Construction of R.C.C (Ground floor) Training Centre including water supply and sanitary and electrical works at Training Centre Demow, Sivasagar

Amount

Earthwork in excavation for foundation trenches of walls, retaining walls, footings of column, steps, septic tank etc. including refilling (return filling) the quantity as necessary after completion of work, breaking clods in return filling, dressing, watering and ramming etc. and removal of surplus earth with all lead and lifts as directed and specified in the following classification of soils including bailing out water where necessary as directed and specified.(A) Up to a depth of 2.00m below the existing ground level.(a) In ordinary soil

Earth/ sand filling in plinth in layers not more than 150mm thick including necessary carriage, watering, ramming etc. complete as directed and specified including payment of land compensation, forest royalty, sales tax and other duties and taxes as may be necessary.(c) With river sand or silt (predominantly non plastic) by truck carriage including loading and unloading.

Raising low site around the building with approved soil obtained from outside by truck carriage including breaking clods, dressing etc. complete including paying necessary forest royelty, sales tax, land compensation, municipal gate fees, if any monopoly duty etc. (profile measurement to be taken and 12.5% deduction for shrinkage to be made from total quantity) etc. complete as directed and specified.(b) Other than Guwahati city

Plain cement concrete works with coarse aggregate of sizes 13mm to 32mm in foundation bed for footing steps, walls, brick works etc. as directed and specified including dewatering if necessary, and curing complete (shuttering where necessary shall be measured and paid separately).(b) In prop 1cement: 4 sand :8 coarse aggregate by volume

Plain cement concrete apron in prop 1:4:8 with 20mm down graded coarse agg. Over soling including neat cement finish using cement slurry 2.75Kg. of cement per sq.m. of floor (soling to be measured separately). (b) 50mm thick

Providing and laying plain/reinforced cement croncrete works cement, coarse sand & 20mm down graded stone aggregate including dewatering if necessary, and curing complete but excluding cost of form work and reinforcement for reinforced cement concrete work (form work and reinforcement will be measured and paid separately) Foundation, footing, columns with base tie and plinth beam, pile cap, base slab, retaining walls, walls of septic tank, inspection pit and the like and other works not less than 100mm thick up to plinth level.b) M20 grade concrete or Prop. 1:1.5:3

) Columns, pillars, posts, struts, suspended floor, roof, landing, shelf and support, balcony, lintel, sill band, beam, girder, bressumer, cantilever, staircase (except spiral staircase and landing ) including preparing the top surface and finishing of nosing.b) M20 grade concrete or Prop. 1:1.5:3

Providing and laying 25mm thick damp proof course with cement concrete in prop 1:1.5:3 with graded stone agg. of 10mm down nominal size including providing approved damp proof admixture in proportion as recommended by the manufacturer including curing etc. complete as directed.

Providing form work of ordinary timber planking so as to give a rough finish including centering, shuttering, strutting and propping etc., height of propping and centering below supporting floor to ceiling not exceeding 4.0M and removal of the same for in-situ reinforced concrete and plain concrete work in:Foundation, footings, bases of columns, pile cap, raft and mass concrete works etc.(i) Using 38mm thick plank

Providing form work of ordinary timber planking so as to give a rough finish including centering, shuttering, strutting and propping etc., height of propping and centering below supporting floor to ceiling not exceeding 4.0M and removal of the same for in-situ reinforced concrete and plain concrete work in: Columns, Pillars, Posts & Strut (a) Square, Rectangular, polygonal in plan or any shape like Tee/L etc. having plane vertical face (i) Using 38mm thick plank

Providing form work of ordinary timber planking so as to give a rough finish including centering, shuttering, strutting and propping etc., height of propping and centering below supporting floor to ceiling not exceeding 4.0M and removal of the same for in-situ reinforced concrete and plain concrete work in: Sides and Soffits of Beams, beam haunchings, cantilever girders, bressumers, lintels and horizontal ties. (i) Using 38mm thick plank

Providing form work of ordinary timber planking so as to give a rough finish including centering, shuttering, strutting and propping etc., height of propping and centering below supporting floor to ceiling not exceeding 4.0M and removal of the same for in-situ reinforced concrete and plain concrete work in: Foundation, footings, bases of columns, pile cap, raft and mass concrete works etc. (i) Using 38mm thick plank

Providing brick soling in foundation and under floor with stone/ best quality picked jhama brick, sand packed and laid to level and in panel after preparing the subgrade as directed including all labour and materials and if necessary dewatering, complete.(a).Brick on flat soling.

Brick work in cement morter with 1st class brick including racking out joints and curing complete as directed.(I) In Sub-structure upto plinth level including dewatering if necessary (c) In proportion 1:5.

1st class brick nogged wall in cement mortar including racking out joints and curing complete as directed in super structure above plinth up to 1st floor level (protruding M.S rod/Tor steel of column to be embeded in cement mortar and will be measured and paid separately) (A) 112mm thick brick wall (a) In cement mortar in proportion 1:4. (1 cement:4 sand)

Cement concrete works in topping 1:1:2 (1cement :1sand :2 graded aggregates on R.C.C floor, tread and rise of steps finished with a floating coat of neat cement using cement slurry for bond @ 2.75 kg.of cement per sq. m. of floor to be laid in panels including curing complete as directed (b) 20 mm thick

Providing VITRIFIED floor tiles of approved quality of specified size, shape and thickness not less than 18mm on floors, skirtings, risers and treads of steps over 15 mm thick base of cement mortar in prop. 1:3 (1 cement : 3 coarse sand ) including cutting where necessary finished with flush pointing with Fix-A-Tile (Choksey/Sika/Pedelite/Rouf) / white cement slurry mixed with approved pigment to match shade of tiles, mixed with approved pigment to match the shade of the tiles, complete at all levels as specified and directed. (Coloured pigment should be in conformity with colour of tiles and as approved and directed by the Department) a) Normal range Somany/ Orient/Nitco /Varmora/VITA/ Marbito/ Make ii) Of size 600mmx600mm and above

Providing polished ceramic wall tiles of approved quality, size, shape and thickness not less than 8mm on walls and skirtings over cement mortar bed 10 mm thick in prop. 1:3 (1 cement : 3 coarse sand ) including cutting where necessary finished with flush pointing with Fix-A-Tile (Choksey / Sika / Pedelite / Rouf) /white cement slurry mixed with approved pigment to match shade of tiles complete at all levels as specified and directed. (Cement plastering to be measured and paid separately). (Coloured pigment should be in conformity with colour of tiles and as approved and directed by the Department). (Walls means both interior and exterior walls). a) Normal range Somany/ Orient/Nitco/Asian Make ii) Of size 200mmx300mm and above

Providing polished granite tiles of approved quality, size, shape and thickness not less than 18 mm on floors, skirtings, risers and treads of steps over 15 mm thick base of cement mortar in prop. 1:3 (1 cement : 3 coarse sand ) including cutting where necessary finished with flush pointing with Fix-A-Tile (Choksey/Sika/Pedelite/Rouf) / white cement slurry mixed with approved pigment to match shade of tiles, mixed with approved pigment to match the shade of the tiles, complete at all levels as specified and directed. (Cement plastering to be measured and paid separately). (Coloured pigment should be in conformity with colour of tiles and as approved and directed by the Department) (i) With Fix-A-Tile (Choksey/Sika/Pedelite/Rouf)

Providing Antiskid Tiles of approved quality size, shape not less than 8mm on floor, skirting over a cement mortar bed 15mm thick of 1:3 (1 cement: 3 coarse sand) approved make fix with Fix-A-Tile (Choksey/Sika/Pedelite/Rouf)/ white cement complete at all level as specified and directed.(A) CERAMIC i)Normal range (Sizes 300 mm x 300mm and above)

Providing SUN ROCK HIGH CTS/DEVI paver block/tiles of concrete grade M30 or above of approved quality, size, shape of specified thickness over a levelling bedding layer of 30mm compacted sand over a base course of WBM or PCC (Base course to be paid separately) including cutting where necessary finished with spreading, sweeping jointing sand and compacting the pavers using compactor as specified and directed. SUN ROCK HIGH CTS / Devi Tiles (Pavers)(a) 80 mm thick

Red oxide plaster skirting with top layer of 5 mm thick cement plaster of cement mix using 3.5 kg. red oxide of iron per 50kg of cement in proportion 1:3 (1 cement: 3 coarse sand) finished with a floating coat of cement red oxide mix of same proportion. (b) 20 mm thick with under layer of 15 mm thick cement plaster.

15 mm thick Cement plaster in single coat on single or half brick wall for interior plastering up to 1st floor level including arises, internal rounded angles, not exceeding 80mm girth and finished even and smooth including curing complete as directed. b) In cement mortar 1:4

Providing wood work in frame (chowkaths) of doors, windows, clerestory windows and other similar works wrought, framed and fixed in position in contact with C.C or brick masonry wall including supplying, fitting and fixing with M.S. hold fast (40mmx3mmx250mm) as per design embeded in cement concrete block in proportion 1:2:4 and with two coats of kiricide oiling to the timber faces in contact with C.C and masonry as directed and specified. (b) With 1st class timber (Bonsum/ Sundi)

Providing, fitting and fixing full panelled doors/ windows including oxidised M.S butt hinges (100mm x75 mm x3.55mm) with necessary screws (other fittings to be measured and paid separately ) B) With 1st class local wood (Gamari/Hollock/Bonsum )(ii) 35 mm thick.

Providing, fitting and fixing M.S. grill of required pattern for windows/ clerestory windows/ openingwith M.S. flats at required spacing in frame all round, squre or round M.S. bars with round headed bolts and nuts or screws.I . Plain grill (c) Fixed to Brickwork/P.C.C/R.C.C.

Providing, fitting and fixing anodised aluminium sliding windows and ventilators of standard sections of approved brand without horizontal glazing bars, joints mitred and welded (manufactured to relevant IS specifications) and providing and fixing handles, angle cleat, rubber gasket, roller, bolting device, locking arrangements, screws etc as required complete as specified and directed for all levels.(b)3 Track sliding window (ii)5mm frosted glass

Providing, fitting and fixing anodised aluminium windows and ventilators of standard sections of approved brand without horizontal glazing bars joints mitred and welded (manufactured to relevant IS specifications) fitted with 6mm x 3.15mm lugs 100mm long embedded in CC blocks 150mm x 100mm x 100mm in 1:3:6 mix including providing and fixing handles, frictions stays, joining cleat, bolting device, locking arrangement, spring catch as required complete as specified and directed for all levels. (Cement concrete to be measured and paid separately). a)Side hung and Top hung windows and ventilators (ii)5mm frosted glass

Providing, fitting and fixing PVC door frame of Duroplast make DPF-5060 make suitable for DPS-3720 made from extruded PVC multichamber hollow section having dimensions of 50mmx60mm (Toletance + 1mm). Horizontal and vertical sections shall be joined by steel screws after inserting M.S. tubular rectangular galvanised L-shaped brackets of size 100mmx100mm or plastic brackets of size 75mmx75mm with metred cut at the corners. Hinge side of the frame shall be reinforced with M.S.Tubular section of size 40mmx20mm. The frame will be fixed to the column/ stiffner/ wall with the help of 3 nos 75mm long and 4mm dia steel screws and expandable fastners on each side of the door frame complete in all respects as sepcified and directed at all levels.

Providing, fitting and fixing PVC Door shutters of 37mm (single panel seamless finish) of Syntex make, at all levels made of extruded sections in the configuration of 'A'.The overall dimension is 37mm x 90mm, with usual process variation having a wall thickness of 2mm with a variation of +0.03mm provided with all plastic reinforcement to avoid rusting. The shutter frame is mitred and joined at the corners by means of stainless steel screws.The corners of the shutter frame are being reinforced by polymeric reinforcement of the size 125mm x 250mm and the lock rail is reinforced by 45 x18 x255 size reinforcement.

Providing two coats of Birla White Wall Care Putty (Water Resistant White Cement based putty for concrete/ mortar walls and ceiling both internal and external) after removing all loosely adhering material from the wall surface with the help of emery stone, putty blade or wire brush and moistening the wall with sufficient quantity of clean water as specified and directed by the department. (Total thickness of two coats is maximum 1.5mm)(ii)Thickness = 1.0mm thick

a) Applying one coat of cement primer of approved brand and manufacture on new wall surface after throughly brooming the surfaces free from mortar droppings and other foreign matter and including preparing the surface even and sand papered smooth.

Wall painting (two coats) with Plastic emulsion paint of approved brand and manufacture (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac) on new surface to give an even shade after throughly brushing the surfaces free from mortar droppings and other foreign matter and sand papered smooth. (a).Plastic Emulsion Paint of approved brand and manufacture (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac)

Applying primary coat over new steel and other metal surface over 100m in width or girth after preparing the surface by throughly cleaning oil,grease, dirt and other foreign matter and scoured with wire brushes, fine steels, wood scrapers and sand paper.a). With ready mixed "red-lead/ red oxide" primer.

Painting two coats (excluding priming coat) on new steel and other metal surface with enamel paint of approved brand and manufacture(Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac) to give an even shade including cleaning the surface of all dirt, dust and other foreign matter.b). High gloss (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac).

Applying priming coat over new wood and wood based surfaces over 100mm in girth/width after and including preparing the surface by throughly cleaning oil, grease, dirt snd other foreign matter , sand papering and knotting. (b). With ready mixed paint , wood primer (white).

Painting two coats (excluding priming coat) on new steel and other metal surface with enamel paint of approved brand and manufacture(Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac) to give an even shade including cleaning the surface of all dirt, dust and other foreign matter.b). High gloss (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac).

Supplying, fitting, fixing anodised aluminium fittings of approved make, resonably smooth, free from sharp edges and corners, flaws and other defects and with counter sunk holes for screws including necessary aluminium screws etc. complete.( anodised to bright natural matt & satin finished ) a) Sliding door boltsi) 300mm x 16mm

b) Tower bolts i) 300mm x 12mm

c) Door handles iii) 150mm

e) Butt hinge iv) 100mm x 63mm x 3.2mm

l) Hydraulic door closure

Supplying, fitting and fixing in position reinforcement bars conforming to relevant I.S. Code for R.C.C. work/ R.B. walling including straightening, cleaning, cutting and bending to proper shapes and length as per details, supplying and binding with 20G annealed black wire and placing in position with proper blocks, supports, chairs, spacers etc. complete.(No extra measurement for lap, hook, chair, anchor etc. will be entertained in the measurement as they are included in the rate) (Upto 1st floor level) a) From Primary Producer: TATA/SAIL/ Jindal steel/Shyam steel/RINL(i) TMT Corrosion resistant steel (CRS) reiforcement bar

Providing and fixing rolling shutters of approved make made of 80mm wide M.S. laths interlocked together through their entire lenth and jointed together at the ends by end-locks mounted on specially designed pipe shaft with bracket plates, guide channels and arrangements for inside and outside locking with push-pull operation complete including cost of wire, spring and hood cover for the shutters.

Providing and fixing Stainless Steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer in-charge.(For payment, only weight of Stainless Steel member is to be considered. No extra payment for fixing accessories such as nuts, bolts, fasteners etc. will be considered)

Providing drain with brick work in cement mortar in proportion 1:5 with half brick thick side walls and 100mm thick C.C (1:3:6) base over one brick flat soling including 15mm thick cement plastering in prop. 1:3 finished with a floating coat of cement slurry as directed with necessary shttering for sides and earth work in excavation of foundation trenches and refilling the sides after completion of work etc. as specified.ii). 300mm wide and average 250mm deep with bed slope 1 in 150 with initial depth of 100mm.

Surface dressing of ground including removing vegitation and/ or undulation of ground not exceeding 150mm deep and disposal of rubbish outside the periphery and lift up to 1800mm in all kinds of soil.

Pre construction anti - termite treatment at the bottom of foundation pits and walls on either side up to a height of 300mm from bottom of the excavation made for column plinth beam, wall, trenches etc. by applying the emulsion @ 5 (five) litres per square meter of the surface area before starting construction work (supplying of necessary tools and accessories by the contractor) as per the direction of the Department complete.a) with aqueous emulsion having concentration 1:19 with chloropirophose solution (tricel or euivalent) and water, i.e. 1% solution.

112 mm thick reinforced brick wall in prop 1:5 reinforced with two lines of M.S rod/ Tor steel as specified embeded in 38 mm thick concrete course in prop.1:2:4 with coarse agg. 12mm down at every fourth courses embeded with protruding rod in column including curing etc.complete as directed ( M.S rod/Tor steel shall be measured and paid separately) in super structure above plinth up to 1st floor level.(b). In proportion 1:4.

Cement plaster skirting with cement mortar in prop. 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement including rounding of junctions with floor.(b) 20 mm thick

Providing precast R.C.C slab over drain ,septic tank etc. in prop. 1:2:4 reinforced with 10mm M.S. bar @ 150mm centre both ways tying with 20 gauge black annealed wire with necessary shuttering , curing etc. complete including fixing in position as directed.b) 75mm thick slab

Supplying fitting and fixing white vetreous water closet squatting pan (Indian type pattern water closet) of size 580 x 240mm with 100mm SCI P or S traps of Parry ware / Hinware / Ceramake with all fittings and fixing complete including curing and making good the walls and floor wherever required a) white i) Parryware make

Supplying, fiting and fixing PVC flushing cistern with all internal fittings with CI brackets including fitting and fixing standard size CP flush pipe, union clamps etc. compete as directed and specified (pipes will be measured separately)a) white i) Parryware make

Providing fitting and fixing vitreous china flat back type lipped front urinal basin with standard flush pipe and CP brass spreader andbrass unions, etc. complete including painting of fittings and brackets, cutting and making good the walls & floors wherever required.a) white i) Parryware make

Supplying, fitting and fixing 87.5 degree P.V.C bend of ( Supreme / Prince ) or other I.S.I approved including joining, fitting and fixing etc. as necessary complete at all levels including below G.L as directed and specification.(ii) 110mm dia.

Supplying fitting and fixing PVC coupler of (Supreme / Prince) or other ISI approved including joining, fitting and fixing etc. as necessary complete at all levels including below G.L as directed and specified.(a ) In exposed surface or in trench(a) 110mm dia

(b) Concealed by chiselling or breaking brick wall / C.C / R.C.c and making good to the damaged (a) 110mm dia

Supplying fitting and fixing PVC cross "T" with door of (Supreme / Prince) or other ISI approved including joining, fitting and fixing etc. as necessary complete at all levels including below G.L as directed and specified.(a ) In exposed surface or in trench(i) 110mm x110 mm

Supplying fitting and fixing PVC pipes of 6 Kg /cm2 (Supreme / Prince) or other ISI approved including joining, fitting and fixing etc. as necessary complete at all levels including below G.L as directed and specified.(a ) In exposed surface or in trench ( (ii) 110mm dia

Supplying fitting fixing 75mm dia PVC cowel of ISI make complete as directed and specified as follows.

Providing fiting & fixing C.I. Grating to the floors complete as directed and specified. (ii) 110mm dia

Providing vitreous China wash basin with CI/MS brackets, C.P brass chain with plug,PVC waste pipe including painting of fittings and brackets, cutting and making good the walls wherever required. (Pillar cock, stop cocks, waste coupling are to be paid sepa rately)Basin (without pedestal) (A) Parryware Make (a) White (i) Star Basin 550 x 400 (Cat. No.C0450)

Providing fitting & fixing stainless steel kitchen sink of Parryware make with CI/MS brackets, C.P. brass chain with rubber plug, PVC waste pipe etc. complete including painting the fittings ,cutting &making good the walls wherever required. (Sink cock, stop cocks, waste coupling are to be paid separately (A) Parryware Make (i) Single Bowl with Veg Bowl & Drain Board (400 x 200) Flat Edge- Glossy (Cat.No.C8545)

Construction of filter bed in soak pit including earth work in excavation of soil and then filling up of the trench with brick bats / charcoal covered with earth over a layer of A.C plain sheet above brick bats filling complete as directed (size of soak pit may vary depending on the size and capacities of septic tank as well as the number of users as mentioned in the table)

Construction of inspection pit inside measurement 450mm x450mm x450mm flush with 100mm diameter HCI/PVC pipes and cement concrete base in proportion 1:3:6 over flat brick soling, 12cm brick wall in cement mortar in proportion 1:4 finished with 13mm cement plaster in proportion 1:2 in side wall and floor. 450mm x450mm air tight C.I. inspection pit cover and frame complete including supplying of materials, necessary excavation of pit as directed.

Labour for test boring with 40mm (internal) dia G.I. Pipes including keeping surplus of earth and every 2.00m after first 3.00m depth and delivering the same in nearest P.W.D. camp in the small tin container (container, scaffolding, tools etc. will have to be arranged by the contractor at his own cost).

Labour for boring hole for inserting tube well pipes through different soil/ rock media including hire charges of drill pipes, scaffolding, tools and plants as necessary and taking out the same and lowering pipes, fittings complete as directed by the Department.Bore hole of 150mm diameter

Supplying, fitting and fixing pipes plain/bevel ended for casing, conforming to relevant IS codes of practice including supplying and fitting of tube well accessories, lowering of assembly pipes concentrically in the borehole followed by supplying and packing of pea gravel free from dirt, dust and other foreign materials in the annular space between the borehole and assembly pipes complete as directed by the Department.PVC PIPE (v) 110mm diameter

Supplying fitting and fixing ISI approved PVC filter 3.00 metre long.

Supplying, fitting and fixing suction pipes plain/bevel ended, conforming to relevant IS codes of practice including supplying and fitting of accessories, lowering of assembly pipes concentrically in the casing pipes complete as directed.PVC PIPE iv) 50mm

Supplying fitting and fixing check valve (non return valve) including thread to pipes.

Development of the tube well with compressor or by over pumping unit for 48 hours till sand free discharge is obtained

Supplying and placing plastic cylindrical vertical claused top (PCVC) tank of Sintex / Polycon / Patton make over the stagging with manhole cover with locking and cleaning arrangement including providing pads of size as required for inlet and outlet pipes 2000 Lt capacity (a) Sintex make

Labour for erecting and placing PCVC Tank over the stagging up to a height of 5.00m complete as directed.2000 Lt capacity(a) Sintex make

Supplying fitting and fixing Pipes with all necessary fittings in exposed or in trenches including trenching and refilling the same etc complete as directed C) CPVC pipe with CPVC fittings (Using SUPREME/ PRINCE/ SFMC/ FUSION brand pipe)v) 40 mm (OD) diameter

Supplying fitting and fixing Pipes with all necessary fittings in exposed or in trenches including trenching and refilling the same etc complete as directed C) CPVC pipe with CPVC fittings(Using SUPREME/ PRINCE/ SFMC/ FUSION brand pipe)v)iv) 32 mm diameter

Supplying fitting and fixing Pipes with all necessary fittings in exposed or in trenches including trenching and refilling the same etc complete as directed C) CPVC pipe with CPVC fittings(Using SUPREME/ PRINCE/ SFMC/ FUSION brand pipeiii) 25mm (OD) diameter

Supplying fitting and fixing Pipes with all necessary fittings in exposed or in trenches including trenching and refilling the same etc complete as directed C) CPVC pipe with CPVC fittings(Using SUPREME/ PRINCE/ SFMC/ FUSION brand pipeii)20mm (OD) diameter

Supplying fitting and fixing C.P. bib cock 15mm dia of approved brand directed and specified. (G.I. & C.P pipes will be measured separately)

Supplying fitting and fixing chrome plated (C.P.) stop-cock of approved brand and size as mentioned below as directed and specified.(G.I. & C.P pipes will be measured and paid separately) Jaquar (a) Continental / Clarion (a) 15mm dia

Supplying and fitting gun metal country pit valve (full way valve) I.S.I. Make as specified and directed.(a) 50mm dia

Providing fitting and fixing Mirror with plastic frame of size 500x400mm complete as directed and specified.

Providing, fitting and fixing recessed soap tray / soap dish complete as directed and specified.

Providing, fitting and fixing CP towel rail complete as directed and specified.

Supplying and fitting fixing C.P. pillar cock of 15mm dia of approved brand as specified and directed. Jaguar make (a) Continental

Supplying fitting and fixing Chrome Plated (C.P.) sink cock of approved brand as directed and specified. (G.I. & C.P pipes will be measured and paid separately) Jaquar branda) Continental / Clarion

Supplying fitting and fixing overhead adjustable Chrome Plated (C.P.) spray shower 15mm dia. of Sona make with wall flange as directed and specified.(pipes will be measured and paid separately)(a) Supreme shower with arm

Supplying including installation of submersible taype water supply motor pumset with all accessories etc all complete as directed. 1 H.P. Single Phase

Wiring for light/Fan/call bell point with 2x1.5 Sq. mm P.V.C. insulated single core unsheathed industrial (Multistrand) cable HFFR/ZHFR conforming to 1S-694. 1990 with flexible bright annealed electrolytic copper conductor voltage grade up to 1100 volts in surface Bat 19 nun ISI marked casing ‘N’ capping (AKG Precision, Presto /Plast/polycab/MW or equivalent make as approved by the Deptt. GI/MS switch board (ISI) marked) half conceal on wall with phenolic laminated sheet cover ceiling rose (Anchor pent' ) Gold medal Calor kany Kom /havells or equivalent make as approved by the Deptt. Etc. complete. (i) Shot point upto 3,00 m length

Wiring for light/Fan/call bell point with 2x1.5 Sq. mm P.V.C. insulated single core unsheathed industrial (Multistrand) cable HFFR/ZHFR conforming to 1S-694. 1990 with flexible bright annealed electrolytic copper conductor voltage grade up to 1100 volts in surface Bat 19 nun ISI marked casing ‘N’ capping (AKG Precision, Presto /Plast/polycab/MW or equivalent make as approved by the Deptt. GI/MS switch board (ISI) marked) half conceal on wall with phenolic laminated sheet cover ceiling rose (Anchor pent' ) Gold medal Calor kany Kom /havells or equivalent make as approved by the Deptt. Etc. complete. (ii) Medium point upto 6,00 m length

Wiring for light/Fan/call bell point with 2x1.5 Sq. mm P.V.C. insulated single core unsheathed industrial (Multistrand) cable HFFR/ZHFR conforming to 1S-694. 1990 with flexible bright annealed electrolytic copper conductor voltage grade up to 1100 volts in surface Bat 19 nun ISI marked casing ‘N’ capping (AKG Precision, Presto /Plast/polycab/MW or equivalent make as approved by the Deptt. GI/MS switch board (ISI) marked) half conceal on wall with phenolic laminated sheet cover ceiling rose (Anchor pent' ) Gold medal Calor kany Kom /havells or equivalent make as approved by the Deptt. Etc. complete. (iii) Long point upto 10,00 m length

Wiring for 5/6 pin Amps power plug point with 4 sq. mm P.V.C. insulated single core unsheathed industrial cable HFFR/ZHFR conforming to IS-694: 1990 with flexible bright annealed electrolytic cooper conductor for voltage grade up to 1100 volts in surface flat 19 mm ISI marked casing ‘n’ capping including providing and fixing 5/6 pin 16 Amps flush type socket outlets and 160Amps flush type switch with phenolic laminated sheet cover earth continuity with 2.5 sq. mm. cable to the 3rd pin of the socket as required complete. (i) Medium point upto 6,00 m length

Wiring for light/fan/call bell point 3x1.5 sq. mm. P.V.C. insulated single core unsheathed industrial in surface flat 19 mm ISI marked casing ‘n’ caping including 6 Amp flush type switch/bell push with phenolic laminated sheet cover, ceiling rose etc. complete. (i) Long point upto 10,00 m length

Wiring circuit wiring with 2x1.5 sq. mm P.V.C. insulated single core unsheathed industrial cable HFFR/ZHFR conforming to IS-694, 1990 with flexible bright annealed electrolytic cooper conductor for voltage grade up to 1100 volts in surface flt 19 mm ISi marked casing ‘n’ capping system , including connection as required. (i) with 2x1.5 sq. mm 019 mm dia ISI mark Conduit

Wiring for drawing sub-main line with P.V.C. insulated single core unsheathed industrial cable HFFR/ZHFR conforming to IS-694: 1990 with flexible bright annealed electrolytic cooper conductor for voltage grade up to 1100 volts in surface flat ISI marked casing ‘n’ capping including earth continuity. a) with 4x4 sq. mm + earth continuity with 2x1.5 sq. mm cable in surface flat 15 mm casing system a) with 3 x 6 sq. mm + earth continuity with 2x2.5 sq. mm cable in surface flat 25 mm ISI marked casing 'n' capping system

Wiring for drawing sub-main line with P.V.C. insulated single core unsheathed industrial cable HFFR/ZHFR conforming to IS-694: 1990 with flexible bright annealed electrolytic cooper conductor for voltage grade up to 1100 volts in surface flat ISI marked casing ‘n’ capping including earth continuity. a) with 3 x6 sq. mm + earth continuity with 2x2.5 sq. mm cable in surface flat 15 mm casing system a) with 4 x 4 sq. mm + earth continuity with 2x1.5 sq. mm cable in surface flat 15 mm ISI marked casing 'n' capping system

Providing and fixing I.C.S.P. and N Link main Switch of 240 volt grade including drilling boards/iron frames and fixing with bolts and nuts and connection as approved by the Deptt.) complete as required. (I 60/63 Amps capacity T.P.N.

Providing and fixing I.C. distribution fuse boards with rewire able fuses 250 volt grade, 16 Amps per way including drilling boards/iron frames and fixing with bolts and nuts and connection as approved by the Deptt.) complete as required 6-way Capacity

Supplying including fitting and fixing steel, phosphatised, powder painted single door surface mounting MCB DB incorporated with bas-bar neutral link, earth bar and din rail etc. fitted on wall with grouting nuts & bolts as reqd. complete with making necessary connection as approved, specified and directed by the deptt. (i) 4 way SPN single door

Supplying including fitting and fixing of the following A.C. ceiling fan complete with all accessories like down rod, canopy etc. of following sweeps with making necessary connection as approved by the deptt. As required complete and as directed by the department. (i) Standared model 1400 mm sweep ( Orient PSPO make / Usha make / Cromton make / Hevellas / ATc / V Guard make)

Supplying installation & testing of G.I. earth stations with perorated 40 mm dia and 4.50 m long G.I. pipe with necessary 40mm dia G.I. fittings such as socket. Tee, elbow, nipple and 50mm x 40mm G.I reducer socket for funnel including locking arrangement 300,, x 300mm x 6mm hinges cover C.I earth plate complete with digging of earth pit, construction of brick chamber and plastering of both inner & outer surface of wall as directed and as specified by the deppt. surface at wall as specified & directed by department. with surface at wall as specified direction by department

Supplying and drawing of whether proof aluminum conductor cable of the following size as directed and specified by the department. (i) 6.00 sq. mm twin core D.B.S.W.g wire per kg

5-10 Amp. ISI approved single metre (single) market price

ASEB Lade connection

Supplying and drawing of whether proof aluminum conductor cable of the following size as directed and specified by the department. (i) 6.00 sq. mm twin core with 4 x 6 sq.mm

Supplying and erection Psc pole 7.5 metre long, the pole is to be erection in 1.2.3. plain cement concreate foundation of size 1.50 m x 0.45 m x0.45 m having P.C.C base foundation 15 cm x60cm portion 0.30 metre complete with excavation of earth handling of surplus soil, debris etc. to the proper place and refilling etc. as specified and as directed by the depertment.

Batko light T.M.s 540 1 x TL 554 who with 1 x 154 w T-5

With 3 x 10 sq. mm. + earth continuity with2x 6 sq. mm. cable in 25 mm. dia. ISI marked hot dip galvanised pipe s.

M/S SUNRISE ENTERPRISE