Repair / maintenance, replacement of water pipe line and other connected items for day to day complaints at Suratgarh Mil Stn

Amount

M&L for opening of centrifugal pump capacity 150 / 125 HP by disconnecting from motor and pipe, strip opening the pump and replacement of unserviceable parts such as impeller, bushes, shaft sleeves, ball bearing, nut bolts, gland plate, gasket, water hose pipe etc and lathe work/turning, grinding etc on shaft and shaft key way as required including greasing/oiling and re-assembling at the same location with proper alignment with motor and testing complete all as specified and directed by Engineer-in-charge. Note : - (i) Major items like impeller, bearing, bush, gland plate, tyre coupling, coupling assembly shall be measured and paid for separately under respective items of BOQ as “Supply only”. (ii) Cost for transportaion to workshop and carry back to site after repair is inlcuded in the unit rate of item nothing extra shall be paid on this acount.

All as per serial item No 1 here-in-above but centrifugal pump capacity 100 / 75 HP

All as per serial item No 1 here-in-above but centrifugal pump capacity 60 / 50 HP

All as per serial item No 1 here-in-above but centrifugal pump capacity 40 / 30 HP

All as per serial item No 1 here-in-above but centrifugal pump capacity 25 / 20 HP

All as per serial item No 1 here-in-above but centrifugal pump capacity 15 / 12.5 HP

All as per serial item No 1 here-in-above but centrifugal pump capacity 10 / 7.5 / 5 HP

All as per serial item No 1 here-in-above but centrifugal pump capacity 5 / 3 HP

All as per serial item No 1 here-in-above but centrifugal pump capacity 2 / 1 HP

All as per serial item No 1 here-in-above but multistage chlorine pump capacity 3 / 2 HP

Supply only CI impeller suitable for centrifugal Pump set capacity 150 / 125 HP motor complete all as specified and directed by Engineer-in-charge.

All as per serial item No 11 here-in-above but centrifugal pump capacity 100 / 75 HP

All as per serial item No 11 here-in-above but centrifugal pump capacity 60 / 50 HP

All as per serial item No 11 here-in-above but centrifugal pump capacity 40 / 30 HP

All as per serial item No 11 here-in-above but centrifugal pump capacity 25 / 20 HP

All as per serial item No 11 here-in-above but centrifugal pump capacity 15 / 12.5 HP

All as per serial item No 11 here-in-above but centrifugal pump capacity 10 / 7.5 / 5 HP

All as per serial item No 11 here-in-above but centrifugal pump capacity 5 / 3 HP

All as per serial item No 11 here-in-above but centrifugal pump capacity 2 / 1 HP

All as per serial item No 11 here-in-above but multistage chlorine pump capacity 3 / 2 HP

Supply only Stainless steel Bush suitable for centrifugal Pump capacity 150 / 125 HP motor complete all as specified and directed by Engineer-in-charge.

All as per serial item No 21 here-in-above but centrifugal pump capacity 100 / 75 HP

All as per serial item No 21 here-in-above but centrifugal pump capacity 60 / 50 HP

All as per serial item No 21 here-in-above but centrifugal pump capacity 40 / 30 HP

All as per serial item No 21 here-in-above but centrifugal pump capacity 25 / 20 HP

All as per serial item No 21 here-in-above but centrifugal pump capacity 15 / 12.5 HP

All as per serial item No 21 here-in-above but centrifugal pump capacity 10 / 7.5 / 5 HP

All as per serial item No 21 here-in-above but centrifugal pump capacity 5 / 3 HP

All as per serial item No 21 here-in-above but centrifugal pump capacity 2 / 1 HP

All as per serial item No 21 here-in-above but multistage chlorine pump capacity 3 / 2 HP

Supply only Gland plate suitable for centrifugal Pump capacity 150 / 125 HP motor complete all as specified and directed by Engineer-in-charge.

All as per serial item No 31 here-in-above but centrifugal pump capacity 100 / 75 HP

All as per serial item No 31 here-in-above but centrifugal pump capacity 60 / 50 HP

All as per serial item No 31 here-in-above but centrifugal pump capacity 40 / 30 HP

All as per serial item No 31 here-in-above but centrifugal pump capacity 25 / 20 HP

All as per serial item No 31 here-in-above but centrifugal pump capacity 15 / 12.5 HP

All as per serial item No 31 here-in-above but centrifugal pump capacity 10 / 7.5 / 5 HP

All as per serial item No 31 here-in-above but centrifugal pump capacity 5 / 3 HP

All as per serial item No 31 here-in-above but centrifugal pump capacity 2 / 1 HP

S&F in replacement Rubber tyre for coupling suitable for centrifugal Pump set capacity 150 / 125 HP motor including replacement of unserviceable nut, bolt and washer complete all as specified and directed by Engineer-in-charge. Make : Unique, Fenner

All as per serial item No 40 here-in-above but centrifugal pump capacity 100 / 75 HP

All as per serial item No 40 here-in-above but centrifugal pump capacity 60 / 50 HP

All as per serial item No 40 here-in-above but centrifugal pump capacity 40 / 30 HP

All as per serial item No 40 here-in-above but centrifugal pump capacity 25 / 20 HP

All as per serial item No 40 here-in-above but centrifugal pump capacity 15 / 12.5 HP

All as per serial item No 40 here-in-above but centrifugal pump capacity 10 / 7.5 / 5 / 3 HP

S&F in replacement Coupling assembly suitable for centrifugal Pump set capacity 150/125 HP motor complete all as specified and directed by Engineer-in-charge. Make : Unique, Fenner

All as per serial item No 47 here-in-above but centrifugal pump capacity 100 / 75 HP

All as per serial item No 47 here-in-above but centrifugal pump capacity 60 / 50 HP

All as per serial item No 47 here-in-above but centrifugal pump capacity 40 / 30 HP

All as per serial item No 47 here-in-above but centrifugal pump capacity 25 / 20 HP

All as per serial item No 47 here-in-above but centrifugal pump capacity 15 / 12.5 HP

All as per serial item No 47 here-in-above but centrifugal pump capacity 10 / 7.5 / 5 HP

All as per serial item No 47 here-in-above but centrifugal pump capacity 3 / 2 HP

S&F in replacement Ball bearing suitable for centrifugal Pump / motor capacity 150 / 125 HP with proper T&P / bearing puller and lathe work on shaft of pump / motor as required and testing complete all as specified and directed by Engineer-in-charge. Make : NBC, SKF, TATA

All as per serial item No 55 here-in-above but centrifugal pump capacity 100 / 75 HP

All as per serial item No 55 here-in-above but centrifugal pump capacity 60 / 50 HP

All as per serial item No 55 here-in-above but centrifugal pump capacity 40 / 30 HP

All as per serial item No 55 here-in-above but centrifugal pump capacity 25 / 20 HP

All as per serial item No 55 here-in-above but centrifugal pump capacity 15 / 12.5 HP

All as per serial item No 55 here-in-above but centrifugal pump capacity 10 / 7.5 HP

All as per serial item No 55 here-in-above but centrifugal pump capacity 5 / 3 HP

All as per serial item No 55 here-in-above but centrifugal pump capacity 2 / 1 HP

M&L for rewinding the three phase electric motor of 150 / 125 HP, 415 volts, AC with super enamelled copper winding wire of existing gauge including varnishing, baking, cotton tape and making proper electrical connection complete all as specified and directed by Engineer-in-charge. Make of winding wire : Devidayal, Chetak Note : Transportation of motor to contractor's workshop is included in the unit rate of items and nothing extra shall be paid on this account.

All as per serial item No 64 here-in-above but electric motor capacity 100 / 75 HP

All as per serial item No 64 here-in-above but electric motor capacity 60 / 50 HP

All as per serial item No 64 here-in-above but electric motor capacity 40 / 30 HP

All as per serial item No 64 here-in-above but electric motor capacity 25 / 20 HP

All as per serial item No 64 here-in-above but electric motor capacity 15 / 12.5 HP

All as per serial item No 64 here-in-above but electric motor capacity 10 / 7.5 HP

All as per serial item No 64 here-in-above but electric motor capacity 5 / 3 HP

All as per serial item No 64 here-in-above but electric motor capacity 2 / 1 HP

Taking down old unserviceable metal body cooling fan and S&F cooling fan suitable for electric motor of capacity 150/125/100 HP motor including replacement of lock and key, nut etc complete all as specified and directed by Engineer-in-charge.

All as per serial item No 73 here-in-above but cooling fan for electric motor of 75/60/50 HP

All as per serial item No 73 here-in-above but PVC body cooling fan for electric motor of 40/30 HP

All as per serial item No 73 here-in-above but PVC body cooling fan for electric motor of 25/20 HP

All as per serial item No 73 here-in-above but PVC body cooling fan for electric motor of 15/12.5/10 HP

All as per serial item No 73 here-in-above but PVC body cooling fan for electric motor of 7.5/5 HP

All as per serial item No 73 here-in-above but PVC body cooling fan for electric motor of 3/2/1.5/1 HP

Supply & Fixing replacement of terminal bakelite connection plate with nut, bolts etc suitable for 3 phasse, 415 volts, AC, star/delta connection, electric motor of capacity 150/125/100 HP including replacement of copper thimble, brass nut, bolt, washer complete all as specified and directed by Engineer-in-charge.

All as per serial item No 80 here-in-above but for electric motor of 75/60 HP

All as per serial item No 80 here-in-above but for electric motor of 50/40 HP

All as per serial item No 80 here-in-above but for electric motor of 30/25 HP

All as per serial item No 80 here-in-above but for electric motor of 20 HP

All as per serial item No 80 here-in-above but for electric motor of 15/12.5/10 HP

All as per serial item No 80 here-in-above but for electric motor of 7.5/5 HP

All as per serial item No 80 here-in-above but for electric motor of 3/2/1.5/1 HP

M&L for repair to sludge pump of capacity 10 / 15 HP by taking out the pump from sludge well carefully with chain pully block or other T&P as required on site and strip opening the pump for repair and replacement of unserviceable parts such as impeller, gun metal bushes, stainless steel sleeves, impeller key, water seal, nut bolts, washer, lugs etc and re-assembling at the same and lowering in the well in its original position with electrical wiring and testing complete all as specified and directed by Engineer-in-charge.

M&L for taking out defictive submersible pump set of capacity upto 15 HP Capacity from bore well after disconnecting electrical connections, transportation to workshop for repair, dismantling the pump set for detection of repair such as rewinding of motor, replacement of iron stainer, bronze impeller, gun metal bushes stainless steel sleeve, impeller key, thrust bearing, replacement of unserviceable nut-bolts, washer, lugs, terminal plate, reassembling, lowering of pump & strainer in well in its original position, making proper electrical connections, commissioning & testing complete all as specified and directed by Engineer-in-charge. Note : - (i) Cost for transportaion to workshop carry back to site after repair is inlcuded in the unit rate of item quoted by contractor and nothing extra shall be paid on this acount. (ii) Rewinding of submersible motor, Iron stainer, bronze impeller, gun metal bushes stainless steel sleeve, impeller key and thrust bearing if required for replacement shall be paid separetly against respective items of BOQ as "Supply only". (iii) Lathe work and grinding of shaft if required shall be paid separately against respective items of BOQ. (iv) Cost of new nuts, bolts, washers, lugs and terminal plate required to be replaced is included in the unit rate of item quoted by the contractor and nothing extra shall be paid on this account.

(a) Iron stainer for pump 7.5/10 HP

(b) Bronze impeller with key for pump 7.5/10 HP

(c) Gun metal Bush for pump 7.5/10 HP

(d) Stainless steel sleeves for pump 7.5/10 HP

(e) Thrust bearing of Gun metal for pump 7.5/10 HP

(f) Water seal for pump 7.5/10 HP

(a) Iron stainer for pump 12.5/15 HP

(b) Bronze impeller with key for pump 12.5/15 HP

(c) Gun metal Bush for pump 12.5/15 HP

(d) Stainless steel sleeves for pump 12.5/15 HP

(e) Thrust bearing of Gun metal for pump 12.5/15 HP

(f) Water seal for pump 12.5/15 HP

Supply only PVC rope / toching rope minimum 2.5cm dia for submersible pump complete all as specified and as directed by Engineer –in-charge.

M&L for rewinding of motor of submersible pump set of capacity 7.5 / 10 HP with super enamelled copper winding wire of existing gauge including varnishing, baking, cotton tape and greasing of bearings, bushes and other connected parts and making necessary hook/clamp arrangement or body for attachning PVC rope complete all as specified and directed by Engineer-in-charge. Make of winding wire : Devidayal, Chetak

All as per serial item No 103 here-in-above but for motor of submersible pump set of capacity 12.5 / 15 HP

S&F in replacement of GI coloumn pipe for submersible pump, 80mm dia bore 'heavy grade' ISI marked both end flanged and 3 mtr length piece with nut bolts and gasket etc complete all as specified and as directed by Engineer –in-charge.

S&F in replacement of UPVC coloumn pipe, heavy duty, ISI marked for submersible pump, 80mm dia, socket/outer thread end of 3 mtr length complete all as specified and as directed by Engineer –in-charge.

S&F in replacement of UPVC coloumn pipe, heavy duty, ISI marked for submersible pump, 100mm dia, socket/outer thread end of 3 mtr length complete all as specified and as directed by Engineer –in-charge.

M&L for rewiring of star-delta starter of motor capacity upto 150 / 125 / 100 HP by taking down of all parts and rewiring of complete starter with control wiring with multistranded copper wire and replacement of unserviceable copper thimbles, nut bolts, pvc connectors, links, insulator etc complete all as specified and as directed by Engineer –in-charge. Note: - New Nuts, bolts, washers, copper thimbles, connectors and insulators if required for refixing shall be provided by the contractor & the cost of item is deemed to be included in the unit rate quoted by the contractor and nothing extra shall be paid on this account.

All as per serial item No 108 here-in-above but for starter for motor of capacity of 75/60/50 HP

All as per serial item No 108 here-in-above but for starter for motor of capacity of 40/30/25 HP

All as per serial item No 108 here-in-above but for starter for motor of capacity of 20/15 / 10 HP

Supplying, laying, jointing & testing in replacement submersible cable, 1100 volts, IS:694, flat type, copper conductor of size 16 Sqmm, 3 core complete all as specified & as directed by Engineer –in-charge.

All as per serial item No. 112 here-in-above but 6 Sqmm 3 core.

All as per serial item No. 112 here-in-above but 4 Sqmm 3 core.

Supplying, laying & jointing in replacement of PVC insulated single core, copper conductor cable, 1100 volts, IS : 694, unsheathed, heat resistant and flame retardent of size 70 Sqmm complete all as specified & as directed by Engineer –in-charge.

All as per serial item No. 115 here-in-above but 50 Sqmm.

S&F in replacement MCCB 3 Pole 400 Amps, thermal magnetic release having, breaking capacity 50 KA, 415 Volt complete all as specified and as directed by Engineer-in-Charge. Make : Legrand Cat Part No. DPX³ 630 422016 or equivalent in L&T / Schneider / ABB

S&F in replacement MCCB 3 Pole 250 Amps, thermal magnetic release having, breaking capacity 50 KA, 415 Volt complete all as specified and as directed by Engineer-in-Charge. Make : Legrand Cat Part No. DPX³ 250 420269 or equivalent in L&T / Schneider / ABB

S&F in replacement MCCB 3 Pole 160 Amps, thermal magnetic release having, breaking capacity 50 KA, 415 Volt complete all as specified and as directed by Engineer-in-Charge. Make : Legrand Cat Part No. DPX³ 160 420127 or equivalent in L&T / Schneider / ABB

S&F in replacement MCCB 3 Pole 100 Amps, thermal magnetic release having, breaking capacity 50 KA, 415 Volt complete all as specified and as directed by Engineer-in-Charge. Make : Legrand Cat Part No. DPX³ 160 420125 or equivalent in L&T / Schneider / ABB

S&F in replacement of power contactor, AC3 rating, 200 Amps, 3 Pole, AC control with Auxiliary contacts 2 NO + 2NC, suitable for coil voltage 110 V, 220, 240 & 415 volts, 50 Hz complete all as specified and as directed by Engineer-in-Charge. Make: Schneider/ L&T/ Siemens

S&F in replacement of power contactor, AC3 rating, 160 Amps, 3 Pole, AC control with Auxiliary contacts 2 NO + 2NC, suitable for coil voltage 110 V, 220, 240 & 415 volts, 50 Hz complete all as specified and as directed by Engineer-in-Charge. Make: Schneider/ L&T/ Siemens

S&F in replacement of power contactor, AC3 rating, 120 Amps, 3 Pole, AC control with Auxiliary contacts 2 NO + 2NC, suitable for coil voltage 110 V, 220, 240 & 415 volts, 50 Hz complete all as specified and as directed by Engineer-in-Charge. Make: Schneider/ L&T/ Siemens

S&F in replacement of power contactor, AC3 rating, 95 Amps, 3 Pole, AC control with Auxiliary contacts 2 NO + 2NC, suitable for coil voltage 110 V, 220, 240 & 415 volts, 50 Hz complete all as specified and as directed by Engineer-in-Charge. Make: Schneider/ L&T/ Siemens

S&F in replacement of power contactor, AC3 rating, 80 Amps, 3 Pole, AC control with Auxiliary contacts 2 NO + 2NC, suitable for coil voltage 110 V, 220, 240 & 415 volts, 50 Hz complete all as specified and as directed by Engineer-in-Charge. Make: Schneider/ L&T/ Siemens

S&F in replacement of power contactor, AC3 rating, 65 Amps, 3 Pole, AC control with Auxiliary contacts 2 NO + 2NC, suitable for coil voltage 110 V, 220, 240 & 415 volts, 50 Hz complete all as specified and as directed by Engineer-in-Charge. Make: Schneider/ L&T/ Siemens

S&F in replacement of power contactor, AC3 rating, 50 Amps, 3 Pole, AC control with Auxiliary contacts 2 NO + 2NC, suitable for coil voltage 110 V, 220, 240 & 415 volts, 50 Hz complete all as specified and as directed by Engineer-in-Charge. Make: Schneider/ L&T/ Siemens

S&F in replacement of power contactor, AC3 rating, 32 Amps, 3 Pole, AC control with Auxiliary contacts 2 NO + 2NC, suitable for coil voltage 110 V, 220, 240 & 415 volts, 50 Hz complete all as specified and as directed by Engineer-in-Charge. Make: Schneider/ L&T/ Siemens

S&F in replacement of power contactor, AC3 rating, 18 Amps, 3 Pole, AC control with Auxiliary contacts 2 NO + 2NC, suitable for coil voltage 110 V, 220, 240 & 415 volts, 50 Hz complete all as specified and as directed by Engineer-in-Charge. Make: Schneider/ L&T/ Siemens

S&F in replacement of thermal over load relay adjustment range 124-198 / 84-135 / 62-99 amps with relay mounting block, all electrical control wiring complete all as specified & as directed by Engineer-in-charge.

All as per item No 130 here-in-above but relay adjustment range 48-65 Amps

All as per item No 130 here-in-above but relay adjustment range 16-24/ 23-32 / 30-40 / 37-50 Amps

All as per item No 130 here-in-above but relay adjustment range 12-18 Amps

S&F in replacement of motor protection relay with digital display, 96x96mm panel mounted, auto reset, protection for phase, voltage, current, frequency, 415 volt AC three phase with fault indicator and auto reset with all control wiring and CT/PT and testing complete all as specified & as directed by Engineer-in-charge.

S&F in replacement of electronic timer 0 to 30 second for star - delta changeover, DIN mounting complete all as specified & as directed by Engineer-in-charge.

S&F in replacement of 3 phase preventor (SPP) with auto reset, 415 Volts AC complete all as specified & as directed by Engineer-in-charge.

S&F in replacement of digital voltmeter (50-550V), 3 phase, 96x96 mm with CT complete all as specified & as directed by Engineer-in-charge.

S&F in replacement of digital ammeter (0-500A), 3 phase, 96x96 mm with CT/PT complete all as specified & as directed by Engineer-in-charge.

S&F in replacement of push button, ON/OFF, Ref/Green complete all as specified & as directed by Engineer-in-charge.

S&F in replacement of LED indication lamp Red/Blue/Green with holder complete all as specified & as directed by Engineer-in-charge.

S&F in replacement of MCB 32 Amps, Triple Pole & Neutral 415 Volts, 10 KA, ‘C’ Curve complete all as specified & as directed by Engineer-in-charge. Make :- Legrand Cat Part No 408680 or equivalent in L&T / Schneider / ABB

S&F in replacement of MCB 6 Amps, Single Pole 240 Volts, 10 KA, ‘C’ Curve, complete all as specified and directed by Engineer-in-charge. Make :- Legrand Cat Part No 408587 or equivalent in L & T / Havells / Schneider

S&F in replacement of submersible pump controller fully star delta starter, in sheet-steel enclosure AC3 duty, 415 volts, 50 Hz, 3 Phase for 20 HP pump and relay 13-21 Amps, voltage single phasing, under voltage fault, over voltage fault complete all as specified & as directed by Engineer-in-charge. Make: L&T cat ref. No SS95984DOAO (MUG20 FASD) / Schneider / Siemens

S&F in replacement of door hinges for single/double door CRCA sheet electrical panel by welding or nut /bolts as per esixting type complete all as specified & as directed by Engineer-in-charge.

Disconnecting of gear box of Make : Elecon, Type : NU, size 3 inch, Ratio 70:1, by strip opening and greasing, oiling, lathe work, grinding finishing work on shaft including replacement of shaft key, bush/bearing, oil seal, packing, drain plug etc and painting with one coat of synthetic enamel weather proof paint as per existing colour code complete all as specified and directed by Engineer-in-charge. Note :(i) Items like gear grease, Wedge pully with key and belt etc required to replace shall be measured and paid for separately under respective items of BOQ as “Supply only”

Supply and filling gear grease Castrol EPL2 / Indian Oil Servogem EP2 complete all as specified & as directed by Engineer-in-charge.

Supply only in replacement wedge pully with key for gear box complete all as specified & as directed by Engineer-in-charge.

Supply only in replacement belt B38/B46 for gear box complete all as specified & as directed by Engineer-in-charge. Make : - Fenner, Dunlop

S&F in replacement of suction air filter for air blower complete all as specified & as directed by Engineer-in-charge. Make : Everest LB17, 50HP

S&F in replacement Vee belt suitable for air blower complete all as specified & as directed by Engineer-in-charge. Make : Everest LB17

Supply only of gear oil for air blower (Castrol Hypoy 90EP, HP EP90)

S&F in replacement Vee belt suitable for air blower 20 HP

Supply only of nylon gland packing for pump of size 10/12 sqmm

M&L for repair of gas chlorinator, semi automatic vaccum type chlorine dosing capacity upto 2.5 kg/hr by disconnecting from the chlorination system / cylinder and strip opening and replacement of unserviceable parts i.e. flow regulator with glass tube 'O' rings, filters, gaskets, main diaphram, disc diaphram, ring diaphram, nozzle, adeptor socket with washer for PVC flexible pipe etc or any other part required to make the device functional and refixing of the same and testing complete all as specified and directed by Engineer-in-charge.

M&L for repair of gas injector of chlorine dosing system capacity upto 2.5 kg/hr by disconnecting from the chlorination system and strip opening and replacement of unserviceable parts i.e. O rings, filters, gaskets, spring sport, nozzle, adeptor socket with washer for PVC flexible pipe etc or any other part required to make the device functional and refixing of the same and testing complete all as specified and directed by Engineer-in-charge.

S&F in replacement of heavy duty control valve (IS:3224) suitbale for chlorine gas cylinder (100 Kg) for connection with chorinator complete all as specified and directed by Engineer-in-charge.

S&F in replacement of yoke clamp assembly for chlorinator mounting on cylinder complete all as specified and directed by Engineer-in-charge.

S&F in repair ejector suitable for chlorine dosing capacity upto 2.5Kg/Hour as per existing model and type complete all as specified and directed by Engineer-in-charge.

S&F in repair gas chlorinator direct cylinder mounted suitable for chlorine dosing capacity upto 2 Kg per hour as per existing model and type complete with necessary fitting and testing complete all as specified and directed by Engineer-in-charge.

S&F in repair 25mm bore UPVC pipes of approved make or equivalent including fittings such as socket, bend, union & tee conrforming to IS 13592-1992 complete all as specified & directed by Engineer-in-charge.

S&F in repair 32mm bore UPVC pipes of approved make or equivalent including fittings such as socket, bend, union & tee conrforming to IS 13592-1992 complete all as specified & directed by Engineer-in-charge.

S&F in repair 25mm bore PVC ball valve, heavy duty complete all as specified & directed by Engineer-in-charge.

S&F in repair 32mm bore PVC ball valve, heavy duty complete all as specified & directed by Engineer-in-charge.

S&F in repair 9mm bore PVC flexible water pipe, heavy duty complete all as specified & directed by Engineer-in-charge.

S&F in replacement PVC foot valve for 25 mm bore pipe, ISI marked complete all as specified and directed by Engrineer-in-Charge.

S&F in replacement PVC foot valve for 32 mm bore pipe, ISI marked complete all as specified and directed by Engrineer-in-Charge.

S&F in repair to On-load change over switch I-O-II, open execution, 4 pole confirming to IS: 13947, 160Amps with handle fixed in existing electrical panel and all electrical connection complete all as specified and directed by Engrineer-in-Charge.

S&F in repair to On-load change over switch I-O-II, open execution, 4 pole confirming to IS: 13947, 400Amps with handle fixed in existing electrical panel and all electrical connection complete all as specified and directed by Engrineer-in-Charge.

Preparation of old painted surfaces of chlorine cylinder of capacity 100 Kg incl scrapping old paint, and applying two coats of spray paint using synthetic enamel paint over and writing with black colour paint as GE (Army) Suratgarh, Sr. No etc complete all as specified and directed by Engineer-in-charge.

Taking up or down 15mm bore galvanised steel water tubing including connections, fixed in walls, ceiling or laid under floor or laid in trenches etc complete all as specified and directed by Engineer-in-charge. Note :- Excavation and earthwork shall be measured and paid for separately under respective items of BOQ.

All as per Srl item No 171 above but 20 mm dia bore.

All as per Srl item No 171 above but 25 mm dia bore.

Fixing only 15mm bore old galvanised steel water tubing including cleaning with & including new fittings and fixed complete to walls and ceilings or laid in floors in new or old position complete all as specified and directed by Engineer-in-charge. Note :- GI tubing retrieved vide item No 171 shall be used under this item.

All as per Srl item No 174 above but 20 mm dia bore. Note :- GI tubing retrieved vide item No 172 shall be used under this item.

All as per Srl item No 174 above but 25 mm dia bore. Note :- GI tubing retrieved vide item No 173 shall be used under this item.

S&F in replacement 40mm bore galvanized steel water tubing medium grade with & including all fittings and fixed complete to walls and ceilings or laid in floors / trenches complete all as specified and directed by Engineer-in-charge.

All as per Srl item No 177 above but 50 mm dia bore.

All as per Srl item No 177 above but 80 mm dia bore.

All as per Srl item No 177 above but 100 mm dia bore.

All as per Srl item No 177 above but 150 mm dia bore.

S&F in replacement gun metal globe or gate valve 15mm bore with iron wheel head, screwed both ends for iron pipes complete all as specified and directed by Engineer-in-charge.

All as per Srl item No 182 above but 20 mm dia bore.

All as per Srl item No 182 above but 25 mm dia bore.

All as per Srl item No 182 above but 40 mm dia bore.

All as per Srl item No 182 above but 50 mm dia bore.

Supplying & fixing DI fittings confirming to IS-9523-2000 suitable for spigot & socketed pipes such as bends (any type, radius and angle), tapers any type (straight, bend, increasing, decreasing or double socket etc),tee pieces, single branch, 'Y' junction, double branch, cross collar, caps and plugs etc. suitable for spigot and socketed pipes complete all as specified and directed by Engineer-in-charge.

Supplying, fixing and testing in replacement of 80mm bore cast iron sluice valve with langed ends drilled ISI marked class PN - 1.6 conforming to IS 14846-2000 with stainless steel spindle with iron wheel, CI gate with brass nut, bolts, washers and rubber packing for connecting pieces etc complete all as specified and as directed by Engineer-in-Charge.

All as per Srl item No 188 above but sluice valve 100 mm dia bore.

All as per Srl item No 188 above but sluice valve 150 mm dia bore.

All as per Srl item No 188 above but sluice valve 200 mm dia bore.

Supplying, fixing, commisioning and testing in replacement cast iron double orifice air release valve, ISI marked, IS:14845, PN 1.6 pressure rating with stainless steel float, flanged ends with two air outlets, 80mm dia ISI marked including jointing material such as clamps, nuts, bolts, washers and rubber sheet etc complete all as specified and directed Engr-in-Charge. Note :- Excavation and earthwork shall be measured and paid for seperately under respective items of BOQ.

S&F in replacement Cast Iron foot valve for 80 mm bore pipe, lift flanged type as per IS-4038 complete all as specified and directed by Engrineer-in-Charge.

All as per Srl item No 193 above but foot valve 100 mm dia bore.

All as per Srl item No 193 above but foot valve 150 mm dia bore.

All as per Srl item No 193 above but foot valve 200 mm dia bore.

S&F in replacement of suction flexible pipe 100mm dia, PVC material for water pump with flanged end and fixing clamp complete all as specified and directed by Engrineer-in-Charge.

Welding work and any addition / alteration, cutting and jointing blank flanged to the DI / CI / GI pipe including suitable nut bolts, washer complete all as specified and directed by Engineer-in-charge. Note :- Blank flange will be measured and paid for seprately.

Supply only in replacement of 'D' Joint / mechanical joint suitable for DI / CI pipe 100/150mm dia bore including excavation work and other fittings such as nut bolts, rubber joints etc required including testing at site complete all as specified and directed by the Engineer-in-Charge.

M&L for taking out unserviceable spindle, nut with gate assembly from sluice valve of size 80 / 100 / 150/ 200mm bore and replacement of brass nut, rubber gasket, nut bolt washer etc including welding work on spindle for filling of material etc as required anf refixing in the same position, complete all as specified and directed by Engineer-in-Charge. Note :- (i) Excavation & earthwork including dewatering etc required for the job is deemed to be included in the rate quoted.

All as per Srl item No 200 above but 250 / 300 / 350 mm dia bore.

M&L for taking out 80 / 100 / 150mm bore non return valve from the water pipe line and replacement with new synthetic leather seat best quality of suitable size, nut bolts, rubber gasket, finishing work as required to make smooth funtioning and refixing in the same position, complete all as specified and directed by Engineer-in-Charge.

All as per Srl item No 202 above but 200 / 250 / 350 mm dia bore.

M&L for repair to foot valve of 80 / 100 / 150 mm size by disconnecting from pipe line and replacement of cast iron door plate assembly, hinge pin / disc guide pin, rubber door face and rubber gasket and fixing on same location and testing complete all as specified and directed by Engrineer-in-Charge.

All as per Srl item No 204 above but 200 / 250 mm dia bore.

M&L for repair to joint of spigot and socket joints, fittings joints of CI pipe line of size 80 / 100 / 150 / 200mm by making leak proof joint by caulking with caulking tool and using lead wool and spun yarn as required on site including any excavation works as required at site complete all as specified and directed by Engineer-in-Charge. Note :- Excavation & earthwork including dewatering etc required for the job is deemed to be included in the rate quoted.

All as per Srl item No 206 above but 350 / 500 mm dia bore.

Excavation in trenches, not exc 1.5 m wide and n. exc 1.5 m depth, or n exc 10 Sqm on plan and n exc 1.5 m in depth for foundations of poles, struts, stays etc. or laying underground cable and water supply / sewage pipe line etc. in soft / loose soil & getting out including taking out old brick or precast cable cover complete all as specified and directed by Engineer-in-Charge.

Returning, filling in, including spreading, leveling watering and well ramming in layers n.exc 25 cm in soft/loose soil complete all as specified and directed by Engineer-in-charge.

Removal of excavated soil/ material to a distance not exc 50 metre and depositing where directed at a level not exc 1.50 metre above the starting point complete all as specified and directed by Engineer-in-charge.

S&F in replacement outer body of pump (Make Kirloskar Model - DB 125/40, total head 60 mtr, discharge capacity 180 m3/hr and matching with existing and testing complete all as specified and directed by Engineer-in-Charge. Note :- Old unserviceable outer body shall be deposited in AGE E/M store yard by the contractor at his own arrangement. Noting extra shall be paid on this account.

S&F in replacement outer body of pump (Make Kirloskar Model - DB 125/40, total head 50 mtr, discharge capacity 180 m3/hr and matching with existing and testing complete all as specified and directed by Engineer-in-Charge. Note :- Old unserviceable outer body shall be deposited in AGE E/M store yard by the contractor at his own arrangement. Noting extra shall be paid on this account.

S&F in replacement outer body of pump (Make Kirloskar Model - DB 125/40, total head 40 mtr, discharge capacity 180 m3/hr and matching with existing and testing complete all as specified and directed by Engineer-in-Charge. Note :- Old unserviceable outer body shall be deposited in AGE E/M store yard by the contractor at his own arrangement. Noting extra shall be paid on this account.

Disconnecting electric supply of motor pump set from main panel board, suction, discharge line and keeping aside for foundation repair work and replacement nuts bolts of pump set, taking out and refixing pump set and testing after foundation repair complete all as specified and directed by the Engineer-in-Charge.

Demolition of cement concrete unreinforced of any description and in any position not otherwise specifically provided for complete all as specified and directed by Engineer-in-charge.

M & L for PCC (1:3:6) typeC-2 using 40mm graded stone aggregate as in foundation for motors & mass concrete including necessary form work and fair finishing complete all as specified and directed by Engineer-in-charge

M&L for repair fabrication of irom frame structure for supporting different pipe network and fabrication of foundation of pump set, iron jali, stair, sludge scrap trap jali, strainer etc as inlcuding welding work as required including one coat of red oxide oxide premier and two coat of synthetic enamel paint weather proof complete all as specified and directed by Engineer-in-charge.

Taking sample from water supply installation in stirlized bottle (5 Ltrs) and testing of water for bactoriological examination test, chemical examination test (i.e. pH, NTU, Total Hardness, total alkalinity, chloride, TDS, Residual Chlorine etc at PHED Distt Laboratory Ganganagar Rajasthan or other Govt recognized Lab.

Taking up or down 15mm bore PVC pipe including connections, fixed in walls, ceiling or laid under floor or laid in trenches etc complete all as specified and directed by Engineer-in-charge. Note :- Excavation and earthwork shall be measured and paid for separately under respective items of BOQ.

S&F 15mm bore galvanized steel water tubing medium grade with & including all fittings and fixed complete to walls and ceilings or laid in floors / trenches complete all as specified and directed by Engineer-in-charge.

All as per Srl item No 220 above but 20 mm dia bore.

All as per Srl item No 220 above but 25 mm dia bore. -------------------------------------------------------------------------- Note :- A sum of Rs. 263178/- will be deducted on account of credit for dismantled/ demolished / taken down material. Please refer details on Srl Page No. 32 to 34 (Schedule of Credit) of Tender documents.

J.M.D. CONSTRUCTION CO.