RequiredExperience with Government
RequiredAnnual Turnover
RequiredCertificate (Requested in ATC)
RequiredOEM Authorization Certificate
RequiredOEM Annual Turnover Bid to RA enabled Yes Track Suits - Sports ( 943 pieces ) Technical Specifications * As per GeM Category Specification Specification Specification Name Values Bid Requirement (Allowed Values) UTILITY UTILITY Unisex * COMPONENTS Components Complete Set consisting of Upper and Lower * MATERIAL Fabric ( Composition ) Polyester Polyester 1/9 Percentage of Blending ( in case of Blended Fabric ) Not Applicable Not Applicable Mass ( gram per square mtrs ) 140 * Fabric Construction Woven Woven Weave ( In case of Woven Fabric ) Plain Plain
RequiredDiamond
RequiredBox Weave
RequiredNot Applicable
RequiredAny other weave as per buyer's requirements Any other weave as per buyer's requirements ( in case weave is other than already mentioned above ) - * Knitting ( In case of knitted Fabric ) Not Applicable Not Applicable Ends per dm - * Picks per dm - * Courses per dm - * Wales per dm - * Count of knitting yarn - * Raising at inner side of Main Fabric No Yes
RequiredNo Upper Lining No Yes
RequiredNo Lower Lining No Yes
RequiredNo Lining Material 100% Polyester Mesh 100% Polyester Mesh Mass of Lining (Gram per Square Meter) 55 * Netting mesh No of holes on base & bias within 625 Square millimeter Not Applicable * Technical Requirements of Slide Fastener for Upper Closing Light Duty as per IS 14181 Latest Light Duty as per IS 14181 Latest
RequiredNo Technical Requirements of Slide Fastener for Pocket Closing ( For Pockets with Slide Fastner for closing ) Light Duty as per IS 14181 Latest Medium special duty Open End as per IS 14181 Latest
RequiredLight Duty as per IS 14181 Latest
RequiredNo
RequiredNot applicable Slide Fastners are BIS Marked Yes Yes
RequiredNo
RequiredNot Applicable Width of Tape Elastic at 3.5 cm * 2/9 Waist of Trouser Width of Tape Elastic at Bottom of Upper 3.5 cm * Technical Requirements of Waist Band Waist band as per IS 9686- 1980 latest Waist band as per IS 9686- 1980 latest
RequiredNo Waist Draw Cord Polypropylene Cord of 4mm dia * Draw Cord Ends Fused * Breaking Strength of Draw Cord 340 N minimum * Sleeve Ends ( Cuff ) Elastic Tape * Upper provided with Piping No Yes
RequiredNo Lower provided with Piping No Yes
RequiredNo Piping Fabric- Composition 100 percent Polyester * Piping Fabric- Any other material as per buyer's requirements ( Other than mentioned above ) - * Piping Fabric Mass ( gram per square mtrs ) Not Applicable Not Applicable Embroidery Thread Polyester Polyester SIZE Size Large (L) Small (S)
RequiredMedium (M)
RequiredLarge (L)
RequiredExtra Large (XL)
RequiredDouble Extra Large (XXL) DIMENSIONS OF UPPER Width Across Chest 25 mm below under arm 55.0 cm ( Large ) * Width Across Bottom Opening (relaxed) 48 cm ( Large ) * Length at front from top of collar to bottom 68 cm ( Large ) * Sleeve length (from center of back to bottom of sleeve 87 cm ( Large ) * Sleeve opening relaxed ( Cuff ) Width 9.2 * Front Neck Drop 8.75 * Back Neck Drop 1.076 * Length of Slide Fastener 66 cm( Large ) * 3/9 DIMENSIONS OF LOWER Side Seam Length 107 cm ( Large ) * Waist relaxed ( Width Across ) 45.5 cm ( Large ) * Waist stretched (Width Across ) 55 cm ( Large ) * Seat/Hip ( 15 cm below waist band) 55 cm ( Large ) * Thigh (at Crotch) ( Width Across ) 37 cm ( Large ) * Bottom Opening ( Width Across ) 21 * Front rise including waist band 29 cm ( Large ) * Back rise including waist band 39 cm ( Large ) * Length of Waist Tying Cord 155 * Bottom Fold (Hem) with full turn in(cm) 1.5 * POCKETS Number of Pockets (Upper) 2 Side Pockets 2 Side Pockets Size of Side Pockets- Upper ( Length X Width ) ( cm ) 18 X 20 cm * Size of Inside Pocket at Chest- Upper Not Applicable * Side Pocket opening - Upper 17.5 cm * Side Pocket Closure with Slide Fastener -Upper No No
RequiredNot Applicable Number of Pockets (Lower) 2 Side Pockets 2 Side Pockets Size of Side Pockets - Lower ( Length X Width ) ( cm ) 18 cm X 20 cm * Side Pocket Opening- Lower 17.5 * Pocket Closure with Slide Fastener - Lower All Pockets without Slide Fastener Side Pockets with Slide Fastener
RequiredBack Pockets with Slide Fastener
RequiredAll Pockets with Slide Fastener
RequiredAll Pockets without Slide Fastener Material of Pockets Main Basic Fabric * COLLAR Collar Type Stand and Fall Type
RequiredPolyester * Raw edges
Requiredif any shall be bound by overlock stitching Yes * Waist band stitching of Upper Stitched in three rows with chain stitch on the elastic * Sleeve Bottom (Cuff ) Stitching Stitched in three rows with chain stitch on the elastic * Waist band stitching of Lower Stitched in three rows with chain stitch on the elastic * Lining seams Not Applicable * Bartack Stitching ( Reinforcement Stitching ) at stress bearing areas Pocket opening
RequiredCentre of Waist Band Seam and bottom hem and other stress bearing areas * Tunnel at Waist Band for Lower Two holes stitched to allow the draw cord with insertion free movement * Stitches per dm ( min ) 36 * COLOUR/PRINT Colour Navy Blue * Multicolour Contrasting Pannels Any other colour as per buyer's requirements - * Sublimation Printing (for 100 % polyester only) Without Sublimation Print as per buyer's requirements
RequiredWithout Sublimation Print as per buyer's requirements - * Colourfastness to Light ( IS 2454 ) 5 * 5/9 Colourfastness to Washing ( IS/ISO 105-C10
RequiredTest- C (3)) Change in Colour- 4; Staining of Adjacent Fabric- 3-4 * Colourfastness to Rubbing ( IS 766 ) Dry- 4/Wet- 3 * Colourfastness to perspiration ( IS 971 ) 4 * Colour of Mesh Lining Same as colour of the base fabric Same as colour of the base fabric
RequiredAny other colour as per buyer's requirements Any other colour of Mesh Lining as per buyer's requirements - * Colourfastness to Washing ( IS/ISO 105-C10
RequiredTest- C (3))- Mesh Lining Change in Colour- 4; Staining of Adjacent Fabric- 3-4 * Colourfastness to perspiration ( IS 971 )- Mesh Lining 4 * Colour of Piping Material White * Any other colour as per buyer's requirements - * OTHER REQUIREMENTS Pilling Resistant [after 5 hours Test as per IS 10971 (Part 1)]
Requiredmin 4 * Dimensional stability to washing
RequiredShrinkage or Elongation Percentage
Requiredmax ( IS 2977 latest)
Requiredin lengthwise and widthwise direction 2 1
Required2
Required3 LOGO AND MARKING Logo/Totem Marking As per buyer's requirements As per buyer's requirements Type of Logo Printed Embroidery
RequiredPrinted Number of Logos on Upper Not Applicable 1
RequiredNot Applicable Number of Logos on Lower Not Applicable 1
RequiredNot Applicable Size
RequiredDesign and Location of Logo as per buyer's requirement - * TEST REPORT Availability of Test Report from designated AHSP Yes Yes 6/9 NABL/ILAC accredited or Central Government Lab to prove conformity of products to the specification Test Report No - * Test Report Date - * Name of the Lab - * Address of the Lab - * Test reports to be furnished to buyer on demand
Requiredif claimed to be available Yes * ADVANCE SAMPLE Agree to provide Advance Sample(s) for buyer's approval before commencement of supply Yes Yes * Bold specifications are the golden parameters. * Bidders may note that In respect of non-golden Parameters
Requiredthe specifications 'Values' chosen by Buyer will generally be preferred over 'Bid requirement ( allowed Values) by the Buyer.
