COMPREHENSIVE MAINTENANCE OF B/R AND E/M AND ALLIED WORKS TO OFFRS MD ACCN, OFF MESS MES IB AND OTHER BUILDINGS AT BOLTON ROAD AND CAW UNDER GE (AF) HAKIMPET

Demolition of brickwork or stone masonry including all quoins, arches, pillars, etc., built in cement mortar complete including disposal of debris all as directed.

M&L, brickwork with using old size Flyash bricks, straight or curved on plan exceeding 6m mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L, 15mm thick rendering in cement mortar 1:6, on fair faces of brick or concrete surfaces, in any height, finished even and smooth without using extra cement complete all as specified and directed.

Dismantling of floor, hearth or wall tiling including cement mortar bedding (but not backing) and removing the rubbish off the premises all as specified and directed.

Demolition of cement concrete of any description and in any position not otherwise specifically provided for complete including disposal of debris at low laying areas as directed by Engr-In- Charge

M&L, 40mm thick PCC 1:2:4 type B-0 using 12.5mm graded stone aggregate as in flooring, finishing the surface even and smooth with out using extra cement including necessary formwork complete all as specified and directed.

M&L, light coloured vitrified tiles in floors of size 600 x 600 x 9 to 10mm thick, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile over and including screed bed or bedding layer 15mm thick in CM 1:6 complete all as specified and as directed complete all as specified and as directed. Note: Shade and design/pattern of tiles shall be as directed by GE.

M&L, 9 to 10mm thick light coloured vitrified tiles in skirting of size 600 x 100mm, set and jointed in neat cement slurry and pointed in coloured cement to match shade of tile over and including 10mm thick backing coat in CM 1:3 complete all as specified and as directed.

M&L, 7 to 8mm thick coloured, joint free Non skid ceramic tiles of size area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile over and including screed bed or bedding layer 15mm thick in cement mortar 1:6 complete all as specified and as directed. Note: Shade, design/pattern of tiles shall be as approved by GE

M&L, coloured glazed ceramic tiles of size 300 x 450mm, 6 to 7mm thick in dado etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile over and including 10mm thick backing coat in CM 1:3 complete all as specified and as directed.

M&L, 7 to 8mm thick coloured, joint free Non - skid Ceramic tiles of area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile over and including screed bed or bedding layer 15mm thick in cement mortar 1:6 complete all as specified and as directed. Note: Shade, design/pattern of tiles shall be as approved by GE

M&L Cement concrete tiles with grey cements and pigments 30cm x 30cmx 20mm thick, machine pressed; set jointed and pointed in neat cement slurry in floors, and cut and polished and including screed bed or bedding layer 15mm thick in cement mortar 1:6 complete all as specified and as directed.

Demolition of stone slabs, tiles, cement concrete tiles/paver blocks of any description or thickness in floors, laid and bedded in any mortar including disposal of debris off the premises complete all as directed.

M&L, 18 to 20mm thick, approved machine cut, coloured Granite, factory polished, edges rounded in steps, cooking platform and the like laid over and including screed bed or bedding layer 20mm thick in cement mortar 1:4, pointing with white cement (1:2) using marble dust with admixture of pigment to match the shade of granite stone complete all as specified and directed.

M&L, 12 to 18mm thick machine cut coloured granite, factory polished, in wall lining, (veneering to wall) over 10mm thick backing coat in cement mortar 1:3 and pointing with white cement 1:2 using marble dust with admixture of pigment to match with shade of granite complete all as specified and as directed

Taking down chowkhat or frames (without taking off shutters from the frames) not exceeding 1.5Sqm complete all as directed.

Taking down chowkhat or frames (without taking off shutters from the frames) exceeding 1.5Sqm but not exceeding 4Sqm each complete all as directed.

Taking down shutters of any description from the frames exceeding 1Sqm but not exceeding 2Sqm complete all as directed.

S&F Factory made single extruded WPC (WoodPolymer Composite) solid door/ window/Ceosetory windows & other Frames/Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp ressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately).

S&F in repairsFactory Made single extruded WPC (Wood polymer composite) solid decorative type flush door shutter of 30 mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powedr/rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face ) and 900 N (Edge), minimum compressive strength 50 N.mm2, modulus of elasticity 850 N.mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hings of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-in-Charge.

S&F, 30mm thick Flush shutters, solid core construction, with particle board core and plywood face panels, commercial type on both sides and one face is covered with decorative face veneer with lipping complete all as specified and directed.

S&F, 30mm thick second class hardwood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc., (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, gauze, etc., complete all as specified and directed. Note: Sizes of members of shutters as specified in SSR Part I.

S&F, in opening solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with mild steel square tube complete all as specified and as directed.

S&F, Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of mild steel tubes for top and bottom rails, mild steel frames shall be covered with heat moulded plain colour PVC "C" channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the mild steel frame welded/ sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement all as specified and directed.

S&F, 100mm size stainless steel butt hinges, medium weight complete all as specified and as directed.

S&F, 200mm long aluminium anodized barrel tower bolts of extruded section complete all as specified and directed.

S&F, 150mm size, extruded aluminium anodized handles, fabricated type, complete all as specified and as directed.

S&F, 300mm long aluminium anodized sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy complete all as specified and directed.

S&F, 150mm long (overall length of cover plate) floor door stopper of aluminium alloy body and tongue, anodized, with hard drawn steel spring, fixed in floor complete all as specified and directed.

S&F in repairs 19/20 mm Plywood, grade BWR, fixed with screws to timber frame work.

S&F 0.9mm thick decorative laminates type I, or surface finish , any clour and pattern as approved .

S & F in repairs continuous (piano) hinges,mild steel, bright finish or electrogalvanised width of flap when open 38/40 mm

S& F in repairs 40mm dia, cupboard knobs fixed with nut, screw and washer of mild steel, bright finished

S& F in repairs auto closing mild steel hinges with spring for , cupboard fixed with nut, screw and washer of mild steel, bright finished

M&L, preparing new or previously untreated wooden surfaces over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer including preparation of surfaces complete all as specified and as directed.

S&F Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, fixed complete all as specified and directed.

S&F in repairs, stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks, or stainless wire staples complete all as specified and as directed.

S & F repairs aluminium body Door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed in repairs all as specified and directed.

S&F Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flangesof 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre /intermediate channel0.9 mm thick having two equal flanges of 15 mm each and webof 45 mm suspended from soffit at approx 900 mm centreto centre with Gl cleat and steel expansion fasteners with and including ceiling section(not exc 1.2 m length) of 0.55mm thickness having kurled fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre tocentre. Hangers 6 mm dia. G.I. (upto1200mm length) adjusting levelfixed to roof slabs by means ofceilling cleats made out of G.I.flat 40 x 3 mm size 60mm longand expansion hold fasteners12.5mm dia. 40mm longcomplete all as specified

Dismantling of wall and ceiling boards (fiber, pulp , insulation etc)or insulation boards /slabs /blankets any thickness including cover fillets, grid work any description and any position all as directed.

M&L for 12 mm thick gyprock false ceiling boards of size 600mmx600 mm fixed or laid/inserted to timber/GI/Aluminium frame work with screws including two coats of OBD over primer on ceiling surfaces

S&F mild steel clamps, hold fasts and similar small articles conforming to Fe-290, Gde-E-165 complete all as specified and directed.

Dismnantling of wrought iron or mild steel works of any description not otherwise provided for complete all as directed.

M&L welding in repairs not exc 2.5cm in length not exc 6 mm thick

M&L welding in repairs exc 2.5cm not exc 5.0 cm in length not exc 6 mm thick

Dismantling of Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings all as specified and directed.

M&L for Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified and directed.

M&L for Pre- painted galvatume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified and directed.

S&F Steel work in tubular trusses / purlines including special shaped washer etc. complete using ERW or including butt welded tubes conforming to I. S.1161-1979 grade St.-240

S&F in repairs, mild steel framed work such as grills, gratings etc., framed guard bars and similar works conforming to Fe 290 Gde-E-165 complete all as specified and as directed.

M&L, preparing new or previously untreated steel surfaces over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer including preparation of surfaces complete all as specified and as directed.

S&F in repairs, vitreous china wash hand basin white 550x400mm of size including cutting for and pinning in ends of brackets or erecting stand including brackets, PVC waste pipe and coupling of suitable size including removal of debries off the premises complete all as directed

S&F in repairs, stainless steel kitchen sink with drainage board, 1mm thick with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 915mm x 460mm with bowl size 410mm x 330mm x 160mm complete all as specified and directed.

S&F in repairs, stainless steel sink 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm with bowl size 410mm x 330mm x 160mm complete all as specified and directed.

S&F in repairs, stainless steel plate rack of size 900mmx600x200mm 1mm thick , including bedding in cement mortar to dwarf wall or including fixing cantilever brackets complete all as specified and directed.

S/F in repairs glass corner shelf of size 9" dia with chromium plated rail etc complete all as specifed Cat No: ACN 1173 of Jaguar or equivalent

Supply and fixed in repairs PTMT bath room mirror cabinet of size 330x430mm complete all as specified and as directed MAKE: CAT No 551 of PRAYAG or equivalent model in POLYTUF as approved by GE

S&F in repairs, plastic water closet seat cover, white, closed pattern with recessed bottom and cover aluminized hinging device complete all as specified and directed.

S&F in repairs, mild steel chromium plated towel rail, 'D' shaped, 20mm dia, 600mm long, premium quality complete all as directed.

S&F in repairs, 32mm dia brass chromium plated waste coupling fittings for wash hand basin etc., with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed complete all as specified and as directed.

S&F in repairs, 100 mm dia brass chromium plated waste coupling fittings for stainless steel kitchen sink etc., with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed complete all as specified and as directed.

S&F in repairs first quality vitreous China wash down water closet pan (pedestal pattern), white, of size not less than 400mm x 400mm x 340mm (excluding fixing bolts, flushing cistern and flush pipe) but including provision of plastic water closet seat, white , closed pattern with flat bottom, and cover and mild steel chromium plated hinging device complete all as specified and directed.

S&F in repairs, vitreous china squatting pan, ‘Orissa’ pattern of size 580 x 440mm, white, with integral foot rests, including connection to trap, and to flushing pipe, antisyphonage pipe, etc., complete including provision of cement concrete bedding in 1:5:10 and making good to floor complete all as specified and directed.

Taking up or down GI tubing incl connections of 20 mm dia bore.

All as per item No. 65 above, but 15mm dia bore

Cutting chases, in stone walls, pinning in, making good to facing where required and pointing in cement mortpor 1:3 for concealed water tubing and making good, cuting exc, 10 cm but n.exc 20 cm girth.

Supplying and laying 20 mm outer dia of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified including all necessary brass threded elebow , T ect all fittings . all as specified and directed.

All as per item No. 68 above but 25 mm bore including all necessary brass threded elebow , T ect all fittings . all as specified and directed.

Demolition and breaking up drain pipes of upto 100mm dia

S&F 75mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors all as specified and as directed.

S&F 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors all as specified and as directed.

S&F PVC (SWR) pipes single socketed,in any length with rubber ring joints, fixed to walls bore of the pipe 110 mm.

S&F PVC (SWR) pipes single socketed,in any length with rubber ring joints, fixed to walls bore of the pipe 75 mm.

S&F 110 mm bore PVC (SWR) bends any radiuis all as specified and as directed

S&F 110 mm bore PVC (SWR) bends with access door any radiuis all as specified and as directed

S&F 75 mm bore PVC (SWR) bends any radiuis all as specified and as directed

S&F 75 mm bore PVC (SWR) bends with access door any radiuis all as specified and as directed

S&F 110 mm bore PVC (SWR) junction single, (single T) all as specified and as directed

S&F 110 mm bore PVC (SWR) junction single, (single T) with access door all as specified and as directed

S&F 75 mm bore PVC (SWR) junction single, (single T) all as specified and as directed

S&F 75 mm bore PVC (SWR) junction single, (single T) with access door all as specified and as directed

S&F Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified.

Supply and fixed in repairs Wall Mixer with Provision for overhead Shower with 115mm Long Bend Pipe on Upper Side, Connecting Legs & Wall Flanges Make :- Jaquar Code No CQT-CHR-23273UPR

S&F in repairs Flushing cistern,PVC valveless, syphonic action type 10 litre capacity,low level, white, with inlet,ball valve, float and handle and brackets and 32mm dia PVC flush pipe complete all as specified.

S&F in repairs, 500litres capacity triple layered rotational moulded polyethylene water storage tank (cylindrical vertical with closed top) hoisted and fixed in position including connecting up of existing inlet and outlet pipes and ball valve complete including dismantling of old tank all as specified and as directed.

All as per item No 86 above but 1000litres capacity.

All as per item No 86 above but 2000litres capacity.

S&F in repairs, 15mm bore bib taps, long body, fancy type, chromium plated, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron/GI pipe or for brass ferrule complete all as specified and directed.

S&F in repairs, 15mm bore two way bib taps, long body, fancy type, chromium plated, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron/GI pipe or for brass ferrule complete all as specified and directed.

S&F in repairs, 15mm bore Pillar taps, cast copper alloy, fancy type with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron/GI pipe and fixed complete all as specified and directed.

S&F in repairs, 15mm bore angle valve, cast copper alloy, chromium plated, fancy type, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron/GI pipe or for union complete all as specified and directed.

S&F in repairs, 125mm size chromium plated shower rose with or without swivel joint complete all as specified and directed.

S&F in repairs, PVC connections 15mm size with PTMT nuts of length 600mm, complete all as specified and directed.

S&F in repairs, 150mm size, extruded aluminium anodized handles, fabricated type, complete all as specified and as directed.

S&F in repairs, 100mm size, extruded aluminium anodized handles, fabricated type, complete all as specified and as directed.

S&F in repairs, 200mm long aluminium anodized barrel tower bolts of extruded section complete all as specified and directed.

S&F in repairs, 100mm long aluminium anodized barrel tower bolts of extruded section complete all as specified and directed.

S&F in repairs, 300mm long aluminium anodized sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy complete all as specified and directed.

S&F in repairs, 100mm size stainless steel butt hinges, medium weight complete all as specified and as directed.

S&F in repairs, 150mm long (overall length of cover plate) floor door stopper of aluminium alloy body and tongue, anodized, with hard drawn steel spring, fixed in floor complete all as specified and directed.

S&F in repairs, 25 mm dia mild steel chromium plated curtain rod, including suitable matching brackets , stops , rollers ect , complete all as specified and directed.

S&F, Roof trusses (framed), trussed, purlins, crane gantries rails and fastenings and heavy bracket framing (beam, tee, angle, channel or flat sections) including distance pieces, cleats etc., conforming to Fe 410W (Grade E-250) quality 'A' complete all as specified and directed.

M&L, preparation of old painted steel surfaces of any description, over 10cm in width or girth not otherwise described and applying one coat of synthetic enamel paint complete all as specified and as directed.

Repairs to aluminium door shutters n exc 2 sqm in area easing, removing/ refixing in same position with required hardware and screws for free operation of the shutter complete all as specified and directed.

Repairs to aluminium window shutters n exc 1.5 sqm in area easing, removing/ refixing in same position with required hardware and screws for free operation of the shutter complete all as specified and directed.

S&F Toughned glass of thickness 12 mm as in hinged doors, partitions automatic doors and similar work including cutting to shape, drilling holes required including cleats frame brackets iuncluding all fittings complete all as specified and directed.

Material & Labour for providing and fixing stainless steel (Grade 304) railing made of hollow tubes,channels, plates etc., including welding, grinding,buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories &stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement.

M & L for Pre-cast cement concrete block masonry with solid blocks, Type C1 1:3:6 (20mm graded aggregate) exc. 10 cm in width and setting in cement mortar 1:6, complete

Taking down copper / aluminum point wiring (light, fan, socket or power) complete, including fixtures and fittings such as switches, ceiling roses, pendants, regulators, sockets, lamp holders, light fittings etc removing materials and making good disturbed surfaces of walls, floors etc, including paint tuch up to match with the existing surface as per site requirement, complete all as specified and directed.

One light point controlled by one way switch.

One light point controlled by two way switch.

One ceiling fan/ exhaut fan point controlled by one one way switch.

One 3 pin socket outlet 5 Amps on the same board with other switches.

One 3 pin socket outlet 5 Amps on the Independent board.

One bell/ buzzer point controlled by one push button n the same board with other switches or independent.

All as per item No. 111 here-in-before but conductor drawn through stove enamelled 20 mm dia medium grade steel conduit for one light point controlled by one flame proof switch, complete all as specified and directed.

All as per item No. 111 here-in-before but with 4 Sqmm for 3 pin 15 Amps socket point controlled by one switch on independent board and 4 Sqmm copper conductor green in colour as earth continuity conductor, complete all as specified and directed.

One light point controlled by one way switch

One light point controlled by two way switch

One ceiling fan/ exhaut fan point controlled by one way switch.

One 3 pin socket outlet 5 Amps on the same board with other switches.

One 3 pin socket outlet 5 Amps on the Independent board.

One bell/ buzzer point controlled by one push button on the same board with other switches or independent.

All as per item No. 114 here-in-before but with 4 Sqmm for 3 pin 15 Amps socket point controlled by one switch on independent board and 4 Sqmm copper conductor green in colour as earth continuity conductor, complete all as specified and directed.

S&F Switch piano flush type, single pole one way 6 Amps 240 volts, complete all as specified and directed.

Supply and fix Switch Piano flush type two way 6 Amps, complete all as specified and directed.

Supply and fix socket piano flush type Socket outlet 2 in 1, 3 pin, 6A complete all as specified and directed

Supply and fix Switch socket combination 2 in 1, 5 Pin, 6 Amps flush type, complete all as specified and directed.

Supply and fix Switch socket combination, 3 pin, 6 and 16A, 5 in 1 flush type, complete all as specified and directed.

Supply and fix Switch bell push 6 Amps flush type, complete all as specified and directed.

S&F Stepped type electronic fan regulator flush type, complete all as specified and directed.

Supply and fix Modular switch 6A, 1 way, complete all as specified and directed.

Supply and fix Modular switch 16A, 1 way, complete all as specified and directed.

Supply and fix Socket outlet, 5 pin, 6A modular, complete all as specified and directed.

Supply and fixing Socket outlet, 6/16A modular, complete all as directed.

Supply and fixing switch bell push modular, complete all as directed.

Supply and fixing Fan regulator, 2 modular, complete all as directed.

Supply and Fixing bell Ding Dong AC, 230 Volts, SP, complete all as specified and directed.

Supply and replacement in repairs, Switch flame proof rotary type with termination box in LM6, 16A, single pole 250V. Make : M/S Shyam Switchgears / M/S Sudhir / M/S Baliga

Supply and fixing in repair LED light fitting 2 x 16 Watt flame proof, CMRI certified recommended for gas/ vapor group of IIA & IIIB, Zone 1 & 2 and IP 65 protection with die cast aluminum housing with heat resistant toughened glass with and LED tube light fixtures driver, holders, connector etc. Complete with all accessories prewired and including connecting up with three core flexible copper conductor cable with suitable size complete all as specified and as directed. Make : M/S Shyam Switchgears / M/S Sudhir / M/S Baliga as approved by GE.

Suppy and fix in repairs, wall mounted 1 x 10 W LED 220V, AC, 2' batten type with extruded Al, heat sink, integral driver, energy efficient, ready to use pack etc, complete with all accessories internally pre-wired and fixing the same on and including two Nos. PVC blocks and connecting up with twin core twisted flexile copper conductor cable of suitable size upto ceiling rose including taking down old one. Make: Havells/ Philips/Crompton/Syska.

Suppy and fix in repairs, wall mounted 1x 20W LED 220V, AC, 4' batten type, with extruded Al, heat sink, integral driver, energy efficient, ready to use pack etc., complete with all accessories internally pre-wired and fixing the same on and including two Nos. PVC blocks and connecting up with twin core twisted flexile copper conductor cable of suitable size upto ceiling rose including taking down old one. Make: Havells/ Philips/Crompton/Syska

Taking down the old unserviceable recess mounted fitting of any type, supply and fix, new ultra modern architectural 2'x2', recess mounted, 36W LED light fittingwhich provides soft-light and glare free symmetrical illumination suitable for Armstrong/Grid ceiling. including modification of the false ceiling as required, complete all as specified and directed. Make : Havells/ Philips/Crompton/Syska

Taking down the old unserviceable recess mounted fitting of any type, supply and fix, Square/round recess mounted 15 W LED light fitting, with high quality aluminium die cast body, high efficient constant current LED driver, including modification of the false ceiling as required at site, complete all as specified and directed. Make: Havells/ Philips/Crompton/Syska

Taking down of unserviceable building security lights of any type, Supply and fixing LED street light fitting 35 Watt 230 V AC outdoor type with high pressure diecast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete.complete all as specified and directed. Make:Havells/Phillips/CG/Bajaj.

Taking down unserviceable sub main wiring of any description and M&L for sub main wiring with 3x1.5 Sqmm, (Ph+E+N) , FRLS PVC insulated, unsheathed, multi stranded,1100 volts grade copper conductor cable , single core, drawn through and including rigid PVC conduit of suitable size with all conduit accessories complete all as specified and directed. Note: Three runs (P+N+E) of 1.5 Sqmm copper cable and one run of 20 mm dia, rigid PVC conduit with all conduit accessories shall be measured as one unit length.

Description all as per item No 137 here-in-before but with 3x2.5 Sqmm, complete all as specified and directed. Note: Three runs (P+N+E) of 2.5 Sqmm copper cable and one run of 20 mm dia, rigid PVC conduit with all conduit accessories shall be measured as one unit length.0

Description all as per item No 137 here-in-before but with 3x4.0 Sqmm, complete all as specified and directed. Note: Three runs (P+N+E) of 4.0 Sqmm copper cable and one run of 20 mm dia, rigid PVC conduit with all conduit accessories shall be measured as one unit length.

Description all as per item No 137 here-in-before but with 3x6.0 Sqmm, complete all as specified and directed. Note: Three runs (P+N+E) of 6.0 Sq mm copper cable and one run of 25 mm dia, non metallic, med. gr. rigid PVC conduit with all conduit accessories shall be measured as one unit length.

Description all as per item No 137 here-in-before but with 4x10.0 Sqmm (3Ph+1N) + 1x10.0 Sqmm (Earth), complete all as specified and directed. Note: Six runs of 10.0 Sqmm copper cable and one run of suitable size dia, rigid PVC conduit with all conduit accessories shall be measured as one unit length.

Taking down unserviceable sub main wiring of any description and M&L for sub main wiring with 3 runs of 4.0 Sqmm, FRLS PVC insulated, unsheathed, multi-stranded, 1100 Volts grade copper conductor calbe, single core, drawn through and including double locked type PVC casing & Capping and its all accessories of suitable size on wall/ roof surfaces, complete all as specified and directed. Note: Three runs 4.0 Sqmm copper cable and one run of suitable width of PVC casing and caping shall be measured as one unit length.

Desrciption all as per item No. 142 here-in-before but with 3x6.0 Sqmm, complete all as specified and directed. Note: Three runs 6.0 Sqmm copper cable and one run of suitable width of PVC casing and caping shall be measured as one unit length.

Desrciption all as per item No. 142 here-in-before but with 4x10.0 Sqmm (3Ph+1N) + 1x 10.0 Sqmm (Earth), complete all as specified and directed. Note: Six runs 10.0 Sqmm copper cable and one run of suitable width of PVC casing and caping shall be measured as one unit length.

Supply and fix in repairs including taking down the following unserviceable Items:-

(a) Lamp holder PVC/ Polycarbonate type with back plate suitable for batten/ angular type.

(b) Ceiling rose PVC/ Polycorbonate insulated body with three terminals.

(c) Switch Piano, Flush type single pole, one way 6 Amps

(d) Switch Pian flush type two way 6 Amps

(e) Socket outlet 2 in 1, 3 pin, 6A

(f) Switch Socket Combination 2 in 1, 5 Amps flush type

(g) Switch Socket combination 3 Pin, 5 and 15 Amps 5 in 1 flush type

(h) Switch Bell push 5 Amps flush type

(j) Stepped type electronic fan regulator flush type

(k) Modular Switch 6A 1 Way

(l) Modular Switch 16 A 1 Way

(m) Socket outlet 6 A Modular

(n) Socket outlet 16 A modular

(o) Switch Bell push modular

(p) Fan Step regulator modular

(q) Bell Ding Dong AC 230 Volts

(s) Surface mounting PVC/Poly carbonate Box of 6 Amps Socket with switch

(t) Surface mounting PVC/Poly carbonate Box combined 2 hole for 6/16 Amps Socket with Switch

(u) Plug top polycarbonate 3 Pin 5 Amps

(v) Plug top Polycarbonate 3 Pin 15 Amps

M&L for Taking down ceiling fan of any description, sealing cable ends, dismantling blades, cleaning all dust, applying grease, filling cavaties with fillet, including reassembling blades and hanging ceiling fan after getting repaired and connecting up including provision of cable from ceiling rose to connector of fan, complete all as specified and directed.

All as per item No. 146 here-in-before but exhaust fans of any sweep.

All as per item No. 146 here-in-before but wall mounted fans/ Pedestal fans of any sweep.

Disconnect and remove unserviceable capacitor and Supply and fix capacitor 2.5 MFD suitable for ceiling fan / exhaust fan, complete all as specified and directed.

All as per item No. 150 above but of 4 MFD suitable for ceiling fan / exhaust fan, complete all as specified and directed.

Dismantle the unserviceable shackle assembly and supply and fixing new shackle assembly comprising GI bolts, nuts, rubber bush and split pin, complete all as specified and directed.

M&L for removing the defective fan winding and rewinding with super enamelled copper wire of existing gauge, applying insulation varnish, pre heating and binding with empire tubes, crimple sheet etc. as required for rewinding, complete all as specified and directed for the following:-

Ceiling fan of size upto 1400 mm sweep.

Wall mounted/ Pedestal fan of size upto 450 mm sweep.

Exhaust fan of size upto 300 mm Sweep.

Exhaust fan of size 350 to 450mm Sweep.

Disconnect and remove unsv PCB and supply and fix PCB suitable for BLDC Fan of 1200mm sweep of any make or model, complete all as specified and directed

M&L for remove unsv bearing and supply and fix bearing suitable for fan of 1200mm sweep of any make or model, complete all as specified and directed

Taking down unserviceable louvers and supply and fix new louvers suitable for exhaust fans of size upto 450 mm sweep, complete all as specified and directed.

Taking down the electric Geyser of capacity 25 ltrs/ 50 ltrs carefully from its installed position by disconnecting inlet and outlet water pipes, electrical connections,taking out the inner leaking copper tank, brazing the leaking portion of copper tank, testing for leaks, re-assembling the geyser including provision of additional glasswool as required, refixing in position, testing and reconnecting the inlet/ outlet water pipes and testing on completion, complete all as specified and directed.

Supply and fixing of following items in repairs, suitable for single phase, 230 Volts, 50 Hz for existing type electric Geyser of capacity 25/50 Litres incl taking down the old one :-

(a) Heating element 1500/2000 watts push/ thread type porcelain / Circular / triangular type as required at site.

(b) Thermostat as per the existing type.

(c) Indication lamp red/ green.

(d) Fusible plug

Taking down unserviceable PVC connection of any description and supply and fix new PVC connection 15mm dia 450mm long with brass nuts, and rubber washers on both sides suitable for cold/ hot water, complete all as specified and directed.

Taking down unserviceable PVC connection of any description and supply and fix new PVC connection 15mm dia 600mm long with brass nuts, and rubber washers on both sides suitable for cold/ hot water, complete all as specified and directed.

Taking down old UNSV DB and Supply and fixing Vertical distribution board for incoming MCCB upto 250 A and MCBs for outgoing to be used, VTPN 4 Way, 415 Volts having earth bar & neutral link double door as in repairs complete all as specified and directed. Note. MCCB and MCB will be measured and paid seperately under relevant items. Make Havells, HPL, Indo Asian, Standard, Legrand

Taking down old UNSV DB and Supply and fix in repair, MCB distribution board, double door type, TPN 4 way, sheet steel powder painted, with bus bar, neutral link & earth bar etc, including taking down existing DB complete all as specified and directed.

Taking down old UNSV DB & Supply and fix in repair, flush to wall, MCB distribution board, double door type, SPN 12 way, sheet steel powder painted, with bus bar, neutral link & earth bar etc, incl taking down existing DB complete all as specified and directed.

Taking down old UNSV DB & Supply and fix in repair, flush to wall, MCB distribution board, double door type, SPN 8 way, sheet steel powder painted, with bus bar, neutral link & earth bar etc, including taking down existing DB complete all as specified and directed.

Taking down old UNSV DB & Supply and fix in repair, flush to wall, MCB distribution board, double door type, SPN 4 way, sheet steel powder painted, with bus bar, neutral link & earth bar etc, including taking down existing DB complete all as specified and directed.

Taking down old UNSV Metal Clad enclosure & Supply and fix Single Pole & Neutral Metal clad enclosure with a two pin and earth plug and socket including one single pole MCB of 20 Amps in repair complete all as specified and as directed by Engineer-in-Charge

Taking down old UNSV MCCB & Supply & fix in repairs, MCCB 3 pole, 415V, Adjustable /fixed type, follwing size suitable for load line DBs with terminating cables by using lugs as required, complete all as specified and directed.

MCCB TP 125A, 16KA. fixed type

MCCB 3 Pole 25A to 100A, 16KA. fixed type

Taking down old UNSV MCB & Supply and Fix in repairs, MCB FP/ TPN, DP/ SPN, SP ''C'' curve, 415V, including provision of copper lugs for cable termination, terminating cables by using lugs as required, complete all as specified and directed.

MCB TPN/FP 16 to 32 Amp

MCB TP 25 To 63 AMP

MCB SPN 32 AMP

MCB SPN 40 to 63 AMP

MCB SP 5 To 32 AMP

MCB FP 40 to 100 AMP

Taking down exisiting service cable and supply and fixing 1100 volts grade, heavy duty cable, PVC insulated, stranded aluminium conductor, served with inner sheathing of PVC tape and overall PVC sheathed in service connections, one twin core cable of size 4.0 Sqmm, complete all as specified and directed.

Taking down exisiting service cable and supply and fixing 1100 volts gr. heavy duty cable, PVC insulated aluminium stranded conductor, served with inner sheathing of PVC tape and overall PVC sheathed in service connections, one twin core cable of size 6.0 Sqmm, complete all as specified and directed.

Taking down exisiting service cable and supply and fixing, 1100 volts gr. heavy duty cable PVC insulated stranded aluminium conductor, served with inner sheathing of PVC tape and overall PVC sheathed in service connections, one twin core cable of size 10 Sqmm, complete all as specified and directed.

Supply and fix electronic meters temper proof LCD display with polycarbonate cover Single phase, 230 V, 10 to 60Amp, accuracy class-I 50Hz, conforming to IS 13779, IP-54, with parameters to show data, time, current reading, load, PF, voltage and KWH complete including taking down old unsv electric meter complete all as specified and directed. Make: HPL Model:SPPB1321120000ME03 (Gurgaon) 'OR' equivalent in Secure, L&T , AE.

Taking down unserviceable multi-sensor (smoke & heat) and S&F Analog addressable type multi-sensor (smoke & heat) detector with dual optic's technology to distinguish and differenciate between real fire, steam and dust to avoid any false alarm & built-in isolator with multiple algorithms setting with base powder, including other accessories as required, complete all as specified and directed. Make: EST-3/Notifire/ Honey well/ Ravel

Servicing the Analog / Addressable type multi sensor fire alarm system by removing the faulty detectors, cleaning all the detector, ensuring the power supply and battery back up to the panel, minor repair to the power cord and cable, clearing all the faults, detected by the system and bring it to normal mode complete all as specified and directed by Engineer in Charge. Note. Replacement of detectors and battery will be measured and paid separately.

Servicing of solar geyser panel using mild cleaning agent, removing and replacing of rusted nuts and bolts with GI nuts and bolts, complete all as specified and directed.

Supply and replacement of geysor element, 3.0 KW, SP, suitable for Solar water heater backup including taking down the old element, complete all as specified and directed.

Supply and replacement of geysor element, 2.0 KW, SP, suitable for Solar water heater backup. including taking down the old element, complete all as specified and directed.

Disconnecting the electrical, water supply connections of Solar geyser, repairs to leaking Solar geyser inner tank by removing glass wool, cutting/disconnecting the rusted inlet and outlet nipples, supply and connect new nipples of size as existing by brazing/ welding, leak testing, refilling the glass wool including additional glasswool as required, fixing in position, testing and commissioning, complete all as specified and directed.

S&F in replacement electric water heater, vertical storage type with ferroglass coated anti-rust inner container and heating element upto 2 KW capacity 25 litre, heavy duty anode rod, preset thermal cutout, BEE 5 Star rated as per latest BEE norms (i.e. standing losses ≤ 0.465 kWh/24 hour/45°C which is only valid till 31st Dec 2025, material shall be supplied as per latest revision at the time of supply, complete with all accessories such as safety valve, thermostat, NRV, connection piece(hot and cold water connection pipe) etc including taking down the existing unserviceable geyser complete all as specified and directed by Engr-in-charge. Model: Havells Monza GHWAMOSWH025 or Crompton Arno Neo ASWH-3025 or similar

Supply and Fix , bed side night lamp, adjustable arm decorative type as per existing model fixed on wall complete on PVC base blocks and connecting with suitable size of flexible cable from connector all as specified and directed by Engineer-in-charge. Make : Philips/Halonix/Bajaj

Supply and Fix in repair, booster pump cylender (pressure tank) threading type suitable for pressure pump of capacity 0.5 HP 220 volt AC or existing type, including testing all as directed by Engineer-in-charge.

Supply and Fix in repair, booster pump Pressure switch threading type suitable for pressure pump of capacity 0.5 HP 220 volt AC or existing type, including testing all as directed by Engineer-in-charge. Model No. KP-35 Pressure switch of Danfoss or equivelent in ocean star/Amazor.

Rewinding of electrical motor(booster pump) by taking out burnt copper winding from stator, cleaning the casing & slots with wire brush & washing with water under pressure, cleaning with CTC, dried and rewinding the motor using same gauge of super enameled copper wire as existing & making the winding leak proof by applying warnish, drying etc. and re-connecting at its original position of capacity of motor upto 0.5 HP including testing of motor after installation for satisfactory functioning/running all as specified and as directed by the Engineer-in-charge.

PVC insulated Tape 20 mm width, 25 m length, assorted colour Make: Grippex or equivalent as approved.

S&F in replacement exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250mm including taking down the existing unserviceable fan and depositing it to MES E/M Store complete all as specified and directed by Engr-in-charge

S&F in replacement Exhaust fan, steel body AC Single phase 230 V of size 300 mm sweep with blades, and frame and louvers including taking down the existing unserviceable fan and depositing it to MES E/M Store complete all as specified and directed by Engr-in-charge

M&L for cutting round holes suitable using diamond cutter for fixing of exhaust fan/chimney pipe of size 150-300 mm into through stone walls built in cement mortar or cement lime mortar and making good in cement mortar 1:3 or cement concrete 1:2:4 type B1 as required and plastering in CM 1:4 external / internal surfaces and finished to match with the existing surfaces complete all as specified and directed by Engr-in-charge.

S&F in replacement wall mounted decorative light, 23W, body colour white complete all as specified and directed (Model: Philips comet 30575 or Havells stylo LHFOECE1TZ1O014 or similar)

S&F in replacement Ceiling fans, complete with three blade, down rod, accessories 230V, 1200mm sweep, with Squirrel cage induction motor, Non-BLDC, power consumption not to exceed 40W, BEE 3 star rated as per latest BEE norms including taking down the existing unserviceable fan and depositing it to MES E/M Store complete all as specified and directed by Engr-in-charge. Model: Havells ES40

Please Enable Macros to View BoQ information