Aesthetics work of Bahu Fort Park, Common facade including new entrance of Bahu Fort Market, old parking area and Road side features near Bahu Fort Jammu under smart city Mission.

Amount

Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 meters lead as per direction of Engineer-incharge:1:3:6 or richer mix (i/c equivalent design mix)

Demolishing cement concrete manually/by mechanical means including disposal of material within 50 meters lead as per direction of Engineer-incharge:1:4:8 or leaner mix (i/c equivalent design mix)

Dismantling tile work in floors and roofs laid in cement mortar includingstacking material within 50 meters lead. For thickness of tiles above 25 mm and upto 40 mm.

Demolishing stone rubble masonry manually/by mechanical meansincluding stacking of serviceable material and disposal of unserviceablematerial within 50 meters lead as per direction of Engineer-in-charge: In cement mortar

Dismantling steel work in built up sections in angles, tees, flats andchannels including all gusset plates, bolts, nuts, cutting rivets, welding etc.including dismembering and stacking within 50 meters lead.

Demolishing brick work manually/by mechanical means includingstacking of serviceable material and disposal of unserviceable materialwithin 50 meters lead as per direction of Engineer-in-charge:In cement mortar

Earth work in excavation by manual means in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed:All kinds of soil :

Disposal of surplus Earth by mechincal Transpotation including loading and unloading complete Job upto 5 kilometer.

Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with:1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size)

Providing and laying in position cement concrete of specified grade including curing butexcluding the cost of centring and shuttering. All work upto plinth level with: 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 20 mm nominal size)

Providing and laying in position cement concrete of specified grade including curing butexcluding the cost of centring and shuttering. All work upto plinth level with: 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

Providing and laying in position specified grade of reinforced cement concrete including curing but excluding the cost of centering, shuttering, finishing and reinforcement. All works upto plinth level1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15°, landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto five level including curing but excluding the cost of centring, shuttering, finishing and reinforcement with 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in walls (any thickness) including attached pilasters,buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts upto floor five level including curing but excluding cost of centering shuttering,finishing and einforcement1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size)

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level Thermo-Mechanically Treated bars of grade Fe-500D or more.

Centering and shuttering including strutting, propping etc. and removal of form for:Suspended floors, roofs, landings, balconies and access platforms

Centering and shuttering including strutting, propping etc. and removal of form for:Edges of slabs and breaks in floors and walls under 20 cm wide

Wall murals 3D made in Cement mudium with Red/Jasial mare stone look debeicing story of deffernt religinous places etc. in with multi colour.

Centering and shuttering including strutting, propping etc. and removal of form for: Foundations, footings, bases of columns etc. for mass concrete

Stone work (machine cut edges) for wall lining etc. (veneer work) upto 10 m height,backing filled with a grout of average 12 mm thick cement mortar 1:3 ( 1cement: 3 coarsesand) including pointing in white cement mortar 1:2 ( 1 White cement: 2 stone dust) withan admixture of pigment matching the stone shade and curing complete : (To be securedto the backing by means of cramps which shall be paid for separately):30mm thick Red sand stone of unifirm shade and without any doots on spots

40 mm thick fine dressed and rubbed stone flooring over 20mm(average) thick base of cement mortar 1:5 (1 cement: 5 coarse sand),with joints 3mm thick, side buttered with cement mortar 1:2 (1 cement :2 stone dust) admixture with pigment to match the shade of stone and pointing with the same mortar and curing complete Red sand stone unifirm shade and without any doots on spots

Providing and fixing cramps of required size and shape for anchoring stone wall lining tothe backing or securing adjacent stones in stone wall lining in cement mortar 1:2 (1 cement: 2 coarse sand) including making the necessary chases in stone and holes in walls wherever required Gunmetal Cramps 25 x 6 mm - 30 cm long

Brick work with common burnt clay (non-modular) bricks of class designation 7.5 in foundation and plinth including curing in :Cement mortar 1:4 ( 1 cement : 4 coarse sand)

Brick work with common burnt clay (non-modular) bricks of class designation 7.5 infoundation and plinth including curing in :Cement mortar 1:6 ( 1 cement : 6 coarse sand)

Extra for brick work with common burnt clay bricks/cement concrete bricks insuperstructure above plinth level upto floor five level

12mm Cement plaster of mix 1 : 6 ( 1 cement : 6 fine sand)

12mm Cement plaster of mix:1 : 4 ( 1 cement : 4 fine sand)

Providing and fixing of 2'.6'' Red / Pink sand stone Jaffery Railing of 6 ft long on wall with 4''x4''x3' pillars for supporting including necessary moulding of edges finishing with melamine coating of specified quality of approved shade fixing with arldite etc. including foundation work as directed by Engineer-incharge

Steel work welded in built up sections/framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates andsimilar works.

Steel work in built up tubular (round, square or rectangular hollow tubesetc.) trusses etc., including cutting , hoisting , fixing in position andapplying a priming coat of approved steel primer, including welding andbolted with special shaped washers etc. complete. Hot finished welded type tubes

Steel work welded in built up sections/framed work, including cutting,hoisting, fixing in position and applying a priming coat of approved steelprimer using structural steel etc. as required.In stringers, treads, landings etc. of stair cases, including use ofchequered plate wherever required, all complete.

Extra for pre finished nosing in treads of steps of kota stone/ sand stoneslab.

Half brick masonry with common burnt clay (non-modular) bricks of class designation 7.5 in foundations and plinth including curing inCement mortar 1:4 ( 1 cement : 4 coarse sand)

Providing and laying Polished Granite stone flooring with fine and closed grains in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed and approved by the Engineer-in-Charge. Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent

Providing edge moulding to 18 mm/16 mm thick marble stone counters, Vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge.Granite Work

Extra for half Brick masonry in superstructure above plinth level upto floor V level.

Finishing walls with textured exterior paint of required shade on New work (two or more coats applied @ 3.28 liter/10sqm) over and including base coat of exterior primer applied @ 2.20kg/10sqm

Finishing with Deluxe multi surface paint system for interiors and exteriors using primer as per manufacturers’ specifications:Painting steel work with deluxe multi surface paint ofrequired shade to give an even shade. Two or more coats applied @0.90litre/10sqm over an under coat of primer applied @ 0.80litre/10sqm ofapproved brand and manufacture

Painting with synthetic enamel paint of approved brand and manufactureto give an even shade.Two or more coats on new work over an under coat ofsuitable shade with ordinary paint of approved brand and manufacture.

Removing mortar from bricks and cleaning bricks including stacking within a lead of 50 m. (stacks of cleaned bricks shall be measured) :From brick work in cement mortar

Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with:1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

Providing and fixing adjustable stainless steel cramps of approved quality and of required shape and size adjustable with stainless steel nuts, bolts and washers (total weight not less than 260gms) for dry stone cladding fixed on frame work at suitable location including making necessary recesses in stone slab, drilling required holes etc. complete as per the direction of engineer-in-charge.

Providing and fixing G.I. chain link fabric fencing of required width inmesh size 25x25 mm made of G.I. wire of dia 3 mm includingstrengthening with 2 mm dia wire or nuts, bolts and washers as requiredcomplete as per the direction of Engineer-in-charge.

Providing and fixing stainless steel (Grade 304) railing made of Hollowtubes channels, plates etc. including welding ,grinding, buffing, polishingand making curvature (wherever required) and fitting the same withnecessary stainless steel nuts and bolts complete ,including fixing the railing with necessary accessories and stainless steel dash fasteners, stainless steelbolts etc. of required size, on the top of the floor or the side of waist slabwith suitable arrangement as per approval of Engineer-in-charge, (forpayment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Providing and fixing precoated galvanized iron profile sheets (size, shapeand pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+0.05 %) total coated thickness with zinc coating 120 grams per sqm as perIS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side ofthe sheet and polyester top coat 15-18 microns. Sheet should haveprotective guard film of 25 microns minimum to avoid scratches duringtransportation and should be supplied in single length upto 12 metre or asdesired by Engineer-in-charge. The sheet shall be fixed using self drilling/self tapping screws of size (5.5x 55 mm) with EPDM seal, complete uptoany pitch in horizontal/ vertical or curved surfaces, excluding the cost ofpurlins, rafters and trusses and including cutting to size and shapewherever required

providing and fixing Aluminium composite panel sheet for false ceilling of roof with 3mm thick sheet one face design and other side plane of approved brand and manufacture with in all including necessary fitting anf fixtures

providing and fixing Aluminium composite panel sheet for wall panelling with 6mm thick of superior quality sheet 1 face design and other side plane of approved brand and manufacture with in all including necessary fitting anf fixtures

Finishing with Deluxe multi surface paint system for interiors andexteriors using primer as per manufacturers’ specifications:Two or more coats applied @ 1.25 liter/10sqm over andincluding one coat of special primer applied @ 0.75liter /10sqm

Removal of unhygienic materials (so classified by the site engineer) from designated sites and its disposal as per directions, all inclusive.

Providing & making Gabion structure with Mechanically Woven DoubleTwisted Hexagonal Shaped Wire mesh Gabion Boxes as per IS16014:2012,MORTH Clause 2500, of required size, Mesh Type10x12(D=100 mm with tolerance of ±2%), Zinic+10% Al alloy+PVCcoated, Mesh wire diameter 2.7/3.7mm (ID/OD), mechanically edged/selvedged with partitions at every 1m interval and shall have minimum 10 numbers of openings per meter of mesh perpendicular to twist, tying withlacing wire of diameter 2.2/3.2mm(ID/OD), supplied @3% by weight ofGabion boxes, filled with boulders with least dimension of 200 mm, as perdrawing, all complete as per directions of Engineer-in-charge.

Cement Mortar 1 : 6 (1 cement: 6 coarse sand) for fiiling of voids of gabian stones complete with labour and over heads

Filling available excavated earth (excluding rock) in trenches, plinth, sides offoundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead upto 50 m and lift upto 1.5 m.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,having thermal stability for hot and cold water supply, including allCPVC plain and brass threaded fittings. This includes jointing of pipesand fittings with one step CPVC solvent cement and testing of jointscomplete as per direction of Engineer-in-charge.Internal work-concealed fixing the pipe with clamps at 1.00 Mtr spacing including cuttiing chases and making good the wll etc 20mm nominal outer dia pipes.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,having thermal stability for hot and cold water supply, including all CPVC plain and brass threaded fittings. This includes jointing of pipesand fittings with one step CPVC solvent cement and testing of jointscomplete as per direction of Engineer-in-charge.Internal work-exposed on wall, including fixing the pipewith clamps at 1.00 meter Internal work-oncealed fixing the pipe with clamps at 1.00 Mtr spacing including cuttiing chases and making good the wll etc 25mm nominal outer dia pipes.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,having thermal stability for hot and cold water supply, including allCPVC plain and brass threaded fittings. This includes jointing of pipesand fittings with one step CPVC solvent cement and testing of jointscomplete as per direction of Engineer-in-charge.Internal work-exposed on wall, including fixing the pipewith clamps at 1.00 meter Internal work-oncealed fixing the pipe with clamps at 1.00 Mtr spacing including cuttiing chases and making good the wll etc 32mm nominal outer dia pipes.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,having thermal stability for hot and cold water supply, including allCPVC plain and brass threaded fittings. This includes jointing of pipesand fittings with one step CPVC solvent cement and testing of jointscomplete as per direction of Engineer-in-charge. External work including trenching, refilling etc.40mm nominal outer dia pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,having thermal stability for hot and cold water supply, including allCPVC plain and brass threaded fittings. This includes jointing of pipesand fittings with one step CPVC solvent cement and testing of jointscomplete as per direction of Engineer-in-charge. External work including trenching, refilling etc.50mm nominal outer dia pipes

Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank

Chequerred precast cement concrete tiles 22mm thick in footpath andcourtyard, jointed with neat cement slurry mixed with pigment to matchthe shade of the tiles, including rubbing, cleaning and curing complete,on 20 mm thick bed of cement mortar 1:4 ( 1 cement : 4 coarse sand) Dark shade using ordinary cement. highly compressed as per approved brand and manifacture

Providing & fixing for signage Boards in Ms frame and 18 gauge sheet Size .6" x 1' with Ms sheet fixed on square angle frame of ( 32x32 4mm angle ) with vertical angle 40x40x 4mm angle including polish, writing as directed by Engineer- incharge (Complete items)

Providing and laying damp-proof Course 50 mm thick with cement concrete 1:2:4 (1 cement:2 coarse sand: 4 graded stone aggregate 20 mm nominal size) and curing complete

Finishing walls with acrylic smooth exterior paint of required shade on New work (Two or more coats applied @ 1.67 liter/10sqm over and including priming coat of exterior primer applied @ 2.20kg/10sqm

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS : 15622(thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer- in-Charge, inskirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 ( 1 cement :3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointingin white cement mixed with pigment of matching shade complete (2'x6") size of tiles as fixed with epoxy excluding cost and labour of epoxy

Providing and fixing Glass mossaic tiles at finished plain wall surface ofsize 20 mm x 20 mm x 4 mm in all colour, design, fixing in customizedesign as per direction of Engineer-in- Charge. The glass mosaic tiles tobe fixed on the wall surface with the help of approved adhesive appliedat the rate of 2.5 kg per sqm and grouting of the same. The rate isinclusive of all operation, material and required pattern approved byEngineer-in-Charge:

Providing and mixing water proofing material in cement concrete work in doses by weight of cement as per manufacturer’s specification. (1 kg of water proofing material in 50 kg of cement

12mm Cement plaster finished with a floating coat of neat cement of mix: 1 : 3 ( 1 cement : 3 fine sand)

Providing and fixing un-plasticised -PVC pipe clips of approved design toun-plasticised - PVC rain water pipes by means of 50x50x50 mm hardwood plugs, screwed with M.S. screws of required length, includingcutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarsesand) and making good the wall etc. complete 110 mm

Constructing brick masonry chamber for underground C.I. inspection chamber and bend with common burnt clay (non modular) bricks of class designation 7.5 in cement mortar 1:4 ( 1 cement : 4 coarse sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg ) R.C.C. top slab with 1:1 ½ : 3 mix ( 1 cement : 1 ½ coarse sand : 3 graded stone aggregate 20 mm nominal size),foundation concrete 1:5:10 (1 cement: 5 fine sand: 10 graded stone aggregate 40mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 ( 1 cement : 3 coarse sand) finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design : Inside dimensions 455x610 mm and 45 cm deep for single pipe line

Varnishing with flatting varnish of approved brand and manufacture one or more coats on old work

Random Rubble masonry with hard stone in superstructure above plinth level and upto floor five level, including levelling up with cement concrete 1:6:12 (1 Cement : 6 coarse sand : 12 graded stone aggregate 20mm nominal size) and curing complete at window sills, ceiling level and the like:Cement mortar 1:6 (1 Cement : 6 coarse sand) Nallah

Painting with synthetic enamel paint of approved brand and manufactureto give an even shadeTwo or more coats on new work

Surface dressing of the ground including removing vegetation and in-equalities not exceeding 15 cm deep and disposal of rubbish, lead upto 50 m and lift upto 1.5 m in -All kinds of soil.

Supplying and stacking of good earth at site including royalty (earthmeasured in stacks will be reduced by 20% for payment)

Supplying and stacking of well decayed cow dung manure at siteincluding royalty (cow dung manure measured in stacks will be reducedby 8% for payment)

Mixing earth and sludge or manure in proportion specified or directed byofficer in charge.

Spreading of sludge, dump manure or/and good earth in requiredthickness as per directions of officer in-charge (cost of sludge, dumpmanure or/and good earth to be paid separately)

Providing and laying factory made chamfered edge Cement Concretepaver blocks in footpath, parks, lawns, drive ways or light traffic parkingetc, of required strength, thickness & size/ shape, made by table vibratorymethod using PU mould, laid in required colou r& pattern over 50mmthick compacted bed of sand, compacting and proper embedding/laying ofinter locking paver blocks into the sand bedding layer through vibratorycompaction by using plate vibrator, filling the joints with sand and cuttingof paver blocks as per required size and pattern, finishing and sweepingextra sand complete all as per direction of Engineer-in-Charge.60mm thick cement concrete paver block of M-35 grade withapproved colour, design & pattern

Providing & plantation of Golden junipres 3-4 ft height

Providing & plantation of pencil pine 4-5 ft

Providing & plantation of Junipers Ball-ball (12'p.b)developed 4-5 ft

Providing & plantation of euphorba 2-3 ft

Providing & plantation of Rose hybrid (P.B)

Providing & plantation of Sameravia 8" pot (P.B)

Providing & plantation of Noline

Providing & plantation of Golden Juniperas silver pine 4 ft Height

Providing & plantation of phoemin palm (3ft)

Providing & plantation of coropetlum (2-3 ft hight)

Providing and fixing M.S tree guard 45 cm square in plan, height 1.20meter above ground level and 0.40 meter below ground level. Thevertical members shall consist of four nos. angle iron of size 25x25x3mm, 1.6 m long, one at each corner and 8 nos flat iron of size 25x3 mm,1.2 m long. The vertical members shall be welded to 4 nos. 25x6 mmM.S flats placed horizontally around the vertical members of the cage.One name plate of 1 mm thick M.S sheet of size 250x100 mm shall bewelded to the tree guard near the middle height and lettered CPWD/PWD/any other approved name. The tree guard shall be fixed to theground by making suitable holes and by embedding four corners leg inthe ground, including refilling the earth, compaction etc. complete. Thetree guard shall be painted with two more coats of synthetic enamelpaint of approved brand and or more coats of synthetic enamel paint ofapproved brand and manufacture over a coat of primer complete

Providing and fixing of Red stone 40 mm thick carving asthetics work on it, design and carving, as approved by Engineer-in -charges at Dyodi on the entry of Bahu Fort Market (As per sample photographes attached)

Stone work (machine cut edges) for wall lining etc. (veneer work) upto 10 m height,backing filled with a grout of average 12 mm thick cement mortar 1:3 ( 1cement: 3 coarsesand) including pointing in white cement mortar 1:2 ( 1 White cement: 2 stone dust) withan admixture of pigment matching the stone shade and curing complete : (To be securedto the backing by means of cramps which shall be paid for separately):Red sand stone - exposed face fine dressed with rough backing 70mm thick

Providing and fixing on wall face un-plasticized Rigid PVC rain waterpipes conforming to IS: 13592 Type A including jointing with seal ringconforming to IS: 5382 leaving 10 mm gap for thermal expansion 75 mm diametre single socket pipe

Providing and laying anti-skid Ceramic glazed floor tiles 300x300 mm (thicknessto be specified by the manufacturers) of 1st quality conforming to IS:15622 of approved make, laid on 20 mm thick bed of cement mortar 1: 4( 1 cement : 4 coarse sand) including pointing the joints with whitecement and matching pigment etc., complete. In colour such as White, Ivory, Grey, Fume Red Brown (1'-1') to( 1.6' x1.6') as directed by Engineer Incharged

Finishing walls with water proofing cement paint of required shade onNew work (two or more coats applied @ 3.84 kg/10sqm)

Distempering with 1st quality acrylic distemper (ready mixed)havingVOC content less than 50 gms/litre, two or more coats on new work ofapproved manufacturer, of required shade and colour complete as permanufacturer’s specifications

Providing and fixing powder coated aluminium work (minimumthickness of powder coating 50 micron) consisting of tee/ angle sections,of approved make conforming to IS : 733 in frames of false ceilingincluding aluminium angle cleats with necessary C.P. brass/ stainlesssteel sunk screws, aluminium perimeter angles fixed to wall withstainless steel rawl plugs @ 450 mm centre to centre and fixing the frame work to G.I. level adjusting hangers 6 mm dia. with necessarycadmium plated machine screws all complete as per pprovedarchitectural drawings and direction of the Engineer-in-charge (leveladjusting hangers, ceiling cleats and expansion hold fasteners to be paid for separately).

Providing and fixing 12mm thick prelaminated particle board flatpressed three layer or graded wood particle board (conforming to IS:12823 Grade-I type-II) in panelling fixed in aluminum doors, windowsshutters and partition frames with C.P. brass / stainless steel screws etc.complete as per architectural drawings and directions of engineer-incharge.Pre-laminated particle board with decorative lamination on bothsides.

Providing and fixing aluminum handles ISI marked anodized (anodic coatingnot less than grade AC 10 as per IS: 1868) transparent or dyed to requiredcolour and shade with necessary screws etc. complete. 125 mm

Providing and fixing aluminum tower bolts ISI marked anodized (anodiccoating not less than grade AC 10 as per IS : 1868) transparent or dyed torequired colour or shade with necessary screws etc. complete 200x10 mm

Providing and fixing water closet squating pan (Indian type W.C. pan) with 100 mm sand cast,Iron P or S trap.10 liter low level white P.V.C flushing cisten . Including flush pipe ( of approval make) with manually controlled device (handle lever) conforming ro IS :7231, with all fittings abd fixtures complete. Including cutting and making good the walls and floor where required: White vitreous china Orissa pattern W.C. pan of size 580x440 mm with intergral type foot rests.

Providing anf fixing white vitreius china pedestal type water closet (Europen type) with seat and lid. 10 liter low level white vetreous china flushing cistern and CP flush bend with fittings and C.I. brackets, 40mm flush bend, overflow arrangment with specials of standard make and including paintings of fittings and bracket, cuttings and making good the walls and floors wherever required. W.C . Pan with ISI marked white solid plastics seat and lid.

Providing and fixing wash basin with C.I brackets 15mm C.P brass pillars Taps,32 C.P.brass wate of standard pattern.Including paintings of fittings and brackets cuttings and making good the walls wherever required. White Viterious China Flat back wash basin size 550x400mm with single 15 mm C.P brass pillars tap.

Providing and fixing white viterious china pedestal type (Europen type / wash down type) water closet pan.

Providing and fixing of 15mm nominal bore CP brass bib cock of approved quality conforming to IS :8931

Providing and fixing white viterious china flat back half stall urinal of size 580x380x350mm with white P.V.C automatic flushing cisten, with fittings standard size C.P Brass flush pipe,spreaders with unions and clamps (all in C.P. brass) with waste fittings as per IS:2556,C.I trap with outlet gratings and othet couplings in C.P. brass,including paintings of fittings and cuttings making good the wall and floors wherever required:Single half stall urinal with 5 liters P.V.C automatic flushing cistern

Providing and fixing 600x120x5mm glass shelf with edges round off supported on anodized aliminimum angle frame with C.P brass brackets and guard rail complete fixed with 40 mm long screw rawl plugs etc complete

Providing and fixing 600x450 mm beleved edge mirror of superior glass ( of approved quality) complete with 6mm thick hard board ground fixed to wooden cleats with C.P brass screw and washers complete

Providing and fixing of PVC wate pipe for sink or wash basin including P.V.C waste fittings complete :32 mm dia Semi rigid pipe.

providing and fixing PTMP 15mm Yrinal spreader size 95x69x100mm with 1/2" Bsp thread and shapes,weight not less than 60 grm.

Supply and fixing of water pump 2 HP making of kriloskerr or crompton

Providing and fixing ball valve (brass) of approved quality, High or lowpressure, with plastic floats complete:20 mm nominal bore

Providinga and fixing of floor trap 75x75 mm

Providing and fixing PTMT Ball cock of approved quality, colour andmake complete with epoxy coated aluminium rod with L.P/H.P.H.Dplastic balls 20mm nominal bore, 120mm long, weighing not less than 198gms

Providing and fixing PTMT Ball cock of approved quality, colour andmake complete with epoxy coated aluminium rod with L.P/H.P.H.Dplastic balls 152mm nominal bore, 120mm long, weighing not less than 440 gms

Providing and fixing 15 mm nominal bore C.P. brass angle valve forbasin mixer and geyser points of approved make conforming to IS : 8931

Providing and fixing on wall face un-plasticized Rigid PVC rain waterpipes conforming to IS: 13592 Type A including jointing with seal ringconforming to IS: 5382 leaving 10 mm gap for thermal expansion(i) Single socketed pipes 110 mm diametre

Providing and fixing on wall face un-plasticized - PVC mouldedfittings/accessories for un plasticized Rigid PVC rain water pipesconforming to IS : 13592 Type A including jointing with seal ringconforming to IS : 5382 leaving 10 mm gap for thermal expansion 75 mm bend 87.5

Providing and fixing on wall face un-plasticized - PVC mouldedfittings/accessories for un plasticized Rigid PVC rain water pipesconforming to IS : 13592 Type A including jointing with seal ringconforming to IS : 5382 leaving 10 mm gap for thermal expansion 110 mm bend,87.5

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screw with concealed fittings arrangment of approval quality and colour:450mm long towel rail with total length of 495 mm,78mm wide and effective height of 88 mm, weighting not less than 170 gms

providing and fixing PTMT Liquid soap container 109 mm wide.125 mm high and 112mm distance from wall of standard shape with brackets of the same materials witth snap fittings of approval quality and colour weighing not less than 105 gms

40 mm thick fine dressed and rubbed stone flooring over 20mm(average) thick base of cement mortar 1:5 (1 cement: 5 coarse sand),with joints 3mm thick, side buttered with cement mortar 1:2 (1 cement :2 stone dust) admixture with pigment to match the shade of stone andpointing with the same mortar and curing complete. Red sand stone

Providing and fixing cramps of required size and shape for anchoring stone wall lining to the backing or securing adjacent stones in stone wall lining in cement mortar 1:2 (1cement: 2 coarse sand) including making the necessary chases in stone and holes inwalls wherever required Gunmetal Cramps 25 x 6 mm - 15 to 20 cm long

providing and fixing of red stone 40mm thick carving and asthetcics work on it, design and carving as approved by Engineer- in - charged at dyodi on the entry of Bahu Foprt Market

Stone work, in red sand stone plain in copings, cornices, string courses and plinth courses,upto 75mm thick, in cement mortar 1:6 (1 cement : 6 Coarse sand)including pointing with white cement mortar 1:2 (1 cement : 2 Stone dust)with an admixture of pigment matching the stone shade& curing complete.Red sand stone (Any size and asthetic design as directed bY Engineer Incharge)

Stone work (machine cut edges) for wall lining etc. (veneer work) upto 10 m height,backing filled with a grout of average 12 mm thick cement mortar 1:3 ( 1cement: 3 coarse sand) including pointing in white cement mortar 1:2 ( 1 White cement: 2 stone dust) withan admixture of pigment matching the stone shade and curing complete : (To be secured to the backing by means of cramps which shall be paid for separately):50mm thick

Providing and fixing expansion hold fasteners on CC / R.C.C./brick masonry surfacebacking including drilling necessary holes and the cost of bolt etc. complete.Fastener with threaded dia 10mm

Providing and laying in position cement concrete of specified grade including curing butexcluding the cost of centring and shuttering. All work upto plinth level with1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

Extra for carving and making design on Red stone wall. For asthetic look.

Supply and fixing of Benches on fne quality Red sand Stone size 5'.0'' x1'-6" and 3" thick with padestely legs 15"x20"x5" size embede in concerete 1:2:4 funished with 40mm thick Red sand stone foundation including necessary Earth work and mud matt (stone shoukd be without folds and spots Edges of the benches to be machine moulded as directed by Engineer-in -charge.

Providing and fixing cramps of required size and shape in RCC/CC/brick masonrybacking with cement mortar 1:2 (1 cement: 2 coarse sand) including curing & drilling necessary hole in stones and embedding the cramp in the whole (fastener to be paid separately) Stainless steel cramps

providing and fixing of Awnings of Brands (Astro) complete with C-channel powder coaided arms extendable complete with fittings upto 6.0 ft width with top fabric of superior quality with pvc liminated both sides printed complete job (any colour or as directed by Engineer-in -charge) Finished size to be mezzered and paid for stone jagahalar upto 1 feet to be provided free of cost by vendor (three year warranty for frame).

providing and fixing of Tensile shed over the mediation platform with high tensile strength complete with frame work conical shaped structure finished with white/gray colour fabric of brand Serge Ferrari PVC Tensile Fabric water /fire proof blackout.supported on single suppot in MS Structure complete with painting . height and size to be directed by Engineer Incharge as per need at size

Grinding and Melamine on Red sand stone work where ever required to give highgloss finish complete

10cm thick (average) mud phaska of damped brick earth on roofs laid toslope consolidated and plastered with 25 mm thick mud mortar mixedwith bhusa at 35kg per cum of earth and gobri leaping with mix 1:1 (1clay: 1 cow dung) and covered with specified tile bricks grouted withcement mortar 1:3 (1 cement: 3 fine sand) mixed with 2% of integral waterproofing compound by weight of cement and finishing neat.With common burnt clay (non modular) brick tiles of classdesignation 10.0

Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement: 2 coarsesand: 4 stone aggregate 10 mm and down gauge), including finishing withcement mortar 1:3 (1 cement: 3 fine sand) as per standard design. In 75x75mm deep chase

Coursed rubble masonry with hard stone (first or second sort) insuperstructure above plinth level and upto floor five level including curingcomplete with:Lime mortar 1:1:1 (1 Lime putty: 1 Surkhi: 1 Fine sand)

Wiring for light point /Fan point /Exhaust point/call bell point with 1.5 sqmm F.R.L.S PVC Insulated copper conductor single core cable in surface/recess medium class P.V.C conduit with modular switch modular plate suitable G.I Box and earthing the points with 1.5 sqmm F.R.L.S PVC Insulated copper conductor .Single core cable etc as require point Group-B

Wiring for CKT/submain wiirng along with earth wire with the following sizes of F.R.L.S P.V.C insulated copper conductor single core cable in surfacce/resessed & medium class P.V.C Conduit as required 2x2.5 sqmm+1x2.5 sqmm Earth wire

Wiring for CKT/submain wiirng along with earth wire with the following sizes of F.R.L.S P.V.C insulated copper conductor single core cable in surfacce/resessed & medium class P.V.C Conduit as required 2x4 sqmm+1x4sqmm Earth Wire

Wiring for CKT/submain wiirng along with earth wire with the following sizes of F.R.L.S P.V.C insulated copper conductor single core cable in surfacce/resessed & medium class P.V.C Conduit as required 2x6 sqmm+1x6sqmm Earth Wire

Supplying and fixing following modular switches/socket on the existing modular plate and switch box including connections but excluding modular plate etc as required 5/6 Amp Switch

Supplying and fixing following modular switches/socket on the existing modular plate and switch box including connections but excluding modular plate etc as required 3Pin 5/6 AMP SOCKET

Supplying and fixing following modular switches/socket on the existing modular plate and switch box including connections but excluding modular plate etc as required15/16 Amp Switch

Supplying and fixing following modular switches/socket on the existing modular plate and switch box including connections but excluding modular plate etc as required 6pin 15/16 Amp Socket

Supplying and fixing following ratings Four poles 415 volt Isolator in the existing MCB DB complete testing and commissioning etc as requiredwith connection. 63 AMP S.P.N

Supplying and fixing 5 Amp to 32Amp rating 240/415 volt 10KA MCB s Single pole MCB

Supplying and fixing of :Tube L.E.D 20 WATT

Supplying and fixing of Bulk head with L.E.D Bulb 9 watt

Supplying and fixing of Pedistal fan

Supplying and fixing of 6mm 2 core AL Cable

Supplying and fixing of G.I wire 8 S.W.G

Chemical earthing 3mt including excavation and back fillings

S.I.TC LED Wall p6 including all taxes on line and ofline processor Transpotation and installation 10'x 7.5' 1. Product Name : P4SMD OUTDOOR VIDEO WALL LED Encap(BranD): QUQNGLI Screen Size: 10’X7.5’ LED Type: SMD Cabinet Type: MS POWDER COATED Module Size: 320X160 Maximum Viweing Distance: 3M Resolution: 80X40 Refresh Rate: 380HZ Brightness: 5000NITS Life spam: 100000HRS Power supply: 5V60A Card: NOVA CONTROL CARD FOR PLAYING SAVED IMAGES AND VIDEO

SITC OT Fibre controller installation cable

SITC Servo 5KVA copper wound

SITC of signal booster

SITC of ACP structure for LED Wall protection

AMC for one year after warranty

Wiring for CKT/Submain wiring alongwith earth wire with the following sizes of FRLS PVC insulater copper conducter single core cable in surface/recessed medium class PVC conduit as required 2x10sq.mm +1x6sq.mm earth wire

Wiring for CKT/Submain wiring alongwith earth wire with the following sizes of FRLS PVC insulater copper conducter single core cable in surface/recessed medium class PVC conduit as required 2x16 sq.mm +1x6sq.mm earth wire

Providing laying testing and commessioningl of chemical earthing maintaince free excavation of earth and back filling of good earth for installation of 3 mtr long 4.2mm dia stainless steel copper electrode filling with chemical compound as required complete job 2No for Luggage scanner 2No for LED

Bollard Lights with pillar fittings

Grouting the joints of flooring/ wall tiles having joints of 3 mm width, usingepoxy grout mix of 0.70 kg of organic coated filler of desired shade(0.10 kg of hardener and 0.20 kg of resin per kg), including filling /grouting and finishing complete as per direction of Engineer-in-charge Size of tile 500x500 mm

Grouting the joints of flooring/ wall tiles having joints of 3 mm width, usingepoxy grout mix of 0.70 kg of organic coated filler of desired shade(0.10 kg of hardener and 0.20 kg of resin per kg), including filling /grouting and finishing complete as per direction of Engineer-in-charge Size of tile 200x200mm

Providing and fixing of Pole Mounted Twin SS 202 Grade Dustbins with roof of 60 ltr capacity, weight 35 to 40 kg approxmately, easly tiltable including SS frame work complete Job.(Dimantaion14"x28") including carriage etc to site of work complete Job as per the sample approved by Engineer incharge

Ruled/ Flush pointing on Red sand stone masonry surface with lime,surkhi and marble dust mortar in the ratio 1:1.5:1/2 one lime : 1.5 surkhi ( 50% red and 50% light yellow surkhi):1/2 marble dust ( the rate isinclusive of all materials and labours involved except scaffolding)

Painting with Synthic enamal paint of approved brand and manufacture to give an even shade on old work. Tow are more coat on old works,