Renovation and Modification of Cafe Block and other remaining works at UT Bhawan, Chanakyapuri, New Delhi.

Items :

Providing & fixing of Fire Rated 40mm thick flush doors single leaf shutter made out of perimeter railing of Hard Wood as per fire rating specification of size 100mm x 22mm and infill of ceramic blanket (fire rated cloth) faced with 0.25mm thick face veneer & 2.5 mm thick 4 layers of core veneer. The fire Doors shall be as per IS: 5509-2000 with 60 minutes fire rating duly tested for Integrity & Insulation Criteria as per the IS 5509 with standard heating conditions as specified in IS:3809 - 1979 to achieve the required integrity & insulation (i.e. to restrict the heat radiation, temperature rise on the non-fire side to the maximum of 140 degree Centigrade above the ambient temperature on the unexposed surface of the shutter), with required cutting & modification works including fixing of 4 mm thick veneer of approved shade as per given drawings including melamine polish complete in all respect to the entire satisfaction of Engineer in- Charge. The rate also include door frame made of MR grade plywood with veneer finish and melamine polish complete in all respect. - Door shutter will be Fire rated with 60 minutes rating alongwith the test certificate. - Door Hardware shall be paid for separately . (Doors should be manufactured from NCBN "Non-combustible By Nature" Technology and confirm to National and International norms and standards like IS, BS, AS, ASTM and DIN in 60 minutes fire rating in

Providing & fixing of 40mm thick flush door made with water proof shutter with required cutting & modification works including fixing of 4 mm thick veneer of approved shade as per given drawings including melamine polish complete in all respect to the entire satisfaction of Engineer-in-Charge. The rate also include door frame made of MR grade plywood with veneer finish and melamine polish complete in all respect.

Providing and fixing of heavy duty 1 hour fire rated stainless steel 304 Butt Hinge (102 MM x 76 MM x 3 MM), 2,00,000 cycle tested, compliant to BS EN 1935, high corrosion resistance suitable for Fire rated doors with complete assembly offered by manufacturer etc, all complete with necessary screws as per specification and direction of Engineer-In-Charge. (Non-Fire Rated Door Hardware)

Providing and fixing of stainless steel concealed door closer fully compliant to EN 1154 and EN 1154:1996+A1:2002, having size EN3 (For Door width up to 950 MM) and cycle tested to 500,000 cycles with adjustable closing and latching speeds complete with necessary screws and accessories etc. complete in all respects to the entire satisfaction of Engineer-in Charge. finish: Silver

Providing and fixing of stainless steel Half Moon Floor Door Stopper with necessary screws and accessories etc. complete in all respects to the entire satisfaction of Engineer-in-Charge. Dimensions: 45 MM finish: Stainless Steel

Providing and fixing of Tubular Stainless Steel Lever Handle with necessary screws and accessories etc. complete in all respects to the entire satisfaction of Engineer-in-Charge. Lever on Rose Length: 135 MM finish: Satin Stainless Steel

Providing and fixing of Euro Mortise Lock with Back Set of 55 MM and center to center distance 72 MM with necessary screws and accessories etc. complete in all respects to the entire satisfaction of Engineer-in-Charge. finish: Satin Stainless Steel

Providing and fixing of 60 MM Euro Profile Cylinder lock with one side thumb turn & one side coin turn with necessary screws and accessories etc. complete in all respects to the entire satisfaction of Engineer-in-Charge. finish: Satin Nickle

Providing and fixing 12mm thk toughened glass including all the necessary hardware of Kitch or Ozone make as per the drawing and to the entire satisfaction of Engineer-in-Charge.

Providing and fixing stainless steel ( Grade 316) railing made of round Hollow tubes, channels, plates etc.,weight should be upto 17kg per running meter including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge.Providing and fixing stainless steel ( Grade 316) railing made of round Hollow tubes, channels, plates etc.,weight should be upto 17kg per running meter including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge.

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/Sq.mt including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Fixing glazed/ Ceramic/ Vitrified floor tiles with cement based high polymer modified quick-set tile adhesive (Water based) conforming to IS: 15477, in average 3mm thicknessDouble charge vitrified tile polished finish of size Size of Tile 600 x 1200 mm

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/Sq.mt including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily Glazed Vitrified tiles Matt/Antiskid finish of size Size of Tile 600 x 600 mm

Providing and laying Vitrified tiles in wall in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/Sq.mt including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily Fixing glazed/ Ceramic/ Vitrified floor tiles with cement based high polymer modified quick-set tile adhesive (Water based) conforming to IS: 15477, in average 3mm thicknessGlazed vitrified floor tiles polished finish of size Size of Tile 600 x 600 mm

Providing and fixing Glass mossaic tiles on finished plain wall surface of size 20 mm x 20 mm x 4 mm in all colour, design , fixing in customize design as per direction of Engineer-in- Charge. The glass mosaic tiles to be fixed on the wall surface with the help of approved adhesive applied at the rate of 2.5 kg per Sq.mt and grouting of the same. The rate is inclusive of all operation, material and required pattern approved by Engineer-in-Charge

Fixing glazed/ Ceramic/ Vitrified floor tiles with cement based high polymer modified quick-set tile adhesive (Water based) conforming to IS: 15477, in average 3mm thickness.

Providing and fixing foam based PVC sheet for protection of Vitrified Tile and any other type of flooring complete in all respects and to the entire satisfaction of Engineer-in-Charge.

Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size,approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement,mixed with matching pigment, epoxy touch ups, including rubbing, curing,moulding and polishing to edges to give high gloss finish etc. complete at all levels.

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying (a) First layer of slurry of cement @ 0.488 kg/Sq.mt mixed with water proofing cement compound @ 0.253 kg/ Sq.mt. This layer will be allowed to air cure for 4 hours.(b) Second layer of slurry of cement @ 0.242 kg/Sq.mt mixed with water proofing cement compound @ 0.126 kg/Sq.mt. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours.The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry

Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations:(a) Applying a slurry coat of neat cement using 2.75 kg/Sq.mt of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment.(b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineerin-charge over 20 mm thick layer of cement mortar of mix 1:5(1 cement :5 coarse sand ) admixed with water proofing compound conforming to IS : 2645 and approved by Engineerin-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs.(c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ Sq.mt of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge. (d)Finishing the surface with 20 mm thick jointless cement mortarof mix 1:4(1cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep.(e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test.“All above operations to be done in order and as directed and specified by the Engineer-in-Charge :With average thickness of 120 mm and minimum thickness at khurra as 65 mm

15 mm cement plaster on the rough side of single or half brick wall of mix: 1:4 (1 cement: 4 fine sand)

18 mm cement plaster in two coats under layer 12 mm thick cement plaster 1:5 (1 cement : 5 coarse sand) finished with a top layer 6 mm thick cement plaster 1:6 (1 cement : 6 fine sand).

Providing and applying 12 to 18 mm thick cement plaster on the rough side of brick work in cement mortar 1:5 (1 cement : 5 coarse sand) on external wall of height upto 16 Rmt including fixing GI chicken wire mesh or wire net 1 SWG, 75 mesh or equivalent, wherevr required with self tapping screws, sealing joints and all necessary accessories including mixing water-proofing material in cement plaster work in proportion as recommended by the manufacturer complete in all respects to the entire satisfaction of Engineer-in-Charge.

Providing and applying plaster of paris putty of 12 mm thickness over plastered surface to prepare the surface even and smooth complete

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete

Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications :Two or more coats applied on walls @ 1.25 ltr/10 Sq.mt over and including one coat of Special primer applied @ 0.75 ltr /10 Sq.mt

Finishing walls with Acrylic Smooth exterior paint of required shade New work (Two or more coat applied @ 1.67 ltr/10 Sq.mtover and including priming coat of exterior primer applied @ 2.20 kg/10 Sq.mt)

Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade Two or more coats on new work

Providing and applying Spectrum Parlina texture paint on Finishing wall with weather proof exterior grade emulsion of approved design (Apexultima) or its equarlied on decorated wall surfaces (two coats) to give an even shade and final finish after thoroughly cleaning the surface to remove all dirt, dust and other foreign matter etc. including sand paper smooth complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge.

Providing and fixing vinyl or Polyster Textile wallpaper coverings with approved adhesive on existing plastered surface finished with putty , to give bubble free uniform surface. Any unevenness of the base surface shall be removed before fixing the wallcovering, all complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge.

Providing and fixing (12.5 mm thick tapered edge gypsum moisture resistant board) false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/Sq.mt (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c,including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills,diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with: 12.5 mm thick tapered edge gypsum moisture resistant board.

Providing & Fixing with Dry Cladding work including labour,with all required Tools / Equipments with horizontal 6 mm groove with special aluminium developed profile (horizontal & vertical),clamps,ss 304 anchor fasteners,nut nolts etc.Complete as per Directed By Eng. In Charge

Providing and laying design mix cement concrete of M-30 grade, in roads/ taxi tracks/ runways, using cement content as per design mix, using coarse sand and graded stone aggregate of 40 mm nominal size in appropriate proportions as per approved & specified design criteria, providing dowel bars with sleeve/ tie bars wherever required, laying at site, spreading and compacting mechanically by using needle and surface vibrators, levelling to required slope/ camber,finishing with required texture, including steel form work with sturdy M.S. channel sections, curing, making provision for contraction/ expansion, construction & longitudinal joints (10 mm wide x 50 mm deep) by groove cutting machine, providing and filling joints with approved joint filler and sealants, complete all as per direction of Engineer-in-charge. Cement concrete manufactured in automatic batching plant (RMC plant) i/c transportation to site in transit mixer

Supply,checking, storing and fixing S. S. sink, single bowl with tap point on wall / counter comprising of Concealed type brackets fixed to wall with adjustable clamp to push against counter rim,40 mm heavy plated C.P. waste coupling JAQUAR-ALD-729 fitting without pop-up,with flexible PVC pipe with connector,CP swan neck sink faucet model JAQUAR-LYR-38347S Painting brackets with two coats of white enamel paint over one coat of primer,table mounted / wall mounted. Kitchen sink with drain board)(model :Nirali-olympia or equivalent)

Supply, checking, storing and fixing in position European water closet comprising of Wall hung European W.C. Pan Model ARIA-ARS-WHT-39951UFSM or Equivalent in white colour, on approved type of chairs,Concealed flushing cistern Model No.Geberit Omega Concealed Cistern with Flush plate or Equivalent or Equivalent as directed,C.P health faucet Model No. JAQUAR-ALD-565 or Equivalent with required length of flexible tube, clamp and bracket for fixing to wall,15 mm C.P. brass heavy quality angle stop cocks Model No.JAQUAR-JAQUAR-ALI-85053 or Equivalent for flushing cistern,C.P. brass 2-way bib cock Model No. JAQUAR-ALI-85041 or Equivalent,CP Toilet paper holder Model JAQUAR-ACN-1153S or Equivalent,Solid bakelite water closet cover and seat with C.P. hinges and rubber buffers,Fixing W.C. unit with brackets and accessories in position,Necessary pipe connection to PVC / PP / CI soil pipe,Painting bracket with two coats of white enamel paint over a coat of primer.

Supply, checking, storing and fixing Under Counter wash hand basin MODEL:JAQUAR-FNS-WHT-40701 ith ,32 mm heavy plated C.P. waste coupling JAQUAR-ALD-729 fitting with pop-up,32 mm heavy plated C.P. bottle trap JAQUAR-ALD-769L300X190 with cleaning eye with extension piece and wall flange,Painting brackets with two coats of white enamel paint over one coat of primer,CP Basin Mixture JAQUAR-ARC-87011B with 15 mm C.P. brass heavy grade flexible inlet connection with C.P. nut (minimum length 450 mm) made to measure.

Supply, checking, storing & fixing C.P. brass angle valve for basin & Sink MODEL:JAQUAR-ALI-85053, of approved quality conforming to IS:8931 for a) 15mm Nominal Bore

Supply, checking, storing & fixing C.P. brass bib cock MODEL:JAQUAR-ALI-85037 of approved quality conforming to IS:8931. a) 15mm Nominal Bore

Supply, checking, storing & fixing straight/offset type Macfit single body push fit type WC Pan Connector Jaquar-ZPS-WHT-VB01 with factory supplied spring loaded seal guard with integrated single mould sealing fins made of flexible EVA Body, including bush/adaptor for use with CI Pipe as supplied with Pan Connector (For European water closet)

Supply,Installation,testing and commissioning of Silent soil & waste pipes of PP(Polypropylene) material As per EN 12056 with Min. density 1.2 g/cm3 with mineral wool (for noise reduction) with push fit lock seal joints, with necessary fittings such as making proper connections to equipments including all necessary fittings and specials such as bends, tees, reducers,,Wye , Door tee , Vent cowl,Access pipe for claening in required interval(on service floor & basement) ,nuts,bolts,gaskets,supports and plugs etc. Fixing at wall/ ceiling level supported by clamps, fire collars,expansion joints,Y branches, hangers etc. as per the specification,drawings and schematics. All hangers, clamps, brackets,anchor/fixed support,guides,rollers etc. shall be of galvanized iron unless specified otherwise and then supply and installation of the same shall also be excluded for rates under this head. Welding of any kind on the galvanized support / hanger shall not be permitted.(The pipe length inserted in the fitting shall not be measured for payment) (Pipes for soil , waste for internal toilet). 40 mm

Supply,Installation,testing and commissioning of Silent soil & waste pipes of PP(Polypropylene) material As per EN 12056 with Min. density 1.2 g/cm3 with mineral wool (for noise reduction) with push fit lock seal joints, with necessary fittings such as making proper connections to equipments including all necessary fittings and specials such as bends, tees, reducers,,Wye , Door tee , Vent cowl,Access pipe for claening in required interval(on service floor & basement) ,nuts,bolts,gaskets,supports and plugs etc. Fixing at wall/ ceiling level supported by clamps, fire collars,expansion joints,Y branches, hangers etc. as per the specification,drawings and schematics. All hangers, clamps, brackets,anchor/fixed support,guides,rollers etc. shall be of galvanized iron unless specified otherwise and then supply and installation of the same shall also be excluded for rates under this head. Welding of any kind on the galvanized support / hanger shall not be permitted.(The pipe length inserted in the fitting shall not be measured for payment) (Pipes for soil , waste for internal toilet). 50 mm

Supply,Installation,testing and commissioning of Silent soil & waste pipes of PP(Polypropylene) material As per EN 12056 with Min. density 1.2 g/cm3 with mineral wool (for noise reduction) with push fit lock seal joints, with necessary fittings such as making proper connections to equipments including all necessary fittings and specials such as bends, tees, reducers,,Wye , Door tee , Vent cowl,Access pipe for claening in required interval(on service floor & basement) ,nuts,bolts,gaskets,supports and plugs etc. Fixing at wall/ ceiling level supported by clamps, fire collars,expansion joints,Y branches, hangers etc. as per the specification,drawings and schematics. All hangers, clamps, brackets,anchor/fixed support,guides,rollers etc. shall be of galvanized iron unless specified otherwise and then supply and installation of the same shall also be excluded for rates under this head. Welding of any kind on the galvanized support / hanger shall not be permitted.(The pipe length inserted in the fitting shall not be measured for payment) (Pipes for soil , waste for internal toilet). 75 mm

Supply,Installation,testing and commissioning of Silent soil & waste pipes of PP(Polypropylene) material As per EN 12056 with Min. density 1.2 g/cm3 with mineral wool (for noise reduction) with push fit lock seal joints, with necessary fittings such as making proper connections to equipments including all necessary fittings and specials such as bends, tees, reducers,,Wye , Door tee , Vent cowl,Access pipe for claening in required interval(on service floor & basement) ,nuts,bolts,gaskets,supports and plugs etc. Fixing at wall/ ceiling level supported by clamps, fire collars,expansion joints,Y branches, hangers etc. as per the specification,drawings and schematics. All hangers, clamps, brackets,anchor/fixed support,guides,rollers etc. shall be of galvanized iron unless specified otherwise and then supply and installation of the same shall also be excluded for rates under this head. Welding of any kind on the galvanized support / hanger shall not be permitted.(The pipe length inserted in the fitting shall not be measured for payment) (Pipes for soil , waste for internal toilet). 110 mm

Supply , installation , testing and commissioning Polyproplene (PP) 110mm x 110mm size P trap (Floor trap) of self cleaning design with Min. 50mm water seal with and without vent arm jointing with push fit rubber ring socket fittings complete, cutting chases / hole in floors / slabs and bringing the same in proper condition and shape after placing the trap in right position in case of suspended / open plumbing or setting the trap in 1:2:4 CC in case of concealed plumbing , etc. complete, as required. The trap shall be of following sizes: Temporary airtight PVC cover to be provided to prevent dirt entry.

Supply , installation , testing and commissioning Polyproplene (PP) 110mm x 75mm size Multi floor trap of self cleaning design with Min. 50mm water seal with and without vent arm jointing with push fit rubber ring socket fittings complete, cutting chases / hole in floors / slabs and bringing the same in proper condition and shape after placing the trap in right position in case of suspended / open plumbing or setting the trap in 1:2:4 CC in case of concealed plumbing , etc. complete, as required. The trap shall be of following sizes: Temporary airtight PVC cover to be provided to prevent dirt entry. ( In sahft )

Supply , installation , testing and commissioning rain water Sidewall Parapet CI Body With Aluminium Grate With 4 SS Screw Drains ,size as per drawing required depth with Making Khurra with Proper water proofing and fixing the fittings (Horizontel/vertical arrangment grating) complete as required.450x 450 mm (100mm outlet pipe dia )

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. For Cold Water Lines ( Domestic & Hot) (Inside Toilet)(Make:Astral,Ashirwad,Finolex) 15 mm nominal outer dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. For Cold Water Lines ( Domestic & Hot) (Inside Toilet)(Make:Astral,Ashirwad,Finolex) 20 mm nominal outer dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. For Cold Water Lines ( Domestic & Hot) (Inside Toilet)(Make:Astral,Ashirwad,Finolex) 25 mm nominal outer dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. For Cold Water Lines ( Domestic & Hot) (Inside Toilet)(Make:Astral,Ashirwad,Finolex) 32 mm nominal outer dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. For Cold Water Lines ( Domestic & Hot ) (In shaft & Terrace & Exposed On wall) (Make:Astral,Ashirwad,Finolex) 25 mm nominal outer dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. For Cold Water Lines ( Domestic & Hot ) (In shaft & Terrace & Exposed On wall) (Make:Astral,Ashirwad,Finolex) 32 mm nominal outer dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. For Cold Water Lines ( Domestic & Hot ) (In shaft & Terrace & Exposed On wall) (Make:Astral,Ashirwad,Finolex) 40 mm nominal outer dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge.65 mm nominal dia Pipes

Providing and fixing gun metal non- return valve of approved quality (screwed end) :25 mm nominal bore Horizontal

Providing and fixing forged brass lever operated ball valve of full flow with forged brass ball (Machined to mirror smooth finsh with hard chrome plated) and spindle with setting and gland of superior quality having minimum working pressure of 16 kg/cm2 etc. complete in all respect.(Make:Sant,Zoloto,leader) 20 mm dia

Providing and fixing forged brass lever operated ball valve of full flow with forged brass ball (Machined to mirror smooth finsh with hard chrome plated) and spindle with setting and gland of superior quality having minimum working pressure of 16 kg/cm2 etc. complete in all respect.(Make:Sant,Zoloto,leader) 25mm dia

Providing and fixing forged brass lever operated ball valve of full flow with forged brass ball (Machined to mirror smooth finsh with hard chrome plated) and spindle with setting and gland of superior quality having minimum working pressure of 16 kg/cm2 etc. complete in all respect.(Make:Sant,Zoloto,leader) 40mm dia

Supplying, fixing, testing and commissioning of following valves, gauges and strainers for condenser water circulation as per specifications.(Make:Sant,Zoloto,leader) BUTTERFLY VALVE (MANUAL) with C I body SS disc nitrile sheet & O - ring & PN 16 pressure rating as specified.65 mm dia.

Providing and fixing Y - STRAINER of Ductile CI Body flanged ends with stainless steel strainer for cold / hot water circulation including insulation as specified.(Make:Sant,Zoloto,leader) 65 mm dia.

Providing and laying Non Pressure NP-3 class (Medium duty) R.C.C. pipes including collars/spigot jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete 450 mm dia RCC pipes

Providing, laying, jointing and testing heavy quality DWC (Double wall Corrugated ) under ground application pipes for Sewer and strom line with Snap-Fit Coupler with Rubber Ring / In-line Socket Molded Coupler / Socket-Spigot Arrangement fittings of SN8 class of approved make laid to required alignment and slope trenches inclusive of excavation in all soil types, bailing or pumping out water from trenches, shoring, whenever necessary testing, refilling, in layers, ramming & consolidation, removing away the surplus earth & spoils, dumping it on site or carting away to lead of 100 meters as directed incl. 150 mm dia

Providing, laying, jointing and testing heavy quality DWC (Double wall Corrugated ) under ground application pipes for Sewer and strom line with Snap-Fit Coupler with Rubber Ring / In-line Socket Molded Coupler / Socket-Spigot Arrangement fittings of SN8 class of approved make laid to required alignment and slope trenches inclusive of excavation in all soil types, bailing or pumping out water from trenches, shoring, whenever necessary testing, refilling, in layers, ramming & consolidation, removing away the surplus earth & spoils, dumping it on site or carting away to lead of 100 meters as directed incl. 200 mm dia

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) up to haunches of S.W. pipes /UPVC /DWC Pipes including bed concrete as per standard design b)150 mm dia diameter

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) up to haunches of S.W. pipes /UPVC /DWC Pipes including bed concrete as per standard design c) 200mm dia diameter

Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design: 150 x 100 mm size P type With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone- III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand (zone- III) : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design : Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Inside size 120x90 cm and 90 cm deep including C.I. cover with frame (medium duty) 500 mm internal diameter, total weight of cover and frame to be not less than 116 kg (weight of cover 58 kg and weight of frame 58 kg) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS : 10910, on 12 mm dia steel bar conforming to IS: 1786, having minimum cross section as 23 mmx25 mm and over all minimum length 263 mm and width as 165 mm with minimum 112 mm space between protruded legs having 2 mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and having manufacture’s permanent identification mark to be visible even after fixing, including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) complete as per design.

Constructing brick masonry road gully chamber 50x45x60 cm with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) including 500x450 mm pre-cast R.C.C. horizontal grating with frame complete as per standard design : with common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Constructing brick masonry chamber for underground C.I. inspection chamber and bends with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg), R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 Fine sand : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand), finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design: Inside dimensions 455x610 mm and 45 cm deep for single pipe line : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Inside dimensions 600x 850 mm and 45 cm deep for pipe line with three or more inlets : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing and fixing high density polyethylene water storage loft tank with cover, conforming to ISI : 12701, colour of opaque white or as approved by Engineer-in-charge. The rate includes making necessary holes for inlet, outlet & over flow pipes. The base support i/c fittings & fixtures for tank shall be paid separately.

Supply, installation, testing & commissioning of Submersible single stage single entry pumps connected to submersible motor (The motor shall be IE3 watertight according to IEC class IP 68, and incorporate class F, insulation materials to withstand a continuous operating temperature of 155 deg C) for 415 + 10% volts, 3 phase, 50 cycles A.C. power supply with mechanical seal, pump connector unit Or Auto Coupling with rubber diaphragm and bend, vertical discharge pipe,Outdoor type Control panel, pumps at high level with cut off at dry level as determined. The pump shall be provided with a lifting devise of pull chain/guide rail & G.I. heavy class rising main of 5m length including interconnecting piping, valves (Ball Valve / Butterfly), Non return valves (GM/CI) 15 m cable etc.High level and low level sensor with motorized butterfly valve as per requirement complete in all respects. (Pumps shall be installed in a set of two pumps One working and One standby, with cascade operation). For supplying Domestic Water up to terrace Capacity per pump - 180 LPM Head - 30 mtr 1 Set = 2 Nos. Pump (1 Working + 1 Standby - cascade operation) Suction head - flooded positive suction Supply, Installation, testing & commissioning (Make:Kriloskar,Lubi)

Supplying, Erecting, Testing & Commissioning the passenger / stretcher lift having following main features: 8 / 10 Passengers, Ground plus 2 upper floor with Rated Speed of 1.0 m/sec. (C) With General PLUS ADDITIONAL SPECIAL FEATURES attached herewith. Prem.

Supplying and fixing single headed hydrant valve with instantaneous Gunmetal/Stainless Steel coupling of 63mm dia with cast iron wheel ISI marked conforming to IS 5290 (Type-A) with blank Gunmetal/Stainless Steel cap and chain as required: Single headed Stainless steel.

Supplying and fixing of 750 mm x 600 mm x 250 mm Outdoor application Fire Hose Cabinet made of 1.6 mm thick MS sheet Duly powder coated in red color externally and white internally with 6 mm thick glazed doors with suitable to accommodate 2 Nos 15 Mtr. Long RRL Hose and 1 No. branch pipe on Existing Wall / Angle Iron Frame as required.

Supplying and fixing of 1000 mm x 600 mm x 500 mm Outdoor application Fire Hose Cabinet made of 1.6 mm thick MS sheet Duly powder coated in red color externally and white internally with 6 mm thick glazed doors suitable to accommodate External hydrant with butterfly valve, 2 Nos 15 Mtr. Long RRL Hose and 1 No. branch pipe on Existing Wall / Angle Iron Frame as required.

Supplying and fixing of fire brigade connection of cost iron body with gun metal instantaneous inlet coupling complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required: 2 way-100 mm dia M.S. Pipe.

Supplying and fixing of fire brigade connection of cost iron body with gun metal instantaneous inlet coupling complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required: 4 way-150 mm dia M.S. Pipe.

Providing and fixing of 100 mm Dia. Flanged Gun Metal Fire brigade Suction hose coupling (draw out connection) for female coupling as per IS:902- 1974 complete with Matching Flange (Minimum 14 mm thick), nuts, bolts, washers, gaskets, etc as required.

Supplying and fixing 63mm dia, 15m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required: Stainless Steel (Grade 304)

Supplying & fixing SS-304 Short Branch Pipe conforming to IS: 903:93 fitted with 20mm (nominal internal diameter) bore nozzle.

Providing & fixing of pressure switch in M.S. pipe line including connection etc. as required.

Supplying and fixing first -Aid Fire hose reel Drum wall mounted swinging type with MS construction powder painted in post office Red, conforming to IS 884-1985 through Forged steel Screwed Union & M.S. pipe. Etc.

Providing, laying, testing & commissioning of 'C' class Heavy duty M.S. pipe conforming to IS 3589/IS 1239 including welding, fitting like elbows, tees, flanges, tapers, nuts, bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required: 25 mm dia

Providing, laying, testing & commissioning of 'C' class Heavy duty M.S. pipe conforming to IS 3589/IS 1239 including welding, fitting like elbows, tees, flanges, tapers, nuts, bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required: 32 mm dia

Providing, laying, testing & commissioning of 'C' class Heavy duty M.S. pipe conforming to IS 3589/IS 1239 including welding, fitting like elbows, tees, flanges, tapers, nuts, bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required: 40 mm dia

Providing, laying, testing & commissioning of 'C' class Heavy duty M.S. pipe conforming to IS 3589/IS 1239 including welding, fitting like elbows, tees, flanges, tapers, nuts, bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required: 50 mm dia

Providing, laying, testing & commissioning of 'C' class Heavy duty M.S. pipe conforming to IS 3589/IS 1239 including welding, fitting like elbows, tees, flanges, tapers, nuts, bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required: 80 mm dia

Providing, laying, testing & commissioning of 'C' class Heavy duty M.S. pipe conforming to IS 3589/IS 1239 including welding, fitting like elbows, tees, flanges, tapers, nuts, bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required: 100 mm dia

Providing, laying, testing & commissioning of 'C' class Heavy duty M.S. pipe conforming to IS 3589/IS 1239 including welding, fitting like elbows, tees, flanges, tapers, nuts, bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required: 150 mm dia

Supplying and Fixing of PN 16 Cast Iron Type Gate Valve complete with 2 no. Matching Flanges (Minimum 16 mm thick), nuts, bolts, washers, gaskets, etc as required of following sizes. 100mm dia

Supplying and Fixing of PN 16 Cast Iron Type Gate Valve complete with 2 no. Matching Flanges (Minimum 16 mm thick), nuts, bolts, washers, gaskets, etc as required of following sizes. 150mm dia

Supplying and Fixing of PN 16 Cast Iron Type Gate Valve complete with 2 no. Matching Flanges (Minimum 16 mm thick), nuts, bolts, washers, gaskets, etc as required of following sizes. 200mm dia

Supplying, fixing, testing and commissioning of butterfly valve PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required: 80 mm dia

Supplying, fixing, testing and commissioning of butterfly valve PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required: 100 mm dia

Supplying, fixing, testing and commissioning of butterfly valve PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required: 150 mm dia

Supplying and Fixing of PN 16 Brass/GM Ball valves with screwed end, SS Ball including teflon tape etc. as required. 25 mm dia.

Supplying and Fixing of PN 16 Brass/GM Ball valves with screwed end, SS Ball including teflon tape etc. as required. 50 mm dia.

PUMP: (A) Repair, installation, testing and commissioning of Electric driven Main Fire Pump suitable for automatic operation and consisting of following, complete in all respects, as required: (B): Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical seal conforming to is 1520. (C) Suitable HP squirrel cage induction motor, TEFC, synchronous speed 1500 RPM, suitable for operation on 415 volts, 3 phase 50 Hz, AC supply with IP 55 protection for enclosure, horizontal foor mounted type with Class-'F' insulation, conforming ti IS-325. (D) M.S. fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required. (E) Suitable cement concrete foundation duly plastered with anti vibration pads. 2280 Ipm at 70 m Head

PUMP: (A) Repair, installation, testing and commissioning of diesel engine driven main fire Pump suitable for automatic operation and consisting of following, complete in all respects, as required:(Diesel Driven Pump) (B): Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical seal conforming to is 1520. (C) Suitable HP , 1500 RPM water cooled with radiator, diesel engine conforming to relevant IS standard complete with auto starting mechanism, 12/24 volts electric starting equipment, diesel tank, exhaust pipe extended upto 10 m outside pump house duly insulated with 50 mm thick glass wool with 1.0 mm thick aluminium sheet cladding, residential silencer, instruments and protection as per standard specification, stop solenoid for auto stop in the event of fault with audio indications, painted with post office red colour etc. as required. (D) M.S. fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required. (E) Suitable cement concrete foundation duly plastered with anti vibration pads. 2280 Ipm at 70 m Head

PUMP: (A) Repair, installation, testing and commissioning of electric driven pressurisation Pump suitable for automatic operation and consisting of following, complete in all respects, as required:(Jockey Pump) (B): Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical seal conforming to IS :1520. (C) Suitable HP squirell cage induction motor TEFC type suitable for opertaion on 415 volts, 3 phase 50 Hz AC supply with IP 55 class of protection for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS:324. (D) M.S. fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required. (E) Suitable cement concrete foundation duly plastered with anti vibration pads. 180 Ipm at 70 m Head

Supplying and Fixing of Air vessale 250X1200 mm etc. as required.

Supplying and Fixing Cable & Cable tray tc. as required.

Supplying, installation, testing & commissioning of intelligent analog addressable photothermal detector complete with mounting base complete as required

Supplying, installation, testing & commissioning of response indicator on surface/recessed MS Box having two LED, metallic cover complete with all connections etc as required

Supplying, installation, testing & commissioning of addressable manual call point complete as required

Supplying, installation, testing & commissioning of fault isolator complete with base as required

Supplying, installation, testing & commissioning of addressable fire control module complete as required

Supplying, installation, testing & commissioning of addressable phone control module complete as required

Supplying, installation, testing & commissioning of addressable strobe complete as required

Supplying, installation, testing & commissioning of central graphical fire alarm management system to centrally monitor and operate the fire alarm system complete as required.

Supply , Installation , Testing and Commissioning of Addressable Fire Fighter's Telephone Jack with suitable module for two way communication between Remote Fire Fighter & Fire Command Center

Supply , Installation , Testing and Commissioning of Fire Fighter's Telephone Handset for two way communication between Remote Fire Fighter & Fire Command Center.

Supplying & laying of 2x1.5 Sq.mtm fire alarm armoured cable, 600/1000V rated with annealed copper conductor having XLPE insulation, steel wire armouring & FRLS outer sheath complete as required

Supplying, Erecting, Testing & Commissioning Heritage Lighting fixture & 7.5/8 mtr Pole made of Galvanized mild steel tubes having polyurethane paint with decorative cast alum embellishments & cast aluminum ornamental design base including 1x90 watt designer LED fixture IRIS-N Made of spun aluminum with power LEDS & aluminum heat sinks. Fixtures are mounted on Ornamental designer drop down Single arm bracket made of mild steel & aluminum. Poles havong service window at bottom containing 6-amp MCB& 4WAY connector.

Shan Enterprises