GE/WS/Token No-56 OF 2025-26

Amount

Labour only for attending day to day external/treated water supply complaints of all nature including grey water pipe leakage i.e leakage in water supply pipe lines , fitting/fixture, over flow of overhead tank, no water supply in supply tank/direct kitchen tap and grey water supply in various locations & taking out water from trenches during repair including note down the complaints in complaint register complete all as specified and as directed (Note:- Any material required for attending complaints shall be measured and paid separately under respective item herein after as 'Supply only').

Labour only for attending day to day electric supply complaints of day to day maintenance of existing LT Panels involving replacement of meterials including connecting electrical accessories / spares of water supply installation from 0830 hrs to 1730 hrs and electrical fitting & light, short circuits in pump house including Note down the complaints from various locations in complaints register and distribution to the trademen complete all as directed. (Note:- (i) Any meterial required for atteding complaints shall be measured & paid seperately under respective item here after as 'supply only') (ii) The suitable shift duites as deems fit shall be decision of the Engr-in-charge

Notes for Item No 1.01 & 1.02 :- (i) Any material required for attending complaints shall be measured & separately under respectvie items here - in- after. (ii) The complaints shall be attended and the defetcs shall be rectified by a team of matric qualified having minimum 03 years experienced electrician/Plumber as applicable assisted with adequate number of helpers as directed by Engineer-in-charge. (iii) The complaints shall be attended & defect shall be rectified within 08 hrs commencing from date and time of notifying the complaint failing which a penalty @ Rs 200/- per complaint per day (08 hrs) shall be levied upon/imposed on the contractor and recovery shall be made from contractor's dues. (iv) In case, after checking & attending the defect, it is not possible to rectify the defect within 08 hrs, the facts shall be brought to the notice of Engineer-in-charge by the contractor/his rep. If Engineer-in- charge is satisfied with contractors view, no recovery will be made. (v) While attending the complaint of water supply if earth work is required then the same shall be measured and paid seperately under appropriate item of Sch 'A' of BOQ. However, no extra payments shall be made for dewatering. (vi) Cutting of GI pipe in position and threading is also deemed to be included in the job rate (Fittings and fixtures will be measured and paid separetely under respective items of Sch as 'supply only'). (vii) All T&P required for attending the Complaints shall be provided by the contractor.)

(viii) The Pipe Fitter shall always be in possession of die set complete with cutters,Taps, Pipe wrench, Chain wrench, Caulking tools, complete set of spanners and ladders etc as required at site. (ix) The Electrician shall always in possession of all Electrician tools, LT Megger, Earth Tester, Multimeter, Crimpling tool, insulation tape, Hand gloves etc required at site. (x) Rate for taking down/out existing & fittings & fixtures and refixing to make it functional shall be into account. All the fitting & fixtures shall be measured and paid supply only in respective items of BOQ i.e. Ser Item No. 3 to 16, 17, 18.01 to 18.05, 24, 44 to 50 and 54 to 60. (xi) A BOO ordered for material procured by contractor and taken on charge through RV and complaint wise dockets will maintained and USR's duly vetted by AO GE (E/M) for procured materials issued for incorporation in work will be mentioned in BOO. BOO will concorn/approved by Accepting Officer in one time for complete materials to be consumed in work and if any balance quantity of material left with contractor the same will received back on credit USR's & kept on record.

Supply only following items of sizes as mentioned :-

PTMT stop cock 15 mm dia

PTMT stop cock 20 mm dia

PTMT stop cock 25 mm dia

Tank nipple 20 mm dia

Tank nipple 25 mm dia

Supply only GI Socket 'medium grade' ISI Marked superior / standard of a make of following sizes :-

15 mm bore

20mm bore

25mm bore

40mm bore

50mm bore

Supply only GI Elbow 'Medium grade', ISI Marked superior / standard of a make of following sizes : -

15 mm bore

20mm bore

25mm bore

40mm bore

50mm bore

Supply only GI Union 'Medium grade', ISI Marked superior / standard of a make of following sizes : -

15 mm bore

20 mm bore

25 mm bore

40 mm bore

50 mm bore

Supply only 'GI Nipple' of suitable length as required at site & ordered by EIC both end screwed 'Medium Grade', ISI marked superior / standard of a make of following sizes:

15 mm bore

20mm bore

25mm bore

40mm bore

50mm bore

Supply only GI Reducing socket 'medium grade' ISI marked superior / standard of a make of the following sizes :-

25 mm x 15 mm bore

20 mm x 15 mm bore

25 mm x 20 mm bore

25 mm x 32 mm bore

40 mm x 32 mm bore

50 mm x 40 mm bore

40 mm x 20 mm bore

40 mm x 25 mm bore

50 mm x 25 mm bore

Supply only GI Tee 'Medium grade' ISI Marked superior / standard of a make of following sizes : -

15mm x 15mm x 15mm

20 mm x 20 mm x 15 mm

20 mm x 20 mm x 20 mm

25 mm x 25 mm x 25 mm

25 mm x 25 mm x 15 mm

25 mm x 25 mm x 20 mm

32 mm x 32 mm x 32 mm

40 mm x 40 mm x 40 mm

40 mm x 40 mm x 20 mm

40 mm x 40 mm x 25 mm

50 mm x 50 mm x 50 mm

50 mm x 50 mm x 40 mm

50 mm x 50 mm x 25 mm

50 mm x 50 mm x 20 mm

Supply only GI Solid plug heavy duty ISI Marked superior / standard of a make of following sizes : -

15 mm bore

20 mm bore

25 mm bore

32 mm bore

40 mm bore

50 mm bore

Supply only PTMT float valve of sizes as under, with epoxy coated aluminium rod 250mm length and high density plastic ball of 150mm dia complete all as specified and as directed:-

15 mm bore

20 mm bore

25 mm bore

40 mm bore

50 mm bore

Supply only Gun metal gate valve, with iron wheel head screwed both ends for iron pipe as per IS-778 complete all as specified and as directed of following sizes:-

Supply only of following items:

lead pig bar

Spun Yarn

Supply only Nuts ,Bolts and Washers 25 to 150 mm long of 6 to 20 mm dia complete all as specified and as directed.

Supply only 3mm thick rubber gasket, complete all as specified and as directed.

Supply & Fixing rotational moulded Poly-ethylene ISI water storage tanks (cylindrical vertical with closed top) of cap 500 Ltrs hoisted and fixed in position at pump house building top complete all as specified.

Supply & Fixing rotational moulded Poly-ethylene ISI water storage tanks (cylindrical vertical with closed top) of cap 1000 Ltrs hoisted and fixed in position at pump house building top complete all as specified.

Testing of drinking water collected from local source (bore wells /shallow wells in the area of AGE(U) W/S No.II and submission of detailed test report to the office of Engineer-in-Charge. (i) Carrying out minimum essential testing of water as per IS 10500-2012 mandatory for chemical colour, odour, taste, turbidity, PH value, TDS total hardness, iron, chloride, fluoride and residual free chlorine and Bacteriological total coliform organisms per 100 ml (MPN) and E Coli in 100 ml) with specific recommendation regarding suitability of water for drinking purposes. (ii) Collection of water from different sources of water i.e. Sump, bore wells & shallow well in a sterilized bottle and testing in NABL Approved laboratory as mentioned in specification Note :- Rate Quoted shall also deemed to be included for the followings:- (i) Cost of sterilized bottle as required. (ii) To and fro transportation charges for collection of samples from source (sump, bore & shallow wells)

Excavation in trenches not exc 1.5 M wide and not exc 1.5 M in depth for pipe line, etc in soft/ loose soil getting out and levelling of bottom surface to required level all as specified and as directed.

Returning filling in, including spreading, leveling, watering and well ramming in layers not exc 25 cm thick complete all as specified and as directed.

Removing excavated material to a distance not exc 50 m and depositing where directed not exc 1.5 meters above the starting point complete all as specified and as directed.

Boring holes under road pavement by bocky manually/mechanically in any type of soil upto 200 mm bore. Complete all as specified and directed by Engineer-in-Charge.

Surface dressing of uneven surfaces of the natural ground, rough excavated surfaces and filled area where ordered shall be trimed to an even surface horizontal or slopping, by removing vegetation and by scrapping high patches and filling low patches with the scrapping soil to given an even and neat look to the site. depth of cutting not exceeding 15 cm. complete all as specified and directed by Engineer-in-Charge.

Supply only 15 mm bore Bib tap standard of PTMT any colour high pressure screwed for male/ female treaded, for UPVC pipe/GI pipe of size 15mm bore complete all as specified and directed

Labour work required for taking out suction pipe 80 mm to 200 mm bore from sump of any capacity, dismantling of foot valve screwed / flanged type, and relowering after refixing in position the same duly cleaned / minor repair if any required such as replacement of rubber gasket/ lifting bolts & nuts including making thread for the suction pipes off sizes etc complete all as required and as directed by Engineer-in-Charge.

Taking up old GI steel tubing of following sizes with connections from Trenches/floors/walls including cleaning for refixing or removal complete all as specified and as directed. Note :- (i) Excavation & earth work shall be measured & paid separetely.

Relaying/refixing only jointing and testing of old GI pipes including cleaning completely in trenches/walls/floors as directed for the following sizes :-

Supply & Laying of GI pipe 'medium grade' ISI mark including all fittings in old/new positions in trenches/wall/floor complete and making good the distributed surfaces as per existing as directed of following sizes. (Note:- Excavation and earth work will be measured and paid separately.)

Taking up CI/DI Pipe of following sizes including all fittings) with spigot and socketed ends and lead tyton joints including burning out lead joints and recovering lead and including cleaning for refixing or removal, making good disturbed surface complete all as specified and as directed. (Note:- (i) Excavation & earth work shall be measured & paid separetely. (ii) Layout plan for laying of DI pipe shall be given by EIC in writing. (iii) DI pipe whole quantity of tender shall be procured by contractor for payment in 1st RAR as material lying at site.

Relaying/refixing of pipe CI/DI pipes after cleaning from inside with suitable chemical and rodding all as directed by Engineer -in-charge of following sizes :-

Supply only 'stem' made out from SS (all as per sample) of sluice valve of size as under : -

Supply only 'stem nut' made out from stainless steel suitable to match with existing sluice valve of sizes as under : -

Supply only 'gland plate' made out CI, suitable to match with existing sluice valve of sizes as under : -

Material and labour for CI/DI specials any size like bends, tapers any type any radius and angle, Tee pieces single branch `Y' junction, double branch, cross (all sockets or socket and spigot) collars, DI connecting pieces one end flanged and other end spigot/socket, reducers/bell mouth pieces one end flanged and other end tapering as bell mouth

Supply, fixing, jointing & testing cast Iron Sluice Valve of following size ISI Marked, flanged ends drilled pressure rating PN-1.0, PD Short body, Confirming to IS 14846 -2000, having stainless steel spindle with cast iron operation wheel at top including taking out unserviceable sluice valve complete all as specified and as directed . (Note:- (i) Flanged joints complete with jointing material shall deemed to be included in the unit rate of this item.

80 mm dia

100 mm dia

150 mm dia

200 mm dia

250 mm dia

300 mm dia

Supply and Fixing in replacement of CI Foot valve of following size , Flanged ends, Swing type opration with rubber sheet as per IS-4038 including taking out unserviceable of following sizes complete all as specified and directed by Engineer-in-Charge. (Note :- (i) Flanged joints complete with jointing material shall deemed to be included in the unit rate of this items.

80 mm dia

100 mm dia

150 mm dia

Supply, fixing, jointing and testing of Cast iron Non Return valve without by pass arrangement, swing type, confirming to IS 5312, flanged ends pressure rating PN 1.0 complete including taking out unsv NRVcomplete all as specified and as directed at site by the Engr-in-Charge. Note:- Flanged joints complete with jointing material shall deemed to be included in the unit rate of this item.

80 mm dia

100 mm dia

150 mm dia

200 mm dia

Supplying, laying, jointing, welding & testing MS Pipe (Heavy duty class 'C') 8mm thick laid in trenches or on floors for connections to centrifugal pump sets for suction, pump to header and to connect out going water main CI/DI pipe line including taking down old unsv MS Pipe all as directed by Engr-in-Charge. Note:- (i) MS Flanges and Flange joints complete with jointing materials shall be measured and paid separately.

80 mm dia

100 mm dia

150 mm dia

200 mm dia

300 mm dia

Material and labour for PCC (1:3:6) type C-2 (using 40 mm graded stone aggregate) as in foundation of brick pillar to support the pipe line including demolition of old PCC and removing the debris from site complete all as specified and as directed at site by the Engr-in-Charge.

Material and labour for Brick work with sub class 'B' bricks straight or curved on plan exc. 6M mean radius built in CM (1:4) as in brick pillar of required size and shape to support the pipe line including demolition of old brickwork & removing from site all as specified and as directed at site by the Engr-in-Charge.

Supply and filling Multipurpose Grease lubricant for Motors & Pumps

Supply, fixing, jointing & testing butterfly valve (wafer type) of sizes as under, ISI Marked, flanged ends drilled pressure rating PN-1.0, PD Short body, inserting new one complete all as specified and as directed at site by the Engr-in-Charge.

100 mm dia

150 mm dia

200 mm dia

Supply, installation and testing flanged ends strainer/dirt box of following sizes with stainless steel mesh suitable for cold water meter to avoid foreign material entering into meter and making good connection with flanged ends, with gasket rubber sheet and nut & bolts fixing in horizontal/inclind/ vertical position, including taking out unsv strainer/dirt box complete all as directed at site by the Engr-in-Charge. Note :- Flange joints including jointing materials shall deemed to be included in the unit rate of this item.

100 mm dia

150 mm dia

200 mm dia

Supply, installation and testing of flanged ends water meter ISI marked woltman type, Class 'B' of following sizes and making good connection with flanged ends, with gasket rubber sheet and nut & bolts fixing in horizontal/inclind/vertical position, including taking out unsv water meter complete all as specified and directed at site by the Engr-in-Charge. Note :- Flange joints including jointing materials shall deemed to be included in the unit rate of this item.

80 mm dia

100 mm dia

150 mm dia

200 mm dia

M&L for 15mm thick cement plaster on fair faces of brick work or concrete surfaces in cement plaster 1:4 all as specified and direceted.

Supply & fixing HDPE pipes of pressure rating of 10Kg/CM square fixed complete to walls , ceiling, floor or in trenches any types of pipe including fittings & jointing to the existing of following sizes

75/80 mm dia

100/110 mm dia

150/160 mm dia

Supply & fixing Brass QCV(Quick coupling valve)/QRC(quick release valve) of size 1-1/4" (Make : Acutech/Neer/Nelson) complete all as specified and as directed

Supply & fixing Gear driven pop up sprinkler (full/part), 1'' inlet, capable dia 28 mtr to 50 mtr 2.8-6.9 bars with a discharge rate of 25.4 - 116 lpm complete all as specified and as directed

An amount of Rs 1,86,287.00 shall be deducted from BOQ on account of schedule of credit

Akarsha Enterprises (BID ID -3488724)

HSEDRIG ENGINEERS AND CONTRACTORS (BID ID -3494202)

PRASAD ELECTRICALS (BID ID -3495536)

Rahul Enterprises (BID ID -3489660)

airstack india (BID ID -3488507)

jain associates (BID ID -3489314)

M P TYAGI ENGINEERS AND CONTRACTORS (BID ID -3487263)