PROVN OF CHAIN LINK FENCE AND GATE 800M FOR IAG SNIPER FG COMPETITION AT BARGONDA FD FG RG AT INF SCHOOL AND CERTAIN REVENUE AND MINOR WORKS AT BARGONDA FD FG RG AT INF SCHOOL MHOW

Amount

Surface excavation not exceeding 30cm deep and averaging 15cm deep and getting out in hard/Dense soil, complete all as specified.

Excavation in trenches n.exc 1.5m wide and n.exc 1.5m in depth for foundation, shafts, wells, cespits, manholes pier hole etc n.exc 10 Sqm on plan and getting out in hard/Dense soil, complete all as specified.

Returing, filling in trenches, including spreading, levelling, watering and well ramming in layers not exc 25 Cm in hard/dense soil complete all as specified.

Removing excavated material (soil) to a distance not. exc. 50m and depositing where directed at a level nexc 1.5m above the starting point.

Excavating post holes or similar holes, each not exceeding 0.5cum and getting out in Soft/ Loose soil including returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, watering, and removing surplus soil to a distance n.exc 50m & making good surface complete all as specified.

M & L for PCC 1:2:4 type B2 using 40 mm graded aggregate as in foundation ,post, etc complete all as specified.

M&L for PCC 1:2:4 type B0 using 12.5 mm graded stone aggregate as in sub base, levelling course, etc complete all as specified.

M&L for PCC1:4:8 type D2 using 40mm graded stone aggregate as in foundation, filling, mass concrete and sub base of floor, etc complete all as specified.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc including provision of binding wire complete all as specified.

Supply only Chain link MS galvanisd fencing of any size or type complete all as specified and directed by Engineer in Charge.

S & F 11 to 15mm dia of neck MS Screw bolts(Machine made ) with hexagonal or square heads at one end and screwed at other end or both end, and screwed end to be fitted with washer and one hexagonal or square n.exc 20 cm long complete all as specified.

S&F mild steel Joist, channel, angle,flat or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated) conforming IS-1161-1979 grade ST-240 complete all as specified.

S & F Mild Steel framed work as in doors or gates of angle iron, door frame or other section with gusset plate, rails, braces etc complete, drilled for fixing of steel sheeting or other covering etc, to prepared for hanging or sliding with including either hooks and hinges also fastening grills, grating, hold fast of doors and windows chowkhat etc, with ends of bars shouldered and or riveted, or forget into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walkways; railings; framework of water tanks and similar work confirming to Fe 290 Gde E-165 complete all as specified.

M&L for Mild steel bars TMT bars 5mm dia and over upto and including 10mm dia in strriups,spaces,nibs and binders etc complete all as specified.

M&L for brick work in CM ( 1:6 ) with using sub class `B ` modular fly ash brick straight or curved on plan exceeding 6.0m mean radius complete all as specified.

M&L for rendering 15mm thick in CM 1:4 on fair faces of brick or concrete surface of wall and finished even and smooth without using extra cement complete all as specified.

M & L for preparation of new plastered surfaces of walls and applying two coats of Cement Base Paint all as specified. Make : Asian- Apex or other equivalent as approved by GE.

Excavating over areas not exceeding 1.5 m deep and getting out in hard/dense soil complete all as specified.

M&L for filling approved earth brought from outside Defence land of any lead in floors in layer n.exc 15cm thick watering and well ramming/consolidation complete all as specified and directed. NOTE :Quoted rate shall be inclusive for earth brought from approved quarry outside Defence land of any lead and nothing extra will be paid.

M&L for Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering as required complete all as specified.

M&L for Hard core with broken stone of gauge n exc 63 mm deposited, spread, levelled in layers n.exc 15cm including watered, rammed to true surface complete all as specified and directed.

M&L for PCC 1:3:6, type C1 using 20mm graded stone aggregate as in sub base of floor complete all as specified.

M & L for high strength steel deformed TMT bar 10 mm dia and over, cut to length, bent to shape required including cranking, bending spirally and binding with and including mild steel wire (annealed) not less than 0.90 mm dia, etc complete all as specified.

M&L for RCC M-25 grade concrete (Design Mix) using 20 mm graded stone aggregate as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified. NOTE : Reinforcement shall be measured and paid separately under relevant item.

M&L for RCC M-25 grade concrete (Design Mix) using 20 mm graded stone aggregate as in Columns, pillars, piers, posts and struts complete all as specified. NOTE : Reinforcement shall be measured and paid separately under relevant item.

M&L for RCC M-25 grade stone (Design Mix) using 20 mm graded stone aggregate as in beams, bands, cantilvers, bressummers, lintels, chajjas, over 1.5m span complete all as specified. NOTE : Reinforcement shall be measured and paid separately under relevant item.

M&L for RCC M-25 grade concrete (design Mix) using 20 mm graded stone aggregate as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like, etc complete all as specified. NOTE : Reinforcement shall be measured and paid separately under relevant item.

M & L for use and waste of formwork to sides of concrete foundations, footings, bases of columns, raft and beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to Better fair finished surface of concrete complete all as specified.

M & L for use and waste of formwork to sides of pillars, posts, struts, piers, columns and stanchions fair finished surface of concrete complete all as specified.

M & L for use and waste of formwork to sides and soffits of floor or roof beam, beam hauchings, bands, girders, bressummers, lintels, etc for fair finished surface of concrete complete all as specified and directed

M & L for use and waste of formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work, not exceeding 200mm thick (horizontal or sloping), etc fair finished surface of concrete complete all as specified.

M&L for rendering 15mm thick on fair faces of brick work or concrete surfaces in cement mortar (1:4) finished even & smooth complete all as specified.

M & L for applying two coats of 2nd quality exterior weather proof water base emulsion paint of approved colour over a coat of primer of same make complete all as specified. (Make :- Asian-ACE/Berger- Wallmasta/Nerolac-suaksha).

M&L sand filling under floor including watering and consolidaion complete all as specified. NOTE: Thickness shall be measured after consolidation.

M & L for brick work with sub class 'B' modular bricks, straight or curved on plan to any radius built in CM 1:4 in half brick thick wall complete all as specified.

M & L for use and waste of timber formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor, roofs and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide complete all as specified.

M & L for 25mm thick, plain cement concrete 1:2:4 type B0 (using 12.5 mm graded stone aggregate) as in levelling course for floors complete all as specified.

M & L for 75mm thick cement concrete 1:3:6 type C1, using 20mm graded stone aggregate as in floor/ plinth protection finish the surface even and smooth with using extra cement including filling the expansion joints with bitumen filler / filler boards and necessary form work etc complete all as specified.

M&L for rendering 10mm thick in CM 1:6 on other than fair faces of brick work or concrete surfaces finished the surface even and smooth without using extra cement complete all as specified.

M&L for rendering 15mm thick in CM 1:4 on fair faces of brick or concrete surface mixed with liquid water proofing compound @ 200 ml per bag, finished the surface even and fair without using extra cement complete all as specified. NOTE:- Liquid water proofing compound shall be measured and paid separately under relevant items.

M&L for rendering 5mm thick in CM 1:4 on ceiling or concrete surface, finished even and smooth without using extra cement complete all as specified.

S&F factory made solid PVC door frame of size 50mm x 47mm made out of plain 5mm plain colour PVC sheet reinforced with MS square tube, with wooden grain printed PVC sheet used inserted of plain colour PVC sheet & edges will be painted to match with printed sheet complete all as specified.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail & bottom rail. Panelling of plain colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, complete all as specified.

S&F 100 mm size Butt hinges medium weight cold rolled mild steel and fixed.

S&F 150 mm long Aluminum anodized barrel tower bolts of extructed section.

S&F aluminum alloy handle fabricated anodised of 150 mm long.

S&F fabricating coloured powder coated aluminium frame work,door shutter ,windows , ventilators, partitions with one or more rebate sections of approved tint as required for partitions including beading,cleat, screws,fasteners, plugs, for fixing with wall/ceiling columns/beams etc complete all as specified.

S&F aluminium coloured power coated window and ventilator shutters, sliding type without sash bar aluminium section weighing 0.55 kg/m including necessary locking arrangement, guide wheels, joining cleats, glazing clips, rubber packing anodised aluminium snap beading screws etc complete all as specified.

S&F aluminium coloured power coated door shutters, aluminium section weighing minimum 0.55 Kg/m including necesssary joining cleats, glazing clips, rubber neoprene packing handle 2 Nos in each door, pad lock, hinges, anodised aluminium snap beading screws etc complete all as specified.

S&F 4.8 mm thick plain or tinted glass, ordinary quality including rubber gasket for packing and fixed to aluminium doors/window/partition including necessary cutting / moulding and chamferring of edges for service window/counters complete all as specified.

S & F galvanised Stainless steel wire cloth of 0.45mm dia wire and average width of aperture 1.4mm & fixed with tacks of stainless steel wire staples,etc complete all as specified.

S&F aluminium (extructed section) Door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutter and fixed complete all as specified.

M & L for applying two coats of 1st Quality oil emulsion distember over new prepared surface of wall with putty complete all as specified . NOTE : Putty shall be measured and paid seperately under Ser Item No. 55.

M & L for preparation of new plastered surfaces of walls and applying two coats of Acrylic Smooth exterior paint of required shade (@ 1.67 litre/10 sqm) over a coat of primer(@ 2.20 kg/10 sqm) of same make base over a coat of putty all as specified. Note :- Putty shall be measured and paid seperately under Ser Item No. 55 Make : Asian- Apex or other equivalent as approved by GE.

M&L for preparation of newly plastered surface of wall and applying two coats of cement base wall care putty (each coat not less than 1mm) on walls finished even and smooth with sand paper complete all as specified.

M & L for preparing new plastered ceiling surface and applying three coats of white wash complete all as specified.

M&L for non –skid ceramic coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm in floors etc set and jointed in neat cement slurry and pointed in coloured cement to match with colour of tile over and including 15mm thick screed bed in CM 1: 6 complete all as specified.

M&L for glazed ceramic coloured tiles of size not less than 450x300x7 mm thick as in vertical surfaces such as wall, dado ,skirting etc set and jointed in neat cement slurry and pointed with coloured cement to match with colour of tile over and including 10 mm thick backing coat in CM (1:4) complete all as specified.

M&L for 18-20 mm thick Black granite slab of approved quality of any size bedded and jointed in grey cement slurry and pointed with white cement mixed with admixture of pigment to match the shade of granite stone laid over and including 15 mm thick screed bed in CM (1:4) including polshing by using mechanical grinder and moulding edges complete all as specified.

M&L for 60mm thick machine pressed rubber moulded precast concrete interlocking paver block (glossy finish) of M-35 Grade of approved shape, size and colour conforming to IS 15658-2006 including joints filled with sand, and laid over compacted dry sand cushioning complete all as specified. NOTE: Sand cushioning shall be moulded and paid separately under relevant item.

M & L for rendering 10mm thick in cement mortar 1:3 mixed with integral water proofing compound while concrete surface is green and finish the surface even and smooth without using extra cement all as specified. NOTE : WPC shall be measured and paid separately under respective item.

M & L for preparation of surfaces for applying bituminous primer (conforming to IS-3384-1965) @ 0.40 Kg/Sqm complete.

M & L for applying two coats of industrial bitumen of grade 85/25 at the rate of 1.2 Kg per Sqm including cleaning surfaces complete all as specified. NOTE : 1st coat for bonding below membrane and 2nd coat on top of membrane.

M&L for 3mm thick APP based polymeric membrane minimum weighing 3kg/sqm and reinforced with polyster non woven fabric (weight not less than 150 gms/sqm) laid on primed surface by torched application all as per manufacher's instruction complete all as specified and directed. Note: Application of APP membrane shall be done by authorised applicator of membrane manufacturer.

M&L for applying two coats of bitumen based aluminium painting @ 0.15 Kg / sqm each coat on APP membrane including preparation of surface complete all as specified.

Supply only Liquid Water proofing compound PIDIPROOF LW+ of Dr FIXIT or other equivalent as approved.

S& F Rotational moulded Polyethylene water storage tank 1000 litres capacity (cylidrical vertical with closed top) double layered hoisted and fixed in position all as specified in SSR part I.

S&F 15mm bore steel tubing medium grade ,galvanized with all fitting such as bend ,elbow, socket,tees,and fixed complete to wall or in ceiling or in floors including cutting threading and making forged bends on pipes MS hooks etc ,complete all as specified.

All as per item no 68 above but 20mm bore.

S&F Gun-metal, globe or gate valves,with iron wheel head, screwed both ends for iron pipe of 15mm dia and fixed complete all as specified.

S&F CP pillar taps (swan neck type) cast copper alloy CP with capstan head, screwed down ,high pressure with long screwed shanks and fly nuts fixed in 15 mm bore pipes complete all as specified. Make :Plumber/Essco of jaguar (Economical Range)

S&F CP angle stop cock of 15mm bore screwed down for high pressure with crutch or butter fly handle ,screwed both end for iron pipes complete all as specified. Make :Plumber/Essco of jaguar(Economical Range).

S&F fancy type chromium plated15mm bore two way Bib cock cast copper alloy with crutch or butterfly handle, screwed for iron pipe or brass ferrule etc complete all as specified . Make :Plumber/Essco of jaguar(Economical Range)

S& F CP toilet paper holder complete all as specified.

S& F Corner Glass Shelf as approved by GE complete all as specified.

S&F vitreous china wash down water closet pedestal pattern white excluding flushing cistern and flush pipes complete all as specified.

S&F PVC valveless, syphonic action type flushing cistern of 10 litres capacity low level ,white with inlet ball valve,float and handle including brackets and connection to pipe and fixing of chain and pull or lever if any complete all as specified. Make: Plumber/Essco of jaguar (Economical Range)

S&F health faucet with flexible pipe of one metre length including wall hook for EWC complete all as specified. Make: Plumber/Essco of jaguar (Economical Range)

S & F vitreous china wash basin white (oval shaped under counter) of size 550 x 400mm including 32mm brass CP waste coupling complete all as specified.

S&F Vitreous China Urinal, Half stall type,white with grating and union for discharge pipe, urinal spreader with waste pipe and all fitting for urinal complete all as specified and as directed

S & F PVC (SWR) multi floor trap with stainless steel grating including joining to waste pipe with solvent cement, dia of outlet 75mm bore complete all as specified.

S&F PVC connection 15mm size with PTMT nuts of length 450 mm long complete all as specified.

S&F PVC waste pipe for urinal/wash basin/ sink pipe 32mm bore 65cm long complete all as specified.

S&F 20mm bore ball valve high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipes and fixed. ( Minimum Weight 210 gms).

S&F 75mm bore of PVC (SWR) pipes single socketed in any length with rubber ring joints laid on wall / floor complete all as specified.

S&F PVC ( SWR) bends any radius bore of 75 mm.

S&F 75mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified.

M&L for SGSW drain pipe of 150mm internal dia laid in trenches and jointed in cement mortar (1:1) complete all as specified.

M&L for PCC (1:3:6) type C2 using 40mm graded stone aggregate as concrete bed to drain pipe of 150mm dia including packing under and haunching against the sides of pipe after they are laid and tested complete all as specified.

M&L for RCC 1:2:4 type B1 using 20 mm graded stone aggregate as in precast coverslab for manholes and soak well cover slab etc set in cement mortar (1:4) etc with and including necessary form work complete all as specified. Note : Reinforcement shall be measured & paid separately under relevnat item.

M&L for plain cement concrete 1:3:6 type C2 using 40 mm graded stone aggregate as in foundations, filling,mass-concrete and coping complete all as specified.

Surface excavation n.exc. 30cm deep and averaging 15cm deep and getting out in soft/disintegrated rock complete all as specified.

Excavation in trenches n.exc. 1.5 m wide and n.exc. 1.50 m in depth for foundation manholes etc and n.exc. 10 Sqm on plan and getting out in soft/disintegrated rock complete all as specified.

Returning, filling in, soft/disintegrated rock including spreading, levelling, watering and well ramming in layers not exc 25 cm. complete.

Removing excavated materials (soft/disintegrated rock) to a distance not exc. 50 metre and depositing where directed at a level not exc. 1.50 above the starting point complete all as specified.

M&L for preparation of new or previously untreated steel surface of any description over 10cm in width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified.

S&F mild steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I.S 1161-1979 grade St. 240 as in frame work for sun shade, roof projection and vertical section etc. complete all as specified.

S&F rolled mild steel section as in main and cross beam, hip and jack rafters; purlin where connected to common rafter and running rail and guides for sliding door, fixed with angle cleat or other connecting plates conforming to 410-W (Gde-E-250) quality A complete all as specified.

S&F Pre-painted Galvalume/ Zinkalume corrugated sheeting 0.50 mm thickness as in roof, etc, having crest depth 28-30mm at a pitch of 195-250 mm and having 2 ribs in between for addition strength fixed with zink coated self drilling fastener including EPDM washer complete laid with one corrugation side laps and min 150mm end lap complete all as specified.

S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in ridges, hips, valley gutter, with self tapping screws as specified.

M&L for Machine cut Kota stone slab flooring 20 mm thick (+ 2mm) of size 58cm x 58cm (nearest size as available in the market) laid over and including 25 mm thick PCC 1:2:4 type B1 using 20mm graded stone aggregate and 15mm thick screed bed in cement mortar 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing to mirror finish, complete all as specified.

Bharadwaj Builders

M/S UnitedConstruction

Auto Traders

Sudarshan Associates