Loading…
Loading…
Tender Value
₹4.8 Cr
EMD Value
₹3.9 L
Closing Date
9 Jan 2026, 3:00 pmClosed
No
No
Single Packet System
Normal Tender
No
Not Applicable
Lowest to Highest
60 days
Expenditure
Capital (Works)
TRACK3
14 conditions · 2 needing a document upload
The tenderer must have minimum average annual contractual turnover of V/N or 'V' whichever is less; where V= Advertised value of the tender in crores of Rupees N= Number of years prescribed for completion of work for which bids have been invited. The average annual contractual turnover shall be calculated as an average of "total contractual payments" in the previous three financial years, as per the audited balance sheet. However, in case balance sheet of the previous year is yet to be prepared/ audited, the audited balance sheet of the fourth previous year shall be considered for calculating average annual contractual turnover. The tenderers shall submit requisite information as per Annexure-XIVA, of STD/June/22 along with copies of Audited Balance Sheets duly certified by the Chartered Accountant/ Certificate from Chartered Accountant duly supported by Audited Balance Sheet.
The tenderer must have successfully completed or substantially completed any of the following during last 07 (seven) years, ending last day of month previous to the one in which tender is invited: Three similar works each costing not less than the amount equal to 30% of advertised value of the tender, or Two similar works each costing not less than the amount equal to 40% of advertised value of the tender, or One similar work each costing not less than the amount equal to 60% of advertised value of the tender.
Defination of Similar Work :- Any steel structure fabrication works.
34 conditions · 8 needing a document upload
Check list should be as per the annexure-XXIII as given in the tender document attached. Note: Tenderer's attention is invited to clause 1 of Section VII and other relevant clauses of Section I and II whereby in case of nonsubmission/ non compliance, the tender offer is likely to be rejected.
1.1) Following documents are common for all types of firms i.e. Sole proprietorship, Partnership, Limited Company or JV.
(a)Tender Form (First Sheet) as per 'Annexure-I' (Mandatory)
(b) Firm details as per Annexure-II
(c)Format for Certificate as per proforma given in 'Annexure-III & III A' (Mandatory)
(d) List of works of similar nature physically completed in all respects in current and last three financial year as per proforma given in 'Annexure-IV'
(e)Work Completion Certificate of works mentioned in para (d) above from the Organizations with whom they worked as per proforma given in 'Annexure-V' as applicable. (Mandatory)
(f)List of works on hand as per proforma given in Annexure-VI
(g)List of plants & Machinery available on hand (own) and proposed to be inducted (own and hired to be given separately) for the subject work in Annexure-VII.
(h)List of Personnel, Organization available on hand and proposed to be engaged for the subject work in Annexure -VIII.
(i) The tenderer must have minimum average annual contractual turnover of V/N or 'V' whichever is less; where V= Advertised value of the tender in crores of Rupees N= Number of years prescribed for completion of work for which bids have been invited. The average annual contractual turnover shall be calculated as an average of "total contractual payments" in the previous three financial years, as per the audited balance sheet. However, in case balance sheet of the previous year is yet to be prepared/ audited, the audited balance sheet of the fourth previous year shall be considered for calculating average annual contractual turnover. The tenderers shall submit requisite information as per Annexure-XIVA, of STD/June/22 along with copies of Audited Balance Sheets duly certified by the Chartered Accountant/ Certificate from Chartered Accountant duly supported by Audited Balance Sheet.
(j)Self attested copy of Permanent Account Number (PAN) issued by Income Tax Department.
(k)The tenderer(s) are required to submit the test report of the stone ballast conforming to railways specifications as given in the condition no.7.2.2 of section-VI along with their offer, issued from the approved laboratory as listed in condition no 7.1.1(a) of section-VI in the tender documents. (This item will be applicable only for the tenders of supply of ballast).
(l)Any other document in support of his/their credentials/scheme.
(m)Contractual Receipt of the year on the Letter Head of Chartered /Cost accountant. 'Annexure-IX' (Mandatory)
1.2 In addition to Para 1.1 above certain more documents are to be submitted by tenderers as per status of their firms. These documents are listed below - (Mandatory)
1.2.1For Sole Proprietorship firm a)Affidavit as per 'Annexure - X'. b)Special power of Attorney as per proforma given in 'Annexure-XI' to be submitted by sole proprietor firm duly notarized.(Not required if tender documents are submitted by proprietor himself) (Mandatory)
1.2.2 For Partnership firm a)Self/Notary attested copies of Partnership deed. b)Special Power of Attorney as per proforma given in 'Annexure-XII' to be submitted by Partnership firm. (Not required if one or more partners are authorized in Parternership deed to sign on behalf of the firm.) (d)All other documents in terms of explanatory notes in clause 22 of STD/June/22
1.2.3 For Limited Company a) Copy of Memorandum & Articles of Association of Company. b)Self /Notary attested copy of resolution passed by Board of Directors authorizing its Director/Employee to deal with tender on behalf of company. c) 15.1.1 Attested copy of Notarized Special Power of Attorney including ratification clause duly signed by person authorized by the company vide (b) above as per proforma given in 'Annexure- XIII'. d) A copy of Certificate of Incorporation (Mandatory)
Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.
NOTE: BE IT KNOWN TO THE TENDERER THAT :-
All mandatory documents are required to be submitted by the bidder/tenderer at the time of bidding, in case of nonsubmission/ noncompliance, the tender offer is likely to be rejected.
(a)No post tender submission of documents shall be permitted in respect of item mentioned above. However, only clarification can be called for by Railway in respect of any part / document submitted by the tenderer which shall be responded to by the tenderer within 10 working days of the date of issue of such letter for clarifications, failing which the offer shall be dealt with as per available documents.
Rangiya Jn.-Majbat (SL)-TBCSR (H-Beam)-1279 Nos. under jurisdiction of DEN/III/RNY. (Project Id: 08.04.31.25.3.53.010)
94-ENGG-RNY-2025-26~NFR
94-ENGG-RNY-2025-26
Open
Works - General
12 Months
Kamrup, Assam
₹0
₹3.9 L
9 Jan 2026
18 Dec 2025
26 Dec 2025
35 items across 1 schedule · ₹6,33,91,769.83 total
| # | Description | Unit | Qty | Rate | Amount |
|---|---|---|---|---|---|
| 1 | Supplying fabricating and erecting welded and/or bolted and/or riveted steel work in built up sections, trusses and framed work, staging, racks, Height Gauge etc. for Steel Structures other than bridge girders, using RSJ, tees, angles and channels/flats, plates, gussets, round or square bars, cleats, bolts etc., with contractors own steel including cutting, bending, straightening, drilling, riveting, hoisting, fixing, erecting, welding, bolting etc., with Providing stiffeners wherever required as per approved drawing including applying a priming coat of a approved steel primer with all contractor's materials, labour, tools & plants, lead & lift including crossing of tracks if required etc., complete as per specification and as directed by Engineer-in- charge. Note: The payment shall be made on the theoretical weight of main components and gusset plates only. | MT | 39.65 | 1,38,571.69 | 54,94,367.51 |
| 2 | For location of work not involving deep screening | TRM | 210.00 | 186.69 | 39,204.9 |
| 3 | Locations other than Ballasted Deck Bridge | Each | 210.00 | 532.7 | 1,11,867 |
| 4 | Fish plates of 6 bolts. | Joint | 150.00 | 336.34 | 50,451 |
| 5 | Renewal of seized Plate/Rail screws on PSC Sleepers by using gas or any approved methods, duly drilling holes in broken screw and removing existing screw pieces from the holes along with existing dowels and fixing new contractor's dowels (procured from RDSO approved sources) and grouting around dowel with Epoxy materials of approved specification and refixing new Railway's rail/Plate screws duly greasing the screw with specified grease with all contractor's materials, consumables, tools & plants, labour with all lead, lift. Note: 1.Seized screws shall be identified and marked by JE/P.Way and verified at minimum SSE/P.Way In charge) level. 2. Due care shall be taken to avoid any damage to the sleeper 3.A penalty of 50% of the basic cost of new sleeper in nearest sleeper factory shall be levied on each, if sleeper gets damaged in the process. | Each | 500.00 | 350.08 | 1,75,040 |
| 6 | Rail section of 52Kg and above | Each | 350.00 | 142.98 | 50,043 |
| 7 | Boxing and profiling of ballast as per procedure prescribed in latest edition of IRPWM including cess dressing on both sides of track. The work will include removing excess ballast from track and putting the same in crib and shoulder by leading to a maximum of 50m including crossing of track, deweeding on ballast section etc and as directed by Engineer-In charge. | TRM | 4600.00 | 29.56 | 1,35,976 |
| 8 | For one shift ( 12 Hrs) | Each | 50.00 | 1,343.29 | 67,164.5 |
| 9 | For PSC Sleeper Track with Sleeper Density of 1660 | TRM | 4600.00 | 154.78 | 7,11,988 |
| 10 | For PSC Sleeper Track with Sleeper Density of 1660 | TRM | 4600.00 | 119.06 | 5,47,676 |
| 11 | Removing weeds & bushes in ballast section and cess up to 3.95m from centre line of track in mid section & station yard, as specified by Engineer in-charge including disposal of branches, bushes outside cess/yard. | TRM | 5000.00 | 16.74 | 83,700 |
| 12 | For 52 Kg Rails | TRM | 1500.00 | 95.99 | 1,43,985 |
| 13 | 52 Kg - 90 UTS - Outside Track | Each | 250.00 | 300.22 | 75,055 |
| 14 | On Running Line | Each | 1000.00 | 81.15 | 81,150 |
| 15 | Sleeper Spacing, Re-spacing / Squaring of sleeper by Hydraulic Sleeper Spacer with contractor's tools & plants, equipment, consumable with all lead & lift etc. complete, as directed by Engineer in-charge. Hydraulic Sleeper Spacer shall be as per RDSO's Specification No. TM/SM/17, dated 31.03.1992. | Each | 400.00 | 83.2 | 33,280 |
| 16 | Lead up to 5 Km | MT | 74.84 | 186.64 | 13,968.14 |
| 17 | Lead beyond 5 Km and up to 10 km | MT | 10.00 | 231.54 | 2,315.4 |
| 18 | Lead beyond 10 Km and up to 20 km | MT | 272.10 | 292.73 | 79,651.83 |
| 19 | Lead beyond 20 Km and up to 30 km | MT | 12.00 | 367.37 | 4,408.44 |
| 20 | Lead beyond 30 Km and up to 50 km | MT | 136.40 | 471.16 | 64,266.22 |
| 21 | Lead beyond 50 Km and up to 100 Km | MT | 100.00 | 697.45 | 69,745 |
| 22 | Rails, switches, crossings, SEJ, Glued Joints, Check Rails etc. | MT | 600.00 | 450.02 | 2,70,012 |
| 23 | Removing existing Channel/H-Beam sleepers with fittings from the running track under traffic block for TBTR & stacking the same neatly at specified places with contractor's tools & labour, as directed by Engineer in- charge. | Each | 1279.00 | 314.4 | 4,02,117.6 |
| 24 | Extra to item no. 192010 for Track Circuited area including handling of released PVC washers on bolts and extra rubber pads on sleepers | Each | 60.00 | 19.52 | 1,171.2 |
| 25 | Inserting in track Steel Channel/H-beam sleepers with all Railway supplied fittings complete for TBTR work to specified gauge under traffic block with contractor's tools including aligning, levelling to make track fit for 20 kmph speed and as directed by Engineer in-charge. Note: Transportation of track material if supplied beyond 250m of bridge approaches, shall be paid separately under relevant item. | Each | 1279.00 | 365.36 | 4,67,295.44 |
| 26 | Extra to item no. 192030 for Track Circuited area including handling of released PVC washers on bolts and extra rubber pads on sleepers. | Each | 60.00 | 37.26 | 2,235.6 |
| 27 | Providing and fixing of flared portion of guard rails of any rail section over PSC sleepers including fixing of with all fittings, including leading of rails and fittings, squaring and adjusting spacing of sleepers as required, providing nose blocks duly cutting wooden blocks supplied by railways and fixing it with bolts of 16mm dia as directed complete and finished as per RDSO's approved drawing. Note: 1.One set consists of LH & RH side rails of one end. 2.Required P.Way fittings will be supplied at SSE stores depot. | Set | 28.00 | 4,116.83 | 1,15,271.24 |
| 28 | Renewal of existing guard rails of all rail sections on bridge portion over wooden/PSC/steel channel sleepers excluding flared ends duly leading new guard rails including cutting of rails, drilling holes to the guard rails as required and as per drawings, refixing with all fastenings, and leading back the released rail, stacking at nominated place clear of infringements with all leads & lifts complete and as directed. | TRM | 28.00 | 260.73 | 7,300.44 |
| 29 | Dismantling of existing flared portion of guard rails of any rail section over PSC sleepers duly removing rails & fastenings and leading and stacking released materials at nominated place within free lead, clear of infringements, complete and as directed. Note: One set consists of LH & RH side rails of one end. | Set | 28.00 | 2,295.9 | 64,285.2 |
| 30 | Fabrication & supply of Galvanized H-beam Sleepers made out of the materials confirming to IS 2062 of standard Rolled sections as per approved drawing Nos RDSO/B/1636/4/R,5&9 complete and as directed by Engineer-in charge. Note: Cost of steel fittings and GRSP shall be paid separately. | MT | 230.00 | 1,57,973.64 | 3,63,33,937.2 |
| 31 | MS chequered plates 6 to 8mm thick including removal of existing chequered plates on Bridges. NOTE: Payment shall be made only as per weight of new Chequered Plate fixed. | Kg | 9010.00 | 117.84 | 10,61,738.4 |
| 32 | Supplying providing and fixing country kali wood/hard wood (Non teak) sleepers of various thickness and length as per the RDSO re railing ramp Drg No T-8259 for fixing bent rails and MS plates including cutting the wood in saw mills, transporting to site of work with all leads and lifts, labour, tools and plant etc. as directed by Engineer In-charge. | cudm | 1277.00 | 59.41 | 75,866.57 |
| 33 | Manufacture and supply of Hook Bolt 28mm dia. & 320mm long as per RDSO Drg. no. BA- 1636/I/R2 from RDSO approved sources | Kg | 25000.00 | 213.3 | 53,32,500 |
| 34 | Manufacture & supply of a set of 2 Nos of Elastomeric Pads 25mm / 30mm thick and 4 nos of Grooved rubber pads as per RDSO drawing No. B/1636/5 alt 2 to suit Insulated H Beam sleepers from RDSO approved sources with all contractor's material, lead, lift, labour, tools, plant and transportation etc. complete as per approved drawings and as instructed by Engineer in-charge. Note: One Set consists of 2 nos. Elastomeric Pad 25mm/30mm and 4 nos. Grooved Rubber Pad. | Set | 1400.00 | 2,242.12 | 31,38,968 |
| 35 | Supplying of Zero toe load fixtures for H Beam sleepers of 52/60Kg Rails procured from RDSO approved firms as per RDSO approved drawing with up-to-date correction slips and specifications with all contractor's lead, lift, labour, tools, plant, transportation etc. complete as per instructions of Engineer in- charge. Note: Complete fixture for 1 sleeper shall constitute 1 set. | Set | 1400.00 | 5,774.12 | 80,83,768 |
| Schedule total | ₹6,33,91,769.83 | ||||
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
HTML
nit.pdf
NIT
GCCACS10.pdf
ATTACHMENT
NITNo94-ENGG-RNY-2025-26_1.pdf
ATTACHMENT
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .