BALANCE WORK OF PROVN OF OTM ACCN FOR CERTAIN UNITS AT RANGAPAHAR MIL STN UNDER GE 868 EWS

Amount

NOTE:- (Applicable for all parts/items/):- The bidders/contractors are advised to read tender document, all drawings & all corrigendum/ amendments and General conditions of contracts before entry/quoting the rates.

Lumpsum price workedout by the tenderer for BUILDING & STRUCTURE WORKS as listed in Schedule ‘A’ Part-I

Lumpsum price worked out by the bidder/ tenderer for SITE CLEARANCE, SITE DEVELOPMENTS & EARTH WORKS as listed in Schedule 'A' Part-II.

Lumpsum price worked out by the bidder/ tenderer for INTERNAL WATER SUPPLY/ HOT WATER SUPPLY as listed in Schedule 'A' Part-III.

Lumpsum price worked out by the bidder/ tenderer for INTERNAL ELECTRIFICATION as listed in Schedule 'A' Part-IV.

Lumpsum price worked out by the bidder/ tenderer for ROADS/CULVERTS/ HARDSTANDING as listed in Schedule 'A' Part-V.

Lumpsum price worked out by the bidder/ tenderer for SEWAGE DISPOSAL as listed in Schedule 'A' Part-VI.

Lumpsum price worked out by the bidder/ tenderer for AREA DRAINAGE as listed in Schedule 'A' Part-VII.

Lumpsum price worked out by the bidder/ tenderer for RETAINING WALL as listed in Schedule 'A' Part-VIII.

Lumpsum price worked out by the bidder/ tenderer for EXTERNAL WATER SUPPLY as listed in Schedule 'A' Part-IX.

Lumpsum price worked out by the bidder/ tenderer for EXTERNAL ELECTRIFICATION as listed in Schedule 'A' Part-X.

Lumpsum price worked out by the bidder/ tenderer for DEMOLITION & DISMANTLING as listed in Schedule 'A' Part-XI.

Lumpsum price worked out by the bidder/ tenderer for AIR CONDITIONING/ REFRIGERATION as listed in Schedule 'A' Part-XII.

Lumpsum price worked out by the bidder/ tenderer for SECURITY FENCING / GATE as listed in Schedule 'A' Part-XIII.

Sch 'A' Sec-XIV (Miscellaneous Items) Note : This schedule is not pre-priced by MES and the pre-priced rate indicated as "Rs 0.00" under Col. 5 siginifies this fact only.

Supply and fixing ceiling fan energy saving and fancy type 1200 mm(minimum) sweep three blade, 5 star BEE rating without regulator including hanging rod and necessary connecting PVC insulated Flexible cable for connection from ceiling rose to fan and connecting complete all as specified and as directed. Make: Model- ES-50 of Havells or equivalent make as per Appendix 'B'.

Exhaust fan 300mm(min) sweep MS CRCA body and metal blades with double bearing metal protective bird guard , AC single phase, including electrical connection with twisted three core PVC insulated flexible cord of size 0.75sqmm copper conductor from celing rose complete all as specified and as directed. Make: Model- Ventil Air - DX of Havells or equivalent make as per Appendix 'B'.

Sheet metal enclosure vertical distribution board TPN 415 Volt 8 way ,double door type and provision for 4 pole MCCB as a incomer complete with 100 Amps rated vertical insulated busbar complete all as specified and as directed.

MCCB 4 pole, 100 Amps capacity, bearking capacity 16 KA with fixed thermal and fixed magnetic setting complete all as specified and as directed.

MCCB 4 pole, 63 Amps capacity, breaking capacity 16 KA with fixed thermal and fixed magnetic setting complete all as specified and as directed.

Supply and fixing voltage stabilizer for automatic operation, single phase with neutral, natural air cooled wall mounted indoor type and designed for input voltage variation between 170 volt to 250 volt with output voltage stabilized at 230 volt with accuracy of +/- 2.5% and capacity of 3 KVA complete all as specified.

Supply and fixing voltage stabilizer for automatic operation, single phase with neutral, natural air cooled wall mounted indoor type and designed for input voltage variation between 170 volt to 250 volt with output voltage stabilized at 230 volt with accuracy of +/- 2.5% and capacity of 5 KVA complete all as specified.

Supply, laying and testing of 150mm internal diameter of double wall corrugated(DWC) high density polyethylene pipes (HDPE) and stiffness classes-8 (SN-8) with ISI marked(with CML no) with and including all fitting & jointing material for sewage line and laid in trenches as specified in IS-16098-2013 part-2 complete all as specified and as directed. Make :- Rex Polyextrusion Pvt Ltd/Jain Irriogation Systems Ltd/ Alom Poly Extrusions Limited Note:- Bedding of pipe shall not be provided in normal condition and CONSTRUCTION METHODS shall be strictly compiled as per clause no A-4 of ANNEX 'A' of IS 16098 part-II .

Supply, installation, testing & commissioning of Automatic washing machine of minimum capacity 30 kg per charge made out stainless steel inner basket and outer drum with steam heated, front loading, auto timed, auto stop, auto reverse, auto temperature control, auto drain, auto water level with control-panel including suitable capacity of motor complete all as specified and as directed. Make:-BTC / FABCARE/ Superfab Machinery

Supply and fixing voltage stabilizer for automatic operation, single phase with neutral, natural air cooled indoor type and designed for input voltage variation between 170 volt to 250 volt with output voltage stabilized at 230 volt with accuracy of +/- 2.5% and capacity of 0.5 KVA complete all as specified and as directed.

Supply and fixing voltage stabilizer for automatic operation, single phase with neutral, natural air cooled indoor type and designed for input voltage variation between 170 volt to 250 volt with output voltage stabilized at 230 volt with accuracy of +/- 2.5% and capacity of 1 KVA complete all as specified and as directed.

Supply, installation, testing and commissioning refrigerator electric driven single phase capacity 210 litres(± 2%) frost free, single door, BEE five star rated and complete all as specified.

Supply, installation, testing & commissioning Pre-filter of single candle with enclosure for filtering impurities upto 5 micron complete all as specified and directed. Make : Aquaguard/Kemflo

Supply, laying and jointing of ductile iron pipes with spigot and socket ends suitable for push on rubber joint centrifugally cast, class (K-7) , inner side cement lining and outer side black bitumen coating and any length, laid in trenches of 150mm bore pipe and including push on rubber (EPDM) ring with ISI marked complete all as specified complete.

Supply, laying & fixing of ductile Iron pipe fittings sutable for flange,spigot & socket pipe complete all as specified and directed.

Supply & fixing of transparent street light junction box of size 200 mm x 160 mmx98 mm made of high quality polycarbonate I IP-65 (Dust and power jet Proof according to IEC 60529) , shock proof, rust free, corrosion free acid and chemical resistant, fire retardant having high impact (IK 08) totally insulated (Class II ) made of halogen and silica free recyclable material, UV resistant having high grade gasket made of polyurethane with copper bus bar 25 x 5 mm -04 strip, one no MCB DP 6 Amps with locking arrangement and 2 Nos M40 size cable gland and one M32 size gland suitable up to, 50Sqmm cable etc complete all as specified and directed Make: HENSEL Cat No KF 9255or equivalent model of BCH/LEGRAND

Material and labour for pre - cast RCC post HT cable route indicator made up of RCC (1:2:4) of overall size 100 x 100 x 1200 mm (H) and 200x200mm bottom with 4 nos 8 mm dia TMT bar on vertical and 8 mm TMT stirrups at 150c/c incl binding wire and embossing "MES HT/LT CABLE" on all four sides and fixed at cable trench during returning filling of soil keeping 500mm above ground complete all as specified and as directed.

Supply, installation, testing and commissioning of factory made powder coated (CPRI approved) outdoor type, dust & vermin proof feeder pillar box made out of 3.15mm CRCA steel sheet of suitable size and angle iron 40 mm x 40mm x 6 mm , powder coated over one coat of red oxide primer suitably grouted in PCC-M10 using 20 mm graded stone aggregate including bus bar, internal wiring with PVC insulated single core cables of copper conductor of suitable size duly numbered with tags for the circuits with hinged double door shutters (front & rear), cubical type locking arrangement and slanted roof. The size of panel boards shall be suitable for housing the accessories given here under and also suitable for operation on AC 415 Volt, 3 phase, 50 Hz supply system. The panel board shall comprise of following items & all specified in SSR Part-I clause no 19.21 and all as shown on drawing . (A) INCOMING:- (i) MCCB 160 amps, 4 pole, breaking capacity 25 KA suitable for operation of 415 volts AC 50 HZ - 01 No, (ii) 4 strip aluminum coated copper bus bar of rating 1.5 times current carrying capacity of incoming switch gear or not less than 200 Amp whichever higher (B) OUTGOING (i) MCCB 40 A, 3 Pole, 415 Volts, 16 KA - 02 No (ii) MCCB 25A, 3 Pole, 415 Volts, 16 KA - 02 No(iii)MCCB 16A, 3 Pole, 415 Volts, 16 KA - 02 No (iv) MCB 6-32A, 2 Pole, 240 Volts, 10KA - 02 No (v) space for one MCCB

Supply, installation, testing and commissioning of factory made powder coated (CPRI approved) outdoor type, dust & vermin proof feeder pillar box made out of 3.15mm CRCA steel sheet of suitable size and angle iron 40 mm x 40mm x 6 mm , powder coated over one coat of red oxide primer suitably grouted in PCC-M10 using 20 mm graded stone aggregate including bus bar, internal wiring with PVC insulated single core cables of copper conductor of suitable size duly numbered with tags for the circuits with hinged double door shutters (front & rear), cubical type locking arrangement and slanted roof. The size of panel boards shall be suitable for housing the accessories given here under and also suitable for operation on AC 415 Volt, 3 phase, 50 Hz supply system. The panel board shall comprise of following items & all specified in SSR Part-I clause no 19.21 and all as shown on drawing . (A) INCOMING:- (i) MCCB 160 amps, 4 pole, breaking capacity 36 KA suitable for operation of 415 volts AC 50 HZ - 01 No, (ii) 4 strip aluminum coated copper bus bar of rating 1.5 times current carrying capacity of incoming switch gear or not less than 200 Amp whichever higher (B) OUTGOING (i) MCCB 100 A, 3 Pole, 415 Volts, 16 KA - 01 No (ii) MCCB 63A, 3 Pole, 415 Volts, 16 KA - 01 No (iii) MCCB 25A, 3 Pole, 415 Volts, 16 KA - 01 No (iii) Blank (iii) space for one MCCB

Supply, installation, testing and commissioning of factory made powder coated (CPRI approved) outdoor type, dust & vermin proof feeder pillar box made out of 3.15mm CRCA steel sheet of suitable size and angle iron 40 mm x 40mm x 6 mm , powder coated over one coat of red oxide primer suitably grouted in PCC-M10 using 20 mm graded stone aggregate including bus bar, internal wiring with PVC insulated single core cables of copper conductor of suitable size duly numbered with tags for the circuits with hinged double door shutters (front & rear), cubical type locking arrangement and slanted roof. The size of panel boards shall be suitable for housing the accessories given here under and also suitable for operation on AC 415 Volt, 3 phase, 50 Hz supply system. The panel board shall comprise of following items & all specified in SSR Part-I clause no 19.21 and all as shown on drawing . (A) INCOMING:- (i) MCCB 63 amps, 4 pole, breaking capacity 16 KA suitable for operation of 415 volts AC 50 HZ - 01 No, (ii) 4 strip aluminum coated copper bus bar of rating 1.5 times current carrying capacity of incoming switch gear or not less than 200 Amp whichever higher (B) OUTGOING (i) MCCB 40 A, 3 Pole, 415 Volts, 16 KA - 01 No (ii) MCCB 25 A, 3 Pole, 415 Volts, 16 KA - 02 No (iii) MCCB 16 A, 3 Pole, 415 Volts, 16 KA - 01 No (iv) MCB 6-32A, 2 Pole, 240 Volts, 10KA - 01 No (v) space for one MCCB

Supply, installation, testing and commissioning of factory made powder coated (CPRI approved) outdoor type, dust & vermin proof feeder pillar box made out of 3.15mm CRCA steel sheet of suitable size and angle iron 40 mm x 40mm x 6 mm , powder coated over one coat of red oxide primer suitably grouted in PCC-M10 using 20 mm graded stone aggregate including bus bar, internal wiring with PVC insulated single core cables of copper conductor of suitable size duly numbered with tags for the circuits with hinged double door shutters (front & rear), cubical type locking arrangement and slanted roof. The size of panel boards shall be suitable for housing the accessories given here under and also suitable for operation on AC 415 Volt, 3 phase, 50 Hz supply system. The panel board shall comprise of following items & all specified in SSR Part-I clause no 19.21 and all as shown on drawing . (A) INCOMING:- (i) MCCB 63 amps, 4 pole, breaking capacity 16 KA suitable for operation of 415 volts AC 50 HZ - 01 No, (ii) 4 strip aluminum coated copper bus bar of rating 1.5 times current carrying capacity of incoming switch gear or not less than 100 Amp whichever higher (B) OUTGOING (i) MCCB 32 A, 3 Pole, 415 Volts, 16 KA - 01 No (ii) MCCB 25 A, 3 Pole, 415 Volts, 16 KA - 02 No (iii) MCCB 16 A, 3 Pole, 415 Volts, 16 KA - 01 No (iv) MCB 6-32A, 2 Pole, 240 Volts, 10KA - 01 No (v) space for one MCCB

Supply, installation, testing and commissioning split type air conditioner electrical driven with cordless remote control unit, single phase of capacity 1 TR, minimum 5 star rated with all insulated PVC tube, 3core PVC wire suitable size complete all as specified.

Supply, install , testing and commissioning of LED Solar Street Light, 20 Watt stand alone system including following accessories:- (a) White Light Emitting Diode (W-LED) Luminaire 20 W with consisting alumimium housing of heat dissipation IP65 protection with new age high lumen LEDs for high efficiency light sources, optical engineering for uniform light distribution. (b) Solar Panel 100 WP polycrystalline silicon solar cells panel. (c) Low maintenance lead acid Battery 12V DC, 100 AH, tubular construction with low discharge rate mounted on weather-proof Galvanised battery box. (d) Rigid and corrosion free galvanised pole 88.9 mm OD in lower portion & 76.1 mm OD in upper portion of pole with 6.0 mtr long (5m above ground level). (e) Control electronics consist of microprocessor based charge controller, and LED driver to maximises the performance of panel & battery, Dusk to down automatic switch on/off of street light, over charge protection of battery, deep discharge protection of battery. (f) 2 mm thick MS battery box with locking arrangement . (g) Interconnecting cables/ wires & including all other standard accessories as per manufacturing instruction complete. (h) autonomy 3 days (assuming 12 hours of usage per day) (i) The street lighting system (including the battery) shall be warranted for a period of five years from the date of completion of works. Note : Necessary excavation & earth work, PCC work for foundation & coping will be measured & paid separately. Make: PHILIPS, Model No. BRP 020 or equivalent model of BAJAJ/TATA BP Solar.

Supply , Fixing & testing of LED street light fitting of 60 Watt with LED lamp’s & driver and made of pressure die-cast aluminum housing, IP 65/IP 66 road way luminaries with UV stabilized polycarbonate cover or toughen glass cover & high power LED’s as light source with LED fitting system lumen not less than 95% Lumen per watt and electronic driver with efficiency > 85% with inbuilt protection against lightning, over voltage, short circuit and surge/spike protection upto 5 KV ensuring longer life (THD <10%, PF shall be > 0.95, colour temperature 5700±300 K), Life expectancy of LED's minimum 50,000 burning hrs, warranty of complete luminaries fitting shall not less than three years. The fitting shall be tested LM 79 & 80 and test certificate shall be submitted from original manufacture. The light fitting shall be fixed on pole with and including 32 mm dia( or higher size as per manufacturers recommendation) light grade GI pipe (bend to shape or as per manufacturers recommendation ) bracket 1.5 mtr long complete with MS flat iron clamp (clamps shall be 40 x 5 mm MS flat) nuts, bolts & washers including painting the clamps with two coat of aluminium paint over a coat of red oxide primer including connection with two core 2.50 sqmm flexible copper conductor to control street light from junction box to street light fitting complete all as specified and directed.

Supply , Fixing & testing of LED street light fitting ( Building Security light) of 30Watt with LED lamp’s & driver and made of pressure die-cast aluminum housing, IP 65/IP 66 road way luminaries with UV stabilized polycarbonate cover or toughen glass cover & high power LED’s as light source with LED fitting system lumen not less than 95% Lumen per watt and electronic driver with efficiency > 85% with inbuilt protection against lightning, over voltage, short circuit and surge/spike protection upto 5 KV ensuring longer life (THD <10%, PF shall be > 0.95, colour temperature 5700±300 K), Life expectancy of LED's minimum 50,000 burning hrs, warranty of complete luminaries fitting shall not less than three years. The fitting shall be tested LM 79 & 80 and test certificate shall be submitted from original manufacture. The light fitting shall be fixed on pole with and including 25 mm dia( or higher size as per manufacturers recommendation) light grade GI pipe (bend to shape or as per manufacturers recommendation ) bracket 1.5 mtr long complete with MS flat iron clamp (clamps shall be 40 x 5 mm MS flat) nuts, bolts & washers including painting the clamps with two coat of aluminium paint over a coat of red oxide primer including connection with two core 2.50 sqmm flexible copper conductor to control street light from ceiling rose to street light fitting complete all as specified and directed.

Supply & fixing of LED flood light fitting 100 Watt(minimum) with LED lamp, di- cast aluminium housing with heat resistant clear glass cover, suitable type gasket & high power LED’s as light source with LED fitting system lumen not less than 95% Lumen per watt and electronic driver( >80% efficiency level & THD< 10%) , power factor shall be >0.95, ( >80% efficiency level & THD< 10%) , power factor shall be >0.95 complete and including all other standard accessories as per manufacture instructions ,internally pre-wired including connecting up 3 core 1 sqmm copper conductor flexible wire/cable complete all as specified. MAKE : Model no BARFEG 100W LED of Bajaj or equivalent model of make as mention Appendix "B"

LED surface mounted light fitting 36 Watt with LED Lamp , drive and made of epoxy powder coated extruded CARC sheet housing & high power LED’s as light source with LED fitting system lumen not less than 95% Lumen per watt and electronic driver( >80% efficiency level & THD< 10%) , power factor shall be >0.95, ( >80% efficiency level & THD< 10%) , power factor shall be >0.95 complete and including all other standard accessories as per manufacture instructions ,internally pre-wired including connecting up 3 core 1 sq. mm copper conductor flexible wire/cable complete all as specified. Make : Model No BZSSQL 36WWH of BAJAJ or equivalent model of make list as given in Appdix "B"

LED surface mounted light fitting 18Watt with LED Lamp , drive and made of epoxy powder coated extruded CARC sheet housing & high power LED’s as light source with LED fitting system lumen not less than 95% Lumen per watt and electronic driver( >80% efficiency level & THD< 10%) , power factor shall be >0.95, ( >80% efficiency level & THD< 10%) , power factor shall be >0.95 complete and including all other standard accessories as per manufacture instructions ,internally pre-wired including connecting up 3 core 1 sqmm copper conductor flexible wire/cable complete all as specified. Make : Model No BZSSQL18 W WH of BAJAJ or equivalent model of make list as given in Appdix "B"

LED ballard light fitting 9 Watt, made of die cast aluminum wing shaped powder coated housing with UV stabilized opal acrylic cover including & high power LED’s as light source with LED fitting system lumen not less than 95% Lumen per watt and electronic driver( >80% efficiency level & THD< 10%) , power factor shall be >0.95, with opal acrylic and IP65 protection and fixed on PCC/birck pillar with MS nut& bolt and including connecting up with suitable size of copper conductor cable from junction box complete all as specified and directed . Make : Model No- BGBOM 650 9W LED Bajaj or equivalent model of make list as given in Appdix "B".

LED surface/ceiling mounting(suspended from ceiling) box type light fitting 20Watt with LED Lamp , drive and made of epoxy powder coated extruded aluminium channel housing with high quality polycarbonate opal diffuser cover & high power LED’s as light source with LED fitting system lumen not less than 95% Lumen per watt and electronic driver( >80% efficiency level & THD< 10%) , power factor shall be >0.95, ( >80% efficiency level & THD< 10%) , power factor shall be >0.95 complete and including all other standard accessories as per manufacture instructions ,internally pre-wired including connecting up 3 core 1 sqmm copper conductor flexible wire/cable complete all as specified. Make : Model No for Batten BLRB DB 118 & LED tube BLRB 21W CWC of BAJAJ or Model No for BattenLL 13 PRO LED & LED tube SSK T5 22W of SYSKA LED equivalent model of make list as given in Appdix "B".

LED surface/ceiling mounting(suspended from ceiling) box type light fitting 40Watt with LED Lamp , drive and made of epoxy powder coated extruded aluminium channel housing with high quality polycarbonate opal diffuser cover including & high power LED’s as light source with LED fitting system lumen not less than 95% Lumen per watt and electronic driver( >80% efficiency level & THD< 10%) , power factor shall be >0.95, ( >80% efficiency level & THD< 10%) , power factor shall be >0.95 complete and including all other standard accessories as per manufacture instructions ,internally pre-wired including connecting up 3 core 1 sqmm copper conductor flexible wire/cable complete all as specified. Make : Model No BLTRU 40W NW VIVA of BAJAJ or equivalent model of make list as given in Appdix "B".

Supply & fixing of LED flood light fitting 60 Watt(minimum) with LED lamp, di- cast aluminium housing with heat resistant clear glass cover, suitable type gasket & high power LED’s as light source with LED fitting system lumen not less than 95% Lumen per watt and electronic driver( >80% efficiency level & THD< 10%) , power factor shall be >0.95, ( >80% efficiency level & THD< 10%) , power factor shall be >0.95 complete and including all other standard accessories as per manufacture instructions ,internally pre-wired including connecting up 3 core 1 sqmm copper conductor flexible wire/cable complete all as specified. MAKE : Model no BJFL 60W LED of Bajaj or equivalent model of make as mention Appendix "B"

Supply & fixing of LED wall mounting light fitting9 Watt(minimum) with LED lamp ,& high power LED’s as light source with LED fitting system lumen not less than 95% Lumen per watt and electronic driver( >80% efficiency level & THD< 10%) , power factor shall be >0.95 including di- cast aluminium housing with heat resistant clear glass cover, suitable type gasket and IP 65 portion including all other standard accessories as per manufacture complete all as specified and directed . MAKE : Model noLW 01 101XX60XX Wipro or equivalent model of make as mention Appendix "B"

Lamp holder, PVC/Polycarbonate type with black plate suitable for batten fittings and including 1x 5 watt LED lamp.

Supply & fixing of LED wall mounting light fitting10 Watt(minimum) with LED lamp , & high power LED’s as light source with LED fitting system lumen not less than 95% Lumen per watt and electronic driver( >80% efficiency level & THD< 10%) , power factor shall be >0.95 including di- cast aluminium housing with heat resistant clear glass cover, suitable type gasket and IP 65 portion including all other standard accessories as per manufacture complete all as specified and directed . Make :- Havells, Type: ENDURAL LINEAR NEO 10W or equivalent model of make list as given in Appdix "B".. Note for items no 13.22 to 13.34 : Warranty of complete LED luminaries fitting shall not less than three years and Life expectancy of LED's minimum 50,000 burning hrs,

Lumpsum price worked out by the tenderer for Provisional sum of Rs. 1201300.00 for following items including of earth work, concrete work, steel section etc. complete all as directed. (i) Mulipurpose Ground : 01 No (ii) Volley ball court : 01 No (iii) Basket Ball Court : 02 Nos (iv) Steel gate : 06 Nos Note:- Contactor shall quote, contractors percentage (amount) plus/minus pre-prices amount.

Golden Traders