micron thickness Epoxy powder coating (approved colors) shall be done on all modules and on all pedestals. The EIGHT (8) tank pre treatment shall be given before the powder coating. One piece moulded non reactive PP sinks shall be given in the furniture.Option of supplying on demand S.S

TABLE DUEL SIDE-14 SEATER The scope of laboratory furniture shall consist of supply of raw material, fabrication, assembling, preparation of design, drawings, supply and erection. Work shall be executed in a well coordinated and professional manner. The complete M.S. material of cabinet to be pre – treated (degreased, Zinc Phosphated) and epoxy powder coated for better corrosion resistance. The thickness of powder coat to be 70 to 80 microns, which passes the Salt Spray test for 1000 hours and having the Scratch Hardness of 3Kgs 18± 2mm thick Jet Black granite top with moulding of approved design on the front edge. Groove at the bottom of granite after leaving 25 mm from the front to avoid liquid spillage.

TABLE DUEL SIDE-16 SEATER The scope of laboratory furniture shall consist of supply of raw material, fabrication, assembling, preparation of design, drawings, supply and erection. Work shall be executed in a well coordinated and professional manner. The complete M.S. material of cabinet to be pre – treated (degreased, Zinc Phosphated) and epoxy powder coated for better corrosion resistance. The thickness of powder coat to be 70 to 80 microns, which passes the Salt Spray test for 1000 hours and having the Scratch Hardness of 3Kgs 18± 2mm thick Jet Black granite top with moulding of approved design on the front edge. Groove at the bottom of granite after leaving 25 mm from the front to avoid liquid spillage.

The scope of laboratory furniture shall consist of supply of raw material, fabrication, assembling, preparation of design, drawings, supply and erection. Work shall be executed in a well coordinated and professional manner. The complete M.S. material of cabinet to be pre – treated (degreased, Zinc Phosphated) and epoxy powder coated for better corrosion resistance. The thickness of powder coat to be 70 to 80 microns, which passes the Salt Spray test for 1000 hours and having the Scratch Hardness of 3Kgs 18± 2mm thick Jet Black granite top with moulding of approved design on the front edge. Groove at the bottom of granite after leaving 25 mm from the front to avoid liquid spillage. The pedestal frame shall be made of high quality ERW steel tubes of size 30 mm x 30 mm x 1.5 mm. Pedestal shall be finished in approved color with epoxy polyester powder coating. Leveling screws will be provided at the bottom of the tubular legs and the same shall be covered by means of black plastic spats for good aesthetics. CRCA MS sheet/ PVC Trunking with inbuilt division for laying Electrical/Data & voice cabling facilities shall be given: 100mm x 50mm thick. 1.5mm to 2.5 sq mm. wires shall be used. The termination with end connector shall be at the end of the Truncking. (Necessary connections can be provided). NLT 50 micron thickness Epoxy powder coating (approved colors) shall be done on all modules and on all pedestals. The EIGHT (8) tank pre treatment shall be given before the powder coating. One piece moulded non reactive PP sinks shall be given in the furniture.Option of supplying on demand S.S 304 or S.S316 or Ceramic sink shall be given and will be quoted separately. All fittings shall bear a guaranteed life of minimum one year.

MAIN CHAIR Overall Dimensions –(W) 660mm X (D) 490mm X (H) 1215mm Features – High back mesh chair with fabric covered seat, deep cusioned with 12mm thick BWP plywood base frame & ergonmically designed back and seat conforming to body contours for proper alignment, posture and all day comfort with 360° revolving mechanism as depicted above. The one-piece armrests should be injection moulded with height adjustment of 75mm. The backrest should be made up of upholstered using double-layer spacer mesh fabric and the backrest is made of one- piece injection moulded frame. The back rest shall have a tilt mechanism. The headrest shall be made of injection moulded frame with fabric covered deep cushion, and the headrest shall be height adjustable and also provision for removal of the headrest. The height adjustment shall be for 50mm.The pedestal of the chair shall be chrome plated with 5 legs with dual wheel castors with cover for the wheels. The chair shall have a pneumatic height adjustment provision of 100mm.

VISITOR CHAIR Overall Dimensions –(W) 640mm X (D) 670mm X (H) 1100mm Features – High back mesh chair with fabric covered seat, deep cusioned with 12mm thick BWP plywood base frame & ergonmically designed back and seat conforming to body contours for proper alignment, posture and all day comfort with 360° revolving mechanism as depicted above. The one-piece armrests should be injection moulded with height adjustment of 75mm. The backrest should be made up of upholstered using double-layer spacer mesh fabric and the backrest is made of one- piece injection moulded frame. The back rest shall have a tilt mechanism. The headrest shall be made of injection moulded frame with fabric covered deep cushion, and the headrest shall be height adjustable and also provision for removal of the headrest. The height adjustment shall be for 50mm.The pedestal of the chair shall be chrome plated with 5 legs with dual wheel castors with cover for the wheels. The chair shall have a pneumatic height adjustment provision of 100mm.

TABLE DUEL SIDE-12 SEATERThe scope of laboratory furniture shall consist of supply of raw material, fabrication, assembling, preparation of design, drawings, supply and erection. Work shall be executed in a well coordinated and professional manner. The complete M.S. material of cabinet to be pre – treated (degreased, Zinc Phosphated) and epoxy powder coated for better corrosion resistance. The thickness of powder coat to be 70 to 80 microns, which passes the Salt Spray test for 1000 hours and having the Scratch Hardness of 3Kgs 18± 2mm thick Jet Black granite top with moulding of approved design on the front edge. Groove at the bottom of granite after leaving 25 mm from the front to avoid liquid spillage.

BASIC LAB TABLE SINGLE SIDE-8 SEATER The scope of laboratory furniture shall consist of supply of raw material, fabrication, assembling, preparation of design, drawings, supply and erection. Work shall be executed in a well coordinated and professional manner. The complete M.S. material of cabinet to be pre – treated (degreased, Zinc Phosphated) and epoxy powder coated for better corrosion resistance. The thickness of powder coat to be 70 to 80 microns, whic passes the Salt Spray test for 1000 hours and having the Scratch Hardness of 3Kgs 18± 2mm thick Jet Black granite top with moulding of approved design on the front edge. Groove at the bottom of granite after leaving 25 mm from the front to avoid liquid spillage. The pedestal frame shall be made of high quality ERW steel tubes of size 30 mm x 30 mm x 1.5 mm. Pedestal shall be finished in approved color with epoxy polyester powder coating. Leveling screws will be provided at the bottom of the tubular legs and the same shall be covered by means of black plastic spats for good aesthetics. CRCA MS sheet/ PVC Trunking with inbuilt division for laying Electrical/Data & voice cabling facilities shal be given: 100mm x 50mm thick. 1.5mm to 2.5 sq mm. wires shall be used. The termination with end connector shall be at the end of the Truncking. (Necessary connections can be provided). NLT 50 micron thickness Epoxy powder coating (approved colors) shall be done on all modules and on all pedestals. The EIGHT (8) tank pre treatment shall be given before the powder coating. One piece moulded non reactive PP sinks shall be given in the furniture.Option of supplying on demand S.S 304 or S.S316 or Ceramic sink shall be given and will be quoted separately. All fittings shall bear a guaranteed life of minimum one year. 1) Hinges:- Corrosion resistant CED Coated hinges shall be supplied with all the modules. 2) Handles:-All handles shall be of SS 304/ Alu concealed Handles Handless may be in two tones or single tone. 3) Brand of Locks:- Godrej/Ebco. 4) Brands for Electrical Fittings:- Northwest or equivalent make 230V, 6/15Amp, with 3 pin socket in eac 1.5 mtr and piano switches, or Industrial switches & sockets shall be provided. 5) Utility : 3 way/ 1 way taps:- Taps will be epoxy powder coated , with DIN 12920 cooler coding, or S.S taps as per the requirement. Laboratory Workbench provided as per layout in combination of 1800 x 750 x 850 (with storage cabinet) LAB Workstation- Supply of laboratory workbench 1800 x 750 x 850 (with storage cabinet). All Pedestal

PRINCIPAL ROOM MAIN DESK PROVIDING AND SUPPLING OF PRINCIPLE MAIN DESK, STRUCTURE OF TABLE TOP L-SHAPE . PRIMARY WORK SURFACE OVER ALL SIZE IS 2400MM(L)X 1000MM(D)X 770MM(H) 50MM THICK TABLE TOP MADE OF MDF BOARD WITH NATURAL VENNER WORK SURFACE WITH CHERRY FINISH VENEER SAME MATCHING VENEER EDGE BANDING MADE OF SAME DARK CHERRY P.U. POLISH.MODESTY IS DESIGNED WITH LEATHER PATCH.SIDE PANNEL MADE OF 40MM THICK . * PROVISION OF SIDE UNIT OF SIZE IS 900MM(L)X 595MM(D)X 770MM(H) ,CONSTRUCTION OF SIDE UNIT TOP MADE OF 50MM THICK, 1 FIXED SHELVE WITH 1 SLIDDING SHUTTER. * ALL THE MDF BORAD ARE IS-14587-1998 WITH CONFIRM TO DIN 68861.ISO 9001- 2015 QUALITY CERTIFICATION CONFIRMING TO ASTM D 4499 STANDARDS FOR VISCOSITY AND THERMAL STABILITY . * THE SELLER / COMPANY SHOULD BE ISO 9001:2015, ISO 50001:2018, ISO 14001:2015, ISO 45001:2018 CERTIFICATES OF THE MANUFACTURER CERTIFIED BY NATIONAL ACCREDITATION BOARD OF CERTIFYING BODIES, IGBC, SEDEX, GREEN PRO, AIOTA, INDIAN DESIGN MARK , FSC CERTIFICATE. THE BIDDER SHOULD BE A MEMBER OF BIFMA AND AT LEAST TWO PRODUCTS OF THE OEM SHOULD BE CERTIFIED AS BIFMA COMPLIANT AND AN OFFICIAL PRODUCT OFFICIAL LINK/SCREENSHOT OF THE PRODUCT LISTING MUST BE PROVIDED FROM WWW.BIFMA.ORG".

HIGH BACK REVOLVING CHAIR Providing and fixing High Back chairs made of 1" ERW pipe of 16 gauge seat and back is made of 12 mm hot press single ply and provided with 40/50 & 23 density 12 mm pure foam (Feather foam make) and covered with premium quality of leather/fabric. The chair with duo colour fabric combinations as per EIC / Architect. The chair shall be provided with 120mm BIFMA Passed gas lift and conventional tilt mechanism with one lever control for lock and seat height adjustment. Plate thickness shall 2.5 mm and angle is 3~18 (BIFM Passed) with poly urethane one pipe handle and nylon base having 1359 kg weight capacity as per BIFM standard.all the metal parts of the chair are pre treated prior to powder coating/chrome.size 675X675X1165mm . seat ht: 440/540mm

Supplying and placing in position of 360 degree revloving high back chair as per Image. The Genius office chair of size:- (W)700mm X (D)540mm X (H)1265mm with Maximum Seating Height 600 mm and Minimum Seat Height 515 mm. The contemporary chair comprises of luxurious contoured cushions with dual padding and a central indent that provides lower back support for proper posture and comfort. The central panel in the backrest is neatly stitched with a soft seat waterfall cushion finished in the same black leatherette. The Chair nestles on a matte silver painted nylon vaulted base with nylon castors. the shiny armrests come thickly padded for comfort. The product shall be from ISO 9001:2015,ISO 50001:2011, ISO 14001, OHSAS 18000 , BIFMA, FSC, AIOTA, SEDEX & Greenguard Certified company and complete as per the approved sample and as per the direction of Engineer-In-Charge.

PROVIDING AND SUPPLING OF BACK UNIT BACK UNIT STORAGE MATERIAL : PRELAMINATED PARTICLE BOARD/VENEER - MDF/STEAM BEECH VENEER , BACK UNIT SIZE : 1600 MM (L)X 400 MM (D)X 770 MM (H). COLOUR : RED - DARK CHERRY & FINISH : GLOSSY . * PROVIDING & SUPPLING PLACING POSITION OF MODULAR BACK UNIT TOP SHALL BE MADE FROM 25 MM THICK PRELAMINATED PARTICLE BOARD/VENEER - MDF/STEAM BEECH VENEER OF GRADE II TYPE III OF IS 12823/LATEST & CONFIRM TO DIN 68861.ISO 9001- 2015. * WHILE REST OF THE SIDES AS WELL AS SHELVES AND SHUTTER TO BE MADE UP OF 18 MM THICK PRELAMINATED PARTICLE BOARD/VENEER - MDF/STEAM BEECH VENEER P.U. POLISH. ALL EDGES TO BE PROVIDED WITH SAME MATCHING VENEER EDGE BANDING FIXED WITH THE HOT MELT GLUE. * STORAGE UNIT WITH 4 SHUTTERS CONSTRUCTION IS 2 OPENABLE DOORS WITH 1 FIXED SHELVE + 2 OPENABLE DOORS WITH 1 FIXED SHELVE , IN PROVIDED WITH 2 UNIVERSAL CAM LOCK FOR SECURITY AND HANDLES ARE PROVIDED FOR EASY OF OPENING. OVER ALL HEIGHT OF PRODUCT IS @ 770 MM . * EACH SHUTTER SHOULD BE FIXED WITH REQUIRED NUMBERS HINGES, SS TOWER BOLT OF 100 X 10, DOUBLE STRIP MAGNETIC CATCHER AND DRAWERS SHALL HAVE 100 MM SIZE SS FANCY HANDLES (ONE ON EACH DRAWER) WITH NECESSARY HARDWARE/ FITTING/ HINGES ETC. OF APPROVED QUALITY(MAKE: EBCO).FOR INSTALLATION OF SIDE UNIT WOODEN DOWELS AND MINIFIX TO USE FOR ADDITIONAL SUPPORT. * ALL THE MDF BORAD ARE IS-14587-1998 WITH CONFIRM TO DIN 68861.ISO 9001- 2015 QUALITY CERTIFICATION CONFIRMING TO ASTM D 4499 STANDARDS FOR VISCOSITY AND THERMAL STABILITY . * THE SELLER / COMPANY SHOULD BE ISO 9001:2015, ISO 50001:2018, ISO 14001:2015, ISO 45001:2018 CERTIFICATES OF THEMANUFACTURER CERTIFIED BY NATIONAL ACCREDITATION BOARD OF CERTIFYING BODIES, IGBC, SEDEX, GREENGUARD COMPLIANCE, GREEN PRO, AIOTA, INDIAN DESIGN

Providing and Placing in position of Sofa Set (3+1+1) as per image. The contemporary designed sofa of Size : (L)194.0cm X (D)88.0cm X (H)95.0cm and Single Seater sofa of Size : (L)96.5cm X (D)88.0cm X (H)95.0cm, seat height 46.0cm, seat depth 51.0cm and back height 55.0cm, should be upholstered in premium leatherette, this sofa is sleek and comfortable. The wooden frame is finished in a rich brown polish with split panel seating. The back and seat have medium to firm cushioning for better posture. The Sofa stands on moulded pvc legs beautiful accents that are slightly curved on the front face of the sofa. Each curve defines a seating space which provides for people to be seated comfortably. Finished in a luxurious Leatherette, the sofa exudes a certain class. Seat of Sofa is layered with silicon fibre filling over high density foam. The seat cushion is made of multi layered foam of density 32(+/-2kg /m3). The seating cushions have 2.75 & 1.75 inches of elastic webbing. The thread used is nylon bonded to provide lasting stitch strength. Complete as per direction of Engineer -in –Charge.

Supplying and placing in position of centre table as per photograph. Size (L)1130mm X (W)630mm X (H)410mm,The centre table made of solid wood (steam beech) in pu matt polish.The plain glass placed the top of the table in 8mm thk. The turned wooden legs are sleek and sturdy providing the table with its support. The wood work below the glass provides the glass with a focal point and some support. Add volumes of style to yourliving room with the centre table. Material & subtype: Solid Wood -Beech Wood( spc:steam beach), Colour & Colour Family:Brown - Dark Oak,Shape:Rectangular Legs/Base:Solid Wood, Finish:Glossy,Style:Contemporary.

Supplying, and placing in position of side table Dimension(L)680mm X (W)530mm.The side table made of solid wood (steam beech) in pu matt polish.The plain glass placed the top of the table in 8mm thk. The glass table top is made with strong glass and is inlaid onto the solid wood frame. The designer wooden legs are turned for a sleeker look. The framed edges slope inwards to the table top with defined edges. Material & Subtype:Solid Wood - Beech Wood ( spc:steam beach), Colour & Colour Family:Brown - Dark Oak, Legs:Solid Wood, Finish:Glossy, Style:Contemporary.

PROVIDING AND SUPPLING OF L SHAPE TABLE STRUCTURE OF TABLE TOP L-SHAPE . PRIMARY WORK SURFACE OVER ALL SIZE IS 1800MM(L)X 900MM(D)X 750MM(H) 50MM THICK TABLE TOP MADE OF MDF BOARD WITH NATURAL VENNER WORK SURFACE WITH CHERRY FINISH VENEER SAME MATCHING EDGE BANDING MADE OF SAME DARK CHERRY P.U. POLISH.MODESTY IS DESIGNED WITH LEATHER PATCH.SIDE PANNEL MADE OF 40MM THICK . * PROVISION OF SIDE UNIT OF SIZE IS 900MM(L)X 595MM(D)X 770MM(H) ,CONSTRUCTION OF SIDE UNIT STORAGE 1 FIXED SHELVES WITH 1 SLIDING SHUTTER . * ALL THE MDF BORAD ARE IS-14587-1998 WITH CONFIRM TO DIN 68861.ISO 9001- 2015 QUALITY CERTIFICATION CONFIRMING TO ASTM D 4499 STANDARDS FOR VISCOSITY AND THERMAL STABILITY . * THE SELLER / COMPANY SHOULD BE ISO 9001:2015, ISO 50001:2018, ISO 14001:2015, ISO 45001:2018 CERTIFICATES OF THE MANUFACTURER CERTIFIED BY NATIONAL ACCREDITATION BOARD OF CERTIFYING BODIES, IGBC, SEDEX, GREEN PRO, AIOTA, INDIAN DESIGN MARK , FSC CERTIFICATE. THE BIDDER SHOULD BE A MEMBER OF BIFMA AND AT LEAST TWO PRODUCTS OF THE OEM SHOULD BE CERTIFIED AS BIFMA COMPLIANT AND AN OFFICIAL PRODUCT OFFICIAL LINK/SCREENSHOT OF THE PRODUCT LISTING MUST BE PROVIDED FROM WWW.BIFMA.ORG".

Supplying, and placing in position of 2str sofa as per Image . Sofa Size :- (L) 1410mm X (D) 890mm X (H) 870mm. classic Contemporary design and slender curves, Berry is the finest piece of furniture we have made. The Sofaof stands Firm on solid PVC legs with thick armrests that are slightly curved on the front face of the sofa. Each curve defines a seating space which provides for people to be seated comfortably. Finished in a Brown Nappa Aire Leather, the sofa makes a fantastic first impression. The Cushioning is molded such that it flows along the partition for a clean unified look. The seat cushion is made of multi layered foam of density 40kg/m3. The seating cushion have 2.75 & 1.75 inches of elastic webbing. The thread used is nylon bonded to provide lasting stitch strength . The backrest has a foam of 28kg/m3 with polyster polyfill outer layer of 200 gsm. The polyster polyfill keeps the upholstery wrinke free & soft .The product should be from company which has BIFMA membership & Greenguard/ FSC certification . Complete as per image, and specification under the guidance of Engineer in charge.

Supplying and placing in position of Table for manager as per photograph. Modular table size 1200mm (L) X 600mm (W) X 750mm (H), Table top shall be made of 25mm thick pre-laminated particle board of approved shade. Table Top working edges shall be provided with matching machine pressed 2mm thick PVC edging using with special hot melt glue at hot temperature. Table top supported on side panles and modesty panel. Side and Modesty panel shall be made out of 18mm thick pre-laminated particle board laminated on both sides as approved shade. The working or nonworking edges shall be provided with matching machine pressed 2mm thick PVC edging using with special hot melt glue at hot temperature. Provision of 400L x 450W x 725Ht Fixed Pedestal of 2 Drawer + 1 Filling unit, made of 18mm thk Prelaminated Particle Board with PVC edge banding. All drawers shall have a central lock mechanism. PVC keyboard tray and MS powder coated CPU Trolley. The product shall be from ISO 9001:2015,ISO 50001:2011, ISO 14001, OHSAS 18000 , BIFMA, AIOTA & Greenguard Certified company and complete as per the approved sample and as per the direction of Engineer-In-Charge.

Providing, supplying and placing in position of ISO 9001:2015,ISO 14001:2015, OHSAS 45001:2018/18001:2007, BIFMA registered, Griha certified, IGBC Gold certified and Green Guard Certified manufacturer "L- SHAPE WORKSTATION" with following specifications: Size: 1500/1350W X 600/600D X 750HT TABLE TOP WITH 350MM HT SCREEN Mobile Pedestal 2D1F: 400W X 450D X 600HT Specifications: Table top: Made of 25mm thick prelaminated particle board of approved shade. All the edges of workstation surface shall be provided with machine pressed 2mm thick imported PVC lipping glued with hotmelt Eva glue free from any VOC. Main Screen: 18mm thick Fabric magnetic screen on powder coated studs. Return Screen: 18mm thick Fabric magnetic screen on powder coated studs. Under Structure Support: Table top is supported on MS Powder coated Collaborate Legs constructed by using Specially tooled & specifically designed Diamond shape 50x25x1.6thk ERW Tube – 16g, strong Leg bush & levellers made of Acrylonitrile butadiene styrene (ABS), a very tough material. Legs are connected using MS cross beams made of 40 x 20 16 gauge rectangular tube. Model: FEATHERLITE PERFORM L-SHAPE WORKSTATION or approved equivalent model of Godrej/Wipro/Durian/Hoff

Size: 1350L x 600W x 750/1050Ht 65 mm thk Sliding Tile base partition 1050Ht in main span. Single metal wire raceway cover at skirting level in main span partition. Soft board and White board in front partition above table top. Prelaminated Particle board tile in Partition on Passage side. 25mm thk tabletop made up of Prelam Particle Board with PVC Edge banding. Tabletop supported with 18mm thk prelam perticle board size panel.

Medium Back Chair Made Of Good Quality Products. Seat & Back Plywood Made Of 13.5mm Hot Pressed Supported . Understructure Base Of Chair Metal Structure Fixed Type . Upholstery Structure Moulded With Prime Quality Leatherite . Understructure Base Fixed Type CRCA 40 x 20 mm Metal Pipe 2mm Thick Duly Powder Coated . Machanism & PHA ( Gas Lift ) NA . Seat & Back Are Firmly Connected To The Metal Frame . Chair Max Height 990 & min Depth 720mm . 500W x 480D Base Seat 100mm Thick Moulded With PU Foam , D - 32 kg/m3 , H - 20 & 530W x 630H Back Seat 100mm Thick Moulded With PU Foam , D - 32 kg/m3 , H - 20 . Back , Seat Shell & L - Patta NA Beading Finish With Chrome Plated . 510/600 Arm Rest Fitted To The Seat With Armrest Connecting Brackets . Arm Rest Height From Seat 190mm . Arm Rest Soft Cushioning On Plastic Handle Over Chrome Base . Height From Seat To Ground 470mm .

Providing And Supplying Modern Design Reception Desk A Combination Of Steel,Glass And Wood Make The Products Utile And A Delight.Timeless Design That Elevates Your Office Space Structure Of Spacious Reception Desk,Tabletop Offers You A Generous Look For Work Surface Use Premium Quality Materials Over All Size Is 1500 Mm(L)X 600 Mm(D)X 750 Mm(H) Which Give More Surface Area For Work ,Table Top Made Of 25mm Thick Also Table Top Based On Side Panel's Made 18mm Thick Prelaminated Particle Board Of Grade Ii Type Iii Of Is 12823/Latest.Combination Construction Of Reception Desk Above Table 18 Mm Thick Counter Top With Glass Height From Table Top @ 350mm,10 Mm Thick Clear Glass Diamond Cut Finish On Edes Based On Stainles Steel Stud Grade 304,Overall Reception Desk Height Is @ 1100mm With Glass,On Table Top Pvc Groment Hole For Wire Management & Top Made 25 Mm Thick Prelam Particle Board Work Surface With The Exposed Edges Shall Be Finished With 2mm Thick Pvc Edge Binding Tape Of Matching Colour And Shade Fixed With Hot Melt Glue

RECEPTION CHAIR High Back Chair Made Of Good Quality Products. Seat Plywood Made of 12mm Hot Pressed. Upholstery PVC Structure Molded with Prime Quality High Stretch Fabric Mesh. PHA ( GasLift ) 85mm (TDC 152mm & BDC 67) . Seat & Back Are Firmly Connected To The Base Frame Mechanism. Mechanism Provided Upright Position Locking. Tilt Adjustment Can Be Operated In Seating Position. Chair Max Height 1250 & min Height 1165. 470x460 Base Seat 70mm Thick Molded with PU Foam D - 45kg/m3 & 500x780 Back Seat PP Structure Molded With Fabric Mesh. Headrest Adjustable Type PU Foam With PP Cover At Back. 160x415/590 Arm Rest Fixed Type PP. Height From Seat To Ground 460mm . Understructure Used Chrome Plated Steel Base. Casters Made Of Moulded Black Nylon Metal Bolt Inserted & Fitted With 5 Nos . Twin Wheel Casters 50mm Dia . Pedestral Pitch Centre Dia 665mm Without Casters.

3 SEATER SOFA Supplying, and placing in position of 3str sofa as per image.The Sofa of Size :- (L)1650mm X (D)750mm X (H)710mm. Leatherette upholstery adds class to the soft cushioned backrest and seating.Legs: Stainless Steel , Finish: Matte, Style: Modern.The seat cushion is made of multi layered foam of density 40kg/m3. The seating cushion have 2.75 & 1.75 inches of elastic webbing. The thread used is nylon bonded to provide lasting stitch strength . The backrest has a foam of 28kg/m3 with polyster polyfill outer layer of 200 gsm. The polyster polyfill keeps the upholstery wrinke free & soft.Frame Structure Material and size (±1 mm) any other wood of minimum 25 mm thickness.Seat Cusion Material foam.Type of Spring in the Base / Seating No Spring in the Base.Sofa Height (Without Back Cushion) ±5 (mm) 600 millimeter. Sofa Height (With Back Cushion) ±5 mm 700 millimeter. Arm Width ±5 (mm) 150 millimeter. Arm Height ±5 (mm) 400 millimeter. Seat Height (With Seat Cushion) ±5 (mm) 400 millimeter. Sofa Leg Height ±2(mm) 75 millimeter.Sofa Leg Width / Diameter ±2 (mm) 25 millimeter.Complete as per image, and specification under the guidance of Engineer in charge.

STAFF ROOM TABLE: Overall Size 2400W x 1200D x 750H Understructure - Metal powder coated "C" shape Leg of 50x50x1.6 mm thk with Connector in side 25 mm thk PLPLB panel .Provision of 8 Module Flip up box(size; 300Lx120D) with Metal wire tray and Vertical riser for wire management. 0.8 mm thk Metal perforated Modesty 450 ht.

Providing and fixing of Lounge Chair with the following specifications. Base : Base shall be supported with wooden legs with polish as shown in the image and approval of the architect. Base/leg leveller to be added as per the approval of architect. Seat with arm rest & Back: Seat & back shall be inhigh density Bonded Polyurethane foam wrapped & upholstered in approved fabric with wooden frame work

Supply, Installation and placement of Flexi High Back auditorium chair with PU armtop certified with ISO 9001: 2015, ISO 50001: 2018, ISO 45001: 2018, ISO 14001:2015 (all ISO must be from NABCB accredited agency), BIFMA (membership),AIOTA, Green guard by UL , indoor air quality certified manufacturer. Overall Dimensions: CENTRE TO CENTRE (C): 58.7 cm. DEPTH (Di): 50.5 cm. WIDTH (W1) : 67.5 cm. DEPTH (D2) : 63.0 cm. WIDTH (W2) : 50.7 cm. DEPTH (D3): 83.6cm. DEPTH (D4) : 97.6cm. SEAT HEIGHT (SH): 45.5 cm. HEIGHT (H) : 107.3cm.(Allowable Tolerance in dimension @ +/- 5 %) BACKREST ASSEMBLY: The back assembly has a flexi back mechanism. It is made of polyurethane foam moulded with M.S. tubular frame insert, upholstered with fabric and has a plastic back cover. The insert is a tubular frame made of 01.9 ±0.02cm x 0.16 ±0.013cm thk M.S.E.R.VV round tube with flexible support straps running across the length and width of the frame. Approx. Back Size : High Back- 45.5cm (W) x 82.4cm (H).HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam is moulded with density = 45 +/-3 kg/m3. SIDE PANEL / AISLE PANEL: The chair rests on the ground on two side panel frames fabricated from 0.12 ±0.020cm thk CR steel sheet which is cladded with fabric upholstery. The side panel frame is grouted to the floor using 2 nos. of anchors for each panel through 0.3 ± 0.05cm thk HR steel base plate. PU ARMREST (FOR MARS HB/MB069XXPU FIXED ARM): The armrest is made up of integral skin Polyurethane Foam with 65 +/- 10 Shore 'A' Hardness and reinforced with wooden insert. The armrest is snap fitted with side panel. POWDER COATING: Steel components are epoxy polyester powder coated (DFT 40- 60 microns).FLOORING PRE - REQUISITE : The auditorium chair is designed to get mounted/grouted on floors with flooring suitable specification as per direction of engineer in charge.

Providing and Placing in position of Three Seater Sofa as per image. The contemporary designed sofa of Size : (L)209.0cm X (D)91.0cm X (H)87.0cm, seat height 44.5cm, seat depth 52.0cm, arm height 62.5cm, inner seating width 160.0cm and back height 41.0cm, should be upholstered in premium leather, this sofa is sleek and comfortable. Premium leather upholstery that is stretched out by hand onto the foam for a sumptuous seat. The sofa is a covered in a combination of leather and leatherette with all the areas you can experiece are finished in leather and non-functional areas are finished in leatherette. The puffy arms and backrest comes with a beautiful panel detail along with tufted side arms for added design. The soft foam cushions coupled with the solid wood base makes for a classy sofa set.The back and seat have medium to firm cushioning for better posture. Finished in a luxurious Leather, the sofa exudes a certain class. Seat of Sofa is layered with silicon fibre filling over high density foam. The seat cushion is made of multi layered foam of density 32(+/-2kg /m3). The seating cushions have 2.75 & 1.75 inches of elastic webbing. The thread used is nylon bonded to provide lasting stitch strength. Complete as per direction of Engineer -in –Charge.

Material & Subtype Glass - Clear Glass Table Top Material Clear Glass Leg Material Stainless Steel Finish Glossy Colour & Colour Family Clear Glass Dimension (W)400mm X (D)400mm X (H)500mm Table Top Thickness 10mm Size Compact Assembly Type Knock Down SKU KYLE/ST

PROVIDING AND SUPPLING OF MAIN DESK STRUCTURE OF TABLE TOP L-SHAPE .PRIMARY WORK SURFACE OVER ALL SIZE IS 2000MM(L)X 900MM(D)X 750MM(H) 45MM THICK TABLE TOP MADE OF PRELAMINATED PARTICLE BOARD WORK SURFACE WITH WARM WALNUT FINISH, 2MM THICK PVC EDGE BANDING MADE OF SAME MATTE FINISH. SIDE PANNEL IS MADE OF 45MM THICK .* PROVISION OF SIDE RUNNER OF SIZE IS 1800MM(L)X 500MM(D)X 660MM(H) ,(COMBINATION CONSTRUCTION- TABLE TOP BASED ON SS STUD GRADE 304 RIGHT SIDE BELOW FROM TABLE TOP SIDE RUNNER HAVE 2 DOORS STORAGE + 3 DRAWERS WITH CETNRAL LOCK FOR SECURITY AND + 1 OPEN BOX FIXED SHELVE & LEFT SIDE BELOW SS STUD 1 FIXED PEDESTAL TOP 25MM THICK SIZE IS 400MM(L)X 500MM(D)X 650MM(H).* FIXED PEDESTAL OF SIZE 495MM(L)X 750MM(D)X 755MM(H) , HAVING 1 OPENABLE DOOR WITH CENTRAL LOCK FOR SECURITY AND HANDLES ARE PROVIDED FOR EASY OF OPENING.* THREE LAYER PRELAMINATED PARTICLES BOARD(WOOD PRODUCT) OF GRADE II TYPE III OF IS 12823/LATEST , * THE SELLER / COMPANY SHOULD BE ISO 9001:2015, ISO 50001:2018, ISO 14001:2015, ISO 45001:2018 CERTIFICATES OF THE MANUFACTURER CERTIFIED BY NATIONAL ACCREDITATION BOARD OF CERTIFYING BODIES, IGBC, SEDEX, GREEN PRO, AIOTA, INDIAN DESIGN MARK , FSC CERTIFICATE. THE BIDDER SHOULD BE A MEMBER OF BIFMA AND AT LEAST TWO PRODUCTS OF THE OEM SHOULD BE CERTIFIED AS BIFMA COMPLIANT AND AN OFFICIAL PRODUCT OFFICIAL LINK/SCREENSHOT OF THE PRODUCT LISTING MUST BE PROVIDED FROM WWW.BIFMA.ORG".

Providing and Placing in position of Sofa Set (3+2 ) Seater, Three Seater sofa of Over all dimension 2110mm (W) X 935mm (D) X 890mm (H) and 1110mm (W) X 935mm (D) X 890mm (H). Seat understructure shall be made up of combination of plywood & pinewood members. Plywood shall be 12±1mm thk. [moisture resistance & termite proof as per IS:303] & pinewood shall of cross sections 22x64mm, 34x64mm & 16x35mm without having major knots & defects on the surface. Zigzag spring of dia. 3.8mm shall be mounted on the seat structure using plastic spring mounting clip. Non woven fabric shall be stapled on the seat structure frame above the spring asly. Powder coated MS support pipe shall be fitted with the wooden seat frame to give additional strength to the structure. Complete understructure shall be made by gluing, nailing & stapling. Foam: Seat shall be made of PU foam with density 28 kg/m3 with a top layer of supersoft PU foam with density 32 kg/m3. Recron sheet of 200GSM wrapped & glued above this seat top foam. Seat front bottom is glued with the PU foam with density 28 kg/m3. Upholstery: Seat upholstery shall be made in polyester fabric, having pockets to insert the seat foam. The fabric shall have a special coating which gives it a leather like feel. Backrest understructure shall be made up of combination of plywood & pinewood members. Plywood shall be 12±1mm thk. [moisture resistance & termite proof as per IS:303] & pinewood are of cross sections 16x35mm & 16x74mm without having major knots & defects on the surface. 3mm MDF shall be stapled on the front & back of the structure. The front MDF provides a firm support for the recron back cushion to rest and the back cushion provides a surface to stick the back foam. Foam: The back cushion shall made of loose polyester fibre filled in non woven bags for each seat. Backrest upholstery shall be made in polyester fabric, having pockets to insert the back cushion bags. The fabric shall have a special coating which gives it a leather like feel.Plastic legs with the M8 stud shall be fitted at the bottom surface of both the armrests and on front of the seat. Complete as per direction of Engineer -in –Charge.

SIDE TABLE Size : 450L x 450W x 450Ht Supplying and placing Side Table with Two drawer Made of 18mm thick Prelaminated Particle Board side ,top and bottom . Drawer side, bottom and back made out of prelam particle board. All exposed edges to be provided with 2.0 mm thick matching grain PVC lipping fixed with hot melt glue.The product is BIFMA and FSC certified .

TABLE TOP L SHAPED . PRIMARY WORK SURFACE OVER ALL SIZE IS 1800MM(L)X 900MM(D)X 760MM(H) 50MM THICK TABLE TOP MADE OF PRELAMINATED PARTICLE BOARD WORK SURFACE WITH CLASSIC WENGE BROWN FINISH 2MM THICK PVC EDGE BANDING MADE OF SAME MATTE FINISH. SIDE PANNEL IS MADE OF 50MM THICK * PROVISION OF SIDE RUNNER OF SIZE IS 1200MM(L)X 400MM(D)X 760MM(H) ,(CCOMBINATION ONSTRUCTION BELOW TABLE TOP 1 KEY BOARD TRAY IN PVC WITH TELESCOPIC CHANNEL ON RIGHT SIDE IS MOVABLE SIDE RUNNER HAVING 1 OPENABLE DOOR WITH 1 FIXED SHELVE, 1 OPEN BOX WITH 1 FIXED SHELVE UPPER SHELVE HEIGHT IS @ 320MM BELOW SHELVE HEIGHT IS @324@ + 3 DRAWERS (2 EQUAL DRAWERS + 1 FILLING DRAWER)PER DRAWER HEIGHT IS @ 184MM, FILLING DRAWER HEIGHT IS @ 303MM HAVE CENTRAL LOCK AND HANDLES WITH CASTORS . * MOBILE PEDESTAL OF SIZE 400MM(L)X 530MM(D)X 671MM(H) ,PER DRAWER HEIGHT IS @ 186MM, FILLING DRAWER HEIGHT IS @ 195MM HAVING (2 EQUAL DRAWERS + 1 FILLING DRAWER) IN PROVIDED WITH CETNRAL LOCK FOR SECURITY AND HANDLES ARE PROVIDED FOR EASY OF OPENING. OVERALL CONSTRUCTION OF PEDESTAL IS 18 MM ALONG WITH FECIA OF DRAWERS. * THREE LAYER PRELAMINATED PARTICLES BOARD(WOOD PRODUCT) OF GRADE II TYPE III OF IS 12823/LATEST

Providing and supplying high back chair. The seat shall be made of 15mm thick hot pressed commercial plywood upholstered with high resilience polyurethane foam (40+16) mm thick having density of min 40kg/m³ with foam net tapestry of approx. 0.9mm thick and 300 GSM and the back shall be made of 19mm dia. MS chrome pipe upholstered with breathable mesh tapestry. The backrest of the chair shall be made by keeping the natural curvature of the spine with contoured lumbar support having cushion pad as well as headrest support. The seat and back shall be arrested together with powder coated HR steel spine and the armrest shall be used adjustable PU arm completely joint with seat. It shall have synchro knee tilt 360 degree revolving mechanism with min four position locking and tilt tension adjustment with anti-shock feature. The pneumatic seat height adjustment for healthy seating, user can adjust seat height up to 65mm with BIFMA standard class-3 gas-lift to suit them using the lever under the seat. The gas-lift mechanism should be tested as per ANSI/BIFMA X5.1-2011 standard. The pedestal should have five legged MS/CRCA chrome plated having pitch circle Dia. 700 mm fitted with 5 nos. twin wheel castors. The castor of the chair should be injection moulded in black nylon 30% glass filled, confirming to ANSI/BIFMA X5.1-2011 standard tested to perform 98,000 cycles with 250lbs load. The seat size shall be 490±10 mm(W) X 470±10mm(D) and back size shall be 700±10 mm(H) from seat & overall height = 1170±10 mm.

SUPPLYING & PLACING BACK STORAGE UNIT IN COMPLETELY KNOCK DOWN CONDITIONS WITH AN OVERALL SIZE 3000MM X 450MM X 900MM THAT IS TO BE ASSEMBLED AT SITE. THE TOP SHALL BE MADE UP OF MEDIUM DENSITY FIBRE-BOARD WITH APPROVED VENEER LAMINATE AND PU POLISH ACCORDINGLY. THE PANEL SHALL BE IN RECTANGLE SHAPE AND SHOULD BE 75MM THICK. VENEERED PORTION OF WORK SURFACE SHALL BE FINISH WITH PU POLISH. THE EDGES OF THE TABLE SHALL BE SUPPLIED WITH SOLID BRASS BAR STRIPS HAVING CROSS-SECTION AREA 25MM X 5MM ALL AROUND THE TOP. THE COMPLETE UNIT SHALL BE MADE UP OF MEDIUM DENSITY FIBRE-BOARD DULY VENEER LAMINATE AND PU POLISH. IT SHALL HAVE 4 NOS. OF DOOR SHUTTER OPERATED WITH THE ASSISTANCE OF SOFT-CLOSE CONCEALED CRANK HINGE AND 4 NOS. OF DRAWER OPERATED ON SOFT- CLOSE BALL BEARING SLIDING CHANNEL. THE UNDERSTRUCTURE SHALL CONSIST OF MS/CRCA POWDER COATED RECTANGLE PIPE FRAME HAVING CROSS-SECTION AREA 40X20MM WITH 1.6MM THICK. THE UNIT HAVE TO BE MADE IN SUCH A WAY THAT NO GAP SHOULD BE SEEN IN BETWEEN. ALL THE SIZE SHALL HAVE THE TOLERANCE OF UPPER AND LOWER DEVIATION OF ±10MM FOR BOARD & ±0.2MM FOR METAL. .THE PRODUCT MUST BE FROM A MANUFACTURER HAVING ISO 9001,ISO 14001 ,,AIOTA ,BIFMA COMPLIANT, GREEN GUARD,SEDEX CERTIFICATE. MAKE DURIAN.WARRANTY-5YEARS,

Providing and Placing in position of Two Seater Sofa as per image. The contemporary designed sofa of Size : (L)155.0cm X (D)91.0cm X (H)87.0cm, seat height 44.5cm, seat depth 52.0cm, arm height 62.5cm, inner seating width 107.0cm and back height 41.0cm, should be upholstered in premium leather, this sofa is sleek and comfortable. Premium leather upholstery that is stretched out by hand onto the foam for a sumptuous seat. The sofa is a covered in a combination of leather and leatherette with all the areas you can experiece are finished in leather and non-functional areas are finished in leatherette. The puffy arms and backrest comes with a beautiful panel detail along with tufted side arms for added design. The soft foam cushions coupled with the solid wood base makes for a classy sofa set.The back and seat have medium to firm cushioning for better posture. Finished in a luxurious Leather, the sofa exudes a certain class. Seat of Sofa is layered with silicon fibre filling over high density foam. The seat cushion is made of multi layered foam of density 32(+/-2kg /m3). The seating cushions have 2.75 & 1.75 inches of elastic webbing. The thread used is nylon bonded to provide lasting stitch strength. Complete as per direction of Engineer -in –Charge.

Providing and Placing in position of Single Seater Sofa as per image. The contemporary designed sofa of Size : (L)102.5cm X (D)91.0cm X (H)87.0cm, seat height 44.5cm, seat depth 52.0cm, arm height 62.5cm, inner seating width 53.5cm and back height 41.0cm, should be upholstered in premium leather, this sofa is sleek and comfortable. Premium leather upholstery that is stretched out by hand onto the foam for a sumptuous seat. The sofa is a covered in a combination of leather and leatherette with all the areas you can experiece are finished in leather and non-functional areas are finished in leatherette. The puffy arms and backrest comes with a beautiful panel detail along with tufted side arms for added design. The soft foam cushions coupled with the solid wood base makes for a classy sofa set.The back and seat have medium to firm cushioning for better posture. Finished in a luxurious Leather, the sofa exudes a certain class. Seat of Sofa is layered with silicon fibre filling over high density foam. The seat cushion is made of multi layered foam of density 32(+/-2kg /m3). The seating cushions have 2.75 & 1.75 inches of elastic webbing. The thread used is nylon bonded to provide lasting stitch strength. Complete as per direction of Engineer -in –Charge.

Supplying and placing Of Conference Table,*SUPPLYING, AND PLACING IN POSITION CONFERENCE ROOM TABLE, OFFERS YOU A GENEROUS WORKSPACE,DESK PRIMARY WORK SURFACE USE PREMIUM QUALITY MATERIALS. TABLE TOP SHALL BE MADE OUT OF 36 MM THICK PRE-LAMINATED PARTICLE BOARD OF GRADE II TYPE III OF IS 12823/LATEST,CONSTRUCTION PROVISION THE OVAL SHAPED CONFERENCE TABLE OVER ALL SIZE IS 4800MM (L) X 1800MM (D) X 750MM (H) MADE OUT OF 36 MM THICK PRELAMINATED PARTICLE BOARD AND TOP BASED ON SIDE PANEL SHALL BE MADE OUT OF 18MM THICK PRELAMINATED PARTICLE BOARD SIZE IS 400MM (L) X 715MM(H) AND BELOW THE TABLE TOP MODESTY PANEL SHALL BE MADE 18MM THICK PRELAMINATED PARTICLE BOARD SIZE IS 1559 MM(L) X 400 MM(H). * CONFERENCE TABLE EXTANDABLE PART COMES IN SEMICIRCLE SHAPED SIZE IS 1200MM(L) X 600MM(D) X 750MM (H). EXTANDABLE PART TOP MADE OUT OF 25MM THICK IN PRELAMINATED PARTICLE BOARD.TOP BASED ON CENTER PANEL SHALL BE MADE OUT OF 18MM THICK PRELAMINATED PARTICLE BOARD SIZE IS 400MM (L) X 715 MM(H) AND BELOW THE EXTANDABLE PART TOP MODESTY PANEL SHALL BE MADE 18MM THK PRE-LAMINATED PARTICLE BOARD SIZE IS 200 MM(L) X 400 MM(H) .WHEN THE EXTANDABLE PART AND TABLE FIXED TOGHETHER SUPPORTING WITH 18MM THK PRELAMINATED PARTICLE BOARD BOX SIZE IS 209 MM(L) X 400 MM(H).OUR WORK SURFACE FURNITURE IS FINISHED WITH EXPOSED EDGES SHALL BE FINISHED WITH 2MM THICK EDGE BINDING TAPE OF MATCHING COLOUR AND SHADE,FIXED WITH HOT MELT GLUE.The product must be from a Manufacturer having ISO 9001,ISO 14001 ,AIOTA ,BIFMA COMPLIANT, GREEN GUARD,SEDEX CERTIFICATE. MAKEDURIAN.WARRANTY-5YEARS.

CORNELL/MB : MEDIUM BACK LEATHERETTE CHAIR IN BLACK COLOUR WITH MATTE FINISH MEDIUM BACK 360° DEGRE REVOLVING CHAIR SKU : CORNELL/MB , ALL OVER SIZE IS : 546MM(L)X 630MM(D)X 1160MM(H) , THE CHAIR MADE OF FULL LEATHERETTE IN BLACK COLOUR . IT WILL COMES IN MATTE FINSIH IN CONTEMPORARY STYLE . ARMS : CHROME FINISH ARMS WITH PU PADDING . USE OF PLY: 12 MM THICK HOT PRESSED BWR PLYWOOD (IS GRADE - 303 FOR SEAT AND BACK) . SEAT: 40 ± 2 MM THICK POLYURETHANE FOAM WITH DENSITY 32 (±3) KG PER CU METER FOR BEST QUALITY CUSHIONING IN SEAT , BACK : 15 ± 2 SOFT FOAM WITH BEST QUALITY CUSIONED IN BACK . * MECHANISM : TORSIONBAR MECHANISM .GAS LIFT 100 MM TELESCOPIC HAUDRAULIC, E39BASE : 650 MM CHROME BASE WITH SMOOTH CASTORS . THE SELLER / COMPANY SHOULD BE ISO 9001:2015, ISO 50001:2018, ISO 14001:2015, ISO 45001:2018 CERTIFICATES OF THE MANUFACTURER CERTIFIED BY NATIONAL ACCREDITATION BOARD OF CERTIFYING BODIES, IGBC, GREENGUARD COMPLIANCE or GREEN PRO, INDIAN DESIGN MARK COMPLIANT, GRIHA CERTIFICATE, INDOOR AIR QUALITY CERTIFICATION, FSC CERTIFICATE. THE BIDDER SHOULD BE A MEMBER OF BIFMA AND AT LEAST TWO PRODUCTS OF THE OEM SHOULD BE CERTIFIED AS BIFMA COMPLIANT AND AN OFFICIAL PRODUCT OFFICIAL LINK/SCREENSHOT OF THE PRODUCT LISTING MUST BE PROVIDED FROM WWW.BIFMA.ORG". and complete as per the approved sample and as per the direction of Engineer-In-Charge.

The scope of laboratory furniture shall consist of supply of raw material, fabrication, assembling, preparation of design, drawings, supply and erection. Work shall be executed in a well coordinated and professional manner.The complete M.S. material of cabinet to be pre – treated (degreased, Zinc Phosphated) and epoxy powder coated for better corrosion resistance. The thickness of powder coat to be 70 to 80 microns, which passes the Salt Spray test for 1000 hours and having the Scratch Hardness of 3Kgs 18± 2mm thick Jet Black granite top with moulding of approved design on the front edge. Groove at the bottom of granite after leaving 25 mm from the front to avoid liquid spillage.The pedestal frame shall be made of high quality ERW steel tubes of size 30 mm x 30 mm x 1.5 mm. Pedestal shall be finished in approved color with epoxy polyester powder coating. Leveling screws will be provided at the bottom of the tubular legs and the same shall be covered by means of black plastic spats for good aesthetics.CRCA MS sheet/ PVC Trunking with inbuilt division for laying Electrical/Data & voice cabling facilities shall be given: 100mm x 50mm thick. 1.5mm to 2.5 sq mm. wires shall be used. The termination with end connector shall be at the end of the Truncking. (Necessary connections can be provided)

.NLT 50 micron thickness Epoxy powder coating (approved colors) shall be done on all modules and on all pedestals. The EIGHT (8) tank pre treatment shall be given before the powder coating. One piece moulded non reactive PP sinks shall be given in the furniture.Option of supplying on demand S.S 304 or S.S316 or Ceramic sink shall be given and will be quoted separately. All fittings shall bear a guaranteed life of minimum one year. 1) Hinges:- Corrosion resistant CED Coated hinges shall be supplied with all the modules. 2) Handles:-All handles shall be of SS 304/ Alu concealed Handles Handless may be in two tones or single tone. 3) Brand of Locks:- Godrej/Ebco. 4) Brands for Electrical Fittings:- Northwest or equivalent make 230V, 6/15Amp, with 3 pin socket in each 1.5 mtr and piano switches, or Industrial switches & sockets shall be provided. 5) Utility : 3 way/ 1 way taps:- Taps will be epoxy powder coated , with DIN 12920 cooler coding, or S.S taps as per the requirement. Laboratory Workbench provided as per layout in combination of 1800 x 750 x 850 (with storage cabinet)

Centre Table:-Size 1200 mm wide x 600 mm depth x 450 mm height.Center Table with 8mm thick Clear Glass top, Under-structure verticals are made up of 50mm thick MDF with 0.4mm thk European PVC foil & Horizontal support from 50mm thick Prelaminated MDF.All sides to have 0.8mm thk edge band.

Add 18% GST

Add 1% Labour cess 1%

M/s Raj Construction (BID ID -651319)

M/S MADAN PRASAD (BID ID -650125)