REPAIR MAINTENANCE OF EOT HOT CRANES FIRE FIGHTING PUMP SET AND ALLIED WORKS AT ITR CHANDIPUR

Amount

NOTE (Applicable for all items) :- The bidders/contractors are advised to read tender document & all corrigendum / amendments and General conditions of contracts before entrying/quoting the rates.

PART-I (CRANE & LIFT):- Repairing / overhauling and servicing of EOT / HOT Cranes of 10 ton capacity with a span of 13.5 Mtrs , and a height of 10 mtrs from ground, including Repair/overhauling and servicing of Gear boxes, motor, thruster and couplings, resetting of brakes including replacement of Brackes shoes ,changing of all types of Lubricating oils/Greases etc of all LT & CT wheels and couplings , lubrication of Wire ropes with the help of Cardium compound , Servicing of cable carriers for power feeding and fistoon cables, fistoon structures, Modification, Panel Repairing and servicing, Hoist limit switch changing and setting , CT & LT limit Switch Re- Installation and Re-Setting and Electric Circuit Repair, Re- Installation and setting etc and dismantling and checking all serviceable/unserviceable parts, Cleaning the rusted/greasy surfaces of the overhead crane girder, travel and control panel, hook, steel wire rope etc complete by approved cleanser. After repairing/servicing the each parts of cranes, Re-fixing the same to its Original positions including all packing seals, nuts, bolts and washers etc complete all as required at site complete all as directed by Engineer-in-Charge. at Bldg No- 06 of LC-III area of ITR Chandipur. Note- (i) CT/LT Test and load test of Crane to be carried out after repairing. (ii) Load as required for testing be arranged by Contractor. (iii) Transportation of load for testing from the place of issue and return to the place of issue shall be responsibility of the contractor. (iv) Lubricants/GearOil/Transformer oil/Grease and necessery spares required for repair of unserviceable Cranes if any will be measured & Paid separately under respective item of this schedule as "Supplied only" items. against Schedule Ser Items No. 1.005 to 1.032. However, for servicing work, cost of minor spares to be replaced if any and not specified in this schedule viz. screws, washers, teflon seal, rubber bush, insulation tape, copper thimble, copper connecting jack, short length connecting wire, markers etc upto Rs 100 is deem to be included in the rate of the item. (v) Cost of taking down, reinstallation and transportation if required for the servicing / repair work is deem to be included in the price. 4. Servicing and repair work will be carried out within the contract period as and when required as per the site requirement and as directed by Engg-in-Charge.

Repairing / overhauling and servicing of EOT / HOT Cranes of 20 ton capacity with a span of 13.5 Mtrs , and a height of 10 mtrs from ground, including Repair/overhauling and servicing of Gear boxes, motor, thruster and couplings, resetting of brakes including replacement of Brackes shoes ,changing of all types of Lubricating oils/Greases etc of all LT & CT wheels and couplings , lubrication of Wire ropes with the help of Cardium compound , Servicing of cable carriers for power feeding and fistoon cables, fistoon structures, Modification, Panel Repairing and servicing, Hoist limit switch changing and setting , CT & LT limit Switch Re- Installation and Re-Setting and Electric Circuit Repair, Re- Installation and setting etc and dismantling and checking all serviceable/unserviceable parts, Cleaning the rusted/greasy surfaces of the overhead crane girder, travel and control panel, hook, steel wire rope etc complete by approved cleanser. After repairing/servicing the each parts of cranes, Re-fixing the same to its Original positions including all packing seals, nuts, bolts and washers etc complete all as required at site complete all as directed by Engineer-in-Charge. at Bldg No- 05 of LC-III area of ITR Chandipur. Note- (i) CT/LT Test and load test of Crane to be carried out after repairing. (ii) Load as required for testing be arranged by Contractor. (iii) Transportation of load for testing from the place of issue and return to the place of issue shall be responsibility of the contractor. (iv) Lubricants/GearOil/Transformer oil/Grease and necessery spares required for repair of unserviceable Cranes if any will be measured & Paid separately under respective item of this schedule as "Supplied only" items. against Schedule Ser Items No. 1.005 to 1.032. However, for servicing work, cost of minor spares to be replaced if any and not specified in this schedule viz. screws, washers, teflon seal, rubber bush, insulation tape, copper thimble, copper connecting jack, short length connecting wire, markers etc upto Rs 100 is deem to be included in the rate of the item. (v) Cost of taking down, reinstallation and transportation if required for the servicing / repair work is deem to be included in the price. 4. Servicing and repair work will be carried out within the contract period as and when required as per the site requirement and as directed by Engg-in-Charge.

Repairing / overhauling and servicing of EOT / HOT Cranes of 20 ton capacity with a span of 8.40 Mtrs , and a height of 10 mtrs from ground, including Repair/overhauling and servicing of Gear boxes, motor, thruster and couplings, resetting of brakes including replacement of Brackes shoes ,changing of all types of Lubricating oils/Greases etc of all LT & CT wheels and couplings , lubrication of Wire ropes with the help of Cardium compound , Servicing of cable carriers for power feeding and fistoon cables, fistoon structures, Modification, Panel Repairing and servicing, Hoist limit switch changing and setting , CT & LT limit Switch Re- Installation and Re-Setting and Electric Circuit Repair, Re- Installation and setting etc and dismantling and checking all serviceable/unserviceable parts, Cleaning the rusted/greasy surfaces of the overhead crane girder, travel and control panel, hook, steel wire rope etc complete by approved cleanser. After repairing/servicing the each parts of cranes, Re-fixing the same to its Original positions including all packing seals, nuts, bolts and washers etc complete all as required at site complete all as directed by Engineer-in-Charge. at Bldg No- 04 of LC-III area of ITR Chandipur. Note- (i) CT/LT Test and load test of Crane to be carried out after repairing. (ii) Load as required for testing be arranged by Contractor. (iii) Transportation of load for testing from the place of issue and return to the place of issue shall be responsibility of the contractor. (iv) Lubricants/GearOil/Transformer oil/Grease and necessery spares required for repair of unserviceable Cranes if any will be measured & Paid separately under respective item of this schedule as "Supplied only" items. against Schedule Ser Items No. 1.005 to 1.032. However, for servicing work, cost of minor spares to be replaced if any and not specified in this schedule viz. screws, washers, teflon seal, rubber bush, insulation tape, copper thimble, copper connecting jack, short length connecting wire, markers etc upto Rs 100 is deem to be included in the rate of the item. (v) Cost of taking down, reinstallation and transportation if required for the servicing / repair work is deem to be included in the price. 4. Servicing and repair work will be carried out within the contract period as and when required as per the site requirement and as directed by Engg-in-Charge.

Repairing / overhauling/Servicing and Greasing of EOT / HOT Cranes of 2 to 5 ton capacity with a Maximum span of 10 Mtrs , dismantling and checking all serviceable/unserviceable parts, Cleaning the rusted/greasy surfaces of the overhead crane girder, travel and control panel, hook, steel wire rope etc complete by approved cleanser. After repairing/cleaning and gresing of all the parts of cranes, re-fix the same to its original positions, alignment of shaft and coupling of all motors including all packing seals, nuts, bolts and washers etc complete all as required at site complete all as directed by Engineer-in-Charge. Note-(i) CT&LT, and load test of crane to be carried out after repairing. (ii) Load as required for testing be arranged by contractor. (iii) Transportation of load for testing from the place of issue and return to the place of issue shall be responsibility of the contractor. (iv) Cost is inclusive of all requisite spares and consumables for above repair except for those specified separately.

Supply only Geared Coupling for hoist drive of 20/10 Tone capacity crane having a spon of 13.5 mtrs and a height of 10 mtrs ,and all as specified and directed by engr - in Charge.

Supply only Torque spring for 18 KG Thruster of 20/10 Tone capacity crane having a spon of 13.5 mtrs and a height of 10 mtrs ,and all as specified and directed by engr - in Charge.

Supply only Brake shoes suitable for 10/20 Tone capacity crane having a spon of 13.5 mtrs and a height of 10 mtrs ,and all as specified and directed by engr - in Charge.

Supply only Hoist brake 160 mm dia suitable for 2 Tone capacity crane installed at same garder of 20 tone crane and having a spon of 13.5 mtrs and a height of 10 mtrs ,and all as specified and directed by engr - in Charge.

Supply Only Over hoist limit switch along with all accessories suitable for 10/20 Tone capacity crane having a spon of 13.5 mtrs and a height of 10 mtrs ,and all as specified and directed by engr - in Charge.

Supply only 2 KVA Transformer suitable for 10/20 Tone capacity crane having a spon of 13.5 mtrs and a height of 10 mtrs ,and all as specified and directed by engr - in Charge.

Supply only 3 pole power Contactor, 32 amps suitable for LT Panel of 10 Tone capacity crane having a spon of 13.5 mtrs and a height of 10 mtrs ,and all as specified and directed by engr - in Charge.

Supply only 3 pole power Contactor, 70 amps suitable for LT Panel of 10/20 Tone capacity crane having a spon of 13.5 mtrs and a height of 10 mtrs ,and all as specified and directed by engr - in Charge.

Supply only power Contactor, 32 amps suitable for LT Panel of 10/20 Tone capacity crane having a spon of 13.5 mtrs and a height of 10 mtrs ,and all as specified and directed by engr - in Charge.

Supply only 3 pole power Contactor, 70 amps suitable for LT Panel of 10/20 Tone capacity crane having a spon of 13.5 mtrs and a height of 10 mtrs ,and all as specified and directed by engr - in Charge.

Supply only of Over load relay for Cross Travel suitable for LT Panel of 10/20 Tone capacity crane having a spon of 13.5 mtrs and a height of 10 mtrs ,and all as specified and directed by engr - in Charge.

Supply only of Over load relay for Long travel suitable for LT Panel of 10/20 Tone capacity crane having a spon of 13.5 mtrs and a height of 10 mtrs ,and all as specified and directed by engr - in Charge.

Supply only Over load relay for hoist suitable for LT Panel of 10/20 Tone capacity crane having a spon of 13.5 mtrs and a height of 10 mtrs ,and all as specified and directed by engr - in Charge.

Supply only Over load relay for Creep suitable for LT Panel of 10/20 Tone capacity crane having a spon of 13.5 mtrs and a height of 10 mtrs ,and all as specified and directed by engr - in Charge.

Supply only Auxiliary Contact with Add on block suitable for LT Panel of 20/10 Tone capacity crane having a spon of 13.5 mtrs and a height of 10 mtrs ,and all as specified and directed by engr - in Charge.

Supply only Auxiliary Contactor with Add on block suitable for LT Panel of 20/10 Tone capacity crane having a spon of 13.5 mtrs and a height of 10 mtrs ,and all as specified and directed by engr - in Charge.

Supply only Timer KR TPN suitable for LT Panel of 10/20 Tone capacity crane having a spon of 13.5 mtrs and a height of 10 mtrs ,and all as specified and directed by engr - in Charge.

Supply only Terminal blocks suitablr for LT Panel of 10/20 Tone capacity crane having a spon of 13.5 mtrs and a height of 10 mtrs ,and all as specified and directed by engr - in Charge.

Supply only Hooter suitablr for 10/20 Tone capacity crane having a spon of 13.5 mtrs and a height of 10 mtrs ,and all as specified and directed by engr - in Charge.

Supply only Gear oil for 20/10/5 Tone capacity crane having a spon of 13.5 mtrs and a height of 10 mtrs ,and all as specified and directed by engr - in Charge.

Supply only Grease for 20/10/5 Tone capacity crane having a spon of 13.5 mtrs and a height of 10 mtrs ,and all as specified and directed by engr - in Charge.

Supply only Cardium compound for Rope of 20/10/5 Tone capacity crane having a spon of 13.5 mtrs and a height of 10 mtrs ,and all as specified and directed by engr - in Charge.

Supply only of transformer oil suitable for 20/10/5 tone capacity crane including drain out the unserviceable transformer oil . ( Make :GULF/POWER OIL/HP)

Supply only Thruster oil for 20/10/5 Tone capacity crane having a spon of 13.5 mtrs and a height of 10 mtrs ,and all as specified and directed by engr - in Charge.

Supply only Pedant Push switch suitable for 20/ Tone capacity crane having a spon of 13.5 mtrs and a height of 10 mtrs ,and all as specified and directed by engr - in Charge.

Supply only EPR Insulated copper conductor 10 Corex 2.5 Sqmm suitable for 20/10/5 Tone capacity crane having a spon of 13.5 mtrs and a height of 10 mtrs ,and all as specified and directed by engr - in Charge.

Supply only Over load relay for Hoists suitable for 20/10/5 Tone capacity crane having a spon of 13.5 mtrs and a height of 10 mtrs ,and all as specified and directed by engr - in Charge.

Supply only Over load relay for Creep suitable for 20/10/5 Tone capacity crane having a spon of 13.5 mtrs and a height of 10 mtrs ,and all as specified and directed by engr - in Charge.

M&L for spray painting to complete EOT / HOT Cranes of 10 to 20 ton capacity with a maximum span of 18 Mtrs and a maximum height of 10 mtrs, complete including preparing the surfaces by all suitable means by removing the old paint with sand paper and spray painting the complete parts of crane with one coat of approved synthetic enamel paint and writing machine No with synthetic enamel paint different from crane body colour on the crane complete all as directed by Engineer-in-Charge. Make :- Asian paint or any others equivalent paints

M&L for spray painting to complete EOT / HOT Cranes of 2 to 5 ton capacity with a maximum span of 18 Mtrs and a maximum height of 10 mtrs, complete including preparing the surfaces by all suitable means by removing the old paint with sand paper and spray painting the complete parts of crane with one coat of approved synthetic enamel paint and writing machine No with synthetic enamel paint different from crane body colour on the crane complete all as directed by Engineer-in-Charge. Make :- Asian paint or any others equivalent paints

M&L for Earthing in repair complete with galvanised steel earth plate electrode 60 cm x 60 cm x 6 mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5 metres below normal ground level connected to galvanised iron strip 25 mm x 4 mm as earth lead by means of bolts, nuts, check nuts & washers etc, GI earth lead strip duly protected by and including 40 mm dia GI pipe (light grade) and 20 mm GI pipe (medium grade) for watering and connected to control switch as directed including necessary earth work in soft /loose soil and disposal of excavated soil to a distance not exceeding 50 m, PCC(1:3:6) type C1 as in concrete pit, 50 mm thick precast RCC (1:1.5:3) type A1as in cover slab duly reinforced with 8 mm dia TMT bar @ 100 mm c/c both way and two nos lifting handle made cut of 10 mm dia TMT bar and set in cement mortar (1:4) , funnel, and salt , in alternate layer, testing etc complete and as specified in Electrical Plate No 3 of SSR Part-I including taking down old earthing pit.

Supply and fix in repair Ggalvanized Iron (GI) strip 25 x 4 mm burried in ground / passing through pipe complete all as specified and as directed .

S&F in repair indicator lamp suitable 110 volts coils of any make suitable for 2 to 20 ton capacity EOT crane main hoist .

Comprehensive maintenance of lift of capacity one Ton serving for Ground floor plus two floors by replacing the trailing cable, checking of all power wiring termination, upper and lower limit switches for proper connection, Checking / adjusting guide clamp, Check all the locks functioning properly mechanically and electrically after opening the covers, check all sets of screws and spring and replace where necessary so that the lever should lock the brake properly for smooth operation of lift , Repair/maintenance of all door shutters of lift serving for G+2 floors by repairing / replacing minor unserviceable parts, complete greasing and carrying out door adjustment, guide clamp adjustment, locking system etc. for smooth functioning of all door Shutters complete and all as specified and directed by Engineer-in-Charge.

Supply and fixing in repair Door sensor suitable for 1 Tone capacity Lift and all as specified and directed by Engr - in - Charge.

Supply and fixing in repair ARD battery suitable for 1 Tone capacity Lift and all as specified and directed by Engr - in - Charge.

Supply and fixing in repair Push botton LOP & COP Suitable for 1 Tone Lift and all as specified and directed by Engr - in - Charge.

Repair / overhauling , Gear box of 1 Ton capacity lift by skilled lift mechanic and Machinist by dismantling all the mechanical components, cleaning, remetalling, cutting, polishing of gear teeth and making as per original shape complete. Remetalling of driving shaft, machining, finishing, polishing for smooth running. Replacing the unserviceable oil seal, bushes, bearings of driving and non-driving end. Re-fixing all the components after necessary repair works. Replacing/top up of the gear oil in the gear box up to required level. Making adjustment to ensure trouble free and smooth running of gear system complete all as directed by Engineer-in-Charge.(Note : Cost is inclusive of all requisite spares and consumables, gear oil etc)

PART-II (FIRE FIGHTING PUMPSETS ALLIED WORKS) Dismantling and taking down electric motor of fire pumpset assembly and transporting to workshop and carrying out servicing / maintenance of motor unit of capacity 75 KW 3 phase,415 Volt, as per the following scope of work :- (a) Opening of electric motor assembly and cleaning & remvoing of dirt / dust etc from armature and field coil. (b) Cleaning and checking of stator and rotor unit. (c) Checking and tightening of coupling bolts and replacement of rubber inserts. (d) S/F DE and NDE bearings including taking out of unserviceable bearings. (e) M&L for carrying out heat varnishing with best quality varnish solution to field and armature coil and keeping in heating chamber for 48 hours for drying up properly. (f) Reassembling of complete motor and carrying out testing at workshop, transportation back to installation and coupling with pump set including making necessary alignment, cable connections including testing on load all as specified and directed.

Disconnecting and taking out the electric driven Jockey pump Motor of capacity 18.5 KW (Kirloskar make), discharge capacity 500 LPM at 7.5 kg/sqcm by disconnecting the pump motor coupling, inlet and outlet pipe line for foundation. Repair to Motor by replacement of worn out, coupling and bearing, repairing of worn out spare parts and rewinding of motor assembly, reassembling the motor after repairs, including replacement of all nuts, bolts, washers, gland packing, greasing etc and fixing the motor in its original position / foundation and testing on load complete and all as directed and as specified.

Disconnecting and taking out the electric driven Jockey pump of capacity 18.5 KW (Kirloskar make), discharge capacity 500 LPM at 7.5 kg/sqcm by disconnecting the pump motor coupling, inlet and outlet pipe line for foundation etc. Repair to pump by replacement of worn out gland cap, gland bush, coupling and bearing, repairing of worn out shaft, impeller by suitable re-metalling, finishing up to suitable size and doing necessary heat treatment, replacement of impeller key with new one including necessary heat treatment, reassembling the pump after repairs, including replacement of all nuts, bolts, washers, gland packing, greasing etc and fixing the pump in its original position / foundation and testing on load complete and all as directed and as specified.

S&F in repair MS Pipes heavy grade with all fittings laid in floors or fixed to walls and ceilings etc of sizes 200 mm dia including cutting, welding etc.

S&F in repair MS Pipes heavy grade with all fittings laid in floors or fixed to walls and ceilings etc of sizes 100 mm dia including cutting, welding etc.

S&F in repair MS Pipes heavy grade with all fittings laid in floors or fixed to walls and ceilings etc of sizes 80 mm dia including cutting, welding etc.

S&F in repairs 25 mm dia GI pipe, heavy grade, with all fittings laid in floors or fixed to wall complete all as specified and directed.

S&F in repair gun metal gate valve of 25 mm dia .

S&F in repair fire hydrant delivery hose reel with coupling of 30 m length and suitable Diameter.

S&F in repair hose box made of 18 gauge MS Sheet 800mm x 600mm x 250mm, double door with 4 mm thick glasses and door frame made of 16 gauge MS sheet painted fire red out side and brilliant white inside and all as directed.

S&F in repairs cast iron special fittings bends (any type, radius and angle) tapers any type (straight, bend, increasing, decreasing or double socket etc) tee pieces single branch 'Y' junction, double branch, cross (all fittings for spigot and socket pipes) collars caps and plugs of any size etc.

M&L PCC (1:3:6) type C2 (using 40mm graded stone aggregates) for foundation, filling and mass concrete.

S&F in repair Sluice valve with brass spindle PN 1.6 of size 150 mm. MAKE-KIRLOSKAR/UPADHAYAY.

S&F in repair Sluice valve with brass spindle PN 1.6 of size 100 mm. MAKE-KIRLOSKAR/UPADHAYAY.

Supply and fix 3 pole Power Contactor type MNX40 conforms to IS/IEC60947-4-1 & IEC60 947-4-1 415 volt AC, 3 Ph of capacity 140Amps in AC3 including taking down old U/S power contactor and carrying out of servicing and resetting of Motor Starters all as directed. Power Contactor Make-L&T of Cat no-CS94138/C&S Cat no.-LC1FDP150A or equivalent in BCH

S&F in repair Steel Chequered Plates channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment and as per site requirements using Fe 410-W (Gde-E-250) quality-A steel.

M&L for painting to LT Control panels and exposed pipe lines of steel / iron surfaces of any description, over 10 cm in width or girth, not otherwise described after preparation of old painted surface, with one coat of red oxide primer and two coats of synthetic enamel paint as per colour code and all as directed and approved.

S & F in repair LED Panel indicator lamp of any type to match with existing and of colour Red, Yellow, Blue. 22 mm DIa Make-C&S/L&T

S&F in repair digital voltmeter suitable for 3 phase AC supply,CT/PT site programmable, 96x96 mm size,class1(Make-L&T Cat Part No-WL132010OOOO or equivalent)

S&F in repair digital ammeter suitable for 3 phase AC supply,CT/PT site programmable,5A,class1, 96x96 mm size,class1(make-L&T Cat Part No-WL131010OOOO or equivalent)

S&F pressure gauge 100 mm dia type 10 Kg/sqcm. including taking down old u/s pressure gauge. Make-RMCO or equivalent as approved.

M&L for wiring with PVC insulated FR cable with stranded copper conductor 4x16 sqmm drawn in and including existing PVC/Metallic conduit including laying of copper cable for connection between Pumpset and motor starter including taking out of old unserviceable cable connection of any type and all as directed and as specified.

S&F in repair STAR- DELTA timer, Timing Range 3 Sec-120 Sec, Voltage 24-240 VAC/DC, Cat No. - 2ASDTO Make Equivalent

S&F in repair MN12 O/L Relay 90-150 A, Make L&T Cat No.- SS94138OOMO Or Equivalent

S&F in repair Adaptor Ring (For 30 to 20 mm in Panel cutout conversion Make: L&T Cat no. HH180000 Or Equivalent

S&F in Repair contactor MNX 80 A,240 V Cat No.CS97077BOOO L&T Or Equivalent

S & F In repair left side add on block 1NO+1NC Cat No. CS94201OOOO L&T Or Equivalent

S & F In repair Right side add on block 1NO+1NC Cat No. CS94202OOOO L&T Or Equivalent

S&F in Repair MCCB DN0-100 C TP 63A,25KA Cat No. CM91612OOHOOG L&T Or Equivalent

S&F in Repair Auxiliary contactor MX022E 2NO+2NC Cat No. CS94020BOOO L&T Or Equivalent

S&F in repair MN5 O/L relay 30-5- A Cat No.SS94136OOGO L&T Or Equivalent

Cleaning and Repairing of Fire Static Tank of capacity 50000 Gln for fire fighting system by draining out the water and taking out the sludges from the bottom of the static water tank and cleaning mossy on the walls of the tank and scrapping by wire brush and brooms, repairing the erroded surface surface with cement plaster and applying two coats of while lime and writing the date of cleaning on white paint over black painted surface complete all as specified and directed

Cleaning and Repairing of Fire Static Tank of capacity 30000 Gln for fire fighting system by draining out the water and taking out the sludges from the bottom of the static water tank and cleaning mossy on the walls of the tank and scrapping by wire brush and brooms, repairing the erroded surface surface with cement plaster and applying two coats of while lime and writing the date of cleaning on white paint over black painted surface complete all as specified and directed

Cleaning and Repairing of Fire Static Tank of capacity 20000 Gln for fire fighting system by draining out the water and taking out the sludges from the bottom of the static water tank and cleaning mossy on the walls of the tank and scrapping by wire brush and brooms, repairing the erroded surface surface with cement plaster and applying two coats of while lime and writing the date of cleaning on white paint over black painted surface complete all as specified and directed

Cleaning and Repairing of Fire Static Tank of capacity 10000 Gln for fire fighting system by draining out the water and taking out the sludges from the bottom of the static water tank and cleaning mossy on the walls of the tank and scrapping by wire brush and brooms, repairing the erroded surface surface with cement plaster and applying two coats of while lime and writing the date of cleaning on white paint over black painted surface complete all as specified and directed

S&F in Repair Fully automatic starter MN 80 FASD,90 HP, 67.5 KW, Relay range 45-75 Amp. Make :- L&T Cat No. SS94705 DOJO And its equivalent

Supply, installation, testing & commissioning of fire hydrant gun metal single outlet landing valves type A (single head outlet) ISI marked (IS-5290) for fire brigade complete all as specified & directed.

M/SNeelachal Enterprises

M/S T.N.CONSTRUCTION

DS ENTERPRISES

RPL SYNDICATE CO

ELECTRO COMMERCIAL CO

Bidder Name

DS ENTERPRISES

RPL SYNDICATE CO

KRISHNA ENTERPRISES

M/S T.N.CONSTRUCTION

ELECTRO COMMERCIAL CO

M/SNeelachal Enterprises