138WE/L-72/2020-21

Amount

Surface excavation (not exceeding) 30 cm deep and averaging 15cm deep and getting out as in hard dense soil, complete all as specified and as directed.

Excavation in trenches, not exceeding 1.5 mtr wide and not exceeding 1.5 mtr in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. not exceeding 10 Sqm on plan and not exceeding 1.5 mtr in depth and getting out in hard dense soil, complete all as specified and directed.

Excavation over area not exceeding 1.5 mtr in depth and getting out in hard dense soil, complete all as specified and directed.

Excavation over area exceeding 1.5 mtr in depth but not exceeding 3.0 m deep and getting out in hard dense soil, complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 Cms thick, complete all as specified and directed.

Removing excavated materials/ soils, not exceeding 50mtrs and depositing where directed at a level not exceeding 1.50mtrs, complete all as specified and directed.

M&L for Plain cement concrete 1:4:8 type D-2 (using 40mm graded crushed stone aggregate), as in foundation filling and mass concrete, complete all as specified and directed.

M&L for Precast cement concrete block masonry built in PCC 1:3:6, type C-1, (using 20mm graded crushed stone aggregates) masonry with solid blocks exceeding 10 cms in width and setting in mortar 1:6, complete all as specified and directed.

M&L for Precast cement concrete block masonry built in PCC 1:3:6, type C-1, (using 20mm graded crushed stone aggregates) masonry with solid blocks or slabs 10 cms thick (with plain or interlocking joints as directed) and setting in mortar 1:6, complete all as specified and directed.

M&L for walling of random rubble stone masonry, uncoursed, well bonded, bedded and solidly hearted, built in cement mortar 1:6, complete all as specified and directed.

M&L for walling of random rubble stone masonry, uncoursed, well bonded, bedded and solidly hearted, laid dry, complete all as specified and directed.

Extra over stone walling for hammer dressing for lime, sand stone, n.exc. 40mm deep when held against edge, complete all as specified and directed.

M&L for Plain cement concrete 1:3:6 type C-0 (using 12.5mm graded crushed stone aggregate), as in Damp Proof Course, complete all as specified and directed.

M&L for Form work to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and sofits (if any) of foundations and plinth beams and similar works, vertical or to batter, for rough finished surfaces of concrete, complete all as specified & directed by Engr-in-Charge.

M&L for Form work to sides and soffits of floor or roof beams, beam haunchings, girders, bresummers, lintels, cantilevers, shelves including supports, overhanging, etc. also splays between floors and beams etc., for rough finished surfaces of concrete, complete all as specified & directed by Engr-in-Charge.

M&L for Form work to edges of concrete flat in floors openings in concrete walls, floor and roof and sides of RCC/PCC bands in walls, horizontal or sloping and similar work n.exc. 20 cm wide for rough finished surfaces of concrete, complete all as specified & directed.

M&L for Plain cement concrete M-25, (using 20mm graded crushed stone aggregate), as in foundations including rafts, footings, foundation beams, plinth beams, bases for column etc., basement slab under reamed piles, complete all as specified and directed.

M&L for Plain cement concrete M-25, (using 20mm graded crushed stone aggregate), as in beams, cantilivers, bressummers, lintels over 1.5m span, complete all as specified and directed.

M&L for Plain cement concrete M-25, (using 20mm graded crushed stone aggregate), as in slab supported on walls, beams and columns in floors, roofs, landings, balconies, complete all as specified and directed.

M&L for Plain cement concrete 1:2:4, type B-1 (using 20mm graded crushed stone aggregate), as in roof kerbs or mud stops, lintels upto 1.5m clear span, cills, steps, seismic and other similar bands, plinth courses, string courses lacing courses, parapets and railings upto 60 cm in height, coping, kneelers, apex stones bed plates, kerbs including weathering, slightly rounded or chamfered angles and throating, complete all as specified and directed by Engr-in-Charge.

M&L for precast cement concrete 1:3:6, type C-1 (using 20mm graded crushed stone aggregate), as in window or door cills, lintels bressumers, steps quoin blocks, string courses, copings, kneelers, apex stones, pier caps, columns, posts boundary pillars, bed plates, pintle block, anchorage blocks, bonders (for stone walling), corbels, brackets, etc., (of any section indicated), with plain fair faces including chamfers, weatherings, throating etc and setting in mortar 1:4, complete all as specified and directed by Engr-in-Charge.

M&L for precast cement concrete 1:2:4, type B-1 (using 20 mm graded crushed stone aggregates) as in landings, cover slabs (for manholes etc), chullah hoods, chhajja, water trough, shelves and similar articles with plain faces, setting in CM 1:6, complete all as specified and directed by Engr-in-Charge.

M&L for Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and as directed by Engr-in-Charge.

All as per description of item Ser No 23.00 above, but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders, complete all as specified and as directed by Engr-in-Charge.

M&L for Mild steel Joist, channel, angle, I-section, tubular pipes etc as in posts including plates conforming to Fe-290 grade E-165, complete all as specified and as directed by Engr-in-Charge.

S&F mild steel framed work such as grills, gratings etc with ends of bars shouldered and /or rivited or forged in spikes, framed guard bars, barred iron doors, ladders, framed balusters walk ways, railings, frame work of water tanks and similar work confirming to Fe-290, Gde E-165, complete all as specified and as directed.

M&L rolled sections as in main and cross beams, hip and jack rafters, purlins where connected to common rafters and running rails and guides for sliding doors, fixed with angle cleats or other connecting plates conforming to Fe-290 grade E-165, complete all as specified and as directed by Engr-in-Charge.

M&L MS compound girders and stanchions, lattic girders aerial masts, staging for water tanks and the like including caps, bases, splices etc incl all lattice bars, stiffners, gusset plates etc and similar work conforming to Fe-290 grade E-165, complete all as specified and as directed by Engr-in-Charge.

S&F 0.63mm thick galvanised corrugated mild steel sheeting with two corrugations side lap, fixed with coach screws and washers in roofs, walls etc with grade of zinc coating 275, complete all as specified and directed.

M&L for sand filling under floors or in foundations including watering and consolidation, complete all as specified and directed by Engr-in-Charge.

M&L for Hard core of broken stone or boulders of gauge not exc 63 mm deposited ,spread and levelled in layer not exc 15 cm thick complete all as specified and directed by Engr-in-Charge.

M&L for 75mm thick Plain cement concrete (1:2:4), type B-1 (using 20mm graded crushed stone aggregate), as in plinth protection, finished even and smooth without using extra cement, complete all as specified and as directed by Engr-in-Charge.

M&L forming contraction (Dummy) joints, 50mm deep x 10mm wide for plinth protection and similar work, filled with sealing compound Grade 'A', complete all as specified and directed by Engr-in-Charge.

M&L for 75mm thick Plain cement concrete (1:3:6), type C-2 (using 40mm graded crushed stone aggregate), as in sub base of floors, finished even and fair without using extra cement, complete all as specified and as directed by Engr-in-Charge.

M&L for 25mm thick Plain cement concrete 1:2:4 type B-0 (using 12.5mm graded crushed stone aggregate), as in floors, finished even and fair without using extra cement, complete all as specified and directed by Engr-in-Charge.

M&L for Non skid ceramic coloured tiles 7-8mm thick (square/rectangular) , area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm as directed by EIC, as in floors etc, set and jointed in neat cement slurry and pointed with white or coloured cement mixed with pigment to match the shade of tiles over and including 15mm thick screed bed in cement mortar 1:6 complete all as specified and as directed by the Engineer-in-Charge. Shade/Colour of tile shall be approved by the GE.

M&L for Non skid ceramic coloured tiles 7-8mm thick (square/rectangular) , area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm as directed by EIC, as in floors etc, set and jointed in neat cement slurry and pointed with white or coloured cement mixed with pigment to match the shade of tiles over and including 15mm thick screed bed in cement mortar 1:6 complete all as specified and as directed by the Engineer-in-Charge. Shade/Colour of tile shall be approved by the GE.

M&L for Machine cut kota stone slab flooring 20-25mm thick, bedded and jointed in grey cement slurry and pointed with white or coloured cement mixed with pigment to match the shade of granite including grinding and polishing over and including 20 mm thick cement screed in cement mortar 1:6 complete all as specified and as directed by the Engineer-in-Charge. Shade/Colour shall be approved by the GE.

M&L for Glazed ceramic coloured tiles of size 300 mm x 200 mm/ 450mm x 350mm x 7 mm thick as on vertical surfaces , set and jointed in neat cement slurry and pointed with white or coloured cement mixed with pigment to match the shade of tile over and including 10 mm thick cement screed in cement mortar 1:4 complete all as specified and as directed by the Engineer-in-Charge. Shade/Colour of tile shall be approved by the GE.

S&F second class hardwood plain, solid, straight chowkhats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together on with glue pinned at joints, complete all as specified and directed by Engr-in-Charge.

S&F 35mm thick, 2nd class hard wood plain framed panelled shutters, (any number of panels) with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers, complete all as specified and directed by Engr-in-Charge.

S&F 35mm thick, 2nd class hard wood glazed and skelton shutters, open rebated and prepared to receive glass/guage etc (without sash bars) edges of framing plain, chamfered or rounded fitted with cut and mitred beads for securing wire mess etc of sizes of members of shutters as specified in SSR Part - I section 8, clause 8.24(a), fitted to chowkats, complete all as specified and directed by Engr-in-Charge.

S&F 30mm thick, 2nd class hard wood glazed and skelton shutters, open rebated and prepared to receive glass/guage etc (without sash bars) edges of framing plain, chamfered or rounded fitted with cut and mitred beads for securing wire mess etc of sizes of members of shutters as specified in SSR Part - I section 8, clause 8.24(a), fitted to chowkats, complete all as specified and directed by Engr-in-Charge.

S&F steel ventilator with top hung shutter including hinges, steel peg stay, complete all as specified and directed by Engr-in-Charge. Note : Glass will be measured and paid seperately.

S&F Sheet glass 3mm thick ordinalry quality and glazing with oil putty or wooden beads in square not exc 0.50 sqm in each pane complete all as specified and as directed by Engineer-In-Charge.

S&F mild steel work as in hold fasts and similar work confirming to Fe-290 or Gd E-165, complete all as specified and directed by Engr-in-Charge.

M&L for Plain cement concrete 1:3:6 type C-1 (using 20mm graded crushed stone aggregate), as in hold fasts, bed block and like, complete all as specified and directed.

Supply and fixing Aluminium anodised, barrel tower bolts of extruded Section, size 150mm long and fixed, complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing Aluminium anodised, barrel tower bolts of extruded Section, size 100mm long and fixed, complete all as specified and as directed by the Engineer-in-Charge.

S&F Extruded aluminium alloy handles, fabricated type, Anodised, size 150mm complete all as specified and as directed by the Engineer-in-Charge.

S&F Extruded aluminium alloy handles, fabricated type, Anodised, size 100mm complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing mild steel butt hinges, medium weight cold rolled 100 mm size complete all as specified and directed by the Engineer-in-Charge.

Supply and fixing mild steel butt hinges, medium weight cold rolled 75 mm size complete all as specified and directed by the Engineer-in-Charge.

Supply and fixing 300mm long aluminium alloy , anodised sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolt and sliding bolts of extruded section or cast aluminium alloy fixed complete all as specified and as directed by the Engineer-in-Charge.

S&F 300 mm, brass ordinary, rat tail rod pattern springs, including roller and roller plate, complete all as specified and directed by Engr-in-Charge.

M&L for treating wooden chowkhat surfaces of any description n.exc 10 cm in width or girth with black bituminus paint in two coats, complete all as specified and as directed by Engr-in-Charge.

M&L for preparing and treating small articles of builders hardware such as MS hold fasts, MS butt hinges etc, with two coats of synthetic enamel paint over a coat of primer when unconnected with other paintings or when painted in a different tint, complete all as specified and as directed by Engr-in-Charge.

M&L for Rendering 10 mm thick, on fair faces of brick or concrete surfaces, in cement mortar 1:6, finished even and smooth (without using extra cement), complete all as specified and directed.

M&L for Rendering 15 mm thick, on fair faces of brick or concrete surfaces, in cement mortar 1:4, finished even and smooth (without using extra cement), complete all as specified and directed.

M&L for raised pointing to random or polygonal rubble, uncoarsed block walling in cement mortar 1:4, complete all as specified and directed.

M&L for 2nd class soft wood clean sawn timber scantling fixed with nails, complete all as specified and directed by Engr-in-Charge.

M&L for 2nd calss soft wood, clean sawn as in beading for edges of ceiling, lining and wooden flooring fixed with nails exc 6 sqcm and not exc. 13 sqcm in section, complete all as specified and directed by Engr-in-Charge.

M&L for 2nd calss soft wood, clean sawn as in beading for edges of ceiling, lining and wooden flooring fixed with nails exc 13 sqcm and not exc. 25 sqcm in section, complete all as specified and directed by Engr-in-Charge.

M&L 9mm thick prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, medium density, fixed with nails to frame work in wall panelling, shelves/boarding, rebated or flat edged, complete all as specified and directed by Engr-in-Charge.

M&L 9mm thick prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, medium density, fixed with nails to frame work in ceiling, rebated or flat edged, complete all as specified and directed by Engr-in-Charge.

M&L for preparation of new or previously untreated wood or wood based surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint (ordinary tint) over a coat of pink primer, complete all as specified and directed by Engr-in-Charge.

M&L for Preparation of new plastered or unplastered surfaces of walls and applying two coats of cement based paint, complete all as specified and as directed by Engineer-In-Charge.

M&L for Preparation of new plastered or unplastered surfaces of walls and applying three coats of white wash, complete all as specified and as directed by Engineer-In-Charge.

M&L for Preparation of new steel surfaces of any description, over 10cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat or red oxide primer, complete all as specified and as directed by Engineer-In-Charge.

M&L for Preparation of new CGI sheets with mordant solution to receive painting including washing and cleaning and applying two coats of synthetic enamel paint in camoflaged pattern over a coat or red oxide primer, complete all as specified and as directed by Engineer-In-Charge.

S&F in repairs viterous China squatting pan Orissa pattern 580 x 440 mm white with integral foot rest (excluding flushing cistern and flush pipe) with front or back inlet pattern incl bedding with PCC 1:2:4, type B-I, (using 20 mm graded crushed stone aggregates), complete all as specified and directed by Engr-in-Charge.

S&F 10 litres capacity PVC valveless syphonic action type, flushing cistern (ISI marked), low level with inlet, ball valve, float, brackets 45cm long, PVC connection & flush pipe complete all as specified & directed by Engr-in-Charge.

S & F Vitreous China wash basin, white, flat back, size 630 x 450mm including traps, waste chain, plug and porcelain stopper including brackets, complete all as specified & directed by Engr-in-Charge.

S & F 32mm dia waste couppling of PTMT (half or full threaded) 45 grams, complete all as specified and directed by Engr-in-Charge.

S & F bottle trap for 32mm dia discharge pipe of PTMT having minimum water seal of 25mm (minimum weight 260gms), complete all as specified and directed by Engr-in-Charge.

S & F PVC(SWR) 'P' or 'S' trap of 125/110 mm bore complete all as specified and directed by Engr-in-Charge.

S&F 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints, laid in trenches or in floors/fixed in walls, complete all as specified and directed.

S&F 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints, laid in trenches, complete all as specified and directed.

S&F 110mm dia, PVC (SWR) bend equal, any radius, complete all as specified and directed.

S&F 110mm dia, PVC (SWR) vent cowl, complete all as specified and directed.

S&F PVC (SWR) floor trap, 75 mm outlet bore, plain with grating including jointing with solvent cement, complete all as specified and directed.

S&F grating round, 140mm size, PTMT (minimum weight 50 gms), complete all as specified and directed.

S&F Towel rail, 600mm long of PTMT (minimum weight 190 gms), fixed with and including chromium plated brass screws and wooden/plastic cleats, complete all as specified and directed.

S&F 15mm bore, PVC connection pipe 450mm long with PTMT nuts at both ends, complete all as specified and directed by Engr-in-Charge.

S & F chromium plated soap dish any type fixed to plugs with brass screws, complete all as specified and directed by Engr-in-Charge.

S&F 100mm dia, CI floor trap, plain with grating, including jointing to waste pipe fixed in cement concrete 1:2:4 type B-1(using 20mm graded crushed stone aggregates), complete all as specified and directed.

S&F stack clamp made out of 25mm x 5mm flat iron stays including bolt and nuts and securing ends of stays to walls or roof for 50mm bore piece, complete all as specified and directed.

S & F 15 mm bore pillar taps, Cast Copper alloy, with capstan heads, chromium plated, screwed down high pressure with or without lettered Hot or Cold with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and directed by Engr-in-Charge..

S & F 15 mm bore bib taps, Cast Copper alloy, fancy type, with crutch or butterfly handle, chromium plated, screwed down, screwed for iron pipe or for brass ferrule, complete all as specified and directed by Engr-in-Charge.

S & F 15 mm bore angle stop valves, fancy type, chromium plated, with long shank and cup, cast copper alloy, screwed down high pressure with crutch or butter fly handle screwed both ends for iron pipes, complete all as specified and directed by Engr-in-Charge.

S&F 20 mm dia polyproplyene random copolymer (PPR) (SDR 7.4, PN-16) 3 layer pipe, UV stabilized and antimicrobial fusion welded having thermal stability for hot and cold water supply including all PP-R plain and brass threaded polypropylene random fittings such as bends elbow, tee short length socket union check nuts nipple etc (female and male as required including testing complete all as per manufactures instructions and as directed by Engineer-in-charge.

All as per description of Ser item No. 92.00 above but for 25mm dia pipes, complete all as specified and directed by Engineer-in-charge.

S&F 32 mm dia polyproplyene random copolymer (PPR) (SDR 7.4 & SDR 11 UV) 3 layer pipe with and including SFMC fitting such as bends elbow, tee short length socket union check nuts nipple etc (female and male as required, confirming to IS-15801, complete suitable for hot/cold water supply line including testing complete all as per manufactures instructions and as directed by Engineer-in-charge.

S & F 32mm bore Gate valve, confirming to ISO 9001-2000, IS-15801, screwed down under high pressure with crutch or butter fly handle, screwed both ends for PP-R pipes or for union, complete all as specified and directed by Engr-in-Charge.

M&L for Cutting and inserting 'T' in existing pipe line upto 50-75mm dai pipe, making connection of PP-R distribution branch with PP-R main of 50-75mm sizes by providing and fixing tee including cutting and making fusion joint etc., complete all as specified and directed by Engr-in-Charge.

S & F 25mm bore stop cock, chromium plated, screw down under high pressure with crutch or butter fly handle, screwed both ends for iron pipe or brass ferrule, complete all as specified and directed by Engr-in-Charge.

S&F rotational moulded polyethylene water storage tank (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part - I of capacity 1000 litres including all accessories, all as specified and directed by Engr-in-Charge.

S&F rotational moulded polyethylene water storage tank (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part - I of capacity 500 litres including all accessories, all as specified and directed by Engr-in-Charge.

M&L for 75mm thick Plain cement concrete (1:4:8), type D-2 (using 40mm graded crushed stone aggregate), as in sub base of floors and pavings, finished even and fair without using extra cement, complete all as specified and as directed by Engr-in-Charge.

M&L for 100mm thick Plain cement concrete (1:4:8), type D-2 (using 40mm graded crushed stone aggregate), as in sub base of floors and pavings, finished even and fair without using extra cement, complete all as specified and as directed by Engr-in-Charge.

Sand filling (50 mm average thickness) under floors in foundations and for laying interlocking paver blocks including watering and consolidation complete all as specified and directed by Engr-in - charge.

Machine pressed precast concrete interlocking paver block any shape and size, polished with grey cement and pigment, confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade, complete all as specified and directed by Engr-in - charge.

M&L for dressed granite or trap stone kerb of roughly squared stones of size 20cm x 30cm, dressed so that the maximum depression from a straight edge held against the dressed surface shall not exceed 6mm for top and exposed surfaces of sides and 20mm for the rest of surfaces jointed in cement mortar 1:6 and struck flush (rate included for removal of old damaged kerb stones of any description), complete all as specified and directed by Engr-in - charge.

M&L for Chequered cement concrete tiles 30cm X 30cm X 25mm thick, set, pointed & jointed in neat cement slurry in floors polished with grey cement & pigments, layed over 20mm thick cement screed base in cement mortar (1:6) all as specified and directed by Engr-in - charge.

S&F salt glazed stoneware drain pipes, 150mm internal diameter, laid in trenches and jointed, complete all as specified and directed by Engr-in - charge.

M&L for concrete bed in PCC 1:3:6, type C-2 (using 40 mm graded crushed stone aggregates) to drain pipes of bore 150mm including packing under and haunching against the sides of pipe after they are laid and tested, complete all as specified and directed by Engr-in-Charge.

Supply only broken brick for loose filling of gauge 80 mm to 150 mm graded, complete all as specified and directed by Engr-in-Charge.

M&L for Point wiring for one light point or fan point controlled by one switch with 1.50 Sqmm with colour coding, PVC insulated, unsheathed, FRLS single core, multi-stranded, copper conductor cable, 1100 Volts fire resistance ISI, drawn in and including PVC casing and capping not less than 20mm dia with sunk PVC terminal box, fire resistance, ISI marked, fixed surfaces of walls and ceilings, terminated in and including rectangular PVC board for mounting fitting/ switches/ sockets and 1.50 Sqmm, copper conductor, multi-stranded, FRLS as earth continuity wire connected to earth terminal, including making good to disturbed surface as matching to existing descriptions/ specifications, complete all as specified and as directed.

All as per description of item Ser No. 109.00 above but for 5 Amp, 3 pin socket on same board, complete all as specified and as directed by Engr-in-Charge.

All as per description of item Ser No. 109.00 above but for 5 Amp, 3 pin socket on independent board, complete all as specified and as directed by Engr-in-Charge.

All as per description of item Ser No.109.00 above but with 2.50 Sqmm cable, for one 6 pin switch socket outlet 15 Amp, on independent board, complete all as specified and as directed by Engr-in-Charge.

All as per description of item Ser No.109.00 above but with 4 Sqmm cable, for one 3 pin switch socket outlet 15 Amp, on independent board and 2.5 Sqmm copper conductor multistranded FRLS as earth continuity wire, complete all as specified and as directed by Engr-in-Charge.

S&F switch socket outlet, 2 in 1, 5 pin, 5 Amp, 240 volts, flush type, complete all as specified and directed by Engr-in-Charge. Make : Anchor/Plaza/Havells/Philips.

S&F switch socket combination, piano flush button single pole one way, 2 in 1, 6 pin, 5/16 Amp, 240 volts, complete all as specified and directed by Engr-in-Charge. Make : Anchor/Plaza/Havells/Philips.

S&F Lamp holder, PVC/polycarbonate type with back plate suitable for batten fittings, complete all as specified and directed by Engr-in-Charge. Make : Anchor/Plaza/Havells/Philips.

S&F 9 Watt LED Bulb, complete all as specified and directed by Engr-in-Charge. Make : Syska/Havells/Philips.

S&F Switch piano, flush type, single pole, one way, 5 Amps, 240 volts, complete all as specified and as directed by Engineer-In-Charge. Make : Anchor/Plaza/Havells/Philips.

S&F Ceiling rose, surface bakelite 65 x 50 mm two or three terminals complete all as specified and directed by Engr-in-Charge. Make : Anchor/Plaza/Havells/Philips.

S&F 2'x2' Recess/Surface mounting LED Light fitting 36 Watt including seperate electronic driver & high brightness SMD LEDs ultra modern suitable for armstrong/grid/POP ceiling in MS housing with high brightness 4000K LEDs suitable for 230 volt 50 Hz, Diffused type optics 2' x 2' in size complete with all accessories internaly prewired and including connecting up with twon core twisted flexible copper conductor cable for suitable size complete. Make:Havells cat part No : ENDURASLIMPROPLUS2X2PLR28/26WLED840MOD or equivalent in Bajaj /Crompton / Philips/ Wipro/GE.

S&F LED light fitting incl LED tube light batten type 1 x 20 watt, 230 volt, 50 Hz, mounted on integrated sleek extruded polycarbonate LED channel with white accrylic cover, cool white colour bipin holder, connector block etc complete with all accessories, internally prewired and including connecting up with twin core twisted flexible copper conductor cable of suitable size, complete all as specified and directed by Engr-in-Charge. Make : Cat part No of Havells : REGALBATTENT8UPTO1X22WDSBSWH for batten & PHOTONULTRAE2.01213T8SSTL20WLED865SPC for lamp or equivalent of Bajaj/Philips/Syska.

S&F LED bulk head light fitting 1 x 10 watt, 230 volt, attractive wall/ceiling mounted, any type with white reflector complete with all accessories, prewired and including connecting up with twin core twisted flexible copper conductor cable, complete all as specified and directed by Engr-in-Charge. Make : Cat part No of Havells : RUGBYNEONFT10WLED860SSYMTOPC or equivalent of Bajaj/Philips/Syska.

S&F Sheet metal enclosures for distribution box for MCBs, Single pole and neutral, 12 ways, 240 Volts, with 200 Amps rated bus bar, double door with bus bar neutral link earth bar, DIN rail, blank plate incl fixing DB flush in wall and making good disturbed surfaces, complete all as specified and directed by Engr-in-Charge. Make : Legrand/Havells/L&T.

S&F Sheet metal enclosures for distribution box for MCBs, Single pole and neutral, 4 ways, 240 Volts, with 200 Amps rated bus bar, double door with bus bar neutral link earth bar, DIN rail, blank plate incl fixing DB flush in wall and making good disturbed surfaces, complete all as specified and directed by Engr-in-Charge. Make : Legrand/Havells/L&T.

S&F MCB, SPN, 40 Amps, 240 Volts, AC, complete all as specified and directed by Engr-in-Charge. Make : Legrand/Havells/L&T.

S&F MCB, single pole, 6 to 32 Amps, 50 Hz, 240 Volts, AC, made from moulded self-existing thermostat plastic and suitable 'C' curve, 10 KA breaking capacity and terminal box suitable for 1.5 to 6 sqmm cable complete conforming to IS 8828 of 1996, complete all as specified and directed.

S&F Exhaust fan AC, single phase, 230 volt of size 300mm sweep with louvers and shutters and connecting up including provision of cable from ceiling rose to connector of fan controlled by one way switch, complete all as specified and directed by Engr-in-Charge. Make : Orient/Usha/Havells/Khaitan

Supply, installation, testing and commitioning of 5 star rated storage type water heater (Geyser) of storage capacity 100 ltrs, verticle/horizontal type suitable for operation on 230 volts, 50 Hx, one phase AC supply with 3 KW automatic cutout, complete all as specified and directed by Engr-in-Charge. Make : Cat part No of Havells : GHWAMGSWH100 of equivelant make of Bajaj/Venus/V-Guard.

S&F LED light energy saving & environmental friendly, long life versatile pressure dia cast aluminium, IP66 street light of 48 watt, 5700K, 240 volts, single phase LED light suitable for 50mm dia pipe for fixing on wall incl connection with suitable size 3 core PVC cable, complete all as specified and directed. Make : Havells cat Part No ENDURAPEARLNEOSL48WLED757SASYTOPC of equivalent in Bajaj/Philips/C&G.

S&F LED light energy saving & environmental friendly, long life versatile pressure dia cst aluminium, IP66 street light of 30 watt, 5700K, 240 volts, single phase LED light suitable for 40mm dia pipe for fixing on wall incl connection with suitable size 3 core PVC cable, complete all as specified and directed. Make : Havells cat Part No ENDURAPEARLNEOSL48WLED757SASYTOPC of equivalent in Bajaj/Philips/C&G.

Supply and laying or fixing or passing through pipe, 1100 volts grade heavy duty cable with PVC insulated aluminium conductor served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheathed 10 sqmm nominal cross section, 2 core in service connections, complete all as specified and directed by Engr-in-Charge. Make : Plaza/Finolex/Havells/Gloster.

Supply and laying cable XLPE insulated PVC bedded steel strip or wire armoured, heavy duty electric power cable with aluminium conductor 1100 volts grade, 2 core, cross sectional area 10 Sqmm, complete all as specified and directed by Engr-in-Charge.

Sand cushioning to protection of underground cables, laid 8 Cm before laying and 15 Cm after laying of cable, and punned to form an overall layer of 18 Cm thick, complete all as specified and directed by Engr-in-Charge. Note: Punned thickness shall be measured.

Supplying and laying un-reinforced precast concrete cable cover, Class LV Type-I, flat, size 250mm x 150mm x 40mm, complete all as specified and directed by Engr-in-Charge.

M&L for Earthing complete with galvanized steel earth plate electrode 600x600x6 mm buried directly in ground (earth pit not less than 2.25mtr deep below GL) with top edge of earth plate not less than 1.5mtr below normal GL, connected with GI wire 4.0mm dia as earth lead means of bolts, nuts, check nuts and washers of GI or steel complete with 15 mm dia GI light grade protection pipe, 20mm dia GI light grade watering pipe with funnel incl charcoal, dust, salt, PCC M-15, type B-1 in pit with precast RCC M-15(1:2:4), type B-1(using 20mm graded crushed stone aggregates) in cover reinforced with 8mm dia TMT bars @ 75mm c/c both ways with mild steel handles of 12mm dia, PGI funnel with wire mesh incl, test point etc. all as shown in electric plate No-5 of SSR Part-I (2009), complete with necessary earth work in any type of soil, removal to a distance n.exc. 50mtr, incl testing on completion, complete all as specified and as directed. Note : Earth pit chamber and RCC pit cover shall be painted with two coats of sythentic enamel paint over one coat of primer. The cost of earth work, PCC pit and pit covers, funnel and watering pipe, wire mesh, charcoal dust and common salt, 15mm dia, light grade, GI pipe as protection to earth lead and earth lead as 4.0mm dia GI wire shall be deemed included in the unit rate for earthing.

Mehar Enterprises

HILL AND CO.