PROVIDING IMPROVEMENT ACCESS TO WATER THROUGH HOUSE HOLD CONNECTIONS IN EXISTING WATER SUPPLY SCHEME BIROKE KALAN, BLOCK BUDHLADA, DISTT. MANSA

Item Wise Description :

Carriage of Surkhi, sand, bajri, ballast, stone, boulders, kankar, building rubbish Carriage of material excluding initial lead of 5 Km (a) Jalalabad Sand (Av. Lead 167 Km) Up to 40 km CSR Item No. 5.2 (i)

41 km to 60 km

61 km to 150 km

150 km to 167 km

(b) Gagger Sand (Av Lead 320 Km.) from Pathankot Up to 40 km CSR Item No. 5.2 (i)

41 km to 60 km

61 km to 150 km

150 km to 320 km

(d) Bajri (Av Lead 320 Km.) Up to 40 km CSR Item No. 5.2 (i)

41 km to 60 km

61 km to 150 km

150 km to 320 km

(b) Filter Media (Av. Lead 320 Km) Up to 40 km CSR Item No. 5.2 (i)

41 km to 60 km

61 km to 150 km

150 km to 167 km

Carriage of sand for earth filling a lead of 5 Kms CSR Item No. 5.2

Earth work in excavation in foundations, trenches etc.in all kinds of soil where pick jumper work is not involved and not exceeding 2.0 metres depth including dressing of bottom and sides of trenches, stacking the excavated soil clear from the edge of excavation CSR Item No. 6.6

Earth filling under floors with surplus ordinary soil or soil containing gravel or kankar upto 40% excavated from foundation and taken only from outside the building plinth in 15 cm layers including ramming, watering and consolidating lead upto 30 metres CSR Item No. 6.8 a) i

Cement concrete 1:8:16 with Stone ballast 40mm gauge using concrere mixer volumatric type CSR Item No. 10.6 (b) ii

Cement Concrete 1:2:4 with stone ballast or shingle using concrete mixer volumetric type. CSR Item No. 10.12 (ii)

DPC 25mm thick of cement concrete 1:2:4 with two coats of bitumen 20/30 at 1.65 Kg/sqm. Laid in hot and sanded. CSR Item No. 10.30

First class burnt brick work laid in cement sand mortar 1:5 in foundation and plinth CSR Item No. 11.5

First class burnt brick work laid in cement sand mortar 1:5 in first storey upto 4 metres above plinth level. CSR Item No. 11.6

115 mm thick brick wall laid in cement mortar 1:4 without reinforcement in foundation and plinth. CSR Item No. 11.35

Conglomerate floor 50mm thick cement concrete topping 1:2:4. CSR Item No. 14.7

12.5mm thick cement plaster 1:2 CSR Item No. 15.7

12.5mm thick cement plaster 1:4 CSR Item No. 15.9

12.5mm thick cement plaster 1:5 CSR Item No. 15.10

Cement pointing 1:2 deep variety. CSR Item No. 15.59

White washing (Three coats) CSR Item No. 16.3

Finishing walls with exterior decortive cement based point such as snowcem. CSR Item No. 16.14

Applying pink primer on aluminum priming coat on wood work including prepration of surface knotting and stopping. a) With Special Quality paint. CSR Item No. 16.17

Painting two coats excluding priming coat with synthetic enamel paint in all shades on wood work, metallic or plastered, concrete surface to give an even shade. a) With special quality paint. CSR Item No. 16.18

Applying priming coat with metal primer on new steel or iron work including preparation of surface. CSR Item No. 16.21 (b)

Painting two coats including priming coat with ready mixed paint for metallic surface in all shades on new steel or iron work. CSR Item No. 16.22 (b)

Hollock wood, doors, shutter, windows, shutter including hinges, screws, chocks, cheats, stops, cords etc. complete fixed in position. (ii) 35 mm thick CSR Item No. 17.10 (iii)

Steel work fixed independently without connecting plates including hoisting & fixing in position oa angle & channel. CSR Item No. 18.1

Wrought iron and mild steel ladders, framed grills, grating etc. with ends of bars, riveted or welded or forged, framed window guards, barred iron doors, stair case, iron railing including cost of bolts and nuts or screws or welding rod, complete fixed in position. CSR Item No. 18.4

Providing, Laying, fixing & jointing of P.V.C Pipes as per ISI-4985 (ISI Marked with the prior approval of Engineer-in-Charge) along the Trenches and laying the same in Trenches to correct alignment and gradlents, cutting, jointing and testing complete as per specifications .Including specials and excavation minimum cover 1 mtr (6kg/cm2 pressure) 63 mm o/d CSR Item No. 28.13 b) + 28.18 + 28.2

Providing & fixing C.I/D.I Flanged end, stem of SS (AIS 1410 ) and Bronze ( gunmeted) working parts Sluice Valves ISI marked 14846-2000, including, jointing, testing & cost of Nut, Bolt & insertion sheet all carriage complete ( with the approval of Engineer-in-Charge). CSR Item No. 28.27 A (a) 80mm i/d Sluice Valves

100mm i/d Sluice Valves

150mm i/d Sluice Valves

200mm i/d Sluice Valves

Bailing out water from the trenches for making new connections in fully charged pipe lines including cleaning trimming and dressing the trenches to correct alignment and grade as required CSR Item No. 28.49 A (a) Upto 300mm i/d

Providing and placing in horizontal layers filtering mei/d screened, washed and cleaned as described below (a) Top layer :----- Fine sand screened, cleaned and washed and graded (effective size 0.2 to 0.4mm with uniformity coefficient 2.00 to 3.00) from Pathankot or other approved source. CSR Item No. 28.51

Construction of masonary sluice Valve Chamber excluding Sluice valve cover as per standard design & drawings of public health department. (a) 0.60 mtr x 0.60 mtr. CSR Item No. 28.66

Hand boring Horizontly for crossing of pipe under road or any other obstacle by using Auger/Bocki method . Including excavation, stringing and jointing of pipe upto 160mm complete CSR Item No. 28.71

Providing & fixing 560mm, 500mm and 450mm internal Diametre circular or 455 mm x 610mm clear inside opening rectangular cast iron manhole cover and frame ISI marked as per IS12592-2002 including carriage from the stores of the Engineer-in-charge to site of work, loading, unloading including stacking and setting the same to correct lines and levels in 1:2 cement sand mortar over manholes including cement concrete copping (1:2:4)around the frame etc.Dia of steel for lifting hook is 16mm. CSR Item No. 29.36

Non Schedule Items Taking out and washing filter media and placing the same after washing, cleaning in filter beds (A) Top Layer :-- Fine sand screened, cleaned and washed and graded (effective size 0.2 to 0.4mm with uniformity coefficient 2.00 to 3.00)

(B) Second Layer :-- Coarse sand screened, cleaned and washed and graded from 3mm to 6mm

(C) Third Layer :-- Bajri screened, cleaned and washed and graded from 6mm to 20mm

(D) Fourth Layer :--- Bajri (Coarse) screened, cleaned and washed and graded from 20mm to 25mm

(F) Bottom Layer :-- Broken stone, screened, cleaned and washed and graded from 50mm to 75mm

Non Schedule Item Labour for making 3 No. holes & 1 No. cut in case of angle iron pickets.

Non Schedule Item Providing & fixing barbed wire fencing 3 ply rating with angle iron pickets with M.S. clips including labour for stretching of barbed wire & cost of clips.

Non Schedule Item Providing and fixing MS Hooks.

Non Schedule Item Providing & fixing of 250 mm i/d expansion Joint

Non Schedule Item Dismantling brick of flanged stone flooring without concrete base and recondition

Non Schedule Item Providing, installing, testing & Commissioning one no. Electronically acturated, Diaphragm operated, Metering system, Chemical Dosing Chlorinator, suitable for delivering 0.5 to 6.0 Litres of Bleaching powder solution/ Sodium Hypo Solution per Hour under maximum delivery pressure up to 7 kg./ sqcm and suction lift not less than 1.5m as per DWSS standard specifications.

Non Schedule Item Providing house hold connection including laying, jointing, fixing testing below ground level MDPE pipe and above of ground level GI pipes (as approved by Engineer-In-Charge), including cost of excavation, Refilling, CI bib cock as per IS:210 with stainless steel spindle, 15mm i/d GI pipe 2.50 Mtr. & 15mm i/d MDPE pipe 2.00 Mtr. (length on average basis) 3" uPVC clamp, ISI marked G.M. Ferrule as per IS:2692 connection of 15mm i/d ferrule midium, specials such as tees, bends, sockets, elbow, nipples (100 mm & 150mm) Union Copplings, GI hooks etc., cutting, threading, making hole in wall and testing in treanches in the ground all material should be of approved make (to the approval of Engineer-in-charge) complete in all respect including cost of carriage. (Ref. CSR item Nos. 28.1, 28.36, 28.34 B, 30.65 b. Water Connection on Old pipe line

Water Connection on New pipe line

Repair of old water connection

Non Schedule Item Painting of Sign Board

Credit of old panel board for Raw water motor of capacity 5 BHP (N.S. Rates) (-)

Credit of old panel board for Raw water motor of capacity 20 BHP (N.S. Rates) (-)